Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If st_kim_start() fails registered protocols should be removed. This is
done by calling st_reg_complete(), which as comment states is called
with spin lock held. But in st_register() when st_kim_start fails it
is called without holding spin lock, creating possibility of concurrent
access to st_gdata data members.
Hold spin lock while calling st_reg_complete if st_kim_start() fails.
Signed-off-by: Oleksandr Kozaruk <oleksandr.kozaruk@globallogic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei, hyperv, ipack,
extcon, vmci, etc.).
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZJgACgkQMUfUDdst+ymhZgCgo2dn37r9uMCwgTSpxSq92Je5
x8kAnRF1UnD6ZvySRIlLUBV5LW1YgFnK
=i5HH
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg Kroah-Hartman:
"Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei,
hyperv, ipack, extcon, vmci, etc.).
All of these have been in the linux-next tree for a while."
* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
w1: w1_therm: Add force-pullup option for "broken" sensors
w1: ds2482: Added 1-Wire pull-up support to the driver
vme: add missing put_device() after device_register() fails
extcon: max8997: Use workqueue to check cable state after completing boot of platform
extcon: max8997: Set default UART/USB path on probe
extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
extcon: max8997: Set default of ADC debounce time during initialization
extcon: max8997: Remove duplicate code related to set H/W line path
extcon: max8997: Move defined constant to header file
extcon: max77693: Make max77693_extcon_cable static
extcon: max8997: Remove unreachable code
extcon: max8997: Make max8997_extcon_cable static
extcon: max77693: Remove unnecessary goto statement to improve readability
extcon: max77693: Convert to devm_input_allocate_device()
extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
CREDITS: update email and address of Harald Hoyer
extcon: arizona: Use MICDET for final microphone identification
extcon: arizona: Always take the first HPDET reading as the final one
extcon: arizona: Clear _trig_sts bits after jack detection
extcon: arizona: Don't HPDET magic when headphones are enabled
...
This reverts commit eccf2979b2.
The reason is that it broke TI WiLink shared transport on Panda.
Also, callback functions should not be added to board files anymore,
so revert to implementing the power functions in the driver itself.
Additionally, changed a variable name ('status' to 'err') so that this
revert compiles properly.
Cc: stable <stable@vger.kernel.org> [3.7]
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit eccf2979b2.
The reason is that it broke TI WiLink shared transport on Panda.
Also, callback functions should not be added to board files anymore,
so revert to implementing the power functions in the driver itself.
Additionally, changed a variable name ('status' to 'err') so that this
revert compiles properly.
Cc: stable <stable@vger.kernel.org> [3.7]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.
The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer. Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.
bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY. The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.
add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function old new delta
chr_dev_init 166 170 +4
allow_signal 80 82 +2
static.__warned 143 142 -1
disallow_signal 63 62 -1
__set_special_pids 95 94 -1
unregister_console 126 121 -5
start_kernel 546 541 -5
register_console 593 588 -5
copy_from_user 45 40 -5
sys_setsid 128 120 -8
sys_vhangup 32 19 -13
do_exit 1543 1526 -17
bitmap_zero 60 40 -20
arch_local_irq_save 137 117 -20
release_task 674 652 -22
static.spin_unlock_irqrestore 308 260 -48
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When st driver decodes protocol index received from raw data,
it does a value convert from "char" to "int". Because it's sign
extension from bit8 to bit32, the "int" value maybe minus, in
another word, the protocol index might be minus, but driver doesn't
filter such case and may continue access memory pointed by this
minus index.
This patch is to change the variable type of index from "int"
to "unsigned char", so that it avoids do such kind of type
conversion.
cc: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the pointless NULL dereference above the NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before calling on any of the platform hooks, shared transport driver checks
for the validity of the platform hooks as to whether it is provided or not.
A wrong function was being checked for, before the chip_awake hook was called
by the HCI-LL sleep logic handler. This patch corrects the check.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the read firmware version response from the chip is split into multiple
frames of UART buffer being received by the host, the TI-ST driver as of today
is unable to put the pieces of response together unlike other responses.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Be nice to CPU and don't hog the resources, use a nice wait_for_interruptible
timeout for completions instead of wait_for_timeout which is
non-interruptible.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the communication with the WiLink breaks down for whatever reasons & the
ti-st driver is unable to un-install the line-discipline during clean-up in
st_kim_stop, the GPIO should be held low (BT_EN=0) & the platform's chip
disable hook shall also be called.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
remove sparse warnings by assigning right storage specifiers to functions and
also clean-up the declarations in the include/linux/ti_wilink_st.h
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A platform hook to enable/disable the chip was introduced to perform specific
activities to power-up and power-down the WL chip.
Moving the power-up/down sequence also there makes more sense, since different
platforms have begun to have their own ways to power-up/down the chip.
This patch removes all of the gpio handling done by the driver in
st_kim_start/st_kim_stop & any of the gpio request done in the probe function.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch converts the drivers in drivers/misc/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Pavan Savoy <pavan_savoy@ti.com>
Cc: Donggeun Kim <dg77.kim@samsung.com>
Acked-By: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To debug different UARTs at different baud-rates connected to the WiLink
connectivity combo-chipset, this patch enables the debugging code so that upon
boot different UARTs at different baud-rates can be tried out to verify the
interface with WiLink.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Upon failure to read firmware version from chip or upon failure in responses
to firmware download the UART needs to be flushed of its existing buffers so
that the UIM can restart UART properly.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Concurrent access to UART2/combo-interface by multiple protocol drivers such
as BT, FM and GPS caused issues during firmware download failure cases or
cases when the firmware download took longer than usual.
This was because of un-safe access to protos_registered & st_states.
Protecting this will also make the registration complete callback un-safe for
sleep.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These files really need the full module.h header file present, but
were just getting it implicitly before. Fix it up in advance so we
avoid build failures once the cleanup commit is present.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
If suppose the UIM were to die and hence UART were to close when the
Bluetooth/FM or GPS is turned on, prep the ST for a state where-in if
the UIM comes back up, Bluetooth/FM/GPS can be turned on.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If during validation of the firmware download the data doesn't match what is
expected out of the chip, this calls for a firmware download failure and a
retry.
Free the SKB which collects response during such scenarios.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the line discipline install fails for reasons such as missing user-space
UIM or broken communication between UIM and ST driver, then the ST
attempts/retries to request for ldisc installation again.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
download firmware behaves differently at different times, when logs are
enabled and the system is loaded, the wait_for_completion is able to wait for
every send, However during other times the wait does not happen.
So, for reliability reinitializing the completion before every send, makes
sure the wait happens for every send.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Texas Instrument's shared transport driver interpret incoming data from the
UART based on the various protocol drivers registered to the driver such as
btwilink driver or FM or GPS driver which provide logical channel IDs.
In case of bad-behavior from chip such as HCI Event response for a GPS command
or a HCI Event (h/w error event) for a FM response & In case of bad-behavior
from UART driver such as dropping data bytes a fail-safe is required to avoid
kernel panic.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Vijay Badawadagi <bvijay@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After the version information has been read, the completion which assists in
wait_for_completion during the firmware send/wait sequence is being re-used
and hence this needs to be re-initialised for fool proof firmware download
retries.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Certain platform specific or Host-WiLink Interface specific actions would be
required to be taken when the chip is being enabled and after the chip is
disabled such as configuration of the mux modes for the GPIO of host connected
to the nshutdown of the chip or relinquishing UART after the chip is disabled.
Similar actions can also be taken when the chip is in deep sleep or when the
chip is awake. Performance enhancements such as configuring the host to run
faster when chip is awake and slower when chip is asleep can also be made
here.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Previously the private data of each protocol registered to use ST was
used to determine whether the protocol was registered to use shared
transport or otherwise.
However, now a flag is_registered is maintained to identify whether a
protocol intends to use ST.
Upon closing of the UART the error message relevant to this lack of
un-registration was misleading and this patch fixes that.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before the incrementing of ptr in skip_change_remote_baud,
it points to cur_action, but the increment is done by
the size of nxt_action instead. This could cause ptr
to not point to a bts_action structure, which is
harmful for the increment of ptr done in download_firmware.
Therefore, the skipping is first done for cur_action.
Signed-off-by: Shahar Lev <shahar@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit b1c43f82c5.
It was broken in so many ways, and results in random odd pty issues.
It re-introduced the buggy schedule_work() in flush_to_ldisc() that can
cause endless work-loops (see commit a5660b41af6a: "tty: fix endless
work loop when the buffer fills up").
It also used an "unsigned int" return value fo the ->receive_buf()
function, but then made multiple functions return a negative error code,
and didn't actually check for the error in the caller.
And it didn't actually work at all. BenH bisected down odd tty behavior
to it:
"It looks like the patch is causing some major malfunctions of the X
server for me, possibly related to PTYs. For example, cat'ing a
large file in a gnome terminal hangs the kernel for -minutes- in a
loop of what looks like flush_to_ldisc/workqueue code, (some ftrace
data in the quoted bits further down).
...
Some more data: It -looks- like what happens is that the
flush_to_ldisc work queue entry constantly re-queues itself (because
the PTY is full ?) and the workqueue thread will basically loop
forver calling it without ever scheduling, thus starving the consumer
process that could have emptied the PTY."
which is pretty much exactly the problem we fixed in a5660b41af.
Milton Miller pointed out the 'unsigned int' issue.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Milton Miller <miltonm@bga.com>
Cc: Stefan Bigler <stefan.bigler@keymile.com>
Cc: Toby Gray <toby.gray@realvnc.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (48 commits)
serial: 8250_pci: add support for Cronyx Omega PCI multiserial board.
tty/serial: Fix break handling for PORT_TEGRA
tty/serial: Add explicit PORT_TEGRA type
n_tracerouter and n_tracesink ldisc additions.
Intel PTI implementaiton of MIPI 1149.7.
Kernel documentation for the PTI feature.
export kernel call get_task_comm().
tty: Remove to support serial for S5P6442
pch_phub: Support new device ML7223
8250_pci: Add support for the Digi/IBM PCIe 2-port Adapter
ASoC: Update cx20442 for TTY API change
pch_uart: Support new device ML7223 IOH
parport: Use request_muxed_region for IT87 probe and lock
tty/serial: add support for Xilinx PS UART
n_gsm: Use print_hex_dump_bytes
drivers/tty/moxa.c: Put correct tty value
TTY: tty_io, annotate locking functions
TTY: serial_core, remove superfluous set_task_state
TTY: serial_core, remove invalid test
Char: moxa, fix locking in moxa_write
...
Fix up trivial conflicts in drivers/bluetooth/hci_ldisc.c and
drivers/tty/serial/Makefile.
I did the hci_ldisc thing as an evil merge, cleaning things up.
st_drv uses skb*() interfaces, so it should depend on NET.
It also uses GPIO interfaces, so it should depend on GPIOLIB.
st_kim.c uses syss_*() calls, so it should #include
<linux/sysfs.h>.
Fixes these observed build errors:
ERROR: "skb_queue_purge" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "skb_pull" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "skb_queue_tail" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "__alloc_skb" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "kfree_skb" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "skb_dequeue" [drivers/misc/ti-st/st_drv.ko] undefined!
ERROR: "skb_put" [drivers/misc/ti-st/st_drv.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it makes it simpler to keep track of the amount of
bytes received and simplifies how flush_to_ldisc counts
the remaining bytes. It also fixes a bug of lost bytes
on n_tty when flushing too many bytes via the USB
serial gadget driver.
Tested-by: Stefan Bigler <stefan.bigler@keymile.com>
Tested-by: Toby Gray <toby.gray@realvnc.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
rfkill is no longer used by Texas Instruments shared transport driver to
communicate with user-space.
This patch removes the dependency of rfkill to be enabled to build
shared transport driver in the Kconfig.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When certain technologies shutdown their interface without waiting for
the acknowledgement from the chip. The receive_buf from the TTY would be
invoked a while after the relevant technology is unregistered.
This patch introduces a new flag "is_registered" which maintains the
state of protocols BT, FM or GPS and thereby removes the need to clear
the protocol data from ST when protocols gets unregistered.
This fixes corner cases when HCI RESET is sent down from bluetooth stack
and the receive_buf is called from tty after 250ms before which
bluetooth would have unregistered from the system.
OR - when FM application decides to close down the device without
sending a power-off FM command resulting in some RDS data or interrupt
data coming in after the driver is unregistered.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
debug code in TI-ST driver can be enabled by #defining
DEBUG in the first line of the code and in case debugfs
is mounted, the 2 entries in /sys/kernel/debug/ti-st/ will
also provide useful information.
These 2 were broken because of the recent changes to the parsing
logic and the registration mechanism of the protocol drivers,
this patch fixes them.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
TI shared transport driver previously intended to expose rfkill
entries for each of the protocol gpio that the chip would have.
However now in case such gpios exist, which requires to be enabled
for a specific protocol, the responsibility lay on protocol driver.
This patch removes the request/free of multiple gpios, rfkill struct
references and also removes the chip_toggle function.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Where file-transfer stops/pauses in between, is
result of a HCI-LL anamoly in ST LL driver.
ST LL did not copy the contents of WaitQ into the TxQ, when a WAKEUP_IND
collision happened.
Make also sure, that the copying mechanism is safe, by wrapping it around
spin locks inside st_int_recv().
This was easily reproduced when the sleep timeout was reduced to 100ms
for HCI-LL.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To fasten the process of firmware download, the chip allows
disabling of the command complete event generation from host.
In these cases, only few very essential commands would have
the command complete events and hence the wait associated with
them.
So now the driver would wait for a command complete event, only
when it comes across a wait event during firmware parsing.
This would also mean we need to skip not just the change baud
rate command but also the wait for it.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pr_debug-ing few pr_infos from the data paths such as tty receive and
write so as to reduce debugs when we have higher logging levels enabled
undef VERBOSE in receive to avoid huge logs when log level 8 is set.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
set-right the error codes that the shared transport driver
returns.
Instead of magic numbers like -1, return relevant codes such as
ETIMEDOUT or EIO, EAGAIN when wait times out or uart write bytes don't
match expected value or when registration fails and needs to be
attempted again.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The communication between ST KIM and UIM was interfaced
over the /dev/rfkill device node.
Move the interface to a simpler less abusive sysfs entry
mechanism and document it in Documentation/ABI/testing/
under sysfs-platform-kim.
Shared transport driver would now read the UART details
originally received by bootloader or firmware as platform
data.
The data read will be shared over sysfs entries for the user-space
UIM or other n/w manager/plugins to be read, and assist the driver
by opening up the UART, setting the baud-rate and installing the
line discipline.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The architecture of shared transport had begun with individual
protocols like bluetooth, fm and gps telling the shared transport
what sort of protocol they are and then expecting the ST driver
to parse the incoming data from chip and forward data only
relevant to the protocol drivers.
This change would mean each protocol drivers would also send
information to ST driver as to how to intrepret their protocol
data coming out of the chip.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on comments from Jiri Slaby, drop the register
storage specifier, remove the unused code, cleanup
the const to non-const type casting.
Also make the line discipline ops structure static, since
its a singleton, unmodified structure which need not be
in heap.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the Kconfig and the Makefile for the TI_ST driver.
TI_ST driver is the line discipline driver for the Texas Instrument's
WiLink chipsets.
Also add the ti-st folder to list of drivers under drivers/misc.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wolfram Sang