In the suspend, the IRQ function will not work in some machines. So the JD
status should be checked in the resume function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a codec driver for the Everest ES8316, based on code provided by
David Yang from Everest Semi.
I limited the functionality to items where the vendor code was clear,
and things that can be tested on the Weibu F3C (Intel Cherry Trail).
As a result the initial implementation only supports running in slave
mode at single speed (up to 48kHz sample rate) using I2S. HPD is not
supported.
Signed-off-by: David Yang <yangxiaohua@everest-semi.com>
[drake@endlessm.com: significant cleanups and simplifications,
remove dead/unclear code]
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the startup function to count DAI instead of hw_params.
This change matches the number of opened DAIs.
If this change isn't applied, you may get unexpected error due to
mismatching of count. Since the excution number of hw_params and
shutdown may be different, the mismatching happens.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ryo Kodama <ryo.kodama.vz@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
struct snd_pcm_hw_constraint_list ratec is not used.
Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Very fast systems may violate the minimum constraints for time the reset
line needs to remain low, or communicate with the device too soon after
releasing the reset. Fix this by adding some delays in to allow the chip
to properly reset, also factor out the reset into a function as it is
likely it will be re-used in later additions to the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The list terminator is 0xbedead but the message warning if it
wasn't found was showing that 0xbeadead was expected.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC needs to know connected DAI ID for probing.
It is not a big problem if device/driver was only for sound,
but getting DAI ID will be difficult if device includes both
Video/Sound, like HDMI.
To solve this issue, this patch adds new .get_dai_id callback
on hdmi_codec_ops
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DesignWare HDMI driver (= dw-hdmi) is supporting HDMI sound, and its
probe function was calling sound binding function multiple times as
same HDMI device different port.
Because of this behavior, commit 9731f82d60 ("ASoC: hdmi-codec: enable
multi probe for ...") was added for multi detection case.
But, this DesignWare HDMI detection/bind code was exchanged/adjusted by
commit 69497eb923 ("drm: bridge: dw-hdmi: Implement DRM bridge...").
Now, all DesignWare HDMI sound ports are detected as 1 bindng function.
Because of this, hdmi-codec multi detection support is no longer needed.
Thus, this patch removes
commit 9731f82d60 ("ASoC: hdmi-codec: enable multi probe for ..."),
and its related
commit 340327a62c ("ASoC: hdmi-codec: Fix hdmi_of_xlate_dai_name...")
commit 8480ac5679 ("ASoC: hdmi-codec: remove HDMI device unregister")
commit 0c343a35bf ("ASoC: hdmi-codec: fix spelling mistake: ...)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function already defines a ret variable at the top and makes
no particular use of the shadowed definition, as such remove the
redundant definition.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The xinfo member of struct wm_coeff_ctl_ops is never used.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The shift member of struct soc_mixer_control is unsigned int.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the SRM lock check section of code the '&' bitwise operator is
used as part of checking lock status. Functionally the code works
as intended, but the conditional statement is a boolean comparison
so should really use '&&' logical operator instead. This commit
rectifies this discrepancy.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
Zero is a totally valid value to specify for the bst_ipk, as such we
should append CS35L35_VALID_PDATA to ensure that it actually makes it
into the register value.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the Boost Inductor parameters based off the size of the inductor
on the HW setup
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver now supports ACPI based initialisation as well as DT
and old pdata methods. However the FW data handling still uses
DT specific calls to read firmware data (of_property*) so for
ACPI based initialisation the FW data will only be set to default
values. This patch updates the FW handling to use device_property*
calls instead so that both ACPI and DT are handled as expected.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the ACPI match ID for rt5514 codec.
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings:
sound/soc/codecs/rt5665.c:4928:19: warning:
symbol 'rt5665_i2c_driver' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With gcc 4.1.2:
sound/soc/codecs/rt5665.c: In function ‘rt5665_i2s_pin_event’:
sound/soc/codecs/rt5665.c:2610: warning: ‘mask1’ may be used uninitialized in this function
sound/soc/codecs/rt5665.c:2610: warning: ‘val2’ may be used uninitialized in this function
sound/soc/codecs/rt5665.c:2610: warning: ‘val1’ may be used uninitialized in this function
The first one is currently a false positive, as rt5665_i2s_pin_event()
is never called with snd_soc_dapm_widget.shift set to a value not
handled by the switch() statement. But that may change, so
preinitialize mask1 to fix this, like is already done for mask2.
The last two are false-positives, the compiler is just not smart enough
to notice the mask and val variables are always used together.
Fixes: 9b5d3865b3 ("ASoC: rt5665: set i2s pin share configuration")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds more width and channels support in the TDM mode.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support TDM format for NAU88L24.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: John Hsu <supercraig0719@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A function snd_soc_update_bits() is an application of
regmap_update_bits_base(). This function takes some arguments for bitmask
and new value, thus the arguments should be a type which has width.
However bool is used to variable for the argument. This brings truncation
and results in invalid operation.
This commit fixes this bug by using unsigned int type, instead of bool.
This bug is detected by sparse:
smsm8916-wcd-analog.c:809:43: warning: odd constant _Bool cast (40 becomes 1)
smsm8916-wcd-analog.c:814:43: warning: odd constant _Bool cast (40 becomes 1)
Fixes: 585e881e5b ("ASoC: codecs: Add msm8916-wcd analog codec")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the SRM lock check section of code the '&' bitwise operator is
used as part of checking lock status. Functionally the code works
as intended, but the conditional statement is a boolean comparison
so should really use '&&' logical operator instead. This commit
rectifies this discrepancy.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Thinkpad Helix 2 is a tablet PC, the audio is powered by Core M
broadwell-audio and rt286 codec. For all versions of Linux kernel,
the stereo output doesn't work properly when earphones are plugged
in, the sound was coming out from both channels even if the audio
contains only the left or right channel. Furthermore, if a music
recorded in stereo is played, the two channels cancle out each other
out, as a result, no voice but only distorted background music can be
heard, like a sound card with builtin a Karaoke sount effect.
Apparently this tablet uses a combo jack with polarity incorrectly
set by rt286 driver. This patch adds DMI information of Thinkpad Helix 2
to force_combo_jack_table[] and the issue is resolved. The microphone
input doesn't work regardless to the presence of this patch and still
needs help from other developers to investigate.
This is my first patch to LKML directly, sorry for CC-ing too many
people here.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=93841
Signed-off-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Mark Brown <broonie@kernel.org>
Asymmetric audio interface formats exist in ak4613 by same
register settings.
Capture Playback
24bit LEFT_J 16bit RIGHT_J
24bit LEFT_J 20bit RIGHT_J
24bit LEFT_J 24bit RIGHT_J
24bit LEFT_J 24bit LEFT_J
24bit I2S 24bit I2S
These asymmetric formats makes driver / behavior difficult.
It is not HW limitation, but SW limitation. To makes code reading
easy, this patch removes asymmetric format support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
gcc-7 warns that there is a duplicate 'const' specifier in some
variables that are declared using the SOC_ENUM_SINGLE_DECL macro:
sound/soc/codecs/rt5665.c:915:14: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(rt5665_if1_1_01_adc_enum,
sound/soc/codecs/rt5665.c:918:14: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(rt5665_if1_1_23_adc_enum,
sound/soc/codecs/rt5665.c:921:14: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(rt5665_if1_1_45_adc_enum,
sound/soc/codecs/rt5665.c:924:14: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(rt5665_if1_1_67_adc_enum,
...
This removes one to fix the 68 warnings in this file
Fixes: 33ada14a26 ("ASoC: add rt5665 codec driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
gcc-7 warns that there is a duplicate 'const' specifier in some
variables that are declared using the SOC_ENUM_SINGLE_DECL macro:
sound/soc/codecs/rt5514.c:398:14: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(
sound/soc/codecs/rt5514.c:405:14: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(
This removes one to fix the warning.
Fixes: 4a6180ea73 ("ASoC: rt5514: add rt5514 codec driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Bitclk is derived from sysclk using bclk_divs.
Sysclk can be derived in two ways:
(1) directly from MLCK
(2) MCLK via PLL
Commit 3c01b9ee2a ("ASoC: codec: wm8960: Relax bit clock
computation")
relaxed bitclk computation when sysclk is directly derived from MCLK.
Lets do the same thing when sysclk is derived via PLL.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The new PLL configuration code triggers a harmless warning:
sound/soc/codecs/wm8960.c: In function 'wm8960_configure_clocking':
sound/soc/codecs/wm8960.c:735:3: error: 'best_freq_out' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
wm8960_set_pll(codec, freq_in, best_freq_out);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sound/soc/codecs/wm8960.c:699:12: note: 'best_freq_out' was declared
here
Fix this by reworking the code such that:
1) When there is no PLL freq available return -EINVAL and make
sure *bclk_idx, *dac_idx, *sysclk_idx are initialized with
invalid values.
2) When there is a PLL freq available initialize *bclk_idx,
*dac_idx and *sysclk_idx with correct values and immediately
return the freq available.
Fixes: 84fdc00d51 ("ASoC: codec: wm9860: Refactor PLL out freq search")
Fixes: 303e8954af ("ASoC: codec: wm8960: Stop when a matching PLL freq is found")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove initial configuration of Class D gain for 1R and 2L.
Leave them at the chip default.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: John Hsu <supercraig0719@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename the name of kcontrols to match up the DAPM
widget controls.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: John Hsu <supercraig0719@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During reset "refactoring" the output configuration was lost.
This commit repairs sound on EDB93XX boards.
Fixes: 9a397f4 ("ASoC: cs4271: add regulator consumer support")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org> # 4.6+
Add driver for NAU88L24.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: John Hsu <supercraig0719@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
tas2552_suspend() and tas2552_resume() currently always return success,
even though they may fail.
Fix this behaviour by always propagating the error code.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On the chip the IMON signal is a full 24-bits however normally only
some of the bits will be sent over the bus. The chip provides a field
to select which bits of the IMON will be sent back, this is the only
feedback signal that has this feature.
Add an additional entry to the cirrus,imon device tree property to
allow the IMON scale parameter to be passed.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct some minor errors in the register defaults.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Thinkpad Tablet tablet has a similar audio setup as the Intel Braswell
platform.
A quirk is needed to detect the platform and setup the platform data
properly:
Manufacturer: LENOVO
Product Name: 20C1CTO1WW
Version: ThinkPad 10
Manufacturer: LENOVO
Product Name: 20C3001VHH
Version: ThinkPad 10
Manufacturer: LENOVO
Product Name: 20C10024GE
Version: ThinkPad Tablet B
Manufacturer: LENOVO
Product Name: 20359
Version: Lenovo Miix 2 10
Signed-off-by: Nicole Faerber <nicole.faerber@id3p.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5514 can get confused and incorrectly detect a start bit if the
SCL/SDA lines happen to both go low and then high again. This
situation has been seen to happen at reboot time and is also
theoretically possible during suspend/resume if the rt5514 keeps power
but we shut down the i2c connection.
When this happens the rt5514 is confused about the state of the i2c
bus and won't recognize its own address. That will lead to the rt5514
incorrectly NAKing the first transfer.
A single i2c transfer to any address should be enough to get the
rt5514 out of this funky state.
It is currently believed that this problem should be fixed in the
rt5514 driver itself because it seems that the i2c controller in the
rt5514 is easily confused. Most i2c devices wouldn't detect a start
bit in this case.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In rt5514_i2c_probe() if the regmap_read(RT5514_VENDOR_ID2) fails then
"val" may be left as uninitialized. Current code relies on "val" not
being RT5514_DEVICE_ID, but that's potentially unsafe.
Let's check for errors from regmap_read() and also explicitly init the
value do we're not passing a possibly uninitialized int to printk.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There's no reason for rt5514_i2c_driver to be non-static.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the case of error in tas2552_codec_probe() we should better
propagate the real error code instead of always returning '-EIO'.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now, we can use .set_jack callback function on codec level. So we
don't need export rt5665_set_jack_detect.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce the "lrclk-strength" property to allow LRCLK pad drive strength
to be changed via device tree.
When running a stress playback loop test on a mx6dl wandboard channel
swap can be noticed on about 10% of the times.
While debugging this issue I noticed that when probing the SGTL5000
LRCLK pin with the scope the swap did not happen. After removing
the probe the swap started to happen again.
After changing the LRCLK pad drive strength to the maximum value the
issue is gone.
Same fix works on a mx6dl Colibri board as well.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using an external boost supply the PDN_DONE bit is not set, update
the handling in this case to use to use an appropriate fixed delay.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Shorten the time it takes to power down the amp by disabling the volume
ramp whilst doing the final shutdown. The driver has already muted the
amplifier at this stage so doing the volume ramp serves no purpose.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When a matching PLL freq is found, searching continues even this is
not necessary. The problem was introduced with the following refactoring
commit 84fdc00d51 ("ASoC: codec: wm9860: Refactor PLL out freq search)
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a separate function for deriving (sysclk, lrclk, bclk)
when the clock is auto or pll.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-rt5677.ko | grep alias
alias: i2c:RT5677CE:00
alias: i2c:rt5676
alias: i2c:rt5677
After this patch:
$ modinfo sound/soc/codecs/snd-soc-rt5677.ko | grep alias
alias: of:N*T*Crealtek,rt5677C*
alias: of:N*T*Crealtek,rt5677
alias: i2c:RT5677CE:00
alias: i2c:rt5676
alias: i2c:rt5677
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-wm8978.ko | grep alias
alias: i2c:wm8978
After this patch:
$ modinfo sound/soc/codecs/snd-soc-wm8978.ko | grep alias
alias: i2c:wm8978
alias: of:N*T*Cwlf,wm8978C*
alias: of:N*T*Cwlf,wm8978
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-uda1380.ko | grep alias
alias: i2c:uda1380
After this patch:
$ modinfo sound/soc/codecs/snd-soc-uda1380.ko | grep alias
alias: of:N*T*Cnxp,uda1380C*
alias: of:N*T*Cnxp,uda1380
alias: i2c:uda1380
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-sta529.ko | grep alias
alias: i2c:sta529
After this patch:
$ modinfo sound/soc/codecs/snd-soc-sta529.ko | grep alias
alias: of:N*T*Cst,sta529C*
alias: of:N*T*Cst,sta529
alias: i2c:sta529
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-ssm4567.ko | grep alias
alias: acpi*:INT343B:*
alias: i2c:ssm4567
After this patch:
$ modinfo sound/soc/codecs/snd-soc-ssm4567.ko | grep alias
alias: acpi*:INT343B:*
alias: of:N*T*Cadi,ssm4567C*
alias: of:N*T*Cadi,ssm4567
alias: i2c:ssm4567
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-rt5645.ko | grep alias
alias: acpi*:10EC3270:*
alias: acpi*:10EC5640:*
alias: acpi*:10EC5650:*
alias: acpi*:10EC5648:*
alias: acpi*:10EC5645:*
alias: i2c:rt5650
alias: i2c:rt5645
After this patch:
$ modinfo sound/soc/codecs/snd-soc-rt5645.ko | grep alias
alias: of:N*T*Crealtek,rt5650C*
alias: of:N*T*Crealtek,rt5650
alias: of:N*T*Crealtek,rt5645C*
alias: of:N*T*Crealtek,rt5645
alias: acpi*:10EC3270:*
alias: acpi*:10EC5640:*
alias: acpi*:10EC5650:*
alias: acpi*:10EC5648:*
alias: acpi*:10EC5645:*
alias: i2c:rt5650
alias: i2c:rt5645
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver has an OF device ID table but the struct i2c_driver
.of_match_table field is not set.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
While there, move the MODULE_DEVICE_TABLE(i2c, max9867_i2c_id) just next
to the I2C device table declaration, for consistency with other drivers.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-max9867.ko | grep alias
alias: i2c:max9867
After this patch:
$ modinfo sound/soc/codecs/snd-soc-max9867.ko | grep alias
alias: i2c:max9867
alias: of:N*T*Cmaxim,max9867C*
alias: of:N*T*Cmaxim,max9867
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Newer ADSP2V2 codecs include a memory protection unit that can
be set to trap illegal accesses. When enabling an ADSPV2 core we
must configure the memory region traps so that the firmware can
access its own memory.
Signed-off-by: Mayuresh Kulkarni <mkulkarni@opensource.wolfsonmicro.com>
Signed-off-by: Nikesh Oswal <Nikesh.Oswal@wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adds support for ADSP2V2 cores. Primary differences are that
they use a 32-bit register map compared to the 16-bit register
map of ADSP2V1, and there are some changes to clocking control.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The new controls will give user the ability to route the left PDM channel
data to the right headset/handsfree DAC.
HS mono to stereo switch: PDM channel 1 (or mono) data to both HS DAC.
HF mono to stereo switch: PDM channel 3 data to both HF DAC.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When creating the codec dai, use sig_bits to update the max bps based
on the codec capability. So both the link DMA and codec format will be
calculated based on DAI sig_bits.
So update the sig_bits with converter capability and use the sig_bits
for HDA format calculation.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The error path in probe attempts to put the device back into reset.
Should we fail to get the reset_gpio (such as a probe defer) we will
leave the error value in there, which the gpiod_set_value_cansleep on
the error path will attempt to deference.
Fix this issue by clearing reset_gpio before we head into the error
path.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
WM8960 derives bit clock from sysclock using BCLKDIV[3:0] of R8
clocking register (See WM8960 datasheet, page 71).
There are use cases, like this:
aplay -Dhw:0,0 -r 48000 -c 1 -f S20_3LE -t raw audio48k20b_3LE1c.pcm
where no BCLKDIV applied to sysclock can give us the exact requested
bitclk, so driver fails to configure clocking and aplay fails to run.
Fix this by relaxing bitclk computation, so that when no exact value
can be derived from sysclk pick the closest value greater than
expected bitclk.
Suggested-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a separate function for finding (sysclk, lrclk, bclk)
when the clock is auto or mclk. This makes code easier to
read and reduces the indentation level in wm8960_configure_clocking.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pre divider control register of IF1 and IF2/3 are different.
The driver used the same register for all interfaces which was a
mistake.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The shift is RT5665_IF2_1_ADC_IN_SFT not RT5665_IF3_ADC_IN_SFT.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM8903 has four different voltage inputs: AVDD, CPVDD, DBVDD
and DCVDD. On the Qualcomm APQ8060 Dragonboard these are all
supplied from proper regulators and thus need activating and
binding.
This is a quick-and-dirty solution just grabbing and enabling the
regulator supplies on probe() and disabling them on remove() and
the errorpath. More elaborate power management is likely possible.
I assume the nVidia designs using this codec have some hard-wired
always-on power and will be happy with using the dummy regulators
for this. But someone from the nVidia camp should probably check
whether they can bind these to proper regulators instead.
We also amend the DT binding document. A small change like this
does not warrant a separate patch for augmenting these.
Cc: devicetree@vger.kernel.org
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver stashes a CODEC pointer in the cs35l35_private structure,
which is used to obtain a struct device pointer for error messages in the
interrupt handler.
However, doing so is not very safe as the interrupt is registered, as it
should be in bus probe, but the CODEC pointer can't be safely stored until
the ASoC level probe. This leaves a window between the two probes where if
any interrupts are received a NULL pointer will be deferenced in the IRQ
handler.
Fix this issue by saving a pointer to the device directly and passing that
to the error messages in the interrupt handler rather than using the CODEC
pointer to access the device pointer.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I2S2 and I2S3 are share pins. We need to configure it when i2s is
active and disable it when i2s is inactive. To disable i2s pins
means to set them as gpio.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds the ADI AU1761 audio codec as a selectable option
in the kernel config. Currently the driver can only be selected
for ADI blackfin devices or if SND_SOC_ALL_CODECS is enabled.
Signed-off-by: Bryce Ferguson <bryce.ferguson@rockwellcollins.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move set_sysclk to codec level and people can use it at both
codec and dai level.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move set_pll function to codec level and people can use it at both
codec and dai level. Also, lower case "source" to keep it consistent.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If cs35l35->pdata.stereo is false then "ret" isn't initialized.
Fixes: 6387f866a2 ("ASoC: Add support for Cirrus Logic CS35L35 Amplifier")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove extraneous tab to correct the nesting level indentation
Detected by CoverityScan, CID#1416584 ("Nesting level does
not match indentation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Oder Chiou