Commit Graph

59 Commits

Author SHA1 Message Date
Andy Shevchenko dc33d13c5e gpio: mpc8xxx: Remove unused of_gpio.h inclusion
of_gpio.h shouldn't be used in GPIO drivers. Remove it.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-06-19 14:45:15 +02:00
Michal Smulski 19b60f8410 gpio: mpc8xxx: latch GPIOs state on module load when configured as output
Qoriq and related devices allow reading out state of GPIO set as output.
However, currently on driver's init, all outputs are configured as driven
low. So, any changes to GPIO confiuration will drive all pins (configured
as output) as output-low.
This patch latches state of output GPIOs before any GPIO configuration
takes place. This preserves any output settings done prior to loading
the driver (for example, by u-boot).

Signed-off-by: Michal Smulski <michal.smulski@ooma.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2023-06-16 11:11:27 +02:00
Pali Rohár 279c12df8d gpio: mpc8xxx: Fix support for IRQ_TYPE_LEVEL_LOW flow_type in mpc85xx
Commit e39d5ef678 ("powerpc/5xxx: extend mpc8xxx_gpio driver to support
mpc512x gpios") implemented support for IRQ_TYPE_LEVEL_LOW flow type in
mpc512x via falling edge type. Do same for mpc85xx which support was added
in commit 345e5c8a1c ("powerpc: Add interrupt support to mpc8xxx_gpio").

Fixes probing of lm90 hwmon driver on mpc85xx based board which use level
interrupt. Without it kernel prints error and refuse lm90 to work:

    [   15.258370] genirq: Setting trigger mode 8 for irq 49 failed (mpc8xxx_irq_set_type+0x0/0xf8)
    [   15.267168] lm90 0-004c: cannot request IRQ 49
    [   15.272708] lm90: probe of 0-004c failed with error -22

Fixes: 345e5c8a1c ("powerpc: Add interrupt support to mpc8xxx_gpio")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
2022-09-07 13:17:23 +02:00
Thomas Gleixner 3bb165608e treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_56.RULE (part 2)
Based on the normalized pattern:

    this file is licensed under the terms of the gnu general public
    license version 2 this program is licensed as is without any warranty
    of any kind whether express or implied

extracted by the scancode license scanner the SPDX license identifier

    GPL-2.0-only

has been chosen to replace the boilerplate/reference.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-06-10 14:51:35 +02:00
Yang Li 9f51ce0b9e gpio: mpc8xxx: Fix an ignored error return from platform_get_irq()
The return from the call to platform_get_irq() is int, it can be
a negative error code, however this is being assigned to an unsigned
int variable 'irqn', so making 'irqn' an int.

Eliminate the following coccicheck warning:
./drivers/gpio/gpio-mpc8xxx.c:391:5-21: WARNING: Unsigned expression
compared with zero: mpc8xxx_gc -> irqn < 0

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: 0b39536cc6 ("gpio: mpc8xxx: Fix IRQ check in mpc8xxx_probe")
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
2022-01-20 09:05:57 +01:00
Miaoqian Lin 0b39536cc6 gpio: mpc8xxx: Fix IRQ check in mpc8xxx_probe
platform_get_irq() returns negative error number instead 0 on failure.
And the doc of platform_get_irq() provides a usage example:

    int irq = platform_get_irq(pdev, 0);
    if (irq < 0)
        return irq;

Fix the check of return value to catch errors correctly.

Fixes: 76c47d1449 ("gpio: mpc8xxx: Add ACPI support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
2022-01-17 14:17:42 +01:00
Linus Torvalds 5e6a5845dd gpio updates for v5.15
- new driver: gpio-virtio allowing a guest VM running linux to access
   GPIO lines provided by the host
 - split the GPIO driver out of the rockchip pin control driver
 - add support for a new model to gpio-aspeed-sgpio, refactor the driver
   and use generic device property interfaces, improve property sanitization
 - add ACPI support to gpio-tegra186
 - improve the code setting the line names to support multiple GPIO banks
   per device
 - constify a bunch of OF functions in the core GPIO code and make the
   declaration for one of the core OF functions we use consistent within its
   header
 - use software nodes in intel_quark_i2c_gpio
 - add support for the gpio-line-names property in gpio-mt7621
 - use the standard GPIO function for setting the GPIO names in gpio-brcmstb
 - fix a bunch of leaks and other bugs in gpio-mpc8xxx
 - use generic pm callbacks in gpio-ml-ioh
 - improve resource management and PM handling in gpio-mlxbf2
 - modernize and improve the gpio-dwapb driver
 - coding style improvements in gpio-rcar
 - documentation fixes and improvements
 - update the MAINTAINERS entry for gpio-zynq
 - minor tweaks in several drivers
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEEFp3rbAvDxGAT0sefEacuoBRx13IFAmE3ItgACgkQEacuoBRx
 13LKqA//Q2E9QYJx0lLO0C15JKzJjqYGyVqSm73Huo8pKWRSKr9YuB4/tBPKz5Ya
 pg/h7wbsk+mtQ0pqot/SEGVLo1rK6ZcPiCDkYkuaVsY9pS0zX7A/Sb2N7xKML+Nj
 wTFuhSZH2byxH6QgUrX3RLMagW4p/owlDvFjZ6Z6Vh8Ulsnb0pdL3nYg5L017GMT
 A1ySzbP79NK3LfOLTqdqgALv4EF2x+paolyEpI/Jv0naBYkIP4AcbOBQEVMpoCY/
 XEcIdPvqMyPm4PdYSy3iCqtkf7jclDbV030SHlir2bKHjI79l8ARy0Tu6hvISRSG
 8XMwt6ke40GYnPkESZTkWlqeVHYzli84FxYXYLnqFa/21c4qswHk/aZZq5h83fn8
 7aonkEQQuHfQM00MvLu0mhtKXYdLbqv7jjd0CYChwxQSpu0iu7IQSWW8c2YmGvvt
 vqfM8TdKyGNPAmSl2/enPKOr+LugG4rcgMehU9/p6QvHbB6y2SxC1MykldPOdC6d
 53PeDeNP6XOp2s10zVPWh6P0rbrMaEtv/GZ143kUw9bhb1g3woX5SaS7W76cOXhE
 kty6g1e8xNaKDZbJ++UAh7G9IGQdtz0xRCXDUHFUc89uCThc9RcHowNPtzMMnmgM
 ucWJ81XnGDSDyzzG/f7uhcOtszWYCOtFmteooaMGB36/pH2CG9Y=
 =y/RY
 -----END PGP SIGNATURE-----

Merge tag 'gpio-updates-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux

Pull gpio updates from Bartosz Golaszewski:
 "We mostly have various improvements and refactoring all over the place
  but also some interesting new features - like the virtio GPIO driver
  that allows guest VMs to use host's GPIOs. We also have a new/old GPIO
  driver for rockchip - this one has been split out of the pinctrl
  driver.

  Summary:

   - new driver: gpio-virtio allowing a guest VM running linux to access
     GPIO lines provided by the host

   - split the GPIO driver out of the rockchip pin control driver

   - add support for a new model to gpio-aspeed-sgpio, refactor the
     driver and use generic device property interfaces, improve property
     sanitization

   - add ACPI support to gpio-tegra186

   - improve the code setting the line names to support multiple GPIO
     banks per device

   - constify a bunch of OF functions in the core GPIO code and make the
     declaration for one of the core OF functions we use consistent
     within its header

   - use software nodes in intel_quark_i2c_gpio

   - add support for the gpio-line-names property in gpio-mt7621

   - use the standard GPIO function for setting the GPIO names in
     gpio-brcmstb

   - fix a bunch of leaks and other bugs in gpio-mpc8xxx

   - use generic pm callbacks in gpio-ml-ioh

   - improve resource management and PM handling in gpio-mlxbf2

   - modernize and improve the gpio-dwapb driver

   - coding style improvements in gpio-rcar

   - documentation fixes and improvements

   - update the MAINTAINERS entry for gpio-zynq

   - minor tweaks in several drivers"

* tag 'gpio-updates-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (35 commits)
  gpio: mpc8xxx: Use 'devm_gpiochip_add_data()' to simplify the code and avoid a leak
  gpio: mpc8xxx: Fix a potential double iounmap call in 'mpc8xxx_probe()'
  gpio: mpc8xxx: Fix a resources leak in the error handling path of 'mpc8xxx_probe()'
  gpio: viperboard: remove platform_set_drvdata() call in probe
  gpio: virtio: Add missing mailings lists in MAINTAINERS entry
  gpio: virtio: Fix sparse warnings
  gpio: remove the obsolete MX35 3DS BOARD MC9S08DZ60 GPIO functions
  gpio: max730x: Use the right include
  gpio: Add virtio-gpio driver
  gpio: mlxbf2: Use DEFINE_RES_MEM_NAMED() helper macro
  gpio: mlxbf2: Use devm_platform_ioremap_resource()
  gpio: mlxbf2: Drop wrong use of ACPI_PTR()
  gpio: mlxbf2: Convert to device PM ops
  gpio: dwapb: Get rid of legacy platform data
  mfd: intel_quark_i2c_gpio: Convert GPIO to use software nodes
  gpio: dwapb: Read GPIO base from gpio-base property
  gpio: dwapb: Unify ACPI enumeration checks in get_irq() and configure_irqs()
  gpiolib: Deduplicate forward declaration in the consumer.h header
  MAINTAINERS: update gpio-zynq.yaml reference
  gpio: tegra186: Add ACPI support
  ...
2021-09-07 12:27:27 -07:00
Christophe JAILLET 889a1b3f35 gpio: mpc8xxx: Use 'devm_gpiochip_add_data()' to simplify the code and avoid a leak
If an error occurs after a 'gpiochip_add_data()' call it must be undone by
a corresponding 'gpiochip_remove()' as already done in the remove function.

To simplify the code a fix a leak in the error handling path of the probe,
use the managed version instead (i.e. 'devm_gpiochip_add_data()')

Fixes: 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2021-08-31 12:10:24 +02:00
Christophe JAILLET 7d6588931c gpio: mpc8xxx: Fix a potential double iounmap call in 'mpc8xxx_probe()'
Commit 76c47d1449 ("gpio: mpc8xxx: Add ACPI support") has switched to a
managed version when dealing with 'mpc8xxx_gc->regs'. So the corresponding
'iounmap()' call in the error handling path and in the remove should be
removed to avoid a double unmap.

This also allows some simplification in the probe. All the error handling
paths related to managed resources can be direct returns and a NULL check
in what remains in the error handling path can be removed.

Fixes: 76c47d1449 ("gpio: mpc8xxx: Add ACPI support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2021-08-31 12:10:12 +02:00
Christophe JAILLET 555bda42b0 gpio: mpc8xxx: Fix a resources leak in the error handling path of 'mpc8xxx_probe()'
Commit 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
has introduced a new 'goto err;' at the very end of the function, but has
not updated the error handling path accordingly.

Add the now missing 'irq_domain_remove()' call which balances a previous
'irq_domain_create_linear() call.

Fixes: 698b8eeaed ("gpio/mpc8xxx: change irq handler from chained to normal")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2021-08-31 12:09:53 +02:00
Thomas Gleixner 47fb0cfdb7 irqchip updates for Linux 5.15
API updates:
 
 - Treewide conversion to generic_handle_domain_irq() for anything
   that looks like a chained interrupt controller
 
 - Update the irqdomain documentation
 
 - Use of bitmap_zalloc() throughout the tree
 
 New functionalities:
 
 - Support for GICv3 EPPI partitions
 
 Fixes:
 
 - Qualcomm PDC hierarchy fixes
 
 - Yet another priority decoding fix for the GICv3 pseudo-NMIs
 
 - Fix the apple-aic driver irq_eoi() callback to always unmask
   the interrupt
 
 - Properly handle edge interrupts on loongson-pch-pic
 
 - Let the mtk-sysirq driver advertise IRQCHIP_SKIP_SET_WAKE
 -----BEGIN PGP SIGNATURE-----
 
 iQJDBAABCgAtFiEEn9UcU+C1Yxj9lZw9I9DQutE9ekMFAmEqIhgPHG1hekBrZXJu
 ZWwub3JnAAoJECPQ0LrRPXpDjPkP/Rtp6WNZ1QUfJWmHovnh/Wc6ob1DXcBwi9nX
 hy4miIJ1SWuez9G49RlQAiXZoB28B6KKCKKmouiqu7ke7WUhifS0K1ej188wjxRX
 dqRG+m9yBAqKSr0lyWLB5VVCc8XBz4oZTc28n585gHiXfAPv7u0EzW+zNrnloLU5
 NrAj6ppGFUzVT0VxRqcurbymE6OwRWjc3D+z/PhtHZ4SFOhft95CXgsdvMklqyLj
 wwiuZ0Dhj5EruSP/Z7DzbbXnMNmte3HC2/cUNPYkho4/rk+2gVnYv5kVdfPHKQCY
 Wjti/kvuPC3hdTvdw8g7VQfP63R3clZhcQ8s+myoeX5LWzyAHpoxAtdsbX7oVsgs
 aKyrFhddEFVuiFizYyweS89pL0kCkTob8/zlGeuhRiVRTZ3+kG7Zf2UTTnN1ZdLw
 2lMolghiGk4LYJfr83+CDZyYP/VGHDCthfrmd//l39P2wJhkuCDbbeKaElLGWvUt
 abnPf0buCRqMAJe7vh0GHCx7290nEh2IqyHR4AYRVhRaN7bfAXdZH9Xp6ZGT25Fz
 uORgUbGAyhd5Ics/7twE4qeOkfJ6fxwgXsOlx90EfgVYyDJ1sBHNx8Buo2z8Bl/2
 rwCsW49kU7yX/wp11sJctR72RuLKC23dxS6z7aSWkRc6k3u+8xl2eeLIN59FNrKZ
 ToTdbXEQ
 =bdm2
 -----END PGP SIGNATURE-----

Merge tag 'irqchip-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core

Pull irqchip updates from Marc Zyngier:

- API updates:

  - Treewide conversion to generic_handle_domain_irq() for anything
    that looks like a chained interrupt controller

  - Update the irqdomain documentation

  - Use of bitmap_zalloc() throughout the tree

- New functionalities:

  - Support for GICv3 EPPI partitions

- Fixes:

  - Qualcomm PDC hierarchy fixes

  - Yet another priority decoding fix for the GICv3 pseudo-NMIs

  - Fix the apple-aic driver irq_eoi() callback to always unmask
    the interrupt

  - Properly handle edge interrupts on loongson-pch-pic

  - Let the mtk-sysirq driver advertise IRQCHIP_SKIP_SET_WAKE

Link: https://lore.kernel.org/r/20210828121013.2647964-1-maz@kernel.org
2021-08-29 21:19:50 +02:00
Marc Zyngier dbd1c54fc8 gpio: Bulk conversion to generic_handle_domain_irq()
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
2021-08-12 11:39:38 +01:00
Rasmus Villemoes ec7099fdea Revert "gpio: mpc8xxx: change the gpio interrupt flags."
This reverts commit 3d5bfbd971.

When booting with threadirqs, it causes a splat

  WARNING: CPU: 0 PID: 29 at kernel/irq/handle.c:159 __handle_irq_event_percpu+0x1ec/0x27c
  irq 66 handler irq_default_primary_handler+0x0/0x1c enabled interrupts

That splat later went away with commit 81e2073c17 ("genirq: Disable
interrupts for force threaded handlers"), which got backported to
-stable. However, when running an -rt kernel, the splat still
exists. Moreover, quoting Thomas Gleixner [1]

  But 3d5bfbd971 ("gpio: mpc8xxx: change the gpio interrupt flags.")
  has nothing to do with that:

      "Delete the interrupt IRQF_NO_THREAD flags in order to gpio interrupts
       can be threaded to allow high-priority processes to preempt."

  This changelog is blatantly wrong. In mainline forced irq threads
  have always been invoked with softirqs disabled, which obviously
  makes them non-preemptible.

So the patch didn't even do what its commit log said.

[1] https://lore.kernel.org/lkml/871r8zey88.ffs@nanos.tec.linutronix.de/

Cc: stable@vger.kernel.org # v5.9+
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2021-07-18 14:52:30 +02:00
Ran Wang 76c47d1449 gpio: mpc8xxx: Add ACPI support
Current implementation only supports DT, now add ACPI support.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2021-05-05 16:07:41 +02:00
Michael Walle 3795d7cc4f gpio: mpc8xxx: simplify ls1028a/ls1088a support
Some Layerscape/QoriQ SoCs have input buffers which needs to be enabled
first. This was done in two different ways in the driver. Unify it.

This was tested on a LS1028A SoC.

Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-09-30 10:50:30 +02:00
Song Hui 3d5bfbd971 gpio: mpc8xxx: change the gpio interrupt flags.
Delete the interrupt IRQF_NO_THREAD flags in order to gpio interrupts
can be threaded to allow high-priority processes to preempt.

Signed-off-by: Song Hui <hui.song_1@nxp.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-06-15 10:14:37 +02:00
Linus Walleij 6a77de2596 Linux 5.5-rc6
-----BEGIN PGP SIGNATURE-----
 
 iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl4bv/IeHHRvcnZhbGRz
 QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGKWEIAImoqyoGKU+ZcBPI
 PCrqWtNgrZvVDs/K/IinETZSwclvuQCJicN9DYu9g//3uxf9z+i4c5/Oq9veP1lw
 ikVjfwgo74SqNwO9L+78oUG+2rzUDwf/LTVhlqO17fxmT5WumJjC7Y6/TejwpOd5
 xmZ5NopLQTx95OJWaK0rrDUTkG1LzlQZINGbu1K8sRpbppcSc31Egh2n09kaOnmn
 6xRRuxFnk2dXuCCdcCdb6rW1vNzd1IRbPjqAktRCalp04hzIFDgXbj9pfOl/iu6O
 nl+xDSwziW3DzKxdkw3WZTYbPPK8e7s16qF23QLVgwlIKE0qL1h6uiEnAMARGfLm
 bVFIUbo=
 =Tdp+
 -----END PGP SIGNATURE-----

Merge tag 'v5.5-rc6' into devel

Linux 5.5-rc6
2020-01-17 08:59:29 +01:00
Song Hui 227caae52b gpio: mpc8xxx: ls1088a/ls1028a edge detection mode bug fixs.
On these boards, the irq_set_type must point one valid function pointer
that can correctly set both edge and falling edge.

Signed-off-by: Song Hui <hui.song_1@nxp.com>
Link: https://lore.kernel.org/r/20191122061839.24904-1-hui.song_1@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-01-07 13:37:11 +01:00
Johnson CH Chen (陳昭勳) 322f6a3182 gpio: mpc8xxx: Add platform device to gpiochip->parent
Dear Linus Walleij,

In old kernels, some APIs still try to use parent->of_node from struct gpio_chip,
and it could be resulted in kernel panic because parent is NULL. Adding platform
device to gpiochip->parent can fix this problem.

Signed-off-by: Johnson Chen <johnsonch.chen@moxa.com>
Link: https://patchwork.kernel.org/patch/11234609
Link: https://lore.kernel.org/r/HK0PR01MB3521489269F76467DFD7843FFA450@HK0PR01MB3521.apcprd01.prod.exchangelabs.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-12-09 14:38:03 +01:00
Russell King 787b64a43f gpio/mpc8xxx: fix qoriq GPIO reading
Qoriq requires the IBE register to be set to enable GPIO inputs to be
read.  Set it.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1iX3HC-00069N-0T@rmk-PC.armlinux.org.uk
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-11-21 14:30:08 +01:00
Vladimir Oltean 4e50573f39 gpio: mpc8xxx: Don't overwrite default irq_set_type callback
The per-SoC devtype structures can contain their own callbacks that
overwrite mpc8xxx_gpio_devtype_default.

The clear intention is that mpc8xxx_irq_set_type is used in case the SoC
does not specify a more specific callback. But what happens is that if
the SoC doesn't specify one, its .irq_set_type is de-facto NULL, and
this overwrites mpc8xxx_irq_set_type to a no-op. This means that the
following SoCs are affected:

- fsl,mpc8572-gpio
- fsl,ls1028a-gpio
- fsl,ls1088a-gpio

On these boards, the irq_set_type does exactly nothing, and the GPIO
controller keeps its GPICR register in the hardware-default state. On
the LS1028A, that is ACTIVE_BOTH, which means 2 interrupts are raised
even if the IRQ client requests LEVEL_HIGH. Another implication is that
the IRQs are not checked (e.g. level-triggered interrupts are not
rejected, although they are not supported).

Fixes: 82e39b0d85 ("gpio: mpc8xxx: handle differences between incarnations at a single place")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20191115125551.31061-1-olteanv@gmail.com
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-11-21 14:28:32 +01:00
Song Hui 698b8eeaed gpio/mpc8xxx: change irq handler from chained to normal
More than one gpio controllers can share one interrupt, change the
driver to request shared irq.

While this will work, it will mess up userspace accounting of the number
of interrupts per second in tools such as vmstat.  The reason is that
for every GPIO interrupt, /proc/interrupts records the count against GIC
interrupt 68 or 69, as well as the GPIO itself.  So, for every GPIO
interrupt, the total number of interrupts that the system has seen
increments by two.

Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Link: https://lore.kernel.org/r/20191011005643.41007-1-hui.song_1@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-10-16 14:09:50 +02:00
Song Hui 7b732209eb gpio: mpc8xxx: add ls1088a platform special function
ls1028a and ls1088a platform share common special function.
The gpio hardware what they use is the same version.

Signed-off-by: Song Hui <hui.song_1@nxp.com>
Link: https://lore.kernel.org/r/20190808101628.36782-3-hui.song_1@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-08-23 09:38:06 +02:00
Song Hui bd4bd33703 gpio: mpc8xxx: Add ls1028a device specify function.
There is a device specify register(named GPIO_IBE)
on ls1028a need to enable in initial stage.

Signed-off-by: Song Hui <hui.song_1@nxp.com>
Link: https://lore.kernel.org/r/20190718094902.15562-2-hui.song_1@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-08-03 00:15:03 +02:00
Linus Walleij b3222f7147 gpio: mpc8xxx: Do not reverse bits using bgpio
The MPC8xxx driver is always instantiating its generic GPIO functions
with the flag BGPIOF_BIG_ENDIAN. This means "big-endian bit order"
and means the bits representing the GPIO lines in the registers are
reversed around 31 bits so line 0 is at bit 31 and so forth down to
line 31 in bit 0.

Instead of looping into the generic MMIO gpio to do the simple
calculation of a bitmask, through a vtable call with two parameters
likely using stack frames etc (unless the compiler optimize it)
and obscuring the view for the programmer, let's just open-code
what the call does. This likely executes faster, saves space and
makes the code easier to read.

Cc: Liu Gang <Gang.Liu@nxp.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-10-25 11:25:40 +02:00
Rob Herring 7eb6ce2f27 gpio: Convert to using %pOF instead of full_name
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Tien Hock Loh <thloh@altera.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-14 15:01:12 +02:00
Liu Gang d71cf15b86 gpio: mpc8xxx: Correct irq handler function
From the beginning of the gpio-mpc8xxx.c, the "handle_level_irq"
has being used to handle GPIO interrupts in the PowerPC/Layerscape
platforms. But actually, almost all PowerPC/Layerscape platforms
assert an interrupt request upon either a high-to-low change or
any change on the state of the signal.

So the "handle_level_irq" is not reasonable for PowerPC/Layerscape
GPIO interrupt, it should be "handle_edge_irq". Otherwise the system
may lost some interrupts from the PIN's state changes.

Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-10-24 02:20:40 +02:00
Axel Lin adf32eaa05 gpio: mpc8xxx: Slightly update the code for better readability
Setting gc->direction_output to gc->direction_output looks strange.
I think this change makes the intention more clear.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-03-09 10:44:13 +07:00
Axel Lin cd0d3f58a0 gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
*read_reg and *write_reg can be removed because at all the places to call
them, we can just use gc->read_reg/gc->write_reg instead.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-03-09 10:43:09 +07:00
Axel Lin fa4007ca06 gpio: mpc8xxx: Fixup setting gpio direction output
For devtype with specific gpio_dir_out implementation, current code is
wrong because below code sets both gc->direction_output and
mpc8xxx_gc->direction_output to the same function.

gc->direction_output = devtype->gpio_dir_out ?: gc->direction_output;
mpc8xxx_gc->direction_output = gc->direction_output;

Set mpc8xxx_gc->direction_output = gc->direction_output first to fix it.
This way mpc8xxx_gc->direction_output actually calls the standard
bgpio_dir_out() to update register.

Fixes: commit 42178e2a1e ("drivers/gpio: Switch gpio-mpc8xxx to use gpio-generic")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-03-09 10:41:23 +07:00
Liu Gang 42178e2a1e drivers/gpio: Switch gpio-mpc8xxx to use gpio-generic
The new Layerscape platforms has the same ip block/controller
as GPIO on PowerPC platforms(MPC8XXX), but the GPIO registers
may be big or little endian. So the code needs to get the
endian property from DTB, then make additional functions to
fit all the PowerPC/Layerscape GPIO register read/write
operations.

gpio-generic.c provides an universal infrastructure for both
big and little endian register operations. So switch the
gpio-mpc8xxx to use gpio-generic can simplify the driver and
reduce a lot of code.

The IRQ and some workaround parts in gpio-mpc8xxx.c will be
updated with the new API interfaces but following the
original functionalities.

Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-08 18:32:58 +01:00
Guenter Roeck 78179989a0 gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
Commit 709d71a17c ("gpio: mpc8xxx: use gpiochip data pointer") replaces
the use of container_of() with gpiochip_get_data(). However, the data
pointer is not yet set by the time the save_regs function is called.

Fixes: 709d71a17c ("gpio: mpc8xxx: use gpiochip data pointer")
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-01-13 10:22:23 +01:00
Linus Walleij 709d71a17c gpio: mpc8xxx: use gpiochip data pointer
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-01-05 11:21:09 +01:00
Linus Walleij c759174e73 gpio: mpc8xxx: Be sure to clamp return value
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-26 22:28:16 +01:00
Thomas Gleixner bd0b9ac405 genirq: Remove irq argument from irq flow handlers
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.

Remove the argument.

Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
2015-09-16 15:47:51 +02:00
Alexander Stein 505936131e gpio: mpc8xxx: Convert mpc8xxx_gpio_chip.lock to raw_spinlock
mpc8xxx_gpio_chip.lock needs to be a real spinlock in preempt-rt.
Especially the interrupt related functions can not be converted to a
sleeping lock.

Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-07-28 14:40:11 +02:00
Uwe Kleine-König 0ba69e0898 gpio: mpc8xxx: add support for MPC5125
The gpio controller on MPC5125 is identical to the MPC5121 register
wise, the only difference is that the lines 0..3 are input only instead
of 28..31 on MPC5121.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-07-27 13:52:02 +02:00
Uwe Kleine-König 82e39b0d85 gpio: mpc8xxx: handle differences between incarnations at a single place
The gpio controllers that are handled by the mpc8xxx driver differ
slightly. Up to now some differences were handled by use of
of_device_is_compatible, others by use of struct of_device_id's data.

To make this consistent and easily extendable handle the differences at
a single place.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-07-27 12:21:56 +02:00
Uwe Kleine-König 4183afefd9 gpio: mpc8xxx: constify of_device_id
This variable is not modified in the driver and all functions it it
passed to don't change it either. So it can and should be marked const.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-07-27 12:20:28 +02:00
Thomas Gleixner 05379818e4 gpio/mpc8xxx: Consolidate chained IRQ handler install/remove
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.

Search and conversion was done with coccinelle:

Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
2015-07-14 12:12:19 +02:00
Krzysztof Kozlowski 0b354dc433 gpio: Constify irq_domain_ops
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-05-06 15:33:48 +02:00
Kevin Hao 32c006a997 gpio: mpc8xxx: remove __initdata annotation for mpc8xxx_gpio_ids[]
Since commit 98686d9a52 ("gpio: mpc8xxx: Convert to platform device
interface"), we get the following section mismatch warning. Remove the
__initdata annotation to fix it.
  WARNING: vmlinux.o(.data+0xbc28): Section mismatch in reference from the variable mpc8xxx_plat_driver to the variable .init.data:mpc8xxx_gpio_ids
  The variable mpc8xxx_plat_driver references
  the variable __initdata mpc8xxx_gpio_ids
  If the reference is valid then annotate the
  variable with __init* or __refdata (see linux/init.h) or name the variable:
  *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console

Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-05 10:51:35 +01:00
Ricardo Ribalda Delgado 257e10752c gpio: mpc8xxx: Use of_mm_gpiochip_remove
Since d621e8bae5 (Create of_mm_gpiochip_remove), there is a
counterpart for of_mm_gpiochip_add.

This patch implements the remove function of the driver making use of
it.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-01-21 17:45:11 +01:00
Ricardo Ribalda Delgado 98686d9a52 gpio: mpc8xxx: Convert to platform device interface.
This way we do not need to transverse the device tree manually.

Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-01-20 11:19:01 +01:00
Rojhalat Ibrahim e5db3b338a gpio-mpc8xxx: add mpc8xxx_gpio_set_multiple function
Add a set_multiple function to the MPC8xxx GPIO chip driver and thereby allow
for actual performance improvements when setting multiple outputs
simultaneously. In my case the time needed to configure an FPGA goes down from
48 s to 20 s.

Change log:
  v6: - rebase on current linux-gpio devel branch
  v5: - no change
  v4: - change interface of the set_multiple driver function to use
        unsigned long as type for the bit fields
      - use generic bitops (which also use unsigned long for bit fields)
  v3: - change commit message
  v2: - add this patch (v1 included only changes to gpiolib)

Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-27 15:01:18 +01:00
Liu Gang 1aeef303b5 powerpc/gpio: Fix the wrong GPIO input data on MPC8572/MPC8536
For MPC8572/MPC8536, the status of GPIOs defined as output
cannot be determined by reading GPDAT register, so the code
use shadow data register instead. But the code may give the
wrong status of GPIOs defined as input under some scenarios:

1. If some pins were configured as inputs and were asserted
high before booting the kernel, the shadow data has been
initialized with those pin values.
2. Some pins have been configured as output first and have
been set to the high value, then reconfigured as input.

The above cases will make the shadow data for those input
pins to be set to high. Then reading the pin status will
always return high even if the actual pin status is low.

The code should eliminate the effects of the shadow data to
the input pins, and the status of those pins should be
read directly from GPDAT.

Cc: stable@vger.kernel.org
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-12-03 13:10:48 +01:00
Linus Torvalds 10d0c9705e DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
 
 - Cross arch clean-up and consolidation of early DT scanning code.
 - Clean-up and removal of arch prom.h headers. Makes arch specific
   prom.h optional on all but Sparc.
 - Addition of interrupts-extended property for devices connected to
   multiple interrupt controllers.
 - Refactoring of DT interrupt parsing code in preparation for deferred
   probe of interrupts.
 - ARM cpu and cpu topology bindings documentation.
 - Various DT vendor binding documentation updates.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
 R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
 huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
 PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
 2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
 Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
 =GCbY
 -----END PGP SIGNATURE-----

Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

Pull devicetree updates from Rob Herring:
 "DeviceTree updates for 3.13.  This is a bit larger pull request than
  usual for this cycle with lots of clean-up.

   - Cross arch clean-up and consolidation of early DT scanning code.
   - Clean-up and removal of arch prom.h headers.  Makes arch specific
     prom.h optional on all but Sparc.
   - Addition of interrupts-extended property for devices connected to
     multiple interrupt controllers.
   - Refactoring of DT interrupt parsing code in preparation for
     deferred probe of interrupts.
   - ARM cpu and cpu topology bindings documentation.
   - Various DT vendor binding documentation updates"

* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
  powerpc: add missing explicit OF includes for ppc
  dt/irq: add empty of_irq_count for !OF_IRQ
  dt: disable self-tests for !OF_IRQ
  of: irq: Fix interrupt-map entry matching
  MIPS: Netlogic: replace early_init_devtree() call
  of: Add Panasonic Corporation vendor prefix
  of: Add Chunghwa Picture Tubes Ltd. vendor prefix
  of: Add AU Optronics Corporation vendor prefix
  of/irq: Fix potential buffer overflow
  of/irq: Fix bug in interrupt parsing refactor.
  of: set dma_mask to point to coherent_dma_mask
  of: add vendor prefix for PHYTEC Messtechnik GmbH
  DT: sort vendor-prefixes.txt
  of: Add vendor prefix for Cadence
  of: Add empty for_each_available_child_of_node() macro definition
  arm/versatile: Fix versatile irq specifications.
  of/irq: create interrupts-extended property
  microblaze/pci: Drop PowerPC-ism from irq parsing
  of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
  of/irq: Use irq_of_parse_and_map()
  ...
2013-11-12 16:52:17 +09:00
Linus Walleij 5ba17ae9b8 gpio: mpc8xxx: drop references to "virtual" IRQ
Rename the argument "virq" to just "irq", this IRQ isn't any
more "virtual" than any other Linux IRQ number, we use "hwirq"
for the actual hw-numbers, "virq" is just bogus.

Cc: Anatolij Gustschin <agust@denx.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-10-16 09:59:52 +02:00
Rob Herring 5af5073004 drivers: clean-up prom.h implicit includes
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
2013-10-09 20:04:04 -05:00
Anatolij Gustschin de0ccf7881 gpio: mpc8xxx: don't set IRQ_TYPE_NONE when creating irq mapping
Exporting gpios over sysfs GPIO interface throws genirq
error messages, i.e. on an mpc5121 based board exporting
GPIO 5 triggers it:

    # echo 229 > /sys/class/gpio/export
    genirq: Setting trigger mode 0 for irq 44 failed
    (mpc512x_irq_set_type+0x0/0x18c)

Similar error messages appear in the kernel boot log since the
board specifies GPIOs for matrix keypad and also SD Card write
protect and card detect GPIOs in its device tree. For all these
GPIOs there is an error message in the log.

The issue is triggered by setting the irq type to IRQ_TYPE_NONE
in the driver's irq_domain map function mpc8xxx_gpio_irq_map().

...
  mpc8xxx_gpio_irq_map
    irq_set_irq_type
      __irq_set_trigger

__irq_set_trigger() calls irq_set_type() callback of the mpc8xxx gpio
irq chip with the IRQ_TYPE_NONE in its 'flags' argument. This callback
is either mpc8xxx_irq_set_type() or mpc512x_irq_set_type(). Both these
functions return -EINVAL in the case if IRQ_TYPE_NONE is passed in the
flow_type argument. This return value triggers the observed error
message in __irq_set_trigger(). Modifying these callbacks to not
return an error in IRQ_TYPE_NONE case doesn't make any sense to me.
The line setting IRQ_TYPE_NONE type has been originally added by
commit 345e5c8a "powerpc: Add interrupt support to mpc8xxx_gpio".
At this time set_irq_type() checked its type argument and returned 0
if the type argument didn't specify any meaningful type in its type
sense bits (and thus was equal to IRQ_TYPE_NONE). Effectively this
line was a nop and I wonder what was the point of adding it.

Remove IRQ_TYPE_NONE setting in the irq_domain mapping function.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-02-04 21:41:46 +01:00