When porting blktrace to tracepoints, we changed to trace/block.h
for trace prober declarations.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Now that the cciss SCSI error handling routines operate with interrupts
enabled, we no longer need to maintain the list of command completions that
sendcmd() might inadvertantly scoop up, since now it only runs at driver init
time, and there won't be any other commands for it to scoop up. So we
can remove that list and the code that adds to it and processes it.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Change cciss scsi error handling routines to work with interrupts enabled.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Separate the error processing from sendcmd_withirq_core from the code
which retries commands. The rationale for this is that the SCSI error
handling code can then be made to use sendcmd_withirq_core, but avoid
retrying commands.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Factor out code to process target status of completed commands in sendcmd()
and sendcmd_withirq_core(), and fix problem that bad target status was ignored in
sendcmd_withirq_core.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Simplify interfaces of sendcmd() and sendcmd_withirq() so that they
provide only one way to address commands instead of three ways.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Factor the core of sendcmd_withirq out to provide a simpler interface
which provides access to full error information.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add sysfs entries to the cciss driver needed for the dm/multipath tools.
A file for vendor, model, rev, and unique_id is added for each logical
drive under directory /sys/bus/pci/devices/<dev>/ccissX/cXdY. Where X =
the controller (or host) number and Y is the logical drive number.
A link from /sys/bus/pci/devices/<dev>/ccissX/cXdY/block:cciss!cXdY to
/sys/block/cciss!cXdY/device is also created. A bus is created in
/sys/bus/cciss. A link is created from the pci ccissX entry to
/sys/bus/cciss/devices/ccissX. Please consider this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix the SCSI reset error handler to send a working, properly addressed
reset message to the target device and add code to wait for the target
device to become ready by polling it with Test Unit Ready.
The existing reset code was broken in that it didn't bother to set the
8-byte LUN address to anything besides zero, so the command was addressed
to the controller, which pretended to the driver that the command
succeeded, while doing nothing. Ages ago I tested this code, but
unbeknownst to me, my test was flawed, and what I thought was a tape drive
getting reset was actually nothing of the sort. Unfortunately, there is
still lots of Smartarray firmware that doesn't handle doing target resets
right, and this code won't help in those cases, but it also shouldn't make
things worse in those cases than they already are.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Cc: Mike Miller <mikem@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Factor out the core of sendcmd() to provide a simpler interface which
exposes all the error information to the caller and make the original
sendcmd use this new function. Rationale: The SCSI error handling
routines need to send commands with interrupts turned off, but they also
need access to the full error information.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Cc: Mike Miller <mikem@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case. The
sector size will be 4KB but the logical block size will remain
512-bytes. Hence we need to distinguish between the physical block size
and the logical ditto.
This patch renames hardsect_size to logical_block_size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent cleanups, there is no place where low level driver
directly manipulates request fields. This means that the 'hard'
request fields always equal the !hard fields. Convert all
rq->sectors, nr_sectors and current_nr_sectors references to
accessors.
While at it, drop superflous blk_rq_pos() < 0 test in swim.c.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: unsik Kim <donari75@gmail.com>
Cc: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
rq->data_len served two purposes - the length of data buffer on issue
and the residual count on completion. This duality creates some
headaches.
First of all, block layer and low level drivers can't really determine
what rq->data_len contains while a request is executing. It could be
the total request length or it coulde be anything else one of the
lower layers is using to keep track of residual count. This
complicates things because blk_rq_bytes() and thus
[__]blk_end_request_all() relies on rq->data_len for PC commands.
Drivers which want to report residual count should first cache the
total request length, update rq->data_len and then complete the
request with the cached data length.
Secondly, it makes requests default to reporting full residual count,
ie. reporting that no data transfer occurred. The residual count is
an exception not the norm; however, the driver should clear
rq->data_len to zero to signify the normal cases while leaving it
alone means no data transfer occurred at all. This reverse default
behavior complicates code unnecessarily and renders block PC on some
drivers (ide-tape/floppy) unuseable.
This patch adds rq->resid_len which is used only for residual count.
While at it, remove now unnecessasry blk_rq_bytes() caching in
ide_pc_intr() as rq->data_len is not changed anymore.
Boaz : spotted missing conversion in osd
Sergei : spotted too early conversion to blk_rq_bytes() in ide-tape
[ Impact: cleanup residual count handling, report 0 resid by default ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This is the second go through of the old DMA_nBIT_MASK macro,and there're not
so many of them left,so I put them into one patch.I hope this is the last round.
After this the definition of the old DMA_nBIT_MASK macro could be removed.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
loop: mutex already unlocked in loop_clr_fd()
cfq-iosched: don't let idling interfere with plugging
block: remove unused REQ_UNPLUG
cfq-iosched: kill two unused cfqq flags
cfq-iosched: change dispatch logic to deal with single requests at the time
mflash: initial support
cciss: change to discover first memory BAR
cciss: kernel scan thread for MSA2012
cciss: fix residual count for block pc requests
block: fix inconsistency in I/O stat accounting code
block: elevator quiescing helpers
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a method for discovering the first memory BAR. All Smart Array
controllers to date have always had the the memory BAR as the first BAR.
A new controller to be released later this year breaks that model.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The MSA2012 cannot inform the driver of configuration changes since all
management is out of band. This is a departure from any storage we have
supported in the past. We need some way to detect changes on the topology
so we implement this kernel thread. In some instances there's nothing we
can do from the driver (like LUN failure) so just print out a message. In
the case where logical volumes are added or deleted we call
rebuild_lun_table to refresh the driver's view of the world.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We must complete the full request, so store the request count and then set
the ->data_len to the residual count from the hardware.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The hardware requires 64-bit alignment of commands, so add a build bug
check for that. The recent commit 8a3173de4a
didn't change the size of the command, but other additions/changes may and
thus break badly at runtime.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commit 5e4c91c84b forgot to remove the
initial sleep, get rid of it.
Thanks to Randy Dunlap <randy.dunlap@oracle.com> for spotting this error.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
If reset_devices is set for kexec, then cciss will delay 30 seconds
since the old 5i controller _may_ need that long to recover. Replace
the long sleep with incremental sleep and tests to reduce the 30 seconds
to worst case for 5i, so that other controllers will proceed quickly.
Reviewed-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The kexec kernel resets the CCISS hardware in three steps:
1. Use PCI power management states to reset the controller in the
kexec kernel.
2. Clear the MSI/MSI-X bits in PCI configuration space so that MSI
initialization in the kexec kernel doesn't fail.
3. Use the CCISS "No-op" message to determine when the controller
firmware has recovered from the PCI PM reset.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Simplify parameters to deregister_disk function.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This both cleans up the code and also helps detect the spurious case
of a command attempted being removed from a queue it doesn't belong
to.
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix problem that deleting multiple logical drives could cause a panic.
It fixes a panic which can be easily reproduced in the following way: Just
create several "arrays," each with multiple logical drives via hpacucli,
then delete the first array, and it will blow up in deregister_disk(), in
the call to get_host() when it tries to dig the hba pointer out of a NULL
queue pointer.
The problem has been present since my code to make rebuild_lun_table
behave better went in.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix printk format warnings when CCISS_DEBUG is defined.
drivers/block/cciss.c:2856: warning: format '%d' expects type 'int', but argument 2 has type 'long unsigned int'
drivers/block/cciss.c:3205: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
drivers/block/cciss.c:3236: warning: format '%x' expects type 'unsigned int', but argument 2 has type '__u64'
drivers/block/cciss.c:3246: warning: format '%x' expects type 'unsigned int', but argument 2 has type '__u64'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This regression was introduced by commit
6ae5ce8e8d ("cciss: remove redundant code").
This patch fixes a regression where the controller firmware version is not
displayed in procfs. The previous patch would be called anytime something
changed. This will get called only once for each controller.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org> [2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Regression introduced by commit 6ae5ce8e8d
("cciss: remove redundant code").
This patch fixes a broken symlink in sysfs that was introduced by the
above commit. We broke it in 2.6.27-rc on or about 20080804. Some
installers are broken if this symlink does not exist and they may not
detect the logical drives configured on the controller. It does not
require being backported into 2.6.26.x or earlier kernels.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org> [2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for 2 new SAS/SATA controllers.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To keep the size of changesets sane we split the switch by drivers;
to keep the damn thing bisectable we do the following:
1) rename the affected methods, add ones with correct
prototypes, make (few) callers handle both. That's this changeset.
2) for each driver convert to new methods. *ALL* drivers
are converted in this series.
3) kill the old (renamed) methods.
Note that it _is_ a flagday; all in-tree drivers are converted and by the
end of this series no trace of old methods remain. The only reason why
we do that this way is to keep the damn thing bisectable and allow per-driver
debugging if anything goes wrong.
New methods:
open(bdev, mode)
release(disk, mode)
ioctl(bdev, mode, cmd, arg) /* Called without BKL */
compat_ioctl(bdev, mode, cmd, arg)
locked_ioctl(bdev, mode, cmd, arg) /* Called with BKL, legacy */
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression n,d;
@@
(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Bug fix. If SCSI tape support is turned off we get an implicit declaration
of cciss_unregister_scsi error in cciss_remove_one.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch fixes a problem where the logical volume count may go negative.
In some instances if several logical are configured on a controller and all
of them are deleted using the online utilities the volume count in /proc may
go negative with no way get it correct again.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch removes redundant code where ever logical volumes are added or
removed. It adds 3 new functions that are called instead of having the same
code spread throughout the driver. It also removes the cciss_getgeometry
function.
The patch is fairly complex but we haven't figured out how to make it any
simpler and still do everything that needs to be done. Some of the
complexity comes from having to special case booting from cciss. Otherwise
the gendisk doesn't get added in time and the switchroot will fail.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch makes the rebuild_lun_table smart enough to not rip a logical
volume out from under the OS. Without this fix if a customer is running
hpacucli to monitor their storage the driver will blindly remove and re-add
the disks whenever the utility calls the CCISS_REGNEWD ioctl. Unfortunately,
both hpacucli and ACUXE call the ioctl repeatedly. Customers have reported
IO coming to a standstill. Calling the ioctl is the problem, this patch is
the fix.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Return -EFAULT instead of -ENOMEM if copy_from_user() fails.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
curr_queue is a local variable in a for loop, and it's being initialized
at the start of each loop. So any assignment at the end of the loop is
pointless.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes the way we determine the maximum number of outstanding
commands for each controller.
Most Smart Array controllers can support up to 1024 commands, the notable
exceptions are the E200 and E200i.
The next generation of controllers which were just added support a mode of
operation called Zero Memory Raid (ZMR). In this mode they only support
64 outstanding commands. In Full Function Raid (FFR) mode they support
1024.
We have been setting the queue depth by arbitrarily assigning some value
for each controller. We needed a better way to set the queue depth to
avoid lots of annoying "fifo full" messages. So we made the driver a
little smarter. We now read the config table and subtract 4 from the
returned value. The -4 is to allow some room for ioctl calls which are
not tracked the same way as io commands are tracked.
Please consider this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix regression in cciss driver that if no logical drives are configured,
no device nodes at all get created.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the next generation of HP Smart Array SAS/SATA
controllers. Shipping date is late Fall 2008.
Bump the driver version to 3.6.20 to reflect the new hardware support from
patch 1 of this set.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simply replace proc_create and further data assigned with proc_create_data.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Alexey Dobriyan <adobriyan@openvz.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use creation by full path: "driver/foo".
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix race condition between cciss_init_one(), cciss_update_drive_info(),
and cciss_check_queues().
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds the missing include directive <linux/scatterlist.h> to the
cciss.c source file. This was discovered by our release team when building
the kernel for the Alpha architecture.
Errors were found as references to functions 'sg_init_table' and 'sg_page' do
not exist without the include for Alpha.
Signed-off-by: Mike Pagano <mpagano@gentoo.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the #define READ_AHEAD 1024 from the driver and uses the
block layer defaults, instead. We have found that under certain workloads
the setting can cause a disk connected to the e200 controller to go offline.
If the disk hiccups the link may try to downshift but the controller is
never notified that the link successfully completed the renegotiation.
We've also found that performance using the block layer default of 32 pages
was on par with the 1024 setting. We tried setting it to zero at one time
based on info from our firmware guys but that killed performance. Turns out
we were talking about 2 different read ahead settings.
Please consider this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Li Zefan