New codec ALC255/ALC3234 support multifunction jacks.
It used for menual select the input device.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [8fe7b65ab465: ALSA: hda - Apply GPIO setup for MacBooks
with CS4208] added a fixup entry matching with the vendor id 0x106b.
This broke the fixups for previous MBA6,1 and 6,2, since the PCI SSID
vendor id matches before evaluating the codec SSIDs.
We had a similar issue on Mac with Sigmatel codecs, and solve this
problem again similarly, by introducing a skeleton entry matching with
the all MacBooks, then remap to the right one.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64401
Fixes: 8fe7b65ab4 ('ALSA: hda - Apply GPIO setup for MacBooks with CS4208')
Cc: <stable@vger.kernel.org> [v3.12+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Upon suspend / resume, the fixup register settings are lost because
sending HDA_FIXUP_ACT_PRE_PROBE is not part of the resume path. Instead,
write our registers in response to the HDA_FIXUP_ACT_INIT, which happens
after initial probe and upon resume.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
dmesg here has a 100+ consecutive lines of:
[ 1464.219446] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
[ 1464.219451] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
[ 1464.219454] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
...
Ratelimit the message to reduce the dmesg log noise.
Coalesce the format while at it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the recent fake ELD patches, we can remove the check for AMD
HDMI in hdmi_present_sense() and decide the return value from
eld_valid value.
Suggested by Anssi Hannula.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just added a missing ifdef:
sound/pci/ice1712/quartet.c:210:14: warning: 'get_binary' defined but not used [-Wunused-function]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This fixes a race condition in case several monitors are being
repolled in parallel.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the jack should not be reported to userspace (e g, because it is
in some transitional state), one can set this flag.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is a small gap between the jack detection unsolicited event and
the time the ELD is updated. When user-space queries the HDMI ELD
immediately after receiving the notification, it might fail because of
this gap.
For avoiding such a problem, this patch tries to delay the HDMI jack
detect notification until ELD information is fully updated. The
workaround is imperfect, but good enough as a starting point.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This machine has a multi-function headset jack.
BugLink: https://bugs.launchpad.net/bugs/1248856
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS on ASUS W5A laptop with ALC880 codec doesn't provide any pin
configurations, so we have to set up all pins manually.
Reported-and-tested-by: nb <nb@dagami.org>
Cc: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's a superset of the existing CX2075x codecs, so we can reuse the
existing parser code.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The warnings are really harmless but annoying. Since they are only
about debug prints, and it's at most 32bit DMA, let's just cast to
unsigned long.
sound/pci/lx6464es/lx6464es.c:457:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
sound/pci/lx6464es/lx_core.c:1195:21: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This machine has a mute LED as well as a noisy internal mic. Hence it needs
quirks for both limiting the mic boost as well as enabling the LED.
BugLink: https://bugs.launchpad.net/bugs/1248476
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some HP machines with Realtek codecs have mute LEDs connected to VREF pins.
However when these go into runtime suspend, the pin powers down and its
pin control is disabled, thus disabling the LED too.
This patch fixes that issue by making sure that the pin stays in D0 with
correct pin control.
Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/1248465
Tested-by: Franz Hsieh <franz.hsieh@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BUG_ON() is rather useless for debugging as it leads to panic().
Use WARN_ON() and handle the error cases accordingly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The playback chmap for multi-channel stream hasn't been properly added
to intel8x0 devices due to the wrong condition.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"HDA Intel MID" is no correct name for Haswell HDMI controllers.
Give them a better name, "HDA Intel HDMI".
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Haswell HDMI audio controllers seem to get stuck when unaligned buffer
size is used. Let's enable the buffer alignment for the corresponding
entries.
Since AZX_DCAPS_INTEL_PCH contains AZX_DCAPS_BUFSIZE that disables the
buffer alignment forcibly, define AZX_DCAPS_INTEL_HASWELL and put the
necessary AZX_DCAPS bits there.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60769
Reported-by: Alexander E. Patrakov <patrakov@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Same as we already have for Conexant. Right now it's only enabled
for one machine.
Tested-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device IDs of the AMD Cypress/Juniper/Redwood/Cedar/Cayman/Antilles/
Barts/Turks/Caicos HDMI HDA controllers weren't added explicitly
because the generic entry works, but it made the device appearing as
"Generic", and people are confused as if it's no proper HDMI
controller. Add them so that the name shows up properly as "ATI HDMI"
instead of "Generic".
According to Takashi's tests and the lack of complaints, these devices
work fine without disabling snooping.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a bitmask to hda_gen_spec indicating NIDs to exclude from the
possible volume controls. That is, when the bit is set, the NID
corresponding to the bit won't be picked as an output volume control
any longer.
Basically this is just a band-aid for working around the issue found
with CS4208 codec, where only the headphone pin has a volume AMP with
different dB steps.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60811
Cc: <stable@vger.kernel.org> [v3.12+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check the TLV db scale result before actually dividing in vmaster
slave init code. Also mask TLV_DB_SCALE_MUTE bit so that the right
value is obtained even if this bit is set by the codec driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS on Acer TravelMate 6293 doesn't set up the SPDIF output pin
correctly as default, so enable it via a fixup entry.
Reported-and-tested-by: Hagen Heiduck <heiduck.suse@fmail.postpro.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the HD Audio Device IDs for the Intel Wildcat Point-LP PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function name not_share_unassigned_cvt() is opposite to what it does.
This patch renames it to intel_not_share_assigned_cvt(), and addes comments
to explain why some Intel display codecs need this workaround.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
NVIDIA HDMI codecs do not seem to follow the Audio Sample Packet (ASP)
channel mapping (as set by verb F32h per HDA specification 7.3.3.41)
when playing back 2-channel audio (CEA CA 0x00).
Basically this means that specifying swapped channels for stereo audio
(FR,FL) does not take effect, and e.g. this command plays back on the
wrong channel:
speaker-test -c2 -Dhdmi:CARD=NVidia,DEV=0 -m FR,FL -s1
Multichannel audio is not affected.
This issue has been confirmed to exist on codec 0x10de0015 by me and on
0x10de0040 by Juho Teperi.
Disable 2ch FL/FR channel swapping on all NVIDIA HDMI codecs that use
the standard HDA channel mapping system. Since this is a very minor
functionality loss, we err on the side of disabling it for newer codecs
as well until any future testing confirms that this issue has been
fixed.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Helped-by: Juho Teperi <juho.teperi@iki.fi>
Cc: Aaron Plattner <aplattner@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Valleyview display codec, if an unused pin chooses an assgined converter
selected by a used pin, playback on the unused pin can also give sound to the
output device of the used pin. It's because data flows from the same convertor
to the display port of the used pin. This issue is same as Haswell.
So this patch avoids using assinged convertors for unused pins.
The related function haswell_config_cvts() is renamed for code reuse.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS N56VZ and N76VZ laptops have a bass speaker but its output comes
only from the right channel. This patch adds the extra chmap specific
to these models.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=846531
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS N76VZ needs the same fixup as N56VZ for supporting the boost
speaker.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=846529
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC283-based Chromebook suffers from occasional white noise, and it
turned out that this comes from AA-loopback. Disable this output path
by just clearing mixer_nid, then the generic parser will skip the
creation of AA-loopback path.
Reported-and-tested-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The FUNCTION_TYPE parameter isn't associated with any NID, thus
showing the uninitialized nid in the error message is simply
nonsense.
Spotted by coverity CID 145068.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just pass the error code returned from copy_from_user_toio() and
copy_to_user_fromio() helpers.
Spotted by coverity CID 114119.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The variable runtime is never used, and this might be even a source of
NULL-dereference. Nothing better than killing it.
Spotted by coverity CID 100862.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a possible NULL access of indexp in fill_audio_out_name() called
from snd_hda_get_pin_label().
Spotted by coverity CID 402035.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As EAPD on NID 0x12 (speaker pin) is used as the master amp on
Thinkpads with AD1984A codec, we can hook this to vmaster for saving a
bit more power at master mute state.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AD1984A codec has a couple of pins with EAPD controls, and the generic
codec driver tries to turn each of them on/off depending on the pin
active state. However, Thinkpads seem to use EAPD of the speaker pin
as a master EAPD for controlling the mute of all outputs, including
the headphone. This results in the dead headphone output via the
headphone plugging because it mutes the speaker and turns off EAPD.
The fix is to simply add spec->gen.keep_on_eapd flag.
[This is a regression fix on 3.12 where we moved the AD codec parser
to the generic parser. 3.11 and earlier didn't show this problem
because still static quirks have been used.]
Reported-and-tested-by: Vito Caputo <vcaputo@gnugeneration.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The generic parser has a support of vmaster hook, but this is
initialized only in the init callback with the check of the presence
of the corresponding kctl. However, since kctl is NULL at the very
first init callback that is called before build_controls callback, the
vmaster hook sync is skipped there. Eventually this leads to the
uninitialized state depending on the hook implementation.
This patch adds a simple workaround, just calling the sync function
explicitly at build_controls callback.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Further work on the dmaengine helpers, including support for
configuring the parameters for DMA by reading the capabilities of the
DMA controller which removes some guesswork and magic numbers fromm
drivers.
- A refresh of the documentation.
- Conversions of many drivers to direct regmap API usage in order to
allow the ASoC level register I/O code to be removed, this will
hopefully be completed by v3.14.
- Support for using async register I/O in DAPM, reducing the time taken
to implement power transitions on systems that support it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSajLdAAoJELSic+t+oim9MVEQAJ3t7df5K9R/OynjhKiEFxpP
cBWo306CegZ5oO17UqG+SReJkOWgUI8zIUkNC818suTjtgyhv4WUBx1QgXG8akO5
arHZEQGyReLxgWbnO5ScP7BJt5ZYldfQWN+NPnNlzwvVA8R4xChvAwuHL+kUSSYW
DrOb0ag/Gtn2jQo3o9GbZb5c3UhZqoMg/pQSoVtnvG/O8N/xR0yoeXGsdJv1su6g
OKhCJTRWU8v3FONatR2wWXnSrCBOeJ2Ec7YUJil1FQQdENYZfV3AOsFHxmqsyG2O
Xj2P7CioY0JY7dtFcKjrXgsnjvgZmVdVsdegTJPWS9RjunjyupvSyhMhZYkoA60j
V7RxyIbHAx7hILQqCYYhlOczYHom4MSwAGGt7y7T3oKt0432RvIjE2fP7sTGaqD8
wzuVYuVl4km03xX9g9abF6xjyDE6e+4wun+d8kSvOosvd/nF47gkXUXEvPZh0Ley
013e5fHNDaNF4uaSVXE169JyVxVnHP6nXJDRWZakXsryGXGUpn0quIzobf6fb6XE
fY5Q3QoyP5rHdSMIvGN5Gi76KsHF5CWILWqcWLEVPLnaf9gJmrp3IypmF1c8i7VE
CrcTim5mhNePEX56skRaHhpYHmsxYApSAzxNAA/t3cJ2rtwb87jMM4jOcjHi/war
emSVe5lXkcwv/lU/Pa0N
=rVsK
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.13
- Further work on the dmaengine helpers, including support for
configuring the parameters for DMA by reading the capabilities of the
DMA controller which removes some guesswork and magic numbers fromm
drivers.
- A refresh of the documentation.
- Conversions of many drivers to direct regmap API usage in order to
allow the ASoC level register I/O code to be removed, this will
hopefully be completed by v3.14.
- Support for using async register I/O in DAPM, reducing the time taken
to implement power transitions on systems that support it.
hdmi_setup_audio_infoframe() does not set up pin and infoframe if there
is no connected sink. If a sink is connected while audio playback is
already in progress, the pin and infoframe will not be properly set up,
causing no audio or wrongly mapped audio.
On Intel Haswell codecs the hdmi_setup_audio_infoframe() is already
called again from hdmi_present_sense() when an ELD appears because
transcoder:port mapping may have changed.
Make the call non-Haswell-specific so that audio will be properly set up
if the playback was started before a sink was connected.
Tested on non-Haswell Intel HDMI codec by plugging sink in during
playback.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recent AMD HDMI codecs (revision ID 3 and later, 0x100300 as reported by
procfs codec#0) have a configurable ramp-up/down functionality.
The documentation ( http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf )
specifies that 180 ("180/256 =~ 0.7") is recommended for PCM and 0 for
non-PCM.
Apply the recommended values according to provided S/PDIF AES0 settings
since ramp-up/down does not make sense for non-PCM.
v2: adapted to hdmi_ops infrastructure
* More note from Anssi:
actually, re-reading mails reveals that Olivier didn't find the
expected difference with this setting, except for "maybe slightly
slower startup with AES0=6" (i.e. value 0, which is unexpected).
So maybe
a) it makes too unnoticiable a difference, or
b) only affects certain hardware (card and/or sink), or
c) ramp-up/down is only triggered with the MUTE bit of
ATI_VERB_SET_MULTICHANNEL_xx which is also rev3+ specific,
but is not presently used by the driver,
or something else.
So there's a significant chance setting ramp rate is useless for us ATM,
but probably does not do actual harm either.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Olivier Langlois <olivier@trillion01.com> # v1
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kailang Yang