If an admin requests disconnect at a time when the state handling
already disconnects/reconnects, there have been some races.
Make sure to always really stop the network threads before
returning success for disconnect. Do not pretend successfull
forced disconnect, if the state handling returned an error.
Return success from drbd_adm_down() only after all threads are finished.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Calling kobject_uevent, which may sleep, from within rcu_read_lock()
protected regions is not possible.
This particular kobject_uevent also is also wrong. It was supposed to
trigger a udev run, just in case something relevant to udev symlink
magic has changed, when adjusting runtime re-configurable settings while
we still had the "syncer conf". It was improperly placed in connect
when we dropped the "syncer conf". The right thing to do is probably to
call "udevadm trigger" directly in those cases where drbdadm thinks
there was a need to trigger extra udev runs.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
References hold by:
* Each (running) drbd thread has a reference on tconn
* Each mdev has a referenc on tconn
* Beeing in the all_tconn list counts for one reference
* Each after_conn_state_chg_work has a reference to tconn
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When the last volume of a replication group is unconfigured,
the worker thread exits. To not interfere with cleanup
of other threads, before the the last cleanups run,
we need to make sure the receiver has already exited.
The commend explaining that clearly belongs above
drbd_thread_stop(&tconn->receiver), not in the cleanup loop below.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We use our own copy of kernel_setsockopt, and did not mess around with
get_fs/set_fs, since we thought we knew we would always be KERNEL_DS
anyways. Apparently not so for at least user mode linux, so put the
set_fs(KERNEL_DS) in there.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We had drbd_adm_get_status (one single volume),
and drbd_adm_get_status_all (dump of all volumes of all resources).
This enhances the latter to be able to dump all volumes
of just one specific resource.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now since it is possible to change the two_primaries config
flag while the connection is up, make sure we treat a peer_req
in a consistent way if the config flag changes while the peer_req
is under IO.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Removing the get_net_conf()/put_net_conf() functions
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Removing the get_net_conf()/put_net_conf() calls
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The wire protocol is no longer a property that is negotiated
between the two peers. It is now expressed with two bits
(DP_SEND_WRITE_ACK and DP_SEND_RECEIVE_ACK) in each data
packet. Therefore the primary node is free to change the
wire protocol at any time without disconnect/reconnect.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
With this commit the locking for all accesses to IDRs is complete:
* Non sleeping read accesses are protected by RCU
* sleeping read accesses are protocted by a read lock on drbd_cfg_rwsem
* accesses that add anything are protected by a write lock
* accesses that remove an object are protoected by a write lock
and a call to synchronize_rcu() after it is removed from the IDR
and before the object is actually free()ed.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Since have now header 100, that has space for 16 bit volume numbers,
the high byte of the length in header 95 is no longer reserved for
8 bit volume numbers.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The 8 byte header finally becomes too small. With the protocol 100 header we
have 16 bit for the volume number, proper 32 bit for the data length, and
32 bit for further extensions in the future.
Previous versions of drbd are using version 80 headers for all packets
short enough for protocol 80. They support both header versions in
worker context, but only version 80 headers in asynchronous context.
For backwards compatibility, continue to use version 80 headers for
short packets before protocol version 100.
From protocol version 100 on, use the same header version for all
packets.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Prepare the introduction of the protocol 100 headers. The actual protocol
header is removed for the packet declarations. I.e. allow us to use the
packets with different headers.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Centralize sock->mutex locking and unlocking in [drbd|conn]_prepare_command()
and [drbd|conn]_send_comman().
Therefore all *_send_* functions are touched to use these primitives instead
of drbd_get_data_sock()/drbd_put_data_sock() and former helper functions.
That change makes the *_send_* functions more standardized.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Lars Ellenberg