Occasionally users want to know what parameters their Broadcom drivers
are running with. For example, a user may want to know if MSI is
disabled.
This patch has been compile tested.
Signed-off-by: James M Leddy <james.leddy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the ethernet driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring GRE tunnel using OVS, tcp stream is distributed over
all RSS queues which may cause TCP reordering. It happens since OVS
uses L2GRE protocol when kernel gre uses IPGRE.
Patch defaults gre tunnel to L2GRE which allows proper RSS for L2GRE
packets and (implicitly) disables RSS for IPGRE traffic.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MII management bus clock is derived from the MAC clock by dividing it by
MIIMODER register CLKDIV field value. This value may need to be set up
in case it is undefined or its default value is too high (and
communication with PHY is too slow) or too low (and communication with
PHY is impossible). The value of CLKDIV is not specified directly, but
is derived from the MAC clock for the default MII management bus frequency
of 2.5MHz. The MAC clock may be specified in the platform data, or in
the 'clocks' device tree attribute.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OpenCores 10/100 Mbps MAC does not support speeds above 100 Mbps, but does
not disable advertisement when PHY supports them. This results in
non-functioning network when the MAC is connected to a gigabit PHY connected
to a gigabit switch.
The fix is to disable gigabit speed advertisement on attached PHY
unconditionally.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX and RX rings share memory and descriptors. Maximal number of
descriptors reported is one less than the total available nuber of
descriptors. For the set operation the requested number of TX descriptors
is rounded down to the nearest power of two (driver logic requirement).
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following methods are implemented:
- get link state (standard implementation);
- get timestamping info (standard implementation).
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the GPIO bitbang MDIO driver is used instead of the Davinci MDIO driver
we need to configure the phy_id string differently. Otherwise this string
looks like this "gpio.6" instead of "gpio-0" and the PHY is not found when
phy_connect() is called.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Several fixups, of note:
1) Fix unlock of not held spinlock in RXRPC code, from Alexey
Khoroshilov.
2) Call pci_disable_device() from the correct shutdown path in bnx2x
driver, from Yuval Mintz.
3) Fix qeth build on s390 for some configurations, from Eugene
Crosser.
4) Cure locking bugs in bond_loadbalance_arp_mon(), from Ding
Tianhong.
5) Must do netif_napi_add() before registering netdevice in sky2
driver, from Stanislaw Gruszka.
6) Fix lost bug fix during merge due to code movement in ieee802154,
noticed and fixed by the eagle eyed Stephen Rothwell.
7) Get rid of resource leak in xen-netfront driver, from Annie Li.
8) Bounds checks in qlcnic driver are off by one, from Manish Chopra.
9) TPROXY can leak sockets when TCP early demux is enabled, fix from
Holger Eitzenberger"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
qeth: fix build of s390 allmodconfig
bonding: fix locking in bond_loadbalance_arp_mon()
tun: add device name(iff) field to proc fdinfo entry
DT: net: davinci_emac: "ti, davinci-no-bd-ram" property is actually optional
DT: net: davinci_emac: "ti, davinci-rmii-en" property is actually optional
bnx2x: Fix generic option settings
net: Fix warning on make htmldocs caused by skbuff.c
llc: remove noisy WARN from llc_mac_hdr_init
qlcnic: Fix loopback test failure
qlcnic: Fix tx timeout.
qlcnic: Fix initialization of vlan list.
qlcnic: Correct off-by-one errors in bounds checks
net: Document promote_secondaries
net: gre: use icmp_hdr() to get inner ip header
i40e: Add missing braces to i40e_dcb_need_reconfig()
xen-netfront: fix resource leak in netfront
net: 6lowpan: fixup for code movement
hyperv: Add support for physically discontinuous receive buffer
sky2: initialize napi before registering device
net: Fix memory leak if TPROXY used with TCP early demux
...
When user tried to change generic options using "ethtool -s" command, while SFP
module is plugged out or during module detection, the command would have failed
with "Unsupported port type" message. The fix is to ignore the port option in
case it's same as the current port configuration.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver was returning from link event handler without
setting linkup variable
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o __qlcnic_down call's netif_tx_disable which in turn stops
all the TX queues, corresponding start queue was missing in
__qlcnic_up which was leading to tx timeout.
o The commit b84caae486
(qlcnic: Fix usage of netif_tx_{wake, stop} api during link change.)
exposed this issue.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Do not re-initialize vlan list in case of adapter reset.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Bound checks should be >= instead of > for number of receive descriptors
and number of receive rings.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc updates from Ben Herrenschmidt:
"So here's my next branch for powerpc. A bit late as I was on vacation
last week. It's mostly the same stuff that was in next already, I
just added two patches today which are the wiring up of lockref for
powerpc, which for some reason fell through the cracks last time and
is trivial.
The highlights are, in addition to a bunch of bug fixes:
- Reworked Machine Check handling on kernels running without a
hypervisor (or acting as a hypervisor). Provides hooks to handle
some errors in real mode such as TLB errors, handle SLB errors,
etc...
- Support for retrieving memory error information from the service
processor on IBM servers running without a hypervisor and routing
them to the memory poison infrastructure.
- _PAGE_NUMA support on server processors
- 32-bit BookE relocatable kernel support
- FSL e6500 hardware tablewalk support
- A bunch of new/revived board support
- FSL e6500 deeper idle states and altivec powerdown support
You'll notice a generic mm change here, it has been acked by the
relevant authorities and is a pre-req for our _PAGE_NUMA support"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (121 commits)
powerpc: Implement arch_spin_is_locked() using arch_spin_value_unlocked()
powerpc: Add support for the optimised lockref implementation
powerpc/powernv: Call OPAL sync before kexec'ing
powerpc/eeh: Escalate error on non-existing PE
powerpc/eeh: Handle multiple EEH errors
powerpc: Fix transactional FP/VMX/VSX unavailable handlers
powerpc: Don't corrupt transactional state when using FP/VMX in kernel
powerpc: Reclaim two unused thread_info flag bits
powerpc: Fix races with irq_work
Move precessing of MCE queued event out from syscall exit path.
pseries/cpuidle: Remove redundant call to ppc64_runlatch_off() in cpu idle routines
powerpc: Make add_system_ram_resources() __init
powerpc: add SATA_MV to ppc64_defconfig
powerpc/powernv: Increase candidate fw image size
powerpc: Add debug checks to catch invalid cpu-to-node mappings
powerpc: Fix the setup of CPU-to-Node mappings during CPU online
powerpc/iommu: Don't detach device without IOMMU group
powerpc/eeh: Hotplug improvement
powerpc/eeh: Call opal_pci_reinit() on powernv for restoring config space
powerpc/eeh: Add restore_config operation
...
Indentation mismatch spotted with Coverity.
Introduced in 4e3b35b044 ("i40e: add DCB and DCBNL support")
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Submission d9aee59 "bnx2x: Don't release PCI bars on shutdown" separated
the PCI remove and shutdown flows, but pci_disable_device() is still
being called on both.
As a result, a dev_WARN_ONCE will be hit during shutdown for every bnx2x
VF probed on a hypervisor (as its shutdown callback will be called and later
pci_disable_sriov() will call its remove callback).
This calls the pci_disable_device() only on the remove flow.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logging the MAC address on every if-up, is not really useful, and annoying when
there is no cable inserted and NetworkManager tries the ifup every 50 seconds.
Also change the log level from warning to info, as that is what it is.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logging a PTP error on hw which simply does not support PTP is not very
useful. Moreover this message gets logged on every if-up, and if there is
no cable inserted NetworkManager will re-try the ifup every 50 seconds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/8390/apne.c: In function ‘apne_probe1’:
drivers/net/ethernet/8390/apne.c:215: warning: unused variable ‘ei_local’
Introduced by commit c45f812f02 ("8390 :
Replace ei_debug with msg_enable/NETIF_MSG_* feature"), which added the
variable without using it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
- Flow steering for InfiniBand UD traffic
- IP-based addressing for IBoE aka RoCE
- Pass SRP submaintainership from Dave to Bart
- SRP transport fixes from Bart
- Add the new Cisco usNIC low-level device driver
- Various other fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=wAWA
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.14:
- Flow steering for InfiniBand UD traffic
- IP-based addressing for IBoE aka RoCE
- Pass SRP submaintainership from Dave to Bart
- SRP transport fixes from Bart
- Add the new Cisco usNIC low-level device driver
- Various other fixes"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (75 commits)
IB/mlx5: Verify reserved fields are cleared
IB/mlx5: Remove old field for create mkey mailbox
IB/mlx5: Abort driver cleanup if teardown hca fails
IB/mlx5: Allow creation of QPs with zero-length work queues
mlx5_core: Fix PowerPC support
mlx5_core: Improve debugfs readability
IB/mlx5: Add support for resize CQ
IB/mlx5: Implement modify CQ
IB/mlx5: Make sure doorbell record is visible before doorbell
mlx5_core: Use mlx5 core style warning
IB/mlx5: Clear out struct before create QP command
mlx5_core: Fix out arg size in access_register command
RDMA/nes: Slight optimization of Ethernet address compare
IB/qib: Fix QP check when looping back to/from QP1
RDMA/cxgb4: Fix gcc warning on 32-bit arch
IB/usnic: Remove unused includes of <linux/version.h>
RDMA/amso1100: Add check if cache memory was allocated before freeing it
IPoIB: Report operstate consistently when brought up without a link
IB/core: Fix unused variable warning
RDMA/cma: Handle global/non-linklocal IPv6 addresses in cma_check_linklocal()
...
The adapter is freed before we check its flags. It was caused
by commit 144be3d ("net/cxgb4: Avoid disabling PCI device for
towice"). The problem was reported by Intel's "0-day" tool.
The patch fixes it to avoid reverting commit 144be3d.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Refactored MSI-x vector calculation for All adapters.
Decoupled logic in the code which was using same call to
request MSI-x vectors in default driver load, as well as
during set_channel() operation for TSS/RSS. This refactoring
simplifies code for TSS/RSS code path as well as probe path
of the driver load for all adapters.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Refactor configuration of interrupt coalescing parameters for
all supported adapters.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for MSI/MSI-X mode in poll controller routine.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Added hardware ops for interrupt enable/disable functions
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Dump each Tx queue details with all descriptors, queue indices
and Tx queue stats to imporve data colletion in situations
where Tx timeout occurs.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Use boolean type instead of u8.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of a workaround for a hardware erratum in the SFC9100 family
(SF bug 35388), the TX_DESC_UPD_DWORD register address is also used
for communicating with the event block, and only descriptor pointer
values < 2048 are valid.
If the TX DMA ring size is increased to 4096 descriptors (which the
firmware still allows) then we may write a descriptor pointer
value >= 2048, which has entirely different and undesirable effects!
Limit the TX DMA ring size correctly when this workaround is in
effect.
Fixes: 8127d661e7 ('sfc: Add support for Solarflare SFC9100 family')
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this situation then ARRAY_SIZE() and sizeof() are the same, but we're
really dealing with array indexes and not byte offsets so ARRAY_SIZE()
is cleaner.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We possibly retrieve the adapter's statistics during EEH recovery
and that should be disallowed. Otherwise, it would possibly incur
replicate EEH error and EEH recovery is going to fail eventually.
The patch reuses statistics lock and checks net_device is attached
before going to retrieve statistics, so that the problem can be
avoided.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have EEH error happens to the adapter and we have to remove
it from the system for some reasons (e.g. more than 5 EEH errors
detected from the device in last hour), the adapter will be disabled
for towice separately by eeh_err_detected() and remove_one(), which
will incur following unexpected backtrace. The patch tries to avoid
it.
WARNING: at drivers/pci/pci.c:1431
CPU: 12 PID: 121 Comm: eehd Not tainted 3.13.0-rc7+ #1
task: c0000001823a3780 ti: c00000018240c000 task.ti: c00000018240c000
NIP: c0000000003c1e40 LR: c0000000003c1e3c CTR: 0000000001764c5c
REGS: c00000018240f470 TRAP: 0700 Not tainted (3.13.0-rc7+)
MSR: 8000000000029032 <SF,EE,ME,IR,DR,RI> CR: 28000024 XER: 00000004
CFAR: c000000000706528 SOFTE: 1
GPR00: c0000000003c1e3c c00000018240f6f0 c0000000010fe1f8 0000000000000035
GPR04: 0000000000000000 0000000000000000 00000000003ae509 0000000000000000
GPR08: 000000000000346f 0000000000000000 0000000000000000 0000000000003fef
GPR12: 0000000028000022 c00000000ec93000 c0000000000c11b0 c000000184ac3e40
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR24: 0000000000000000 c0000000009398d8 c00000000101f9c0 c0000001860ae000
GPR28: c000000182ba0000 00000000000001f0 c0000001860ae6f8 c0000001860ae000
NIP [c0000000003c1e40] .pci_disable_device+0xd0/0xf0
LR [c0000000003c1e3c] .pci_disable_device+0xcc/0xf0
Call Trace:
[c0000000003c1e3c] .pci_disable_device+0xcc/0xf0 (unreliable)
[d0000000073881c4] .remove_one+0x174/0x320 [cxgb4]
[c0000000003c57e0] .pci_device_remove+0x60/0x100
[c00000000046396c] .__device_release_driver+0x9c/0x120
[c000000000463a20] .device_release_driver+0x30/0x60
[c0000000003bcdb4] .pci_stop_bus_device+0x94/0xd0
[c0000000003bcf48] .pci_stop_and_remove_bus_device+0x18/0x30
[c00000000003f548] .pcibios_remove_pci_devices+0xa8/0x140
[c000000000035c00] .eeh_handle_normal_event+0xa0/0x3c0
[c000000000035f50] .eeh_handle_event+0x30/0x2b0
[c0000000000362c4] .eeh_event_handler+0xf4/0x1b0
[c0000000000c12b8] .kthread+0x108/0x130
[c00000000000a168] .ret_from_kernel_thread+0x5c/0x74
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not continue with cleanup flow. If this ever happens we can check which
resources remained open.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
1. Fix derivation of sub-page index from the dma address in free_4k.
2. Fix the DMA address passed to dma_unmap_page by masking it properly.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use strings to display transport service or state of QPs. Use numeric
value for MTU of a QP.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Implement resize CQ which is a mandatory verb in mlx5.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Modify CQ is used by ULPs like IPoIB to change moderation parameters. This
patch adds support in mlx5.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use mlx5_core_warn(), which is the standard warning emitter function, instead
of pr_warn().
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Output structs are expected by firmware to be cleared when a command is called.
Clear the "out" struct instead of "dout" which is used only later.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The output size should be the sum of the core access reg output struct
plus the size of the specific register data provided by the caller.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This is a fix to a regression introduced by commit:
"982290a net/mlx4_core: Check port number for validity
before accessing data"
IPoIB could not attach to multicast group and we get this in dmesg:
[144214.145008] ib0: failed to attach to multicast group, ret = -22
[144214.145016] ib0: couldn't attach QP to multicast group ff12:401b:ffff:0000:0000:0000:ffff:ffff
[144214.145019] ib0: multicast join failed for ff12:401b:ffff:0000:0000:0000:ffff:ffff, status -22
The cause to the problem is because port is extracted from gid[5].
Which is only valid for Ethernet.
Removed this validation in mlx4_qp_attach_common(), which is accessed
from both Ethernet and IB flows.
Error flow for bad port value in Ethernet is already exists in that
function.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current logic to put interface into VLAN Promiscous mode is not correct.
We should increment "adapter->vlans_added" before calling be_vid_config().
Also removed some unwanted log messages.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VF originating from a given PF is flr-ed, that PF gets an interrupt
from the chip management and takes a part in the flr process.
This patch fixes several corner cases in which the driver performs its part
of the flr flow out-of-order, causing the FW to assert due to badly timed
messages received from the driver.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow I transposed these two while bringing the original statistics
support upstream.
Fixes: 99691c4ac1 ('sfc: Add PTP counters to ethtool stats')
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PORT_RESET MC command was NOP in the ef10 firmware hence we are using
ENTITY_RESET to make sure all resource allocations are reset.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull m68k updates from Geert Uytterhoeven:
- Zorro bus cleanups and UAPI revival
- Bootinfo cleanups and UAPI revival
- Kexec support
- Memory size reductions and bug fixes for multi-platform kernels
- Polled interrupt support for Atari EtherNAT, EtherNEC and NetUSBee
- Machine-specific random_get_entropy()
- Defconfig updates and cleanups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: (46 commits)
m68k/mac: Make SCC reset work more reliably
m68k/irq - Use polled IRQ flag for MFP timer cascaded interrupts
m68k: Update defconfigs for v3.13-rc1
m68k/defconfig: Enable EARLY_PRINTK
m68k/mm: kmap spelling/grammar fixes
m68k: Convert arch/m68k/kernel/traps.c to pr_*()
m68k: Convert arch/m68k/mm/fault.c to pr_*()
m68k/mm: Check for mm != NULL in do_page_fault() debug code
m68k/defconfig: Disable /sbin/hotplug fork-bomb by default
m68k/atari: Hide RTC_PORT() macro from rtc-cmos
m68k/amiga,atari: Fix specifying multiple debug= parameters
m68k/defconfig: Use ext4 for ext2/ext3 file systems
m68k: Add support to export bootinfo in procfs
m68k: Add kexec support
m68k/mac: Mark Mac IIsi ADB driver BROKEN
m68k/amiga: Provide mach_random_get_entropy()
m68k: Add infrastructure for machine-specific random_get_entropy()
m68k/atari: Call paging_init() before nf_init()
m68k: Remove superfluous inclusions of <asm/bootinfo.h>
m68k/UAPI: Use proper types (endianness/size) in <asm/bootinfo*.h>
...
When timestamping is enabled, stmmac_tx_clean will call
stmmac_get_tx_hwtstamp to get tx TS.
But the skb can be NULL because the last of its tx_skbuff is NULL
if this packet frame is filled in more than one descriptors.
To fix the issue, change the code:
- Store TX skb to the tx_skbuff[] of frame's last segment.
- Check skb is not NULL in stmmac_get_tx_hwtstamp.
Signed-off-by: Bruce Liu <damuzi000@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Allwinner A20 has an ethernet controller that seems to be
an early version of Synopsys DesignWare MAC 10/100/1000 Universal,
which is supported by the stmmac driver.
Allwinner's GMAC requires setting additional registers in the SoC's
clock control unit.
The exact version of the DWMAC IP that Allwinner uses is unknown,
thus the exact feature set is unknown.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac driver core allows passing feature flags and callbacks via
platform data. Add a similar stmmac_of_data to pass flags and callbacks
tied to compatible strings. This allows us to extend stmmac with glue
layers for different SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The snps,phy-addr device tree property is non-standard, and should be
removed in favor of proper phy node support. Remove it from the binding
documents and warn if the property is still used.
Most PHYs respond to address 0, but a few don't, so auto-detect PHY
address by default, to make up for the lack of explicit address selection.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
"snps,force_sf_dma_mode" is documented in stmmac device tree bindings,
but is never handled by the driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current .init and .exit callbacks requires access to driver
private data structures. This is not a good seperation and abstraction.
Instead, we add a new .setup callback for allocating private data, and
pass the returned pointer to the other callbacks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DWMAC has a reset assert line, which is used on some SoCs. Add an
optional reset control to stmmac driver core.
To support reset control deferred probing, this patch changes the driver
probe function to return the actual error, instead of just -EINVAL.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac driver does not enable the main clock during the probe phase.
If the clock was not enabled by the boot loader or was disabled by the
kernel, hardware features and the MDIO bus would not be probed properly.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch changed prototypes, but forgot functions.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP based RoCE gids don't store Ethernet L2 parameters, MAC and VLAN.
Therefore, we need to extract them from the CQE and place them in
struct ib_wc (to be used for cases were they were taken from the gid).
Also, when modifying a QP or building address handle, instead of
parsing the dgid to get the MAC and VLAN, take them from the address
handle attributes.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
net/ipv4/tcp_metrics.c
Overlapping changes between the "don't create two tcp metrics objects
with the same key" race fix in net and the addition of the destination
address in the lookup key in net-next.
Minor overlapping changes in bnx2x driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
This change merges the ixgbevf_tx_map call and the ixgbevf_tx_queue call
into a single function. In order to make room for this setting of cmd_type
and olinfo flags is done in separate functions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch takes advantage of the dma buffer always being present in the
first descriptor and mapped as single. As such we can call dma_unmap_single
and don't need to check for DMA mapping in ixgbevf_clean_tx_irq().
In addition this patch makes use of the DMA API.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that the first tx_buffer structure acts as a
central storage location for most of the info about the skb we are about
to transmit.
In addition this patch makes tx_flags part of the ixgbevf_tx_buffer struct.
This allows us to use the flags directly from the stucture and as result
removes the tx_flags parameter from some functions. Also as a cleanup
mapped_as_page is folded into tx_flags and some unused flags were removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds counters for tx_restart_queue and tx_timeout_count.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the Tx/Rx counters for checksum offload.
The Tx counter was never updated and the Rx counter is of limited use.
This is in effort to clean up the counters and make them consistent
with the counters shown by ixgbe.
Also this patch removes some members of the adapter structure that were
never used and shuffles others to reduce number of holes.
before:
/* size: 1568, cachelines: 25, members: 48 */
/* sum members: 1519, holes: 10, sum holes: 43 */
/* padding: 6 */
/* last cacheline: 32 bytes */
after:
/* size: 1480, cachelines: 24, members: 43 */
/* sum members: 1479, holes: 1, sum holes: 1 */
/* last cacheline: 8 bytes */
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves hot-path specific statistics into the ring structure.
This allows us to drop the adapter structure in some functions and should
help with performance.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the code by removing the adapter structure as
parameter from multiple functions. The adapter structure was previously
being used to access the dev pointer, but this can also be done via the
ixgbevf_ring structure. This way we can drop the adapter as parameter from
these functions.
This patch also includes small cleanups in some error code paths.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the device ID #defines to follow the _DEV_ID convention
already established in the other Intel drivers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow compiling DCB related files if I40E_DCB option
is supported in the kernel configuration.
DCB is disabled by default.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Tested-By: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds capability to configure DCB on i40e network
interfaces using Intel XL710 adapter firmware APIs.
By default all VSIs are only enabled for the default traffic
class enabled by firmware for any given PF. The driver would
query the firmware for the traffic classes that are enabled for
the port and reconfigure the LAN VSI to match to the port traffic
class settings. All other VSIs are only enabled for the default
traffic class settings for now.
The driver registers and listens to firmware events that may
require change in the DCB settings. It may reconfigure the VSI
settings based on these events.
This patch exposes IEEE DCBNL interfaces for the i40e driver to
allow any application to query the DCB settings on the adapter.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-By: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel XL710 series of adapters support QoS as per the
IEEE 802.1 DCB (Data Center Bridging) standard.
This is supported in conjuction with:
- Enhanced Transmission Selection (ETS) - IEEE 802.1Qaz
- Priority Flow Control (PFC) - IEEE 802.1Qbb
- DCB eXchange Protocol (DCBX) - IEEE 802.1Qaz
On Intel XL710 adapters DCBX is performed by the adapter
firmware. The firmware runs DCBX in willing mode and configures
the port as per the DCB settings recommended by it's link
partner.
By default in absence of any DCBX; firmware would configure the
port with a single traffic class and all of the port bandwith
will be allocated to that traffic class.
This patch adds functions and calls to support querying and
configuring DCB using firmware APIs.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-By: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i40e hardware was generating some inconsistent results
when using current programming methods. This refactor
fixes the inconsistencies that were preventing clean
unloads of the driver, and moves the queues for handling
flow director errors into their own hardware VSI.
This patch also implements a corrected version of the
basic ethtool add ntuple rule, which will disable
the driver's automatic flow programming. A future patch
adds remove/replay/list support for ntuple.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FLAG_FDIR_* defines can be renamed to be more descriptive.
This patch is in preparation for the following where the fdir
code is refactored.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix more whitespace issues, including making some locals declared
in a nicer order.
Also update Copyright string printed when the driver loads.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a workaround that is no longer necessary and implement
a better understanding of what firmware is returning in the MSI-X
vector count. This makes it so that the driver ends up with the
right amount of queues when using all available MSI-X vectors.
Change-ID: I34e60cc71dcfb1b5412f37df956fedcc49ade187
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compile testing with higher warning levels found this complaint:
i40e_nvm.c: warning: 'checksum_local' may be used uninitialized in
this function
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump the version number to better match functionality provided with out of
tree driver of the same version.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump the version number to better match functionality provided with out
of tree driver of the same version.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds braces around the ixgbe_qv_lock_* calls which previously only
had braces around the if portion. Kernel style guidelines for this require
parenthesis around all conditions if they are required around one. In addition
the comment while not illegal C syntax makes the code look wrong at a cursory
glance. This patch corrects the style and adds braces so that the full if-else
block is uniform.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to get correct drop monitor notifications for dropped
packets, we should call kfree_skb() instead of dev_kfree_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 43dc4e01 Limit number of reported VFs to device
specific value It doesn't work and always returns -EBUSY because VFs are
already enabled.
ixgbe_enable_sriov()
pci_enable_sriov()
sriov_enable()
{
... ..
iov->ctrl |= PCI_SRIOV_CTRL_VFE | PCI_SRIOV_CTRL_MSE;
pci_cfg_access_lock(dev);
... ...
}
pci_sriov_set_totalvfs()
{
... ...
if (dev->sriov->ctrl & PCI_SRIOV_CTRL_VFE)
return -EBUSY;
...
}
So should set driver_max_VFs with pci_sriov_set_totalvfs() before
enable VFs with ixgbe_enable_sriov().
V2: revised for net-next tree.
Signed-off-by: Ethan Zhao <ethan.kernel@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because ixgbe driver limit the max number of VF
functions could be enabled to 63, so define one macro IXGBE_MAX_VFS_DRV_LIMIT
and cleanup the const 63 in code.
v3: revised for net-next tree.
Signed-off-by: Ethan Zhao <ethan.kernel@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The r7s72100 SoC includes a fast ethernet controller.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a boolean from sh_eth_is_gether() and refactor it as a one-liner.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove function qlcnic_enable_eswitch which was defined
but never used in current code.
Compile tested only.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions only used in one file should be static.
Found by running make namespacecheck
Compile tested only.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes following sparse warning
davinci_mdio.c:85:27: warning: symbol 'default_pdata' was not declared. Should it be static?
Also makes the default_pdata as a constant.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refinements to cloud support in the Firmware API.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that the descriptors were allocated before trying to dump
them to the logfile. While we're there, de-trick-ify the code
so as to be easier to read and not abusing the types and unions.
Change-ID: I22898f4b22cecda3582d4d9e4018da9cd540f177
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ever since this driver was merged the following code was included:
if (skb->len < MISR)
skb->len = MISR;
MISR is defined to 0x3C which is also equivalent to ETH_ZLEN, but use
ETH_ZLEN directly which is exactly what we want to be checking for.
Reported-by: Marc Volovic <marcv@ezchip.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On newer and faster machines (Vortex X86DX) using the r6040 driver, it
was noticed that the driver was returning an error during probing traced
down to being the MDIO bus probing and the inability to complete a MDIO
read operation in time. It turns out that the MDIO operations on these
faster machines usually complete after ~2140 iterations which is bigger
than 2048 (MAC_DEF_TIMEOUT) and results in spurious timeouts depending
on the system load.
Update r6040_phy_read() and r6040_phy_write() to include a 1
micro second delay in each busy-looping iteration of the loop which is a
much safer operation than incrementing MAC_DEF_TIMEOUT.
Reported-by: Nils Koehler <nils.koehler@ibt-interfaces.de>
Reported-by: Daniel Goertzen <daniel.goertzen@gmail.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused function vxge_hw_vpath_vid_get
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 'make namespacecheck' to code that could be declared static.
After that remove code that is not being used.
Compile tested only.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
James M Leddy