Documentation/networking/switchdev.txt and 'man bridge' indicate that the
learning_sync bridge attribute is used to control whether a given
device will sync MAC addresses learned on its device port to a master
bridge FDB, where they will show up as 'extern_learn offload'. So we map
qeth_l2_dev2br_an_set() to the learning_sync bridge link attribute.
Turning off learning_sync will flush all extern_learn entries from the
bridge fdb and all pending events from the card's work queue.
When the hardware interface goes offline with learning_sync on
(e.g. for HW recovery), all extern_learn entries will be flushed from the
bridge fdb and all pending events from the card's work queue. When the
interface goes online again, it will send new notifications for all then
valid MACs. learning_sync attribute can not be modified while interface is
offline. See
'commit e6e771b3d8 ("s390/qeth: detach netdevice while card is offline")'
An alternative implementation would be to always offload the 'learning'
attribute of a software bridge to the hardware interface attached to it
and thus implicitly enable fdb notification. This was not chosen for 2
reasons:
1) In our case the software bridge is NOT a representation of a hardware
switch. It is just connected to a smart NIC that is able to inform
about the addresses attached to it. It is not necessarily using source
MAC learning for this and other bridgeports can be attached to other
NICs with different properties.
2) We want a means to enable this notification explicitly. There may be
cases where a bridgeport is set to 'learning', but we do not want to
enable the notification.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/networking/switchdev.txt and 'man bridge' indicate that the
learning_sync bridge attribute is used to indicate whether a given
device will sync MAC addresses learned on its device port to a master
bridge FDB.
learning_sync attribute can not be read while interface is offline (down).
See
'commit e6e771b3d8 ("s390/qeth: detach netdevice while card is offline")'
We return EOPNOTSUPP and not EONODEV in this case, because EONOTSUPP is the
only rc that is tolerated by 'bridge -d link show'.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case hardware sends more device-to-bridge-address-change notfications
than the qeth-l2 driver can handle, the hardware will send an overflow
event and then stop sending any events. It expects software to flush its
FDB and start over again. Re-enabling address-change-notification will
report all current addresses.
In order to re-enable address-change-notification this patch defines
the functions qeth_l2_dev2br_an_set() and qeth_l2_dev2br_an_set_cb
to enable or disable dev-to-bridge-address-notification.
A following patch will use the learning_sync bridgeport flag to trigger
enabling or disabling of address-change-notification, so we define
priv->brport_features to store the current setting. BRIDGE_INFO and
ADDR_INFO functionality are mutually exclusive, whereas ADDR_INFO and
qeth_l2_vnicc* can be used together.
Alternative implementations to handle buffer overflow:
Just re-enabling notification and adding all newly reported addresses
would cover any lost 'add' events, but not the lost 'delete' events.
Then these invalid addresses would stay in the bridge FDB as long as the
device exists.
Setting the net device down and up, would be an alternative, but is a bit
drastic. If the net device has many secondary addresses this will create
many delete/add events at its peers which could de-stabilize the
network segment.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A qeth-l2 HiperSockets card can show switch-ish behaviour in the sense,
that it can report all MACs that are reachable via this interface. Just
like a switch device, it can notify the software bridge about changes
to its fdb. This patch exploits this device-to-bridge-notification and
extracts the relevant information from the hardware events to generate
notifications to an attached software bridge.
There are 2 sources for this information:
1) The reply message of Perform-Network-Subchannel-Operations (PNSO)
(operation code ADDR_INFO) reports all addresses that are currently
reachable (implemented in a later patch).
2) As long as device-to-bridge-notification is enabled, hardware will
generate address change notification events, whenever the content of
the hardware fdb changes (this patch).
The bridge_hostnotify feature (PNSO operation code BRIDGE_INFO) uses
the same address change notification events. We need to distinguish
between qeth_pnso_mode QETH_PNSO_BRIDGEPORT and QETH_PNSO_ADDR_INFO
and call a different handler. In both cases deadlocks must be
prevented, if the workqueue is drained under lock and QETH_PNSO_NONE,
when notification is disabled.
bridge_hostnotify generates udev events, there is no intend to do the same
for dev2br. Instead this patch will generate SWITCHDEV_FDB_ADD_TO_BRIDGE
and SWITCHDEV_FDB_DEL_TO_BRIDGE notifications, that will cause the
software bridge to add (or delete) entries to its fdb as 'extern_learn
offload'.
Documentation/networking/switchdev.txt proposes to add
"depends NET_SWITCHDEV" to driver's Kconfig. This is not done here,
so even in absence of the NET_SWITCHDEV module, the QETH_L2 module will
still be built, but then the switchdev notifiers will have no effect.
No VLAN filtering is done on the entries and VLAN information is not
passed on to the bridge fdb entries. This could be added later.
For now VLAN interfaces can be defined on the upper bridge interface.
Multicast entries are not passed on to the bridge fdb.
This could be added later. For now mcast flooding can be used in the
bridge.
The card reports all MACs that are in its FDB, but we must not pass on
MACs that are registered for this interface.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch detects whether device-to-bridge-notification, provided
by the Perform Network Subchannel Operation (PNSO) operation code
ADDR_INFO (OC3), is supported by this card. A following patch will
map this to the learning_sync bridgeport flag, so we store it in
priv->brport_hw_features in bridgeport flag format.
Only IQD cards provide PNSO.
There is a feature bit to indicate whether the machine provides OC3,
unfortunately it is not set on old machines.
So PNSO is called to find out. As this will disable notification
and is exclusive with bridgeport_notification, this must be done
during card initialisation before previous settings are restored.
PNSO functionality requires some configuration values that are added to
the qeth_card.info structure. Some helper functions are defined to fill
them out when the card is brought online and some other places are
adapted, that can also benefit from these fields.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for operation code 3 (OC3) of the
Perform-Network-Subchannel-Operations (PNSO) function
of the Channel-Subsystem-Call (CHSC) instruction.
PNSO provides 2 operation codes:
OC0 - BRIDGE_INFO
OC3 - ADDR_INFO (new)
Extend the function calls to *pnso* to pass the OC and
add new response code 0108.
Support for OC3 is indicated by a flag in the css_general_characteristics.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arch/s390/net/pnet.c uses ccwgroup function dev_is_ccwgroup()
in pnetid_by_dev_port().
For s390 the net/smc code makes use of function pnetid_by_dev_port().
Make sure ccwgroup is built into the kernel, if smc is to be built
into the kernel.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current code for bridge address events has two shortcomings in its
control sequence:
1. after disabling address events via PNSO, we don't flush the remaining
events from the event_wq. So if the feature is re-enabled fast
enough, stale events could leak over.
2. PNSO and the events' arrival via the READ ccw device are unordered.
So even if we flushed the workqueue, it's difficult to say whether
the READ device might produce more events onto the workqueue
afterwards.
Fix this by
1. explicitly fencing off the events when we no longer care, in the
READ device's event handler. This ensures that once we flush the
workqueue, it doesn't get additional address events.
2. Flush the workqueue after disabling the events & fencing them off.
As the code that triggers the flush will typically hold the sbp_lock,
we need to rework the worker code to avoid a deadlock here in case
of a 'notifications-stopped' event. In case of lock contention,
requeue such an event with a delay. We'll eventually aquire the lock,
or spot that the feature has been disabled and the event can thus be
discarded.
This leaves the theoretical race that a stale event could arrive
_after_ we re-enabled ourselves to receive events again. Such an event
would be impossible to distinguish from a 'good' event, nothing we can
do about it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data returned from IPA_SBP_QUERY_BRIDGE_PORTS and
IPA_SBP_BRIDGE_PORT_STATE_CHANGE has the same format. Use a single
struct definition for it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code copies _all_ entries from the event into a worker, when we
later only need specific data from the first entry.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only time that our Bridgeport role should change is when we change
the configuration ourselves. In which case we also adjust our internal
state tracking, no need to do it again when we receive the corresponding
event.
Removing the locked section helps a subsequent patch that needs to flush
the workqueue while under sbp_lock.
It would be nice to raise a warning here in case HW does weird things
after all, but this could end up generating false-positives when we
change the configuration ourselves.
Suggested-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A newly initialized device is disabled for address events, there's no
need to explicitly disable them.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
queue->state is a ternary spinlock in disguise, used by
OSA's TX completion path to lock the Output Queue and flush any pending
packets on it to the device. If the Queue is already locked by our TX
code, setting the lock word to QETH_OUT_Q_LOCKED_FLUSH lets the TX
completion code move on - the TX path will later take care of things
when it unlocks the Queue.
This sort of DIY locking is a non-starter of course, just let the
TX completion path block on the spinlock when necessary. If that ends up
causing additional latency due to lock contention, then converting
the OSA path to use xmit_more is the right way to go forward.
Also slightly expand the locked section and capture all of
qeth_do_send_packet(), so that the update for the 'bufs_pack' statistics
is done race-free.
While reworking the TX completion path's code, remove a barrier() that
doesn't make any sense.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid poking around in the delayed_work struct's internals.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clarify that the 'ipacmd' parameter is an enum, and thus compatible to
what qeth_ipa_alloc_cmd() expects as input.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The (misplaced) comment doesn't make any sense, enforcing an
uninitialized RX buffer won't help with IRQ reduction.
So make the best use of all available RX buffers.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Discard events that don't contain any entries. This shouldn't happen,
but subsequent code relies on being able to use entry 0. So better
be safe than accessing garbage.
Fixes: b4d72c08b3 ("qeth: bridgeport support - basic control")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Running a RX refill outside of NAPI context is inherently racy, even
though the worker is only started for an entirely idle RX ring.
>From the moment that the worker has replenished parts of the RX ring,
the HW can use those RX buffers, raise an IRQ and cause our NAPI code to
run concurrently to the RX refill worker.
Instead let the worker schedule our NAPI instance, and refill the RX
ring from there. Keeping accurate count of how many buffers still need
to be refilled also removes some quirky arithmetic from the low-level
code.
Fixes: b333293058 ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When preparing a buffer for RX refill, tolerate that it already has a
pool_entry attached. Otherwise we could easily leak such a pool_entry
when re-driving the RX refill after an error (from eg. do_qdio()).
This needs some minor adjustment in the code that drains RX buffer(s)
prior to RX refill and during teardown, so that ->pool_entry is NULLed
accordingly.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ism driver allocates a new dmb in ism_alloc_dmb() it must
first check for and reserve a slot in the sba bitmap. When
find_next_zero_bit() finds no free slot then the return code is -ENOMEM.
This code conflicts with the error when the alloc() fails later in the
code. As a result of that the caller can not differentiate
between out-of-memory conditions and sba-bitmap-full conditions.
Fix that by using the return code -ENOSPC when the sba slot
reservation failed.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're not modifying these data blobs, so mark them as constant.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To keep track of the addresses programmed from an RX modeset, we have
two separate hashtables (L2: mac_htable, L3: ip_mc_htable).
These are never used at the same time, so unify them into a single
rx_mode_addrs hashtable.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While initially just trying to fix up the indentation, condense a few
lines and get rid of a goto label.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the correct struct member instead of hardcoding its offset.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the correct helper for casting to a user pointer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the cmd IO path has learned to propagate errnos back to its callers,
let them deal with errors instead of trying to restore their previous
configuration from within the IO error path.
Also translate the HW error to a meaningful errno, instead of returning
-EIO for all cases (and don't map this to -EOPNOTSUPP later on...).
While at it, add a READ_ONCE() / WRITE_ONCE() pair to ensure that the
data path always sees a valid isolation mode during reconfiguration.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When qeth_set_access_ctrl_online() is called during the device's
initialization and discovers that isolation mode isn't supported, don't
clear the user's currently configured mode.
They intentionally choose to operate the device in this specific mode,
and degrading the isolation is not an option.
Only adjust the configuration when called via sysfs (ie. fallback = 1),
and here follow the common pattern and restore it from prev_isolation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A newly initialized device defaults to ISOLATION_MODE_NONE, don't bother
with programming this a second time.
Then remove the OSD/OSX check, it's already done in the sysfs path
whenever the user actually changes the configuration.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we cancel all pending cmds (eg. when tearing down the device), don't
blame it on an IO error.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than delaying the decision until netdev setup, immediately reject
a device when we discover that it has an unsupported link type
(ie. Token Ring).
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a device is configured with ISOLATION_MODE_FWD, traffic never goes
through the internal switch. Don't apply the offload restrictions in
this case.
Fixes: c619e9a6f5 ("s390/qeth: don't use restricted offloads for local traffic")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current(?) OSA devices also store their cmd-specific return codes for
SET_ACCESS_CONTROL cmds into the top-level cmd->hdr.return_code.
So once we added stricter checking for the top-level field a while ago,
none of the error logic that rolls back the user's configuration to its
old state is applied any longer.
For this specific cmd, go back to the old model where we peek into the
cmd structure even though the top-level field indicated an error.
Fixes: 686c97ee29 ("s390/qeth: fix error handling in adapter command callbacks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add support for multi-function devices in pci code.
- Enable PF-VF linking for architectures using the
pdev->no_vf_scan flag (currently just s390).
- Add reipl from NVMe support.
- Get rid of critical section cleanup in entry.S.
- Refactor PNSO CHSC (perform network subchannel operation) in cio
and qeth.
- QDIO interrupts and error handling fixes and improvements, more
refactoring changes.
- Align ioremap() with generic code.
- Accept requests without the prefetch bit set in vfio-ccw.
- Enable path handling via two new regions in vfio-ccw.
- Other small fixes and improvements all over the code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl7eVGcACgkQjYWKoQLX
FBhweQgAkicvx31x230rdfG+jQkQkl0UqF99vvWrJHEll77SqadfjzKAGIjUB+K0
EoeHVD5Wcj7BogDGcyHeQ0bZpu4WzE+y1nmnrsvu7TEEvcBmkJH0rF2jF+y0sb/O
3qvwFkX/CB5OqaMzKC/AEeRpcCKR+ZUXkWu1irbYth7CBXaycD9EAPc4cj8CfYGZ
r5njUdYOVk77TaO4aV+t5pCYc5TCRJaWXSsWaAv/nuLcIqsFBYOy2q+L47zITGXp
utZVanIDjzx+ikpaKicOIfC3hJsRuNX9MnlZKsQFwpVEZAUZmIUm29XdhGJTWSxU
RV7m1ORINbFP1nGAqWqkOvGo/LC0ZA==
=VhXR
-----END PGP SIGNATURE-----
Merge tag 's390-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Add support for multi-function devices in pci code.
- Enable PF-VF linking for architectures using the pdev->no_vf_scan
flag (currently just s390).
- Add reipl from NVMe support.
- Get rid of critical section cleanup in entry.S.
- Refactor PNSO CHSC (perform network subchannel operation) in cio and
qeth.
- QDIO interrupts and error handling fixes and improvements, more
refactoring changes.
- Align ioremap() with generic code.
- Accept requests without the prefetch bit set in vfio-ccw.
- Enable path handling via two new regions in vfio-ccw.
- Other small fixes and improvements all over the code.
* tag 's390-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (52 commits)
vfio-ccw: make vfio_ccw_regops variables declarations static
vfio-ccw: Add trace for CRW event
vfio-ccw: Wire up the CRW irq and CRW region
vfio-ccw: Introduce a new CRW region
vfio-ccw: Refactor IRQ handlers
vfio-ccw: Introduce a new schib region
vfio-ccw: Refactor the unregister of the async regions
vfio-ccw: Register a chp_event callback for vfio-ccw
vfio-ccw: Introduce new helper functions to free/destroy regions
vfio-ccw: document possible errors
vfio-ccw: Enable transparent CCW IPL from DASD
s390/pci: Log new handle in clp_disable_fh()
s390/cio, s390/qeth: cleanup PNSO CHSC
s390/qdio: remove q->first_to_kick
s390/qdio: fix up qdio_start_irq() kerneldoc
s390: remove critical section cleanup from entry.S
s390: add machine check SIGP
s390/pci: ioremap() align with generic code
s390/ap: introduce new ap function ap_get_qdev()
Documentation/s390: Update / remove developerWorks web links
...
CHSC3D (PNSO - perform network subchannel operation) is used for
OC0 (Store-network-bridging-information) as well as for
OC3 (Store-network-address-information). So common fields are renamed
from *brinfo* to *pnso*.
Also *_bridge_host_* is changed into *_addr_change_*, e.g.
qeth_bridge_host_event to qeth_addr_change_event, for the
same reasons.
The keywords in the card traces are changed accordingly.
Remove unused L3 types, as PNSO will only return Layer2 entries.
Make PNSO CHSC implementation more consistent with existing API usage:
Add new function ccw_device_pnso() to drivers/s390/cio/device_ops.c and
the function declaration to arch/s390/include/asm/ccwdev.h, which takes
a struct ccw_device * as parameter instead of schid and calls
chsc_pnso().
PNSO CHSC has no strict relationship to qdio. So move the calling
function from qdio to qeth_l2 and move the necessary structures to a
new file arch/s390/include/asm/chsc.h.
Do response code evaluation only in chsc_error_from_response() and
use return code in all other places. qeth_anset_makerc() was meant to
evaluate the PNSO response code, but never did, because pnso_rc was
already non-zero.
Indentation was corrected in some places.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Commit 394216275c ("s390: remove broken hibernate / power management support")
removed support for ARCH_HIBERNATION_POSSIBLE on s390.
So drop the unused pm ops from the iucv drivers.
CC: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 5e1fb45ec8 ("s390/ccwgroup: remove pm support") removed power
management support from the ccwgroup bus driver. So remove the
associated callbacks from all ccwgroup drivers.
CC: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bpf verifier trace check into the new switch statement in
HEAD.
Resolve the overlapping changes in hinic, where bug fixes overlap
the addition of VF support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return negative error code -ENOMEM from the smcd_alloc_dev()
error handling case instead of 0, as done elsewhere in this function.
Fixes: 684b89bc39 ("s390/ism: add device driver for internal shared memory")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a stale doc link. While at it also reword the help text to get
rid of an outdated marketing term.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When starting the reset worker via sysfs is unsuccessful, return an
error to the user.
Modernize the sysfs input parsing while at it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When qeth_flush_buffers() gets called for a group of TX buffers
(currently up to 2 for OSA-style devices), the code iterates over each
buffer for some final processing.
During this processing, it sets the TX IRQ marker on the leading buffer
rather than the last one. This can result in delayed TX completion of
the trailing buffers. So pull the IRQ marker code out of the loop, and
apply it to the final buffer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX path usually maps the full content of a page into a buffer
element. But there's specific skb layouts (ie. linearized TSO skbs)
where the HW header (1) requires a separate buffer element, and (2) is
page-contiguous with the packet data that's mapped into the next buffer
element.
Flag such buffer elements accordingly, so that HW can optimize its data
access for them.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the __qeth_fill_buffer() helper into its only caller. This way all
mapping-related context is in one place, and we can make some more use
of it in a subsequent patch.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current OSA models don't support TSO for traffic to local next-hops, and
some old models didn't offer TX CSO for such packets either.
So as part of .ndo_features_check, check if a packet's next-hop resides
on the same OSA Adapter. Opt out from affected HW offloads accordingly.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For debugging purposes, provide read access to the local_addr caches
via debug/qeth/<dev_name>/local_addrs.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In configurations where specific HW offloads are in use, OSA adapters
will raise notifications to their virtual devices about the IP addresses
that currently reside on the same adapter.
Cache these addresses in two RCU-enabled hash tables, and flush the
tables once the relevant HW offload(s) get disabled.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandra Winter