This adds support for enabling automatic clockgating on nvidia GPUs for
Kepler1. While this is not technically a clockgating level, it does
enable clockgating using the clockgating values initially set by the
vbios (which should be safe to use).
This introduces two therm helpers for controlling basic clockgating:
nvkm_therm_clkgate_enable() - enables clockgating through
CG_CTRL, done after initializing the GPU fully
nvkm_therm_clkgate_fini() - prepares clockgating for suspend or
driver unload
A lot of this code was originally going to be based off of fermi;
however it turns out that while Fermi's the first line of GPUs that
introduced this kind of power saving, Fermi requires more fine tuned
control of the CG_CTRL registers from the driver while reclocking that
we don't entirely understand yet.
For the simple parts we will be sharing with Fermi for certain however,
we at least add those into a new subdev/therm/gf100.h header.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We've still been directly using the legacy crtc gamma_set() hook even
after conversion to atomic modesetting.
For userspace clients this was fine, however, fbcon will use the atomic
property when it's running on an atomic driver, which means we miss its
colormap updates - which is particularly bad for 8bpp framebuffers!
This commit converts the driver to use the atomic property + the helper
function implementing the legacy hook on top of atomic.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80675
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
For some reason forgotten by history, we've been using a 1025-entry LUT
mode, and sparsely filling it with the 256-entry LUT we're handed.
Until we land support for the full atomic colour management properties,
this commit switches to using the 257-entry mode to fix colour mapping
with depth 30 framebuffers.
Reported-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is what was done prior to the big refactor in kernel 3.8, and what
was done by xf86-video-nv. Experimentally, it seems like there's some
sort of issue with the high-res lut to be used there. Tested on G92.
This ends up mattering because fbcon/fbdev chooses the C8 fb format for
low-vram systems, which can occur with some IGP-based configurations
with little "stolen" vram.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80675
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It's entirely possibly that the other r375 code is relevant to r370 too,
but I've not confirmed this, so I'll leave it where it is for now.
NVIDIA's copyright headers maintained, as it's still all their code.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Gourav Samaiya <gsamaiya@nvidia.com>
gcc-8 reports
drivers/gpu/drm/nouveau/nvkm/engine/pm/base.c: In function 'nvkm_perfmon_mthd':
include/linux/string.h:265:9: error: '__builtin_strncpy' specified bound 64 equals destination size [-Werror=stringop-truncation]
We need one less byte or call strlcpy() to make it a
nul-terminated string.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The kbuild test bot complained about a new coccinelle warning nearby,
which sparked a discussion about the assignment to 'memory' inside of
the conditional expression. See Link below for the original post.
Fix the assignment to silence the coccinelle warning and also make the
code look a little nicer.
Link: https://lists.freedesktop.org/archives/nouveau/2017-November/029242.html
Signed-off-by: Christoph Böhmwalder <christoph@boehmwalder.at>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Fixes failure to compile with recent envyas as a result of the 'movw'
alias being removed for v5.
A bit of history:
v3 only has a 16-bit sign-extended immediate mov op. In order to set
the high bits, there's a separate 'sethi' op. envyas validates that
the value passed to mov(imm) is between -0x8000 and 0x7fff. In order
to simplify macros that load both the low and high word, a 'movw'
alias was added which takes an unsigned 16-bit immediate. However the
actual hardware op still sign extends.
v5 has a full 32-bit immediate mov op. The v3 16-bit immediate mov op
is gone (loads 0 into the dst reg). However due to a bug in envyas,
the movw alias still existed, and selected the no-longer-present v3
16-bit immediate mov op. As a result usage of movw on v5 is the same
as mov with a 0x0 argument.
The proper fix throughout is to only ever use the 'movw' alias in
combination with 'sethi'. Anything else should get the sign-extended
validation to ensure that the intended value ends up in the
destination register.
Changes in fuc3 binaries is the result of a different encoding being
selected for a mov with an 8-bit value.
v2: added commit message written by Ilia, thanks for that!
v3: messed up rebasing, now it should apply
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
-----BEGIN PGP SIGNATURE-----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=pLN1
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.16' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This seems to have been a comparatively quieter merge window, I assume
due to holidays etc. The "biggest" change is AMD header cleanups, which
merge/remove a bunch of them. The AMD gpu scheduler is now being made generic
with the etnaviv driver wanting to reuse the code, hopefully other drivers
can go in the same direction.
Otherwise it's the usual lots of stuff in i915/amdgpu, not so much stuff
elsewhere.
Core:
- Add .last_close and .output_poll_changed helpers to reduce driver footprints
- Fix plane clipping
- Improved debug printing support
- Add panel orientation property
- Update edid derived properties at edid setting
- Reduction in fbdev driver footprint
- Move amdgpu scheduler into core for other drivers to use.
i915:
- Selftest and IGT improvements
- Fast boot prep work on IPS, pipe config
- HW workarounds for Cannonlake, Geminilake
- Cannonlake clock and HDMI2.0 fixes
- GPU cache invalidation and context switch improvements
- Display planes cleanup
- New PMU interface for perf queries
- New firmware support for KBL/SKL
- Geminilake HW workaround for perforamce
- Coffeelake stolen memory improvements
- GPU reset robustness work
- Cannonlake horizontal plane flipping
- GVT work
amdgpu/radeon:
- RV and Vega header file cleanups (lots of lines gone!)
- TTM operation context support
- 48-bit GPUVM support for Vega/RV
- ECC support for Vega
- Resizeable BAR support
- Multi-display sync support
- Enable swapout for reserved BOs during allocation
- S3 fixes on Raven
- GPU reset cleanup and fixes
- 2+1 level GPU page table
amdkfd:
- GFX7/8 SDMA user queues support
- Hardware scheduling for multiple processes
- dGPU prep work
rcar:
- Added R8A7743/5 support
- System suspend/resume support
sun4i:
- Multi-plane support for YUV formats
- A83T and LVDS support
msm:
- Devfreq support for GPU
tegra:
- Prep work for adding Tegra186 support
- Tegra186 HDMI support
- HDMI2.0 and zpos support by using generic helpers
tilcdc:
- Misc fixes
omapdrm:
- Support memory bandwidth limits
- DSI command mode panel cleanups
- DMM error handling
exynos:
- drop the old IPP subdriver.
etnaviv:
- Occlusion query fixes
- Job handling fixes
- Prep work for hooking in gpu scheduler
armada:
- Move closer to atomic modesetting
- Allow disabling primary plane if overlay is full screen
imx:
- Format modifier support
- Add tile prefetch to PRE
- Runtime PM support for PRG
ast:
- fix LUT loading"
* tag 'drm-for-v4.16' of git://people.freedesktop.org/~airlied/linux: (1471 commits)
drm/ast: Load lut in crtc_commit
drm: Check for lessee in DROP_MASTER ioctl
drm: fix gpu scheduler link order
drm/amd/display: Demote error print to debug print when ATOM impl missing
dma-buf: fix reservation_object_wait_timeout_rcu once more v2
drm/amdgpu: Avoid leaking PM domain on driver unbind (v2)
drm/amd/amdgpu: Add Polaris version check
drm/amdgpu: Reenable manual GPU reset from sysfs
drm/amdgpu: disable MMHUB power gating on raven
drm/ttm: Don't unreserve swapped BOs that were previously reserved
drm/ttm: Don't add swapped BOs to swap-LRU list
drm/amdgpu: only check for ECC on Vega10
drm/amd/powerplay: Fix smu_table_entry.handle type
drm/ttm: add VADDR_FLAG_UPDATED_COUNT to correctly update dma_page global count
drm: Fix PANEL_ORIENTATION_QUIRKS breaking the Kconfig DRM menuconfig
drm/radeon: fill in rb backend map on evergreen/ni.
drm/amdgpu/gfx9: fix ngg enablement to clear gds reserved memory (v2)
drm/ttm: only free pages rather than update global memory count together
drm/amdgpu: fix CPU based VM updates
drm/amdgpu: fix typo in amdgpu_vce_validate_bo
...
to the clk rate protection support added by Jerome Brunet. This feature
will allow consumers to lock in a certain rate on the output of a clk so
that things like audio playback don't hear pops when the clk frequency
changes due to shared parent clks changing rates. Currently the clk
API doesn't guarantee the rate of a clk stays at the rate you request
after clk_set_rate() is called, so this new API will allow drivers
to express that requirement. Beyond this, the core got some debugfs
pretty printing patches and a couple minor non-critical fixes.
Looking outside of the core framework diff we have some new driver
additions and the removal of a legacy TI clk driver. Both of these hit
high in the dirstat. Also, the removal of the asm-generic/clkdev.h file
causes small one-liners in all the architecture Kbuild files. Overall, the
driver diff seems to be the normal stuff that comes all the time to
fix little problems here and there and to support new hardware.
Core:
- Clk rate protection
- Symbolic clk flags in debugfs output
- Clk registration enabled clks while doing bookkeeping updates
New Drivers:
- Spreadtrum SC9860
- HiSilicon hi3660 stub
- Qualcomm A53 PLL, SPMI clkdiv, and MSM8916 APCS
- Amlogic Meson-AXG
- ASPEED BMC
Removed Drivers:
- TI OMAP 3xxx legacy clk (non-DT) support
- asm*/clkdev.h got removed (not really a driver)
Updates:
- Renesas FDP1-0 module clock on R-Car M3-W
- Renesas LVDS module clock on R-Car V3M
- Misc fixes to pr_err() prints
- Qualcomm MSM8916 audio fixes
- Qualcomm IPQ8074 rounded out support for more peripherals
- Qualcomm Alpha PLL variants
- Divider code was using container_of() on bad pointers
- Allwinner DE2 clks on H3
- Amlogic minor data fixes and dropping of CLK_IGNORE_UNUSED
- Mediatek clk driver compile test support
- AT91 PMC clk suspend/resume restoration support
- PLL issues fixed on si5351
- Broadcom IProc PLL calculation updates
- DVFS support for Armada mvebu CPU clks
- Allwinner fixed post-divider support
- TI clkctrl fixes and support for newer SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=bGPp
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework has a handful of patches this time around, mostly
due to the clk rate protection support added by Jerome Brunet.
This feature will allow consumers to lock in a certain rate on the
output of a clk so that things like audio playback don't hear pops
when the clk frequency changes due to shared parent clks changing
rates. Currently the clk API doesn't guarantee the rate of a clk stays
at the rate you request after clk_set_rate() is called, so this new
API will allow drivers to express that requirement.
Beyond this, the core got some debugfs pretty printing patches and a
couple minor non-critical fixes.
Looking outside of the core framework diff we have some new driver
additions and the removal of a legacy TI clk driver. Both of these hit
high in the dirstat. Also, the removal of the asm-generic/clkdev.h
file causes small one-liners in all the architecture Kbuild files.
Overall, the driver diff seems to be the normal stuff that comes all
the time to fix little problems here and there and to support new
hardware.
Summary:
Core:
- Clk rate protection
- Symbolic clk flags in debugfs output
- Clk registration enabled clks while doing bookkeeping updates
New Drivers:
- Spreadtrum SC9860
- HiSilicon hi3660 stub
- Qualcomm A53 PLL, SPMI clkdiv, and MSM8916 APCS
- Amlogic Meson-AXG
- ASPEED BMC
Removed Drivers:
- TI OMAP 3xxx legacy clk (non-DT) support
- asm*/clkdev.h got removed (not really a driver)
Updates:
- Renesas FDP1-0 module clock on R-Car M3-W
- Renesas LVDS module clock on R-Car V3M
- Misc fixes to pr_err() prints
- Qualcomm MSM8916 audio fixes
- Qualcomm IPQ8074 rounded out support for more peripherals
- Qualcomm Alpha PLL variants
- Divider code was using container_of() on bad pointers
- Allwinner DE2 clks on H3
- Amlogic minor data fixes and dropping of CLK_IGNORE_UNUSED
- Mediatek clk driver compile test support
- AT91 PMC clk suspend/resume restoration support
- PLL issues fixed on si5351
- Broadcom IProc PLL calculation updates
- DVFS support for Armada mvebu CPU clks
- Allwinner fixed post-divider support
- TI clkctrl fixes and support for newer SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (125 commits)
clk: aspeed: Handle inverse polarity of USB port 1 clock gate
clk: aspeed: Fix return value check in aspeed_cc_init()
clk: aspeed: Add reset controller
clk: aspeed: Register gated clocks
clk: aspeed: Add platform driver and register PLLs
clk: aspeed: Register core clocks
clk: Add clock driver for ASPEED BMC SoCs
clk: mediatek: adjust dependency of reset.c to avoid unexpectedly being built
clk: fix reentrancy of clk_enable() on UP systems
clk: meson-axg: fix potential NULL dereference in axg_clkc_probe()
clk: Simplify debugfs registration
clk: Fix debugfs_create_*() usage
clk: Show symbolic clock flags in debugfs
clk: renesas: r8a7796: Add FDP clock
clk: Move __clk_{get,put}() into private clk.h API
clk: sunxi: Use CLK_IS_CRITICAL flag for critical clks
clk: Improve flags doc for of_clk_detect_critical()
arch: Remove clkdev.h asm-generic from Kbuild
clk: sunxi-ng: a83t: Add M divider to TCON1 clock
clk: Prepare to remove asm-generic/clkdev.h
...
- Mask INTx from user if pdev->irq is zero (Alexey Kardashevskiy)
- Capability helper cleanup (Alex Williamson)
- Allow mmaps overlapping MSI-X vector table with region capability
exposing this feature (Alexey Kardashevskiy)
- mdev static cleanups (Xiongwei Song)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=Ww3n
-----END PGP SIGNATURE-----
Merge tag 'vfio-v4.16-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- Mask INTx from user if pdev->irq is zero (Alexey Kardashevskiy)
- Capability helper cleanup (Alex Williamson)
- Allow mmaps overlapping MSI-X vector table with region capability
exposing this feature (Alexey Kardashevskiy)
- mdev static cleanups (Xiongwei Song)
* tag 'vfio-v4.16-rc1' of git://github.com/awilliam/linux-vfio:
vfio: mdev: make a couple of functions and structure vfio_mdev_driver static
vfio-pci: Allow mapping MSIX BAR
vfio: Simplify capability helper
vfio-pci: Mask INTx if a device is not capabable of enabling it
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
Previously, we relied on only running the hangcheck while somebody was
waiting on the GPU, in order to minimise the amount of time hangcheck
had to run. (If nobody was watching the GPU, nobody would notice if the
GPU wasn't responding -- eventually somebody would care and so kick
hangcheck into action.) However, this falls apart from around commit
4680816be3 ("drm/i915: Wait first for submission, before waiting for
request completion"), as not all waiters declare themselves to hangcheck
and so we could switch off hangcheck and miss GPU hangs even when
waiting under the struct_mutex.
If we enable hangcheck from the first request submission, and let it run
until the GPU is idle again, we forgo all the complexity involved with
only enabling around waiters. We just have to remember to be careful that
we do not declare a GPU hang when idly waiting for the next request to
be come ready, as we will run hangcheck continuously even when the
engines are stalled waiting for external events. This should be true
already as we should only be tracking requests submitted to hardware for
execution as an indicator that the engine is busy.
Fixes: 4680816be3 ("drm/i915: Wait first for submission, before waiting for request completion"
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104840
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129144104.3921-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
(cherry picked from commit 889230489b)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In case of eDP because the panel has a fixed mode, the link rate
and lane count at which it is trained corresponds to the link BW
required to support the native resolution of the panel. In case of
panles with lower resolutions where fewer lanes are hooked up internally,
that number is reflected in the MAX_LANE_COUNT DPCD register of the panel.
So it is pointless to fallback to lower link rate/lane count in case
of link training failure on eDP connector since the lower link BW
will not support the native resolution of the panel and we cannot
prune the preferred mode on the eDP connector.
In case of Link training failure on the eDP panel, something is wrong
in the HW internally and hence driver errors out with a loud
and clear DRM_ERROR message.
v2:
* Fix the DEBUG_ERROR and add {} in else (Ville Syrjala)
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=103369
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507835618-23051-1-git-send-email-manasi.d.navare@intel.com
(cherry picked from commit c0cfb10d9e)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We may have fused or unused pipes in our system. Let's check that the pipe
in question is within limits of accessible pipes. In case, that we are not
able to access the pipe, we return early with a warning.
v2: Rephrasing of the commit message (Jani)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103206
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jaswinder Singh Rajput <jaswinder@perfectintelligent.com>
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1513584243-12607-1-git-send-email-mika.kahola@intel.com
(cherry picked from commit 0b7029b7e4)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: <stable@vger.kernel.org> # v4.10+
As we attempt to allocate pages for use in a new WC stash, direct
reclaim may run underneath us and fill up the WC stash. We have to be
careful then not to overflow the pvec.
Fixes: 66df1014ef ("drm/i915: Keep a small stash of preallocated WC pages")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103109
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180121173143.17090-1-chris@chris-wilson.co.uk
(cherry picked from commit 073cd78166)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Since commit 4e773c3a8a ("drm/i915: Wire up shrinkctl->nr_scanned"),
we track the number of objects we scan and do not wish to exceed that as
it will overly penalise our own slabs under mempressure. Given that we
now know the target number of objects to scan, use that as our guide for
deciding to shrink as opposed to the number of objects we manage to
shrink (which doesn't correspond to the numbers we report to shrinkctl).
Fixes: 4e773c3a8a ("drm/i915: Wire up shrinkctl->nr_scanned")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180115212455.24046-2-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
(cherry picked from commit 29d384e34c)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Stop gvt scheduler timer if no vGPU exists, otherwise it keeps
gvt service thread busy to handle request schedule event but no
actual schedule activity required.
Reviewed-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Stop irq timer for virtual vblank timer emulation if no vGPU exists,
otherwise it will keep gvt service thread busy to handle virtual vblank
but no use.
Reviewed-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
According to commit (319c933c71)
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Aug 15 00:02:46 2013 +0200
drm/prime: proper locking+refcounting for obj->dma_buf link
obj->dma_buf link should be reinstated at import time.
Gvt-g dma-buf buffer exposeing might be simpler, as there won't be much
racing during Gvt-g dma-buf exposing. In other words, Gvt-g dma-buf
exposing can guarantee exposing happens before gem close ioctl, and Gvt-g
is the only exporter of the guest framebuffer.
But following the drm prime scheme can give Gvt-g a chance to increase a
dma-buf reference count during importing. Otherwise, we have to increase
the reference during exposing, which will break the case that the only
reference userspace has held was through the dma-buf fd and the reference
count is one.
Signed-off-by: Tina Zhang <tina.zhang@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Cc: Hang Yuan <hang.yuan@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We have a hole in our busy-stat accounting if the pmu is enabled during
a long running batch, the pmu will not start accumulating busy-time
until the next context switch. This then fails tests that are only
sampling a single batch.
v2: Count each active port just once (context in/out events are only on
the first and last assignment to a port).
v3: Avoid hardcoding knowledge of 2 submission ports
Fixes: 30e17b7847 ("drm/i915: Engine busy time tracking")
Testcase: igt/perf_pmu/busy-start
Testcase: igt/perf_pmu/busy-double-start
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111073031.14614-1-chris@chris-wilson.co.uk
(cherry picked from commit 4900727d35)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This register does not contain it. Instead, we have to look into FAULT_TLB_DATA0 & 1
(where, by the way, we can also get the address space).
v2: Right formatting
v3:
- Use 12 (as per the register format) instead of PAGE_SIZE (Chris)
- s/BITS_44_TO_47/HIGHBITS (Chris)
- Right formatting, this time for real
Fixes: b03ec3d67a ("drm/i915: There is only one fault register from GEN8 onwards")
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1513982329-32191-1-git-send-email-oscar.mateo@intel.com
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 5a3f58dfd1)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
While moving code around for solving lockdep issue for GuC log relay,
spotted that uc_fini_wq is not being called in failure path in gem_init.
Missed in the below commit. Add it.
v2: Removed GEM_BUG_ON(!HAS_GUC()) from intel_uc_fini_wq as init happens
only based on enable_guc module parameter and does not consider has_guc
capability. (Michal)
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Fixes: 3176ff49bc ("drm/i915/guc: Move GuC workqueue allocations outside of the mutex")
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1515588857-10283-1-git-send-email-sagar.a.kamble@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit da943b5ab0)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The power domain masks are 64 bit wide, so we need BIT_ULL() when
setting bits in them, these ones were missed during converting from 32
to 64 bit masks. All 3 enums are <32 atm, so this didn't cause a real
problem.
Fixes: d8fc70b736 ("drm/i915: Make power domain masks 64 bit long")
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109122040.19425-1-imre.deak@intel.com
(cherry picked from commit 17bd6e66d8)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The ACK/NACK implementation as found in e.g. the G965 has the falling
clock edge and the release of the data line after the ACK for the received
byte happen at the same time.
This is conformant with the I2C specification, which allows a zero hold
time, see footnote [3]: "A device must internally provide a hold time of
at least 300 ns for the SDA signal (with respect to the V IH(min) of the
SCL signal) to bridge the undefined region of the falling edge of SCL."
Some HDMI-to-VGA converters apparently fail to adhere to this requirement
and latch SDA at the falling clock edge, so instead of an ACK
sometimes a NACK is read and the slave (i.e. the EDID ROM) ends the
transfer.
The bitbanging releases the data line for the ACK only 1/4 bit time after
the falling clock edge, so a slave will see the correct value no matter
if it samples at the rising or the falling clock edge or in the center.
Fallback to bitbanging is already done for the CRT connector.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92685
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/a39f080b-81a5-4c93-b3f7-7cb0a58daca3@rwthex-w2-a.rwth-ad.de
(cherry picked from commit cfb926e148)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The mocs reg array is defined locally but then we iterate over its
elements using I915_NUM_ENGINES. There is no 'hard' connection between
I915_NUM_ENGINES and the regs array and there will be problems if either
of them increases.
Use the size of the mocs reg array instead to safely iterate over it.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Weinan Li <weinan.z.li@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
GVT may receive partial write on one guest PTE update. Validate gfn
not to translate incomplete gfn. This avoids some unnecessary error
messages incurred by the incomplete gfn translating. Also fix the
bug that the whole PPGTT shadow page update is aborted on any invalid
gfn entry.
gfn validation relys on hypervisor's help. Add one MPT module function
to provide the function.
Signed-off-by: Hang Yuan <hang.yuan@intel.com>
Reviewed-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Running 4.15 Linux kernel in VM will cause host GVT reports
'untrack mmio 0x701a0' errror, which identifies the PLANE_KEYMAX
registers. Add them to track list.
v2: rebase to latest staging code.
Signed-off-by: Pei Zhang <pei.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
while(mmio++) increase mmio to next, mmio[0] never take effect
in while loop.
This patch change while to for and fix the above issue.
v2: Correct Fixes format.(Zhenyu)
v3: Rebase to latest staging.(Zhenyu)
Fixes: 83164886e455("drm/i915/gvt: Select appropriate mmio list at initialization time")
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
During a non-blocking commit, it is possible to return before the
commit_tail work is queued (-ERESTARTSYS, for example).
Since a reference on the crtc commit object is obtained for the pending
vblank event when preparing the commit, the above situation will leave
us with an extra reference.
Therefore, if the commit_tail worker has not consumed the event at the
end of a commit, release it's reference.
Changes since v1:
- Also check for state->event->base.completion being set, to
handle the case where stall_checks() fails in setup_crtc_commit().
Changes since v2:
- Add a flag to drm_crtc_commit, to prevent dereferencing a freed event.
i915 may unreference the state in a worker.
Fixes: 24835e442f ("drm: reference count event->completion")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com> #v1
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117115108.29608-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Sean Paul <seanpaul@chromium.org>
In the past the ast driver relied upon the fbdev emulation helpers to
call ->load_lut at boot-up. But since
commit b8e2b0199c
Author: Peter Rosin <peda@axentia.se>
Date: Tue Jul 4 12:36:57 2017 +0200
drm/fb-helper: factor out pseudo-palette
that's cleaned up and drivers are expected to boot into a consistent
lut state. This patch fixes that.
Fixes: b8e2b0199c ("drm/fb-helper: factor out pseudo-palette")
Cc: Peter Rosin <peda@axenita.se>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.14+
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=198123
Cc: Bill Fraser <bill.fraser@gmail.com>
Reported-and-Tested-by: Bill Fraser <bill.fraser@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
another one when waiting for timeouts on reservation objects.
-----BEGIN PGP SIGNATURE-----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=h8qb
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-fixes-2018-01-31' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
This contains a fix to restrict what lessee can do with masters and
another one when waiting for timeouts on reservation objects.
* tag 'drm-misc-next-fixes-2018-01-31' of git://anongit.freedesktop.org/drm/drm-misc:
drm: Check for lessee in DROP_MASTER ioctl
dma-buf: fix reservation_object_wait_timeout_rcu once more v2
Pull misc vfs updates from Al Viro:
"All kinds of misc stuff, without any unifying topic, from various
people.
Neil's d_anon patch, several bugfixes, introduction of kvmalloc
analogue of kmemdup_user(), extending bitfield.h to deal with
fixed-endians, assorted cleanups all over the place..."
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (28 commits)
alpha: osf_sys.c: use timespec64 where appropriate
alpha: osf_sys.c: fix put_tv32 regression
jffs2: Fix use-after-free bug in jffs2_iget()'s error handling path
dcache: delete unused d_hash_mask
dcache: subtract d_hash_shift from 32 in advance
fs/buffer.c: fold init_buffer() into init_page_buffers()
fs: fold __inode_permission() into inode_permission()
fs: add RWF_APPEND
sctp: use vmemdup_user() rather than badly open-coding memdup_user()
snd_ctl_elem_init_enum_names(): switch to vmemdup_user()
replace_user_tlv(): switch to vmemdup_user()
new primitive: vmemdup_user()
memdup_user(): switch to GFP_USER
eventfd: fold eventfd_ctx_get() into eventfd_ctx_fileget()
eventfd: fold eventfd_ctx_read() into eventfd_read()
eventfd: convert to use anon_inode_getfd()
nfs4file: get rid of pointless include of btrfs.h
uvc_v4l2: clean copyin/copyout up
vme_user: don't use __copy_..._user()
usx2y: don't bother with memdup_user() for 16-byte structure
...
In the past the ast driver relied upon the fbdev emulation helpers to
call ->load_lut at boot-up. But since
commit b8e2b0199c
Author: Peter Rosin <peda@axentia.se>
Date: Tue Jul 4 12:36:57 2017 +0200
drm/fb-helper: factor out pseudo-palette
that's cleaned up and drivers are expected to boot into a consistent
lut state. This patch fixes that.
Fixes: b8e2b0199c ("drm/fb-helper: factor out pseudo-palette")
Cc: Peter Rosin <peda@axenita.se>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.14+
References: https://bugzilla.kernel.org/show_bug.cgi?id=198123
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20180131110450.22153-1-daniel.vetter@ffwll.ch
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Don't let a lessee control what the current DRM master is set to;
that's the job of the "real" master. Otherwise, the lessee would
disable all access to master operations for the owner and all lessees
under it.
This matches the same check made in the SET_MASTER ioctl.
Signed-off-by: Keith Packard <keithp@keithp.com>
Fixes: 2ed077e467 ("drm: Add drm_object lease infrastructure [v5]")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119015159.1606-1-keithp@keithp.com
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
The CGCG feature on Stoney is causing GFX related
issues such as freezes and blank outs.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check the variable that was most recently initialized.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x, y, f, g, e, m;
statement S1,S2,S3,S4;
@@
x = f(...);
if (\(<+...x...+>\&e\)) S1 else S2
(
x = g(...);
|
m = g(...,&x,...);
|
y = g(...);
*if (e)
S3 else S4
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
It can easily be that the VM is already destroyed when this runs.
v2: fix test inversion
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The vm pointer can become invalid as soon as the lock is released.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The root PD can be evicted directly after allocating it, just validate
it on first use.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It must use queue id 0, because CGPG_IDLE/SAVE/LOAD/RUN only can be issued on
queue 0.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The buf pointer was not being incremented inside the loop
meaning the same block of data would be read or written
repeatedly.
(v2) Change 'buf' pointer to uint8_t* type
Cc: stable@vger.kernel.org
Fixes: 09ac4fcb3f ("drm/ttm: Implement vm_operations_struct.access v2")
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Missed in the patche:
dc94777 drm/ttm: enable swapout for reserved BOs during allocation.
don't unreserve the BO if it is not reserved by itself.
Signed-off-by: Roger He <Hongbo.He@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For a while we've been having issues with seemingly random interrupts
coming from nvidia cards when resuming them. Originally the fix for this
was thought to be just re-arming the MSI interrupt registers right after
re-allocating our IRQs, however it seems a lot of what we do is both
wrong and not even nessecary.
This was made apparent by what appeared to be a regression in the
mainline kernel that started introducing suspend/resume issues for
nouveau:
a0c9259dc4 (irq/matrix: Spread interrupts on allocation)
After this commit was introduced, we started getting interrupts from the
GPU before we actually re-allocated our own IRQ (see references below)
and assigned the IRQ handler. Investigating this turned out that the
problem was not with the commit, but the fact that nouveau even
free/allocates it's irqs before and after suspend/resume.
For starters: drivers in the linux kernel haven't had to handle
freeing/re-allocating their IRQs during suspend/resume cycles for quite
a while now. Nouveau seems to be one of the few drivers left that still
does this, despite the fact there's no reason we actually need to since
disabling interrupts from the device side should be enough, as the
kernel is already smart enough to know to disable host-side interrupts
for us before going into suspend. Since we were tearing down our IRQs by
hand however, that means there was a short period during resume where
interrupts could be received before we re-allocated our IRQ which would
lead to us getting an unhandled IRQ. Since we never handle said IRQ and
re-arm the interrupt registers, this would cause us to miss all of the
interrupts from the GPU and cause our init process to start timing out
on anything requiring interrupts.
So, since this whole setup/teardown every suspend/resume cycle is
useless anyway, move irq setup/teardown into the pci subdev's ctor/dtor
functions instead so they're only called at driver load and driver
unload. This should fix most of the issues with pending interrupts on
resume, along with getting suspend/resume for nouveau to work again.
As well, this probably means we can also just remove the msi rearm call
inside nvkm_pci_init(). But since our main focus here is to fix
suspend/resume before 4.15, we'll save that for a later patch.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
One fixes a NULL dereference, and the other fixes
a flickering bug.
Cc: Eric Anholt <eric@anholt.net>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlpo1gAACgkQlvcN/ahK
Bwp8Dwf/cOHYKoyKmzzMNy4Myrsf0I8cF4efL9f1xw7Y/m/pp7c6Nxdfj0TCmVpd
AmLuxg8rSYrfdnzY5KZ/9nr8RYiWmnX5VIt8VapbZyWF20UUyqilPepHsBrI8lig
rczaOJ8kWL7FDHqXM0CXHQc6mhd7lqKXNfaAwUE3cE9yAve/4tTytrRBXzuhmMmH
AQYsf0Y7v4rv+4SJEZM4UA2n8+TV4WaY1nqjED37lIdApqntL9hR8056lpevWT3W
GgrakE8mZVFTu5KGIBCvZy3yehO/KJ0RIKvPwXJC9e8SMEcP35NuLw0+CetcNTrL
MYure0STUMH0VR9wGLKOh2+bn1106g==
=NPug
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2018-01-24' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Two vc4 fixes that were applied in the last day.
One fixes a NULL dereference, and the other fixes
a flickering bug.
Cc: Eric Anholt <eric@anholt.net>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
* tag 'drm-misc-fixes-2018-01-24' of git://anongit.freedesktop.org/drm/drm-misc:
drm/vc4: Fix NULL pointer dereference in vc4_save_hang_state()
drm/vc4: Flush the caches before the bin jobs, as well.
Fixes one Kconfig issue and a enable some panels to work properly.
There is also a fix of error code return in sun4i.
-----BEGIN PGP SIGNATURE-----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=NLL4
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-fixes-2018-01-18' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
Fixes for 4.16:
Fixes one Kconfig issue and a enable some panels to work properly.
There is also a fix of error code return in sun4i.
* tag 'drm-misc-next-fixes-2018-01-18' of git://anongit.freedesktop.org/drm/drm-misc:
drm: Fix PANEL_ORIENTATION_QUIRKS breaking the Kconfig DRM menuconfig
drm/panel: lvds: Handle the optional regulator case properly
drm/sun4i: Fix error code in sun4i_tcon_bind()
A few more fixes for 4.16, nothing major.
A few more fixes for 4.16. This is on top of the pull request from
last week. Most notable change here is a fix to the link order for
the now separate from amdgpu GPU scheduler to fix crashes when the
modules are build into the kernel rather than as modules.
* 'drm-next-4.16' of git://people.freedesktop.org/~agd5f/linux:
drm: fix gpu scheduler link order
drm/amd/display: Demote error print to debug print when ATOM impl missing
drm/amdgpu: Avoid leaking PM domain on driver unbind (v2)
drm/amd/amdgpu: Add Polaris version check
drm/amdgpu: Reenable manual GPU reset from sysfs
drm/amdgpu: disable MMHUB power gating on raven
drm/ttm: Don't unreserve swapped BOs that were previously reserved
drm/ttm: Don't add swapped BOs to swap-LRU list
drm/amdgpu: only check for ECC on Vega10
drm/amd/powerplay: Fix smu_table_entry.handle type
drm/ttm: add VADDR_FLAG_UPDATED_COUNT to correctly update dma_page global count
drm/radeon: fill in rb backend map on evergreen/ni.
drm/amdgpu/gfx9: fix ngg enablement to clear gds reserved memory (v2)
drm/ttm: only free pages rather than update global memory count together
drm/amdgpu: fix CPU based VM updates
drm/amdgpu: fix typo in amdgpu_vce_validate_bo
drm/amdgpu: fix amdgpu_vm_pasid_fault_credit
drm/ttm: check the return value of register_shrinker
drm/radeon: fix sparse warning: Should it be static?
It should initialize before the drivers using it.
Signed-off-by: Christian König <christian.koenig@amd.com>
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=104736
Reviewed-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I assumed wrongfully that all relevant functions should be implemented.
Apparently this isn't the case. Demote the print to debug level for now.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We only support vga_switcheroo and runtime pm on PX/HG systems
so forcing runpm to 1 doesn't do anything useful anyway.
Only call vga_switcheroo_init_domain_pm_ops() for PX/HG so
that the cleanup path is correct as well. This mirrors what
radeon does as well.
v2: rework the patch originally sent by Lukas (Alex)
Acked-by: Lukas Wunner <lukas@wunner.de>
Reported-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de> (v1)
Cc: stable@vger.kernel.org
Add Polaris version check if firmware support UVD encode
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Otherwise it keeps rejecting the reset.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
MMHUB power gating still has issue, and doesn't work on raven at current. So
disable it for the moment.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
follow-up fix
-----BEGIN PGP SIGNATURE-----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=PwII
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-fixes-2018-01-18' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Display corruption regression bugfix with both a prep patch and a
follow-up fix
* tag 'drm-intel-fixes-2018-01-18' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Fix deadlock in i830_disable_pipe()
drm/i915: Redo plane sanitation during readout
drm/i915: Add .get_hw_state() method for planes
Thought I'd try my luck getting one more in:
- Two fixes for Tegra (one is to common code, but our userspace doesn't hit it).
- One for NV5x-class MCPs
* 'linux-4.15' of git://github.com/skeggsb/linux:
drm/nouveau/mmu/mcp77: fix regressions in stolen memory handling
drm/nouveau/bar/gk20a: Avoid bar teardown during init
drm/nouveau/drm/nouveau: Pass the proper arguments to nvif_object_map_handle()
- Fixes addition of stolen memory base address to PTEs.
- Removes support for compression.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Tested-by: Pierre Moreau <pierre.morrow@free.fr>
Commit bbb163e189 ("drm/nouveau/bar: implement bar1 teardown")
introduced add a teardown helper function for BAR1. During
initialisation of the Nouveau, initially all the teardown helpers are
called once, before calling their init counterparts. For gk20a, after
the BAR1 teardown function is called, the device is hanging during the
initialisation of the FB sub-device. At this point it is unclear why
this is happening and this is still under investigation. However, this
change is preventing Tegra124 devices from booting when Nouveau is
enabled. To allow Tegra124 to boot, remove the teardown helper for
gk20a.
This is based upon a previous patch by Guillaume Tucker but limits
the workaround to only gk20a GPUs.
Fixes: bbb163e189 ("drm/nouveau/bar: implement bar1 teardown")
Reported-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is obviously wrong in the current code. Make sure to record the
correct size of the arguments and pass the actual arguments to the
nvif_object_map_handle() function.
Suggested-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
If ttm_bo_swapout doesn't own the lock, don't release it. Someone
else probably depends on it still being locked.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A BO that's already swapped would be added back to the swap-LRU list
for example if its validation failed under high memory pressure. This
could later lead to swapping it out again and leaking previous swap
storage.
This commit adds a condition to prevent that from happening.
v2: Check page_flags instead of swap_storage
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
RV doesn't support it.
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The handle describes kernel logical address, should be
unsigned long and not uint32_t.
Fixes KASAN error and GFP on driver unload.
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
add this for correctly updating global mem count in ttm_mem_zone.
before that when ttm_mem_global_alloc_page fails, we would update all
dma_page's global mem count in ttm_dma->pages_list. but actually here
we should not update for the last dma_page.
v2: only the update of last dma_page is not right
v3: use lower bits of dma_page vaddr
Signed-off-by: Roger He <Hongbo.He@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When saving BOs in the hang state we skip one entry of the
kernel_state->bo[] array, thus leaving it to NULL. This leads to a NULL
pointer dereference when, later in this function, we iterate over all
BOs to check their ->madv state.
Fixes: ca26d28bba ("drm/vc4: improve throughput by pipelining binning and rendering jobs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180118145821.22344-1-boris.brezillon@free-electrons.com
If the frame samples from a render target that was just written, its
cache flush during the binning step may have occurred before the
previous frame's RCL was completed. Flush the texture caches again
before starting each RCL job to make sure that the sampling of the
previous RCL's output is correct.
Fixes flickering in the top left of 3DMMES Taiji.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: ca26d28bba ("drm/vc4: improve throughput by pipelining binning and rendering jobs")
Link: https://patchwork.freedesktop.org/patch/msgid/20171221221722.23809-1-eric@anholt.net
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Final 4.15 drm-misc pull:
Just 3 sun4i patches to fix clock computation/checks.
* tag 'drm-misc-fixes-2018-01-17' of git://anongit.freedesktop.org/drm/drm-misc:
drm/sun4i: hdmi: Add missing rate halving check in sun4i_tmds_determine_rate
drm/sun4i: hdmi: Fix incorrect assignment in sun4i_tmds_determine_rate
drm/sun4i: hdmi: Check for unset best_parent in sun4i_tmds_determine_rate
Last minute fixes for vmwgfx.
One fix for a drm helper warning introduced in 4.15
One important fix for a longer standing memory corruption issue on older
hardware versions.
* 'vmwgfx-fixes-4.15' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: fix memory corruption with legacy/sou connectors
drm/vmwgfx: Fix a boot time warning
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaW+iVAAoJEHm+PkMAQRiGCDsIAJALNpX7odTx/8y+yCSWbpBH
E57iwr4rmnI6tXJY6gqBUWTYnjAcf4b8IsHGCO6q3WIE3l/kt+m3eA21a32mF2Db
/bfPGTOWu5LoOnFqzgH2kiFuC3Y474toxpld2YtkQWYxi5W7SUtIHi/jGgkUprth
g15yPfwYgotJd/gpmPfBDMPlYDYvLlnPYbTG6ZWdMbg39m2RF2m0BdQ6aBFLHvbJ
IN0tjCM6hrLFBP0+6Zn60pevUW9/AFYotZn2ankNTk5QVCQm14rgQIP+Pfoa5WpE
I25r0DbkG2jKJCq+tlgIJjxHKD37GEDMc4T8/5Y8CNNeT9Q8si9EWvznjaAPazw=
=o5gx
-----END PGP SIGNATURE-----
BackMerge tag 'v4.15-rc8' into drm-next
Linux 4.15-rc8
Daniel requested this for so the intel CI won't fall over on drm-next
so often.
It looks like in all cases 'struct vmw_connector_state' is used. But
only in stdu connectors, was atomic_{duplicate,destroy}_state() properly
subclassed. Leading to writes beyond the end of the allocated connector
state block and all sorts of fun memory corruption related crashes.
Fixes: d7721ca711 "drm/vmwgfx: Connector atomic state"
Cc: <stable@vger.kernel.org>
Signed-off-by: Rob Clark <rclark@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
All Kconfig menu menu entries should have a depends on MENU_OPTION, the
menu stops after the first Kconfig entry without this depends on.
Since the PANEL_ORIENTATION_QUIRKS option is also used outside of DRM,
it deliberately does not have a depends on DRM, but this causes all
items after it to show as separate items rather then under the DRM
menuconfig.
This commit moves PANEL_ORIENTATION_QUIRKS to the end of the drm Kconfig
file, grouping it with DRM_LIB_RANDOM which also does not depend on DRM,
fixing the DRM menuconfig.
Fixes: 404d1a3edc ("drm: Add panel orientation quirks, v6.")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117081032.6411-1-hdegoede@redhat.com
The 4.15 vmwgfx driver shows a warning during boot.
It is caused by a mismatch between the result of vmw_enable_vblank()
and what the drm_atomic_helper expects.
Signed-off by: Woody Suwalski <terraluna977@gmail.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
This looks to have never gotten filled in, and it seems to
trigger a bug in mesa.
Reviewed-by: Roland Scheidegger <sroland@vmware.com>
Reported-by: Roland Scheidegger <sroland@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: fix register access
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Ken Wang <ken.wang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
if ttm_get_pages or ttm_mem_global_alloc_page fail, should not update
global memory count.
Signed-off-by: Roger He <Hongbo.He@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
That got accidentially removed.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As soon as the lock is dropped the VM pointer can be invalid.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes the build warning:
"ignoring return value of 'register_shrinker', declared with
attribute warn_unused_result [-Wunused-result]"
Signed-off-by: Roger He <Hongbo.He@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Impact: make symbol static.
Fix this sparse warning:
drivers/gpu/drm/radeon/radeon_dp_mst.c:332:38: warning: symbol 'mst_cbs' was not declared. Should it be static?
Signed-off-by: Dmitry Rozhkov <dmitry.rozhkov@linux.intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
i830_disable_pipe() gets called from the power well code, and thus
we're already holding the power domain mutex. That means we can't
call plane->get_hw_state() as it will also try to grab the
same mutex and will thus deadlock.
Replace the assert_plane() calls (which calls ->get_hw_state()) with
just raw register reads in i830_disable_pipe(). As a bonus we can
now get a warning if plane C is enabled even though we don't even
expose it as a drm plane.
v2: Do a separate WARN_ON() for each plane (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: d87ce76402 ("drm/i915: Add .get_hw_state() method for planes")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129125411.29055-1-ville.syrjala@linux.intel.com
(cherry picked from commit 5816d9cbc0)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Unify the plane disabling during state readout by pulling the code into
a new helper intel_plane_disable_noatomic(). We'll also read out the
state of all planes, so that we know which planes really need to be
diabled.
Additonally we change the plane<->pipe mapping sanitation to work by
simply disabling the offending planes instead of entire pipes. And
we do it before we otherwise sanitize the crtcs, which means we don't
have to worry about misassigned planes during crtc sanitation anymore.
v2: Reoder patches to not depend on enum old_plane_id
v3: s/for_each_pipe/for_each_intel_crtc/
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alex Villacís Lasso <alexvillacislasso@hotmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103223
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171117191917.11506-3-ville.syrjala@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit b1e01595a6)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add a .get_hw_state() method for planes, returning true or false
depending on whether the plane is enabled. Use it to rewrite the
plane enabled/disabled asserts in platform agnostic fashion.
We do lose the pre-gen4 plane<->pipe mapping checks, but since we're
supposed sanitize that anyway it doesn't really matter.
v2: Reoder patches to not depend on enum old_plane_id
Just call assert_plane_disabled() from assert_planes_disabled()
v3: Deal with disabled power wells in .get_hw_state()
v4: Rebase due skl primary plane code removal
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alex Villacís Lasso <alexvillacislasso@hotmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> #v2
Tested-by: Thierry Reding <thierry.reding@gmail.com> #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20171117191917.11506-2-ville.syrjala@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit 51f5a09639)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The devm_regulator_get_optional function, unlike it was assumed in the
commit a1c55bccf6 ("drm/panel: lvds: Add support for the power-supply
property"), is actually returning an error pointer with -ENODEV instead of
NULL when there's no regulator to find.
Make sure we handle that case properly.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Fixes: a1c55bccf6 ("drm/panel: lvds: Add support for the power-supply property")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110155941.16109-1-maxime.ripard@free-electrons.com
A few fixes for 4.16:
- Cleanup the the remains of ttm io_mem_pfn
- A couple dpm quirks for SI
- Add Chunming as another amdgpu maintainer
- A few more huge page fixes
- A few other misc fixes
* 'drm-next-4.16' of git://people.freedesktop.org/~agd5f/linux:
drm/amd/pp: Implement get_max_high_clocks for CI/VI
MAINTAINERS: add David (Chunming) Zhou as additional amdgpu maintainer
drm/amdgpu: fix 64bit BAR detection
drm/amdgpu: optimize moved handling only when vm_debug is inactive
drm/amdgpu: simplify huge page handling
drm/amdgpu: update VM PDs after the PTs
drm/amdgpu: minor optimize VM moved handling v2
drm/amdgpu: loosen the criteria for huge pages a bit
drm/amd/powerplay: set pp_num_states as 0 on error situation
drm/ttm: specify DMA_ATTR_NO_WARN for huge page pools
drm/ttm: remove ttm_bo_default_io_mem_pfn
staging: remove the default io_mem_pfn set
drm/amd/powerplay: fix memory leakage when reload (v2)
drm/amdgpu/gfx9: only init the apertures used by KGD (v2)
drm/amdgpu: add atpx quirk handling (v2)
drm/amdgpu: Add dpm quirk for Jet PRO (v2)
drm/radeon: Add dpm quirk for Jet PRO (v2)
- Fix a KASAN reported use after free
- Whitelist a register to avoid hangs
- GVT fixes
-----BEGIN PGP SIGNATURE-----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=EmkE
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-fixes-2018-01-11-1' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Hopefully final drm/i915 fixes for v4.15:
- Fix a KASAN reported use after free
- Whitelist a register to avoid hangs
- GVT fixes
* tag 'drm-intel-fixes-2018-01-11-1' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Don't adjust priority on an already signaled fence
drm/i915: Whitelist SLICE_COMMON_ECO_CHICKEN1 on Geminilake.
drm/i915/gvt: Fix stack-out-of-bounds bug in cmd parser
drm/i915/gvt: Clear the shadow page table entry after post-sync
Two important fixes for vmwgfx.
The off-by-one fix could cause a malicious user to potentially crash the
kernel.
The framebuffer map cache fix can under some circumstances enable a user to
read from or write to freed pages.
* 'vmwgfx-fixes-4.15' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Potential off by one in vmw_view_add()
drm/vmwgfx: Don't cache framebuffer maps
The bulk of these changes are preparation work and addition of support
for Tegra186. Currently only HDMI output (the primary output on Jetson
TX2) is supported, but the hardware is also capable of doing DSI and
DisplayPort.
Tegra DRM now also uses the atomic commit helpers instead of the open-
coded variant that was only doing half its job. As a bit of a byproduct
of the Tegra186 support the driver also gained HDMI 2.0 as well as zpos
property support.
Along the way there are also a few patches to clean up a few things and
fix minor issues.
-----BEGIN PGP SIGNATURE-----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=FfXI
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.16-rc1-fixes' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.16-rc1
The bulk of these changes are preparation work and addition of support
for Tegra186. Currently only HDMI output (the primary output on Jetson
TX2) is supported, but the hardware is also capable of doing DSI and
DisplayPort.
Tegra DRM now also uses the atomic commit helpers instead of the open-
coded variant that was only doing half its job. As a bit of a byproduct
of the Tegra186 support the driver also gained HDMI 2.0 as well as zpos
property support.
Along the way there are also a few patches to clean up a few things and
fix minor issues.
* tag 'drm/tegra/for-4.16-rc1-fixes' of git://anongit.freedesktop.org/tegra/linux: (51 commits)
drm/tegra: dc: Properly cleanup overlay planes
drm/tegra: dc: Fix possible_crtcs mask for planes
drm/tegra: dc: Restore YUV overlay support
drm/tegra: dc: Implement legacy blending
drm/tegra: Correct timeout in tegra_syncpt_wait
drm/tegra: gem: Correct iommu_map_sg() error checking
drm/tegra: dc: Link DC1 to DC0 on Tegra20
drm/tegra: Fix non-debugfs builds
drm/tegra: dpaux: Keep reset defaults for hybrid pad parameters
drm/tegra: Mark Tegra186 display hub PM functions __maybe_unused
drm/tegra: Use IOMMU groups
gpu: host1x: Use IOMMU groups
drm/tegra: Implement zpos property
drm/tegra: dc: Remove redundant spinlock
drm/tegra: dc: Use direct offset to plane registers
drm/tegra: dc: Support more formats
drm/tegra: fb: Force alpha formats
drm/tegra: dpaux: Add Tegra186 support
drm/tegra: dpaux: Implement runtime PM
drm/tegra: sor: Support HDMI 2.0 modes
...
Updates for 4.16.. fairly small this time around, main thing is
devfreq support for the gpu.
* tag 'drm-msm-next-2018-01-10' of git://people.freedesktop.org/~robclark/linux:
drm/msm: Add devfreq support for the GPU
drm/msm/adreno: a5xx: Explicitly program the CP0 performance counter
drm/msm/adreno: Read the speed bins for a5xx targets
drm/msm/adreno: Move clock parsing to adreno_gpu_init()
drm/msm/adreno: Cleanup chipid parsing
drm/msm/gpu: Remove unused bus scaling code
drm/msm/adreno: Remove a useless call to dev_pm_opp_get_freq()
drm/msm/adreno: Call dev_pm_opp_put()
drm/msm: Fix NULL deref in adreno_load_gpu
drm/msm: gpu: Only sync fences on rings that exist
drm/msm: fix leak in failed get_pages
drm/msm: avoid false-positive -Wmaybe-uninitialized warning
drm/msm/mdp4: Deduplicate bus_find_device() by name matching
drm/msm: add missing MODULE_FIRMWARE declarations
drm/msm: update adreno firmware path in MODULE_FIRMWARE
drm/msm: free kstrdup'd cmdline
drm/msm: fix msm_rd_dump_submit prototype
drm/msm: fix spelling mistake: "ringubffer" -> "ringbuffer"
pci_get_bus_and_slot() is restrictive such that it assumes domain=0 as
where a PCI device is present. This restricts the device drivers to be
reused for other domain numbers.
Getting ready to remove pci_get_bus_and_slot() function in favor of
pci_get_domain_bus_and_slot().
Replace pci_get_bus_and_slot() with pci_get_domain_bus_and_slot()
and extract the domain number from
1. struct pci_dev
2. struct pci_dev through drm_device->pdev
3. struct pci_dev through fb->subdev->drm_device->pdev
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
pci_get_bus_and_slot() is restrictive such that it assumes domain=0 as
where a PCI device is present. This restricts the device drivers to be
reused for other domain numbers.
Getting ready to remove pci_get_bus_and_slot() function in favor of
pci_get_domain_bus_and_slot().
Add domain parameter to CDV_MSG_READ32, CDV_MSG_WRITE32, MRST_MSG_READ32,
MRST_MSG_WRITE32, MDFLD_MSG_READ32, MDFLD_MSG_WRITE32.
Extract pci_dev from struct drm_device and use pdev to find the domain
number while calling pci_get_domain_bus_and_slot().
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
It was only checking the divider when determing the closest match if
it could not match the requested rate exactly.
For a projector connected to an Olimex A20-OLinuXino-LIME using HDMI
with a native resolution of 1280x800 and pixel clock of 83.5 MHz, this
resulted in 1280x800 mode not being available and the following in dmesg
when the kernel is booted with drm.debug=0x3e:
[drm:drm_mode_debug_printmodeline] Modeline 37:"1280x800" 60 83500 1280 1352 1480 1680 800 810 816 831 0x48 0x5
[drm:drm_mode_prune_invalid] Not using 1280x800 mode: NOCLOCK
Fixes: 9c5681011a ("drm/sun4i: Add HDMI support")
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109020323.11852-4-net147@gmail.com
It is possible that if there is no exact rate match and
"rounded = clk_hw_round_rate(parent, ideal)" gives high enough values
(e.g. if rounded is 2 * ideal) that the condition
"abs(rate - rounded / i) < abs(rate - best_parent / best_div)" is never
met and best_parent is never set. This results in req->rate and
req->best_parent_rate being assigned 0.
To avoid this, we set best_parent to the first calculated rate if it is
unset. The sun4i_tmds_calc_divider function already has a similar check.
Fixes: 9c5681011a ("drm/sun4i: Add HDMI support")
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109020323.11852-2-net147@gmail.com
Geminilake requires the 3D driver to select whether barriers are
intended for compute shaders, or tessellation control shaders, by
whacking a "Barrier Mode" bit in SLICE_COMMON_ECO_CHICKEN1 when
switching pipelines. Failure to do this properly can result in GPU
hangs.
Unfortunately, this means it needs to switch mid-batch, so only
userspace can properly set it. To facilitate this, the kernel needs
to whitelist the register.
The workarounds page currently tags this as applying to Broxton only,
but that doesn't make sense. The documentation for the register it
references says the bit userspace is supposed to toggle only exists on
Geminilake. Empirically, the Mesa patch to toggle this bit appears to
fix intermittent GPU hangs in tessellation control shader barrier tests
on Geminilake; we haven't seen those hangs on Broxton.
v2: Mention WA #0862 in the comment (it doesn't have a name).
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180105085905.9298-1-kenneth@whitecape.org
(cherry picked from commit ab062639ed)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In case kfd_get_process_device_data returns null, there are some
null pointer dereferences in functions kfd_bind_processes_to_device
and kfd_unbind_processes_from_device.
Fix this by printing a WARN_ON for PDDs that aren't found and skip
them with continue statements.
Addresses-Coverity-ID: 1463794 ("Dereference null return value")
Addresses-Coverity-ID: 1463772 ("Dereference null return value")
Suggested-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
v2: add table length check.
DC component expect PP to give max engine clock and
memory clock through pp_get_display_mode_validation_clocks
on DGPU as well.
This patch can fix MultiGPU-Display blank
out with 1 IGPU-4k display and 2 DGPU-two 4K
displays.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Windows added by the BIOS are not marked as 64bit because they are
usually not changeable anyway.
This fixes large BAR support on my new Ryzen build system.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise we would completely circumvent that debugging feature.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Roger He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the PDEs after resetting the huge flag.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Necessary for the next patch.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Try to lock moved BOs if it's successful we can update the
PTEs directly to the new location.
v2: rebase
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can actually handle invalid huge pages perfectly fine now.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Suppress warning messages when allocating huge pages fails since we can
always fall back to normal pages.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No one will use this function except ttm_bo_io_mem_pfn() now, so move
the calculation of ttm_bo_default_io_mem_pfn() into ttm_bo_io_mem_pfn()
and do some cleanup.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add smu_free_memory when smu fini to prevent memory leakage
v2: squash in typo fix (Yintian) and warning (Harry)
Signed-off-by: Yintian Tao <yttao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use adev->vm_manager.id_mgr[0].num_ids rather than hardcoded 16.
v2: use AMDGPU_GFXHUB rather than hardcoded 0 (Christian)
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Noticed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add quirks for handling PX/HG systems. In this case, add
a quirk for a weston dGPU that only seems to properly power
down using ATPX power control rather than HG (_PR3).
v2: append a new weston XT
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com> (v2)
Reviewed-and-Tested-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Add support for devfreq to dynamically control the GPU frequency.
By default try to use the 'simple_ondemand' governor which can
adjust the frequency based on GPU load.
v2: Fix __aeabi_uldivmod issue from the 0 day bot and use
devfreq_recommended_opp() as suggested by Rob.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The vmw_view_cmd_to_type() function returns vmw_view_max (3) on error.
It's one element beyond the end of the vmw_view_cotables[] table.
My read on this is that it's possible to hit this failure. header->id
comes from vmw_cmd_check() and it's a user controlled number between
1040 and 1225 so we can hit that error. But I don't have the hardware
to test this code.
Fixes: d80efd5cb3 ("drm/vmwgfx: Initial DX support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: <stable@vger.kernel.org>
Even though the default countable for CP0 is CP_ALWAYS_COUNT (0),
program the selector during HW initialization in an effort to be
up front about which counters are programmed and why.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some 5xx based chipsets have different bins for GPU clock speeds.
Read the fuses (if applicable) and set the appropriate OPP table.
This will only work with OPP v2 tables - the bin will be ignored
for legacy pwrlevel tables.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Move the clock parsing to adreno_gpu_init() to allow for target
specific probing and manipulation of the clock tables.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We don't need to convert the chipid to an intermediate value and
then back again into a struct adreno_rev.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Remove the downstream bus scaling code. It isn't needed for for
compatibility with a downstream or vendor kernel. Get it out of the
way to clear space for devfreq support.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Calling dev_pm_opp_find_freq_floor() returns the matched frequency
in 'freq'. We don't need to call dev_pm_opp_get_freq() again
to get the frequency value.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We need to call dev_pm_opp_put() to put back the reference
for the OPP struct after calling the various dev_pm_opp_get_*
functions.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The SOR0 found on Tegra124 and Tegra210 only supports eDP and LVDS and
therefore has a slightly different clock tree than the SOR1 which does
not support eDP, but HDMI and DP instead.
Commit e1335e2f0c ("drm/tegra: sor: Reimplement pad clock") breaks
setups with eDP because the sor->clk_out clock is uninitialized and
therefore setting the parent clock (either the safe clock or either of
the display PLLs) fails, which can cause hangs later on since there is
no clock driving the module.
Fix this by falling back to the module clock for sor->clk_out on those
setups. This guarantees that the module will always be clocked by an
enabled clock and hence prevents those hangs.
Fixes: e1335e2f0c ("drm/tegra: sor: Reimplement pad clock")
Reported-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Buffer objects need to be either pinned or reserved while a map is active,
that's not the case here, so avoid caching the framebuffer map.
This will cause increasing mapping activity mainly when we don't do
page flipping.
This fixes occasional garbage filled screens when the framebuffer has been
evicted after the map.
Since in-kernel mapping of whole buffer objects is error-prone on 32-bit
architectures and also quite inefficient, we will revisit this later.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Cc: <stable@vger.kernel.org>
The newly added get_local_mem_info() function prints a phys_addr_t
using 0x%llx, which is wrong on most 32-bit systems, as shown by
this warning:
drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd.c: In function 'get_local_mem_info':
include/linux/kern_levels.h:5:18: error: format '%llx' expects argument of type 'long long unsigned int', but argument 2 has type 'resource_size_t {aka unsigned int}' [-Werror=format=]
drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd.c:297:31: note: format string is defined here
pr_debug("Address base: 0x%llx limit 0x%llx public 0x%llx private 0x%llx\n",
Passing the address by reference to the special %pap format string will
produce the correct output and avoid the warning.
Fixes: 30f1c0421e ("drm/amdgpu: Implement get_local_mem_info")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Last few updates for 4.16:
- Misc fixes for amdgpu
- Enable swapout for reserved BOs during allocation for ttm
- Misc cleanups for ttm
* 'drm-next-4.16' of git://people.freedesktop.org/~agd5f/linux: (24 commits)
drm/amdgpu: Correct the IB size of bo update mapping.
drm/ttm: enable swapout for reserved BOs during allocation
drm/ttm: add new function to check if bo is allowable to evict or swapout
drm/ttm: use an operation ctx for ttm_tt_bind
drm/ttm: use an operation ctx for ttm_tt_populate in ttm_bo_driver (v2)
drm/ttm: use an operation ctx for ttm_mem_global_alloc_page
drm/ttm: use an operation ctx for ttm_mem_global_alloc
drm/ttm: call ttm_bo_swapout directly when ttm shrink
drm/vmwgfx: remove the default io_mem_pfn set
drm/virtio: remove the default io_mem_pfn set
drm/radeon: remove the default io_mem_pfn set
drm/qxl: remove the default io_mem_pfn set
drm/nouveau: remove the default io_mem_pfn set
drm/mgag200: remove the default io_mem_pfn set
drm/cirrus: remove the default io_mem_pfn set
drm/bochs: remove the default io_mem_pfn set
drm/ast: remove the default io_mem_pfn set
drm/ttm: add ttm_bo_io_mem_pfn to check io_mem_pfn
drm/amdgpu: fix VM faults with per VM BOs
drm/ttm: drop the spin in delayed delete if the trylock doesn't work
...
The first overlay plane can leak if initialization of the second overlay
plane fails. Fix this by properly destroying the first overlay plane on
error.
Suggested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Cursor and overlay planes use a possible_crtcs mask based on the DC pipe
number. However, DRM requires each bit in the mask to correspond to the
index of the CRTC, which will be different from the DC pipe number for a
configuration where the first display controller is disabled, or where a
deferred probe leads to the first display controller being probed after
the first.
Suggested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit ebae8d0743 ("drm/tegra: dc: Implement legacy blending") broke
support for YUV overlays by accident. The reason is that YUV formats are
considered opaque because they have no alpha component, but on the other
hand no corresponding format with an alpha component can be returned. In
the case of YUV formats, the opaque format is the same as the alpha
format, so add the special case to restore YUV overlay support.
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Lyude Paul