A new Micron drive was just announced, once again recycling the first
part of the model string. Add an underscore to the M510/M550 pattern to
avoid picking up the new DC drive.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
I have a ST4000DM000 disk. If Linux is booted while the disk is spun down,
the command that sets transfer mode causes the disk to spin up. The
spin-up takes longer than the default 5s timeout, so the command fails and
timeout is reported.
Fix this by increasing the timeout to 15s, which is enough for the disk to
spin up.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Since no longer limiting max_sectors to BLK_DEF_MAX_SECTORS (commit 34b48db66e),
data corruption may occur on ST380013AS drive configured on 82801JI (ICH10 Family)
SATA controller. This patch will allow the driver to limit max_sectors as before
# cat /sys/block/sdb/queue/max_sectors_kb
512
I was able to double the max_sectors_kb value up to 16384 on linux-4.2.0-rc2
before seeing corruption, but seems safer to use previous limit. Without this
patch max_sectors_kb will be 32767.
tj: Minor comment update.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # v3.19 and later
Fixes: 34b48db66e ("block: remove artifical max_hw_sectors cap")
This device loses blocks, often the partition table area, on trim.
Disable TRIM.
http://pcengines.ch/msata16a.htm
Signed-off-by: Arne Fitzenreiter <arne_f@ipfire.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Some devices lose data on TRIM whether queued or not. This patch adds
a horkage to disable TRIM.
tj: Collapsed unnecessary if() nesting.
Signed-off-by: Arne Fitzenreiter <arne_f@ipfire.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Enabling AA on HP 250GB SATA disk VB0250EAVER causes errors:
[ 3.788362] ata3.00: failed to enable AA (error_mask=0x1)
[ 3.789243] ata3.00: failed to enable AA (error_mask=0x1)
Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk.
tj: Collected FPDMA_AA entries and updated comment.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
This commit adds the necessary quirk to make the Marvell 4140 SATA PMP
work properly. This PMP doesn't like SRST on port number 4 (the host
port) so this commit marks this port as not supporting SRST.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Since commit a483dcbfa2 ("ARM: shmobile: lager: Remove legacy
board support"), R-Car Gen2 SoCs are only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds ACPI supports for AHCI platform driver, which uses _CLS
method to match the device.
The following is an example of ASL structure in DSDT for a SATA controller,
which contains _CLS package to be matched by the ahci_platform driver:
Device (AHC0) // AHCI Controller
{
Name(_HID, "AMDI0600")
Name (_CCA, 1)
Name (_CLS, Package (3)
{
0x01, // Base Class: Mass Storage
0x06, // Sub-Class: serial ATA
0x01, // Interface: AHCI
})
Name (_CRS, ResourceTemplate ()
{
Memory32Fixed (ReadWrite, 0xE0300000, 0x00010000)
Interrupt (ResourceConsumer, Level, ActiveHigh, Exclusive,,,) { 387 }
})
}
Also, since ATA driver should not require PCI support for ATA_ACPI,
this patch removes dependency in the driver/ata/Kconfig.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A relatively small setup of cleanups this time around, and similar to last time
the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0zof
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Kevin Hilman:
"A relatively small setup of cleanups this time around, and similar to
last time the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
ARM: fix EFM32 build breakage caused by cpu_resume_arm
ARM: 8389/1: Add cpu_resume_arm() for firmwares that resume in ARM state
ARM: v7 setup function should invalidate L1 cache
mach-omap2: Remove use of deprecated marco, PTR_RET in devices.c
ARM: OMAP2+: Remove calls to deprecacted marco,PTR_RET in the files,fb.c and pmu.c
ARM: OMAP2+: Constify irq_domain_ops
ARM: OMAP2+: use symbolic defines for console loglevels instead of numbers
ARM: at91: remove useless Makefile.boot
ARM: at91: remove at91rm9200_sdramc.h
ARM: at91: remove mach/at91_ramc.h and mach/at91rm9200_mc.h
ARM: at91/pm: use the atmel-mc syscon defines
pcmcia: at91_cf: Use syscon to configure the MC/smc
ARM: at91: declare the at91rm9200 memory controller as a syscon
mfd: syscon: Add Atmel MC (Memory Controller) registers definition
ARM: at91: drop sam9_smc.c
ata: at91: use syscon to configure the smc
ARM: ux500: delete static resource defines
ARM: ux500: rename ux500_map_io
ARM: ux500: look up PRCMU resource from DT
ARM: ux500: kill off L2CC static map
...
Pull libata updates from Tejun Heo:
- a number of libata core changes to better support NCQ TRIM.
- ahci now supports MSI-X in single IRQ mode to support a new
controller which doesn't implement MSI or INTX.
- ahci now supports edge-triggered IRQ mode to support a new controller
which for some odd reason did edge-triggered IRQ.
- the usual controller support additions and changes.
* 'for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (27 commits)
libata: Do not blacklist Micron M500DC
ata: ahci_mvebu: add suspend/resume support
ahci, msix: Fix build error for !PCI_MSI
ahci: Add support for Cavium's ThunderX host controller
ahci: Add generic MSI-X support for single interrupts to SATA PCI driver
libata: finally use __initconst in ata_parse_force_one()
drivers: ata: add support for Ceva sata host controller
devicetree:bindings: add devicetree bindings for ceva ahci
ahci: added support for Freescale AHCI sata
ahci: Store irq number in struct ahci_host_priv
ahci: Move interrupt enablement code to a separate function
Doc: libata: Fix spelling typo found in libata.xml
ata:sata_nv - Change 1 to true for bool type variable.
ata: add Broadcom AHCI SATA3 driver for STB chips
Documentation: devicetree: add Broadcom SATA binding
libata: Fix regression when the NCQ Send and Receive log page is absent
ata: hpt366: fix constant cast warning
ata: ahci_xgene: potential NULL dereference in probe
ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.
libahci: Add support to handle HOST_IRQ_STAT as edge trigger latch.
...
Queued TRIM got disabled on Micron M500DC drives thanks to the
"Micron_M500*" pattern we had in place to accommodate the previous
generation of this drive family. Tweak the blacklist entry slightly so
we only disable queued TRIM for the non-DC variants of M500 drives.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
This commit adds suspend/resume support to the ahci_mvebu driver. The
suspend hook doesn't do anything special despite calling the generic
ahci_platform_suspend_host() function. However, the resume hook has to
restore the MBus windows configuration, as well as the regret option.
Tested on Marvell Armada 388 GP.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
It turned out the irq vector of the msix can be obtained from struct
msix_entry. This makes the lookup function for msi_desc obsolete.
This fixes a build error if PCI_MSI is unset:
drivers/ata/ahci.c: In function ‘msix_get_desc’:
drivers/ata/ahci.c:1210:2: error: ‘struct pci_dev’ has no member named ‘msi_list’
Catched by Fengguang's build bot.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds support for Cavium's ThunderX host controller. The
controller resides on the SoC and is a AHCI compatible SATA controller
with one port, compliant with Serial ATA 3.1 and AHCI Revision 1.31.
There can exists multiple SATA controllers on the SoC.
The controller depends on MSI-X support since the PCI ECAM controller
on the SoC does not implement MSI nor lagacy intx interrupt support.
Thus, during device initialization, if MSI fails MSI-X will be used to
enable the device's interrupts.
The controller uses non-standard BAR0 for its register range. The
already existing device lookup (vendor and device id) that is already
implemented for other host controllers is used to change the PCI BAR.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds generic MSI-X support for single interrupts to the
SATA PCI driver. MSI-X support is needed for host controller that only
have MSI-X support implemented, but no MSI or intx. This patch only
adds support for single interrupts, multiple per-port MSI-X interrupts
are not yet implemented.
The new implementation still initializes MSIs first. Only if that
fails, the code tries to enable MSI-X. If that fails too, setup is
continued with intx interrupts.
To not break other chips by this generic code change, there are the
following precautions:
* Interrupt ranges are not enabled at all.
* Only single interrupt mode is enabled for msix cap devices. Thus,
only one interrupt will be setup.
* During the discussion with Tejun we agreed to change the init
sequence from msix-msi-intx to msi-msix-intx. Thus, if a device
offers msi and init does not fail, the msix init code will not be
executed. This is equivalent to current code.
With this, the code only setups single mode msix as a last resort if
msi fails. No interrupt range is enabled at all. Only one interrupt
will be enabled.
tj: comment edits.
Changes of the patch series:
v5:
* updated patch subject that the patch only implements single IRQ
* moved Cavium specific code to a separate patch
* detect Cavium ThunderX device with PCI_CLASS_STORAGE_SATA_AHCI
instead of vendor/dev id
* added more comments to the code
* enable single msix support for all kind of devices (removing strict
check)
* rebased onto update libata/for-4.2 with patch 1, 2 applied
v4:
* removed implementation of ahci_init_intx()
* improved patch descriptions
* rebased onto libata/for-4.2
v3:
* store irq number in struct ahci_host_priv
* change initialization order from msix-msi-intx to msi-msix-intx
* improve comments in ahci_init_msix()
* improve error message in ahci_init_msix()
* do not enable MSI-X if MSI is actively disabled for the device
v2:
* determine irq vector from pci_dev->msi_list
Based on a patch from Sunil Goutham <sgoutham@cavium.com>.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Just six days after this FIXME was added seven years ago, Sam Ravnborg
added the missing feature (37c514e3df "Add missing init section
definitions"), though it ended up being called __initconst.
Let's use it; better late than never.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Adds support for Ceva sata host controller on Xilinx
Zynq UltraScale+ MPSoC.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Freescale introduced QorIQ series SOCs, like ls1021 ls2085, with AHCI
sata support. It complies with the serial ATA 3.0 specification
and the AHCI 1.3 specification.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Yuantian Tang <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata fixes from Tejun Heo:
"Two driver fixes. One is for an ahci_mvebu controller config bug and
the other fixes pata_octeon_cf build issue"
* 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
pata_octeon_cf: fix broken build
ata: ahci_mvebu: Fix wrongly set base address for the MBus window setting
MODULE_DEVICE_TABLE is referring to wrong driver's table and breaks the
build. Fix that.
Cc: stable@vger.kernel.org
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently, ahci supports only msi and intx. To also support msix the
handling of the irq number need to be changed. The irq number for msix
devices is taken from msi_list instead of pci_dev. Thus, the irq
number of a device needs to be stored in struct ahci_host_priv now.
This allows the host controller to be activated in a generic way.
This change is only intended for ahci drivers. For that reason the irq
number is stored in struct ahci_host_priv used only by ahci drivers.
Thus, the ABI changes only for ahci_host_activate(), but existing ata
drivers (about 50) are unaffected and keep unchanged. All users of
ahci_host_activate() have been updated.
While touching drivers/ata/libahci.c, doing a small code cleanup in
ahci_port_start().
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch refactors ahci_init_interrupts() and moves msi code to a
separate function. Need the split since we add msix initialization in
a later patch. The initialization for msix will be done after msi but
before intx.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fix a spelling typo found in libata.xml.
It is because libata.xml is generated from comments
in source, I have to fix it in libata-core.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
According to the Armada 38x datasheet, the window base address
registers value is set in bits [31:4] of the register and corresponds
to the transaction address bits [47:20].
Therefore, the 32bit base address value should be shifted right by
20bits and left by 4bits, resulting in 16 bit shift right.
The bug as not been noticed yet because if the memory available on
the platform is less than 2GB, then the base address is zero.
[gregory.clement@free-electrons.com: add extra-explanation]
Fixes: a3464ed2f1 (ata: ahci_mvebu: new driver for Marvell Armada 380
AHCI interfaces)
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Omri Itach <omrii@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
The variable swncq_enabled is bool type. Hence initialize it
with true instead of 1.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pretty straightforward driver, using the nice library-ization of the
generic ahci_platform driver.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 5d3abf8ff6 ("libata: Fall back to unqueued READ LOG EXT if
the DMA variant fails") allowed us to fall back to the unqueued READ
LOG variant if the queued version failed. However, if the device did
not support the page at all we would end up looping due to a merge
snafu.
Ensure we only take the fallback path once.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
gcc-5.x warns about a preexisting problem in the hpt36x pata driver:
drivers/ata/pata_hpt366.c: In function 'hpt36x_init_one':
drivers/ata/pata_hpt366.c:376:9: warning: assignment discards 'const' qualifier from pointer target type [-Wdiscarded-array-qualifiers]
Other ata drivers have the same problem, as ata_pci_bmdma_init_one
takes a non-const pointer, and they solve it by using a cast to
turn that pointer into a normal non-const pointer.
I also tried to change the ata core code to make host->private_data
a const pointer, but that quickly got out of hand, as some other
drivers expect it to be writable, so I ended up using the same
hack as the others here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use syscon/regmap to configure the smc. This allows to avoid using
at91sam9_smc.h and to compile the driver in a multiplatform configuration.
The driver will still not probe until the proper DT bindings are added. That
binding will include an atmel,smc property that is a phandle to the SMC the CF
controller is connected to.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Smatch complains about this potential NULL dereference of "acpi_id".
Fixes: c9802a4be6 ('ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata fixes from Tejun Heo:
"Rather big for fixes pull.
- SCC controllers never lived to see the light of the day. Both
libata and ide drivers removed.
- In some configurations, link power management policy changes
sometimes cause delayed spurious PHY events which can develop into
noticeable failures. This has been reported several times over the
years. Gabriele's patches suppress PHY events for a while after
LPM policy changes which should help most of these failures without
causing too much problem for hotplug use cases.
- A few controller specific fixes"
[ Hmm. I don't think removing SSC support is really a "fix", but hey, it
removes a lot of lines of code. Which I like. So ... good riddance ]
* 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: avoton port-disable reset-quirk
ata: select DW_DMAC in case of SATA_DWC
libata: Blacklist queued TRIM on all Samsung 800-series
libata: Ignore spurious PHY event on LPM policy change
libata: Add helper to determine when PHY events should be ignored
ata: ahci_st: fixup layering violations / drvdata errors
Remove celleb-only SCC PATA drivers
This patch enables full AHCI feature support for APM X-Gene SoC SATA
host controller. The following errata's are removed:
1. 2a0bdff6b9 ("ahci-xgene: fix the dma state machine lockup for the
IDENTIFY DEVICE PIO mode command")
2. 09c32aaa36 ("ahci_xgene: Fix the dma state machine lockup for the
ATA_CMD_SMART PIO mode command")
3. 1540035da7 ("ahci_xgene: Implement the xgene_ahci_poll_reg_val to
support PMP")
4. a3a84bc7c8 ("ahci_xgene: Implement the workaround to support PMP
enumeration and discovery")
5. 1102407bb7 ("ahci_xgene: Fix the DMA state machine lockup for the
ATA_CMD_PACKET PIO mode command")
6. 72f79f9e35 ("ahci_xgene: Removing NCQ support from the APM X-Gene
SoC AHCI SATA Host Controller driver")
In addition, enable PMP support for APM X-Gene SoC and enable FBS
support for second generation APM X-Gene SoC.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds the support to handle HOST_IRQ_STAT as edge trigger
latch.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch refactors the ahci_single_irq_intr function and also rename
it to ahci_single_level_irq_intr as it handles a level triggered latch.
Signed-off-by: Suman tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Avoton AHCI occasionally sees drive probe timeouts at driver load time.
When this happens SCR_STATUS indicates device detected, but no D2H FIS
reception. Reset the internal link state machines by bouncing
port-enable in the PCS register when this occurs.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since sata_dwc_460ex.c was moved to generic DMA driver we have to ensure that
user can still compile it.
Fixes: 8b3444852a (sata_dwc_460ex: move to generic DMA driver)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some devices advertise support for the READ/WRITE LOG DMA EXT commands
but fail when we try to issue them. This can lead to queued TRIM being
unintentionally disabled since the relevant feature flag is located in a
general purpose log page.
Fall back to unqueued READ LOG EXT if the DMA variant fails while
reading a log page.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Create a sysfs "trim" attribute for each ata_device that displays
whether DSM TRIM is "unsupported", "unqueued", "forced_unqueued"
(blacklisted) or "queued".
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
We have started seeing SSD firmware updates introduce support for queued
TRIM. Sadly, in most cases this support is completely untested and can
lead to either errors or data corruption.
Add two libata force flags that can be used to either enable or disable
queued TRIM support.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The queued TRIM problems appear to be generic to Samsung's firmware and
not tied to a particular model. A recent update to the 840 EVO firmware
introduced the same issue as we saw on 850 Pro.
Blacklist queued TRIM on all 800-series drives while we work this issue
with Samsung.
Reported-by: Günter Waller <g.wal@web.de>
Reported-by: Sven Köhler <sven.koehler@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When the LPM policy is set to ATA_LPM_MAX_POWER, the device might
generate a spurious PHY event that cuases errors on the link.
Ignore this event if it occured within 10s after the policy change.
The timeout was chosen observing that on a Dell XPS13 9333 these
spurious events can occur up to roughly 6s after the policy change.
Link: http://lkml.kernel.org/g/3352987.ugV1Ipy7Z5@xps13
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
This is a preparation commit that will allow to add other criteria
according to which PHY events should be dropped.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Brian noticed while working on another SATA driver that uses libahci_platform,
an error in this driver; it tries to the the driver data for its
device, while libata also thinks it can set the driver data. See:
ahci_platform_init_host()
-> ata_host_alloc_pinfo()
-> ata_host_alloc()
-> dev_set_drvdata()
So instead of sticking the IP-specific platform data into drvdata, let's
use the plat_data variable that is reserved for this use.
Addtionally plat_data isn't set until ahci_platform_init_host() has been
called further down in probe(). So re-work the st_ahci_probe_resets and
st_ahci_deassert_resets functions to take ahci_host_priv *hpriv as a
parameter.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Suggested-by: Brian Norris <computersforpeace@gmail.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was flashing
your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather than per
machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended transactions
on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree nodes, an
MSI erratum workaround, a couple minor performance improvements, config
updates, and misc fixes/cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=03Yh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan
Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was
flashing your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan
Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by
Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather
than per machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended
transactions on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree
nodes, an MSI erratum workaround, a couple minor performance
improvements, config updates, and misc fixes/cleanup.
* tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (196 commits)
powerpc/powermac: Fix build error seen with powermac smp builds
powerpc/pseries: Fix compile of memory hotplug without CONFIG_MEMORY_HOTREMOVE
powerpc: Remove PPC32 code from pseries specific find_and_init_phbs()
powerpc/cell: Fix iommu breakage caused by controller_ops change
powerpc/eeh: Fix crash in eeh_add_device_early() on Cell
powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTH
powerpc/perf/hv-24x7: Fail 24x7 initcall if create_events_from_catalog() fails
powerpc/pseries: Correct memory hotplug locking
powerpc: Fix missing L2 cache size in /sys/devices/system/cpu
powerpc: Add ppc64 hard lockup detector support
oprofile: Disable oprofile NMI timer on ppc64
powerpc/perf/hv-24x7: Add missing put_cpu_var()
powerpc/perf/hv-24x7: Break up single_24x7_request
powerpc/perf/hv-24x7: Define update_event_count()
powerpc/perf/hv-24x7: Whitespace cleanup
powerpc/perf/hv-24x7: Define add_event_to_24x7_request()
powerpc/perf/hv-24x7: Rename hv_24x7_event_update
powerpc/perf/hv-24x7: Move debug prints to separate function
powerpc/perf/hv-24x7: Drop event_24x7_request()
powerpc/perf/hv-24x7: Use pr_devel() to log message
...
Conflicts:
tools/testing/selftests/powerpc/Makefile
tools/testing/selftests/powerpc/tm/Makefile
- Generic PM domains support update including new PM domain
callbacks to handle device initialization better (Russell King,
Rafael J Wysocki, Kevin Hilman).
- Unified device properties API update including a new mechanism
for accessing data provided by platform initialization code
(Rafael J Wysocki, Adrian Hunter).
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano).
- intel_idle update including support for the Silvermont Core in
the Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause).
- New cpufreq driver for Hisilicon ACPU (Leo Yan).
- intel_pstate update including support for the Knights Landing
chip (Dasaratharaman Chandramouli, Kristen Carlson Accardi).
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann).
- powernv cpufreq driver update (Shilpasri G Bhat).
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi).
- powercap RAPL (Running-Average Power Limit) driver update
including support for Intel Broadwell server chips (Jacob Pan,
Mathias Krause).
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki).
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng).
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems
and a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede).
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu).
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki).
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu).
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu).
- Configurable delay for the system suspend/resume testing facility
(Brian Norris).
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=erd3
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups all over, although there are a few
items that sort of fall into the new feature category.
First off, we have new callbacks for PM domains that should help us to
handle some issues related to device initialization in a better way.
There also is some consolidation in the unified device properties API
area allowing us to use that inferface for accessing data coming from
platform initialization code in addition to firmware-provided data.
We have some new device/CPU IDs in a few drivers, support for new
chips and a new cpufreq driver too.
Specifics:
- Generic PM domains support update including new PM domain callbacks
to handle device initialization better (Russell King, Rafael J
Wysocki, Kevin Hilman)
- Unified device properties API update including a new mechanism for
accessing data provided by platform initialization code (Rafael J
Wysocki, Adrian Hunter)
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano)
- intel_idle update including support for the Silvermont Core in the
Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause)
- New cpufreq driver for Hisilicon ACPU (Leo Yan)
- intel_pstate update including support for the Knights Landing chip
(Dasaratharaman Chandramouli, Kristen Carlson Accardi)
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann)
- powernv cpufreq driver update (Shilpasri G Bhat)
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi)
- powercap RAPL (Running-Average Power Limit) driver update including
support for Intel Broadwell server chips (Jacob Pan, Mathias Krause)
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki)
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng)
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems and
a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede)
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu)
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki)
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu)
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu)
- Configurable delay for the system suspend/resume testing facility
(Brian Norris)
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
ACPI / scan: Fix NULL pointer dereference in acpi_companion_match()
ACPI / scan: Rework modalias creation when "compatible" is present
intel_idle: mark cpu id array as __initconst
powercap / RAPL: mark rapl_ids array as __initconst
powercap / RAPL: add ID for Broadwell server
intel_pstate: Knights Landing support
intel_pstate: remove MSR test
cpufreq: fix qoriq uniprocessor build
ACPI / scan: Take the PRP0001 position in the list of IDs into account
ACPI / scan: Simplify acpi_match_device()
ACPI / scan: Generalize of_compatible matching
device property: Introduce firmware node type for platform data
device property: Make it possible to use secondary firmware nodes
PM / watchdog: iTCO: stop watchdog during system suspend
cpufreq: hisilicon: add acpu driver
ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler
cpufreq: powernv: Report cpu frequency throttling
intel_idle: Add support for the Airmont Core in the Cherrytrail and Braswell SOCs
intel_idle: Update support for Silvermont Core in Baytrail SOC
PM / devfreq: tegra: Register governor on module init
...
The SCC PATA interface is only used by celleb.
celleb has been dropped [1], so drop the drivers.
[1] http://patchwork.ozlabs.org/patch/451730/
CC: "David S. Miller" <davem@davemloft.net>
CC: linux-ide@vger.kernel.org
CC: Valentin Rothberg <valentinrothberg@gmail.com>
CC: mpe@ellerman.id.au
CC: linuxppc-dev@lists.ozlab.org
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
- Hannes's patchset implements support for better error reporting
introduced by the new ATA command spec.
- the deperecated pci_ dma API usages have been replaced by dma_ ones.
- a bunch of hardware specific updates and some cleanups.
* 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: remove deprecated use of pci api
ahci: st: st_configure_oob must be called after IP is clocked.
ahci: st: Update the ahci_st DT documentation
ahci: st: Update the DT example for how to obtain the PHY.
sata_dwc_460ex: indent an if statement
libata: Add tracepoints
libata-eh: Set 'information' field for autosense
libata: Implement support for sense data reporting
libata: Implement NCQ autosense
libata: use status bit definitions in ata_dump_status()
ide,ata: Rename ATA_IDX to ATA_SENSE
libata: whitespace fixes in ata_to_sense_error()
libata: whitespace cleanup in ata_get_cmd_descript()
libata: use READ_LOG_DMA_EXT
libata: remove ATA_FLAG_LOWTAG
sata_dwc_460ex: re-use hsdev->dev instead of dwc_dev
sata_dwc_460ex: move to generic DMA driver
sata_dwc_460ex: join messages back
sata: xgene: add ACPI support for APM X-Gene SATA ports
ata: sata_mv: add proper definitions for LP_PHY_CTL register values
* pnp:
PNP: Avoid leaving unregistered device objects in lists
PNP: Convert pnp_lock into a mutex
PNP: tty/serial/8250/8250_fintek: Use module_pnp_driver to register driver
PNP: platform/x86/apple-gmux: Use module_pnp_driver to register driver
PNP: net/sb1000: Use module_pnp_driver to register driver
PNP: media/rc: Use module_pnp_driver to register driver
PNP: ide/ide-pnp: Use module_pnp_driver to register driver
PNP: ata/pata_isapnp: Use module_pnp_driver to register driver
PNP: tpm/tpm_infineon: Use module_pnp_driver to register driver
PNP: Add helper macro for pnp_register_driver boilerplate
PNP / ACPI: Use ACPI_COMPANION_SET() during initialization
Currently the ahci_st driver will hang the system on probe, as the
st_configure_oob function does some register writes before the IP
is clocked. This patch moves the function call to after
ahci_platform_enable_resources (which enables the IP clock), and
resolves the hang.
Addtionally st_ahci_configure_oob should be called in the st_ahci_resume
function, so we also rectify that ensuring it is also called after
the IP clock has been enabled.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
We shuffled some code around in 8b3444852a ('sata_dwc_460ex: move to
generic DMA driver') an accidentally deleted a tab character here. It
causes a Smatch warning "if statement not indented".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Blacklist queued TRIM on this drive for now.
Reported-by: Stefan Keller <linux-list@zahlenfresser.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
CC: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Micron has released an updated firmware (MU02) for M510/M550/MX100
drives to fix the issues with queued TRIM. Queued TRIM remains broken on
M500 but is working fine on later drives such as M600 and MX200.
Tweak our blacklist to reflect the above.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=71371
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Add some tracepoints for ata_qc_issue, ata_qc_complete, and
ata_eh_link_autopsy.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
If NCQ autosense or the sense data reporting feature is enabled
the LBA of the offending command should be stored in the sense
data 'information' field.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
ACS-4 defines a sense data reporting feature set.
This patch implements support for it.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some newer devices support NCQ autosense (cf ACS-4), so we should
be using it to retrieve the sense code and speed up recovery.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
If READ_LOG_DMA_EXT is supported we should try to use it for
reading the log pages.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
sata_sil24 for some reason pukes when tags are allocated round-robin
which helps tag ordered controllers. To work around the issue,
72dd299d50 ("libata: allow sata_sil24 to opt-out of tag ordered
submission") introduced ATA_FLAG_LOWTAG which tells libata tag
allocation to do lowest-first.
However, with the recent switch to blk-mq tag allocation, the liata
tag allocation code path is no longer used and the workaround is now
implemented in the block layer and selected by setting
scsi_host_template->tag_alloc_policy to BLK_TAG_ALLOC_FIFO. See
9269e23496 ("libata: make sata_sil24 use fifo tag allocator").
This leaves ATA_FLAG_LOWTAG withoout any actual user. Remove it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Shaohua Li <shli@fb.com>
Cc: Dan Williams <dan.j.williams@intel.com>
This patch re-uses hsdev->dev which is allocated on heap. Therefore, the
private structure, which is global variable, is reduced by one field.
In one case ap->dev is used and there it seems to be right decision.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The SATA implementation based on two actually different devices, i.e. SATA and
DMA controllers.
For Synopsys DesignWare DMA we have already a generic implementation of the
driver. Thus, the patch converts the code to use DMAEngine framework and
dw_dmac driver.
In future it will be better to split the devices inside DTS as well like it's
done on other platforms.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
It it better to have full message on one line. It simplifies to search for line
in the code by message when debugging.
Note that the lines which will be removed by sequential patch are not fixed
here.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ppc has special instruction forms to efficiently load and store values
in non-native endianness. These can be accessed via the arch-specific
{ld,st}_le{16,32}() inlines in arch/powerpc/include/asm/swab.h.
However, gcc is perfectly capable of generating the byte-reversing
load/store instructions when using the normal, generic cpu_to_le*() and
le*_to_cpu() functions eaning the arch-specific functions don't have much
point.
Worse the "le" in the names of the arch specific functions is now
misleading, because they always generate byte-reversing forms, but some
ppc machines can now run a little-endian kernel.
To start getting rid of the arch-specific forms, this patch removes them
from all the old Power Macintosh drivers, replacing them with the
generic byteswappers.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds ACPI support for the APM X-Gene SATA ports. When the system
boots using ACPI table, the SATA ports are able to configure using the
values supplied by the ACPI table rather than the DTS.
Signed-off-by: Feng Kan <fkan@apm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 9013d64e66 ("ata: sata_mv: fix disk hotplug for Armada
370/XP SoCs") added some manipulation of the LP_PHY_CTL register, but
using magic values. This commit changes the code to use proper
definitions for the LP_PHY_CTL register, which allows to document what
the different bits are doing.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
SAS controller has its own tag allocation, which doesn't directly match to ATA
tag, so SAS and SATA have different code path for ata tags. Originally we use
port->scsi_host (98bd4be1) to destinguish SAS controller, but libsas set
->scsi_host too, so we can't use it for the destinguish, we add a new flag for
this purpose.
Without this patch, the following oops can happen because scsi-mq uses
a host-wide tag map shared among all devices with some integer tag
values >= ATA_MAX_QUEUE. These unexpectedly high tag values cause
__ata_qc_from_tag() to return NULL, which is then dereferenced in
ata_qc_new_init().
BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
IP: [<ffffffff804fd46e>] ata_qc_new_init+0x3e/0x120
PGD 32adf0067 PUD 32adf1067 PMD 0
Oops: 0002 [#1] SMP DEBUG_PAGEALLOC
Modules linked in: iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi igb
i2c_algo_bit ptp pps_core pm80xx libsas scsi_transport_sas sg coretemp
eeprom w83795 i2c_i801
CPU: 4 PID: 1450 Comm: cydiskbench Not tainted 4.0.0-rc3 #1
Hardware name: Supermicro X8DTH-i/6/iF/6F/X8DTH, BIOS 2.1b 05/04/12
task: ffff8800ba86d500 ti: ffff88032a064000 task.ti: ffff88032a064000
RIP: 0010:[<ffffffff804fd46e>] [<ffffffff804fd46e>] ata_qc_new_init+0x3e/0x120
RSP: 0018:ffff88032a067858 EFLAGS: 00010046
RAX: 0000000000000000 RBX: ffff8800ba0d2230 RCX: 000000000000002a
RDX: ffffffff80505ae0 RSI: 0000000000000020 RDI: ffff8800ba0d2230
RBP: ffff88032a067868 R08: 0000000000000201 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8800ba0d0000
R13: ffff8800ba0d2230 R14: ffffffff80505ae0 R15: ffff8800ba0d0000
FS: 0000000041223950(0063) GS:ffff88033e480000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000058 CR3: 000000032a0a3000 CR4: 00000000000006e0
Stack:
ffff880329eee758 ffff880329eee758 ffff88032a0678a8 ffffffff80502dad
ffff8800ba167978 ffff880329eee758 ffff88032bf9c520 ffff8800ba167978
ffff88032bf9c520 ffff88032bf9a290 ffff88032a0678b8 ffffffff80506909
Call Trace:
[<ffffffff80502dad>] ata_scsi_translate+0x3d/0x1b0
[<ffffffff80506909>] ata_sas_queuecmd+0x149/0x2a0
[<ffffffffa0046650>] sas_queuecommand+0xa0/0x1f0 [libsas]
[<ffffffff804ea544>] scsi_dispatch_cmd+0xd4/0x1a0
[<ffffffff804eb50f>] scsi_queue_rq+0x66f/0x7f0
[<ffffffff803e5098>] __blk_mq_run_hw_queue+0x208/0x3f0
[<ffffffff803e54b8>] blk_mq_run_hw_queue+0x88/0xc0
[<ffffffff803e5c74>] blk_mq_insert_request+0xc4/0x130
[<ffffffff803e0b63>] blk_execute_rq_nowait+0x73/0x160
[<ffffffffa0023fca>] sg_common_write+0x3da/0x720 [sg]
[<ffffffffa0025100>] sg_new_write+0x250/0x360 [sg]
[<ffffffffa0025feb>] sg_write+0x13b/0x450 [sg]
[<ffffffff8032ec91>] vfs_write+0xd1/0x1b0
[<ffffffff8032ee54>] SyS_write+0x54/0xc0
[<ffffffff80689932>] system_call_fastpath+0x12/0x17
tj: updated description.
Fixes: 12cb5ce101 ("libata: use blk taging")
Reported-and-tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Removing some boilerplate by using module_pnp_driver instead of calling
register and unregister in the otherwise empty init/exit functions
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The OF functionality has moved to a common place and be used by many
archs. So we don't need to include the ppc arch specific header files
and depend on PPC_OF option any more. This is a preparation for
killing PPC_OF.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The driver was ignoring limits requested by libata.force. The output
would look like:
fsl-sata ffe18000.sata: Sata FSL Platform/CSB Driver init
ata1: FORCE: PHY spd limit set to 1.5Gbps
ata1: SATA max UDMA/133 irq 74
ata1: Signature Update detected @ 0 msecs
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 310)
Signed-off-by: Martin Hicks <mort@bork.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull block driver changes from Jens Axboe:
"This contains:
- The 4k/partition fixes for brd from Boaz/Matthew.
- A few xen front/back block fixes from David Vrabel and Roger Pau
Monne.
- Floppy changes from Takashi, cleaning the device file creation.
- Switching libata to use the new blk-mq tagging policy, removing
code (and a suboptimal implementation) from libata. This will
throw you a merge conflict, since a bug in the original libata
tagging code was fixed since this code was branched. Trivial.
From Shaohua.
- Conversion of loop to blk-mq, from Ming Lei.
- Cleanup of the io_schedule() handling in bsg from Peter Zijlstra.
He claims it improves on unreadable code, which will cost him a
beer.
- Maintainer update or NDB, now handled by Markus Pargmann.
- NVMe:
- Optimization from me that avoids a kmalloc/kfree per IO for
smaller (<= 8KB) IO. This cuts about 1% of high IOPS CPU
overhead.
- Removal of (now) dead RCU code, a relic from before NVMe was
converted to blk-mq"
* 'for-3.20/drivers' of git://git.kernel.dk/linux-block:
xen-blkback: default to X86_32 ABI on x86
xen-blkfront: fix accounting of reqs when migrating
xen-blkback,xen-blkfront: add myself as maintainer
block: Simplify bsg complete all
floppy: Avoid manual call of device_create_file()
NVMe: avoid kmalloc/kfree for smaller IO
MAINTAINERS: Update NBD maintainer
libata: make sata_sil24 use fifo tag allocator
libata: move sas ata tag allocation to libata-scsi.c
libata: use blk taging
NVMe: within nvme_free_queues(), delete RCU sychro/deferred free
null_blk: suppress invalid partition info
brd: Request from fdisk 4k alignment
brd: Fix all partitions BUGs
axonram: Fix bug in direct_access
loop: add blk-mq.h include
block: loop: don't handle REQ_FUA explicitly
block: loop: introduce lo_discard() and lo_req_flush()
block: loop: say goodby to bio
block: loop: improve performance via blk-mq
This is the usual grab bag of driver updates (hpsa, storvsc, mp2sas,
megaraid_sas, ses) plus an assortment of minor updates. There's also an
update to ufs which adds new phy drivers and finally a new logging
infrastructure for SCSI.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJU2Ty5AAoJEDeqqVYsXL0M9rAH/1xNpAxXuxQq+dW5Z+uOaX60
5RRIu7/xA1HEfzkT5FTHrolmogDjVqawu4PZS66iHDeo05RBVUlbTA8qCK+MlRcN
U6s0cLEw59eH3EaCfOGuYp/MnbhuV0eNxe0btmqJIQwuW3+gwZKGJdOq6LS2YasJ
k/DyIBVmkJAVsN56vm9q2vbtcZp+Bg+ngqBS+SC4TF7vV1WCtFmS6yaUf62PYW3D
+Irx37qHZntDR5wdw3dsuKDi5U8bl6myPjaVLnVJqg/WIF9RlCkjk5xpWT99AmVO
NmtYQxLLBlAQ5K+sIlBUwxZe+8q1l+Aj4TTmJHAfFtyfp25s7JR9I6/QtOyC5Kw=
=odol
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (hpsa, storvsc, mp2sas,
megaraid_sas, ses) plus an assortment of minor updates.
There's also an update to ufs which adds new phy drivers and finally a
new logging infrastructure for SCSI"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (114 commits)
scsi_logging: return void for dev_printk() functions
scsi: print single-character strings with seq_putc
scsi: merge consecutive seq_puts calls
scsi: replace seq_printf with seq_puts
aha152x: replace seq_printf with seq_puts
advansys: replace seq_printf with seq_puts
scsi: remove SPRINTF macro
sg: remove an unused variable
hpsa: Use local workqueues instead of system workqueues
hpsa: add in P840ar controller model name
hpsa: add in gen9 controller model names
hpsa: detect and report failures changing controller transport modes
hpsa: shorten the wait for the CISS doorbell mode change ack
hpsa: refactor duplicated scan completion code into a new routine
hpsa: move SG descriptor set-up out of hpsa_scatter_gather()
hpsa: do not use function pointers in fast path command submission
hpsa: print CDBs instead of kernel virtual addresses for uncommon errors
hpsa: do not use a void pointer for scsi_cmd field of struct CommandList
hpsa: return failed from device reset/abort handlers
hpsa: check for ctlr lockup after command allocation in main io path
...
Commit 84683a7e08 ("sata_dwc_460ex: enable COMPILE_TEST for the
driver") enabled this driver for non-ppc460-ex platforms, but it was
then disabled for ARM and ARM64 by commit 2de5a9c004 ("sata_dwc_460ex:
disable compilation on ARM and ARM64") because it's too noisy and
broken.
This disabled is entirely, because it's too noisy on x86-64 too, and
there's no point in disabling architectures one by one. At a minimum,
the code isn't 64-bit clean, and even on 32-bit it is questionable
whether it makes sense.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
09c32aaa36 ("ahci_xgene: Fix the dma state machine lockup for the
ATA_CMD_SMART PIO mode command.") missed 3.19 release. Fold it into
for-3.20.
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch addresses the issue with ATA_CMD_SMART pio mode command for
enumeration and device detection with ATA devices. The X-Gene AHCI
controller has an errata in which it cannot clear the BSY bit after
the PIO setup FIS. The dma state machine enters CMFatalErrorUpdate
state and locks up. It is the same issue as in the commit 2a0bdff6b9
("ahci-xgene: fix the dma state machine lockup for the IDENTIFY DEVICE
PIO mode command").
For example : without this patch it results in READ DMA command failure
as shown below :
[ 126.700072] ata2.00: exception Emask 0x0 SAct 0x0
SErr 0x0 action 0x6 frozen
[ 126.707089] ata2.00: failed command: READ DMA
[ 126.711426] ata2.00: cmd c8/00:08:00:55:57/00:00:00:00:00/e1 tag 1
dma 4096 in
[ 126.711426] res 40/00:ff:00:00:00/00:00:00:00:00/40 Emask
0x4 (timeout)
[ 126.725956] ata2.00: status: { DRDY }
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Reported-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
of_platform_device_create does not exist if OF_ADDRESS is not configured,
so limit its use accordingly.
Without this fix, the sparc64:allmodconfig build fails with
ERROR: "of_platform_device_create" [drivers/ata/libahci_platform.ko] undefined!
Fixes: c7d7ddee7e ("ata: libahci: Allow using multiple regulators")
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
The phy_power_off() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
The pci_dev_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
The owner module reference of the pata_of_platform's scsi_host is
initialized to pata_platform's one, because pata_of_platform driver
use a scsi_host_template defined in pata_platform. So this drivers
can be unloaded even if the scsi device is being accessed.
This fixes it by propagating the scsi_host_template to pata_of_platform
driver. The scsi_host_template is passed through a new
argument of __pata_platform_probe().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-ide@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
The owner module reference of the ahci platform's scsi_host is
initialized to libahci_platform's one, because these drivers use a
scsi_host_template defined in libahci_platform. So these drivers can
be unloaded even if the scsi device is being accessed.
This fixes it by pushing the scsi_host_template from libahci_platform
to all leaf drivers. The scsi_host_template is passed through a new
argument of ahci_platform_init_host().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-ide@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Function pdc_detect_pll_input_clock uses 'struct timeval'
to measure start and end times, used to compute the pll_clock value.
'struct timeval' on 32-bit systems will have its tv_sec field
overflow in year 2038 and beyond. This patch uses 'ktime_t'
(which uses 64 bits for seconds) for start and end times instead.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
libata starts using block tag now, we can use BLK_TAG_ALLOC_FIFO to
solve the sata_sil24 tag bug.
https://bugzilla.kernel.org/show_bug.cgi?id=87101
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Basically move the sas ata tag allocation to libata-scsi.c to make it clear
these staffs are just for sas.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
libata uses its own tag management which is duplication and the
implementation is poor. And if we switch to blk-mq, tag is build-in.
It's time to switch to generic taging.
The SAS driver has its own tag management, and looks we can't directly
map the host controler tag to SATA tag. So I just bypassed the SAS case.
I changed the code/variable name for the tag management of libata to
make it self contained. Only sas will use it. Later if libsas implements
its tag management, the tag management code in libata can be deleted
easily.
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit c7d7ddee7e ("ata: libahci: Allow using multiple regulators")
releases regulators during ahci_platform_put_resources(). That doesn't
work because the function is run as part of the devres machinery. Such
resources are torn down in reverse order. Since the array that holds
pointers to the regulators is allocated using devres after the device
context to which ahci_platform_put_resources() is attached, the memory
will be freed before calling ahci_platform_put_resources() and thereby
causing a use-after-free error.
This commit fixes this by using regular allocations for the array. The
memory can then be freed after the regulators have been released. This
conserves the advantages of using the managed API.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
We should only try to evaluate the cdb if this is an ATAPI
device, for any other device the 'cdb' field and the cdb_len
has no meaning.
Fixes: cbba5b0ee4
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tejun Heo <tj@kernel.org>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
It is possible for ata_sff_flush_pio_task() to set ap->hsm_task_state to
HSM_ST_IDLE in between the time __ata_sff_port_intr() checks for HSM_ST_IDLE
and before it calls ata_sff_hsm_move() causing ata_sff_hsm_move() to BUG().
This problem is hard to reproduce making this patch hard to verify, but this
fix will prevent the race.
I have not been able to reproduce the problem, but here is a crash dump from
a 2.6.32 kernel.
On examining the ata port's state, its hsm_task_state field has a value of HSM_ST_IDLE:
crash> struct ata_port.hsm_task_state ffff881c1121c000
hsm_task_state = 0
Normally, this should not be possible as ata_sff_hsm_move() was called from ata_sff_host_intr(),
which checks hsm_task_state and won't call ata_sff_hsm_move() if it has a HSM_ST_IDLE value.
PID: 11053 TASK: ffff8816e846cae0 CPU: 0 COMMAND: "sshd"
#0 [ffff88008ba03960] machine_kexec at ffffffff81038f3b
#1 [ffff88008ba039c0] crash_kexec at ffffffff810c5d92
#2 [ffff88008ba03a90] oops_end at ffffffff8152b510
#3 [ffff88008ba03ac0] die at ffffffff81010e0b
#4 [ffff88008ba03af0] do_trap at ffffffff8152ad74
#5 [ffff88008ba03b50] do_invalid_op at ffffffff8100cf95
#6 [ffff88008ba03bf0] invalid_op at ffffffff8100bf9b
[exception RIP: ata_sff_hsm_move+317]
RIP: ffffffff813a77ad RSP: ffff88008ba03ca0 RFLAGS: 00010097
RAX: 0000000000000000 RBX: ffff881c1121dc60 RCX: 0000000000000000
RDX: ffff881c1121dd10 RSI: ffff881c1121dc60 RDI: ffff881c1121c000
RBP: ffff88008ba03d00 R8: 0000000000000000 R9: 000000000000002e
R10: 000000000001003f R11: 000000000000009b R12: ffff881c1121c000
R13: 0000000000000000 R14: 0000000000000050 R15: ffff881c1121dd78
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffff88008ba03d08] ata_sff_host_intr at ffffffff813a7fbd
#8 [ffff88008ba03d38] ata_sff_interrupt at ffffffff813a821e
#9 [ffff88008ba03d78] handle_IRQ_event at ffffffff810e6ec0
--- <IRQ stack> ---
[exception RIP: pipe_poll+48]
RIP: ffffffff81192780 RSP: ffff880f26d459b8 RFLAGS: 00000246
RAX: 0000000000000000 RBX: ffff880f26d459c8 RCX: 0000000000000000
RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff881a0539fa80
RBP: ffffffff8100bb8e R8: ffff8803b23324a0 R9: 0000000000000000
R10: ffff880f26d45dd0 R11: 0000000000000008 R12: ffffffff8109b646
R13: ffff880f26d45948 R14: 0000000000000246 R15: 0000000000000246
ORIG_RAX: ffffffffffffff10 CS: 0010 SS: 0018
RIP: 00007f26017435c3 RSP: 00007fffe020c420 RFLAGS: 00000206
RAX: 0000000000000017 RBX: ffffffff8100b072 RCX: 00007fffe020c45c
RDX: 00007f2604a3f120 RSI: 00007f2604a3f140 RDI: 000000000000000d
RBP: 0000000000000000 R8: 00007fffe020e570 R9: 0101010101010101
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fffe020e5f0
R13: 00007fffe020e5f4 R14: 00007f26045f373c R15: 00007fffe020e5e0
ORIG_RAX: 0000000000000017 CS: 0033 SS: 002b
Somewhere between the ata_sff_hsm_move() check and the ata_sff_host_intr() check, the value changed.
On examining the other cpus to see what else was running, another cpu was running the error handler
routines:
PID: 326 TASK: ffff881c11014aa0 CPU: 1 COMMAND: "scsi_eh_1"
#0 [ffff88008ba27e90] crash_nmi_callback at ffffffff8102fee6
#1 [ffff88008ba27ea0] notifier_call_chain at ffffffff8152d515
#2 [ffff88008ba27ee0] atomic_notifier_call_chain at ffffffff8152d57a
#3 [ffff88008ba27ef0] notify_die at ffffffff810a154e
#4 [ffff88008ba27f20] do_nmi at ffffffff8152b1db
#5 [ffff88008ba27f50] nmi at ffffffff8152aaa0
[exception RIP: _spin_lock_irqsave+47]
RIP: ffffffff8152a1ff RSP: ffff881c11a73aa0 RFLAGS: 00000006
RAX: 0000000000000001 RBX: ffff881c1121deb8 RCX: 0000000000000000
RDX: 0000000000000246 RSI: 0000000000000020 RDI: ffff881c122612d8
RBP: ffff881c11a73aa0 R8: ffff881c17083800 R9: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff881c1121c000
R13: 000000000000001f R14: ffff881c1121dd50 R15: ffff881c1121dc60
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0000
--- <NMI exception stack> ---
#6 [ffff881c11a73aa0] _spin_lock_irqsave at ffffffff8152a1ff
#7 [ffff881c11a73aa8] ata_exec_internal_sg at ffffffff81396fb5
#8 [ffff881c11a73b58] ata_exec_internal at ffffffff81397109
#9 [ffff881c11a73bd8] atapi_eh_request_sense at ffffffff813a34eb
Before it tried to acquire a spinlock, ata_exec_internal_sg() called ata_sff_flush_pio_task().
This function will set ap->hsm_task_state to HSM_ST_IDLE, and has no locking around setting this
value. ata_sff_flush_pio_task() can then race with the interrupt handler and potentially set
HSM_ST_IDLE at a fatal moment, which will trigger a kernel BUG.
v2: Fixup comment in ata_sff_flush_pio_task()
tj: Further updated comment. Use ap->lock instead of shost lock and
use the [un]lock_irq variant instead of the irqsave/restore one.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
The current implementation of the libahci allows using multiple PHYs
but not multiple regulators. This patch adds the support of multiple
regulators. Until now it was mandatory to have a PHY under a subnode,
now a port subnode can contain either a regulator or a PHY (or both).
In order to be able to asociate a port with a regulator the port are
now a platform device in the device tree case.
There was only one driver which used directly the regulator field of
the ahci_host_priv structure. To preserve the bisectability the change
in the ahci_imx driver was done in the same patch.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The phy_ functions handle the NULL pointer case, so there is no need
to skip them if there is a NULL pointer. Moreover, after the error
label there is already no check on the pointer. This patch removes the
unnecessary tests and brings some consistency.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Ronny reports: https://bugzilla.kernel.org/show_bug.cgi?id=87101
"Since commit 8a4aeec8d "libata/ahci: accommodate tag ordered
controllers" the access to the harddisk on the first SATA-port is
failing on its first access. The access to the harddisk on the
second port is working normal.
When reverting the above commit, access to both harddisks is working
fine again."
Maintain tag ordered submission as the default, but allow sata_sil24 to
continue with the old behavior.
Cc: <stable@vger.kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Reported-by: Ronny Hegewald <Ronny.Hegewald@online.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In order to make it possible to restore from hibernation not only in Linux but
also in e.g. U-Boot, we have to extend sata_rcar_{suspend|resume}() to {freeze|
thaw}() PM methods and implement the restore() PM method.
Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
[Sergei: killed unused variable, changed the order of initializers, modified
copyrights, renamed, modified changelog.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Until the driver is corrected to stop using mach/at91isam9_smc.h, it won't
compile in a ARCH_MULTIPLATFORM configuration.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch removes a duplicate AHCI-mode SATA Device ID for the Intel Sunrise Point PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
For now disable the compilation of the driver on ARM and ARM64. In the future
we will fix the DMA handling in that driver and re-enable compilation back.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Remove the function ata_do_simple_cmd() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Tejun Heo <tj@kernel.org>
According to the Serial ATA AHCI specification, Device Sleep is an
optional feature and as such no errors should be printed if it's
missing. Keep informing users, but use dev_info() instead of dev_err().
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
libata already uses an internal buffer, so we should be using
__scsi_format_command() here.
Tested-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As defined, the DRAT (Deterministic Read After Trim) and RZAT (Return
Zero After Trim) flags in the ATA Command Set are unreliable in the
sense that they only define what happens if the device successfully
executed the DSM TRIM command. TRIM is only advisory, however, and the
device is free to silently ignore all or parts of the request.
In practice this renders the DRAT and RZAT flags completely useless and
because the results are unpredictable we decided to disable discard in
MD for 3.18 to avoid the risk of data corruption.
Hardware vendors in the real world obviously need better guarantees than
what the standards bodies provide. Unfortuntely those guarantees are
encoded in product requirements documents rather than somewhere we can
key off of them programatically. So we are compelled to disabling
discard_zeroes_data for all devices unless we explicitly have data to
support whitelisting them.
This patch whitelists SSDs from a few of the main vendors. None of the
whitelists are based on written guarantees. They are purely based on
empirical evidence collected from internal and external users that have
tested or qualified these drives in RAID deployments.
The whitelist is only meant as a starting point and is by no means
comprehensive:
- All intel SSD models except for 510
- Micron M5?0/M600
- Samsung SSDs
- Seagate SSDs
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The patch converts ->probe() to use devm_kzalloc that simplifies error path.
Note that ata_host_alloc_pinfo() has been using device resources already.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There is no need to print a message about failure of memory allocation. The
caller will get an error code and may print the same.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fixes the style of usage of a node pointer. There is no functional
change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There are a lot sparse warnings. Most of them related to __iomem keyword which
sometimes absent when it's needed and vise versa.
The patch fixes most of the warnings.
While at it, remove the redundant sata_dwc_sht.can_queue
initialization to ATA_DEF_QUEUE.
tj: Added description about ATA_DEF_QUEUE init removal.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
To test how the driver could be compiled in the non-native environment let's
enable COMPILE_TEST for it. It would be useful for further work.
This patch enables COMPILE_TEST for the driver and fixes compilation errors on
at least x86 platforms.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Driver core sets it to NULL upon probe failure or release.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull to receive 4aaa71873d ("sata_dwc_460ex: fix resource leak on
error path") so that further cleanup patches can be queued on top.
Signed-off-by: Tejun Heo <tj@kernel.org>
DMA mapped IO should be unmapped on the error path in probe() and
unconditionally on remove().
Fixes: 62936009f3 ([libata] Add 460EX on-chip SATA driver, sata_dwc_460ex)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Remove the FIXME comment in atapi_eh_request_sense () asking whether
memset of sense buffer is necessary. The buffer may be partially or
fully filled by the device. We want it to be cleared.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Due to H/W errata, the controller is unable to save the PMP
field fetched from command header before sending the H2D FIS.
When the device returns the PMP port field in the D2H FIS, there is
a mismatch and results in command completion failure. The workaround
is to write the pmp value to PxFBS.DEV field before issuing any command
to PMP.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch implements the function xgene_ahci_poll_reg_val
to poll PxCI for multiple IDENTIFY DEVICE commands to finish before
restarting the DMA engine.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull to receive the following two ahci_xgene fixes for the planned
xgene PMP support patches.
5c0b8e0de7 ("ahci_xgene: Fix the endianess issue in APM X-Gene SoC AHCI SATA controller driver.")
1102407bb7 ("ahci_xgene: Fix the DMA state machine lockup for the ATA_CMD_PACKET PIO mode command.")
Signed-off-by: Tejun Heo <tj@kernel.org>
The driver sata_dwc_460ex is using this symbol. To build it as a
module we have to have the symbol exported. This patch adds
EXPORT_SYMBOL_GPL() macro for that.
tj: Updated to use EXPORT_SYMBOL_GPL() instead of EXPORT_SYMBOL() as
the only known user is an in-tree driver. Suggested by Sergei.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
This patch addresses the issue with ATA_CMD_PACKET pio mode
command for enumeration and device detection with ATAPI devices.
The X-Gene AHCI controller has an errata in which it cannot clear
the BSY bit after the PIO setup FIS. The dma state machine enters
CMFatalErrorUpdate state and locks up.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fixes the big endian mode issue with function
xgene_ahci_read_id.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Changes the spelling typos of removeable to removable where
ata_id_removeable is defined in ata.h and called in libata-scsi.c
respectively.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so Kconfig options
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace PM_RUNTIME with PM in Kconfig dependencies throughout the
tree.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tejun Heo <tj@kernel.org>
Pull libata changes from Tejun Heo:
"The only interesting piece is the support for shingled drives. The
changes in libata layer are minimal. All it does is identifying the
new class of device and report upwards accordingly"
* 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: Remove FIXME comment in atapi_request_sense()
sata_rcar: Document deprecated "renesas,rcar-sata"
sata_rcar: Add clocks to sata_rcar bindings
ahci_sunxi: Make AHCI_HFLAG_NO_PMP flag configurable with a module option
libata-scsi: Update SATL for ZAC drives
libata: Implement ATA_DEV_ZAC
libsas: use ata_dev_classify()
This patch is the usual mix of driver updates (srp, ipr, scsi_debug, NCR5380,
fnic, 53c974, ses, wd719x, hpsa, megaraid_sas). Of those, wd7a9x is new and
53c974 is a rewrite of the old tmscsim driver and the extensive work by Finn
Thain rewrites all the NCR5380 based drivers. There's also extensive
infrastructure updates: a new logging infrastructure for sense information and
a rewrite of the tagged command queue API and an assortment of minor updates.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJUhgazAAoJEDeqqVYsXL0MxIYH/2wCs9sne5cfDTjfufLJDdu1
WLoJgNMxv+14OukknJfG2Kk1WlHgLRM5+TVWIGiG0mmjXuFyShzIqEOHKTDWqxnE
tBH4wLi/+XYqZAmAeim4/2zhvf+cUVVlIu01VERR5uwaBWYM8BeLSwjdnAAvEEwb
iV74p1WV6frXo4guADplgtkjD0YxI4MTUZ1figRMlLO6WLFFyQ+95UfY8jFs+eQv
zk63y7Mm7dQNd57/Wl3i89lw0kqlaJSZNl8Ovj1axy4rDYzT1wXhY8mEwD8fI8Ym
wahldjFE5vXgj0NpO3tB3Z+UDP2YmQduMyzTxkPNnrEPKiOCsnQo42XR6vb92cQ=
=Y+DU
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch is the usual mix of driver updates (srp, ipr, scsi_debug,
NCR5380, fnic, 53c974, ses, wd719x, hpsa, megaraid_sas).
Of those, wd7a9x is new and 53c974 is a rewrite of the old tmscsim
driver and the extensive work by Finn Thain rewrites all the NCR5380
based drivers.
There's also extensive infrastructure updates: a new logging
infrastructure for sense information and a rewrite of the tagged
command queue API and an assortment of minor updates"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (183 commits)
scsi: set fmt to NULL scsi_extd_sense_format() by default
libsas: remove task_collector mode
wd719x: remove dma_cache_sync call
scsi_debug: add Report supported opcodes+tmfs; Compare and write
scsi_debug: change SCSI command parser to table driven
scsi_debug: add Capacity Changed Unit Attention
scsi_debug: append inject error flags onto scsi_cmnd object
scsi_debug: pinpoint invalid field in sense data
wd719x: Add firmware documentation
wd719x: Introduce Western Digital WD7193/7197/7296 PCI SCSI card driver
eeprom-93cx6: Add (read-only) support for 8-bit mode
esas2r: fix an oversight in setting return value
esas2r: fix an error path in esas2r_ioctl_handler
esas2r: fir error handling in do_fm_api
scsi: add SPC-3 command definitions
scsi: rename SERVICE_ACTION_IN to SERVICE_ACTION_IN_16
scsi: remove scsi_driver owner field
scsi: move scsi_dispatch_cmd to scsi_lib.c
scsi: stop passing a gfp_mask argument down the command setup path
scsi: remove scsi_next_command
...
Conflicts:
drivers/scsi/scsi_debug.c
Agreed and tested resolution to a merge problem between a fix in scsi_debug
and a driver update
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Just like 0x1600 which got blacklisted by 66a7cbc303 ("ahci: disable
MSI instead of NCQ on Samsung pci-e SSDs on macbooks"), 0xa800 chokes
on NCQ commands if MSI is enabled. Disable MSI.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Dominik Mierzejewski <dominik@greysector.net>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=89171
Cc: stable@vger.kernel.org
Remove the FIXME comment in atapi_request_sense() asking whether
memset of sense buffer is necessary. The buffer may be partially or
fully filled by the device. We want it to be cleared.
tj: Updated description.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
irq_of_parse_and_map() returns 0 on error (the result is unsigned int),
so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
SPC-3 defines SERVICE ACTION IN(12) and SERVICE ACTION IN(16).
So rename SERVICE_ACTION_IN to SERVICE_ACTION_IN_16 to be
consistent with SPC and to allow for better distinction.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Tested-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
The use of the AHCI_HFLAG_NO_PMP flag is something which we inherited from
the Allwinner android kernel sources, and I've always wanted to test if this
is really necessary.
So recently I've bought a sata port multiplexer, and I've given this a test
spin on both A10 and A20 devices, and it seems to work fine:
[ 2.154456] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.161092] ata1.15: Port Multiplier 1.2, 0x197b:0x0325 r0, 5 ports, feat 0x5/0xf
[ 2.175511] ata1.00: hard resetting link
[ 2.524929] ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 2.531430] ata1.01: hard resetting link
[ 2.974465] ata1.01: link resume succeeded after 1 retries
[ 3.094932] ata1.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.101431] ata1.02: hard resetting link
[ 4.174466] ata1.02: failed to resume link (SControl 0)
[ 4.180065] ata1.02: SATA link down (SStatus 0 SControl 0)
(and the same for links 3 and 4)
Once the NO_PMP flag is removed it correctly sees the 2 disks which I've
attached, and I can mount and use them just fine.
Unfortunately when I then directly attached a disk to the sata port on the
sunxi SoC, and booted a kernel without the AHCI_HFLAG_NO_PMP flag, it would
not recognize that disk.
It turns out that the sata controller in the sunxi SoCs fails to handle
soft-resets issued to directly attached disks, and when pmp support is
enabled the kernel will always issue a soft-reset.
So add a module parameter to enable pmp usage, and default this to off, so
that directly attached disks keep working normally.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
ZAC (zoned-access command) drives translate into ZBC (Zoned block
command) device type for SCSI. So implement the correct mappings
into libata-scsi and update the SCSI command set versions.
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add new ATA device type for ZAC devices.
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Changes into the AHCI subsystem have introduced a bug by not taking into
account the force_port_map and mask_port_map parameters when using the
ahci_pci_save_initial_config function. This commit fixes it by setting
the internal parameters of the ahci_port_priv structure.
Fixes: 725c7b570f
Reported-and-tested-by: Zlatko Calusic <zcalusic@bitsync.net>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
This patch adds the AHCI-mode SATA Device IDs for the Intel Sunrise Point PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Samsung pci-e SSDs on macbooks failed miserably on NCQ commands, so
67809f85d3 ("ahci: disable NCQ on Samsung pci-e SSDs on macbooks")
disabled NCQ on them. It turns out that NCQ is fine as long as MSI is
not used, so let's turn off MSI and leave NCQ on.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=60731
Tested-by: <dorin@i51.org>
Tested-by: Imre Kaloz <kaloz@openwrt.org>
Cc: stable@vger.kernel.org
Fixes: 67809f85d3 ("ahci: disable NCQ on Samsung pci-e SSDs on macbooks")
This reverts commit 33fb0d01ce.
18dcf433f3 ("AHCI: Optimize single IRQ interrupt processing") is
scheduled to be reverted. This is an optimization dependent on the
mentioned commit. Revert it first.
Signed-off-by: Tejun Heo <tj@kernel.org>
Unlike other SATA R-Car r8a7790 controllers the r8a7790 ES1 SATA R-Car
controller needs to be run with DIPM disabled.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
The drivers should use dmaengine_terminate_all() API instead of accessing
the device_control which will be deprecated soon
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull libata update from Tejun Heo:
"AHCI is getting per-port irq handling and locks for better
scalability. The gain is not huge but measureable with multiple high
iops devices connected to the same host; however, the value of
threaded IRQ handling seems negligible for AHCI and it likely will
revert to non-threaded handling soon.
Another noteworthy change is George Spelvin's "libata: Un-break ATA
blacklist". During 3.17 devel cycle, the libata blacklist glob
matching got generalized and rewritten; unfortunately, the patch
forgot to swap arguments to match the new match function and ended up
breaking blacklist matching completely. It got noticed only a couple
days ago so it couldn't make for-3.17-fixes either. :(
Other than the above two, nothing too interesting - the usual cleanup
churns and device-specific changes"
* 'for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
pata_serverworks: disable 64-KB DMA transfers on Broadcom OSB4 IDE Controller
libata: Un-break ATA blacklist
AHCI: Do not acquire ata_host::lock from single IRQ handler
AHCI: Optimize single IRQ interrupt processing
AHCI: Do not read HOST_IRQ_STAT reg in multi-MSI mode
AHCI: Make few function names more descriptive
AHCI: Move host activation code into ahci_host_activate()
AHCI: Move ahci_host_activate() function to libahci.c
AHCI: Pass SCSI host template as arg to ahci_host_activate()
ata: pata_imx: Use the SIMPLE_DEV_PM_OPS() macro
AHCI: Cleanup checking of multiple MSIs/SLM modes
libata-sff: Fix controllers with no ctl port
ahci_xgene: Fix the error print invalid resource for APM X-Gene SoC AHCI SATA Host Controller driver.
libata: change ata_<foo>_printk routines to return void
ata: qcom: Add device tree bindings information
ahci-platform: Bump max number of clocks to 5
ahci: ahci_p5wdh_workaround - constify DMI table
libahci_platform: Staticize ahci_platform_<en/dis>able_phys()
pata_platform: Remove useless irq_flags field
pata_of_platform: Remove "electra-ide" quirk
...
These are bug fixes for harmless problems that were not important
enough to get fixed in 3.17. The majority of these are OMAP specific,
but there are also a couple for Marvell mvebu, cns3xxx, and others,
as well as some updates for the MAINTAINERS file.
In particular, Robert Jarzmik and Daniel Mack now volunteered to help
out maintaining the PXA platform, Krzysztof Halasa took over the
cns3xxx platform, Carlo Caione is the maintainer for the new Amlogic
meson platform, and Matthias Brugger is now listed for the mediatek
platform he recently contributed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Smzi
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical bug fixes from Arnd Bergmann:
"These are bug fixes for harmless problems that were not important
enough to get fixed in 3.17. The majority of these are OMAP specific,
but there are also a couple for Marvell mvebu, cns3xxx, and others, as
well as some updates for the MAINTAINERS file.
In particular, Robert Jarzmik and Daniel Mack now volunteered to help
out maintaining the PXA platform, Krzysztof Halasa took over the
cns3xxx platform, Carlo Caione is the maintainer for the new Amlogic
meson platform, and Matthias Brugger is now listed for the mediatek
platform he recently contributed"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
MAINTAINERS: update Shawn's email address
MAINTAINERS: condense some Tegra related entries
MAINTAINERS: add Alexandre Courbot for Tegra
MAINTAINERS: CNS3xxx and IXP4xx update.
MAINTAINERS: Add maintainers entry for Mediatek SoCs
arm, vt8500, LLVMLlinux: Use mcr instead of mcr% for mach-vt8500
MAINTAINERS: add a third maintainer to mach-bcm
CNS3xxx: Fix PCIe read size limit.
CNS3xxx: Fix logical PCIe topology.
CNS3xxx: Fix debug UART.
MAINTAINERS: Add entry for the Amlogic MesonX SoCs
MAINTAINERS: update ARM pxa maintainers
ARM: at91/PMC: don't forget to write PMC_PCDR register to disable clocks
ARM: at91: fix at91sam9263ek DT mmc pinmuxing settings
ARM: mvebu: Netgear RN102: Use Hardware BCH ECC
ARM: Kirkwood: Fix DT based DSA.
ARM: OMAP2+: make of_device_ids const
ARM: omap2: make arrays containing machine compatible strings const
ARM: LPC32xx: Fix reset function
ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
...
The Broadcom OSB4 IDE Controller (vendor and device IDs: 1166:0211)
does not support 64-KB DMA transfers.
Whenever a 64-KB DMA transfer is attempted,
the transfer fails and messages similar to the following
are written to the console log:
[ 2431.851125] sr 0:0:0:0: [sr0] Unhandled sense code
[ 2431.851139] sr 0:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 2431.851152] sr 0:0:0:0: [sr0] Sense Key : Hardware Error [current]
[ 2431.851166] sr 0:0:0:0: [sr0] Add. Sense: Logical unit communication time-out
[ 2431.851182] sr 0:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 76 f4 00 00 40 00
[ 2431.851210] end_request: I/O error, dev sr0, sector 121808
When the libata and pata_serverworks modules
are recompiled with ATA_DEBUG and ATA_VERBOSE_DEBUG defined in libata.h,
the 64-KB transfer size in the scatter-gather list can be seen
in the console log:
[ 2664.897267] sr 9:0:0:0: [sr0] Send:
[ 2664.897274] 0xf63d85e0
[ 2664.897283] sr 9:0:0:0: [sr0] CDB:
[ 2664.897288] Read(10): 28 00 00 00 7f b4 00 00 40 00
[ 2664.897319] buffer = 0xf6d6fbc0, bufflen = 131072, queuecommand 0xf81b7700
[ 2664.897331] ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 7f b4 00 00 40
[ 2664.897338] ata_scsi_translate: ENTER
[ 2664.897345] ata_sg_setup: ENTER, ata1
[ 2664.897356] ata_sg_setup: 3 sg elements mapped
[ 2664.897364] ata_bmdma_fill_sg: PRD[0] = (0x66FD2000, 0xE000)
[ 2664.897371] ata_bmdma_fill_sg: PRD[1] = (0x65000000, 0x10000)
------------------------------------------------------> =======
[ 2664.897378] ata_bmdma_fill_sg: PRD[2] = (0x66A10000, 0x2000)
[ 2664.897386] ata1: ata_dev_select: ENTER, device 0, wait 1
[ 2664.897422] ata_sff_tf_load: feat 0x1 nsect 0x0 lba 0x0 0x0 0xFC
[ 2664.897428] ata_sff_tf_load: device 0xA0
[ 2664.897448] ata_sff_exec_command: ata1: cmd 0xA0
[ 2664.897457] ata_scsi_translate: EXIT
[ 2664.897462] leaving scsi_dispatch_cmnd()
[ 2664.897497] Doing sr request, dev = sr0, block = 0
[ 2664.897507] sr0 : reading 64/256 512 byte blocks.
[ 2664.897553] ata_sff_hsm_move: ata1: protocol 7 task_state 1 (dev_stat 0x58)
[ 2664.897560] atapi_send_cdb: send cdb
[ 2666.910058] ata_bmdma_port_intr: ata1: host_stat 0x64
[ 2666.910079] __ata_sff_port_intr: ata1: protocol 7 task_state 3
[ 2666.910093] ata_sff_hsm_move: ata1: protocol 7 task_state 3 (dev_stat 0x51)
[ 2666.910101] ata_sff_hsm_move: ata1: protocol 7 task_state 4 (dev_stat 0x51)
[ 2666.910129] sr 9:0:0:0: [sr0] Done:
[ 2666.910136] 0xf63d85e0 TIMEOUT
lspci shows that the driver used for the Broadcom OSB4 IDE Controller is
pata_serverworks:
00:0f.1 IDE interface: Broadcom OSB4 IDE Controller (prog-if 8e [Master SecP SecO PriP])
Flags: bus master, medium devsel, latency 64
[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
[virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
I/O ports at 0170 [size=8]
I/O ports at 0374 [size=4]
I/O ports at 1440 [size=16]
Kernel driver in use: pata_serverworks
The pata_serverworks driver supports five distinct device IDs,
one being the OSB4 and the other four belonging to the CSB series.
The CSB series appears to support 64-KB DMA transfers,
as tests on a machine with an SAI2 motherboard
containing a Broadcom CSB5 IDE Controller (vendor and device IDs: 1166:0212)
showed no problems with 64-KB DMA transfers.
This problem was first discovered when attempting to install openSUSE
from a DVD on a machine with an STL2 motherboard.
Using the pata_serverworks module,
older releases of openSUSE will not install at all due to the timeouts.
Releases of openSUSE prior to 11.3 can be installed by disabling
the pata_serverworks module using the brokenmodules boot parameter,
which causes the serverworks module to be used instead.
Recent releases of openSUSE (12.2 and later) include better error recovery and
will install, though very slowly.
On all openSUSE releases, the problem can be recreated
on a machine containing a Broadcom OSB4 IDE Controller
by mounting an install DVD and running a command similar to the following:
find /mnt -type f -print | xargs cat > /dev/null
The patch below corrects the problem.
Similar to the other ATA drivers that do not support 64-KB DMA transfers,
the patch changes the ata_port_operations qc_prep vector to point to a routine
that breaks any 64-KB segment into two 32-KB segments and
changes the scsi_host_template sg_tablesize element to reduce by half
the number of scatter/gather elements allowed.
These two changes affect only the OSB4.
Signed-off-by: Scott Carter <ccscott@funsoft.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Martin K. Petersen