Currently on both paths of message transmission and reception, the
read lock of tipc_net_lock must be held before bearer is accessed,
while the write lock of tipc_net_lock has to be taken before bearer
is configured. Although it can ensure that bearer is always valid on
the two data paths, link and bearer is closely bound together.
So as the part of effort of removing tipc_net_lock, the locking
policy of bearer protection will be adjusted as below: on the two
data paths, RCU is used, and on the configuration path of bearer,
RTNL lock is applied.
Now RCU just covers the path of message reception. To make it possible
to protect the path of message transmission with RCU, link should not
use its stored bearer pointer to access bearer, but it should use the
bearer identity of its attached bearer as index to get bearer instance
from bearer_list array, which can help us decouple the relationship
between bearer and link. As a result, bearer on the path of message
transmission can be safely protected by RCU when we access bearer_list
array within RCU lock protection.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert bearer_list to RCU list. It's protected by RTNL lock on
update side, and RCU read lock is applied to read side.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hardware address of a underlying netdevice is changed, it is
not enough to simply reset the bearer/links over this device. We
also need to reflect this change in the TIPC bearer and node
discovery structures aswell.
This patch adds the necessary reinitialization of the node disovery
mechanism following a hardware address change so that the correct
originating media address is advertised in the discovery messages.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reported-by: Dong Liu <dliu.cn@gmail.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the allocation of tipc_bearer structure instance is converted
from statical way to dynamical way, we identify whether a certain
tipc_bearer structure pointer is valid by checking whether the pointer
is NULL or not. So the active flag in tipc_bearer structure becomes
redundant.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the effort to introduce RCU protection for the bearer
list, we first need to change it to a list of pointers.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the earlier commits ("tipc: remove 'links' list from
tipc_bearer struct") and ("tipc: introduce new spinlock to protect
struct link_req"), there is no longer any need to protect struct
link_req or or any link list by use of bearer_lock. Furthermore,
we have eliminated the need for using bearer_lock during downcalls
(send) from the link to the bearer, since we have ensured that
bearers always have a longer life cycle that their associated links,
and always contain valid data.
So, the only need now for a lock protecting bearers is for guaranteeing
consistency of the bearer list itself. For this, it is sufficient, at
least for the time being, to continue applying 'net_lock´ in write mode.
By removing bearer_lock we also pre-empt introduction of issue b) descibed
in the previous commit "tipc: remove 'links' list from tipc_bearer struct":
"b) When the outer protection from net_lock is gone, taking
bearer_lock and node_lock in opposite order of method 1) and 2)
will become an obvious deadlock hazard".
Therefore, we now eliminate the bearer_lock spinlock.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In our ongoing effort to simplify the TIPC locking structure,
we see a need to remove the linked list for tipc_links
in the bearer. This can be explained as follows.
Currently, we have three different ways to access a link,
via three different lists/tables:
1: Via a node hash table:
Used by the time-critical outgoing/incoming data paths.
(e.g. link_send_sections_fast() and tipc_recv_msg() ):
grab net_lock(read)
find node from node hash table
grab node_lock
select link
grab bearer_lock
send_msg()
release bearer_lock
release node lock
release net_lock
2: Via a global linked list for nodes:
Used by configuration commands (link_cmd_set_value())
grab net_lock(read)
find node and link from global node list (using link name)
grab node_lock
update link
release node lock
release net_lock
(Same locking order as above. No problem.)
3: Via the bearer's linked link list:
Used by notifications from interface (e.g. tipc_disable_bearer() )
grab net_lock(write)
grab bearer_lock
get link ptr from bearer's link list
get node from link
grab node_lock
delete link
release node lock
release bearer_lock
release net_lock
(Different order from above, but works because we grab the
outer net_lock in write mode first, excluding all other access.)
The first major goal in our simplification effort is to get rid
of the "big" net_lock, replacing it with rcu-locks when accessing
the node list and node hash array. This will come in a later patch
series.
But to get there we first need to rewrite access methods ##2 and 3,
since removal of net_lock would introduce three major problems:
a) In access method #2, we access the link before taking the
protecting node_lock. This will not work once net_lock is gone,
so we will have to change the access order. We will deal with
this in a later commit in this series, "tipc: add node lock
protection to link found by link_find_link()".
b) When the outer protection from net_lock is gone, taking
bearer_lock and node_lock in opposite order of method 1) and 2)
will become an obvious deadlock hazard. This is fixed in the
commit ("tipc: remove bearer_lock from tipc_bearer struct")
later in this series.
c) Similar to what is described in problem a), access method #3
starts with using a link pointer that is unprotected by node_lock,
in order to via that pointer find the correct node struct and
lock it. Before we remove net_lock, this access order must be
altered. This is what we do with this commit.
We can avoid introducing problem problem c) by even here using the
global node list to find the node, before accessing its links. When
we loop though the node list we use the own bearer identity as search
criteria, thus easily finding the links that are associated to the
resetting/disabling bearer. It should be noted that although this
method is somewhat slower than the current list traversal, it is in
no way time critical. This is only about resetting or deleting links,
something that must be considered relatively infrequent events.
As a bonus, we can get rid of the mutual pointers between links and
bearers. After this commit, pointer dependency go in one direction
only: from the link to the bearer.
This commit pre-empts introduction of problem c) as described above.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functionality related to link addition and failover is unnecessarily
hard to understand and maintain. We try to improve this by renaming
some of the functions, at the same time adding or improving the
explanatory comments around them. Names such as "tipc_rcv()" etc. also
align better with what is used in other networking components.
The changes in this commit are purely cosmetic, no functional changes
are made.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove dead code;
tipc_bearer_find_interface
tipc_node_redundant_links
This may break out of tree version of TIPC if there still is one.
But that maybe a good thing :-)
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently TIPC supports two L2 media types, Ethernet and Infiniband.
Because both these media are accessed through the common net_device API,
several functions in the two media adaptation files turn out to be
fully or almost identical, leading to unnecessary code duplication.
In this commit we extract this common code from the two media files
and move them to the generic bearer.c. Additionally, we change
the function names to reflect their real role: to access L2 media,
irrespective of type.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Cc: Patrick McHardy <kaber@trash.net>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, registering a TIPC stack handler in the network device layer
is done twice, once for Ethernet (eth_media) and Infiniband (ib_media)
repectively. But, as this registration is not media specific, we can
avoid some code duplication by moving the registering function to
the generic bearer layer, to the file bearer.c, and call it only once.
The same is true for the network device event notifier.
As a side effect, the two workqueues we are using for for setting up/
cleaning up media can now be eliminated. Furthermore, the array for
storing the specific media type structs, media_array[], can be entirely
deleted.
Note that the eth_started and ib_started flags were removed during the
code relocation. There is now only one call to bearer_setup and
bearer_cleanup, and these can logically not race against each other.
Despite its size, this cleanup work incurs no functional changes in TIPC.
In particular, it should be noted that the sequence ordering of received
packets is unaffected by this change, since packet reception never was
subject to any work queue handling in the first place.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC is currently using the field 'af_packet_priv' in struct net_device
as a handle to find the bearer instance associated to the given network
device. But, by doing so it is blocking other networking cleanups, such
as the one discussed here:
http://patchwork.ozlabs.org/patch/178044/
This commit removes this usage from TIPC. Instead, we introduce a new
field, 'tipc_ptr', to the net_device structure, to serve this purpose.
When TIPC bearer is enabled, the bearer object is associated to
'tipc_ptr'. When a TIPC packet arrives in the recv_msg() upcall
from a networking device, the bearer object can now be obtained from
'tipc_ptr'. When a bearer is disabled, the bearer object is detached
from its underlying network device by setting 'tipc_ptr' to NULL.
Additionally, an RCU lock is used to protect the new pointer.
Henceforth, the existing tipc_net_lock is used in write mode to
serialize write accesses to this pointer, while the new RCU lock is
applied on the read side to ensure that the pointer is 100% valid
within its wrapped area for all readers.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Cc: Patrick McHardy <kaber@trash.net>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct 'tipc_media' represents the specific info that the media
layer adaptors (eth_media and ib_media) expose to the generic
bearer layer. We clarify this by improved commenting, and by giving
the 'media_list' array the more appropriate name 'media_info_array'.
There are no functional changes in this commit.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Communication media types are abstracted through the struct 'tipc_media',
one per media type. These structs are allocated statically inside their
respective media file.
Furthermore, in order to be able to reach all instances from a central
location, we keep a static array with pointers to these structs. This
array is currently initialized at runtime, under protection of
tipc_net_lock. However, since the contents of the array itself never
changes after initialization, we can just as well initialize it at
compile time and make it 'const', at the same time making it obvious
that no lock protection is needed here.
This commit makes the array constant and removes the redundant lock
protection.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct 'tipc_bearer' is a generic representation of the underlying
media type, and exists in a one-to-one relationship to each interface
TIPC is using. The struct contains a 'blocked' flag that mirrors the
operational and execution state of the represented interface, and is
updated through notification calls from the latter. The users of
tipc_bearer are checking this flag before each attempt to send a
packet via the interface.
This state mirroring serves no purpose in the current code base. TIPC
links will not discover a media failure any faster through this
mechanism, and in reality the flag only adds overhead at packet
sending and reception.
Furthermore, the fact that the flag needs to be protected by a spinlock
aggregated into tipc_bearer has turned out to cause a serious and
completely unnecessary deadlock problem.
CPU0 CPU1
---- ----
Time 0: bearer_disable() link_timeout()
Time 1: spin_lock_bh(&b_ptr->lock) tipc_link_push_queue()
Time 2: tipc_link_delete() tipc_bearer_blocked(b_ptr)
Time 3: k_cancel_timer(&req->timer) spin_lock_bh(&b_ptr->lock)
Time 4: del_timer_sync(&req->timer)
I.e., del_timer_sync() on CPU0 never returns, because the timer handler
on CPU1 is waiting for the bearer lock.
We eliminate the 'blocked' flag from struct tipc_bearer, along with all
tests on this flag. This not only resolves the deadlock, but also
simplifies and speeds up the data path execution of TIPC. It also fits
well into our ongoing effort to make the locking policy simpler and
more manageable.
An effect of this change is that we can get rid of functions such as
tipc_bearer_blocked(), tipc_continue() and tipc_block_bearer().
We replace the latter with a new function, tipc_reset_bearer(), which
resets all links associated to the bearer immediately after an
interface goes down.
A user might notice one slight change in link behaviour after this
change. When an interface goes down, (e.g. through a NETDEV_DOWN
event) all attached links will be reset immediately, instead of
leaving it to each link to detect the failure through a timer-driven
mechanism. We consider this an improvement, and see no obvious risks
with the new behavior.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <Paul.Gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_block_bearer() currently takes a bearer name (const char*)
as argument. This requires the function to make a lookup to find
the pointer to the corresponding bearer struct. In the current
code base this is not necessary, since the only two callers
(tipc_continue(),recv_notification()) already have validated
copies of this pointer, and hence can pass it directly in the
function call.
We change tipc_block_bearer() to directly take struct tipc_bearer*
as argument instead.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC 'bearer' exists as an abstract concept, while 'media'
is deemed a specific implementation of a bearer, such as Ethernet
or Infiniband media. When a component inside TIPC wants to control
a specific media, it only needs to access the generic bearer API
to achieve this. However, in the current media implementations,
the 'bearer' name is also extensively used in media specific
function and variable names.
This may create confusion, so we choose to replace the term 'bearer'
with 'media' in all function names, variable names, and prefixes
where this is what really is meant.
Note that this change is cosmetic only, and no runtime behaviour
changes are made here.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add InfiniBand media type based on the ethernet media type.
The only real difference is that in case of InfiniBand, we need the entire
20 bytes of space reserved for media addresses, so the TIPC media type ID is
not explicitly stored in the packet payload.
Sample output of tipc-config:
# tipc-config -v -addr -netid -nt=all -p -m -b -n -ls
node address: <10.1.4>
current network id: 4711
Type Lower Upper Port Identity Publication Scope
0 167776257 167776257 <10.1.1:1855512577> 1855512578 cluster
167776260 167776260 <10.1.4:1216454657> 1216454658 zone
1 1 1 <10.1.4:1216479235> 1216479236 node
Ports:
1216479235: bound to {1,1}
1216454657: bound to {0,167776260}
Media:
eth
ib
Bearers:
ib:ib0
Nodes known:
<10.1.1>: up
Link <broadcast-link>
Window:20 packets
RX packets:0 fragments:0/0 bundles:0/0
TX packets:0 fragments:0/0 bundles:0/0
RX naks:0 defs:0 dups:0
TX naks:0 acks:0 dups:0
Congestion bearer:0 link:0 Send queue max:0 avg:0
Link <10.1.4:ib0-10.1.1:ib0>
ACTIVE MTU:2044 Priority:10 Tolerance:1500 ms Window:50 packets
RX packets:80 fragments:0/0 bundles:0/0
TX packets:40 fragments:0/0 bundles:0/0
TX profile sample:22 packets average:54 octets
0-64:100% -256:0% -1024:0% -4096:0% -16384:0% -32768:0% -66000:0%
RX states:410 probes:213 naks:0 defs:0 dups:0
TX states:410 probes:197 naks:0 acks:0 dups:0
Congestion bearer:0 link:0 Send queue max:1 avg:0
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some network protocols, like InfiniBand, don't have a fixed broadcast
address but one that depends on the configuration. Move the bcast_addr
to struct tipc_bearer and initialize it with the broadcast address of
the network device when the bearer is enabled.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently at the TIPC bearer layer there is the following congestion
mechanism:
Once sending packets has failed via that bearer, the bearer will be
flagged as being in congested state at once. During bearer congestion,
all packets arriving at link will be queued on the link's outgoing
buffer. When we detect that the state of bearer congestion has
relaxed (e.g. some packets are received from the bearer) we will try
our best to push all packets in the link's outgoing buffer until the
buffer is empty, or until the bearer is congested again.
However, in fact the TIPC bearer never receives any feedback from the
device layer whether a send was successful or not, so it must always
assume it was successful. Therefore, the bearer congestion mechanism
as it exists currently is of no value.
But the bearer blocking state is still useful for us. For example,
when the physical media goes down/up, we need to change the state of
the links bound to the bearer. So the code maintaing the state
information is not removed.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The tipc_printf is renamed to tipc_snprintf, as the new name
describes more what the function actually does. It is also
changed to take a buffer and length parameter and return
number of characters written to the buffer. All callers of
this function that used to pass a print_buf are updated.
Final removal of the struct print_buf itself will be done
synchronously with the pending removal of the deprecated
logging code that also was using it.
Functions that build up a response message with a list of
ports, nametable contents etc. are changed to return the number
of characters written to the output buffer. This information
was previously hidden in a field of the print_buf struct, and
the number of chars written was fetched with a call to
tipc_printbuf_validate. This function is removed since it
is no longer referenced nor needed.
A generic max size ULTRA_STRING_MAX_LEN is defined, named
in keeping with the existing TIPC_TLV_ULTRA_STRING, and the
various definitions in port, link and nametable code that
largely duplicated this information are removed. This means
that amount of link statistics that can be returned is now
increased from 2k to 32k.
The buffer overflow check is now done just before the reply
message is passed over netlink or TIPC to a remote node and
the message indicating a truncated buffer is changed to a less
dramatic one (less CAPS), placed at the end of the message.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the comment blocks are floating in limbo between two
functions, or between blocks of code. Delete the extra line
feeds between any comment and its associated following block
of code, to be consistent with the majority of the rest of
the kernel. Also delete trailing newlines at EOF and fix
a couple trivial typos in existing comments.
This is a 100% cosmetic change with no runtime impact. We get
rid of over 500 lines of non-code, and being blank line deletes,
they won't even show up as noise in git blame.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The addition of the "s" to indicate pluralization is intentional,
since the struct actually contains two name variants.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Give it a meaningful prefix, as suggested by DaveM, so that it
is consistent with things like struct tipc_bearer, and so it isn't
confused with anything else. This has no impact on the actual
runtime code behaviour.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Permits run-time alteration of default link settings on a per-media
and per-bearer basis, in addition to the existing per-link basis.
The following syntax can now be used:
tipc-config -lt=<link-name|bearer-name|media-name>/<tolerance>
tipc-config -lp=<link-name|bearer-name|media-name>/<priority>
tipc-config -lw=<link-name|bearer-name|media-name>/<window>
Note that changes to the default settings for a given media type has
no effect on the default settings used by existing bearers. Similarly,
changes to default bearer settings has no effect on existing link
endpoints that utilize that interface.
Thanks to Florian Westphal <fw@strlen.de> for his contributions to
the development of this enhancement.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reworks TIPC's media address data structure and associated processing
routines to transfer all media-specific details of address conversion
to the associated TIPC media adaptation code. TIPC's generic bearer code
now only needs to know which media type an address is associated with
and whether or not it is a broadcast address, and totally ignores the
"value" field that contains the actual media-specific addressing info.
These changes eliminate the need for a number of endianness conversion
operations and will make it easier for TIPC to support new media types
in the future.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Enhances TIPC's Ethernet media support to provide 3 new address conversion
routines, which allow TIPC to interpret an address that is in string form
and to convert an address to and from the 20 byte format used in TIPC's
neighbor discovery messages.
These routines are pre-requisites to a follow on commit that hides all
media-specific addressing details from TIPC's generic bearer code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Enhances conversion of a media address to printable form so that an
unconvertable address will be displayed as a string of hex digits,
rather than not being displayed at all. (Also removes a pointless check
for the existence of the media-specific address conversion routine,
since the routine is not optional.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Speeds up the registration of TIPC media types by passing in a structure
containing the required information, rather than by passing in the various
fields describing the media type individually.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reduces the number of bearers a node can support to 2, which can use
identical or non-identical media. This change won't impact users,
since they are currently limited to a maximum of 2 Ethernet bearers,
and will save memory by eliminating a number of unused entries in
TIPC's media and bearer arrays.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Gets rid of counter that records the number of times a bearer has
resumed after congestion or blocking, since the value is never
referenced anywhere.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates the flag in the TIPC bearer structure that indicates if
the bearer supports broadcasting, since the flag is always set to 1
and serves no useful purpose.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates a field in TIPC's bearer objects that is set, but never
referenced.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Renames items that are improperly labelled as "network scope" items
(which are represented by simple integer values) rather than "network
domain" items (which are represented by <Z.C.N>-type network addresses).
This change is purely cosmetic, and does not affect the operation of TIPC.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Combines two distinct structures containing information about a TIPC bearer
into a single structure. The structures were previously kept separate so
that public information about a bearer could be made available to plug-in
media types using TIPC's native API, while the remaining information was
kept private for use by TIPC itself. However, now that the native API has
been removed there is no longer any need for this arrangement.
Since one of the structures was already embedded within the other, the
change largely involves replacing instances of "publ.foo" with "foo".
The changes do not otherwise alter the operation of TIPC bearers.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removes several function declarations that aren't used anywhere,
either because they reference routines that no longer exist or
because all users of the function reference it after it has already
been defined.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gets rid of #include statements that are no longer required as a
result of the merging of obsolete native API header file content
into other TIPC include files.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the removal of TIPC's native API support it is no longer
necessary for TIPC to export symbols for routines that can be called
by kernel-based applications, nor for it to have header files that
kernel-based applications can include to access the declarations for
those routines. This commit eliminates the exporting of symbols by
TIPC and migrates the contents of each obsolete native API include
file into its corresponding non-native API equivalent.
The code which was migrated in this commit was migrated intact, in
that there are no technical changes combined with the relocation.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert bearer congestion inline routine that is more than one line into
a standard function, thereby eliminating some repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix TIPC to disallow sending to remote addresses prior to entering NET_MODE
user programs can oops the kernel by sending datagrams via AF_TIPC prior to
entering networked mode. The following backtrace has been observed:
ID: 13459 TASK: ffff810014640040 CPU: 0 COMMAND: "tipc-client"
[exception RIP: tipc_node_select_next_hop+90]
RIP: ffffffff8869d3c3 RSP: ffff81002d9a5ab8 RFLAGS: 00010202
RAX: 0000000000000001 RBX: 0000000000000001 RCX: 0000000000000001
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000001001001
RBP: 0000000001001001 R8: 0074736575716552 R9: 0000000000000000
R10: ffff81003fbd0680 R11: 00000000000000c8 R12: 0000000000000008
R13: 0000000000000001 R14: 0000000000000001 R15: ffff810015c6ca00
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
RIP: 0000003cbd8d49a3 RSP: 00007fffc84e0be8 RFLAGS: 00010206
RAX: 000000000000002c RBX: ffffffff8005d116 RCX: 0000000000000000
RDX: 0000000000000008 RSI: 00007fffc84e0c00 RDI: 0000000000000003
RBP: 0000000000000000 R8: 00007fffc84e0c10 R9: 0000000000000010
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fffc84e0d10 R14: 0000000000000000 R15: 00007fffc84e0c30
ORIG_RAX: 000000000000002c CS: 0033 SS: 002b
What happens is that, when the tipc module in inserted it enters a standalone
node mode in which communication to its own address is allowed <0.0.0> but not
to other addresses, since the appropriate data structures have not been
allocated yet (specifically the tipc_net pointer). There is nothing stopping a
client from trying to send such a message however, and if that happens, we
attempt to dereference tipc_net.zones while the pointer is still NULL, and
explode. The fix is pretty straightforward. Since these oopses all arise from
the dereference of global pointers prior to their assignment to allocated
values, and since these allocations are small (about 2k total), lets convert
these pointers to static arrays of the appropriate size. All the accesses to
these bits consider 0/NULL to be a non match when searching, so all the lookups
still work properly, and there is no longer a chance of a bad dererence
anywhere. As a bonus, this lets us eliminate the setup/teardown routines for
those pointers, and elimnates the need to preform any locking around them to
prevent access while their being allocated/freed.
I've updated the tipc_net structure to behave this way to fix the exact reported
problem, and also fixed up the tipc_bearers and media_list arrays to fix an
obvious simmilar problem that arises from issuing tipc-config commands to
manipulate bearers/links prior to entering networked mode
I've tested this for a few hours by running the sanity tests and stress test
with the tipcutils suite, and nothing has fallen over. There have been a few
lockdep warnings, but those were there before, and can be addressed later, as
they didn't actually result in any deadlock.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Allan Stephens <allan.stephens@windriver.com>
CC: David S. Miller <davem@davemloft.net>
CC: tipc-discussion@lists.sourceforge.net
bearer.c | 37 ++++++-------------------------------
bearer.h | 2 +-
net.c | 25 ++++---------------------
3 files changed, 11 insertions(+), 53 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Morton reported a build failure on sparc32, because TIPC
uses names like "struct node" and there is a like named data
structure defined in linux/node.h
This just regexp replaces "struct node*" to "struct tipc_node*"
to avoid this and any future similar problems.
Signed-off-by: David S. Miller <davem@davemloft.net>
Updated copyright notice to include the year the file was
actually created. Information about file creation dates
was extracted from the files in the old CVS repository
at tipc.sourceforge.net.
Signed-off-by: Per Liden <per.liden@nospam.ericsson.com>
The license header in each file now more clearly state that this
code is licensed under a dual BSD/GPL. Before this was only
evident if you looked at the MODULE_LICENSE line in core.c.
Signed-off-by: Per Liden <per.liden@nospam.ericsson.com>
TIPC (Transparent Inter Process Communication) is a protocol designed for
intra cluster communication. For more information see
http://tipc.sourceforge.net
Signed-off-by: Per Liden <per.liden@nospam.ericsson.com>
Ying Xue