clk_get() returns an error pointer, or a valid token to pass back to the
clock API. Hence, the result must be checked with IS_ERR(), not by
comparison against NULL.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
fix a trivial copy'n'paste error in the regmap kerneldoc, s/write/read/
for the regmap_read(), regmap_raw_read() and regmap_bulk_read() routines
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add basic support for the System Power Management Interface (SPMI) bus.
This is a simple implementation which only implements register accesses
via the Extended Register Read/Write Long commands.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
If called early enough, regmap_debugfs_init causes a crash, if the
fs subsystem does not have its mount cache created yet. Even if this
would work, the root node for the regmap debugfs is still missing,
thus postpone the regmap_debugfs_init in this case until the root
node is created. A special regmap_debugfs_early list is created for
this purpose which is parsed later in the boot.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
clear the status bit if the mask register doesn't prevent
the chip level irq from being asserted
OR in the following sequence, there will be irq storm happens:
1) interrupt is triggered;
2) another thread disables it(the mask bit is set);
3) _Then_ the interrupt thread is not ACKed(the status bit is not cleared),
and it's ignored;
4) if the irq is still asserted because of the uncleared status bit,
the irq storm happens;
Signed-off-by: Yi Zhang <yizhang@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Extend the interface for async I/O by allowing the value buffer to be
omitted and sending the value as part of the register buffer, minimising
the number of separate hardware operations required.
Signed-off-by: Mark Brown <broonie@linaro.org>
If the value is zero then assume it has been included in the register data
and don't send anything, minimising the number of interactions with the
hardware.
Signed-off-by: Mark Brown <broonie@linaro.org>
New API regmap_multi_reg_write() is defined that allows a set of reg,val
pairs to be written to a I2C client device as one block transfer from the
point of view of a single I2C master system.
A simple demonstration implementation is included that just splits the
block write request into a sequence of single register writes.
The implementation will be modified later to support those I2C clients
that implement the alternative non-standard MULTIWRITE block write mode
so to achieve a single I2C transfer that will be atomic even in multiple
I2C master systems.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Try to speed up I/O a little by not synchronising until we are finished
scheduling writes. A brief survey of existing users suggests we have none
that would currently benefit from an async cache sync.
Signed-off-by: Mark Brown <broonie@linaro.org>
When regmap_bulk_write() is called with the map->use_single_rw flag set
an immediate mutex deadlock happens because regmap_raw_write() is called
after obtaining the mutex and regmap_raw_write() itself then tries to
obtain the mutex as well.
It is obvious that no one other than myself tried it with a real device.
I did, but only for the purposes of an experiment and demonstration.
But even if this situation will never ever happen with a real device, it
is a bug and therefore should be fixed.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make it easier for drivers to include single register writes in
asynchronous sequences by providing async versions of the write
and update bits operations. The update bits operations are only
likely to be effective when used with devices that have caches
but this is common enough to be useful.
Signed-off-by: Mark Brown <broonie@linaro.org>
Rather than passing a flag around through the entire call stack store it
in the regmap struct and read it when required. This minimises the
visibility of the feature through the API, minimising the code updates
needed to use it more widely.
Signed-off-by: Mark Brown <broonie@linaro.org>
Since it is quite common for single register raw or async writes to be
generated by rbtree cache syncs or firmware downloads and essentially all
hardware will be faster with only a single transfer optimise this case by
copying single values into the internal scratch buffer before sending.
Signed-off-by: Mark Brown <broonie@linaro.org>
Rather than allocating and deallocating the structures used to manage async
transfers each time we do one keep the structures around as long as the
regmap is around. This should provide a small performance improvement.
Signed-off-by: Mark Brown <broonie@linaro.org>
Current Linux kernel is supporting regmap_field method
and it is very useful feature.
It needs one regmap_filed for one register access.
OTOH, there is multi port device which
has many same registers in the market.
The difference for each register access is
only its address offset.
Current API needs many regmap_field for such device,
but it is not good.
This patch adds new regmap_fileds API which can care
about multi port/offset access via regmap.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current regmap_field is supporting read/write functions.
This patch adds new update_bits function for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlIPcACgkQMUfUDdst+ynUMwCaAnITsxyDXYQ4DqEsz8EcOtMk
718AoLrgnUZs3B+70AT34DVktg4HSThk
=USl9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
A quiet release for regmap, some cleanups, fixes and:
- Improved node coalescing for rbtree, reducing memory usage and
improving performance during syncs.
- Support for registering multiple register patches.
- A quirk for handling interrupts that need to be clear when masked
in regmap-irq.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=um4f
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"A quiet release for regmap, some cleanups, fixes and:
- Improved node coalescing for rbtree, reducing memory usage and
improving performance during syncs.
- Support for registering multiple register patches.
- A quirk for handling interrupts that need to be clear when masked
in regmap-irq"
* tag 'regmap-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: rbtree: Make cache_present bitmap per node
regmap: rbtree: Reduce number of nodes, take 2
regmap: rbtree: Simplify adjacent node look-up
regmap: debugfs: Fix continued read from registers file
regcache-rbtree: Fix reg_stride != 1
regmap: Allow multiple patches to be registered
regmap: regcache: allow read-only regs to be cached
regmap: fix regcache_reg_present() for empty cache
regmap: core: allow a virtual range to cover its own data window
regmap: irq: document mask/wake_invert flags
regmap: irq: make flags bool and put them in a bitfield
regmap: irq: Allow to acknowledge masked interrupts during initialization
regmap: Provide __acquires/__releases annotations
With devices which have a dense and small register map but placed at a large
offset the global cache_present bitmap imposes a huge memory overhead. Making
the cache_present per rbtree node avoids the issue and easily reduces the memory
footprint by a factor of ten. For devices with a more sparse map or without a
large base register offset the memory usage might increase slightly by a few
bytes, but not significantly. E.g. for a device which has ~50 registers at
offset 0x4000 the memory footprint of the register cache goes down form 2496
bytes to 175 bytes.
Moving the bitmap to a per node basis means that the handling of the bitmap is
now cache implementation specific and can no longer be managed by the core. The
regcache_sync_block() function is extended by a additional parameter so that the
cache implementation can tell the core which registers in the block are set and
which are not. The parameter is optional and if NULL the core assumes that all
registers are set. The rbtree cache also needs to implement its own drop
callback instead of relying on the core to handle this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Support for reducing the number of nodes and memory consumption of the rbtree
cache by allowing for small unused holes in the node's register cache block was
initially added in commit 0c7ed856 ("regmap: Cut down on the average # of nodes
in the rbtree cache"). But the commit had problems and so its effect was
reverted again in commit 4e67fb5 ("regmap: rbtree: Fix overlapping rbnodes.").
This patch brings the feature back of reducing the average number of nodes,
which will speedup node look-up, while at the same time also reducing the memory
usage of the rbtree cache. This patch takes a slightly different approach than
the original patch though. It modifies the adjacent node look-up to not only
consider nodes that are just one to the left or the right of the register but
any node that falls in a certain range around the register. The range is
calculated based on how much memory it would take to allocate a new node
compared to how much memory it takes adding a set of unused registers to an
existing node. E.g. if a node takes up 24 bytes and each register in a block
uses 1 byte the range will be from the register address - 24 to the register
address + 24. If we find a node that falls within this range it is cheaper or as
expensive to add the register to the existing node and have a couple of unused
registers in the node's cache compared to allocating a new node.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
A register which is adjacent to a node will either be left to the first
register or right to the last register. It will not be within the node's range,
so there is no point in checking for each register cached by the node whether
the new register is next to it. It is sufficient to check whether the register
comes before the first register or after the last register of the node.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The regmap_debugfs_get_dump_start() function maps from a file offset to the
register that can be found at that position in the file. This is done using a
look-up table. Commit d6814a7d ("regmap: debugfs: Suppress cache for partial
register files") added a check to bypass the look-up table for partial register
files, since the offsets in that table are only correct for the full register
file. The check incorrectly uses the file offset instead of the register base
address and returns it. This will cause the file offset to be interpreted as a
register address which will result in a incorrect output from the registers file
for all reads except at position 0.
The issue can easily be reproduced by doing small reads the registers file, e.g.
`dd if=registers bs=10 count=5`.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
There are a couple of calculations, which convert between register addresses and
block indices, in regcache_rbtree_sync() and regcache_rbtree_node_alloc() which
assume that reg_stride is 1. This will break the rb cache for configurations
which do not use a reg_stride of 1.
Also rename 'base' in regcache_rbtree_sync() to 'start' to avoid confusion with
'base_reg'.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Avoid overlapping register regions by making the initial blklen of a new
node 1. If a register write occurs to a yet uncached register, that is
lower than but near an existing node's base_reg, a new node is created
and it's blklen is set to an arbitrary value (sizeof(*rbnode)). That may
cause this node to overlap with another node. Those nodes should be merged,
but this merge doesn't happen yet, so this patch at least makes the initial
blklen small enough to avoid hitting the wrong node, which may otherwise
lead to severe breakage.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
It may be useful to register multiple patches with regmap, for example
one that depends on the device revision and one that depends on the system
configuration. Add support for doing this, appending any new patches to
the existing patches.
Signed-off-by: Mark Brown <broonie@linaro.org>
The regmap_writeable() check should not be done in
regcache_write() because this prevents read-only
registers to be cached. After a read on a read-only
register its value will not be stored in the cache
and the next time someone will try to read it the
value will be read from the bus instead of the
cache.
Instead the regmap_writeable() check should be done
in _regmap_write() to prevent callers from writing
to read-only registers.
Signed-off-by: Ionut Nicu <ioan.nicu.ext@nsn.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the initial case when no reg_defaults values are
provided and no register value was added to the cache
yet, the cache_present bitmap is NULL. If this function
is invoked for any register it should return false
(i.e. the register is not cached) instead of true.
Signed-off-by: Ionut Nicu <ioan.nicu.ext@nsn.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
I see no reason why a virtual range shouldn't be allowed to cover its
own data window if the page selection register is in the same place
on every page.
For chips which use paged access for all of their registers, but only
when connected via I2C, and which can access the whole register space
directly when connected via SPI, this allows to avoid acrobatics with
the register ranges by simply mapping the I2C ranges over the data
window beginning at 0x0, and then using linear access for the SPI
variant.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
regcache_sync_block_raw_flush() expects the address of the register after last
register that needs to be synced as its parameter. But the last call to
regcache_sync_block_raw_flush() in regcache_sync_block_raw() passes the address
of the last register in the block. This effectively always skips over the last
register in a block, even if it needs to be synced. In order to fix it increase
the address by one register.
The issue was introduced in commit 75a5f89 ("regmap: cache: Write consecutive
registers in a single block write").
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The usage of strict_strto*() is not preferred, because
strict_strto*() is obsolete. Thus, kstrto*() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the hardware interrupt mask register does not prevent the chip level
irq from being asserted by the corresponding interrupt status bit, already
set interrupt bits should to be cleared once after masking them during
initialization. Add a flag to let drivers enable this behavior.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following sparse warnings:
drivers/base/regmap/regmap.c:305:13: warning: context imbalance in 'regmap_lock_spinlock' - wrong count at exit
drivers/base/regmap/regmap.c:314:13: warning: context imbalance in 'regmap_unlock_spinlock' - unexpected unlock
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This fixes a crash if something tries to do an asynchronous operation on
busless maps which was introduced during the merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c5Gp
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"Fix regmap crash for async operation on busless maps
This fixes a crash if something tries to do an asynchronous operation
on busless maps which was introduced during the merge window"
* tag 'regmap-v3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: cache: bail in regmap_async_complete() for bus-less maps
Commit f8bd822cb ("regmap: cache: Factor out block sync") made
regcache_rbtree_sync() call regmap_async_complete(), which in turn does
not check for map->bus before dereferencing it.
This causes a NULL pointer dereference on bus-less maps.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: stable@vger.kernel.org [v3.10 only]
Signed-off-by: Mark Brown <broonie@linaro.org>
Mark Brown