Support for new chip revision. Revision read from the
internal register, PCIE config's "revision id" register
do not indicate HW version properly
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce enum to describe mapping type; allow 'none' in addition to
'single' and 'page'; this is preparation for GSO
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting fragmented skb for Tx, assign skb to the last descriptor
and set number of fragments in the 1-st one
On Tx complete, HW sets "DU" bit in Tx descriptor only for the last
descriptor; so search for it using number of fragments field.
Middle descriptors may have "DU" bit not set by the hardware.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New firmware do support scan while connected. Enable it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connection established, as reported by WMI_CONNECT_EVENTID,
4-way handshaking required for the secure connection is not done
yet. It is indicated by another WMI event. Wait for it and only then
allow data traffic. In case of non-secure connection, FW reports
"data port open" immediately after connection.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The registers for temperature compensation need to
be programmed only for active chains. Use the TX chainmask
to make sure that this is done properly for QCA953x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Along with AR9340 and AR955x, this is also needed for
the QCA953x SoC.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eeprom read operations are mixed in the probe function.
Make the code more readable and clean by extracting this code and
moving it in a dedicated function.
The variable eeprom_cck_table_adr, now useless, is here because
it will be needed for rtl8187se support, that I hope to add soon.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SLOT, SIFS, DIFS, EIFS, CW and ACK-timeout registers are set in an
RF-code callback and their values are fixed.
This patch moves this off the rf-code, and introduce two new functions
that calculate these values depending by slot time and CW values
requested by mac80211.
This seems to improve performances on my setup.
Currently the ack and slot time values could be stored in a local
variable, but this patch stores it in the driver "priv" structure
because it will be useful for rtl8187se support that will be added
(hopefully) soon.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Basic rates setting is done with hardcoded register write with
fixed settings.
This patch introduces a new function that makes it possible to
configure basic rates and it add a check for mac80211
BSS_CHANGED_BASIC_RATES flag in order to eventually invoke that
function when needed.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While changing board-type variable to enum, I have added enum
value for rtl8187se by mistake.
This will causes gcc warnings with unhandled switch/cases.
Remove it temporarily until I will push also rtl8187se changes.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nl80211 iftype was converted to a mode value and stored in
brcmf_cfg80211_vif structure. The value was used only within
brcmfmac driver to decide execution of conditional code. Better
use wireless_dev::iftype for that as the wdev is contained in
the brcmf_cfg80211_vif structure.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the SDIO driver goes in low power state it must assure that
a clock request in ChipCLKCSR is set. Otherwise waking up the
device can fail. The register is read and if necessary the ALP
clock will be requested.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connecting without specifying the channel it can take quite
some time to connect. This is because not all parameters for the
scan operation are set to optimized values. This patch changes
these parameters resulting in a much faster connect in certain
situations.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SDIO tx uses a sequence number which is common for data
and control. This requires that access to this sequence number
is protected. A mutex was used to achieve this, but it also
required the reordering of code for tx control.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BCM4354 is an a/b/g/n/ac 2x2 WiFi chip. This patch adds support for it through
SDIO interface.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we will need it to make common-beacon code work.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we will need it for ath9k_htc, may be other drivers too
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
to reduce difference between ath9k and ath9k_htc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable protocol offloading (arp and NS) on D0i3.
The offloading allows the fw answer NS and arp requests
without waking up the host.
Since protocol offloading is saved between D0i3
entries, we have to explicitly disable it in
case we don't want it.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In order to restore the qos seq number on d0i3 exit,
we need to read it from the wowlan status.
However, in order to make sure we use correct seq num
for tx frames, we need to defer any outgoing frames,
and re-enqueue them only after the seq num is configured
correctly.
Sync new Tx aggregations with D0i3 so that the correct
seq num is used for them. Wait synchronously for D0i3
exit before starting a new Tx agg.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Configure the QoS counters when entering D0i3.
The fw might use them later when performing protocol
offloading (we'll update the the counters back on
d0i3 exit in a following patch).
Non-QoS counter is handled internally in the fw, so
no need to configure it.
Also, add support for a new version of WOWLAN_CONFIG_CMD
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable beacon filter only if at least one beacon from candidate
AP is received before or after association. Check this condition before
enabling BF upon secured association completion. Add BF enablement to
mac80211 event that indicates beacon is received after association.
Too early beacon filtering enablement can lead to disconnection due to
missing AP's beacon after association.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Blink led mode is not supported by iwlmvm. This doesn't mean
that we should prevent any operation if it is selected by
the user.
Instead of failing without any notice to the user, fallback
to the default mode (RF mode) if the blink mode
is selected and print an error to inform the user.
Reported-by: Steven Haigh <netwiz@crc.id.au>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
instead of duplicating the same loop multiple times,
use a new function for it.
this will be later used also for clearing other
windows in the table.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Make _rs_collect_tx_data get window as param, in order
to be able to set various windows.
This will be used later for saving tpc statistics
as well.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently RTS protection was done whenever trasnmitting an AMPDU.
This limits throughput in cases where there's no need for protection.
Disable this too inclusive protection for now.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We should explore all possible columns when searching to be
as resilient as possible to changing conditions. This fixes
for example a scenario where even after a sudden creation of
rssi difference between the 2 antennas we would keep doing MIMO
at a low rate instead of switching to SISO at a higher rate using
the better antenna which was the optimal configuration.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Scheduled scan was disabled because it was broken. Now it is
fixed and got disabled by mistake by a merge.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the benefits of platform_driver_probe() is that you can make
the probe function __init.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On older chips, the INI value differ in similar ways as cycpwr_thr1, so
convert it to absolute values as well.
Since the ANI algorithm is different here compared to the old
implementation (fewer steps, controlled at a different point in time),
it makes sense to use values similar to what would be applied for newer
chips, just without relying on INI defaults.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The table was copied from the ANI implementation of AR9300. It assumes
that the INI values contain a baseline value that is usable as reference
from which to increase/decrease based on the noise immunity value.
On older chips, the differences are bigger and especially AR5008/AR9001
are configured to much more sensitive values than what is useful.
Improve ANI behavior by reverting to the absolute values used in the
previous implementation (expressed as a simple formula instead of the
old table).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The primary purpose of this piece of code was to selectively disable
OFDM weak signal detection. The checks for this are elsewhere, and an
earlier commit relaxed the restrictions for older chips, which are more
sensitive to interference.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 4c59ff221e "wireless: Kconfig: add missing dependency" added a number
of 'depends on CFG80211' statements, but missed the AIRO_CS driver that
also causes the airo.c file to be built. This adds the (hopefully) last
such missing statement
Cc: "Zhao, Gang" <gamerh2o@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcms_attach function is defined as static but the comment is
saying that it should not be static or gcc will issue a warning.
I believe we can remove the comment as I don't se a problem with
this function being defined as static.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When brcm80211 firmware is not installed networking hangs.
A deadlock happens because we call ieee80211_unregister_hw()
from the .start callback of struct ieee80211_ops. When .start
is called we are under rtnl lock and ieee80211_unregister_hw()
tries to take it again.
Function call stack:
dev_change_flags()
__dev_change_flags()
__dev_open()
ASSERT_RTNL() <-- Assert rtnl lock
ops->ndo_open()
.ndo_open = ieee80211_open,
ieee80211_open()
ieee80211_do_open()
drv_start()
local->ops->start()
.start = brcms_ops_start,
brcms_ops_start()
brcms_remove()
ieee80211_unregister_hw()
rtnl_lock() <-- Here we deadlock
Introduced by:
commit 25b5632fb3
("brcmsmac: request firmware in .start() callback")
This patch fixes the bug by removing the call to brcms_remove()
and moves the brcms_request_fw() call to the top of the .start
callback to not initiate anything unless firmware is installed.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unify scnprintf calls and include the current OFDM/CCK immunity level.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
qi->tqi_readyTime is written directly to registers that expect
microseconds as unit instead of TU.
When setting the CABQ ready time, cur_conf->beacon_interval is in TU, so
convert it to microseconds before passing it to ath9k_hw.
This should hopefully fix some Tx DMA issues with buffered multicast
frames in AP mode.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently a "r8185" integer variable is used as a boolean flag to
indicate whether the card is a rtl8185 or not.
Since now the driver supports only rtl8185 and rtl8180 cards, if
"r8185" variable is zero then the card is implicitly assumed to
be a rtl8180.
Now I'm preparing to add support for a third card type (rtl8187se).
This patch changes the "r8185" flag with an enum variable to
explicitly indicate which card type we have.
I'm submitting this this patch now, even if I still have to submit
other patches that not pertain with rtl8187se support, because
IMHO it's not worth rebasing them on the current code, using r8185
flag, and then changing them back again nearly immediately.
BTW if someone feels I really should do this, please tell me..
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently AMPDU aggregation is preferred over AMSDU. AMSDU
aggregation is performed only if AMPDU streams in firmware
are full.
This patch adds simultaneous AMSDU and AMPDU aggregation
support. This mechanism helps to improve throughput.
AMSDU is enabled only for 8897 chipsets which supports 4K
transmit buffer. User can disable AMSDU using
'disable_tx_amsdu' module parameter.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Existing mwifiex_11n_dispatch_pkt() function is renamed as
mwifiex_11n_dispatch_pkt_until_start_win() and a new function
mwifiex_11n_dispatch_pkt() is created for a common code which
dispatches single packet based on interface type.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use negative check for 'status' and return from the function.
This improves readability by avoiding line splits. Also, local
variable is used for start window calculations.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As V15 firmware supports VHT rate configuration, we can use this
information received in set bitrate mask handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware API version number will be used for future patches
to support different firmware API specs.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If p54u_load_firmware() fails, p54u_probe() does not deallocate
already allocated resources. The patch adds proper failure handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit eac40d9631. It cause
random connection drops on RT5390 PCI adapters.
On Mediatek there is different driver version available for RT53xx chip
based on bus type (2.5.0.3 for PCI and 2.6.1.3 for USB). Hence possibly
we should set registers differently based on bus type. But is also
possible that new driver (i.e. 2.6.1.3) was not verified on RT53xx USB.
Until we figure out how to initialize registers properly for RT53xx just
revert commit eac40d9631 since it cause
regression.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit 558ff225de (ath9k: fix
ps-poll responses under a-mpdu sessions) non-data frames would have
gotten a sequence number from a TIDs sequence counter instead of
using the global sequence counter.
This can lead to instable connections.
To fix this only select the correct TID if we are processing a
data frame. Furthermore, prevent non-data frames to get a sequence
number from a TID sequence counter by adding a check to
ath_tx_setup_buffer.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: reduce baseband hang detection false positive rate"
added a delay in the loop checking the baseband state, however it was
unreachable due to previous 'continue' statements.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 1eb4301867 (brcmfmac: fix txglomming scatter-gather packet transfers)
added an allocation of an skb via brcmu_pkt_buf_get_skb() but forgot to
free it on one of the error paths.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Dave Jones<davej@fedoraproject.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit a619d1abe2 leads to the following static checker warning:
drivers/net/wireless/rtlwifi/rtl8723be/phy.c:667 _rtl8723be_store_tx_power_by_rate()
error: buffer overflow 'rtlphy->tx_power_by_rate_offset[band]' 4 <= 5
This warning arises because the code is testing the indices for the wrong maximum
values. In addition, the tests merely putput a warning, and then procedes to
corrupt memory. With this change, any such invalid memory access is avoided.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The help text were either out of date, too small or didn't exist at all. Also
move cfg80211 dependency to ath6kl_core module as it has all the calls to
cfg80211.
Fixes checkpatch warning:
WARNING: please write a paragraph that describes the config symbol fully
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
CHECK: Blank lines aren't necessary after an open brace '{'
CHECK: Blank lines aren't necessary before a close brace '}'
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Jason noticed that with Yocto GCC 4.8.1 ath6kl crashes with this iperf command:
iperf -c $TARGET_IP -i 5 -t 50 -w 1M
The crash was:
Unable to handle kernel paging request at virtual address 1a480000
pgd = 80004000
[1a480000] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
Modules linked in: ath6kl_sdio ath6kl_core [last unloaded: ath6kl_core]
CPU: 0 PID: 1953 Comm: kworker/u4:0 Not tainted 3.10.9-1.0.0_alpha+dbf364b #1
Workqueue: ath6kl ath6kl_sdio_write_async_work [ath6kl_sdio]
task: dcc9a680 ti: dc9ae000 task.ti: dc9ae000
PC is at v7_dma_clean_range+0x20/0x38
LR is at dma_cache_maint_page+0x50/0x54
pc : [<8001a6f8>] lr : [<800170fc>] psr: 20000093
sp : dc9afcf8 ip : 8001a748 fp : 00000004
r10: 00000000 r9 : 00000001 r8 : 00000000
r7 : 00000001 r6 : 00000000 r5 : 80cb7000 r4 : 03f9a480
r3 : 0000001f r2 : 00000020 r1 : 1a480000 r0 : 1a480000
Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c53c7d Table: 6cc5004a DAC: 00000015
Process kworker/u4:0 (pid: 1953, stack limit = 0xdc9ae238)
Stack: (0xdc9afcf8 to 0xdc9b0000)
fce0: 80c9b29c 00000000
fd00: 00000000 80017134 8001a748 dc302ac0 00000000 00000000 dc454a00 80c12ed8
fd20: dc115410 80017238 00000000 dc454a10 00000001 80017588 00000001 00000000
fd40: 00000000 dc302ac0 dc9afe38 dc9afe68 00000004 80c12ed8 00000000 dc454a00
fd60: 00000004 80436f88 00000000 00000000 00000600 0000ffff 0000000c 80c113c4
fd80: 80c9b29c 00000001 00000004 dc115470 60000013 dc302ac0 dc46e000 dc302800
fda0: dc9afe10 dc302b78 60000013 dc302ac0 dc46e000 00000035 dc46e5b0 80438c90
fdc0: dc9afe10 dc302800 dc302800 dc9afe68 dc9afe38 80424cb4 00000005 dc9afe10
fde0: dc9afe20 80424de8 dc9afe10 dc302800 dc46e910 80424e90 dc473c00 dc454f00
fe00: 000001b5 7f619d64 dcc7c830 00000000 00000000 dc9afe38 dc9afe68 00000000
fe20: 00000000 00000000 dc9afe28 dc9afe28 80424d80 00000000 00000035 9cac0034
fe40: 00000000 00000000 00000000 00000000 000001b5 00000000 00000000 00000000
fe60: dc9afe68 dc9afe10 3b9aca00 00000000 00000080 00000034 00000000 00000100
fe80: 00000000 00000000 dc9afe10 00000004 dc454a00 00000000 dc46e010 dc46e96c
fea0: dc46e000 dc46e964 00200200 00100100 dc46e910 7f619ec0 00000600 80c0e770
fec0: dc15a900 dcc7c838 00000000 dc46e954 8042d434 dcc44680 dc46e954 dc004400
fee0: dc454500 00000000 00000000 dc9ae038 dc004400 8003c450 dcc44680 dc004414
ff00: dc46e954 dc454500 00000001 dcc44680 dc004414 dcc44698 dc9ae000 dc9ae030
ff20: 00000001 dc9ae000 dc004400 8003d158 8003d020 00000000 00000000 80c53941
ff40: dc9aff64 dcb71ea0 00000000 dcc44680 8003d020 00000000 00000000 00000000
ff60: 00000000 80042480 00000000 00000000 000000f8 dcc44680 00000000 00000000
ff80: dc9aff80 dc9aff80 00000000 00000000 dc9aff90 dc9aff90 dc9affac dcb71ea0
ffa0: 800423cc 00000000 00000000 8000e018 00000000 00000000 00000000 00000000
ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<8001a6f8>] (v7_dma_clean_range+0x20/0x38) from [<800170fc>] (dma_cache_maint_page+0x50/0x54)
[<800170fc>] (dma_cache_maint_page+0x50/0x54) from [<80017134>] (__dma_page_cpu_to_dev+0x34/0x9c)
[<80017134>] (__dma_page_cpu_to_dev+0x34/0x9c) from [<80017238>] (arm_dma_map_page+0x64/0x68)
[<80017238>] (arm_dma_map_page+0x64/0x68) from [<80017588>] (arm_dma_map_sg+0x7c/0xf4)
[<80017588>] (arm_dma_map_sg+0x7c/0xf4) from [<80436f88>] (sdhci_send_command+0x894/0xe00)
[<80436f88>] (sdhci_send_command+0x894/0xe00) from [<80438c90>] (sdhci_request+0xc0/0x1ec)
[<80438c90>] (sdhci_request+0xc0/0x1ec) from [<80424cb4>] (mmc_start_request+0xb8/0xd4)
[<80424cb4>] (mmc_start_request+0xb8/0xd4) from [<80424de8>] (__mmc_start_req+0x60/0x84)
[<80424de8>] (__mmc_start_req+0x60/0x84) from [<80424e90>] (mmc_wait_for_req+0x10/0x20)
[<80424e90>] (mmc_wait_for_req+0x10/0x20) from [<7f619d64>] (ath6kl_sdio_scat_rw.isra.10+0x1dc/0x240 [ath6kl_sdio])
[<7f619d64>] (ath6kl_sdio_scat_rw.isra.10+0x1dc/0x240 [ath6kl_sdio]) from [<7f619ec0>] (ath6kl_sdio_write_async_work+0x5c/0x104 [ath6kl_sdio])
[<7f619ec0>] (ath6kl_sdio_write_async_work+0x5c/0x104 [ath6kl_sdio]) from [<8003c450>] (process_one_work+0x10c/0x370)
[<8003c450>] (process_one_work+0x10c/0x370) from [<8003d158>] (worker_thread+0x138/0x3fc)
[<8003d158>] (worker_thread+0x138/0x3fc) from [<80042480>] (kthread+0xb4/0xb8)
[<80042480>] (kthread+0xb4/0xb8) from [<8000e018>] (ret_from_fork+0x14/0x3c)
Code: e1a02312 e2423001 e1c00003 f57ff04f (ee070f3a)
---[ end trace 0c038f0b8e0b67a3 ]---
Kernel panic - not syncing: Fatal exception
Jason's analysis:
"The GCC 4.8.1 compiler will not do the for-loop till scat_entries, instead,
it only run one round loop. This may be caused by that the GCC 4.8.1 thought
that the scat_list only have one item and then no need to do full iteration,
but this is simply wrong by looking at the assebly code. This will cause the sg
buffer not get set when scat_entries > 1 and thus lead to kernel panic.
Note: This issue not observed with GCC 4.7.2, only found on the GCC 4.8.1)"
Fix this by using the normal [0] style for defining unknown number of list
entries following the struct. This also fixes corruption with scat_q_depth, which
was mistankely added to the end of struct and overwritten if there were more
than item in the scat list.
Reported-by: Jason Liu <r64343@freescale.com>
Tested-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add recalculation of RTS/CTS protection when one or more legacy
stations are connected to ath10k. In this case enable RTS/CTS
protection and set sw retry profile are needed in the FW.
Without this change legacy station is starved and has very low
throughput.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We can now define the priority against BT per AC. This is
possible with a newer firmware that allows to define the
priority with 2 bits.
Note that this change is compatible with older firmware
since older firmware will simply ignore the new bit (11),
and we still set the old bit (12) in the same cases as
before.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This code is really related to BT Coex - move it to the coex
file.
Also - prepare for a FW API change that will happen soon:
Bits 11 and 12 will be allocated for BT priority. Today, we
only have bit 12.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
7265 features a new calibration which is called antenna
coupling. The purpose of this calibration (which isn't
really a calibration), is to measure the isolation between
the antennas and that can give us useful information for
the Coex modules.
With this information, we can tune the LookUpTables (LUTs)
that define the BT / WiFi contention policy.
The LUTs currently contain dummy values - but they will be
updated soon.
While at it, change the current code to stop duplicate the
host command while sending. This was needed back then, when
the command was short enough to be allocated on the stack.
Since then, the command grew a lot and is now allocated on
the heap - hence we can use the NOCOPY option instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is a flow in which we send the host command in SYNC
mode, but we don't take priv->mutex.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1046495
Cc: <stable@vger.kernel.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
IBSS mode requires the changing of supported rate. Do this
by reassociate the peer. The investigation shows that if move
from legacy to HT, the rate control won't work after changing
the supported rate. But once changing the supported rate to HT,
user can assign the TxRate in HT mode.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A scheduled scan is a more persistent setting and should take priority
over temporary regular scans. Abort the regular when a sched_scan
request arrives and then request the sched_scan.
The kernel API allows sending a sched_scan without canceling a regular
scan in progress, so this is our way to abstract the FW's limitations.
Make the scan-cancel Rx handler async and flush after invocation to
ensure new scans can't creep in before it.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
cfg80211 assumes a scheduled scan is stopped synchronously. Wait for the
FW before returning to caller.
Don't do anything in the async handler in the stop-from-above flow.
There's no need to call the mac80211 sched-scan completion as the
cleanup will be automatic. Make sure the async handler is called before
the next incoming scan changes the scan_status by flushing the async
handlers after all invocations.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Check for both cfg->d0i3 and fw d0i3 support in order
to enable d0i3 support.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
BGN SKU won't scan on 5.2GHz obviously, but the firmware
still expects the driver to reserve space for the the probe
request for the 5.2GHz band.
Fix this by allocating space and leave it empty.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=69541
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When indicating RF-kill toggle to the higher layer, that
may in turn call back to the transport (for MVM at least)
to turn off the device quickly. Instead of that, allow it
to return whether or not the device should be turned off,
this gets rid of the call indirection and will help make
the API more consistent when we go back to non-threaded
interrupts again for PCIe.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
1. Enable LP XTAL to avoid HW bug where device may consume much
power if FW is not loaded after device reset. LP XTAL is
disabled by default after device HW reset. Configure device's
"persistence" mode to avoid resetting XTAL again when SHRD_HW_RST
occurs in S3.
2. Add methods to access SHR (shared block memory space) directly from PCI
bus w/o need to power up MAC HW.
Shared internal registers (e.g. SHR_APMG_GP1, SHR_APMG_XTAL_CFG)can be
accessed directly from PCI bus through SHR arbiter even when MAC HW is
powered down. This is possible due to indirect read/write via
HEEP_CTRL_WRD_PCIEX_CTRL (0xEC) and HEEP_CTRL_WRD_PCIEX_DATA (0xF4)
registers.
Use iwl_write32()/iwl_read32() family to access these registers. The MAC HW
need not be powered up so no "grab inc access" is required.
For example, to read from SHR_APMG_GP1 register (0x1DC),
first, write to the control register:
HEEP_CTRL_WRD_PCIEX_CTRL[15:0] = 0x1DC (offset of the SHR_APMG_GP1 register)
HEEP_CTRL_WRD_PCIEX_CTRL[29:28] = 2 (read access)
second, read from the data register HEEP_CTRL_WRD_PCIEX_DATA[31:0].
To write the register, first, write to the data register
HEEP_CTRL_WRD_PCIEX_DATA[31:0] and then:
HEEP_CTRL_WRD_PCIEX_CTRL[15:0] = 0x1DC (offset of the SHR_APMG_GP1 register)
HEEP_CTRL_WRD_PCIEX_CTRL[29:28] = 3 (write access)
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When power update is initiated on BSS STA while P2P client
exists, the power command will be sent only on BSS STA vif
ignoring P2P client.
Since the firmware has symmetric constraints on the power
save enablement we can simplify the code a bit.
The current firmware doesn't know how to enable power
management on P2P client. Even BSS power management must
be disabled when a P2P client is added.
Future firmware will support power save on BSS and P2P client
as long as they are on different channels.
This was buggy since we didn't disable power management on
P2P client interface if BSS added on the same channel.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
As the antenna dependent fields depend on the firmware file and not
the NVM, use those fields in the VHT capability creation.
Additionally, fix the STBC and antenna pattern consistency fields.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
New firmware enforce valid values for the quota in D3.
The values given to the firmware when suspending and using
WoWLAN where dummy - change them to realistics values.
Tested-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Switch pos to char * which makes the code a bit shorter
as well as other minor cleanups suggested by Joe Perches.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This message triggers on systems that don't support the API,
so suppress them when not debugging as it's not useful to
see it there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Otherwise lockdep complains about the lock, I'm not sure
why we didn't see this before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
PREPARE_[DELAYED_]WORK() are being phased out. They have few users
and a nasty surprise in terms of reentrancy guarantee as workqueue
considers work items to be different if they don't have the same work
function.
Update rt2800usb.c to use INIT_WORK() instead of PREPARE_WORK(). As
the work item isn't in active use during rt2800usb_probe_hw(), this
doesn't cause any behavior difference.
It would probably be best to route this with other related updates
through the workqueue tree.
Only compile tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: linux-wireless@vger.kernel.org
Seems like we have an old bug, where we incidently overwrites
the max_antenna_gain we pass to firmware, with zero value.
End of all we are artifically reducing the output power.
This patch removes the excessive assignment on max_antenna_gain,
which is being provided by regulatory domain, and consequently
improves the tx power.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Consolidate the list of msdu skbs into the msdu-head skb, delete the
rest of the skbs, pass the msdu-head skb on up the stack as normal.
Tested with high-speed TCP and UDP traffic on modified firmware that
supports raw-rx.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It fixes following sparse check warning
>#make C=1 CF=-D__CHECK_ENDIAN__ drivers/net/wireless/mwl8k.o
>drivers/net/wireless/mwl8k.c:3089:6: warning: symbol 'mwl8k_update_survey' was not declared. Should it be static?
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The intstatus in sdio code can be updated from different
threads. To protect intstatus access, atomic functions are
used. One of them is set_bit, but this function is not
guaranteed atomic on all platforms. The loop was replaced
with local created OR function.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit c98db0bec7.
The function atomic_set_mask() is not architecture independent
so it can not be used in the driver as is.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Smatch reports the following:
drivers/net/wireless/rtlwifi/rtl8723be/fw.c:208 _rtl8723be_fill_h2c_command() warn: variable dereferenced before check 'rtlhal' (see line 69)
drivers/net/wireless/rtlwifi/rtl8723be/hw.c:1732 _rtl8723be_read_adapter_info() error: __builtin_memcpy() '&rtlefuse->efuse_map[0][0]' too small (256 vs 512)
The first one is fixed by removing two pointless tests for NULL pointers.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sparse reports the following:
drivers/net/wireless/rtlwifi/rtl8723be/sw.c:374:14: sparse: duplicate const
drivers/net/wireless/rtlwifi/rtl8723be/hw.c:2214:30: sparse: cast to restricted __le32
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch prevents log spamming by adding a case for a previously
unhandled case.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit f78bccd79b entitled "rtlwifi:
rtl8192ce: Fix too long disable of IRQs", Olivier Langlois
<olivier@trillion01.com> fixed a problem caused by an extra long disabling
of interrupts. This patch makes the same fix for rtl8723ae.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit f78bccd79b entitled "rtlwifi:
rtl8192ce: Fix too long disable of IRQs", Olivier Langlois
<olivier@trillion01.com> fixed a problem caused by an extra long disabling
of interrupts. This patch makes the same fix for rtl8188ee.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit f78bccd79b entitled "rtlwifi:
rtl8192ce: Fix too long disable of IRQs", Olivier Langlois
<olivier@trillion01.com> fixed a problem caused by an extra long disabling
of interrupts. This patch makes the same fix for rtl8192se.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit f78bccd79b entitled "rtlwifi:
rtl8192ce: Fix too long disable of IRQs", Olivier Langlois
<olivier@trillion01.com> fixed a problem caused by an extra long disabling
of interrupts. This patch makes the same fix for rtl8192cu.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In a previous commit, Peter Wu removed this call as configure_filter takes care
of setting/clearing RCR_AAP. This patch makes the same change for rtl8723be.
In addition, a change is made in the logging level for one debug printout.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The addition of a driver for the RTL8821AE requires a new API for the
fill_tx_desc() and set_desc() callback routines. This commit makes the
appropriate modifications in all the other drivers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While preparing association request, intersection of device's
VHT capability information and corresponding field advertised
by AP is used.
This patch fixes a couple errors while saving and copying vht_cap
and vht_oper fields from AP's beacon.
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While preparing association request, intersection of device's HT
capability information and corresponding fields advertised by AP
is used.
This patch fixes an error while copying this field from AP's
beacon.
Cc: <stable@vger.kernel.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
the current code is directly setting skb->len, which is not correct and
brings problems with HAVE_EFFICIENT_UNALIGNED_ACCESS enabled in config
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlegacy version of this iwlwifi patch:
commit aed7d9ac18
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date: Wed Feb 20 11:33:00 2013 +0200
iwlwifi: disable 8K A-MSDU by default
Supporting 8K A-MSDU means that we need to allocate order 1
pages for every Rx packet. Even when there is no traffic.
This adds stress on the memory manager. The handling of
compound pages is also less trivial for the memory manager
and not using them will make the allocation code run faster
although I didn't really measure.
Eric also pointed out that having huge buffers with little
data in them is not very nice towards the TCP stack since
the truesize of the skb is huge. This doesn't allow TCP
to have a big Rx window.
See https://patchwork.kernel.org/patch/2167711/ for details.
Note that very few vendors will actually send A-MSDU.
Disable this feature by default.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sparse warns about invalid assignment in
drivers/net/wireless/ti/wl1251/cmd.c:451:42: warning: invalid assignment: |=
drivers/net/wireless/ti/wl1251/cmd.c:451:42: left side has type restricted __le16
drivers/net/wireless/ti/wl1251/cmd.c:451:42: right side has type int
Hence type converted right side to __le16.
Signed-off-by: Surendra Patil <surendra.tux@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The drivers for RTL8723AE and RTL8723BE have some code in common.
This commit copies the common power management routines into the shared
code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The drivers for RTL8723AE and RTL8723BE have some code in common.
This commit copies the common firmware routines into the shared
code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The drivers for RTL8723AE and RTL8723BE have some code in common.
This commit creates a driver for this code that will be shared, and
copies those common routines from rtl8723ae's phy code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A driver for the RTL8723BE will soon be added. This patch adds the
necessary parts to the common headers, and modifies the existing
drivers for those changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A new driver in the rtlwifi family for the RTL8723BE will soon be added.
The bluetooth coexistence code for this device has been split into a separate
mini driver as it will be shared with other devices. This commit adds the
the headers and sources, and modifies Kconfig and Makefile to configure and
build this driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX descriptors are consumed by the HW using DMA.
Even if in the driver code the TX descriptor writes appears before
the HW "dma kick" register writes, the CPU may reorder them.
If this happens, the TX may not happen at all becase the "valid"
descriptor flag may have not been set yet.
This patch adds a write memory barrier to ensures the TX
descriptor is written before writing to the HW "dma kick" register.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX descriptors are consumed by the HW using DMA.
Even if in the driver code the memory write that sets the "valid"
flag appears after all other writes, the CPU may reorder writes,
causing the HW to consider as valid a not-fully-written yet
descriptor.
This may cause HW incorrect behaviour.
This can happen because (AFAIK) the HW may attempt DMA
asynchronously without waiting to be kicked by the following
register write.
This patch adds a write memory barrier to enforce writes ordering.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update of the HW IDs for the 7265 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since the statistics handler is asynchrous, it can very well
be that we will handle the statistics (hence the RSSI
fluctuation) when we already disassociated.
Don't WARN on this case.
This solves: https://bugzilla.redhat.com/show_bug.cgi?id=1071998
Cc: <stable@vger.kernel.org> [3.10+]
Fixes: 2b76ef1308 ("iwlwifi: mvm: implement reduced Tx power")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Smatch suggests to propagate error code from wil_find_cid(), and, indeed,
it is a good idea.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wrong index comparison logic, found by smatch:
drivers/net/wireless/ath/wil6210/debugfs.c:402 wil_txdesc_debugfs_show() warn: buffer overflow 'wil->vring_tx' 24 <= 24
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the current code is directly setting skb->len, which is not correct and
brings problems with HAVE_EFFICIENT_UNALIGNED_ACCESS enabled in config
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previous driver changes to airo, atmel, wl3501_cs, and usb_zd1201 need
to include <net/cfg80211.h>, which depends on CFG80211, so add the
missing dependency.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Older chipsets are more sensitive to high PHY error counts, and the
current noise immunity thresholds were based on tests run at QCA with
newer chipsets.
This patch brings back the values from the old ANI implementation for
old chipsets, and it also disables weak signal detection on an earlier
noise immunity level, to improve overall radio stability on affected
devices.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit 80b4205b "ath9k: Fix OFDM weak signal detection for AP mode"
prevented weak signal detection changes from taking effect in AP mode on
all chipsets, claiming it is "not allowed".
The main reason for not disabling weak signal detection in AP mode is
that typically beacon RSSI is used to track whether it is needed to
boost range, and this is unavailable in AP mode for obvious reasons.
The problem with not disabling weak signal detection is that older
chipsets are very sensitive to high PHY error counts. When faced with
heavy noise, this can lead to an excessive amount of "Failed to stop
TX DMA" errors in the field.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to 802.11n-2012 standard in paragraph PPDU Fromat(20.3.2) HT-mixed
format Hearder PPDU contains : L_STF, L_LTF, L_SIG, HT_SIG, HT_STF, HT_LTF
they are symbols in the preamble, there are in time unit(us) that's for why
it can't be computed in bytes
Signed-off-by: Sylvain ROGER RIEUNIER <sylvain.roger.rieunier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of an explicit cast, use the min_t macro.
Signed-off-by: Silvan Jegen <s.jegen@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using multiple vdevs (stations, aps, etc), it is
nice to be able to associate log messages with specific
interfaces. So, add vdev-id to most logging messages.
Add return code as well, where it was missing.
kvalo: unify some of the messages to follow the same style
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The suspend callback first sets the suspend flag used in the driver
but after that the actual suspend is done, which may fail. Reset the
flag upon suspend failure.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even if the device is changed to 1X1 mode, data is sent with
higher MCS rates after association.
This patch fixes the problem by updating MCS information field
in HT capability when antenna setting changes so that correct
information will be advertised in association and probe request.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Command timeout happens when firmware goes into bad state.
There is no chance that next command will be successful after
this. Hence we will maintain a flag instead of count.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We already have one in mwifiex_adapter structure.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a check in command preparation routine.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of allocating a scatter-gather table for every transmit
reuse a pre-allocated table. The transmit path will be faster by
taking out this allocation.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a mismatch between the mcs index(0-7) reported to cfg80211
and the actual mcs index(0-15) in use. This patch resolves the mismatch
by setting mcs info with the number of chains read from FW.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Deauth is sent to AP when the device is acting as station at
shutdown time. Similarly we should stop AP operation also.
mwifiex_deauthenticate() takes care closing the connection
based on provided interface type.
Add a new function to simplify the code.
Reported-by: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We skip downloading other commands after FUNC_SHUTDOWN is queued
during driver unload. Main thread should be woken up each time
after freeing skipped command so that FUNC_SHUTDOWN gets served
in case if there are other pending commands before FUNC_SHUTDOWN.
Also, call mwifiex_complete_cmd() only for synchronous commands.
Reported-by: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex_cancel_pending_ioctl() and
mwifiex_cancel_all_pending_cmd() are called in command timeout
and driver unload paths respectively.
If scan operation is in progress, we should abort it smoothly.
Reported-by: Tim Shepard <shep@alum.mit.edu>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently default Tx buffer size configured to firmware is 2K
for all chipsets. This patch changes it to 4K for SD/PCIe/USB
8897 chipsets as per firmware requirements.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a race condition while queuing synchronous command and
asynchronous command requested from different threads, because
the wait_q_enabled flag is set based on a global variable
cmd_wait_q_required.
The issue is fixed by removing this global variable and using a
unified function with an argument 'sync' passed into the
function.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Groupcast frames are not subject for BACK reordering because they are not
ACK'ed and one can't request re-transmitt
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
implement del_station() method in the struct cfg80211_ops
It allows to disconnect single peer from the AP
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When notifying about Rx mgmt (ex: during scan), extract
signal strength reported by the hardware.
signal is not MBM, it is arbitrary units 0..100
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Need to fill translation table before calling WMI with WMI_VRING_CFG_CMDID
since firmware may generate events during this call; and events need translation
table filled to be properly dispatched
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disconnect event reported by the FW, should lead to disconnection
of only requested peer. Find for the appropriate CID and disconnect
only it
For AP-like interface, notify cfg80211 with del_sta(),
for the client type interface, disconnect and turn link off.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calculate statistics per connection, report with "iw station dump"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rx stats is not calculated per STA - just give some number
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When FW notifies about BACK status change, it provides ring ID.
Process BA status for requested connection only. As for now, FW
don't report Rx BACK status, it reports Tx one instead.
As per current algorithm used in the firmware, imply Rx BACK
state is in sync with Tx one
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware do not support "real" broadcast on the air.
Use method similar to the Directed Multicast Service (DMS) as
described in the 10.23.15.2 "DMS procedures"
This service copies frame and delivers unicast for each associated peer
Do the following: send original frame to 1-st Tx vring, and send copies
to all other active vrings.
As currently hardware/firmware don't support A-MSDU, convert broadcast
frame to unicast instead of wrapping it in A-MSDU
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are 24 possible Tx vrings; when doind multiple connections, more then
one vring has to be used. Search for free one and select it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When running multiple connections, hardware can't do BACK reordering
and it should be done on the host.
Model after mac80211's implementation. Drop RCU for now;
to be re-added when BACK will be stabilized
BACK handshaking is not implemented yet in the hardware,
pretend it was done to support the way FW operating
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable multiple (up to 8 - HW/FW limitation) simultaneous connections.
Each connection has its own CID (connection ID) that describes chip's
beam-forming entity. Tx Vring should refer to correct CID for frame to reach
its destination.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print '_' for the 'idle' descriptors - this makes vring representation more visible.
Also, for the Tx side, differentiate descriptors having associated skb's - print ones
with skb as 'H' and without as 'h'. Good to represent scattered frames.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Expand debug capabilities to query all Tx/Rx descriptors. Usefull to analyse
various hardware/software stall situations. Printed is whole descriptor content
and the frame itself.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement management frame passing. In order to receive frame on the other
side, remain_on_channel() should be implemented as well
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The intstatus in sdio code can be updated from different
threads. To protect intstatus access, atomic functions are
used. The loop was replaced using atomic_set_mask().
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some stations reset the sequence number for traffic-ids (TIDs)
as they initiate a block-ACK session. In order to detect such
behavior, mwifiex must note the starting sequence number given
during the ADDBA request. If the first received sequence number
after the ADDBA falls outside the receive window for this TID but
after the the ADDBA starting sequence number, we can assume that
this AP has reset its sequence number during the ADDBA. In this
case we must adjust the input window backward to incorporate this
received sequence number instead of ignoring it. Otherwise, we
could fail to successfully retrieve an arbitrarily large number
of downstream frames at the beginning of the block-ACK session.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In time some of the code got redundant, without being noticed.
This patch does not change any functionality, just removes
redundant code.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Immediate sleep support is an aggressive power saving option
that has not been enabled in brcmfmac and is removed to
simplify code.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SDIO dpc scheduling is done (repeated) when counter is set. This
counter gets decreased when dpc is finished. It is more efficient
to set counter to 0 before the dpc is actullay run. This will
minimize the frequency with which dpc is executed.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
First clean up fw signalling, before cleaning up the bus and
proto layer. Old order can cause oops in some circumstances.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The local variable data_len is assigned but never used so get rid
of it.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SDIO driver has a 16-bit field defined in the skbuff control buffer.
However, it is accessed as a u32 overwriting other control info. Another
issue is that the field is not initialized for networking packets, but
the control buffer content is unspecified as other networking layers can
use it.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Internal firmware roaming is enabled by default. This patch
makes it possible to disable internal firmware roaming by
specifying roamoff=1 as module param.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and rename it to ath9k_cmn_setup_ht_cap
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and rename it to ath9k_cmn_init_channels_rates.
sbands are move to ath_common as well.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Survey stats such as channel busy time, rx busy time
and noise are collected when sw_scan starts for every
switched new channel. This happens till sw_scan stops.
All the collected stats are shared up when get_survey()
is called.
This implements support for ACS feature from Hostapd.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement sw_scan start and stop callbacks.
Reset BBP registers for channel, RX busy and
average noise stats which clear on read.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding AP firmware command to access BBP
regs. This will be used for retrieving
different counters CCA/RX needed for ACS
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan} with more
generic ieee80211_{channel_to_frequency, frequency_to_channel}.
File <net/cfg80211.h> has already been included. It's safe to use
IEEE80211_BAND_2GHZ here.
This change is a preparation for the removal of function
ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan} with more
generic ieee80211_{channel_to_frequency, frequency_to_channel}.
Function ieee80211_frequency_to_channel() will return 0 if frequency
is not correctly provided, so no need to set channel to 0 explicitly.
Include <net/cfg80211.h> for the defination of IEEE80211_BAND_2GHZ.
Because <net/cfg80211.h> includes <linux/ieee80211.h>, so we can
replace <linux/ieee80211.h> with <net/cfg80211.h>.
This change is a preparation for the removal of function
ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan} with more
generic ieee80211_{channel_to_frequency, frequency_to_channel}.
File <net/cfg80211.h> has already been included. It's safe to use
IEEE80211_BAND_2GHZ here.
This change is a preparation for the removal of function
ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}.
Cc: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan} with more
generic ieee80211_{channel_to_frequency, frequency_to_channel}.
Include <net/cfg80211.h> for the defination of IEEE80211_BAND_2GHZ.
Because <net/cfg80211.h> includes <linux/ieee80211.h>, so we can
replace <linux/ieee80211.h> with <net/cfg80211.h>.
This change is a preparation for the removal of function
ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}.
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan} with more
generic ieee80211_{channel_to_frequency, frequency_to_channel}.
Include <net/cfg80211.h> for the defination of IEEE80211_BAND_2GHZ.
Because <net/cfg80211.h> includes <linux/ieee80211.h>, so we can
replace <linux/ieee80211.h> with <net/cfg80211.h>.
This change is a preparation for the removal of function
ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}.
Cc: Simon Kelley <simon@thekelleys.org.uk>
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan} with more
generic ieee80211_{channel_to_frequency, frequency_to_channel}.
Include <net/cfg80211.h> for the defination of IEEE80211_BAND_2GHZ.
Because <net/cfg80211.h> includes <linux/ieee80211.h>, so we can
replace <linux/ieee80211.h> with <net/cfg80211.h>.
This change is a preparation for the removal of function
ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Certain HW options (TX packet retry count, CW configuration and
TX power configuration) can be specified in both the TX packet
descriptor and also into HW "global" registers.
The HW is thus configured to honour the global register or the
TX descriptor field depending by the case.
This patch adds few comments that hopefully clarify in which cases
the driver uses one method and in which cases it uses the other.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During driver initialization, some skbs are preallocated for RX.
Currenly if the allocation fails, the driver's allocation routine
exits immediatly but it will return zero (success) anyway.
In this way the driver will continue initialization with buggy
pointers around.
This patch makes the driver's allocation routine to return
an error value and to print a complaint message when skb allocation
fails.
In this way its caller will not go further, avoinding the driver to
successfully load, and preventing dereferencing buggy pointers.
An hint is thus printed about why the driver failed.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During initialization a number of RX skbs are allocated and mapped
for DMA.
Currently if pci_map_single() fails, it will result in passing to the
HW a wrong DMA address (to write to!).
This patch adds check for this condition and eventually causes the
driver not to initialize, avoiding at least dangerous DMAs.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the driver uses pci_iomap() but iounmap() is called in
the error path
Change to use pci_iounmap() instead.
Reported-by: Huqiu Liu <liuhq11@mails.tsinghua.edu.cn>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the contention window enable/disable HW flag is not
touched by the driver.
This patch explicitly set it to the correct value to make sure
contention window is enabled (AFAIK contention window must be
enabled in most (if not all) cases.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add device tree support for the spi variant of wl1251.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for requesting the regulator powering
the vio pin.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the power GPIO handling from the board code into
the driver. This is a dependency for device tree support.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the wl1251 part of the wl12xx platform data structure into a new
structure specifically for wl1251. Change the platform data built-in
block and board files accordingly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As many Surface Pro I & II users have found out, the mwifiex_usb
doesn't support usb autosuspend, and it has caused some system
stability issues.
Bug 69661 - mwifiex_usb on MS Surface Pro 1 is unstable
Bug 60815 - Interface hangs in mwifiex_usb
Bug 64111 - mwifiex_usb USB8797 crash failed to get signal
information
USB autosuspend get triggered when Surface Pro's AC power is
removed or powertop enables power saving on USB8797 device.
Driver's suspend handler is called here, but resume handler
won't be called until the AC power is put back on or powertop
disables power saving for USB8797.
We need to refactor the suspend/resume handlers to support
usb autosuspend properly. For now let's just remove it.
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It doesn't make much sense to calculate the ring
size fill count because it already is memoized in
a separate variable.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
One of the premises was to guarantee serialized
completion handling for upper layers
(HTC/WMI/HTT). Since quite some time now it is no
longer necessary.
The other premise was to batch up tx/rx
completions to take advantage of hot caches.
However frame tx/rx completion indications come in
on a single pipe already so they are already
batched up. More meaningful batching is done in
HTT itself.
This means PCI completion is no longer necessary
to keep around. It just wastes memory, cycles and
SLOC.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is inefficient to grab irqsave spinlocks for
skb lists for each queue/dequeue action.
Using rx_ring.lock and tx_lock allows to use less
heavy bh spinlock functions and moving locking
upwards allows to toggle spinlocks less often.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HTT Rx endpoint processes both frame rx
indications and frame tx completion indications.
Those completions typically come in batches and
may be mixed so it makes sense to defer processing
hoping to get a bunch of them and take advantage
of hot caches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Going through full htc tx path for htt tx is a
waste of resources. By skipping it it's possible
to easily submit scatter-gather to the pci hif for
reduced host cpu load and improved performance.
The new approach uses dma pool to store the
following metadata for each tx request:
* msdu fragment list
* htc header
* htt tx command
The htt tx command contains a msdu prefetch.
Instead of copying it original mapped msdu address
is used to submit a second scatter-gather item to
hif to make a complete htt tx command.
The htt tx command itself hands over dma mapped
pointers to msdus and completion of the command
itself doesn't mean the frame has been sent and
can be unmapped/freed. This is why htc tx
completion is skipped for htt tx as all tx related
resources are freed upon htt tx completion
indication event (which also implicitly means htt
tx command itself was completed).
Since now each htt tx request effectively consists
of 2 copy engine items CE_HTT_H2T_MSG_SRC_NENTRIES
is updated to allow maximum of
TARGET_10X_NUM_MSDU_DESC msdus being queued. This
keeps the tx path resource management simple.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
PCI is capable of handling scatter-gather lists.
This can be used to avoid copying memory.
Change the name of the callback while at to
reflect its purpose.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The flag wasn't used anymore. No need to keep it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no real benefit from using them. DMA-API
already provides debugging. Some skbuffs are
already mapped directly with DMA-API since wrapper
arguments were insufficient and extending them
would be pointless.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After we pass frames with INV_PEER to upper layer in commit 716ae53c56
("ath10k: pass frames with invalid peer status to upper layer") we could pass
some management frames (in case INVALID_PEER and MGMT_CTRL) twice to upper
layer, once via WMI and once via HTT. Next we could handle assoc request twice.
This patch remove such regression.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Indicate spectrum management support in hardware
flags, while we already handle power set
(IEEE80211_CONF_CHANGE_POWER) in the ath10k driver.
This enable 802.11h support for station mode.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Retrieve the mactime of ieee80211_rx_status based on received
data frame. The value is obtained from the htt_rx_indication_ppdu
structure and only available in 32-bit.
kvalo: white space fixes
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Only the first packet is currently handled correctly, but then
all others are assumed to have failed which is problematic. Fix
this, marking them all successful instead (since if they're not
then the firmware will have transmitted them as single frames.)
This fixes the lost packet reporting.
Also do a tiny variable scoping cleanup.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[Add the dvm part]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some APs reject STA association request if a listen interval value exceeds
a threshold of 10. Thus, for example, Cisco APs may deny STA associations
returning status code 12 (Association denied due to reason outside the scope
of 802.11 standard) in the association response frame.
Fixing the issue by setting the default IWL_CONN_MAX_LISTEN_INTERVAL value
from 70 to 10.
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The arsta structure wasn't initialized for
non-ap interfaces. This should fix related
warnings/crashes.
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The nwifi header is padded to 4 bytes. This wasn't
a problem until one tried to (at least) rx 4addr
frames.
This finally allows managed iface to be used in a
bridge.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Makes it easier to determine why some failures
happened.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Implement the get TSF by simply returning 0 so that IBSS
merging is happening. Otherwise, IBSS nodes that have similar
SSID naming won't merge. This is simply fooling the mac80211
that the TSF in the received beacon is higher than the local TSF.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Only set sc->rx.discard_next to rx_stats->rs_more when actually
discarding the current descriptor.
Also, fix a detection of broken descriptors:
First the code checks if the current descriptor is not done.
Then it checks if the next descriptor is done.
Add a check that afterwards checks the first descriptor again, because
it might have been completed in the mean time.
This fixes a regression introduced in
commit 723e711356
"ath9k: fix handling of broken descriptors"
Cc: stable@vger.kernel.org
Reported-by: Marco André Dinis <marcoandredinis@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check if the baseband state remains stable, and add a small delay
between register reads.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only one channel is returned - the one currently being used.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some chips, baseband watchdog hangs are more common than others, and
the driver has support for handling them.
Interrupts even after a watchdog hang are also quite common, so there's
not much point in spamming the user's logfiles.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
5/10 MHz channel bandwidth is configured via the PLL clock, instead of
the AR_PHY_MODE register. Using that register is AR93xx specific, and
makes the mode incompatible with earlier chipsets.
In some early versions, these flags were apparently applied at the wrong
point in time and thus did not cause connectivity issues, however now
they are causing problems, as pointed out in this OpenWrt ticket:
https://dev.openwrt.org/ticket/14916
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trivially reduces text size too.
$ size drivers/net/wireless/ath/ath9k/debug.o*
text data bss dec hex filename
34436 2528 5128 42092 a46c drivers/net/wireless/ath/ath9k/debug.o.new
34464 2528 5128 42120 a488 drivers/net/wireless/ath/ath9k/debug.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Number of MAC hangs and stuck beacons were missing
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PREPARE_[DELAYED_]WORK() are being phased out. They have few users
and a nasty surprise in terms of reentrancy guarantee as workqueue
considers work items to be different if they don't have the same work
function.
Update rt2800usb.c to use INIT_WORK() instead of PREPARE_WORK(). As
the work item isn't in active use during rt2800usb_probe_hw(), this
doesn't cause any behavior difference.
It would probably be best to route this with other related updates
through the workqueue tree.
Only compile tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even if we mark PS on, device still worked in normal mode. Patch
corrects that and now we send proper powertable command to device,
which put it in sleep mode when PS is on.
Reported-and-tested-by: Tino Keitel <tino.keitel@tikei.de>
Tested-by: Pedro Francisco <pedrogfrancisco@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge reclaim check for 3945 & 4965. This add some more checks for
3945, most importantly N_RX notify.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have only 5 tx queues on 3945, updating il->txq[5] results in
writing random value to HBUS_TARG_WRPTR register.
Additionally use spin lock to protect txq->write_ptr and
txq->need_update fields also modified in TX path.
Tested-by: Pedro Francisco <pedrogfrancisco@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't perform OBSS scan internally. As we intend to use
corresponding feature in application, we will enable this flag.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While modifying timer, we need not delete timer.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use SMP safe del_timer_sync instead of del_timer for cancelling
timers.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 handles the actual operations, so ath9k can just indicate
support for this. Based on initial tests, this combination seems to
work fine.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
removed following warnings-
drivers/net/wireless/airo.c:39: WARNING: Use #include <linux/io.h> instead of <asm/io.h>
drivers/net/wireless/airo.c:48: WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
Signed-off-by: Avinash Kumar <avi.kp.137@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a relatively old Prism2 card which is correctly supported
by the hostap driver.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Logically, config B43_BCMA_PIO should depend on B43. This also solves
the problem that sub options of b43 driver didn't indent correctly in
make menuconfig's ncurses window.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 0baa0fd76f
("rtlwifi: Convert core routines for addition of rtl8192se and
rtl8192de") removed setting HW_VAR_RCR, HW_VAR_MGT_FILTER and
HW_VAR_CTRL_FILTER. The last two are probably done because some hardware
does not support them. The first is probably a mistake. This patch adds
the missing set_hw_reg call.
For PCI support, rx_conf is not touched directly. Instead, get_hw_reg is
used to abstract between receive_config (for PCI) and rx_conf (for USB).
This was tested on a 10ec:8176 Realtek RTL8188CE (according to the
label on the mini-PCIe card). Before this patch, `iw wlan0 set monitor
otherbss` did not capture frames from other BSS's. After this patch, it
does print packets.
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rtl*_set_check_bssid functions are mostly the same, but access the
RCR register in different ways. Use the get_hw_reg abstraction layer
(which reads rtlpci->receive_config for PCI devices and mac->rx_conf for
USB).
There is no functional change for cases where receive_config was
accessed directly. For rtl8192ce, there is still no change because
nothing modifies REG_RCR or receive_config. For rtl8192cu, it now also
applies changes to rx_conf from configure_filter, but that can be
considered a bug which is fixed later.
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a typo here because the names are confusingly similar. The
intent was sizeof(struct ieee80211_vht_cap) (size 12) but sizeof(struct
ieee80211_ht_cap) (size 32) was used.
Anway, it's cleaner to just specify the variable instead of the type.
Fixes: 5f6d598339 ('mwifiex: add VHT support for TDLS')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When passing tx frames to the U-APSD queue for powersave poll responses,
the ath_atx_tid pointer needs to be passed to ath_tx_setup_buffer for
proper sequence number accounting.
This fixes high latency and connection stability issues with ath9k
running as AP and a few kinds of mobile phones as client, when PS-Poll
is heavily used
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both libertas USB driver and mwifiex_usb driver are registerring
with name 'usb8xxx'. The following conflict happens while trying
to load both drivers.
[6.211307] Error: Driver 'usb8xxx' is already registered...
[6.217261] mwifiex_usb: Driver register failed!
Fix it by renaming mwifiex_usb driver's name.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use the TLV flags as a handshake between the firmware
and the driver. These flags allow the firmware to advertise
its capabilities and API version.
Since we are running short of bits, we add a new
infrastructure which is more scalable, yet backward
compatible.
We make now the difference between API changes and the
capabilities. Both can have an index which allows to scale
at will.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This define is a leftover from dvm (in mvm, it
was replaced by MVM_UCODE_ALIVE_TIMEOUT).
Signed-off-by: Inbal Hacohen <Inbal.Hacohen@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These values aren't used as the firmware values should be used,
so reading them is pointless and hides potential errors when
somebody uses these values. Leave them zero to make it clearer
that they can't be used. We can't remove the struct members as
the DVM driver does read the values from EEPROM/OTP and the
structure is shared between drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The minimum CCA power threshold values have to be adjusted
for existing cards to be in compliance with new regulations.
Newer cards will make use of the values obtained from EEPROM,
support for this was added earlier. To make sure that cards
that are already in use and don't have proper values in EEPROM,
do not violate regulations, use the initvals instead.
Cc: stable@vger.kernel.org
Reported-by: Jeang Daniel <dyjeong@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver concatenates multiple packets in one MMC transfer. For
scatter-gather to work the total length need to be multiple of 512
bytes. A pre-allocated buffer was used to add padding to accomplish
that. However, the length was not properly set and it was freed after
the first transfer causing a crash.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are sending sleep confirm done interrupt in the middle of
sleep handshake. There is a corner case when Tx done interrupt
is received from firmware during sleep handshake due to which
host and firmware power states go out of sync causing cmd and
Tx data timeout problem.
Hence sleep confirm done interrupt is sent at the end of sleep
handshake to fix the problem.
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We may get a NULL pointer here if skb allocation for Rx packet
was failed earlier.
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Write io memory to clean PCIe buffer only when PCIe device is
present else this results into crash because of invalid memory
access.
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Scan results from Marvell 8388 and 8686 have probe responses from
hidden APs and OLPC XO-1 mesh with a zero length SSID IE.
Bug in lbs_ret_scan discarded any remaining BSS in scan response,
leading to user not seeing APs in dense environments.
With LBS_DEB_SCAN, dmesg shows
libertas scan: scan response: 5 BSSs (419 bytes); resp size 474 bytes
libertas scan: scan: 00:1a:2b:84:de:e8, capa 0401, chan 1, qz, -51 dBm
libertas scan: scan: 5c:63:bf:d8:eb:0c, capa 0411, chan 1, qw129, -23 dBm
libertas scan: scan response: invalid IE fmt
With LBS_DEB_HEX, dmesg shows valid BSS in scan response were not
processed.
Change is to ignore zero length IE and continue processing.
Fixes OLPC 12757, http://dev.laptop.org/ticket/12757
Signed-off-by: James Cameron <quozl@laptop.org>
Reported-by: T Gillett <tgillett@gmail.com>
Tested-by: T Gillett <tgillett@gmail.com>
CC: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Function del_timer() does not guarantee that timer was really deleted.
If the timer handler is beeing executed at the moment, the function
does nothing. So, it's possible to use already freed memory in the handler:
[ref: Documentation/DocBook/kernel-locking.tmpl]
This was found using grep and compile-tested only. Please, consider
applying or something similar to it.
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
CC: Jouni Malinen <j@w1.fi>
CC: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Collect statistics regarding rates and aggregations in Rx
frames and export the data via debugfs.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Newer firmware support a new bit in the policy that allows
to request to apply the time event immediately. Add this bit
without removing the workarounds we used until now to support
older firmares.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case the firmware didn't assert but we want to restart
it, e.g. we didn't get the reply for a host command, or the
Tx queues are stuck, we should stop the firmware by
provoking an interrupt. This allows to better debug the
firmware in these bad scenarios.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We set IWL_STA_UCODE_INPROGRESS flag when we add a station
and clear it when we send the LQ command for it. But the LQ
command is sent only when the association succeeds.
If the association doesn't succeed, we would leave this flag
set and that wouldn't indicate the station entry as vacant.
This probably fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=1065663
Cc: <stable@vger.kernel.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In order to solve races with sched_scan_stop, it is necessary
for the driver to be able to return an error to propagate that
to cfg80211 so it doesn't send an event.
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct
the VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the
presence of the respective IEs in the received TDLS Setup Response frame.
The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.
Signed-off-by: Sunil Dutt Undekari <usdutt@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: wil6210@qca.qualcomm.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new argument for ndo_select_queue() callback that passes a
fallback handler. This gets invoked through netdev_pick_tx();
fallback handler is currently __netdev_pick_tx() as most drivers
invoke this function within their customized implementation in
case for skbs that don't need any special handling. This fallback
handler can then be replaced on other call-sites with different
queue selection methods (e.g. in packet sockets, pktgen etc).
This also has the nice side-effect that __netdev_pick_tx() is
then only invoked from netdev_pick_tx() and export of that
function to modules can be undone.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows dynamic changes of bandwidth/nss/smps,
e.g. via ht/vht operation mode change
notification.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware ignores SMPS flags in peer assoc command.
For SMPS to work it is necessary to set peer
parameter after peer assoc command so that tx
chainmask is setup properly.
This should fix packet loss and improve throughput
with stations that have SMPS enabled upon
association.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
I modified Michal's commit c930f744bd ("ath10k: implement channel switching") to return
when vdev_start() fails, but forgot to release conf_mutex.
Found by coccinelle:
>> drivers/net/wireless/ath/ath10k/mac.c:2745:5-11: preceding lock on line 2663
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes a checkpatch warning in ath10k:
drivers/net/wireless/ath/ath10k/mac.c:1636: WARNING: Avoid CamelCase: <regpair->regDmnEnum>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix a checkpatch warning:
drivers/net/wireless/ath/ath10k/debug.h:95: CHECK: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The dtim period sent to FW was 0 because the dtim period
was never set. This caused an incorrect dtim count to be sent in
beacons.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes problems seen with multiple softap clients and reconnecting
softap clients.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is more line with the names of the other members
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3680 has a few registers on other addresses.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After fw caps exchange, print the FW's capabilities.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If wowlan if off mac80211 will stop / start the driver on suspend /
resume. This causes problems on resume since request_firmware is called
from start. Fix this by caching the nv.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some wcnss firmwares the start command can take up to 300ms to
complete. Currently there is a 200ms timeout for SMD command to
complete which causes the start to fail.
Increase the timeout to 500ms. Also improve debug information
regarding SMD command completion time.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Response format is not in the canonical format.
wcn36xx_smd_rsp_status_check cannot be used.
* Save the FW caps in wcn36xx struct for later use.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TI wl12xx/wl18xx cards support channel switch via a driver specific
switch_channel op while operating with channel contexts.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling beacon filtering before receving a beacon
might result in not having a beacon at all for the
current connected AP, which prevents the station
from entering power-save.
Replace the current approach (of starting beacon
filtering on init) and configure beacon filering
only after bss_conf->dtimper is set (which means
mac80211 already parsed a beacon).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dfs configuration command might take longer than
the current timeout. increase it to 5 seconds.
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Silently ignore repetitive scheduling of recovery work and commands
being passed to the bus when the HW is not available. This can happen
many times during recovery and slow it down. It also spams the kernel
logs.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each AP has its own global and broadcast links, so when
checking for active sta count (according to the active_link_count)
we must take them all into account.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 unsets the default wep key on disassoc.
The fw doesn't support this notification, so simply
ignore it.
The actual flow actually triggers fw recovery in some
cases, as mac80211 unsets the default key only after
disassoc, when wlvif->sta.hlid, resulting in invalid
hlid being passed to the fw.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12xx chips allow only OFDM rates in AP mode for BT-Coex purposes. This
is no longer required in 18xx chips, starting with FW 8.6.0.0.8.
Update the min allowed FW version in 18xx to support this functionality.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stopping sched scan on interface removal (during recovery)
is no longer needed, as sched scanning is automatically
restarted by mac80211.
Signed-off-by: Barak Bercovitz <barak@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send EAPOL frames with voice priority by setting (the new)
TX_HW_ATTR_EAPOL_FRAME bit in tx attribute.
Sending EAPOL with voice priority fixes re-key
timeout issues during heavy traffic.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bump the min wl18xx fw version to 8.8.0.0.13
This fw is not backward compatible with older
firmware (due to api changes), so use bump
the firmware name as well.
Some modifications were done to the driver-fw api
in order to support multiple APs.
Additionally, some of the consts (such as max stations,
max links and max RX BA sessions) were changed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each hw supports a different iface combinations.
Define the supported combinations in each driver,
and save it in wl->iface_combinations.
Since each driver defines its own combinations now,
it can also define its max supported channels, so
we no longer need to save and set it explicitly
in wlcore.
Update wl18xx interface combinations to allow
multiple APs.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each hw supports a different max stations (connected to the
same ap). add a new wl->max_ap_stations and use it instead
of the current common AP_MAX_STATIONS.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upcoming fw versions will have different max links support
(according to the hw). Get ready for it by configuring
wl->num_links per-hw, instead of using the const WL12XX_MAX_LINKS.
However, continue using WLCORE_MAX_LINKS in order to simplify
structs declarations (we use it in multiple bitmaps, and converting
them to dynamic arrays is just cumbersome).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of splitting the fw_status into 2 and using some
complex calculations, read the fw status and let each low-level
driver (wl12xx/wl18xx) convert it into a common struct.
This is required for the upcoming fw api changes, which
break the current logic anyway.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems the wl18xx FW sometimes sends spurious changes on the PSM state
of the broadcast HLID. This causes us to search for a station on a
non-peer link and fail, causing warnings in our log.
Prevent the driver from considering PSM changes for any non-peer HLIDs.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the chip is in ELP mode read/write to FW is invalid and may cause
the lower layers to get stuck. The reads/writes concerning ELP wakeup
are the exception here and are checked for. In addition to blocking the
IO, produce a warning.
Signed-off-by: Barak Bercovitz <barak@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes a tx_flush during suspend fails, but the FW manages to flush
out the packets during the time when the host is supsended. Cancel
the Tx-watchdog on suspend to not cause a spurious recovery on resume
for that case. Set a flag to reinit the watchdog on the first Tx after
resume, so we'll still recover if the FW is not empty and there's
indeed a problem.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zero rx_filter_enabled array after recovery to avoid
cases were the driver will keep trying to clear a
filter which is not configured in FW.
Such case will cause consecutive recoveries due to
command execution failures.
While on it, convert rx_filter_enabled to bitmap,
to save some memory and make sparse happy (it
doesn't like sizeof(bool array)).
Signed-off-by: Nadim Zubidat <nadimz@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ieee80211_channel_to_frequency() to replace b43_channel_to_freq_{2,5}ghz(),
and remove unused b43_freq_to_channel_{2,5}ghz().
Signed-off-by: ZHAO Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
remove_proc_subtree() doesn't work here as local->ddev has already
been removed, and NULLed out. Use proc_remove() instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes regression caused by commit a16dad7763 "MIPS: Fix
potencial corruption". That commit fixes one corruption scenario in
cost of adding another one, which actually start to cause crashes
on Yeeloong laptop when rtl8187 driver is used.
For correct DMA read operation on machines without DMA coherence, kernel
have to invalidate cache, such it will refill later with new data that
device wrote to memory, when that data is needed to process. We can only
invalidate full cache line. Hence when cache line includes both dma
buffer and some other data (written in cache, but not yet in main
memory), the other data can not hit memory due to invalidation. That
happen on rtl8187 where struct rtl8187_priv fields are located just
before and after small buffers that are passed to USB layer and DMA
is performed on them.
To fix the problem we align buffers and reserve space after them to make
them match cache line.
This patch does not resolve all possible MIPS problems entirely, for
that we have to assure that we always map cache aligned buffers for DMA,
what can be complex or even not possible. But patch fixes visible and
reproducible regression and seems other possible corruptions do not
happen in practice, since Yeeloong laptop works stable without rtl8187
driver.
Bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=54391
Reported-by: Petr Pisar <petr.pisar@atlas.cz>
Bisected-by: Tom Li <biergaizi2009@gmail.com>
Reported-and-tested-by: Tom Li <biergaizi2009@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Larry Finger <Larry.Finger@lwfinger.next>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the original code we shift "AR5K_PHY(256) >> 28" which is zero but
the intent was to shift the return value of ath5k_hw_reg_read() like we
do a couple lines later.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl_ps_enable_nic() is called from loops that will loop until this function returns true or a
maximum number of retries is performed.
hw_init() returns non-zero on error. In that situation return false to
restore the original design intent to retry hw init when it fails.
Signed-off-by: Olivier Langlois <olivier@trillion01.com>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl8192ce is disabling for too long the local interrupts during hw initiatialisation when performing scans
The observable symptoms in dmesg can be:
- underruns from ALSA playback
- clock freezes (tstamps do not change for several dmesg entries until irqs are finaly reenabled):
[ 250.817669] rtlwifi:rtl_op_config():<0-0-0> 0x100
[ 250.817685] rtl8192ce:_rtl92ce_phy_set_rf_power_state():<0-1-0> IPS Set eRf nic enable
[ 250.817732] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.817796] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.817910] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818024] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818139] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818253] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818367] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:98053f15:10
[ 250.818472] rtl8192ce:rtl92ce_sw_led_on():<0-1-0> LedAddr:4E ledpin=1
[ 250.818472] rtl8192c_common:rtl92c_download_fw():<0-1-0> Firmware Version(49), Signature(0x88c1),Size(32)
[ 250.818472] rtl8192ce:rtl92ce_enable_hw_security_config():<0-1-0> PairwiseEncAlgorithm = 0 GroupEncAlgorithm = 0
[ 250.818472] rtl8192ce:rtl92ce_enable_hw_security_config():<0-1-0> The SECR-value cc
[ 250.818472] rtl8192c_common:rtl92c_dm_check_txpower_tracking_thermal_meter():<0-1-0> Schedule TxPowerTracking direct call!!
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> rtl92c_dm_txpower_tracking_callback_thermalmeter
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Readback Thermal Meter = 0xe pre thermal meter 0xf eeprom_thermalmeter 0xf
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Initial pathA ele_d reg0xc80 = 0x40000000, ofdm_index=0xc
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Initial reg0xa24 = 0x90e1317, cck_index=0xc, ch14 0
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Readback Thermal Meter = 0xe pre thermal meter 0xf eeprom_thermalmeter 0xf delta 0x1 delta_lck 0x0 delta_iqk 0x0
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> <===
[ 250.818472] rtl8192c_common:rtl92c_dm_initialize_txpower_tracking_thermalmeter():<0-1-0> pMgntInfo->txpower_tracking = 1
[ 250.818472] rtl8192ce:rtl92ce_led_control():<0-1-0> ledaction 3
[ 250.818472] rtl8192ce:rtl92ce_sw_led_on():<0-1-0> LedAddr:4E ledpin=1
[ 250.818472] rtlwifi:rtl_ips_nic_on():<0-1-0> before spin_unlock_irqrestore
[ 251.154656] PCM: Lost interrupts? [Q]-0 (stream=0, delta=15903, new_hw_ptr=293408, old_hw_ptr=277505)
The exact code flow that causes that is:
1. wpa_supplicant send a start_scan request to the nl80211 driver
2. mac80211 module call rtl_op_config with IEEE80211_CONF_CHANGE_IDLE
3. rtl_ips_nic_on is called which disable local irqs
4. rtl92c_phy_set_rf_power_state() is called
5. rtl_ps_enable_nic() is called and hw_init()is executed and then the interrupts on the device are enabled
A good solution could be to refactor the code to avoid calling rtl92ce_hw_init() with the irqs disabled
but a quick and dirty solution that has proven to work is
to reenable the irqs during the function rtl92ce_hw_init().
I think that it is safe doing so since the device interrupt will only be enabled after the init function succeed.
Signed-off-by: Olivier Langlois <olivier@trillion01.com>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As result deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case IRQ configuration is unknown possibly enabled MSIs
are left enabled in ath10k_pci_deinit_irq(). This update
fixes the described misbehaviour.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The documentation states that pci_enable_msi_block() returns the number of
requests 'could have been allocated', not 'could allocate'. IOW, MSIs are *not*
enabled if a positive value returned.
kvalo: add commit log based on Alexander's email
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass frames with invalid peer status to upper layer.
Next mac80211 will validate frames and drop if required.
This is required to detect spurious frames and pass
this info to user mode (detect CLASS2 CLASS3 frames from
nonauthenticated/nonassociated stations).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is a workaround for HT-enabled STAs which break the spec
and have no HT capabilities RX mask (no HT RX MCS map).
As per spec, in section 20.3.5 Modulation and coding scheme (MCS),
MCS 0 through 7 are mandatory in 20MHz with 800 ns GI at all STAs.
Firmware asserts if such situation occurs.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of warm reset target need to be suspended.
Suspend function is extented to handle both cases
with disabling interrupts and without disabling interrupts.
Warm target reset requires suspend with all interrupts
disabled.
This patch depends on
ath10k: fix device initialization routine
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Suspend/resume callbacks are not protected by configuration mutex
so adding such protection. Also in order to simplify implemetation
of suspend function wait queue is replaced by completion.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Hardware CUS232 version 2 has some issues with cold
reset that lead to Data Bus Errors or system hangs
in some cases. It's safer to use warm reset when
possible as it shouldn't trigger the
aforementioned issues.
Prefer warm reset over cold reset. However since
warm reset doesn't work after FW crash make sure to
fallback to cold reset when booting up the HW.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was found during testing the nss calculation does not
cover all corner cases. Station could request eq. only MCS8
and MCS9 (nss=2 specific). Next num_rates=2 so the driver
sets nss=(max((2+7)/8, 1))=1. Which is wrong. The in-driver
calculation was introduced prior (commit ddcc347b70
mac80211: fix rx_nss calculation for drivers with hw rc).
Since it's fixed, use mac80211 provided value from now.
End user will experience lower throuhputs than expected
if the nss is wrongly calculated.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This throw a lot of pointless warnings in case of DFS (radar
detection) and PHYERR events from firmware, when firmware may
actually insert more data, than we assume.
Besides of being noisy this debug does not protect or check
anything usefull currently. It was introduced long time ago
while debugging aggregations. So just removing it.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Show message length and expected length. Helps debug
firmware mismatch issues.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
NICs supported by iwldvm don't handle well TX AMPDU.
Disable it by default, still leave the possibility to
the user to force enable it with a debug parameter.
NICs supported by iwlmvm don't suffer from the same issue,
leave TX AMPDU enabled by default for these.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The new API for ALIVE notification was misunderstood.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These inlines are pretty pointless now as they just return a
fixed struct value, remove them - the code even gets shorter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Support the changes below:
- Fields and sections structure were changed.
- the NVM file built from DWord instead of Words.
- sections header format was changed.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
New FW enables support for power save on BSS and P2P client MACs
simultaneously when they function on different channels (DCM).
Enable this case in the driver after examining new TLV flag -
IWL_UCODE_TLV_FLAGS_BSS_P2P_PS_DCM. Still power management is not
allowed on both MACs if they function on a same channel.
Remove another redundant TLV flag - IWL_UCODE_TLV_FLAGS_P2P_PS that
is not in use anymore. Remove bound_vif_cnt as redundant.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow reading/writing prph registers.
The address is set in the first argument
of the write operation. second argument
is optional and can be used for writing.
e.g.
echo '0xA01234 0x99' > /sys/kernel/debug/ieee80211/phy0/iwlwifi/iwlmvm/prph_reg
will write 0x99 into reg 0xA01234
cat /sys/kernel/debug/ieee80211/phy0/iwlwifi/iwlmvm/prph_reg
will show its current value (probably 0x99)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of checking the SKB protocol against EAP, check the
IEEE80211_TX_CTRL_PORT_CTRL_PROTO flag that more generally
indicates whether or not the frame is a port control frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This will allow to get sniffer captures with correct
settings for these HT / VHT capabilities.
Also set the corresponding HAVE_MCS / VHT_KNOWN bits in
the registration to mac80211.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There are a number of things in the .data section that should
really be in .rodata, for example all ops structs and strings.
Mark everything const that can be, leaving the .data section
pretty much empty.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The various code blocks in iwl_pcie_[rt]xq_inc_wr_ptr
finally do the same things, so just merge them
all and make the functions cleaner.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch adds key material V2 support to mwifiex.
Newer FW supports this feature and FW KEY API version is used
to determine which command structure needs to be used.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to parse FW API version TLVs.
Currently only API version for key_material is supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During deauthenticate/link lost event, disable all TDLS links as
TDLS would not work when infra connection is not active.
Also this will avoid an issue where ping to peer station doesn't
work after reassociation to AP where we had created TDLS link in
earlier association.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If TDLS link is 11ac enabled i.e. we as well as peer station
supports VHT, configure seprate TX & RX window sizes during
BA setup. So even if BSS does not support 11ac, we can use VHT
capabilities and higher window sizes on direct link.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During TDLS setup request/response, if HW is 11ac capable,
we add VHT Capability IEs in outgoing data frame. Also while
processing received setup request/response, we preserve peer's
11ac capability retrieved from IEs.
Patch also gets VHT parameters from config_station handlers and
sets it to FW using TDLS config command.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mwifiex_fill_vht_cap_tlv function to pass
struct ieee80211_vht_cap instead of mwifiex_ie_types_vhtcap
so that it can be used generically.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds AMPDU support for TDLS link. We have set 11n
capabilities including AMPDU parameters during ENABLE_LINK.
We set a variable in RA list to indicate this as TDLS link.
This patch uses these capabilities to know if AMPDU is allowed
on TDLS link and enables AMPDU aggregation for TX and RX reording
support for RA list for this peer.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1. If data packet is addressed to TDLS peer for which link is
established, mark these packets with TDLS flag so that FW can
send them on direct link instead of sending via AP.
2. If data packet is addressed to TDLS peer and TDLS setup is
underway, move these packets to TDLS queue.
3. If this packet is TDLS setup packet, do not block it.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While TDLS link is being setup, few packets from this station to
peer station may be buffered at AP. It may happen that once TDLS
link is setup, packets sent from station to peer on direct link
get delivered before traffic from AP arrives at peer station.
This results into packet reordering issue at peer station.
To avoid this, we hold data packets destined to TDLS peer during
TDLS setup. These packets are moved to temperory TDLS TX queue.
Upon successful TDLS setup, they are moved to RA list created for
this peer. Upon failure, packets are moved back to AP's RA list
for that particular TID.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds cfg80211 change_station handler support for mwifiex
which is needed for TDLS link setup. Driver creates a command to
modify peer link capabilities and issues command to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds cfg80211 add_station handler support for mwifiex
which is needed for TDLS setup. Driver issues create TDLS link
command to FW upon receiving add_station from cfg80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds cfg80211 handler tdls_oper handler support to
mwifiex. Upon enable link, driver sets status as TDLS status as
setup complete and also sets AMSDU size, AMPDU params for direct
link. Upon disable link, driver issues command to FW to delete
this link in FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for parsing TDLS action frames during
station receive handler.
Peer station capabilities are stored into station node.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for TDLS management frames transmit
handler. mwifiex driver supports TDLS with external support,
i.e. expects user space application to form TDLS frames.
Same is advertised to cfg80211 during registration.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass 'struct ieee80211_ht_cap' pointer to
mwifiex_fill_cap_info() instead of
'struct mwifiex_ie_types_htcap' pointer, because the routine
internally uses the later one.
This patch also adds WARN_ON_ONCE check for NULL band.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These functions are now needed by TDLS while managing station list.
Move them from AP related file to utility file.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tos_to_tid_inv values are needed even during TDLS restore
operations. Currently tos_to_tid_inv is part of wmm.c and
is declared static.
Make it part of private structure so that it can be used in
other files as well.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug where we were checking for AP's AMPDU param
setting even when transmitting traffic to associated station.
Patch adds provision to pass additional parameter ra_list pointer
to function which checks if AMPDU is allowed. If current BSS type is
AP, we check station's AMPDU params else we check AP's AMPDU params.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently MU/SU beamformer and MU beamformee features are
not supported.
Hence this patch modifies VHT capability information accordingly.
Number of sounding dimensions should be zero in this case.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes sure that beamforming capability field in
ht capability info gets filled if hardware supports the feature.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current mwifiex pcie driver assumed that it would get
its cmdrsp_complete() callback called before another command
was sent to unmap the command's skbuff. However, that is not
true. The mwifiex_check_ps_cond() will send a sleep command
to the card without having adapter->curr_cmd set. Within the
workqueue's state machine the adapter's state would be set
to allow commands (curr_cmd = NULL && cmd_sent = false) after
having receieved the response from the sleep command. The
card->cmd_buf would then be overridden with the new command
but the first command's skbuff was not unmapped. This leaks
mapped skbuffs when a bounce buffer is employed.
To rectify this unmap the card->cmd_buf when the response is
received from the card instead of waiting for the
cmdrsp_complete() callback.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Stewart <pstew@chromium.org>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Depending on the underlying DMA implementation its
not possible to partially unmap DMA buffers. Moreover
its not possible to understand the intent of passing
0 as the size to dma unmap. The intent of this
driver is unmap the entire skb buffer. The only way
to ensure that the size matches on unmap is to store
both the dma address and the size in the skb ca field.
Introduce a mwifiex_dma_mapping structure which tracks
the dma address and the size. Additionally, provide
a mwifiex_unmap_pci_memory() that utilizes the new
structure. This also provide symmetry within the
internal API.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Stewart <pstew@chromium.org>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In extended scan, host gets scan results through one or
multiple events instead of scan command response. Host will
send next scan command when all the events are received.
Legacy scan sometimes truncates scan results in a noisy
environment due to buffer length limitation. This issue
is addressed in extended scan.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This new function will be useful later for extended scan
feature.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This new function will be useful later for extended scan
feature.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'mwifiex_bcn_param' structure contains five parameters which
are present in beacon buffer in case of legacy scan.
'rssi' field won't be there in this buffer for extended scan.
Hence 'bssid' and 'rssi' are removed from the structure and it is
renamed as 'mwifiex_fixed_bcn_param' so that we can have common
parsing logic later for both.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bit12 in fw_cap_info is for testing only.
Remove all related code.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) rename max_mcs to mcs;
2) initialize 'i' and 'nss' as 1 instead of 0 in nss lookup;
3) use GET_VHTNSSMCS(mcs_map, nss) macro;
4) use IEEE80211_VHT_MCS_* definitions instead of hard coding
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove these local array variables and define them as static
const array in global space.
The duplicated mcs_rate table is removed automatically with this
change.
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove driver's macro and use ieee80211's definition instead
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a routine to calculate the median IQ correction
values for AR955x, which is used for outlier detection.
The normal method which is used for all other chips is
bypassed for AR955x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be used for storing data for mutiple
IQ calibration runs, for AR955x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IQ calibration post-processing for AR955x is different
from other chips - instead of just doing it as part
of AGC calibration once, it is triggered 3 times and
a median is determined. This patch adds initial support
for changing the calibration behavior for AR955x.
Also, to simplify things, a helper routine to issue/poll
AGC calibration is used.
For non-AR955x chips, the iqcal_idx (which will be used
in subsequent patches) is set to zero.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect values are programmed in the registers
containing the IQ correction coefficients by the IQ-CAL
post-processing code. Fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ar9003_hw_tx_iq_cal_outlier_detection instead.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In chips like AR955x, the initvals contain the information
whether IQ calibration is to be done in the HW when an
AGC calibration is triggered. Check if IQ-CAL is enabled
in the initvals before flagging 'txiqcal_done' as true.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calibration data is not reused for SoC chips, so
call ar9003_hw_tx_iq_cal_post_proc() with the correct
argument. The 'is_reusable' flag is currently used
only for PC-OEM chips, but it makes things clearer to
specify it explicity.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Buffalo WLI-UV-AG300P is almost the same as Sony UWA-BR100.
Signed-off-by: Masaki TAGAWA <masaki@club.kyutech.ac.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no benefit in retaining the legacy rate control module
in the driver codebase.
It is known to be buggy and has less than optimal performance
in real-world environments compared with minstrel. The only
reason that it was kept when we made the switch to minstrel
as default was that it showed higher throughput numbers in a
clean/ideal environment.
This is no longer the case and minstrel can push ath9k to
the same throughput levels. In TCP, with 3-stream cards, more than
295 Mbps can be obtained in open air, with 2-stream cards,
210 Mbps is easily reached. To test performance issues,
instead of using a broken rate control module, it is better
to use the fixed-rate interface provided by mac80211 anyway.
The ath9k RC has not received any bug fixes in years and is
just bit-rotting away - this patch removes it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
after switch to common fucntions we do not need this memcpy any more.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and rename it to ath9k_cmn_rx_skb_postprocess. We will use it
on ath9k_htc.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we can reuse this function in ath9k_htc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we can reuse this fucntion on ath9k_htc.
Now we will need to use common version last_rssi, so switch
it too.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we need access to this variable from common functions.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On commit 28f2bce9f8 I make change that
print various messages as default. This can cause flood of messages
related to TX status timeout on some environments. I partially fixed
problem on commit bb9c298f31, but forgot
to move two more messages to debug level.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the enter and exit download sequence the chip core info was checked
for presence of CM3 ARM core. If found it would enter download state for
the CM3. However, on devices that have a CM3 and CR4 this is not correct
and the CR4 should be used to enter download state. This patch changes
the ARM core lookup giving CR4 precedence.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcmf_add_keyext() is for setting per-station key for cipher
algorithms such as WPA1/WPA2 and should not be used to set
WEP broadcast/unicast keys. This patch fixes connect failure
problem with AP using 802.1x-WEP.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of instantiating core info structs based upon the
chip identifier it is now done parsing information provided
on the device.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In brcmf_contstruct_reginfo() some error logging was added by:
commit f7c51a1a72f50870f80001ddf528a6f7f992bc16
Author: Arend van Spriel <arend@broadcom.com>
Date: Wed Dec 11 16:21:21 2013 +0100
brcmfmac: correct reporting HT40 support in wiphy htcap
This logging was not intended to be delivered and adds a lot
of messages in the log. The patch removes this logging statement.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_sdio_bus_sleep() function is called rather
frequently, which fills the log when TRACE level is enabled. Reduced
the level to SDIO.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch make several chip related functions host interface
independent by defining callback interface struct brcmf_buscore_ops.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the function sdio_remove will first destroy the datawork
workqueue and then detach the bus. This can create the situation
where work gets added on non-existing work queue resulting in panic.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmf_sdio_download_code_file is using a loop to send small blobs
of data. This is unnecessarily complex and was simplified with this
patch.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the function brcmf_sdiod_ramrw is supposed to be able to send
large blobs of data. However inside the loop the skb->len field
did not correctly get reset each round. As a result only small
blobs could be sent. This patch fixes this problem.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just renaming the file. This file will contain chip related functions
that are independent of the host interface type.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chip related functions will be made agnostic of the host
interface. However, some functions in the source file are
rather SDIO specific so better move it to the SDIO specific
source file.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Address of rte console was not initialized and so console logging
functionality didn't kick in. This patch fixes it and makes console
polling interval a debugfs variable.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To link module attribute with sdio device driver attribute in sysfs.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Expand the get_station command to also report dtim period and
beacon interval when the device is connected.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/main.c: In function ‘ath9k_has_tx_pending’:
drivers/net/wireless/ath/ath9k/main.c:1869: warning: ‘npend’ may be used uninitialized in this function
Introduced by commit 10e2318103 ("ath9k:
optimize ath9k_flush").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rtl8180/rtl8187 drivers, few register bit definitions have
names of form FOOBAR_SHIFT, suggesting they should be used as
shift offset, for example
reg |= (1 << ENABLE_FOO_SHIFT).
However they are actually defined as (1 << x) and thus they are
used (correctly) like
reg |= ENABLE_FOO_SHIFT;
This patch kills the misleading _SHIFT suffix.
Signed-off-by: andrea merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Fix IQ calibration" added a check
to ensure that valid i2_p_q2_a0_d1 values are not discarded.
But since it is masked with 0xfff earlier, the codepath
will not be executed.
The earlier case where all values above 0x800 were considered
invalid is incorrect, since the HW can return valid values
between 0x800 and 0xfff.
Cc: Kai Shi <kaishi@qca.qualcomm.com>
Reported-by: Alex Hacker <hacker@epn.ru>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Soon mac80211 will support multi-interface CSA so
using sc->csa_vif is not an option.
Instead just depend on vif->csa_active. Calling
ieee80211_csa_finish() multiple number of times
should not be an issue.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new HWSIM_ATTR_USE_CHANCTX attribute to the
HWSIM_CMD_CREATE_RADIO command to allow the creation of radios with
one channel that use channel contexts. If this attribute is not
present, the behaviour is the same as before (ie. single channel
radios don't use channel contexts and multi channel radios do).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's little point in setting the number of channels if the
entire combination struct is overwritten again later - that
was clearly intended the other way around, fix it.
Reported-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Orignal code will not detect a DMA mapping failure, causing the HW
to attempt a DMA from an invalid address.
This patch add the error check and eventually simply drops the TX
packet if we can't map it for DMA.
Signed-off-by: andrea merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In original code the old RX DMA buffer is unmapped and processed and at the end
of the isr a new buffer is mapped with pci_map_single and attached to the RX
descriptor.
If pci_map_single fails then the RX descriptor remains with no valid DMA buffer
attached.
In this condition the DMA will target where it shouldn't with obvious evil
consequences.
Simply avoiding re-arming the descriptor will prevent buggy DMA but it will
result soon in RX stuck.
This patch move the DMA mapping of the new buffer at the beginning of the ISR
(and it adds error check for pci_map_single success/fail).
If the DMA mapping fails then we do not unmap the old buffer and we re-arm the
descriptor without processing it, with the old DMA buffer still attached.
In this way we lose the currently RX-ed packet, but whenever next calls to
pci_map_single will succeed again,then the RX process will go on without stuck.
Signed-off-by: andrea merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of the PAPD group was increased in new devices.
Since we might now get empty entries on older devices, don't
warn if an entry is empty.
Signed-off-by: Ariej Marjieh <ariej.marjieh@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Alive notification ver2 support error table information
for 2 CPUs.
This is useful to fetch the error information in case of
firmware assert.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The 8000 family includes devices that don't support 11ac.
Add an iwl_cfg structure for them.
Signed-off-by: Ariej Marjieh <ariej.marjieh@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Newer NIC have different memory layout in their SRAM,
so change the checks in iwl_mvm_dump_nic_error_log
accordingly.
Signed-off-by: Ariej Marjieh <ariej.marjieh@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For TSF master/slave synchronization, the FW does not require
exact match in the beacon interval between the master interface
and the slave one, but instead requires that the beacon interval
of one interface is the module of the other.
Modify the tsf_id selection to align with the above.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The d3/d0i3 fw code requires the sta_id to be 0
(this is used to determine the rates and keys
to use in arp offloading).
Reserve sta_id 0 to station interface in order
to comply with this requirement.
Change some functions prototypes in order to
make the allocation function know about
the interface type.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The current WARNING isn't very helpful.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ieee80211_rx_status.flags is full. Define a new vht_flag
variable to be able to set more VHT related flags and make
room in flags.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath10k]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The purpose of this housekeeping is to make some room for
VHT flags. The radiotap vendor fields weren't in use.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When receiving an IBSS_JOINED event select the BSS object
based on the {bssid, channel} couple rather than the bssid
only.
With the current approach if another cell having the same
BSSID (but using a different channel) exists then cfg80211
picks up the wrong BSS object.
The result is a mismatching channel configuration between
cfg80211 and the driver, that can lead to any sort of
problem.
The issue can be triggered by having an IBSS sitting on
given channel and then asking the driver to create a new
cell using the same BSSID but with a different frequency.
By passing the channel to cfg80211_get_bss() we can solve
this ambiguity and retrieve/create the correct BSS object.
All the users of cfg80211_ibss_joined() have been changed
accordingly.
Moreover WARN when cfg80211_ibss_joined() gets a NULL
channel as argument and remove a bogus call of the same
function in ath6kl (it does not make sense to call
cfg80211_ibss_joined() with a zero BSSID on ibss-leave).
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Cc: libertas-dev@lists.infradead.org
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[minor code cleanup in ath6kl]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The scheduled scan matchsets were intended to be a list of filters,
with the found BSS having to pass at least one of them to be passed
to the host. When the RSSI attribute was added, however, this was
broken and currently wpa_supplicant adds that attribute in its own
matchset; however, it doesn't intend that to mean that anything
that passes the RSSI filter should be passed to the host, instead
it wants it to mean that everything needs to also have higher RSSI.
This is semantically problematic because we have a list of filters
like [ SSID1, SSID2, SSID3, RSSI ] with no real indication which
one should be OR'ed and which one AND'ed.
To fix this, move the RSSI filter attribute into each matchset. As
we need to stay backward compatible, treat a matchset with only the
RSSI attribute as a "default RSSI filter" for all other matchsets,
but only if there are other matchsets (an RSSI-only matchset by
itself is still desirable.)
To make driver implementation easier, keep a global min_rssi_thold
for the entire request as well. The only affected driver is ath6kl.
I found this when I looked into the code after Raja Mani submitted
a patch fixing the n_match_sets calculation to disregard the RSSI,
but that patch didn't address the semantic issue.
Reported-by: Raja Mani <rmani@qti.qualcomm.com>
Acked-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few places weren't checking that the frame passed to the
function actually has enough data even though the function
clearly documents it must have a payload byte. Make this
safer by changing the function to take an skb and checking
the length inside. The old version is preserved for now as
the rtl* drivers use it and don't have a correct skb.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Advertise to mac80211 that we can do channel switch both
for STA and AP/GO.
After each beacon transmission check if CSA is done and
call ieee80211_csa_finish if needed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When creating new devices, allow P2P-Device support to be
turned off to be able to test default behaviour with and
without the support.
Also add a module parameter for the default setting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's not a single rate control algorithm actually in
a separate module where the module refcount would be
required. Similarly, there's no specific rate control
module.
Therefore, all the module handling code in rate control
is really just dead code, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the code to allow making all the rate control ops
const, nothing ever needs to change them. Also change all
drivers to make use of this and mark the ops const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This required liberally sprinkling 'const' over brcmfmac
and mwifiex but seems like a useful thing to do since the
pointer can't really be written.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Addition of the frequency hints showed up couple of places in cfg80211
where pointers could be marked const and a shared function could be used
to fetch a valid channel.
Signed-off-by: Jouni Malinen <j@w1.fi>
[fix mwifiex]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The commit, "ath9k_hw: Fix incorrect Tx control power in AR9003 template"
fixed the incorrect values in the eeprom templates, but if
boards have already been calibrated with incorrect values,
they would still be using the wrong TX power. Fix this by assigning
a default value in such cases.
Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even though we make sure PowerSave is not enabled by default
by disabling the flag, WIPHY_FLAG_PS_ON_BY_DEFAULT on init,
PS could be enabled by userspace based on various factors
like battery usage etc. Since PS in ath9k is just broken
and has been untested for years, remove support for it, but
allow a user to explicitly enable it using a module parameter.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 ->sta_rc_update() callback must be atomic. Since we have to
take mutex and do other operations that can sleep when sending fimrware
commands to device, the only option to satisfy atomicity requirement of
->sta_rc_update(), that I can see, is introduce work_struct and defer
uploading new rates to that work.
Tested-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Raw id and FW id should be switched.
Tested-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is a copy/paste of patch provided by Sujith for ath9k.
"Even though we make sure PowerSave is not enabled by default
by disabling the flag, WIPHY_FLAG_PS_ON_BY_DEFAULT on init,
PS could be enabled by userspace based on various factors
like battery usage etc. Since PS in ath9k is just broken
and has been untested for years, remove support for it, but
allow a user to explicitly enable it using a module parameter."
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is know that PS cause issues on that old devices, disable it by
default.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have disabled it currently on other buses. PS can cause some issues,
not necessarily with our driver but on AP, that are not easy to debug.
Since behaviour differs on rt2800usb and rt2800pci, user usually blame
for malfunction rt2800usb driver, whereas issue is on AP side.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sta_rc_update() callback must be atomic, hence we can not take mutexes
or do other operations, which can sleep in ath9k_htc_sta_rc_update().
I think we can just return from ath9k_htc_sta_rc_update(), if it is
called without IEEE80211_RC_SUPP_RATES_CHANGED bit. That will help
with scheduling while atomic bug for most cases (except mesh and IBSS
modes).
For mesh and IBSS I do not see other solution like creating additional
workqueue, because sending firmware command require us to sleep, but
this can be done in additional patch.
Patch partially fixes bug:
https://bugzilla.redhat.com/show_bug.cgi?id=990955
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Aids in understanding excactly what a firmware is
offering.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The main complexity of the power code is that it needs to
take into account the firmware limitations.
These limitations state that we need to have a global
picture of the vifs present in the system to be able to
decide if we can enable power management on a specific vif.
Even device power save (as opposed to vif power management)
must be disabled in certain circumstances (monitor vif).
Refactor the current code to make this clearer by defining
a function that explicitely computes these constraints.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the driver detects old firmware, we disable support for
power management.
This greatly simplifies the code.
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of re-building the power command upon debugfs read,
store the latest command sent to the firmware.
This reduces the code complexity by reducing the number of
entries in the power code.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware doesn't allow per-vif beacon filtering: we can
use beacon filtering for one vif only. So remember which
vif has beacon filtering enabled in the iterator, and send
the command outside the iterator.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reduce indentation where it is possible.
Make a function static - it wasn't used outside its file
anyway.
Remove the unneeded pm_prevent state.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remove the enum abuse (using an enum to store a set of values),
the unneeded ret variable and unnecessary if nesting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The Sync to SCO is a feature that allows to synchronize
between the WiFi traffic and the expectable BT traffic
when SCO profile is active.
We need to set the validity bit in the command in the init
flow, and set / clear the enablement bit if we want to
enabled / disable the feature.
While at it, clean up the flags that are not used in the
API.
This feature needs to be enabled / disabled easily, so
export its enablement to constants.h.
Reviewed-by: Eyal Zolotov <eyal.zolotov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some older versions of wpa_supplicant don't necessarily stop
scheduled scan before starting a regular scan, and there's
nothing in the API that requires it either. As a consequence
our driver's behaviour of not allowing scan while scheduled
scan was in progress broke userspace.
However, it is valid to unilaterally stop scheduled scan at
any point in time, so when a regular scan request comes just
abort the scheduled scan and run the regular scan.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix a potential buffer overrun when creating the fw name
in drv->firmware_name by setting a maximal length to the
char array copied to it.
The maximal length is also updated to 32 rather than 25 to
keep both 32bit and 64bit alignment without requiring
padding to the struct it is in.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Newer devices have two embedded CPUs, and the firwmare for
both of them is include in the .ucode file requested upon
enumeration.
An empty section with address=0xFFFFCCCC separates between
the sections intended for cpu1 and the sections intended
for cpu2.
Update the driver to parse the .ucode file with this format
and act accordingly.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In iwl_mvm_calc_rssi() some values are calculated but then
never used, remove the calculations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Support taking an mvm ref (and preventing D0i3) by
writing '1' into the d0i3_refs debugfs file.
The reference can be unref by writing 0 to the same
file.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Schedule work to query the wakeup reasons, and
disconnect in some cases (e.g. beacon loss).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We need to ask the fw to wake up on incoming packets (that
pass the filters).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add d0i3_refs debugfs file that prints the currently taken
mvm D0i3 refs.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We don't want to go into D0i3, when P2P_CLI, AP (including
GO) or IBSS interfaces are running, so take appropriate
references.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Take a reference when ROC command is started, and
unref it on completion.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Take a reference when starting to scan and release it on completion.
Note that if the scan is cancelled/aborted, a completion will still be
sent up.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Hold a bitmap of taken references, according to the
reference reason (e.g. down, scan).
This will allow us validate our state and add some debugfs
entries later on.
Unref the transport when the FW is fully initialized,
allowing it to go into a low power mode.
Disallow the transition to low-power while recovery is in
progress.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Upon D0i3 entry/exit, iterate over the active interfaces
and configure them appropriately.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Configure skip-over-dtim and beacon filtering on D0i3
enter/exit.
Since the D0i3 entry/exit commands require different
command flags (e.g. CMD_HIGH_PRIORITY), add a new parameter
to the functions being called, and make the current users
pass CMD_SYNC.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the bus is in D0i3, we can't send regular commands to
the firmware. This means that we need to add a state to
remember what is our d0i3 state and make sure that only
d0i3 exit commands can be sent.
Add flags to CMD_ flags and transport status for this
purpose.
Commands with CMD_HIGH_PRIO set are queued at the head of
the command queue, behind other high priority commands.
Commands with CMD_SEND_IN_IDLE set can be sent while the
transport is idle (without taking rpm reference).
Commands with CMD_MAKE_TRANS_IDLE set indicate that command
completion should mark the transport as idle (and release
the bus).
Commands with CMD_WAKE_UP_TRANS set instruct the transport
to exit from idle when this command is completed.
The transport is marked as idle (STATUS_TRANS_IDLE) when
the FW enters D0i3 state. This bit is cleared when it
enters D0 state again.
Process only commands with CMD_SEND_IN_IDLE flag while the
transport is idle. Other enqueued commands will be
processed only later, right after exiting D0i3.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add new enter_d0i3 and exit_d0i3 ops that
will be called by the transport on D0i3 enter/exit.
Each one of these ops will include the host commands
mentionned in the previous patch.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
D0i3 is bus power saving feature. It involves the
firmware - the driver needs to send a list of commands
to the firmware before entering this state. Wake up from
d0i3 also requires a few commands to the firmware.
The trigger to enter D0i3 is an idle timeout that will be
implemented later and will most probably rely on RUNTIME_PM
infrastructure.
In order to prevent entrance to D0i3 in critical flows, we
implement here a reference infrastructure. When a ref is
taken, we can't enter D0i3.
PCIe does't support D0i3.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The tx backoff settings used by the thermal throttling mechanism can
also be used for enforcing a limit on the power consumption of the module.
Handle the platform PCIe power limitation by translating the limit
(measured in mw) to its respective tx backoff value. The translation is
module specific.
The resulting tx backoff value is sent to the ucode, and also serves as the
minimal backoff value that can be set by the thermal throttling mechanism.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some platforms may have power limitations on PCIe cards connected to
specific root ports.
This information is encoded as part of the ACPI tables, for instance:
<snip>
Name (SPLX, Package (0x02)
{
Zero,
Package (0x03)
{
0x07,
0x00000500,
0x80000000
}
})
Method (SPLC, 0, Serialized)
{
Return (SPLX)
}
</snip>
The structure returned contains the domain type, the default power
limitation and the default time window (reserved for future use).
Upon PCI probing, call the relevant ACPI method, parse the returned
structure, and save the power limitation.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Divide the maximal quota between all the data interfaces even in the
case of a single low latency binding without any other non low latency
interfaces, so that afterwards the quota allocation (which considers
the number of data interfaces) will be correct.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently the quota remainder was added to the first binding, although
it is possible that this was not a data binding (only the P2P_DEVICE
interface is part of the binding).
Fix this by adding the remainder to the first binding that was actually
allocated quota.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This makes the code a little bit longer as zero-extension
has to be done (mov vs. movzwl), but that's miniscule and
the space saving is significant, about 600 bytes in DVM
and 700 bytes in MVM, so the cache effect should be worth
the few bytes more code.
While at it, remove two spurious blank lines in variable
declaration blocks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This will be useful during tests done on the physical layer.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow reading and setting bcast filtering configuration
through debugfs.
By default, mvm->bcast_filters is used for setting
the bcast filtering configuration (these filters
will be configured for each associated station).
For testing purposes, allow overriding this configuration,
and setting the bcast filtering configuration manually.
The following debugfs keys can be used:
* bcast_filtering/override - use debugfs values instead
of default configuration
* bcast_filtering/filters - set filters (+ attributes)
* bcast_filtering/macs - per-mac bcast filtering
configuration (policy + attached filters)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add our ip as a new attribute to the bcast filtering
configuration (i.e. check the dest ip field of the
arp request).
Add bcast filter to pass incoming dhcp offer
broadcast frames as well (for sta vifs).
In order to support such dynamic configuration,
use the reserved1 field as a bitmap for driver internal
flags (which will indicate we want to configure the ip
in this attribute), and reconfigure the bcast
filtering on BSS_CHANGED_ARP_FILTER indication.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Configure arp request broadcast filter if this
option is enabled, in order to allow only arp
request broadcasts to pass-in.
(A following patch will make this filter even narrower
by limiting the arp request to our own ip)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Broadcast filtering allows dropping broadcast
frames that don't match the configured patterns.
Use predefined filters, and configure them for
each associated station vif.
There is no need to optimize and attach the same
filter to multiple vifs, as a following patch
will configure each filter to have per-vif unique
values.
Configure the bcast filtering on assoc changes.
Add a new IWLWIFI_BCAST_FILTERING Kconfig option
in order to enable broadcast filtering.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
As a debug tool, we dump the SRAM from the device when an
error occurs. The main users of this want it in a different
format, so change the format to suit their needs.
Also - add a short delay between the prints to make sure
that the user space logger can catch up.
This happens only when the firmware asserts, and only when
fw_restart is set to 0 which is typically a testing
configuration.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Based on the Bluetooth activity grading, we can stop using
the shared antenna and ask the stations to honor the new
SMPS state.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If a vif is in low latency mode, it should be in primary
channel.
Also tell BT Coex about the change when a vif enters or
exits low latency mode.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Limit the scheduling duration of bindings without a low-latency
interface in the firmware, this prevents those bindings from
occupying the medium for a period of time longer than what we
want for the other interfaces in low-latency mode.
As older firmware doesn't do anything with the max_duration field
and ignores it completely, there's no need for a firmware flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If there is/are interface(s) in low-latency mode, reserve a
percentage (currently 64%) of the quota for that binding to
improve the quality of service for those interfaces. However,
if there's more than one binding that has low-latency, then
give up and don't reserve, we can't allocate more than 100%.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
While an interface is in low-latency mode, for now powersave
should be disabled for it, so take low-latency into account
in the powersave code and force powersave recalculation when
low-latency mode changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For various traffic use cases, we want to be able to treat multi-
channel scenarios differently. Introduce a low-latency framework
that currently only has a debugfs file to enable low-latency mode,
but can later be extended.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Notify scan completed if fw_restart flow isn't going to be run.
Otherwise, the scan will stay stack forever and mac80211 will
not be able to remove the interface.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Don't stop scheduled scan before reporting HW restart;
mac80211 was changed to reschedule it after reconfigure.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In iwl_pcie_int_cause_non_ict, trans_pcie is used for lockdep
purposes only. Since this might not be enabled, trans_pcie
finds itself without user leading to a complaint from gcc.
Avoid using trans_pcie by inlining IWL_TRANS_GET_PCIE_TRANS.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since we use IWL_MVM_STATION_COUNT all over the driver, we
need to make sure that it is the right constant to look at.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We somtimes need to fetch the iwl_mvm_sta structure from a
station index - provide a helper to do that.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwlwifi-7260-8.ucode has been release. Warn if it is not
on the file system.
iwlwifi-7260-7.ucode is still supported for another kernel
version.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The code seems fine, as buf won't be assigned when an error
is returned, but checking for the error first is easier to
understand.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Also handle the bypass mode in which the second CPU doesn't
interfere.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This configuration is invalid for this family.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This register is not present in 8000 family devices.
There is prph register instead.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
APMG HW block was removed in this NIC, hence, no need to
configure it.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The identification of the hardware section in the NVM
of new devices has been changed, hence the need to add it
to iwl_cfg and adapt the code that uses this value
accordingly.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Newer firmware will support uAPSD clients in AP/GO mode, so complete
the driver support for it. The way it works is described in comments
in the code, but basically the driver just has to pass down all the
mac80211 requests and do accounting on agg/non-agg queues properly.
For older firmware, this doesn't change anything as it ignores the
fields used by the new firmware, and we only advertise uAPSD support
when the firmware does.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver wasn't reading the NVM properly. While this
didn't lead to any issue until now, it seems that there
is an old version of the NVM in the wild.
In this version, the A band channels appear to be valid
but the SKU capabilities (another field of the NVM) says
that A band isn't supported at all.
With this specific version of the NVM, the driver would
think that A band is supported while the HW / firmware
don't. This leads to asserts.
Cc: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Not doing so will let BT kill our probe requests leading to
failures in scan.
Cc: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We had a bug that prevented us from removing a station
after we entered the drain flow:
We assign sta to be NULL if it was an error value.
Then we tested it against -EBUSY, but forget to retrieve
the value again from mvm->fw_id_to_mac_id[sta_id].
Due to this bug, we ended up never removing the STA from
the firmware. This led to an firmware assert when we remove
the GO vif.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Configure scheduled scan to notify match found on every beacon
or probe response if the scan request doesn't contain valid ssid
list for filtering.
Without this configuration the FW passes all beacons to the host
but doesn't notify the stack that the scan results are ready for
processing.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This can be useful to be able to spot the firmware version
from the error reports without needing to fetch it from
another place.
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The iwlwifi scheduled scan implementation doesn't adhere to the
userspace API correctly - the API assumes that any new incoming
'incompatible' request (like scan or remain-on-channel for this
driver) will just cancel the scheduled scan. Instead our driver
relies on userspace cancelling it, thus breaking existing wpa_s
versions.
Cc: stable@vger.kernel.org [3.13]
Fixes: 35a000b7c1 ("iwlwifi: mvm: support sched scan if supported by the fw")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The address pointer used in the function shouldn't be static
since it's local data only. Having it static causes races if
a single machine has two devices, as the pointer would be
shared between instances.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ARP frames exchange does not work properly for UAPSD enabled AP.
ARP requests which arrives with access category 0 are processed
by network stack and send back with access category 0. FW changes
access category to 6. This is causing problems when UAPSD associated
STA is sleeping after has sent ARP request. Configure ARP access
category in FW to best effort (0) solves this problem. ARP frames
will be send with access category 0.
Simplify arp ac override functionality by removing redundant entry in
pdev param maping table. There should be only one entry in pdev param
map but enum has different name for different FW.
kvalo: change the warning message
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
Until now ath10k used a copy-by-value beacon
submission.
The new method passes a DMA address via WMI
command only. This command contains additional
metadata that fixes AP behaviour with regard
to powersave buffering.
This also fixes strange bug when multicast traffic
would freeze TX indefinitely.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Most channel switching logic has been implemented
already so this patch is pretty small. The patch
makes use of mac80211's vif->csa_active for AP CSA
handling.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Until now channel change wasn't propagating to FW
directly because operational channel is abstracted
by VDEVs and it wasn't really necessary since
ath10k implements hwscan and hwroc.
This effectively fixes STA CSA and allows for
future AP-like CSA as well.
kvalo: change error handling in ath10k_bss_info_changed()
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The threshold values for RX interrupt mitigation
are different for AR9003 and AR9002 families.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Process GTT interrupts" accidentally
had a line that was commented out.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the right function to update frequency value.
If rx skb is probe response or beacon, the wrong frequency value can
cause problem that bss info can't be updated when it should be.
Cc: <stable@vger.kernel.org>
Fixes: 8318d78a44 ("cfg80211 API for channels/bitrates, mac80211
and driver conversion")
Signed-off-by: ZHAO Gang <gamerh2o@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
8 bytes preamble
14 bytes src/dst/eth_type
6 bytes 0xff:0xff..
http://en.wikipedia.org/wiki/Wake-on-LAN#Magic_packethttp://en.wikipedia.org/wiki/EtherType
This will fail if we VLAN or the magic packet is encapsulated
as a UDP packet...
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
10.x FW has no structure member sw_version_1. Thus,
both fw_version_release and fw_version_build are not
available. The provided fw_version_major is also wrong.
Fix this by using the fw_version from struct wiphy.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k handles UAPSD completly in the firmware.
When works in AP mode we have to configure
UAPSD params for each station. Without this
patch we configure UAPSD params before we
send peer assoc command to the FW, which was
wrong. Next FW didn't know what should be trigger
frame, couse UAPSD didn't work correctly in AP mode.
To configure UAPSD params correctly we have to
send them after peer assoc command.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware has a feature to track if the associated STA is not acking the frames.
When that happens, the firmware sends WMI_PEER_STA_KICKOUT_EVENTID event to the
host. Enable that to faster detect when a STA has left BSS without sending a
deauth frame.
Also set huge keepalive timeouts to avoid using the keepalive functionality in
the firmware.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
None of the devices supported by iwldvm have support for
shadow registers. This means that we wake the NIC
when we increment the write pointer on Tx ring.
This happened even before my bad commit mentionned below.
Since my commit below, we wake up the NIC when we put a
host command on the ring regardless of shadow register
support. This means that in iwldvm (when the NIC doesn't
support shadow register), we wake up the NIC twice:
pcie_enqueue_hcmd:
wake up the NIC
iwl_pcie_txq_inc_wr_ptr:
wake up the NIC - no shadow reg support
Since waking up the NIC means that we need to acquire a
spinlock, this obviously leads to a recursive spinlock
and hence a freeze.
Fixes: b943949105 ("iwlwifi: pcie: keep the NIC awake when commands are in flight")
Reported-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable ap_ps_peer_param_cmdid for 10.x FW.
This is used mainly for AP UAPSD.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Reduce the Rx count threshold to make sure we read
the available credits for Tx.
Signed-off-by: Julien Massot <jmassot@aldebaran-robotics.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With the previous value (1700), some urb are dropped
with a babble error (urb status equal -EOVERFLOW).
These error seems to only happen when urb length is a
multiple of packet size (512).
Signed-off-by: Julien Massot <jmassot@aldebaran-robotics.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch will also change behavior of rx_beacons statistic.
Instead of collecting all received beacons, it will collect only
ours. This, IMO make more sense, since for troubleshooting we will
need to know count of our beacons, or both.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this function is used by most ath driver, so it can be moved here.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While registering the driver with cfg80211, update the threshold
value and retry limit to cfg80211.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bit 14 is actually reserved and bit 12 & 13 should be used for
11ac capability in fw_cap_info.
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes bug found by the kbuild test robot:
tree: git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next.git master
head: 1e2f9295f4
commit: 1cbbcb08c7 [135/140] wil6210: prefetch head of packet
config: make ARCH=microblaze allyesconfig
All error/warnings:
drivers/net/wireless/ath/wil6210/txrx.c: In function 'wil_vring_reap_rx':
>> drivers/net/wireless/ath/wil6210/txrx.c:381:2: error: implicit declaration of function 'prefetch' [-Werror=implicit-function-declaration]
prefetch(skb->data);
^
cc1: some warnings being treated as errors
vim +/prefetch +381 drivers/net/wireless/ath/wil6210/txrx.c
375 wil_err(wil, "Rx size too large: %d bytes!\n", dmalen);
376 kfree_skb(skb);
377 return NULL;
378 }
379 skb_trim(skb, dmalen);
380
> 381 prefetch(skb->data);
382
383 wil_hex_dump_txrx("Rx ", DUMP_PREFIX_OFFSET, 16, 1,
384 skb->data, skb_headlen(skb), false);
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevent a possible overflow condition which results in occasional
bad IQ coefficients and EVM numbers.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in the TX IQ calibration post
processing routine because of which the driver disables
TX IQ correction even though the calibration results
are valid. This fix is applicable for all chips in the
AR9003 family.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When removing the card the driver still tries to access registers
in the device. This patch adds another state for the bus that
indicates the device is no longer reachable. This avoids errors
accessing it while cleaning up the driver.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For scheduled scan results the driver does a escan to obtain BSS
details from the firmware. However, the escan uses a dynamically
determined function. This needs to be set appropriately when handling
scheduled scan results to avoid NULL pointer access.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rework function to allow only bcm4329 in case of chip backplane
type being sonics sillicon backplane.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware download code has been restructured so the reset vector
does not need to be stored in a structure, but keep it on the stack
to be passed to exit download function.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original core reset and disable routines do not work always
on running system. These routines were updated to properly reset
a core. When module is unloaded the device is put into download
state where all necessary cores have been reset. This will make
sure the device is in idle mode after module unload.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New bus layers like pcie require nvram parsing routines which are
the same routines as being used by sdio. Make these routines common
in the new file nvram.c. Update sdio to use these routines and
simplify the nvram upload process. Also add memory validation check
for downloaded firmware and nvram in debug mode.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Keeping this as 0 is ok according to spec section 9.7.11
as this means the limits are according to the Tx/Rx
supported MCS x NSS bitmap. Initially we've set these as
there were concerns of interop issues but these turned out
to be false.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If we try to write NVM that do not exist, the function will return
uninitialized value. fixed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add an inline helper function for getting an RX packet's
length or payload length and use it throughout the code
(most of which I did using an spatch.)
While at it, adjust some code, and remove a bogus comment
from the dvm calibration code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All beamformee supporting chips have the ability to support
VHT NDP in up to 4 STSs. So change the published beamformee
STS cap accordingly to 3 as it should be Nsts-1.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The request of SMPS issued by the Thermal Throttling code
was not reset when we disassociated - fix that.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It's a bit strange to treat an array as a pointer, so use proper
array indexing instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the length isn't set it means we want all the SRAM.
Also - this is perfectly valid to partially dump starting
at offset 0.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Discovered by klocwork
Array 'iwl_rate_mcs' of size 15 may use index value(s) -1
* rs.c:2562: index = iwl_hwrate_to_plcp_idx(rate)
* rs.c:2562: Result of function call 'iwl_hwrate_to_plcp_idx(rate)' is '[-1,14]'
* rs.c:2565: Array 'iwl_rate_mcs' size is 15.
* rs.c:2565: Possible attempt to access element -1 of array 'iwl_rate_mcs'.
While at it stop using index = -1 and always use IWL_RATE_INVALID
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some NIC comes with more than the 4 NVM (non volative
memory) sections described in the nvm_to_read array.
These NICs usually get their NVM from an external file
fetched from userland during init.
We already parsed the file, but sent to the NIC only 4 NVM
sections whereas there could be more sections in the file.
Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since seq_number is incremented right after using
it, so printed seq_ctrl was actually the next
one to be used.
Fix it by incrementing the seq_number only later,
before saving it.
Additionally, use the IEEE80211_SEQ_TO_SN macro
in order to print the actual sequence number.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enabling the oscillator consumes slightly more power (100uA)
but allows to make sure that we exit from L1 on time.
Not doing so might lead to a PCIe specification violation
since we might wake up from L1 at the wrong time.
This issue has been identified on 3160 and 7260 only.
On older NICs L1 off is not enabled, on newer NICs (7265),
the issue is fixed.
When the bug occurs the user sees that the NIC has
disappeared from the PCI bridge, any access to the device
returns 0xff.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=64541
and has been extensively discussed here:
http://markmail.org/thread/mfmpzqt3r333n4bo
Cc: stable@vger.kernel.org [3.10+]
Fixes: 99cd471423 ("iwlwifi: add 7000 series device configuration")
Reported-and-tested-by: wzyboy <wzyboy@wzyboy.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The call to clamp_t() first truncates the variable signed 8 bit and as a
result, the actual clamp is a no-op.
Fixes: 0d78156eef ('p54: improve site survey')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete a variable that is at most only assigned to a constant, but never
used otherwise.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
identifier i;
constant c;
@@
-T i;
<... when != i
-i = c;
...>
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Global Transmission Timeout interrupts are generated by
the HW when transmission of a frame fails - this is done
based on the threshold programmed in the AR_GTXTO register.
Currently, even though the interrupt is enabled for all chips,
it is not handled in the driver. This patch handles GTT events
for AR9003 and above chips, checking if the MAC/BB has hung
after successive GTT interrupts crosses a threshold (5).
This can be enabled for the older chips in the AR9002 family once
appropriate HW hang checks are implemented for them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to do this and we can avoid
an unused variable warning when CONFIG_ATH9K_WOW is
not selected.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This would be useful when debugging RX performance issues.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, rename node_stat to node_aggr.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
To be able to access the completion structure at teardown, it had to be moved
into the b43_wldev structure.
This patch also fixes a typo in a comment.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In https://bugzilla.kernel.org/show_bug.cgi?id=67561, a locking dependency is reported
when b43 is used with hostapd, and rfkill is used to kill the radio output.
The lockdep splat (in part) is as follows:
======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0 #1 Not tainted
-------------------------------------------------------
rfkill/10040 is trying to acquire lock:
(rtnl_mutex){+.+.+.}, at: [<ffffffff8146f282>] rtnl_lock+0x12/0x20
but task is already holding lock:
(rfkill_global_mutex){+.+.+.}, at: [<ffffffffa04832ca>] rfkill_fop_write+0x6a/0x170 [rfkill]
--snip--
Chain exists of:
rtnl_mutex --> misc_mtx --> rfkill_global_mutex
The fix is to move the initialization of the hardware random number generator
outside the code range covered by the rtnl_mutex.
Reported-by: yury <urykhy@gmail.com>
Tested-by: yury <urykhy@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is u64 data received from firmware. Little endian to cpu
conversion is required here.
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vladimir Kondratiev