The nwifi header is padded to 4 bytes. This wasn't
a problem until one tried to (at least) rx 4addr
frames.
This finally allows managed iface to be used in a
bridge.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Makes it easier to determine why some failures
happened.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Implement the get TSF by simply returning 0 so that IBSS
merging is happening. Otherwise, IBSS nodes that have similar
SSID naming won't merge. This is simply fooling the mac80211
that the TSF in the received beacon is higher than the local TSF.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Only one channel is returned - the one currently being used.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some chips, baseband watchdog hangs are more common than others, and
the driver has support for handling them.
Interrupts even after a watchdog hang are also quite common, so there's
not much point in spamming the user's logfiles.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
5/10 MHz channel bandwidth is configured via the PLL clock, instead of
the AR_PHY_MODE register. Using that register is AR93xx specific, and
makes the mode incompatible with earlier chipsets.
In some early versions, these flags were apparently applied at the wrong
point in time and thus did not cause connectivity issues, however now
they are causing problems, as pointed out in this OpenWrt ticket:
https://dev.openwrt.org/ticket/14916
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trivially reduces text size too.
$ size drivers/net/wireless/ath/ath9k/debug.o*
text data bss dec hex filename
34436 2528 5128 42092 a46c drivers/net/wireless/ath/ath9k/debug.o.new
34464 2528 5128 42120 a488 drivers/net/wireless/ath/ath9k/debug.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Number of MAC hangs and stuck beacons were missing
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 handles the actual operations, so ath9k can just indicate
support for this. Based on initial tests, this combination seems to
work fine.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows dynamic changes of bandwidth/nss/smps,
e.g. via ht/vht operation mode change
notification.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware ignores SMPS flags in peer assoc command.
For SMPS to work it is necessary to set peer
parameter after peer assoc command so that tx
chainmask is setup properly.
This should fix packet loss and improve throughput
with stations that have SMPS enabled upon
association.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
I modified Michal's commit c930f744bd ("ath10k: implement channel switching") to return
when vdev_start() fails, but forgot to release conf_mutex.
Found by coccinelle:
>> drivers/net/wireless/ath/ath10k/mac.c:2745:5-11: preceding lock on line 2663
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes a checkpatch warning in ath10k:
drivers/net/wireless/ath/ath10k/mac.c:1636: WARNING: Avoid CamelCase: <regpair->regDmnEnum>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix a checkpatch warning:
drivers/net/wireless/ath/ath10k/debug.h:95: CHECK: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The dtim period sent to FW was 0 because the dtim period
was never set. This caused an incorrect dtim count to be sent in
beacons.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes problems seen with multiple softap clients and reconnecting
softap clients.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is more line with the names of the other members
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3680 has a few registers on other addresses.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After fw caps exchange, print the FW's capabilities.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If wowlan if off mac80211 will stop / start the driver on suspend /
resume. This causes problems on resume since request_firmware is called
from start. Fix this by caching the nv.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some wcnss firmwares the start command can take up to 300ms to
complete. Currently there is a 200ms timeout for SMD command to
complete which causes the start to fail.
Increase the timeout to 500ms. Also improve debug information
regarding SMD command completion time.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Response format is not in the canonical format.
wcn36xx_smd_rsp_status_check cannot be used.
* Save the FW caps in wcn36xx struct for later use.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As result deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case IRQ configuration is unknown possibly enabled MSIs
are left enabled in ath10k_pci_deinit_irq(). This update
fixes the described misbehaviour.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The documentation states that pci_enable_msi_block() returns the number of
requests 'could have been allocated', not 'could allocate'. IOW, MSIs are *not*
enabled if a positive value returned.
kvalo: add commit log based on Alexander's email
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass frames with invalid peer status to upper layer.
Next mac80211 will validate frames and drop if required.
This is required to detect spurious frames and pass
this info to user mode (detect CLASS2 CLASS3 frames from
nonauthenticated/nonassociated stations).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is a workaround for HT-enabled STAs which break the spec
and have no HT capabilities RX mask (no HT RX MCS map).
As per spec, in section 20.3.5 Modulation and coding scheme (MCS),
MCS 0 through 7 are mandatory in 20MHz with 800 ns GI at all STAs.
Firmware asserts if such situation occurs.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of warm reset target need to be suspended.
Suspend function is extented to handle both cases
with disabling interrupts and without disabling interrupts.
Warm target reset requires suspend with all interrupts
disabled.
This patch depends on
ath10k: fix device initialization routine
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Suspend/resume callbacks are not protected by configuration mutex
so adding such protection. Also in order to simplify implemetation
of suspend function wait queue is replaced by completion.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Hardware CUS232 version 2 has some issues with cold
reset that lead to Data Bus Errors or system hangs
in some cases. It's safer to use warm reset when
possible as it shouldn't trigger the
aforementioned issues.
Prefer warm reset over cold reset. However since
warm reset doesn't work after FW crash make sure to
fallback to cold reset when booting up the HW.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was found during testing the nss calculation does not
cover all corner cases. Station could request eq. only MCS8
and MCS9 (nss=2 specific). Next num_rates=2 so the driver
sets nss=(max((2+7)/8, 1))=1. Which is wrong. The in-driver
calculation was introduced prior (commit ddcc347b70
mac80211: fix rx_nss calculation for drivers with hw rc).
Since it's fixed, use mac80211 provided value from now.
End user will experience lower throuhputs than expected
if the nss is wrongly calculated.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This throw a lot of pointless warnings in case of DFS (radar
detection) and PHYERR events from firmware, when firmware may
actually insert more data, than we assume.
Besides of being noisy this debug does not protect or check
anything usefull currently. It was introduced long time ago
while debugging aggregations. So just removing it.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Show message length and expected length. Helps debug
firmware mismatch issues.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds a routine to calculate the median IQ correction
values for AR955x, which is used for outlier detection.
The normal method which is used for all other chips is
bypassed for AR955x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be used for storing data for mutiple
IQ calibration runs, for AR955x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IQ calibration post-processing for AR955x is different
from other chips - instead of just doing it as part
of AGC calibration once, it is triggered 3 times and
a median is determined. This patch adds initial support
for changing the calibration behavior for AR955x.
Also, to simplify things, a helper routine to issue/poll
AGC calibration is used.
For non-AR955x chips, the iqcal_idx (which will be used
in subsequent patches) is set to zero.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect values are programmed in the registers
containing the IQ correction coefficients by the IQ-CAL
post-processing code. Fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ar9003_hw_tx_iq_cal_outlier_detection instead.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In chips like AR955x, the initvals contain the information
whether IQ calibration is to be done in the HW when an
AGC calibration is triggered. Check if IQ-CAL is enabled
in the initvals before flagging 'txiqcal_done' as true.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calibration data is not reused for SoC chips, so
call ar9003_hw_tx_iq_cal_post_proc() with the correct
argument. The 'is_reusable' flag is currently used
only for PC-OEM chips, but it makes things clearer to
specify it explicity.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Buffalo WLI-UV-AG300P is almost the same as Sony UWA-BR100.
Signed-off-by: Masaki TAGAWA <masaki@club.kyutech.ac.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no benefit in retaining the legacy rate control module
in the driver codebase.
It is known to be buggy and has less than optimal performance
in real-world environments compared with minstrel. The only
reason that it was kept when we made the switch to minstrel
as default was that it showed higher throughput numbers in a
clean/ideal environment.
This is no longer the case and minstrel can push ath9k to
the same throughput levels. In TCP, with 3-stream cards, more than
295 Mbps can be obtained in open air, with 2-stream cards,
210 Mbps is easily reached. To test performance issues,
instead of using a broken rate control module, it is better
to use the fixed-rate interface provided by mac80211 anyway.
The ath9k RC has not received any bug fixes in years and is
just bit-rotting away - this patch removes it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
after switch to common fucntions we do not need this memcpy any more.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michal Kazior