The Exynos5440 common clock driver has changed the clock ID's for
some of the clocks. Fix the gmac clock entries in Exynos5440 dtsi
file accordingly.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Updated the bootargs to boot the system with rootfs in /dev/sda2
instead of ramdisk.
Signed-off-by: Subash Patel <subash.rp@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
PMU in exynos5440 generates one interrupt per core and needs to be
passed from DT to GIC to register it.
Signed-off-by: Subash Patel <subash.rp@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds node for GMAC for exynos5440 SoC supported by GMAC
driver.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos5440 pin-controller generates eight interrupts to support
gpio interrupts. List those interrupt numbers in the pin-controller
node.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds FIMD related nodes for the Origen Quad board.
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds a common FIMD device node for all Exynos4 SoCs.
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds device tree node for the SYSREG registers block
found in Samsung S5P/Exynos SoC series. The SYSREG module
generates control signals for the ARM CPU and various IP blocks
and buses. SYSREG block registers are exposed through APB bus
interface. A sysreg device tree node is to be associated with
mfd syscon driver and all SYSREG clients should use regmap
interface it provides. It allows to eliminate any possible races
and conflicts should different drivers attempt to concurrently
access same register.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This adds common FIMD device node for all Exynos5 SoCs
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos5440 has GIC which has virtualization support
in them. These are used by KVM.
Signed-off-by: Giridhar Maruthy <giridhar.m@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is a fixup to two device tree nodes that have already landed but
without clock nodes since the transition to common clock happened at
the same time.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
[gautam.vivek@samsung.com: tested on smdk5250]
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The exynos 5250 SoC supports A15 style architected timers. Indicate
this through the device tree.
This is required by KVM.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The GIC in the exynos5250 SoC is A15 compliant. Show this through
the device tree, so that we can use the GIC for KVM.
Also add the respective A15 memory regions and interrupt links.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Added HDMI hot plug and regulator nodes to Arndale DT file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
From Michal Simek <michal.simek@xilinx.com>:
It enables pmu support for zynq.
* 'zynq/core' of git://git.xilinx.com/linux-xlnx:
arm: zynq: Add support for pmu
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Michal Simek <michal.simek@xilinx.com>:
* 'zynq/clksrc/cleanup' of git://git.xilinx.com/linux-xlnx:
arm: zynq: Move timer to generic location
arm: zynq: Do not use xilinx specific function names
arm: zynq: Move timer to clocksource interface
arm: zynq: Use standard timer binding
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This series adds support for the pinctrl/gpio module on all arch-vt8500
supported SoCs.
As part of the review process, some tidy up is also done to
drivers/of/base.c to remove some code that is being constantly duplicated.
Also, a patch for the bcm2835 pinctrl driver is included to take advantage
of the new of/base.c code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRXQtJAAoJEAKiPfwuf9N/a/8H/3qun+1PnkDIGmC0amZDDrXD
tF8pruxccwOjh4Wug+UUzAwsBgej4NB193/ljFc35em9yFlZAcXBo0tLUd1gTxSd
nOkNWjYtFCK3hdmsE29Le9bRkCxn7g07uEkOKWSw79aYWrTRy63FDnr0p45YZvih
C4+ry92c50SJoW5kp+L6lS0aQjeBGXRCRcvuRBdwGPLYQXX/gEJfJrvU40ZrPByr
KJqhNOPoNS99OaVMPWDP4HCjCd/XVHBqd8Qz6M2uEIo2EBS0DnOt5IGoaRfTvEXM
Qx/y769v8/ndcdLAXFdPo+1ZgrrCXm7SozJhwAtMm3ruCxIN8u9LB6ZjMV2uaBo=
=+Y/Z
-----END PGP SIGNATURE-----
Merge tag 'vt8500/pinctrl' of git://server.prisktech.co.nz/git/linuxwmt into next/drivers
From Tony Prisk <linux@prisktech.co.nz>:
arm: vt8500: Add pinctrl driver for arch-vt8500
This series adds support for the pinctrl/gpio module on all arch-vt8500
supported SoCs.
As part of the review process, some tidy up is also done to
drivers/of/base.c to remove some code that is being constantly duplicated.
Also, a patch for the bcm2835 pinctrl driver is included to take advantage
of the new of/base.c code.
* tag 'vt8500/pinctrl' of git://server.prisktech.co.nz/git/linuxwmt: (606 commits)
pinctrl: bcm2835: make use of of_property_read_u32_index()
gpio: vt8500: Remove arch-vt8500 gpio driver
arm: vt8500: Remove gpio devicetree nodes
arm: dts: vt8500: Update Wondermedia SoC dtsi files for pinctrl driver
pinctrl: gpio: vt8500: Add pincontrol driver for arch-vt8500
arm: vt8500: Increase available GPIOs on arch-vt8500
of: Remove duplicated code for validating property and value
of: Add support for reading a u32 from a multi-value property.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Added S5M8767 PMIC DT nodes for Arndale board. Only the used
LDO's/BUCK are defined here. Also the nodes describe the default/reset
state LDO's and no power mangement tuning is implemented. The usage
desription can be found in s5m8767 device tree binding documentation.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is required to keep the existing functionality of having no
write protect pin on Arndale board.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add default pin state information for all client nodes that require
pin configuration support using pinctrl interface.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add default pin state information for all client nodes that require
pin configuration support using pinctrl interface.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
of these fixes are needed to support omap5 es2 version that includes
PM features while the earlier version es1 did not.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mjWl
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.10/fixes-non-critical-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
From Tony Lindgren <tony@atomide.com>:
Non critical omap fixes for v3.10 merge window. A big chunk
of these fixes are needed to support omap5 es2 version that includes
PM features while the earlier version es1 did not.
* tag 'omap-for-v3.10/fixes-non-critical-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: fix typo "CONFIG_BRIDGE_DVFS"
ARM: OMAP1: remove "config MACH_OMAP_HTCWIZARD"
ARM: OMAP: dpll: enable bypass clock only when attempting dpll bypass
ARM: OMAP2+: powerdomain: avoid testing whether an unsigned char is less than 0
ARM: OMAP2+: hwmod: Remove unused _HWMOD_WAKEUP_ENABLED flag
ARM: OMAP2+: am335x: Change the wdt1 func clk src to per_32k clk
ARM: OMAP2+: AM33xx: hwmod: Add missing sysc definition to wdt1 entry
Contains an update to 3.9-rc5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A couple mxs boards that run I2C at 400 kHz experience some unstable
issue occasionally. Slow down the clock speed to have I2C work
reliably.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRXCXBAAoJEFBXWFqHsHzOqg4H/irUyWQkIfch7us/vnMQnntr
y67TFoq1ucfHDA4/Okd5YxeUWjh0vaFJTVu5JLKfuT7HGTzSeqG4sFCp/A6/i9F9
ZGbcmTUSgG3erjpzN0R+PLxWO5iqjT8Mg3/cyK83SguKtf4u/MVJq8jpTyc0JJ9R
UNj4OaKN5n7tvPGAkj8ypWDpQwlczRRie6v+Nt1qWP1K7T7Ez9ZMkhOvd7WLUi4T
H7HcWo5IOUBzLvf7JmBAQwTCTdl7BJglBO5FjTn7ao0uaMEHLJOwzPWdXs08Agzh
qMVJcWqVCcQQmB5nuDDb08mlXXEYrt/92qL3LUejJaX76bPH+lzfCnvrDGUIuvo=
=Towm
-----END PGP SIGNATURE-----
Merge tag 'mxs-fixes-3.9-4' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The mxs fixes for 3.9, take 4:
- A couple mxs boards that run I2C at 400 kHz experience some unstable
issue occasionally. Slow down the clock speed to have I2C work
reliably.
* tag 'mxs-fixes-3.9-4' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: Slow down the I2C clock speed
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Instead of using a custom binding for retrieving the GPIO that activates the
LCD from devicetree, use a standard regulator.
This approach has the advantage to be more generic.
For example: in the case of a board that has a PMIC supplying the LCD voltage,
the current approach would not work, as it only searches for a GPIO pin.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The recent dtc+cpp support allows header files and C pre-processor
defines/macros to be used when compiling device tree files. These
headers will typically define various constants that are part of the
device tree bindings.
The original patch which set up the dtc+cpp include path only considered
using those headers from device tree files. However, most are also
useful for kernel code which needs to interpret the device tree.
In both the DT files and the kernel, I'd like to include the DT-related
headers in the same way, for example, <dt-bindings/gpio/tegra-gpio.h>.
That will simplify any text which discusses the DT header locations.
Creating a <dt-bindings/> for kernel source to use is as simple as
placing files into include/dt-bindings/.
However, when compiling DT files, the include path should be restricted
so that only the dt-bindings path is available; arbitrary kernel headers
shouldn't be exposed. For this reason, create a specific include
directory for use by dtc+cpp, and symlink dt-bindings from there to the
actual location of include/dt-bindings/. For want of a better location,
place this "include chroot" into the existing dts/ directory.
arch/*/boot/dts/include/dt-bindings -> ../../../../../include/dt-bindings
Some headers used by device tree files may not be useful to the kernel;
they may be used simply to aid in constructing the DT file (e.g. macros
to create a node), but not define any information that the kernel needs
to share. These may be placed directly into arch/*/boot/dts/ along with
the DT files themselves.
Acked-by: Michal Marek <mmarek@suse.cz>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
"ip" and "root" settings are useful for development
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Correct IDs for cdev1 and cdev2 are 94 and 93 respectively.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: split into separate driver and device-tree patches]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Adding the PM configuration of PMC when the platform support suspend
function.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds "non-removable" property of MMC host where the eMMC device
is for Tegra platform.
And the "keep-power-in-suspend" property was used for the SDIO device that
need this to go into suspend mode (e.g. BRCM43xx series).
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This adds the power gpio key to DT and enable the wakeup of the gpio key
for the device. The Seaboard and paz00 already had the power gpio key
binding and the power key of Whistler was on KBC. So these boards' device
tree didn't include in this patch.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Set "regulator-always-on" for the SD slot on Dalmore, so that SD cards
work. This used to work, since this regulator is on by default, but was
broken by commit "ARM: tegra: dalmore: add TPS65090 node", since that
didn't specify always-on for this regulator.
In the long run, the regulators should all be hooked up to the SDHCI
device nodes. However, we haven't done that for any of the Tegra boards
yet, so to be consistent, this patch simply forces the regulator on,
rather than hooking it up and making it work differently to other boards.
Reported-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Audio-related clocks need to be represented in the device tree. Update
bindings to describe which clocks are needed, and DT files to include
those clocks.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Audio-related clocks need to be represented in the device tree. Update
bindings to describe which clocks are needed, and DT files to include
those clocks.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 reference platform Dalmore has voltage switch
regulators which are controlled by the Tegra GPIOs.
Add DT node for fixed regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 reference platform, Dalmore, uses the TPS65090 as
secondary PMICs which is mainly act as voltage switch regulator
controlled by i2c communication.
Add DT node for TPS65090.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: remove unit-address from node name since it's unique already]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Dalmore uses the TPS51632 as CPU regulator. The device is connected
on I2C5.
Add DT node for TPS51632.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds the node for the bq20z45 I2C gas gauge which is
compatible with the sbs-battery power supply driver.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[swarren: remove unit-address from node name since it's unique already]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 has 6 SPI controllers. These controllers are
redesign on T114 with different register interface.
Add DT entry for spi controllers and make it compatible with
"nvidia,tegra114-spi", since they are a new incompatible design.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed reg property for 3rd SPI controller]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 SoCs have the matrix keyboard controller which
supports 11x8 type of matrix. The number of rows and columns
are configurable.
Add DT entry for KBC controller with compatibility as "nvidia,tegra114-kbc".
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add APB DMA requestor and serial aliases for serial controller.
There are two serial drivers i.e. 8250 based simple serial driver
and APB DMA based serial driver for higher baudrate and performace.
The simple serial driver is selected by compatible value
"nvidia,tegra114-uart", "nvidia,tegra20-uart", and the APB DMA based
driver is selected by compatible value "nvidia,tegra114-hsuart",
"nvidia,tegra30-hsuart".
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 has 5 I2C controllers. These controllers have the
following changes which makes incompatible with previous hardware:
- Single clock source to I2C controller.
- Interrupt support for per packet transfer.
Add DT entry for I2C controllers and make it compatible with
"nvidia,tegra114-i2c".
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed location of status property for consistency]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
NVIDIA's Tegra114 has 32 channels APB DMA controller. Add DT entry for
APB DMA controllers and make it compatible with "nvidia,tegra114-apbdma".
Tegra114 DMA controller is not compatible with Tegra30/Tegra20 DMA
controller driver as in Tegra114, the global pause also clock gate the
DMA register and hence it iw not possible to write the DMA register
with global pause.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed DT node order]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds a device tree node for the four PWM controllers present
on Tegra114.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
We should be defining the PWM nodes with status as "disabled" in the
chip-specific dtsi file, since we don't know whether specific boards
will use the PWM or not. This patch fixes the PWM node status for
Tegra20 and Tegra30.
Also fixed the one user of PWM, which is the Tegra20 medcom-wide board,
so that PWM is set to "okay" in the board-specific dts file.
Signed-off-by: Andrew Chew <achew@nvidia.com>
[swarren: in medcom-wide: fixed node sort order, removed duplicate pwm:
label, fixed syntax error]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Dalmore has a built-in eMMC device and a user-accessible SD card slot.
Add device tree nodes to enable these.
Based on changes by: Pritesh Raithatha <praithatha@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[swarren: added commit description, fixed DT node sort order]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds in the SDHCI nodes for the busses supported on Tegra114
boards.
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>
[Rhyland added clk refs to & reordered sdhci nodes and removed spaces]
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[swarren: fixed DT node sort order]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The USB PHY nodes are all grouped together rather than being sorted based
on reg address like all other nodes fix this.
I apologize for the churn; I should have noticed this during review of the
patches that caused this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add references to tegra_car clocks for the basic device nodes. Also remove
the clock-frequency property of the serial node as the UART driver can now
use the clock framework to obtain the frequency.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The port controller needs the apb0_pio clock enabled to be able to
work. This commit declares that on the device tree.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All the UARTs are connected to clock gates; now that our clock driver
is able to handle them, make the switch.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit adds the corresponding DT bindings for all the AXI,
AHB, APB0 and APB1 gates.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the ADC low and high resolution configuration and which one to use.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Macb0 node cannot be activated in generic sam9x5ek.dtsi file
as the sam9g15 does not have one.
Move the macb0 & macb1 activation in board .dts file that
support them.
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Move display timing configurations into device tree, so that the
auxdata for mxsfb driver can be killed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Put the clock to the devicetree, so the driver can take care of it
later. Then, we don't have to do the enabling as a workaround in board
init.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
[shawn.guo: add enet_out into imx28.dtsi and overwrite it for m28evk]
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Now that a display timing binding is available, convert our almost identical
binding to use the standard binding.
This patch converts the vt8500 and wm8505 framebuffer drivers and
associated dts/dtsi files to use the standard binding as defined in
bindings/video/display-timing.txt.
There are two side-effects of making this conversion:
1) The fb node should now be in the board file, rather than the soc file as
the display-timing node is a child of the fb node.
2) We still require a bits per pixel property to initialize the framebuffer
for the different lcd panels. Rather than including this as part of the
display timing, it is moved into the framebuffer node.
I have also taken the opportunity to alphabetise the includes of each
driver to avoid double-ups.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The zynq has a Cortex-A9 with the corresponding smp_twd timers. Use them.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynq is standard PMU with 2 interrupt per core.
There is also access via register which is not used right now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use cdns,ttc because this driver is Cadence Rev06
Triple Timer Counter and everybody can use it
without xilinx specific function name or probing.
Also use standard dt description for timer
and also prepare for moving to clocksource
initialization.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove the gpio related devicetree nodes as these are no longer required
with the move to a combined pinctrl/gpio driver.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds pinctrl nodes to the VIA VT8500 and Wondermedia SoC dtsi
files to support the pinctrl driver.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Highlights:
* Add Lager board support
* Add ape6evm board support
* Add Bock-W board support
* Mackerel MMCIF/SDHI clean ups
* Add ethernet support to kzm9g-reference
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-pinmux2-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-boards2-for-v3.10
The merge with renesas-pinmux2-for-v3.10 was made to provide
run-time dependencies for the following changes:
ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Zhif
-----END PGP SIGNATURE-----
Merge tag 'renesas-boards3-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards2
Third round of Renesas ARM SoC board updates for v3.10
Highlights:
* Add Lager board support
* Add ape6evm board support
* Add Bock-W board support
* Mackerel MMCIF/SDHI clean ups
* Add ethernet support to kzm9g-reference
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-pinmux2-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-boards2-for-v3.10
The merge with renesas-pinmux2-for-v3.10 was made to provide
run-time dependencies for the following changes:
ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support
* tag 'renesas-boards3-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (307 commits)
ARM: shmobile: mackerel: clean up MMCIF vs. SDHI1 selection
ARM: shmobile: mackerel: add interrupt names for SDHI0
ARM: shmobile: mackerel: switch SDHI and MMCIF interfaces to slot-gpio
ARM: shmobile: mackerel: remove OCR masks, where regulators are used
ARM: shmobile: mackerel: SDHI resources do not have to be numbered
ARM: shmobile: Initial r8a7790 Lager board support
ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support
ARM: shmobile: APE6EVM base support
ARM: shmobile: kzm9g-reference: add ethernet support
ARM: shmobile: add R-Car M1A Bock-W platform support
sh-pfc: r8a73a4: Remove unused GPIO bias data
ARM: shmobile: r8a73a4: Remove all GPIO enums
sh-pfc: r8a73a4: Remove function GPIOs
ARM: shmobile: r8a73a4: Remove IRQC function GPIOs
ARM: shmobile: r8a73a4: Remove SCIF function GPIOs
sh-pfc: r8a73a4: Remove IRQC function GPIOS
sh-pfc: r8a73a4: Remove SCIF function GPIOS
sh-pfc: r8a73a4: Add IRQC pin groups and functions
sh-pfc: r8a73a4: Add SCIF pin groups and functions
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds a device tree binding for random number generator present on
Broadcom BCM2835 SoC, used in Raspberry Pi and Roku 2 devices.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Highlights:
* Compilation fixes for sh7269 and for when CONFIG_BUG is not set
* sh-pfc Support for r8a73a4 SoC
* Move GPIOs handling from the PFC device to separate GPIO devices on the r8a7779 SoC
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-pinmux-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc2-for-v3.10
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=vwDo
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinmux2-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc2
Second round of Renesas ARM and SH based SoC pinmux updates for v3.10
Highlights:
* Compilation fixes for sh7269 and for when CONFIG_BUG is not set
* sh-pfc Support for r8a73a4 SoC
* Move GPIOs handling from the PFC device to separate GPIO devices on the r8a7779 SoC
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-pinmux-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc2-for-v3.10
* tag 'renesas-pinmux2-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (185 commits)
sh-pfc: r8a73a4: Remove unused GPIO bias data
ARM: shmobile: r8a73a4: Remove all GPIO enums
sh-pfc: r8a73a4: Remove function GPIOs
ARM: shmobile: r8a73a4: Remove IRQC function GPIOs
ARM: shmobile: r8a73a4: Remove SCIF function GPIOs
sh-pfc: r8a73a4: Remove IRQC function GPIOS
sh-pfc: r8a73a4: Remove SCIF function GPIOS
sh-pfc: r8a73a4: Add IRQC pin groups and functions
sh-pfc: r8a73a4: Add SCIF pin groups and functions
sh-pfc: r8a73a4: Add bias (pull-up/down) pinconf support
sh-pfc: r8a73a4: GPIO IRQ support
sh-pfc: r8a73a4: Support sparse GPIO numbers
sh-pfc: Add r8a73a4 pinmux support
sh-pfc: r8a7779: Split DU input and output pixel clocks
sh-pfc: r8a7779: Remove GPIO data
ARM: shmobile: r8a7779: Register GPIO devices
sh-pfc: Configure pins as GPIOs at request time when handled externally
sh-pfc: Skip gpiochip registration when no GPIO resource is found
sh-pfc: Make GPIO support optional
sh-pfc: Make function GPIOs support optional
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Some Highlights:
* Add r8a7790 SoC
* Add r8a73a4 SoC
* Migrate r8a7740 SoC from INTC to GIC
* Add thermal driver support to r8a73a4 SoC
* Add irqpin DT nodes to sh73a0 SoC
* Add SCIF support to r8a7778 SoC
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-intc-external-irq2-for-v3.10
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRWmXUAAoJENfPZGlqN0++r7YQAI47GqgjuqQsE4XUGaM12Rxz
vTpJ4l9AfDcZxnLbRG80QuMYUInhiBExH1MA3wtAmgLRNpFOOUH12rM54Y8M5oLy
AbN/rvf7ReM0eQBlBlu7TUAUxPLRMzTyo1auBXIFM3Qjp5udf5bd3eFWBduQhaIA
ltr+7czw96KpHtprbeRjR5qelFXATF9kW0rI8E9CRb6lLrHQ6BS7HO6UH5AcnB5V
8iVj/hWFV11KKsiP+BJDa8pXqFJUjAeYipYJ7wA0cTqKz3IgHnHnEcsyGmSmjHoX
NOxPZWB9b5zYNn5dXdyTlpHC592hdS4EPGuzlHceiphxFvJ5Ay83b3braU5SUd0O
ArzDg/acR2Uov35wWYPoiAkQMaf1U97TEUw4q5+bO4r+12SIt+iuevQkYx72YZjR
qVcCK895y0sMyfRafcz9Apoy8Rnimjfc+dMOebt2lHE33tXCZ4KxD+YVTeNm5OIG
/QqVZuqi4DzSpQgJwpYf9DlRCNg2PKA8r+0pBT+xRDDj+MPbw10IMHjx/ZNJthvX
r9yyupNEsa1goT7wbDHq5bJw41D5JGldYlKZz6Tz0h7eQFPdSkE6F1Usa74fMKSF
VcAlvKmb7rR/ZRWILKGrPKTAzZKedSY6RYmhJEgSxnYQYt2fmUu6bAIu09s9J6BC
XEC7K7rRuQh1C6vu/t/D
=jivx
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc2-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc2
Second round of Renesas ARM SoC updates for v3.10
Some Highlights:
* Add r8a7790 SoC
* Add r8a73a4 SoC
* Migrate r8a7740 SoC from INTC to GIC
* Add thermal driver support to r8a73a4 SoC
* Add irqpin DT nodes to sh73a0 SoC
* Add SCIF support to r8a7778 SoC
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-intc-external-irq2-for-v3.10
* tag 'renesas-soc2-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (88 commits)
ARM: shmobile: r8a7790 SoC 64-bit DT support
ARM: shmobile: r8a73a4 SoC 64-bit DT support
ARM: shmobile: r8a7790 PFC support
ARM: shmobile: r8a7790 IRQC support
ARM: shmobile: r8a7790 SCIF support
ARM: shmobile: Initial r8a7790 SoC support
ARM: shmobile: r8a7779: move global functions to r8a7779.h
ARM: shmobile: r8a7740: move global functions to r8a7740.h
ARM: shmobile: sh73a0: move global functions to sh73a0.h
ARM: shmobile: sh7372: move global functions to sh7372.h
ARM: shmobile: r8a7779: remove DIV4 clocks and use fixed ratio clock
ARM: shmobile: r8a7740: use fixed ratio clock
ARM: shmobile: r8a7740: tidyup comment/implementation mismatch
ARM: shmobile: sh73a0: use fixed ratio clock
ARM: shmobile: sh7372: use fixed ratio clock
ARM: shmobile: add struct clk_ratio and fixed ratio clock macro
ARM: shmobile: sh7372: remove DIV4_ZT* clocks
ARM: shmobile: sh73a0: remove DIV4_ZT* clocks
ARM: shmobile: sh73a0: add a TWD clock
ARM: shmobile: r8a7740: Migrate from INTC to GIC
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add tps6507x regulator device tree data to da850-evm by
adding regulator consumers with tightened constraints
and regulator-name.TPS6507x regulator handle can be obtained
by using this regulator name.
Regulator constraints are added as per da850 board file.
Regulator names are given as per maximum output voltage the
regulator is capable to provide.
for e.g. regulator name for dcdc1 is "VDCDC1_3.3V".
Also, add tps6507x PMIC I2C slave device under I2C0 node.
Tested on da850-evm.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add device tree data for tps6507x regulator by adding
all tps6507x regulator nodes. Regulators are initialized
based on compatible name provided in tps6507x DT file.
All tps6507x PMIC regulator device tree nodes are placed
in a separate device tree include file (tps6507x.dtsi).
tps6507x.dtsi file is created using datasheet
http://www.ti.com/lit/ds/symlink/tps65070.pdf
Tested on da850-evm.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch adds support for the thermal controller available in
all Armada 370 boards. This controller has two 4-byte registers:
one to read the thermal sensor, the other for sensor initialization.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds support for the thermal controller available in
all Armada XP boards. This controller has two 4-byte registers:
one to read the thermal sensor, the other for sensor initialization.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Lager base board support making use of 2 GiB of memory,
the r8a7790 SoC with the SCIF0 serial port and CA15 with
ARM architected timer.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add LAN9220 support to the APE6EVM board using C and DT.
At this point the PFC driver lacks DT bindings so to
configure the PFC we use PINCTRL in C board code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
V3 of APE6EVM base board support making use of
1 GiB of memory, the SCIFA0 serial port and
ARM architected timer.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the SMSC 9221 ethernet chip, found on kzm9g, to its
reference implementation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add basic Bock-W board support
More devices will be added on top of this patch after
PICNTRL and clock framework are in better shape.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Highlights:
* Compilation fixes for sh7269 and for when CONFIG_BUG is not set
* sh-pfc Support for r8a73a4 SoC
* Move GPIOs handling from the PFC device to separate GPIO devices on the r8a7779 SoC
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-pinmux-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc2-for-v3.10
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=vwDo
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinmux2-for-v3.10' into boards-base
Second round of Renesas ARM and SH based SoC pinmux updates for v3.10
Highlights:
* Compilation fixes for sh7269 and for when CONFIG_BUG is not set
* sh-pfc Support for r8a73a4 SoC
* Move GPIOs handling from the PFC device to separate GPIO devices on the r8a7779 SoC
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-pinmux-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc2-for-v3.10
This merge is made to supply run-time dependencies for the following
patches that will bea added on top:
ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support
Slow down the I2C clock speed on M28 and SPS1 as it turns out the
I2C block in i.MX28 can not operate stable enough with the bus
running at 400kHz. Note that the driver used by Freescale runs
the bus at 250kHz when 400kHz speed is selected, but the mainline
Linux kernel runs the bus at actual 400kHz and that's where it is
occasionally unstable. Play safe and run the bus at 100kHz.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This adds support for the Broadcom timer, used in the following SoCs:
BCM11130, BCM11140, BCM11351, BCM28145, BCM28155
Updates from V6:
- Split DT portion into a separate patch
Updates from V5:
- Rebase to latest arm-soc/for-next
Updates from V4:
- Switch code to use CLOCKSOURCE_OF_DECLARE
Updates from V3:
- Migrate to 3.9 timer framework updates
Updates from V2:
- prepend static fns + fields with kona_
Updates from V1:
- Rename bcm_timer.c to bcm_kona_timer.c
- Pull .h into bcm_kona_timer.c
- Make timers static
- Clean up comment block
- Switched to using clockevents_config_and_register
- Added an error to the get_timer loop if it repeats too much
- Added to Documentation/devicetree/bindings/arm/bcm/bcm,kona-timer.txt
- Added missing readl to timer_disable_and_clear
Note: bcm,kona-timer was kept as the 'compatible' field to make it
specific enough for when there are multiple bcm timers (bcm,timer is
too generic).
Signed-off-by: Christian Daudt <csd@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Introduction of new Atmel Cortex-A5: SAMA5D3 family.
- Modify AT91 Kconfig to plit ARMv4/5 and ARMv7 arch
- Modify PMC driver (clocks)
- Core SAMA5 support
- Board file, DT files and defconfig
* tag 'at91-soc' of git://github.com/at91linux/linux-at91:
ARM: at91: add defconfig for SAMA5
ARM: at91: dt: add device tree files for SAMA5D3 family
ARM: at91: introduce SAMA5 support
ARM: at91: introduce the core type choice to split ARMv4/5 and ARMv7 arch
ARM: at91: add AT91_SAM9_TIME entry to select at91sam926x_time.c compilation
ARM: at91: change name template in AT91_SOC_START macro
ARM: at91: renamme rm9200 dt file
ARM: at91: rename board-dt to more specific name board-dt-sam9
ARM: at91: move non DT Kconfig to Kconfig.non_dt
Signed-off-by: Olof Johansson <olof@lixom.net>
Provide RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device.
Also provide pin multiplexer information for USB host
pins.
CC: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After a quiet set of fixes for 3.9-rc4, a lot of people woke up and sent
urgent fixes for 3.9. I pushed back on a number of them that got
deferred to 3.10, but these are the ones that seemed important.
Regression in 3.9:
- Multiple regressions in OMAP2+ clock cleanup
- SH-Mobile frame buffer bug fix that merged here because of maintainer MIA
- ux500 prcmu changes broke DT booting
- MMCI duplicated regulator setup on ux500
- New ux500 clock driver broke ethernet on snowball
- Local interrupt driver for mvebu broke ethernet
- MVEBU GPIO driver did not get set up right on Orion DT
- incorrect interrupt number on Orion crypto for DT
Long-standing bugs, including candidates for stable:
- Kirkwood MMC needs to disable invalid card detect pins
- MV SDIO pinmux was wrong on Mirabox
- GoFlex Net board file needs to set NAND chip delay
- MSM timer restart race
- ep93xx early debug code broke in 3.7
- i.MX CPU hotplug race
- Incorrect clock setup for OMAP1 USB
- Workaround for bad clock setup by some old OMAP4 boot loaders
- Static I/O mappings on cns3xxx since 3.2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=oQbL
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Arnd Bergmann:
"After a quiet set of fixes for 3.9-rc4, a lot of people woke up and
sent urgent fixes for 3.9. I pushed back on a number of them that got
deferred to 3.10, but these are the ones that seemed important.
Regression in 3.9:
- Multiple regressions in OMAP2+ clock cleanup
- SH-Mobile frame buffer bug fix that merged here because of
maintainer MIA
- ux500 prcmu changes broke DT booting
- MMCI duplicated regulator setup on ux500
- New ux500 clock driver broke ethernet on snowball
- Local interrupt driver for mvebu broke ethernet
- MVEBU GPIO driver did not get set up right on Orion DT
- incorrect interrupt number on Orion crypto for DT
Long-standing bugs, including candidates for stable:
- Kirkwood MMC needs to disable invalid card detect pins
- MV SDIO pinmux was wrong on Mirabox
- GoFlex Net board file needs to set NAND chip delay
- MSM timer restart race
- ep93xx early debug code broke in 3.7
- i.MX CPU hotplug race
- Incorrect clock setup for OMAP1 USB
- Workaround for bad clock setup by some old OMAP4 boot loaders
- Static I/O mappings on cns3xxx since 3.2"
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: cns3xxx: fix mapping of private memory region
arm: mvebu: Fix pinctrl for Armada 370 Mirabox SDIO port.
arm: orion5x: correct IRQ used in dtsi for mv_cesa
arm: orion5x: fix orion5x.dtsi gpio parameters
ARM: Kirkwood: fix unused mvsdio gpio pins
arm: mvebu: Use local interrupt only for the timer 0
ARM: kirkwood: Fix chip-delay for GoFlex Net
ARM: ux500: Enable the clock controlling Ethernet on Snowball
ARM: ux500: Stop passing ios_handler() as an MMCI power controlling call-back
ARM: ux500: Apply the TCPM and TCDM locations and sizes to dbx5x0 DT
fbdev: sh_mobile_lcdc: fixup B side hsync adjust settings
ARM: OMAP: clocks: Delay clk inits atleast until slab is initialized
ARM: imx: fix sync issue between imx_cpu_die and imx_cpu_kill
ARM: msm: Stop counting before reprogramming clockevent
ARM: ep93xx: Fix wait for UART FIFO to be empty
ARM: OMAP4: PM: fix PM regression introduced by recent clock cleanup
ARM: OMAP3: hwmod data: keep MIDLEMODE in force-standby for musb
ARM: OMAP4: clock data: lock USB DPLL on boot
ARM: OMAP1: fix USB host on 1710
Conflicts:
drivers/pinctrl/sh-pfc/pfc-r8a7740.c
This merge is to provide r8a73a4 SoC files, which are added in the
soc branch and depended on by r8a73a4 pfc-changes which are to
be added to the pinmux branch.
The r8a7790 SoC supports LPAE and has memory window up to
0x2ffffffff. Convert to 64-bit addresses by enlarging
#addr-cells and #size-cells to 2.
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a73a4 SoC supports LPAE and has memory window up to
0x2ffffffff. Convert to 64-bit addresses by enlarging
#addr-cells and #size-cells to 2.
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add IRQC interrupt controller support to r8a7790 by
hooking up a single IRQC instances to handle 4 external
IRQ signals. The IRQC controller is tied to SPIs of
the GIC. On r8a7790 the external IRQ pins routing is
handled by the PFC which is excluded from this patch.
Both platform devices and DT devices are added in this
patch. The platform device versions are used to provide
a static interrupt map configuration for board code
written in C.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the r8a7790 SoC including:
- Single Cortex-A15 CPU Core
- GIC
- Architecture timer
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
You can get current thermal by
> cat /sys/class/thermal/thermal_zone?/temp
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT nodes for the 4 irqpin interrupt controllers on sh73a0. We add them
to sh73a0.dtsi, which is also used by configurations, doing all their
device instantiation from board the .c code. We rely on the fact, that
such configurations don't instantiate devices from the device-tree.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the R8A7778 R-Car M1A SoC.
No static virtual mappings are used, all the components
make use of ioremap().
DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
It is based on v1.0 datasheet
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add IRQC interrupt controller support to r8a73a4 by
hooking up two IRQC instances to handle 58 external
IRQ signals. There IRQC controllers are tied to SPIs
of the GIC. On r8a73a4 exact IRQ pin routing is handled
by the PFC which is excluded from this patch.
Both platform devices and DT devices are added in this
patch. The platform device versions are used to provide
a static interrupt map configuration for board code
written in C.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
V3 of initial support for the r8a73a4 SoC including:
- Single Cortex-A15 CPU Core
- GIC
- Architecture timer
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In the conversion to pinctrl, an error in the pins for the rebuild
LED was introduced. This patch assigns the correct pins and includes
the correct name for the LED in kirkwood-iomega_ix2_200.dts.
Signed-off-by: Nigel Roberts <nigel@nobiscuit.com>
Cc: <stable@vger.kernel.org> # v3.8.x
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Instead of using static address definition, get reset address from
device tree with mapping, so that core_initcall mxs_arch_reset_init()
can be killed.
The "rtc" clock code in mxs_arch_reset_init() seems to be zombie, since
there is no clk lookup defined in clock driver at all. Remove it
together.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instead of using the static definitions, get clkctrl and digctl base
addresses with mapping from device tree.
Use macro on variable is not nice, but it's done here to save huge
pointless diff stat.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Change call clk_get_sys() to of_clk_get() to look up timrot clock from
device tree, so that the clk_register_clkdev() call for timrot can be
saved in clock driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add the three external LED definitions to the device tree file on
the Mirabox.
The Mirabox user guide calls out one as a power LED, and the other
two are defined for WiFi, but as the current mwifiex drivers don't
have LED support, we make them status LEDs.
These have been tested working by writing to the appropriate
/sys/class/leds trigger.
Signed-off-by: Ryan Press <ryan@presslab.us>
Tested-by: Neil Greatorex <neil@fatboyfat.co.uk>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The orion5x SoC includes DMA functionality, so lets enable that
and turn it on by default.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The orion5x SoC also includes a USB EHCI componment so lets add that
to the dtsi (disable by default incase the pins are not broken out).
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Device tree based guruplug boards still use mvsdio platform_data and
kirkwood_sdio_init to enable sdio. DT support for sdio is already there,
so make use of it.
This also fixes mvsdio accidentially breaking nand by configuring mpp0
to gpio, while used also by nand (nand_io2 on mpp0).
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Soeren Moch <smoch@web.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Marvell Armada 370 Reference Design board has a software-controlled
button on the front side, marked as "SW".
This patch adds minimal support for this button.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
We previously relied on the bootloader to do the muxing of the UART for
the Cubieboard. Don't rely on it anymore and use pinctrl.
Also remove uart1, as it is not enabled by default and it's not exposed
on the board headers.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We previously relied on the bootloader to do the muxing of the UART for
the Hackberry. Don't rely on it anymore and use pinctrl.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
The Allwinner A10 SoC has 8 available UARTs, which is 6 more than on the
A13, so add the missing UARTs to the sun4i-a10 dtsi.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
Both A10 and A13 Allwinner SoCs have a Synopsys APB uart3 device
available, so add it to the sunxi.dtsi file
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
The UART0 is only available on the Allwinner A10 SoCs, and not on the
A13, so move the uart0 node to sun4i-a10.dtsi.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
Tested-by: Emilio López <emilio@elopez.com.ar>
The other architecture use serial@address for their uart nodes, so
rename our uart dt nodes to be consistent
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
It will be especially useful when we will have the clock definitions in
the device tree.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
Tested-by: Emilio López <emilio@elopez.com.ar>
- mvebu
- interrupt fix
- DT pinctrl definition for sdio
- kirkwood
- chip-delay for GoFlex Net (fix reading nand)
- set mvsdio unused pins to invalid value for legacy boards (0 is valid)
- orion5x
- fix typo in gpio parameters
- use correct irq in dtsi
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRVIcVAAoJEAi3KVZQDZAev1wH/0oIYEZvAeE8Nh49bn7EKgwH
ef44bin9g/JkEZ/3YndUE+1wqq/4nBaJN2IWGsPmbKGZFWNaoaPG1gFr0VsOepge
GpKdwrxUMAgIzLO+4FtN85Zy3Qe4Jn8YWjJcZXZbl404cyQx5bDID0clYsn0m2jW
F6nWva5ULAbWNBsUpRQ3h8nYfKi9QsWvhOgFxsaAiR3VCpLOk+MKK7Y0cwqpi60K
p2ALUultfXGckqJyFCoZNHwN52dlllsXD09i/lRzM91nT/VEPzwWNhPcoNjwiQwu
qfloTU97Lfq7168G4PTSEq8V7LP/NLbAlwwJ3VW3HCrtVTefSQFdUF9EA9bjl8I=
=EExD
-----END PGP SIGNATURE-----
Merge tag 'mvebu_fixes_for_v3.9_round2' of git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper <jason@lakedaemon.net>:
mvebu fixes for v3.9 (round 2)
- mvebu
- interrupt fix
- DT pinctrl definition for sdio
- kirkwood
- chip-delay for GoFlex Net (fix reading nand)
- set mvsdio unused pins to invalid value for legacy boards (0 is valid)
- orion5x
- fix typo in gpio parameters
- use correct irq in dtsi
* tag 'mvebu_fixes_for_v3.9_round2' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: Fix pinctrl for Armada 370 Mirabox SDIO port.
arm: orion5x: correct IRQ used in dtsi for mv_cesa
arm: orion5x: fix orion5x.dtsi gpio parameters
ARM: Kirkwood: fix unused mvsdio gpio pins
arm: mvebu: Use local interrupt only for the timer 0
ARM: kirkwood: Fix chip-delay for GoFlex Net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for NETGEAR ReadyNAS Duo v2 (Hardware specs available
here: http://natisbad.org/NAS/). Almost everything is supported via
provided .dts. A board-readynas.c file is nonetheless required for
device not only converted to DT (Gbit controller).
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Tested-By: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The previous configuration used the wrong "clk" pin. Without this
change mv_sdio worked because the bootloader would set the pin up, but
with a bootloader that does not set the pin, mv_sdio fails to detect any
card.
I have tested this change using a mwifiex_sdio wireless network adapter
over the SDIO interface.
Signed-off-by: Ryan Press <ryan@presslab.us>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The crypto functionality in the orion5x dtsi uses the Ethernet IRQ and
so things do not work and there is much grumbling at boot time.
The IRQ for the crypto should be 28, and not 22, and that is what this
patch corrects.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
orion5x.dtsi is missing the gpio alias as well as including a typo
('ngpio' instead of 'ngpios') that prevented the orion-gpio driver
from loading. Also missing were the interrupt-controller properties.
This patches resolves those glitches.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This fixes "Too few good blocks within range" issues on GoFlex Net by setting
chip-delay to 40.
The basic problem was discussed at http://forum.doozan.com/read.php?2,7451
Signed-off-by: Eric Hutter <hutter.eric@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: <stable@vger.kernel.org> # v3.6.x
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
- Get TCPM and TCDM locations from the device tree
- Skip passing the ios_handler for the MMCI
- Enable the ethernet clock for Snowball
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=v6nX
-----END PGP SIGNATURE-----
Merge tag 'ux500-fixes-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij <linus.walleij@stericsson.com>:
Fixes boot regressions on Device Tree:
- Get TCPM and TCDM locations from the device tree
- Skip passing the ios_handler for the MMCI
- Enable the ethernet clock for Snowball
* tag 'ux500-fixes-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Enable the clock controlling Ethernet on Snowball
ARM: ux500: Stop passing ios_handler() as an MMCI power controlling call-back
ARM: ux500: Apply the TCPM and TCDM locations and sizes to dbx5x0 DT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
During the introduction of the Allwinner SoC platforms, sunxi was
initially meant as a generic name for all the variants of the Allwinner
SoC.
It was ok at the time of the support of only the A10 and A13 that
look pretty much the same; but it's beginning to be troublesome with
the future addition of the Allwinner A31 (sun6i) that is quite
different, and would introduce some weird logic, where sunxi would
actually mean in some case sun4i and sun5i but without sun6i...
Moreover, it makes the compatible strings naming scheme not consistent
with other architectures, where usually for this kind of compability, we
just use the oldest SoC name that has this IP, so let's do just this.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This fixes a regression introduced by commit:
05ec260 mfd:db8500-prcmu: update resource passing
All DBx5x0 based SoCs have access to two Tightly Coupled Memory
(TCM) locations based on the PRCMU itself. One area from program
memory (TCPM) and one for data memory (TCDM). The PRCMU needs to
know where these are in order to function correctly. However,
these are currently passed though platform device resources, which
can only be obtained if Device Tree booting isn't in use. Thus we
must also support them in DT by supplying them through the PRCMU
node.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Conflicts:
include/net/ipip.h
The changes made to ipip.h in 'net' were already included
in 'net-next' before that header was moved to another location.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gc7f
-----END PGP SIGNATURE-----
Merge tag 'arizona-extcon-asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into char-misc-next
Mark writes:
ASoC/extcon: arizona: Fix interaction between HPDET and headphone outputs
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
Add device tree files for the SAMA5D3 family (SAMA5D31, SAMA5D33, SAMA5D34 and
SAMA5D35).
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The SSBI bus is exclusive to the Qualcomm MSM targets, and all SoCs
using it will be using device tree. Convert this driver to indentify
with device tree.
This makes the bus probing a good bit simpler, since the attaching of
child nodes can be represented directly in the devicetree, rather than
having to be inferred by name.
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Four patches for arm-soc this week:
- Kevin Hilman is no longer reachable under his previous email address.
He submitted the patch earlier, but nobody felt responsible to pick
it up.
- One Tegra fix for an incorect register address in device tree.
- IMX multiplatform support exposes a configuration option that
leads to unbootable kernels on all other machines and that needs
to depend on that platform.
- A nontrivial bug fix for the setup of the mxs video output.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUVBQf2CrR//JCVInAQJwyRAA0qzt+jbn+ezvLpeWvrgdEVLikiAieVyt
HmSex/pEWh2ytIkrX2maHv5Oov9QmX7v4ZEU2WtdvMv5YERsT7/y1hjHaZTLcdmH
11ogfVwTRbrNVWOb41ofdd3rUVgZfgzCGQ0rfEua3wLRK6AetZJxkqsuGXRaqjdm
BBbmgKAmLsLeM3/aBzeuFint1+EDY74WBMxgqkwUretefKFMxzcBaqhoR+FNDIdV
YaYbOocq45LsOa44gxlF6pmJkZsOsB2pqAjoANm5KtZlphTEpDD1C/wXvBaVAOBh
8mCuk2mHEyZsyLrufh/ZywaPcDaUMDwpO1zidATwaRCf6qWOr3jtWiCtQo4FeNYS
o+kkYtELyAEvwDQuljghviq0p+z2vpnk52sYdXkYW8Pgz5TqhK+Gu2ywaeiqeT2B
cbLGG32lVgJnmWOOXI7Z6MjekgKx5arx7z6Br+1pTT/fE44DgE+CtabEsCdcpFWG
ftC7FdxZabDUhfynSaO43tgKhdVv2XpVobG3iW2RYJOWm2dJSxulZg9+jypdxITm
VX3kPar+mjvwyf3svsGIc65SVaayR6pfiLzV8qBtR3trFRbIlrI7vo21d2tFtuS8
PfAR+9VHkeOdjVKDbu1sl7YycWz03xq4cM9XPFhvrobeFXb5OFwDwLWn4DZR5ZWY
iJSMJkaBSww=
=F6UW
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Arnd Bergmann:
"Four patches for arm-soc this week:
- Kevin Hilman is no longer reachable under his previous email
address. He submitted the patch earlier, but nobody felt
responsible to pick it up.
- One Tegra fix for an incorect register address in device tree.
- IMX multiplatform support exposes a configuration option that leads
to unbootable kernels on all other machines and that needs to
depend on that platform.
- A nontrivial bug fix for the setup of the mxs video output."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: update email address for Kevin Hilman
ARM: tegra: fix register address of slink controller
ARM: imx: add dependency check for DEBUG_IMX_UART_PORT
ARM: video: mxs: Fix mxsfb misconfiguring VDCTRL0
The clock frequency of xxti and xusbxti clocks is dependent on the
frequency of the on-board oscillator that is used to generate these
clocks. So allow the frequency of these clocks to be specfied from
device tree.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
For all supported peripheral controllers on Exynos5440, add clock
lookup information.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
For all supported peripheral controllers on Exynos5250, add clock
lookup information.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
For all supported peripheral controllers on Exynos4 SoCs, add clock
lookup information.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add clock controller nodes for EXYNOS4210, EXYNOS4x12, EXYNOS5250
and EXYNOS5440 SoCs.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=DBFJ
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-3.10' of git://github.com/mripard/linux into next/dt
From Maxime Ripard <maxime.ripard@free-electrons.com>:
Allwinner sunxi DT additions for 3.10
* tag 'sunxi-dt-for-3.10' of git://github.com/mripard/linux:
arm: sunxi: Add clock definitions for the new clock driver
ARM: sunxi: dt: Add support for the PineRiver Mini X-plus
sunxi: a10-cubieboard: Add user LEDs to the device tree
sunxi: a13-olinuxino: Add user LED to the device tree
sunxi: dts: Report the pinctrl nodes as gpio-controllers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This introduces proper clock definitions on sunxi.dtsi, to be used
with the new clock driver for sunxi.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fix typo on register address of slink3 controller where register
address is wrongly set as 0x7000d480 but it is 0x7000d800.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The msm timer binding I wrote is bad. First off, the clock
frequency in the binding for the dgt is wrong. Software divides
down the input rate by 4 to achieve the rate listed in the
binding. We also treat each individual timer as a separate
hardware component, when in reality there is one timer block
(that may be duplicated per cpu) with multiple timers within it.
Depending on the version of the hardware there can be one or two
general purpose timers, status and divider control registers, and
an entirely different register layout.
In the next patch we'll need to know about the different register
layouts so that we can properly check the status register after
clearing the count. The current binding makes this complicated
because the general purpose timer's reg property doesn't indicate
where that status register is, and in fact it is beyond the size
of the reg property.
Clean all this up by just having one node for the timer hardware,
and describe all the interrupts and clock frequencies supported
while having one reg property that covers the entire timer
register region. We'll use the compatible field in the future to
determine different register layouts and if we should read the
status registers, etc.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=s7aA
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman <horms+renesas@verge.net.au>:
Renesas ARM-based SoC updates for v3.10
* tag 'renesas-soc-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (43 commits)
r8a7779: Add Display Unit clock support
ARM: shmobile: R8A7779: use gic_iid() in SATA IRQ resource
ARM: mach-shmobile: r8a7779: add SATA support
ARM: mach-shmobile: r8a7779: SATA DT configuration
ARM: shmobile: r8a7779: add Thermal support on DT
ARM: shmobile: tidyup chip series definition order for r8a7740/r8a7779
ARM: shmobile: r8a7779: use gic_iid macro
ARM: shmobile: r8a7779: fixup DT machine name
ARM: shmobile: r8a7779: fixup dtsi typo
ARM: shmobile: add gic_iid macro for ICCIAR / interrupt ID
ARM: mach-shmobile: r8a7740: Add DT names to clock list
ARM: shmobile: Remove unused hotplug.c
ARM: shmobile: Rearrange r8a7779 cpu hotplug code
ARM: shmobile: Use sh73a0-specific cpu disable code
ARM: shmobile: Update r8a7779 to use scu_power_mode()
ARM: shmobile: Update r8a7779 to check SCU for hotplug
ARM: shmobile: Use R8A7779_SCU_BASE with TWD
ARM: shmobile: Rework SH73A0_SCU_BASE IOMEM() usage
ARM: shmobile: Fix base address readout in headsmp-scu.S
ARM: shmobile: r8a7779: Remove lan from dtsi
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I2C. Also some cleanup of some unneeded properties and conflicting
nodes.
One more DT-only board based on at91rm9200.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRSyP1AAoJEAf03oE53VmQVr4IAJKl8rITnS3rmYYGmFo+cIGl
HkaDM7ljf726hW2bmmcTu1zQLLsdP3EY7qOmuoUN5J8uWSV67Yujc3C0ypqgC2ve
vwWEKuPB8N6utPTWl9eLCvTp+DTKDaq6otfcXFj432tWLWdc0DYKlkaiVfePSChn
hLFFeuIj3XFCIxVJ+Tz14+/b1MC+jswe4TMCvGKE3d4aZ1dgWfS9YhmNjQ0hB1rP
BW0A7RIBW366OUCzvEkKI1NZ8MzKO6ghJMeBpLHuD3I8GJGaF9NhZXi6v7SJVS9i
IdEwXdrYY+TzpllnF9imwhvPK5d6QbcqNVV5Gie+aFwZJTYt4ufPAEIH5rd67jo=
=n+O8
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre <nicolas.ferre@atmel.com>:
DT modifications for at91rm9200 and at91sam9x5 SoCs, mainly around
I2C. Also some cleanup of some unneeded properties and conflicting
nodes.
One more DT-only board based on at91rm9200.
* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
ARM: at91/at91sam9x5cm: add 1-wire chip on CM board
ARM: at91/at91sam9x5ek: i2c1 and i2c2 conflict with macb and lcd
ARM: at91/dt: gpio-keys: remove address-cells and size-cells properties
ARM: at91: add MPA 1600 DT board
ARM: at91: add pinctrl nodes to i2c-gpio on RM92000 DT
ARM: at91: add TWI bindings to RM9200 DT
ARM: at91: dt: at91sam9x5: add i2c-gpio pinctrl
ARM: at91: dt: at91sam9x5: add i2c pinctrl
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This add the 1-wire chip present on the CM board to the DTS.
As the pin is also used by leds, it's disabled by default.
If the board really wants it, it can be enabled in the board DTS.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
On at91sam9x5ek, macb0 is enabled, so it conflicts with i2c2 (PB4)
same for i2c1, (conflicts with LCD).
Moreover, only i2c0 is used on this board.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Gpio-keys nodes are not using the "reg" property in their sub nodes.
So, there is no need to define #address-cells and #size-cells properties
in gpio-keys nodes: we remove them.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
[nicolas.ferre@atmel.com: remove unneeded address-cells and size-cells to gpio-keys]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
GPIO pins used by i2c-gpio must be set to multi drive
(open drain) to work properly.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
i2c-gpio is sometimes used in place of i2c-at91.
This adds the pin muxes for the gpios.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This adds the at19 i2c controller pin muxes for at91sam9x5 based boards.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fix several device-tree bindings, that haven't been updated for newest
versions of respective drivers, and device names and pin numbers, left over
from non-DT and old pinctrl versions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
To avoid having to repeat common DT node properties in all .dts files
move them to SoC's .dtsi file, setting their status to "disabled."
Individual boards will pick up devices, that they want to use and
change their DT node status to enabled.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
kzm9g supplies 3.3V to its SDHI0 and SDHI2 interfaces. Specifying 2.8V
prevents some (e.g. certain SDIO) cards from working. This patch fixes the
voltage and removes redundant OCR masks from platform data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
atlas6.dtsi is basically a copy of prima2.dtsi as most components are
compatible with prima2 except that:
1. node of l2 cache is deleted
2. node multimedia engine is deleted
3. node of sata is deleted
4. node of sdmmc4 is deleted
5. powervr is moved to "powervr,sgx510"
6. pinctrl is moved to atlas6 as pinmux layout has big changes in
atlas6
7. clock is moved to atlas6 as clock layout has changes in atlas6
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Jiansong Chen <Jiansong.Chen@csr.com>
Things are calming down for arm-soc as well. This set of bug fixes is
dominated in size by the at91 platform bug fixes. Some of them were
meant to go through the framebuffer tree during the merge window, but
since the framebuffer maintainer could not be reached, I offered to
take them here. The other notable at91 change is the addition of pinctrl
definitions to fix the NAND controller.
The rest are mostly simple regression fixes:
* Our removal of VIRT_TO_BUS conflicted with Stephen Rothwell's
renaming of the Kconfig symbol. You will get a trivial merge conflict
here, we still want to remove it.
* missing bits for clocks on imx and s5pv210
* missing header inclusions in mmp and shmobile
* typos in s5pv210 camera and vt8500 clock support code
and three trivial fixes for pre-3.8 bugs:
* an old bogus build warning in the joystick driver
* a misleading Kconfig description
* a NULL pointer check on davinci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=oLKI
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Arnd Bergmann:
"Things are calming down for arm-soc as well. This set of bug fixes is
dominated in size by the at91 platform bug fixes. Some of them were
meant to go through the framebuffer tree during the merge window, but
since the framebuffer maintainer could not be reached, I offered to
take them here. The other notable at91 change is the addition of
pinctrl definitions to fix the NAND controller.
The rest are mostly simple regression fixes:
- Our removal of VIRT_TO_BUS conflicted with Stephen Rothwell's
renaming of the Kconfig symbol. You will get a trivial merge
conflict here, we still want to remove it.
- missing bits for clocks on imx and s5pv210
- missing header inclusions in mmp and shmobile
- typos in s5pv210 camera and vt8500 clock support code
and three trivial fixes for pre-3.8 bugs:
- an old bogus build warning in the joystick driver
- a misleading Kconfig description
- a NULL pointer check on davinci"
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: fix CONFIG_VIRT_TO_BUS handling
ARM: i.MX35: enable MAX clock
ARM: Scorpion is a v7 architecture, not v6
ARM: mmp: add platform_device head file in gplugd
input/joystick: use get_cycles on ARM
[media] s5p-fimc: fix s5pv210 build
clk: vt8500: Fix "fix device clock divisor calculations"
ARM: i.MX25: Fix DT compilation
ARM: at91: fix infinite loop in at91_irq_suspend/resume
ARM: at91: add gpio suspend/resume support when using pinctrl
ARM: at91: fix LCD-wiring mode
atmel_lcdfb: fix 16-bpp modes on older SOCs
ARM: at91: dt: at91sam9x5: complete NAND pinctrl
ARM: at91: dt: at91sam9x5: correct NAND pins comments
ARM: davinci: edma: fix dmaengine induced null pointer dereference on da830
ARM: shmobile: marzen: Include mmc/host.h
ARM: EXYNOS: Add #dma-cells for generic dma binding support for PL330
ARM: S5PV210: Fix PL330 DMA controller clkdev entries
Add SDHI0 and SDHI2 interfaces to kzm9g-reference. With no pinctrl DT
support we cannot use GPIO card-detection and regulator switching.
Also update the MMCIF DT node to use all 8 data lines and avoid
redundant information in DT.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
[ horms+renesas@verge.net.au: Updated for pinmux changes by Laurent Pinchart ]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Provide alternate board code for the kzm9g to demonstrate
how DT may be used given the current state of driver
device tree support. This is intended to act as a reference
for mach-shmobile developers.
Some notes:
* Brings up the GIC interrupt handler using device tree
* Brings up the following device using device tree:
- MMCIF (MMC)
* Does not bring up the INTC interrupt controller at all,
thus external devices may not be used. In particular,
the SMSC ethernet device may not be used and thus
NFS root may not be used.
* Uses existing C code and not device tree to initialise the following,
which are needed for a working board:
- SCIF (Serial)
- CMT (Clock)
- PFC (GPIO)
To use this alternate board code instead of the normal board code,
CONFIG_MACH_KZM9G_REFERENCE should be selected in the kernel config.
And the sh73a0-kzm9g-reference.dtb flattened device tree blob should be used.
Includes fix by Thierry Reding to no longer use gic_handle_irq()
Includes fixes by Guennadi Liakhovetski for recent pinmux changes.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Provide alternate board code for the marzen to demonstrate
how DT may be used given the current state of driver
device tree support. This is intended to act as a reference
for mach-shmobile developers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
With this one we have:
- An ab8500 build failure fix.
- An ab8500 device tree parsing fix.
- A fix for twl4030_madc remove routine to work properly (when built-in).
- A fix for properly registering palmas interrupt handler.
- A fix for omap-usb init routine to actually write into the hostconfig
register.
- A couple of warning fixes for ab8500-gpadc and tps65912.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=XFgy
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-fixes
Pull MFD fixes from Samuel Ortiz:
"This is the first batch of MFD fixes for 3.9.
With this one we have:
- An ab8500 build failure fix.
- An ab8500 device tree parsing fix.
- A fix for twl4030_madc remove routine to work properly (when
built-in).
- A fix for properly registering palmas interrupt handler.
- A fix for omap-usb init routine to actually write into the
hostconfig register.
- A couple of warning fixes for ab8500-gpadc and tps65912"
* tag 'mfd-fixes-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-fixes:
mfd: twl4030-madc: Remove __exit_p annotation
mfd: ab8500: Kill "reg" property from binding
mfd: ab8500-gpadc: Complain if we fail to enable vtvout LDO
mfd: wm831x: Don't forward declare enum wm831x_auxadc
mfd: twl4030-audio: Fix argument type for twl4030_audio_disable_resource()
mfd: tps65912: Declare and use tps65912_irq_exit()
mfd: palmas: Provide irq flags through DT/platform data
mfd: Make AB8500_CORE select POWER_SUPPLY to fix build error
mfd: omap-usb-host: Actually update hostconfig
Two more for fixing PM suspend/resume IRQ on AIC5 and
GPIO used with pinctrl.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRQYyVAAoJEAf03oE53VmQsz0IAMfjyOwqbuKmSwjV6HZAsu/k
/p8MB6F5Fg4PuBsPim+F8/kIWYuxSH/H17nwdA9fgWt6E8Z0zFtfbqvQkaTxWI/K
HWLZh6Z4ZHalDBInl1bTJ+mzMH2EaIZmJDZF7uOsE5EJz9b+tMzSZbaWWLllFwvQ
mSMidkg0x9fSI7GAoO7x/uxDPV5TdU2pSw5rFUfAIURXlGX1OVE9/Mpy9Utmmlax
3af3C2FgnlSLaVTHUv7dnefaSkBTJNFb0kydn7sgNa0tIRj2/pfG+xeXV+pEB92Y
UhNKS850DyAyWgBBxckQuUnin2v3snMazfbRiKbBGFnGlbIomDdFhpNu7ynRvfc=
=9r9y
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
From Nicolas Ferre <nicolas.ferre@atmel.com>:
Two patches for Device Tree on at91sam9x5/NAND.
Two more for fixing PM suspend/resume IRQ on AIC5 and
GPIO used with pinctrl.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: fix infinite loop in at91_irq_suspend/resume
ARM: at91: add gpio suspend/resume support when using pinctrl
ARM: at91: dt: at91sam9x5: complete NAND pinctrl
ARM: at91: dt: at91sam9x5: correct NAND pins comments
Includes an update to -rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There was only chip enable and readdy/busy pins for the nand controller.
This add the rest of the pins.
pinctrl_nand_16bits contains the specific muxes for 16 bits NANDs.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Comments on NAND pins where inverted.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Change cpts_active_slave to active_slave so that the same DT property
can be used to ethtool and SIOCGMIIPHY.
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow configuration of the r8a7779 SoC SATA controller using a flattened device
tree.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
76cc188749
(thermal: rcar: add Device Tree support)
supported rcar_thermal DT probing.
rcar thermal driver doesn't support IRQ on r8a7779 chip
since it is using old design IRQ.
R-Car/R-Mobile next generation chips are using new design IRQ,
and rcar thermal driver is supporting these.
This patch adds rcar_thermal DT support for r8a7779 without IRQ.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
r8a7779 is not r8a7740 chip
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The ethernet controller is not part of the r8a7779 SoC.
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Allow a minimal setup of the r8a7779 SoC using a flattened device tree.
In particular, configure the i2c and ethernet controllers using a
flattened device tree.
SCI serial controller and TMU clock source, whose drivers do not yet
support configuration using a flattened device tree, are still configured
using C code in order to allow booting of a board with this SoC.
The ethernet controller also requires a regulator which is a board property.
A sample snippet DT for the marzen board is as follows:
/dts-v1/;
/include/ "r8a7779.dtsi"
/ {
fixedregulator3v3: fixedregulator@0 {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
};
&lan0 {
vddvario-supply = <&fixedregulator3v3>;
vdd33a-supply = <&fixedregulator3v3>;
};
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This allows the GIC interrupt controller of the r8a7779 SoC to be
initialised using a flattened device tree blob.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v3
* Fix copy-paste error and use unique reg values for each CPU
v2
As suggested by Mark Rutland
* Add reg and device_type to cpus
* Remove #address-cells from gic
This replaces an earlier patch from Viresh Kumar to move
the spear platform over to the generic DMA binding. This
version is now based on the merged multiplatform capable
spear platform, rather than the separate spear13xx/3xx/6xx
directories.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vinod Koul <vinod.koul@linux.intel.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: spear-devel@list.st.com
Add a device tree node to instantiate the dove thermal driver.
Enable the driver and the thermal framework in dove_defconfig.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Kirkwood 88F6282 and 88F6283 have a thermal sensor.
This patch adds a DT node and enables the driver in the kernel config.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Globalscale Mirabox platform can be connected to the JTAG/GPIO box
through the Multi-IO port. The GPIO box use the NXP PCA9505 I/O port
expansion IC to provide 40-bit parallel input/output GPIOs. This patch
enable the use of this expander on the Mirabox.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ab8500 device is a child of the prcmu device, which is a memory mapped
bus device, whose children are addressable using physical memory addresses,
not using mailboxes, so a mailbox number in the ab8500 node cannot be
parsed by DT. Nothing uses this number, since it was only introduced
as part of the failed attempt to clean up prcmu mailbox handling, and
we can simply remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The BCM2835 has a single instance of the "SPI0"-type SPI master
controller. Instantiate it in the SoC .dtsi file, Don't enable it in
the Raspberry Pi board .dts file, since we have no idea what is actually
connected, and hence no idea what to set the bus clock rate to.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
This patch adds #dma-cells property to PL330 DMA controller nodes for
supporting generic dma dt bindings on SOCFPGA platform. #dma-channels
and #dma-requests are not required now but added in advance.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The first four patches:
89c58c1 rtc: rtc-mv: Add support for clk to avoid lockups
de88747 gpio: mvebu: Add clk support to prevent lockup
7bf5b40 ARM: kirkwood: fix to retain gbe MAC addresses for DT kernels
93fff4c ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency
are Cc'd to stable since they were held over from the previous merge window.
The rest are a small collection of fixes and a couple of devicetree conversion
catchups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJROmXfAAoJEAi3KVZQDZAeahAIAIWybkKuD/lKLRPU3FmS59gM
gdcPxQcjFnldRRBQFXRfSQ4acFNEWZwDgHXs0gpKsUCoZ2w/tCbjba0sNb2vWsmc
H4Nh8MU3CqHIuGDFSmsbDHX0BNrp6JvZLxiY7vtswTDqZt1K/UKb7obnnbAo8ygu
OtbGItfYNTjMJ0B1Ar2eYCoA4V29SFzXB+ymWEHl4u9Vmwasr0uervjHhyq+3tU1
pCNPWc98N9r0VqniVbbTqVuwlwoc3IZmbiv1T9EGMw2PDbtcIJLwY7oxlSb0kW3e
QIookCxlItX1A360TmGI4xKnSRR42ZinNmn2AuLetW8ydnRNDwkyrRJZ2VsbQLE=
=mme/
-----END PGP SIGNATURE-----
Merge tag 'mvebu_fixes_for_v3.9' of git://git.infradead.org/users/jcooper/linux into fixes
mvebu fixes for v3.9 from Jason Cooper <jason@lakedaemon.net>:
The first four patches:
89c58c1 rtc: rtc-mv: Add support for clk to avoid lockups
de88747 gpio: mvebu: Add clk support to prevent lockup
7bf5b40 ARM: kirkwood: fix to retain gbe MAC addresses for DT kernels
93fff4c ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency
are Cc'd to stable since they were held over from the previous merge window.
The rest are a small collection of fixes and a couple of devicetree conversion
catchups.
* tag 'mvebu_fixes_for_v3.9' of git://git.infradead.org/users/jcooper/linux:
arm: mach-orion5x: fix typo in compatible string of a .dts file
arm: mvebu: fix address-cells in mpic DT node
arm: plat-orion: fix address decoding when > 4GB is used
arm: mvebu: Reduce reg-io-width with UARTs
ARM: Dove: add RTC device node
arm: mvebu: enable the USB ports on Armada 370 Reference Design board
ARM: dove: drop "select COMMON_CLK_DOVE"
rtc: rtc-mv: Add support for clk to avoid lockups
gpio: mvebu: Add clk support to prevent lockup
ARM: kirkwood: fix to retain gbe MAC addresses for DT kernels
ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The PMC HW is not 100% compatible across all Tegra series. We need to
specify them in DT.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The new clockframework introduced DT IDs for each clock. To be able to remove
the device registrations, this driver needs to be updated to use the DT IDs.
Note that the actual removal of the clk_register_clkdev() calls will be done
in a later series.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The GPIO pin of SD slot card detection should active low.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This board comes with an Allwinner A10, two external USB ports, a SD
Card reader, 1GB of RAM, the usual video connectors and an onboard wifi
chip.
Of course, the support is quite minimal for now...
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add MCT device tree node for Exynos4210, Exynos4212, Exynos4412
and Exynos5250.
Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The orion5x-lacie-ethernet-disk-mini-v2.dts file was using
"marvell-orion5x-88f5182" as a compatible string, while it should have
been "marvell,orion5x-88f5182".
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
There is no need to have a #address-cells property in the MPIC Device
Tree node, and more than that, having it confuses the of_irq_map_raw()
logic, which will be used by the Marvell PCIe driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Setting the reg-io-width to 1 byte represents more accurate
description of the HW.
This will fix an issue where UART driver causes kernel
panic during bootup. Gregory CLEMENT traced the issue to
autoconfig() in 8250.c, where the existence of FIFO is
checked from UART_IIR register. The register is now read as
32-bit value as the reg-io-width is set to 4-bytes. The
retuned value seems to contain bogus data for bits 31:8,
causing the issue.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The commit:
48be9ac ARM: Dove: split legacy and DT setup
removed the RTC initialization. This patch re-enables the RTC
via the DT.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch modifies the Armada 370 Reference Design DTS file to enable
support for the two USB ports found on this board.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the
driver clk_prepare_enable() this clock, otherwise there is a danger
the SoC will lockup when accessing RTC registers with the clock
disabled.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The kirkwood SoC GPIO cores use the runit clock. Add code to
clk_prepare_enable() runit, otherwise there is a danger of locking up
the SoC by accessing the GPIO registers when runit clock is not
ticking.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When DT support for kirkwood was first introduced, there was no clock
infrastructure. As a result, we had to manually pass the
clock-frequency to the driver from the device node.
Unfortunately, on kirkwood, with minimal config or all module configs,
clock-frequency breaks booting because of_serial doesn't consume the
gate_clk when clock-frequency is defined.
The end result on kirkwood is that runit gets gated, and then the boot
fails when the kernel tries to write to the serial port.
Fix the issue by removing the clock-frequency parameter from all
kirkwood dts files.
Booted on dreamplug without earlyprintk and successfully logged in via
ttyS0.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The exynos5250 based chromebooks have a max77686 pmic on i2c channel 0.
Add support for the pmic in the common cros5250 dts file.
Tested after enabling cpufreq support for exynos5250 SoC and varying the
arm frequency/voltage using the userspace governer.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds device tree nodes for MFC and G-scaler power
domains of exynos5250.It binds these power-domain nodes to repsective
device tree nodes
It also adds support to enable PM generic domains for exynos5250.
Signed-off-by: Prasanna Kumar <prasanna.ps@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adding OHCI device tree node for Exynos5250 along with
the device base address.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adding EHCI device tree node for Exynos5250 along with
the device base adress and gpio line for vbus.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add device tree node for DP controller in EXYNOS5250 and
enable the instance for the SMDK5250 board.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch enables RTC device node defined in exynos4.dtsi for
exynos4412-odroidx.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This fixes the property of dw-mshc-sdr-timing and dw-mshc-ddr-timing as per
its current binding, it only has two cells.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Arndale is a low cost board based on the Samsung Exynos5250 SoC.
This patch adds initial device tree support for this board.
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds timer node and re-organizes cpu node for exynos5440.
Acked-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes disabled status from I2C node for exynos5440-ssdk5440,
and fixes the incorrect compatible property value of i2c for exynos5440.
Signed-off-by: Giridhar Maruthy <giridhar.m@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add initial DT for Hardkernel's ODROID-X board based on EXYNOS4412
SoC. This patch including adds the node to support fixed voltage for
peripherals like LED, ethernet controller, and this patch adds GPIO
connected LEDS on ODROID-X board and configure its properties like
following:
LED1: use 'heartbeat' trigger, blinking while the board is running.
LED2: use 'mmc0' trigger, on when mmc0 is accessing.
And adds the device node to support eMMC storage on SDCARD4 ports,
controlled by MSHC.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Acked-by: Olof Johansson <olof@lixom.net>
[kgene.kim@samsung.com: squashed into one commit as per Olof's comment]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add a minimal board dts file for EXYNOS4412 based Insignal Origen board.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add gpio offset into "gpio-range-cells" property. It's used to support
sparse pinctrl range in gpio chip.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds #dma-cells property to PL330 DMA controller
nodes for supporting generic dma dt bindings on samsung exynos
platforms. #dma-channels and #dma-requests are not required now
but added in advance.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cubieboard has two LEDs available for use, a blue one (labeled LED1)
and a green one (labeled LED2).
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- move early resume code out of .data section to fix allyesconfig
failure since c08e20d (arm: Add v7_invalidate_l1 to cache-v7.S)
gets merged
- Fix incorrect DISP1_DAT_21 number in imx53-mba53 disp1-grp1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRND3rAAoJEFBXWFqHsHzOL2cH/je/02JztrorpD2k76mQLjo4
2hjfUwpYNvwEpwBCXo5NnDv5I4XrkJdHs7O2CHmigQOpDYSvq9qx3VcPQ0BX8cWU
3Qqb9tiglNsvD2NuxUYmG2CHFpGLp+lK3unkA/ZDXM2apjbacL1/wTgU81uthDwY
SLBBS7hSlBvuPdxoeIBeuOOBYnhbdaZCutgFVTF8rRT6RHmYjekga6OqF32Vp/og
Gxw50cj+smdW6wr1Na0zQJfMHTkm5hJ9s9iYHAbYNZplpl8VZJQAaCWgZhihZJYI
XULUCR0s8DLLUgj4IUgJS3Kc35G/2M1ovhxyw3hqDzOt+Miy8m4eYh21BL2iS8w=
=V76T
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
The imx fixes for 3.9:
- move early resume code out of .data section to fix allyesconfig
failure since c08e20d (arm: Add v7_invalidate_l1 to cache-v7.S)
gets merged
- Fix incorrect DISP1_DAT_21 number in imx53-mba53 disp1-grp1
* tag 'imx-fixes-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx53-mba53: fix fsl,pins for disp1-grp1
ARM: mach-imx: move early resume code out of the .data section
Signed-off-by: Olof Johansson <olof@lixom.net>
As DT support for clocks and smp_twd is enabled, add clock entry
for smp_twd clock to DT.
This fixes the following error while booting the kernel:
smp_twd: clock not found -2
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: include kernel log spew that this fixes]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
BCM2835-ARM-Peripherals.pdf states that the I2C module's input clock is
nominally 150MHz, and that value is currently reflected in bcm2835.dtsi.
However, practical measurements show that the rate is actually 250MHz,
and this agrees with various downstream kernels.
Switch the I2C clock's frequency to 250MHz so that the generated bus
clock rate is accurate.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
According to fsl,imx53-pinctrl.txt, the pin number of DISP1_DAT_21
should be 545, while 543 is IPU_CSI0_D_3. Along with the change,
one duplication of DISP1_DAT_0 in disp1-grp1 is removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The AB8500 GPIO driver has been un-BROKEN and rewritten as a pinctrl
driver. Now that it's back in use, let's ensure that it's available
when booting Snowball with Device Tree enabled.
Cc: arm@kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AB8500 GPIO driver has been un-BROKEN and rewritten as a pinctrl
driver. Now that it's back in use, let's ensure that it's available
when booting HREF with Device Tree enabled.
Cc: arm@kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO controlled MMCI regulator used on the ux5x0 boards takes
100us to settle. There's already a binding to provide such
information. Let's make use of it.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Correct a typo in the Device Tree source file, where instead of
specifying property 'enable-gpio', which the driver is expecting
we specified 'gpio-enable' instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In an effort to move platform specific GPIO controlled regulators
out from platform code we've created a new mechanism to specify
them from within the MMCI driver using the supply name 'vmmc-ios'.
For that to happen when booting device tree, we need to supply it
in the MMCI (SDI) node.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If not specified, the GPIO control bit is inverted by default i.e.
low-enable and high-disable. This is not the case with the MMCI
regulator, hence it will turn on during a disable and off when
regulator_enable() is invoked.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Correct the voltage specified by the mmci regulator node in Device
Tree. Despite the MMC subsystem insisting on v3.3, we actually only
offer v2.9, and not v2.6 which must have actually been a typo.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently we only include the PRCMU's primary registers when
referencing the register count in the 'reg' property. This patch
expands that count to include the secure registers also.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the STMPE IRQ is triggered to be active high level-sensitive, the
Nomadik GPIO controller it uses complains, although it still works.
Recently we attempted to move triggering to low-to-high in an attempt
to prevent the warning; however, this ensured that the IRQ was actually
missed completely. Now we have a solution which both works and keeps the
GPIO controller happy.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This series contains changes for the Marvell EBU platforms (mvebu,
orion, kirkwood, dove) that were not part of the first set of pull
requests because of dependencies on the MMC tree, and being submitted
a little late.
Notable changes are:
* More devices get moved out of board files into device tree
descriptions. The remaining devices listed in there have patches
that will get sent for 3.10, after which we can remove a lot of the
board files entirely. We are doing the pinctrl and mmc drivers here,
ethernet and PCI still remain.
* SMP support for mvebu is improved with support for the
local interrupt controller.
* The Guruplug board file gets replaced with a DT description.
Unfortunately, the dependency on the MMC tree turned out to be a much
larger problem than expected, when the MMC maintainer rebased the patches
in his tree that all of the patches in this branch are based on, which
caused merge conflicts between the new and old versions of those patches.
To work around the merge conflicts, this branch rebases all patches
on top of the respective MMC patches that did get merged into 3.9.
The patches are all identical to the versions that were part of
linux-next, but have a new commit date.
Merge conflicts:
* in board-nsa310.c, the gpio.h inclusion was removed prematurely and
put back as a bug fix earlier. With this series it is really not needed
any more.
* The patch to add rtc support was already applied by Andrew Morton,
and conflicts with a second copy that was in this series, which adds
a lot of other devices to arch/arm/boot/dts/armada-370-xp.dtsi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7l0+
-----END PGP SIGNATURE-----
Merge tag 'late-mvebu-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC mvebu platform changes from Olof Johansson:
"This series contains changes for the Marvell EBU platforms (mvebu,
orion, kirkwood, dove) that were not part of the first set of pull
requests because of dependencies on the MMC tree, and being submitted
a little late.
Notable changes are:
- More devices get moved out of board files into device tree
descriptions. The remaining devices listed in there have patches
that will get sent for 3.10, after which we can remove a lot of the
board files entirely. We are doing the pinctrl and mmc drivers
here, ethernet and PCI still remain.
- SMP support for mvebu is improved with support for the local
interrupt controller.
- The Guruplug board file gets replaced with a DT description.
Unfortunately, the dependency on the MMC tree turned out to be a much
larger problem than expected, when the MMC maintainer rebased the
patches in his tree that all of the patches in this branch are based
on, which caused merge conflicts between the new and old versions of
those patches.
To work around the merge conflicts, this branch rebases all patches on
top of the respective MMC patches that did get merged into 3.9. The
patches are all identical to the versions that were part of
linux-next, but have a new commit date."
* tag 'late-mvebu-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (90 commits)
arm: mvebu: enable the SD card slot on Armada 370 Reference Design board
ARM: kirkwood: topkick: init mvsdio via DT
ARM: kirkwood: nsa310: convert to pinctrl
ARM: Kirkwood: topkick: Enable i2c bus.
ARM: kirkwood: topkick: convert to pinctrl
ARM: dove: convert serial DT nodes to clocks property
arm: mvebu: Add SPI flash on Armada 370 DB board
arm: mvebu: Add SPI flash on Armada XP-DB board
arm: mvebu: Add SPI flash on Armada XP-GP board
arm: mvebu: Add support for SPI controller in Armada 370/XP
clocksource: update and move armada-370-xp-timer documentation to timer directory
arm: mvebu: update DT to support local timers
ARM: Dove: convert usb host controller to DT
arm: mvebu: Enable USB controllers on Armada 370/XP boards
arm: mvebu: Add support for USB host controllers in Armada 370/XP
arm: mvebu: add button for OpenBlocks AX3-4
ARM: Kirkwood: Convert NS2 to gpio-poweroff.
ARM: Kirkwood: Convert NSA310 I2C to device tree
ARM: Kirkwood: Convert NSA310 to use gpio-poweroff driver
ARM: Kirkwood: Convert NSA310 to DT based regulators.
...
This branch contains changes for OMAP that came in late during the release
staging, close to when the merge window opened.
It contains, among other things:
- OMAP PM fixes and some patches for audio device integration
- OMAP clock fixes related to common clock conversion
- A set of patches cleaning up WFI entry and blocking.
- A set of fixes and IP block support for PM on TI AM33xx SoCs (Beaglebone, etc)
- A set of smaller fixes and cleanups around AM33xx restart and revision
detection, as well as removal of some dead code (CONFIG_32K_TIMER_HZ)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=/vBT
-----END PGP SIGNATURE-----
Merge tag 'late-omap' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late OMAP changes from Olof Johansson:
"This branch contains changes for OMAP that came in late during the
release staging, close to when the merge window opened.
It contains, among other things:
- OMAP PM fixes and some patches for audio device integration
- OMAP clock fixes related to common clock conversion
- A set of patches cleaning up WFI entry and blocking.
- A set of fixes and IP block support for PM on TI AM33xx SoCs
(Beaglebone, etc)
- A set of smaller fixes and cleanups around AM33xx restart and
revision detection, as well as removal of some dead code
(CONFIG_32K_TIMER_HZ)"
* tag 'late-omap' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: omap2: include linux/errno.h in hwmod_reset
ARM: OMAP2+: fix some omap_device_build() calls that aren't compiled by default
ARM: OMAP4: hwmod data: Enable AESS hwmod device
ARM: OMAP4: hwmod data: Update AESS data with memory bank area
ARM: OMAP4+: AESS: enable internal auto-gating during initial setup
ASoC: TI AESS: add autogating-enable function, callable from architecture code
ARM: OMAP2+: hwmod: add enable_preprogram hook
ARM: OMAP4: clock data: Add missing clkdm association for dpll_usb
ARM: OMAP2+: PM: Fix the dt return condition in pm_late_init()
ARM: OMAP2: am33xx-hwmod: Fix "register offset NULL check" bug
ARM: OMAP2+: AM33xx: hwmod: add missing HWMOD_NO_IDLEST flags
ARM: OMAP: AM33xx hwmod: Add parent-child relationship for PWM subsystem
ARM: OMAP: AM33xx hwmod: Corrects PWM subsystem HWMOD entries
ARM: DTS: AM33XX: Add nodes for OCMC RAM and WKUP-M3
ARM: OMAP2+: AM33XX: Update the hardreset API
ARM: OMAP2+: AM33XX: hwmod: Update the WKUP-M3 hwmod with reset status bit
ARM: OMAP2+: AM33XX: hwmod: Fixup cpgmac0 hwmod entry
ARM: OMAP2+: AM33XX: hwmod: Update TPTC0 hwmod with the right flags
ARM: OMAP2+: AM33XX: hwmod: Register OCMC RAM hwmod
ARM: OMAP2+: AM33XX: CM/PRM: Use __ASSEMBLER__ macros in header files
...
This branch contains of devicetree changes for the Freescale i.MX platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process since
every line of the file is touched.
On top of that are a handful of the regular changes; enabling more boards
as DT-based instead of legacy board files (mx25pdk), enabling another
driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other platforms
in the future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=72aL
-----END PGP SIGNATURE-----
Merge tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC i.MX DT changes from Olof Johansson:
"This branch contains of devicetree changes for the Freescale i.MX
platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process
since every line of the file is touched.
On top of that are a handful of the regular changes; enabling more
boards as DT-based instead of legacy board files (mx25pdk), enabling
another driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other
platforms in the future."
* tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: dts: add dtsi for imx6q and imx6dl
ARM: dts: rename imx6q.dtsi to imx6qdl.dtsi
ARM: dts: i.MX6: Add regulator delay support
ARM: dts: Add device tree entry for onewire master on i.MX53
ARM: i.MX53: Add clocks for i.mx53 onewire master.
W1: Add device tree support to MXC onewire master.
ARM: imx: enable imx6q-cpufreq support
ARM: dts: Add apf51 basic support
ARM i.MX6: change mxs usbphy clock usage
ARM: dts: imx6q: Remove silicon version from SDMA firmware
ARM i.MX53: dts: add oftree for MBa53 baseboard
ARM i.MX53: add dts for the TQ tqma53 module
ARM: dts: imx53: pinctrl update
ARM i.MX51 babbage: Add keypad support
ARM: dts: imx: Add imx51 KPP entry
ARM: dts: imx25-karo-tx25: Put status entry in the end
ARM: mx25pdk: Add device tree support
ARM: dts: imx: use nodes label in board dts
ARM: dts: add missing imx dtb targets
ARM: boot: dts: Add an entry for imx27-pdk.dtb
...
The Armada 370 Reference Design board has one SD card slot, directly
connected to the SDIO IP of the SoC, so we enable this IP. there are no
GPIOs for card-detect and write-protect so we do not specify any.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
of_serial now has support for using clocks property and we have
a DT clock provider. This patch replaces the hard coded clock-frequency
property with a clocks phandle to tclk.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch add support for the SPI flash MX25l25635E which is present
on the Armada 370 DB board. This flash stores the bootloader and its
environment.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch add support for the SPI flash M25P64 which is present on
the Armada XP DB board. This flash stores the bootloader and its
environment.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds an SPI master device node for Armada XP-GP board.
This master node is an SPI flash controller 'n25q128a13'.
Since there is no 'partitions' node declared, one full sized
partition named as the device will be created.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Tested-by: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 370 and Armada XP SoC has an SPI controller.
This patch adds support for this controller in Armada 370
and Armada XP SoC common device tree files.
Note that the Armada XP SPI register length is 0x50 bytes,
while Armada 370 SPI register length is 0x28 bytes,
so we choose the smaller of the two.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Acked-by: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the time-armada-370-xp support local timers, updated the
device tree to take it into account.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With DT support for orion-ehci also convert Dove to it and
remove the legacy calls and clock aliases.
This patch is based on "ARM: Dove: split legacy and DT setup"
applied to mvebu/boards recently.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch activates every USB port provided by each SoC.
Except for Armada XP Openblocks AX3-4 board,
where we enable only the first two USB ports
until we have more information on the third one usage.
Cc: Lior Amsalem <alior@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 370 and Armada XP SoC has an Orion EHCI USB controller.
This patch adds support for this controller in Armada 370
and Armada XP SoC common device tree files.
Cc: Lior Amsalem <alior@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The OpenBlocks AX3-4 board has one software-controlled button on the
front side, labeled "INIT", so we add minimal support for this button
in the kernel.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Remove C code and add a Device Tree node in its place.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add a sub-node into the I2C node to represent the adt7476 device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Remove the C code and add a Device Tree node for gpio-poweroff.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
CuBox needs to enable USB power on a gpio pin. Add a fixed regulator
to always enable usb power on boot.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
gpio-leds has support for pinctrl allocation, make use of it.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The 88f6282 has one more TWSI(TWSI1). This add the information to enable
pinctl of TWSI1.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds a pinmux option, pmx_sdio, to enable the muxing of
the SDIO interface on the 88F6282 SoC from Marvell.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the mvsdio driver has a Device Tree binding, and the SDIO
controller is declared in kirkwood.dtsi, migrate the mplcec4 board to
use the Device Tree to probe the SDIO controller and to mux the pins
of the SDIO interface correctly.
This patch has not been tested, it remains to be tested by a person
having access to the hardware.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Stefan Peter <s.peter@mpl.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the mvsdio driver has a Device Tree binding, and the SDIO
controller is declared in kirkwood.dtsi, migrate the dreamplug board
to use the Device Tree to probe the SDIO controller and to mux this
interface properly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the SDIO controller has a Device Tree binding, let's use it
in kirkwood.dtsi.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Globalscale Mirabox uses the SDIO interface of the Armada 370 to
connect to a Wifi/Bluetooth SD8787 chip, so we enable the SDIO
interface of this board in its Device Tree file.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP DB evaluation board has one SD card slot, directly
connected to the SDIO IP of the SoC, so we add a device tree
description for it.
However, in the default configuration of the board, the SD card slot
is not usable: the connector plugged into CON40 must be changed
against a different one, provided with the board by the
manufacturer. Since such a manual modification of the hardware is
needed, we did not enable the SDIO interface by default, and left it
to the board user to modify the Device Tree if needed. Since this
board is really only an evaluation board for developers and not a
final product, it is not too bad.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP DB evaluation board has one SD card slot, directly
connected to the SDIO IP of the SoC, so we enable this
IP. Unfortunately, there are no GPIOs for card-detect and
write-protect.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The SDIO interface is only available on pins MPP30/31/32/33/34/35 on
the various Armada XP variants, so we provide a pin muxing option for
this in the Armada XP .dtsi files.
Even though those muxing options are the same for MV78230, MV78260 and
MV78460, we keep them in each .dtsi file, because the number of pins,
and therefore the declaration of the pinctrl node, is different for
each SoC variant.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The SDIO interface is available either on pins MPP9/11/12/13/14/15 or
MPP47/48/49/50/51/52 on the Armada 370. Even though all combinations
are potentially possible, those two muxing options are the most
probable ones, so we provide those at the SoC level .dtsi file.
In practice, in turns out the Armada 370 DB board uses the former,
while the Armada 370 Mirabox uses the latter.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the mvsdio MMC driver has a Device Tree binding, we add the
Device Tree informations to describe the SDIO interface available in
the Armada 370/XP SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 370 and Armada XP Socs have the same controller that the
one used in the orion platforms. This patch updates the device tree
for these SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Abraham