We need to compute the frame virtual address at different points.
Do it once.
Following patch will use the new va address for validate_loopback()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of fetching dma address from rx_desc->data[0].addr,
prefer using frags[0].dma + frags[0].page_offset to avoid
a potential cache line miss.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new counter tracks number of pages that we allocated for one port.
lpaa24:~# ethtool -S eth0 | egrep 'rx_alloc_pages|rx_packets'
rx_packets: 306755183
rx_alloc_pages: 932897
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same technique than some Intel drivers, for arches where PAGE_SIZE = 4096
In most cases, pages are reused because they were consumed
before we could loop around the RX ring.
This brings back performance, and is even better,
a single TCP flow reaches 30Gbit on my hosts.
v2: added full memset() in mlx4_en_free_frag(), as Tariq found it was needed
if we switch to large MTU, as priv->log_rx_info can dynamically be changed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of order-3 pages is problematic in some cases.
This patch might add three kinds of regression :
1) a CPU performance regression, but we will add later page
recycling and performance should be back.
2) TCP receiver could grow its receive window slightly slower,
because skb->len/skb->truesize ratio will decrease.
This is mostly ok, we prefer being conservative to not risk OOM,
and eventually tune TCP better in the future.
This is consistent with other drivers using 2048 per ethernet frame.
3) Because we allocate one page per RX slot, we consume more
memory for the ring buffers. XDP already had this constraint anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon use order-0 pages, and frag truesize will more precisely
match real sizes.
In the new model, we prefer to use <= 2048 bytes fragments, so that
we can use page-recycle technique on PAGE_SIZE=4096 arches.
We will still pack as much frames as possible on arches with big
pages, like PowerPC.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need to store the page and dma address.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to duplicate it per RX queue / frags.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using per frag storage for frag_prefix_size is really silly.
mlx4_en_complete_rx_desc() has all needed info already.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is really a port attribute, no need to duplicate it per
RX queue and per frag.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to duplicate it for all queues and frags.
num_frags & log_rx_info become u8 to save space.
u8 accesses are a bit faster than u16 anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: cosmetics
Couple of cosmetic mlxsw patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The overrun ignore bit isn't supported by the device's firmware and was
recently removed from the programmer's reference manual (PRM).
Remove it from the driver as well.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dd82364c3a ("mlxsw: Flip to the new dev walk API") did some
small changes in mlxsw code, but it did not respect the naming
conventions. So fix this now.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__sk_dst_set() must be called while we own the socket.
We can get proper lockdep coverage using lockdep_sock_is_held()
and rcu_dereference_protected()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
flow dissector improvements
This patchset follows-up the discussion about future extensions of flow
dissector and tries to address the mentioned concerns. Some parts are
cut out into sub-functions. Also, the processing of the code (ARP, MPLS)
is made dependent on user actually requiring the bisected values.
This prepares the code for future extensions to bisect IPv6 ND messages,
TCP flags, etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the main flow_dissect function a bit smaller and move the GRE
dissection into a separate function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align with "ip_proto_again" label used in the same function and rename
vague "again" to "proto_again".
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now, when an unexpected element in the GRE header appears, we break so
the l4 ports are processed. But since the ports are processed
unconditionally, there will be certainly random values dissected. Fix
this by just bailing out in such situations.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the main flow_dissect function a bit smaller and move the MPLS
dissection into a separate function. Along with that, do the MPLS header
processing only in case the flow dissection user requires it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the main flow_dissect function a bit smaller and move the ARP
dissection into a separate function. Along with that, do the ARP header
processing only in case the flow dissection user requires it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the setup_tc ndo to configure prioritised Tx traffic classes.
Priorities range from 0 (lowest) to 3 (highest). The driver assigns
NR_CPUS queues to each traffic class.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Each traffic class corresponds to a WQ priority level. The number of Tx
netdev queues and frame queues is increased to NR_CPUS queues for each
traffic class. In addition, the priority of the Rx, Error and Conf queues
is lowered but their order is maintained.
By default, only one traffic class is enabled, only the low priority Tx
queues are used and only the corresponding netdev queues are advertised.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use existing TCP nagle macro TCP_NAGLE_OFF and TCP_NAGLE_CORK instead
of the literal number 1 and 2 in the current decnet codes.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust the impedance values of the RX and TX lanes in the SGMII block
so that they are closer to optimal values.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Mason says:
====================
net: ethernet: bgmac: PM support and clean-ups
Changes in v3:
* Corrected a bug Florian found and added his Reviewed-by
Changes in v2:
* Reworked the PM patch with Florian's suggestions
Add code to support Power Management (only tested on NS2), and add some
code clean-ups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement suspend/resume callbacks in the bgmac driver. This makes sure
that we de-initialize and re-initialize the hardware correctly before
entering suspend and when resuming.
Signed-off-by: Joey Zhong <zhongx@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM471X and BCM535X are of the same family (from what I can derive from
internal documents). Group them into the case statement together, which
results in more code reuse.
Also, use existing helper variables to make the code a little more
readable too.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum frame size is really just the standard ethernet frame size
and FCS. So use those existing defines to make the code a little more
beautiful.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() to set a random MAC address in order to make
sure ndev->addr_assign_type will be properly set to NET_ADDR_RANDOM.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger says:
====================
NAPI support for Hyper-V
These patches enable NAPI, GRO and napi_alloc_skb for Hyper-V netvsc
driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use NAPI (softirq), to handle receive packets and send completions.
Previously this was handled by tasklet.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet