This fixes errors like bellow when LE Connection times out since that
is actually not a controller error:
Bluetooth: hci0: Opcode 0x200d failed: -110
Bluetooth: hci0: request failed to create LE connection: err -110
Instead the code shall properly detect if -ETIMEDOUT is returned and
send HCI_OP_LE_CREATE_CONN_CANCEL to give up on the connection.
Link: https://github.com/bluez/bluez/issues/340
Fixes: 8e8b92ee60 ("Bluetooth: hci_sync: Add hci_le_create_conn_sync")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Current flow interates over entire ACPI table entries looking for
Bluetooth Per Platform Antenna Gain(PPAG) entry. This patch iterates
over ACPI entries relvant to Bluetooth device only.
Fixes: c585a92b2f ("Bluetooth: btintel: Set Per Platform Antenna Gain(PPAG)")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Userspace needs to know whether the adapter has feature support for
Connected Isochronous Stream - Central/Peripheral, so it can set up
LE Audio features accordingly.
Expose these feature bits as settings in MGMT controller info.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Broadcom 4377 controllers found in Apple x86 Macs with the T2 chip
claim to support extended scanning when querying supported states,
< HCI Command: LE Read Supported St.. (0x08|0x001c) plen 0
> HCI Event: Command Complete (0x0e) plen 12
LE Read Supported States (0x08|0x001c) ncmd 1
Status: Success (0x00)
States: 0x000003ffffffffff
[...]
LE Set Extended Scan Parameters (Octet 37 - Bit 5)
LE Set Extended Scan Enable (Octet 37 - Bit 6)
[...]
, but then fail to actually implement the extended scanning:
< HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8
Own address type: Random (0x01)
Filter policy: Accept all advertisement (0x00)
PHYs: 0x01
Entry 0: LE 1M
Type: Active (0x01)
Interval: 11.250 msec (0x0012)
Window: 11.250 msec (0x0012)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
Status: Unknown HCI Command (0x01)
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Broadcom controllers present on Apple Silicon devices use the upper
8 bits of the event type in the LE Extended Advertising Report for
the channel on which the frame has been received.
These bits are reserved according to the Bluetooth spec anyway such that
we can just drop them to ensure that the advertising results are parsed
correctly.
The following excerpt from a btmon trace shows a report received on
channel 37 by these controllers:
> HCI Event: LE Meta Event (0x3e) plen 55
LE Extended Advertising Report (0x0d)
Num reports: 1
Entry 0
Event type: 0x2513
Props: 0x0013
Connectable
Scannable
Use legacy advertising PDUs
Data status: Complete
Reserved (0x2500)
Legacy PDU Type: Reserved (0x2513)
Address type: Public (0x00)
Address: XX:XX:XX:XX:XX:XX (Shenzhen Jingxun Software [...])
Primary PHY: LE 1M
Secondary PHY: No packets
SID: no ADI field (0xff)
TX power: 127 dBm
RSSI: -76 dBm (0xb4)
Periodic advertising interval: 0.00 msec (0x0000)
Direct address type: Public (0x00)
Direct address: 00:00:00:00:00:00 (OUI 00-00-00)
Data length: 0x1d
[...]
Flags: 0x18
Simultaneous LE and BR/EDR (Controller)
Simultaneous LE and BR/EDR (Host)
Company: Harman International Industries, Inc. (87)
Data: [...]
Service Data (UUID 0xfddf):
Name (complete): JBL Flip 5
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On cmd_timeout with no reset_gpio, reset the USB port as a last
resort.
This patch changes the behavior of btusb_intel_cmd_timeout and
btusb_rtl_cmd_timeout.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@google.com>
Reviewed-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
As per the specfication vendor codec id is defined.
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 4, Part E page 2127
Fixes: 9ae664028a ("Bluetooth: Add support for Read Local Supported Codecs V2")
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A patch series by a Qualcomm engineer essentially removed my
quirk/workaround because they thought it was unnecessary.
It wasn't, and it broke everything again:
https://patchwork.kernel.org/project/netdevbpf/list/?series=661703&archive=both&state=*
He argues that the quirk is not necessary because the code should check
if the dongle says if it's supported or not. The problem is that for
these Chinese CSR clones they say that it would work:
= New Index: 00:00:00:00:00:00 (Primary,USB,hci0)
= Open Index: 00:00:00:00:00:00
< HCI Command: Read Local Version Information (0x04|0x0001) plen 0
> HCI Event: Command Complete (0x0e) plen 12
> [hci0] 11.276039
Read Local Version Information (0x04|0x0001) ncmd 1
Status: Success (0x00)
HCI version: Bluetooth 5.0 (0x09) - Revision 2064 (0x0810)
LMP version: Bluetooth 5.0 (0x09) - Subversion 8978 (0x2312)
Manufacturer: Cambridge Silicon Radio (10)
...
< HCI Command: Read Local Supported Features (0x04|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 68
> [hci0] 11.668030
Read Local Supported Commands (0x04|0x0002) ncmd 1
Status: Success (0x00)
Commands: 163 entries
...
Read Default Erroneous Data Reporting (Octet 18 - Bit 2)
Write Default Erroneous Data Reporting (Octet 18 - Bit 3)
...
...
< HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0
= Close Index: 00:1A:7D:DA:71:XX
So bring it back wholesale.
Fixes: 63b1a7dd38 ("Bluetooth: hci_sync: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING")
Fixes: e168f69008 ("Bluetooth: btusb: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for fake CSR")
Fixes: 766ae2422b ("Bluetooth: hci_sync: Check LMP feature bit instead of quirk")
Cc: stable@vger.kernel.org
Cc: Zijun Hu <quic_zijuhu@quicinc.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Recent changes breaks HCIGETDEVINFO since it changes the size of
hci_dev_info.
Fixes: 26afbd826e ("Bluetooth: Add initial implementation of CIS connections")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This introduces a "Mesh UUID" and an Experimental Feature bit to the
hdev mask, and depending all underlying Mesh functionality on it.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The patch adds state bits, storage and HCI command chains for sending
and receiving Bluetooth Mesh advertising packets, and delivery to
requesting user space processes. It specifically creates 4 new MGMT
commands and 2 new MGMT events:
MGMT_OP_SET_MESH_RECEIVER - Sets passive scan parameters and a list of
AD Types which will trigger Mesh Packet Received events
MGMT_OP_MESH_READ_FEATURES - Returns information on how many outbound
Mesh packets can be simultaneously queued, and what the currently queued
handles are.
MGMT_OP_MESH_SEND - Command to queue a specific outbound Mesh packet,
with the number of times it should be sent, and the BD Addr to use.
Discrete advertisments are added to the ADV Instance list.
MGMT_OP_MESH_SEND_CANCEL - Command to cancel a prior outbound message
request.
MGMT_EV_MESH_DEVICE_FOUND - Event to deliver entire received Mesh
Advertisement packet, along with timing information.
MGMT_EV_MESH_PACKET_CMPLT - Event to indicate that an outbound packet is
no longer queued for delivery.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_abort_conn() is a wrapper around a number of DISCONNECT and
CREATE_CONN_CANCEL commands that was being invoked from hci_request
request queues, which are now deprecated. There are two versions:
hci_abort_conn() which can be invoked from the hci_event thread, and
hci_abort_conn_sync() which can be invoked within a hci_sync cmd chain.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_update_adv_data() is called from hci_event and hci_core due to
events from the controller. The prior function used the deprecated
hci_request method, and the new one uses hci_sync.c
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This function has no dependencies on the deprecated hci_request
mechanism, so has been moved unchanged to hci_sync.c
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The Advertising Instance expiration timer adv_instance_expire was
handled with the deprecated hci_request mechanism, rather than it's
replacement: hci_sync.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the following trace which is caused by hci_rx_work starting up
*after* the final channel reference has been put() during sock_close() but
*before* the references to the channel have been destroyed, so instead
the code now rely on kref_get_unless_zero/l2cap_chan_hold_unless_zero to
prevent referencing a channel that is about to be destroyed.
refcount_t: increment on 0; use-after-free.
BUG: KASAN: use-after-free in refcount_dec_and_test+0x20/0xd0
Read of size 4 at addr ffffffc114f5bf18 by task kworker/u17:14/705
CPU: 4 PID: 705 Comm: kworker/u17:14 Tainted: G S W
4.14.234-00003-g1fb6d0bd49a4-dirty #28
Hardware name: Qualcomm Technologies, Inc. SM8150 V2 PM8150
Google Inc. MSM sm8150 Flame DVT (DT)
Workqueue: hci0 hci_rx_work
Call trace:
dump_backtrace+0x0/0x378
show_stack+0x20/0x2c
dump_stack+0x124/0x148
print_address_description+0x80/0x2e8
__kasan_report+0x168/0x188
kasan_report+0x10/0x18
__asan_load4+0x84/0x8c
refcount_dec_and_test+0x20/0xd0
l2cap_chan_put+0x48/0x12c
l2cap_recv_frame+0x4770/0x6550
l2cap_recv_acldata+0x44c/0x7a4
hci_acldata_packet+0x100/0x188
hci_rx_work+0x178/0x23c
process_one_work+0x35c/0x95c
worker_thread+0x4cc/0x960
kthread+0x1a8/0x1c4
ret_from_fork+0x10/0x18
Cc: stable@kernel.org
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds broadcast support for BTPROTO_ISO by extending the
sockaddr_iso with a new struct sockaddr_iso_bc where the socket user
can set the broadcast address when receiving, the SID and the BIS
indexes it wants to synchronize.
When using BTPROTO_ISO for broadcast the roles are:
Broadcaster -> uses connect with address set to BDADDR_ANY:
> tools/isotest -s 00:00:00:00:00:00
Broadcast Receiver -> uses listen with address set to broadcaster:
> tools/isotest -d 00:AA:01:00:00:00
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This introduces a new socket type BTPROTO_ISO which can be enabled with
use of ISO Socket experiemental UUID, it can used to initiate/accept
connections and transfer packets between userspace and kernel similarly
to how BTPROTO_SCO works:
Central -> uses connect with address set to destination bdaddr:
> tools/isotest -s 00:AA:01:00:00:00
Peripheral -> uses listen:
> tools/isotest -d
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This introduces hci_recv_event_data to make it simpler to access the
contents of last received event rather than having to pass its contents
to the likes of *_ind/*_cfm callbacks.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This removes the remaining calls to HCI_OP_WRITE_SCAN_ENABLE from
hci_request call chains, and converts them to hci_sync calls.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The discov_update work queue is no longer used as a result
of the hci_sync rework.
The __hci_req_hci_power_on() function is no longer referenced in the
code as a result of the hci_sync rework.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Make use of hci_cmd_sync_queue for removing an advertisement monitor.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Miao-chen Chou <mcchou@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Make use of hci_cmd_sync_queue for adding an advertisement monitor.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Miao-chen Chou <mcchou@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Core driver addtionally checks LMP feature bit "Erroneous Data Reporting"
instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so
remove this unnecessary quirk.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BT core driver should addtionally check LMP feature bit
"Erroneous Data Reporting" instead of quirk
HCI_QUIRK_BROKEN_ERR_DATA_REPORTING set by BT device driver to decide if
HCI commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken.
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 2, Part C | page 587
This feature indicates whether the device is able to support the
Packet_Status_Flag and the HCI commands HCI_Write_Default_-
Erroneous_Data_Reporting and HCI_Read_Default_Erroneous_-
Data_Reporting.
the quirk was introduced by 'commit cde1a8a992 ("Bluetooth: btusb: Fix
and detect most of the Chinese Bluetooth controllers")' to mark HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting broken by BT
device driver, but the reason why these two HCI commands are broken is
that feature "Erroneous Data Reporting" is not enabled by firmware, this
scenario is illustrated by below log of QCA controllers with USB I/F:
@ RAW Open: hcitool (privileged) version 2.22
< HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0
> HCI Event: Command Complete (0x0e) plen 68
Read Local Supported Commands (0x04|0x0002) ncmd 1
Status: Success (0x00)
Commands: 288 entries
......
Read Default Erroneous Data Reporting (Octet 18 - Bit 2)
Write Default Erroneous Data Reporting (Octet 18 - Bit 3)
......
< HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0
> HCI Event: Command Complete (0x0e) plen 4
Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1
Status: Unknown HCI Command (0x01)
< HCI Command: Read Local Supported Features (0x04|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 12
Read Local Supported Features (0x04|0x0003) ncmd 1
Status: Success (0x00)
Features: 0xff 0xfe 0x0f 0xfe 0xd8 0x3f 0x5b 0x87
3 slot packets
......
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The bt_skb_sendmsg() function can't return NULL so there is no need to
check for that. Several of these checks were removed previously but
this one was missed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The scan response and advertising data needs to be tracked on a per
instance (adv_info) since when these instaces are removed so are their
data, to fix that new flags are introduced which is used to mark when
the data changes and then checked to confirm when the data needs to be
synced with the controller.
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When HCI_USERCHANNEL is used, unregister the suspend notifier when
binding and register when releasing. The userchannel socket should be
left alone after open is completed.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The bluetooth code uses our bitmap infrastructure for the two bits (!)
of connection setup flags, and in the process causes odd problems when
it converts between a bitmap and just the regular values of said bits.
It's completely pointless to do things like bitmap_to_arr32() to convert
a bitmap into a u32. It shoudln't have been a bitmap in the first
place. The reason to use bitmaps is if you have arbitrary number of
bits you want to manage (not two!), or if you rely on the atomicity
guarantees of the bitmap setting and clearing.
The code could use an "atomic_t" and use "atomic_or/andnot()" to set and
clear the bit values, but considering that it then copies the bitmaps
around with "bitmap_to_arr32()" and friends, there clearly cannot be a
lot of atomicity requirements.
So just use a regular integer.
In the process, this avoids the warnings about erroneous use of
bitmap_from_u64() which were triggered on 32-bit architectures when
conversion from a u64 would access two words (and, surprise, surprise,
only one word is needed - and indeed overkill - for a 2-bit bitmap).
That was always problematic, but the compiler seems to notice it and
warn about the invalid pattern only after commit 0a97953fd2 ("lib: add
bitmap_{from,to}_arr64") changed the exact implementation details of
'bitmap_from_u64()', as reported by Sudip Mukherjee and Stephen Rothwell.
Fixes: fe92ee6425 ("Bluetooth: hci_core: Rework hci_conn_params flags")
Link: https://lore.kernel.org/all/YpyJ9qTNHJzz0FHY@debian/
Link: https://lore.kernel.org/all/20220606080631.0c3014f2@canb.auug.org.au/
Link: https://lore.kernel.org/all/20220605162537.1604762-1-yury.norov@gmail.com/
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds helpers for accessing and appending service data (0x16) ad
type.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN quirk which can be
used to mark HCI_Enhanced_Setup_Synchronous_Connection as broken even
if its support command bit are set since some controller report it as
supported but the command don't work properly with some configurations
(e.g. BT_VOICE_TRANSPARENT/mSBC).
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Set a size limit of 8 bytes of the written buffer to "hdev->name"
including the terminating null byte, as the size of "hdev->name" is 8
bytes. If an id value which is greater than 9999 is allocated,
then the "snprintf(hdev->name, sizeof(hdev->name), "hci%d", id)"
function call would lead to a truncation of the id value in decimal
notation.
Set an explicit maximum id parameter in the id allocation function call.
The id allocation function defines the maximum allocated id value as the
maximum id parameter value minus one. Therefore, HCI_MAX_ID is defined
as 10000.
Signed-off-by: Itay Iellin <ieitayie@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This attempts to cleanup the hci_conn if it cannot be aborted as
otherwise it would likely result in having the controller and host
stack out of sync with respect to connection handle.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit d5ebaa7c5f introduces checks for handle range
(e.g HCI_CONN_HANDLE_MAX) but controllers like Intel AX200 don't seem
to respect the valid range int case of error status:
> HCI Event: Connect Complete (0x03) plen 11
Status: Page Timeout (0x04)
Handle: 65535
Address: 94:DB:56:XX:XX:XX (Sony Home Entertainment&
Sound Products Inc)
Link type: ACL (0x01)
Encryption: Disabled (0x00)
[1644965.827560] Bluetooth: hci0: Ignoring HCI_Connection_Complete for invalid handle
Because of it is impossible to cleanup the connections properly since
the stack would attempt to cancel the connection which is no longer in
progress causing the following trace:
< HCI Command: Create Connection Cancel (0x01|0x0008) plen 6
Address: 94:DB:56:XX:XX:XX (Sony Home Entertainment&
Sound Products Inc)
= bluetoothd: src/profile.c:record_cb() Unable to get Hands-Free Voice
gateway SDP record: Connection timed out
> HCI Event: Command Complete (0x0e) plen 10
Create Connection Cancel (0x01|0x0008) ncmd 1
Status: Unknown Connection Identifier (0x02)
Address: 94:DB:56:XX:XX:XX (Sony Home Entertainment&
Sound Products Inc)
< HCI Command: Create Connection Cancel (0x01|0x0008) plen 6
Address: 94:DB:56:XX:XX:XX (Sony Home Entertainment&
Sound Products Inc)
Fixes: d5ebaa7c5f ("Bluetooth: hci_event: Ignore multiple conn complete events")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Core
----
- Introduce XDP multi-buffer support, allowing the use of XDP with
jumbo frame MTUs and combination with Rx coalescing offloads (LRO).
- Speed up netns dismantling (5x) and lower the memory cost a little.
Remove unnecessary per-netns sockets. Scope some lists to a netns.
Cut down RCU syncing. Use batch methods. Allow netdev registration
to complete out of order.
- Support distinguishing timestamp types (ingress vs egress) and
maintaining them across packet scrubbing points (e.g. redirect).
- Continue the work of annotating packet drop reasons throughout
the stack.
- Switch netdev error counters from an atomic to dynamically
allocated per-CPU counters.
- Rework a few preempt_disable(), local_irq_save() and busy waiting
sections problematic on PREEMPT_RT.
- Extend the ref_tracker to allow catching use-after-free bugs.
BPF
---
- Introduce "packing allocator" for BPF JIT images. JITed code is
marked read only, and used to be allocated at page granularity.
Custom allocator allows for more efficient memory use, lower
iTLB pressure and prevents identity mapping huge pages from
getting split.
- Make use of BTF type annotations (e.g. __user, __percpu) to enforce
the correct probe read access method, add appropriate helpers.
- Convert the BPF preload to use light skeleton and drop
the user-mode-driver dependency.
- Allow XDP BPF_PROG_RUN test infra to send real packets, enabling
its use as a packet generator.
- Allow local storage memory to be allocated with GFP_KERNEL if called
from a hook allowed to sleep.
- Introduce fprobe (multi kprobe) to speed up mass attachment (arch
bits to come later).
- Add unstable conntrack lookup helpers for BPF by using the BPF
kfunc infra.
- Allow cgroup BPF progs to return custom errors to user space.
- Add support for AF_UNIX iterator batching.
- Allow iterator programs to use sleepable helpers.
- Support JIT of add, and, or, xor and xchg atomic ops on arm64.
- Add BTFGen support to bpftool which allows to use CO-RE in kernels
without BTF info.
- Large number of libbpf API improvements, cleanups and deprecations.
Protocols
---------
- Micro-optimize UDPv6 Tx, gaining up to 5% in test on dummy netdev.
- Adjust TSO packet sizes based on min_rtt, allowing very low latency
links (data centers) to always send full-sized TSO super-frames.
- Make IPv6 flow label changes (AKA hash rethink) more configurable,
via sysctl and setsockopt. Distinguish between server and client
behavior.
- VxLAN support to "collect metadata" devices to terminate only
configured VNIs. This is similar to VLAN filtering in the bridge.
- Support inserting IPv6 IOAM information to a fraction of frames.
- Add protocol attribute to IP addresses to allow identifying where
given address comes from (kernel-generated, DHCP etc.)
- Support setting socket and IPv6 options via cmsg on ping6 sockets.
- Reject mis-use of ECN bits in IP headers as part of DSCP/TOS.
Define dscp_t and stop taking ECN bits into account in fib-rules.
- Add support for locked bridge ports (for 802.1X).
- tun: support NAPI for packets received from batched XDP buffs,
doubling the performance in some scenarios.
- IPv6 extension header handling in Open vSwitch.
- Support IPv6 control message load balancing in bonding, prevent
neighbor solicitation and advertisement from using the wrong port.
Support NS/NA monitor selection similar to existing ARP monitor.
- SMC
- improve performance with TCP_CORK and sendfile()
- support auto-corking
- support TCP_NODELAY
- MCTP (Management Component Transport Protocol)
- add user space tag control interface
- I2C binding driver (as specified by DMTF DSP0237)
- Multi-BSSID beacon handling in AP mode for WiFi.
- Bluetooth:
- handle MSFT Monitor Device Event
- add MGMT Adv Monitor Device Found/Lost events
- Multi-Path TCP:
- add support for the SO_SNDTIMEO socket option
- lots of selftest cleanups and improvements
- Increase the max PDU size in CAN ISOTP to 64 kB.
Driver API
----------
- Add HW counters for SW netdevs, a mechanism for devices which
offload packet forwarding to report packet statistics back to
software interfaces such as tunnels.
- Select the default NIC queue count as a fraction of number of
physical CPU cores, instead of hard-coding to 8.
- Expose devlink instance locks to drivers. Allow device layer of
drivers to use that lock directly instead of creating their own
which always runs into ordering issues in devlink callbacks.
- Add header/data split indication to guide user space enabling
of TCP zero-copy Rx.
- Allow configuring completion queue event size.
- Refactor page_pool to enable fragmenting after allocation.
- Add allocation and page reuse statistics to page_pool.
- Improve Multiple Spanning Trees support in the bridge to allow
reuse of topologies across VLANs, saving HW resources in switches.
- DSA (Distributed Switch Architecture):
- replay and offload of host VLAN entries
- offload of static and local FDB entries on LAG interfaces
- FDB isolation and unicast filtering
New hardware / drivers
----------------------
- Ethernet:
- LAN937x T1 PHYs
- Davicom DM9051 SPI NIC driver
- Realtek RTL8367S, RTL8367RB-VB switch and MDIO
- Microchip ksz8563 switches
- Netronome NFP3800 SmartNICs
- Fungible SmartNICs
- MediaTek MT8195 switches
- WiFi:
- mt76: MediaTek mt7916
- mt76: MediaTek mt7921u USB adapters
- brcmfmac: Broadcom BCM43454/6
- Mobile:
- iosm: Intel M.2 7360 WWAN card
Drivers
-------
- Convert many drivers to the new phylink API built for split PCS
designs but also simplifying other cases.
- Intel Ethernet NICs:
- add TTY for GNSS module for E810T device
- improve AF_XDP performance
- GTP-C and GTP-U filter offload
- QinQ VLAN support
- Mellanox Ethernet NICs (mlx5):
- support xdp->data_meta
- multi-buffer XDP
- offload tc push_eth and pop_eth actions
- Netronome Ethernet NICs (nfp):
- flow-independent tc action hardware offload (police / meter)
- AF_XDP
- Other Ethernet NICs:
- at803x: fiber and SFP support
- xgmac: mdio: preamble suppression and custom MDC frequencies
- r8169: enable ASPM L1.2 if system vendor flags it as safe
- macb/gem: ZynqMP SGMII
- hns3: add TX push mode
- dpaa2-eth: software TSO
- lan743x: multi-queue, mdio, SGMII, PTP
- axienet: NAPI and GRO support
- Mellanox Ethernet switches (mlxsw):
- source and dest IP address rewrites
- RJ45 ports
- Marvell Ethernet switches (prestera):
- basic routing offload
- multi-chain TC ACL offload
- NXP embedded Ethernet switches (ocelot & felix):
- PTP over UDP with the ocelot-8021q DSA tagging protocol
- basic QoS classification on Felix DSA switch using dcbnl
- port mirroring for ocelot switches
- Microchip high-speed industrial Ethernet (sparx5):
- offloading of bridge port flooding flags
- PTP Hardware Clock
- Other embedded switches:
- lan966x: PTP Hardward Clock
- qca8k: mdio read/write operations via crafted Ethernet packets
- Qualcomm 802.11ax WiFi (ath11k):
- add LDPC FEC type and 802.11ax High Efficiency data in radiotap
- enable RX PPDU stats in monitor co-exist mode
- Intel WiFi (iwlwifi):
- UHB TAS enablement via BIOS
- band disablement via BIOS
- channel switch offload
- 32 Rx AMPDU sessions in newer devices
- MediaTek WiFi (mt76):
- background radar detection
- thermal management improvements on mt7915
- SAR support for more mt76 platforms
- MBSSID and 6 GHz band on mt7915
- RealTek WiFi:
- rtw89: AP mode
- rtw89: 160 MHz channels and 6 GHz band
- rtw89: hardware scan
- Bluetooth:
- mt7921s: wake on Bluetooth, SCO over I2S, wide-band-speed (WBS)
- Microchip CAN (mcp251xfd):
- multiple RX-FIFOs and runtime configurable RX/TX rings
- internal PLL, runtime PM handling simplification
- improve chip detection and error handling after wakeup
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ELpe
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"The sprinkling of SPI drivers is because we added a new one and Mark
sent us a SPI driver interface conversion pull request.
Core
----
- Introduce XDP multi-buffer support, allowing the use of XDP with
jumbo frame MTUs and combination with Rx coalescing offloads (LRO).
- Speed up netns dismantling (5x) and lower the memory cost a little.
Remove unnecessary per-netns sockets. Scope some lists to a netns.
Cut down RCU syncing. Use batch methods. Allow netdev registration
to complete out of order.
- Support distinguishing timestamp types (ingress vs egress) and
maintaining them across packet scrubbing points (e.g. redirect).
- Continue the work of annotating packet drop reasons throughout the
stack.
- Switch netdev error counters from an atomic to dynamically
allocated per-CPU counters.
- Rework a few preempt_disable(), local_irq_save() and busy waiting
sections problematic on PREEMPT_RT.
- Extend the ref_tracker to allow catching use-after-free bugs.
BPF
---
- Introduce "packing allocator" for BPF JIT images. JITed code is
marked read only, and used to be allocated at page granularity.
Custom allocator allows for more efficient memory use, lower iTLB
pressure and prevents identity mapping huge pages from getting
split.
- Make use of BTF type annotations (e.g. __user, __percpu) to enforce
the correct probe read access method, add appropriate helpers.
- Convert the BPF preload to use light skeleton and drop the
user-mode-driver dependency.
- Allow XDP BPF_PROG_RUN test infra to send real packets, enabling
its use as a packet generator.
- Allow local storage memory to be allocated with GFP_KERNEL if
called from a hook allowed to sleep.
- Introduce fprobe (multi kprobe) to speed up mass attachment (arch
bits to come later).
- Add unstable conntrack lookup helpers for BPF by using the BPF
kfunc infra.
- Allow cgroup BPF progs to return custom errors to user space.
- Add support for AF_UNIX iterator batching.
- Allow iterator programs to use sleepable helpers.
- Support JIT of add, and, or, xor and xchg atomic ops on arm64.
- Add BTFGen support to bpftool which allows to use CO-RE in kernels
without BTF info.
- Large number of libbpf API improvements, cleanups and deprecations.
Protocols
---------
- Micro-optimize UDPv6 Tx, gaining up to 5% in test on dummy netdev.
- Adjust TSO packet sizes based on min_rtt, allowing very low latency
links (data centers) to always send full-sized TSO super-frames.
- Make IPv6 flow label changes (AKA hash rethink) more configurable,
via sysctl and setsockopt. Distinguish between server and client
behavior.
- VxLAN support to "collect metadata" devices to terminate only
configured VNIs. This is similar to VLAN filtering in the bridge.
- Support inserting IPv6 IOAM information to a fraction of frames.
- Add protocol attribute to IP addresses to allow identifying where
given address comes from (kernel-generated, DHCP etc.)
- Support setting socket and IPv6 options via cmsg on ping6 sockets.
- Reject mis-use of ECN bits in IP headers as part of DSCP/TOS.
Define dscp_t and stop taking ECN bits into account in fib-rules.
- Add support for locked bridge ports (for 802.1X).
- tun: support NAPI for packets received from batched XDP buffs,
doubling the performance in some scenarios.
- IPv6 extension header handling in Open vSwitch.
- Support IPv6 control message load balancing in bonding, prevent
neighbor solicitation and advertisement from using the wrong port.
Support NS/NA monitor selection similar to existing ARP monitor.
- SMC
- improve performance with TCP_CORK and sendfile()
- support auto-corking
- support TCP_NODELAY
- MCTP (Management Component Transport Protocol)
- add user space tag control interface
- I2C binding driver (as specified by DMTF DSP0237)
- Multi-BSSID beacon handling in AP mode for WiFi.
- Bluetooth:
- handle MSFT Monitor Device Event
- add MGMT Adv Monitor Device Found/Lost events
- Multi-Path TCP:
- add support for the SO_SNDTIMEO socket option
- lots of selftest cleanups and improvements
- Increase the max PDU size in CAN ISOTP to 64 kB.
Driver API
----------
- Add HW counters for SW netdevs, a mechanism for devices which
offload packet forwarding to report packet statistics back to
software interfaces such as tunnels.
- Select the default NIC queue count as a fraction of number of
physical CPU cores, instead of hard-coding to 8.
- Expose devlink instance locks to drivers. Allow device layer of
drivers to use that lock directly instead of creating their own
which always runs into ordering issues in devlink callbacks.
- Add header/data split indication to guide user space enabling of
TCP zero-copy Rx.
- Allow configuring completion queue event size.
- Refactor page_pool to enable fragmenting after allocation.
- Add allocation and page reuse statistics to page_pool.
- Improve Multiple Spanning Trees support in the bridge to allow
reuse of topologies across VLANs, saving HW resources in switches.
- DSA (Distributed Switch Architecture):
- replay and offload of host VLAN entries
- offload of static and local FDB entries on LAG interfaces
- FDB isolation and unicast filtering
New hardware / drivers
----------------------
- Ethernet:
- LAN937x T1 PHYs
- Davicom DM9051 SPI NIC driver
- Realtek RTL8367S, RTL8367RB-VB switch and MDIO
- Microchip ksz8563 switches
- Netronome NFP3800 SmartNICs
- Fungible SmartNICs
- MediaTek MT8195 switches
- WiFi:
- mt76: MediaTek mt7916
- mt76: MediaTek mt7921u USB adapters
- brcmfmac: Broadcom BCM43454/6
- Mobile:
- iosm: Intel M.2 7360 WWAN card
Drivers
-------
- Convert many drivers to the new phylink API built for split PCS
designs but also simplifying other cases.
- Intel Ethernet NICs:
- add TTY for GNSS module for E810T device
- improve AF_XDP performance
- GTP-C and GTP-U filter offload
- QinQ VLAN support
- Mellanox Ethernet NICs (mlx5):
- support xdp->data_meta
- multi-buffer XDP
- offload tc push_eth and pop_eth actions
- Netronome Ethernet NICs (nfp):
- flow-independent tc action hardware offload (police / meter)
- AF_XDP
- Other Ethernet NICs:
- at803x: fiber and SFP support
- xgmac: mdio: preamble suppression and custom MDC frequencies
- r8169: enable ASPM L1.2 if system vendor flags it as safe
- macb/gem: ZynqMP SGMII
- hns3: add TX push mode
- dpaa2-eth: software TSO
- lan743x: multi-queue, mdio, SGMII, PTP
- axienet: NAPI and GRO support
- Mellanox Ethernet switches (mlxsw):
- source and dest IP address rewrites
- RJ45 ports
- Marvell Ethernet switches (prestera):
- basic routing offload
- multi-chain TC ACL offload
- NXP embedded Ethernet switches (ocelot & felix):
- PTP over UDP with the ocelot-8021q DSA tagging protocol
- basic QoS classification on Felix DSA switch using dcbnl
- port mirroring for ocelot switches
- Microchip high-speed industrial Ethernet (sparx5):
- offloading of bridge port flooding flags
- PTP Hardware Clock
- Other embedded switches:
- lan966x: PTP Hardward Clock
- qca8k: mdio read/write operations via crafted Ethernet packets
- Qualcomm 802.11ax WiFi (ath11k):
- add LDPC FEC type and 802.11ax High Efficiency data in radiotap
- enable RX PPDU stats in monitor co-exist mode
- Intel WiFi (iwlwifi):
- UHB TAS enablement via BIOS
- band disablement via BIOS
- channel switch offload
- 32 Rx AMPDU sessions in newer devices
- MediaTek WiFi (mt76):
- background radar detection
- thermal management improvements on mt7915
- SAR support for more mt76 platforms
- MBSSID and 6 GHz band on mt7915
- RealTek WiFi:
- rtw89: AP mode
- rtw89: 160 MHz channels and 6 GHz band
- rtw89: hardware scan
- Bluetooth:
- mt7921s: wake on Bluetooth, SCO over I2S, wide-band-speed (WBS)
- Microchip CAN (mcp251xfd):
- multiple RX-FIFOs and runtime configurable RX/TX rings
- internal PLL, runtime PM handling simplification
- improve chip detection and error handling after wakeup"
* tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2521 commits)
llc: fix netdevice reference leaks in llc_ui_bind()
drivers: ethernet: cpsw: fix panic when interrupt coaleceing is set via ethtool
ice: don't allow to run ice_send_event_to_aux() in atomic ctx
ice: fix 'scheduling while atomic' on aux critical err interrupt
net/sched: fix incorrect vlan_push_eth dest field
net: bridge: mst: Restrict info size queries to bridge ports
net: marvell: prestera: add missing destroy_workqueue() in prestera_module_init()
drivers: net: xgene: Fix regression in CRC stripping
net: geneve: add missing netlink policy and size for IFLA_GENEVE_INNER_PROTO_INHERIT
net: dsa: fix missing host-filtered multicast addresses
net/mlx5e: Fix build warning, detected write beyond size of field
iwlwifi: mvm: Don't fail if PPAG isn't supported
selftests/bpf: Fix kprobe_multi test.
Revert "rethook: x86: Add rethook x86 implementation"
Revert "arm64: rethook: Add arm64 rethook implementation"
Revert "powerpc: Add rethook support"
Revert "ARM: rethook: Add rethook arm implementation"
netdevice: add missing dm_private kdoc
net: bridge: mst: prevent NULL deref in br_mst_info_size()
selftests: forwarding: Use same VRF for port and VLAN upper
...
Hi Linus,
Please, pull the following treewide patch that replaces zero-length arrays with
flexible-array members. This patch has been baking in linux-next for a
whole development cycle.
Thanks
--
Gustavo
-----BEGIN PGP SIGNATURE-----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=xZD2
-----END PGP SIGNATURE-----
Merge tag 'flexible-array-transformations-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull flexible-array transformations from Gustavo Silva:
"Treewide patch that replaces zero-length arrays with flexible-array
members.
This has been baking in linux-next for a whole development cycle"
* tag 'flexible-array-transformations-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
treewide: Replace zero-length arrays with flexible-array members
Callers pass msg->msg_flags as flags, which contains MSG_DONTWAIT
instead of O_NONBLOCK.
Signed-off-by: Gavin Li <gavin@matician.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some controllers have problems with being sent a command to clear
all filtering. While the HCI code does not unconditionally
send a clear-all anymore at BR/EDR setup (after the state machine
refactor), there might be more ways of hitting these codepaths
in the future as the kernel develops.
Cc: stable@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes attemting to print hdev->name directly which causes them to
print an error:
kernel: read_version:367: (efault): sock 000000006a3008f2
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use "flexible array members" for these cases. The older
style of one-element or zero-length arrays should no longer be used.
Reference:
https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arrays
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When using hci_le_create_conn_sync it shall wait for the conn_timeout
since the connection complete may take longer than just 2 seconds.
Also fix the masking of HCI_EV_LE_ENHANCED_CONN_COMPLETE and
HCI_EV_LE_CONN_COMPLETE so they are never both set so we can predict
which one the controller will use in case of HCI_OP_LE_CREATE_CONN.
Fixes: 6cd29ec6ae ("Bluetooth: hci_sync: Wait for proper events when connecting LE")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz