This patch adds support for configuring the port multiplexer hardware
which resides in front of the GENET Ethernet MAC controller. This allows
us to support:
- internal PHYs (using drivers/net/phy/bcm7xxx.c)
- MoCA PHYs which are an entirely separate hardware block not covered
here
- external PHYs and switches
Note that MoCA and switches are currently supported using the emulated
"fixed PHY" driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the BCMGENET main driver file which supports the
following:
- GENET hardware from V1 to V4
- support for reading the UniMAC MIB counters statistics
- support for the 5 transmit queues
- support for RX/TX checksum offload and SG
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchs adds the bcmgenet.h header file which contains all the
hardware definitions for the GENETv1 to v4 hardware blocks as well as
the driver private structure and MIB counters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently multi-channel configuration is read via the QUERY_FW_CONFIG cmd.
This method has been deprecated by the Skyhawk-R FW. Instead,
GET_PROFILE_CONFIG::port-desc must be used to query this configuration.
This patch also:
a) introduces a few macros to identify certain categories of multi-channel
configs
2) re-factors the be_cmd_set_profile_config() code to be able to read any kind
of desc (and not just the nic-desc.)
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch logs a kernel message when a HW error(SLIPORT_ERROR in Lancer and UE
in BEx/Skyhawk) is detected. The log message for BE3 was missing earlier.
This patch also refactors the code by segregating error-detection and reporting
code for Lancer and BEx/SH.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver #define's and uses ETHERSMALL macro for the minimum Ethernet frame
size for which we have a standard macro ETH_ZLEN. Use the latter instead of
the home-grown one.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Respond better to a VF reset event. When a reset is signaled by the
PF, or detected by the watchdog task, prevent the watchdog from
processing admin queue requests, and schedule the reset task.
In the reset task, wait first for the reset to start, then for it to
complete, then reinit the driver.
If the reset never appears to complete after a long, long time (>10
seconds is possible depending on what's going on with the PF driver),
then set a flag to indicate that PF communications have failed.
If this flag is set, check for the reset to complete in the watchdog,
and attempt to do a full reinitialization of the driver from scratch.
With these changes the VF driver correctly handles a PF reset event
while running on bare metal, or in a VM.
Also update copyrights.
Change-ID: I93513efd0b50523a8345e7f6a33a5e4f8a2a5996
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Dan Carpenter (from Oracle), the flags variable is
declared as a 64-bit long but all of the flags are defined as u32,
which may lead to unintended consequences. Fix this by declaring flags
as u32 (since we don't need any more than about a dozen flags right
now), and remove the volatile qualifier, since it's unnecessary and
just makes checkpatch cry.
Change-ID: I137d3bb1842bf7e9456b5929ca54e3b0ed45dcab
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we store the traffic vector names in the queue vector struct, we
don't need to maintain an array of strings for these names in the
adapter structure. Replace this array with a single string and use it
when allocating the misc irq vector.
Also update copyrights.
Change-ID: I664f096c3c008210d6a04a487163e8aa934fee5b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Locate the structure in the correct header file.
Change-ID: Ic7853131728812093a44a75d6b70953311a48dab
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a bunch of unused structure members that are just wasting
space. Remove a completely unused info structure definition as well.
Also update copyrights.
Change-ID: I028ab92d9b7bd13a832cf3363bd1dc6610d8a535
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the DOWN flag before attempting to disable VFs when unloading the
driver. Also, don't attempt to reset the VFs when the driver is
unloading, because the switch configuration will fail. This fixes a
panic on unload when VFs are enabled.
Change-ID: I25a6567e89c9687145f510ff4f630932412c5c5d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If VFs are present when the driver loads, then set up some resources
so they can function.
Change-ID: I485916a811609a9990ce663d06dc645f625b07ff
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset all of the VFs after a PF reset, so that they are in a known
state, and the VF driver can detect the reset and reinit itself.
Change-ID: I93c5b3a0f8b1371d0da078f92de948b9d3a6413f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this, the VF can never communicate with the PF after a VF
reset.
Change-ID: I8d10f1d0d0638d50d39f0aff263422e05d83ad83
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This looks like a cut and paste error. The code makes no sense where
it is, and accomplishes nothing. Since we've removed the goto, we can
also get rid of the extraneous brackets.
Change-ID: I9315e3eafeee0a5713c94b0dc57b58b60a849124
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If tx_timeout recovery failed, then it becomes necessary to set
i40e_down bit before actually shutdown the connection.
Change-ID: Iaac81df0e302116571827aa0cff450697fbb7fa3
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As politely pointed out by Dave Miller, calls to memset do not need a
void pointer cast. Additionally, it is preferred to use sizeof(*the
actual object) instead of sizeof(type).
Change-ID: Id6a02429b7040111531f3865ea03fbe619167cb3
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change moves one operator up to the previous line and deletes
the duplicate declaration of ETH_ALEN.
Also update copyrights.
Change-ID: I88de73093b584e0f3b29d481ccd83fc4b1a1afa5
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver version to 0.3.31-k.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a spelling error, s/extention/extension/.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new firmware fixes following bugs:
1. HW attention appears and traffic stops when iSCSI firmware tries to
retransmit iSCSI login command when the iSCSI login is carrying data
not aligned to 4-bytes.
2. FCoE traffic fails to run when running in switch-independent multi-function
mode and there's more than one interface supporting FCoE on a given port.
3. While two ports are running FCoE with at least one of them has a function
number (>1) on the same engine in a 4-port device a zeroed CQE is given,
causing FCoE traffic to stop.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the various points where the driver use bit operations in order
to schedule the sp_rtnl_task from the code, adding a single utility function
that does it instead.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_panic_dump() prints all kind of driver information, including slowpath
information. Since VFs don't initialize slowpath information, a VF reaching
this flow will likely cause a panic in the system as it will access NULL
pointers.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several places in IOV related flows where PF needs to determine
whether a VF slowpath elements have already been configured (i.e., this
affect its ability to configure/remove classifications for the VF).
This patch changes the conditions for the validation and performs a cleaner
validation (e.g., by replacing several validations with a single one).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides PF-side support for VFs assigned to a VM running windows
2012 with the RSC feature enabled.
Signed-off-by: Michal Kalderon <michals@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is purely semantic - break the flow in which PF validates the VF
classification filtering requirement is valid into several sub-functions
for better readable code.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest FW performs this autonomously, makes this code surplus.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some debug prints (mostly iov/statistics related) which clobber
system logs whenever their verbosity level is set for an interface.
This patch puts harsher verbosity requirements for such debug prints to be
printed.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove trailing blank lines in several files.
Use only one blank line between functions.
Add a blank line as a separator in a few places.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't use 'Solarstorm' or 'Solarflare Communications' in full
any more.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions such as is_valid_ether_addr() expect u8 *, so use that
instead of char *.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allocate efx_channel structures with kzalloc() so we don't need to
zero-initialise individual fields in efx_probe_channel(). Further,
this function will be called again during DMA ring resizing and we
should not reset any statistics then.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EF10 implements option descriptors to switch TX checksum offload
on and off between packets. We could therefore use a single
hardware TX queue per kernel TX queue, although we don't yet.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These DMA descriptor types will only be used by the userland
networking stack.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is defined then NET_IP_ALIGN
will be defined as 0, so this macro is redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is substantial latency in generation and handling of PPS events
from the NIC, which we have to correct for before passing a host
timestamp to the PPS subsystem. We compare clocks with the MC,
giving us two offsets to subtract from the timestamp generated by
pps_get_ts():
(a) Time from the last good sync (where we got host and NIC timestamps
for nearly the same instant) to the time we called pps_get_ts()
(b) Time from NIC top of second to the last good sync
We currently calculate (a) + (b) in a quite confusing way.
Instead, calculate (a) completely, then add (b) to it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use conventional net_ratelimit() instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix for init time stack trace occuring in
alx_get_stats64 upon start up. Should have been part of
commit adding the spinlock:
f1b6b106 alx: add alx_get_stats64 operation
Signed-off-by: John Greene <jogreene@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove occurrences of unused struct __vxge_hw_device pointer in functions
vxge_learn_mac() and vxge_rem_isr().
Detected by Coverity: CID 139839, CID 139842.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused network device private data pointer 'vp' in function
vortex_eisa_cleanup(). Detected by Coverity: CID 139826.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ee45fd92c7 ("sfc: Use TX PIO
for sufficiently small packets") introduced the following warning:
drivers/net/ethernet/sfc/tx.c: In function 'efx_enqueue_skb':
drivers/net/ethernet/sfc/tx.c:432:1: warning: label 'finish_packet' defined but not used
Stick the label inside the same #ifdef that the code which calls
it uses. Note that this is only seen for arch that do not set
ARCH_HAS_IOREMAP_WC, such as arm, mips, sparc, ..., as the others
enable the write combining code and hence use the label.
Cc: Jon Cooper <jcooper@solarflare.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x driver uses incorrect PF identifier to configure (in HW) the VF
interrupt scheme; As a result, in multi-function mode the configuration
for PFs with a high index (4+) will overflow and the PF will erroneously
configure a single ISR scheme for its VFs.
As a result, if such a VF uses multiple queues, interrupt generation will
stop after VF receives an Rx packet or sends a Tx packet on a queue
other than queue[0].
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting David Vrabel -
"5780 cards cannot have jumbo frames and TSO enabled together. When
jumbo frames are enabled by setting the MTU, the TSO feature must be
cleared. This is done indirectly by calling netdev_update_features()
which will call tg3_fix_features() to actually clear the flags.
netdev_update_features() will also trigger a new netlink message for the
feature change event which will result in a call to tg3_get_stats64()
which deadlocks on the tg3 lock."
tg3_set_mtu() does not need to be under the tg3 lock since converting
the flags to use set_bit(). Move it out to after tg3_netif_stop().
Reported-by: David Vrabel <david.vrabel@citrix.com>
Tested-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original code, if tg3_readphy() fails then it does an unnecessary
check to verify "err" is still zero and then returns -EBUSY.
My static checker complains about the unnecessary "if (!err)" check and
anyway it is better to propagate the -EBUSY error code from
tg3_readphy() instead of hard coding it here. And really the original
code is confusing to look at.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Occasionally users want to know what parameters their Broadcom drivers
are running with. For example, a user may want to know if MSI is
disabled.
This patch has been compile tested.
Signed-off-by: James M Leddy <james.leddy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the ethernet driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring GRE tunnel using OVS, tcp stream is distributed over
all RSS queues which may cause TCP reordering. It happens since OVS
uses L2GRE protocol when kernel gre uses IPGRE.
Patch defaults gre tunnel to L2GRE which allows proper RSS for L2GRE
packets and (implicitly) disables RSS for IPGRE traffic.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MII management bus clock is derived from the MAC clock by dividing it by
MIIMODER register CLKDIV field value. This value may need to be set up
in case it is undefined or its default value is too high (and
communication with PHY is too slow) or too low (and communication with
PHY is impossible). The value of CLKDIV is not specified directly, but
is derived from the MAC clock for the default MII management bus frequency
of 2.5MHz. The MAC clock may be specified in the platform data, or in
the 'clocks' device tree attribute.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OpenCores 10/100 Mbps MAC does not support speeds above 100 Mbps, but does
not disable advertisement when PHY supports them. This results in
non-functioning network when the MAC is connected to a gigabit PHY connected
to a gigabit switch.
The fix is to disable gigabit speed advertisement on attached PHY
unconditionally.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX and RX rings share memory and descriptors. Maximal number of
descriptors reported is one less than the total available nuber of
descriptors. For the set operation the requested number of TX descriptors
is rounded down to the nearest power of two (driver logic requirement).
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following methods are implemented:
- get link state (standard implementation);
- get timestamping info (standard implementation).
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the GPIO bitbang MDIO driver is used instead of the Davinci MDIO driver
we need to configure the phy_id string differently. Otherwise this string
looks like this "gpio.6" instead of "gpio-0" and the PHY is not found when
phy_connect() is called.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Several fixups, of note:
1) Fix unlock of not held spinlock in RXRPC code, from Alexey
Khoroshilov.
2) Call pci_disable_device() from the correct shutdown path in bnx2x
driver, from Yuval Mintz.
3) Fix qeth build on s390 for some configurations, from Eugene
Crosser.
4) Cure locking bugs in bond_loadbalance_arp_mon(), from Ding
Tianhong.
5) Must do netif_napi_add() before registering netdevice in sky2
driver, from Stanislaw Gruszka.
6) Fix lost bug fix during merge due to code movement in ieee802154,
noticed and fixed by the eagle eyed Stephen Rothwell.
7) Get rid of resource leak in xen-netfront driver, from Annie Li.
8) Bounds checks in qlcnic driver are off by one, from Manish Chopra.
9) TPROXY can leak sockets when TCP early demux is enabled, fix from
Holger Eitzenberger"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
qeth: fix build of s390 allmodconfig
bonding: fix locking in bond_loadbalance_arp_mon()
tun: add device name(iff) field to proc fdinfo entry
DT: net: davinci_emac: "ti, davinci-no-bd-ram" property is actually optional
DT: net: davinci_emac: "ti, davinci-rmii-en" property is actually optional
bnx2x: Fix generic option settings
net: Fix warning on make htmldocs caused by skbuff.c
llc: remove noisy WARN from llc_mac_hdr_init
qlcnic: Fix loopback test failure
qlcnic: Fix tx timeout.
qlcnic: Fix initialization of vlan list.
qlcnic: Correct off-by-one errors in bounds checks
net: Document promote_secondaries
net: gre: use icmp_hdr() to get inner ip header
i40e: Add missing braces to i40e_dcb_need_reconfig()
xen-netfront: fix resource leak in netfront
net: 6lowpan: fixup for code movement
hyperv: Add support for physically discontinuous receive buffer
sky2: initialize napi before registering device
net: Fix memory leak if TPROXY used with TCP early demux
...
When user tried to change generic options using "ethtool -s" command, while SFP
module is plugged out or during module detection, the command would have failed
with "Unsupported port type" message. The fix is to ignore the port option in
case it's same as the current port configuration.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver was returning from link event handler without
setting linkup variable
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o __qlcnic_down call's netif_tx_disable which in turn stops
all the TX queues, corresponding start queue was missing in
__qlcnic_up which was leading to tx timeout.
o The commit b84caae486
(qlcnic: Fix usage of netif_tx_{wake, stop} api during link change.)
exposed this issue.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Do not re-initialize vlan list in case of adapter reset.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Bound checks should be >= instead of > for number of receive descriptors
and number of receive rings.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc updates from Ben Herrenschmidt:
"So here's my next branch for powerpc. A bit late as I was on vacation
last week. It's mostly the same stuff that was in next already, I
just added two patches today which are the wiring up of lockref for
powerpc, which for some reason fell through the cracks last time and
is trivial.
The highlights are, in addition to a bunch of bug fixes:
- Reworked Machine Check handling on kernels running without a
hypervisor (or acting as a hypervisor). Provides hooks to handle
some errors in real mode such as TLB errors, handle SLB errors,
etc...
- Support for retrieving memory error information from the service
processor on IBM servers running without a hypervisor and routing
them to the memory poison infrastructure.
- _PAGE_NUMA support on server processors
- 32-bit BookE relocatable kernel support
- FSL e6500 hardware tablewalk support
- A bunch of new/revived board support
- FSL e6500 deeper idle states and altivec powerdown support
You'll notice a generic mm change here, it has been acked by the
relevant authorities and is a pre-req for our _PAGE_NUMA support"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (121 commits)
powerpc: Implement arch_spin_is_locked() using arch_spin_value_unlocked()
powerpc: Add support for the optimised lockref implementation
powerpc/powernv: Call OPAL sync before kexec'ing
powerpc/eeh: Escalate error on non-existing PE
powerpc/eeh: Handle multiple EEH errors
powerpc: Fix transactional FP/VMX/VSX unavailable handlers
powerpc: Don't corrupt transactional state when using FP/VMX in kernel
powerpc: Reclaim two unused thread_info flag bits
powerpc: Fix races with irq_work
Move precessing of MCE queued event out from syscall exit path.
pseries/cpuidle: Remove redundant call to ppc64_runlatch_off() in cpu idle routines
powerpc: Make add_system_ram_resources() __init
powerpc: add SATA_MV to ppc64_defconfig
powerpc/powernv: Increase candidate fw image size
powerpc: Add debug checks to catch invalid cpu-to-node mappings
powerpc: Fix the setup of CPU-to-Node mappings during CPU online
powerpc/iommu: Don't detach device without IOMMU group
powerpc/eeh: Hotplug improvement
powerpc/eeh: Call opal_pci_reinit() on powernv for restoring config space
powerpc/eeh: Add restore_config operation
...
Indentation mismatch spotted with Coverity.
Introduced in 4e3b35b044 ("i40e: add DCB and DCBNL support")
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Submission d9aee59 "bnx2x: Don't release PCI bars on shutdown" separated
the PCI remove and shutdown flows, but pci_disable_device() is still
being called on both.
As a result, a dev_WARN_ONCE will be hit during shutdown for every bnx2x
VF probed on a hypervisor (as its shutdown callback will be called and later
pci_disable_sriov() will call its remove callback).
This calls the pci_disable_device() only on the remove flow.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logging the MAC address on every if-up, is not really useful, and annoying when
there is no cable inserted and NetworkManager tries the ifup every 50 seconds.
Also change the log level from warning to info, as that is what it is.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logging a PTP error on hw which simply does not support PTP is not very
useful. Moreover this message gets logged on every if-up, and if there is
no cable inserted NetworkManager will re-try the ifup every 50 seconds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/8390/apne.c: In function ‘apne_probe1’:
drivers/net/ethernet/8390/apne.c:215: warning: unused variable ‘ei_local’
Introduced by commit c45f812f02 ("8390 :
Replace ei_debug with msg_enable/NETIF_MSG_* feature"), which added the
variable without using it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
- Flow steering for InfiniBand UD traffic
- IP-based addressing for IBoE aka RoCE
- Pass SRP submaintainership from Dave to Bart
- SRP transport fixes from Bart
- Add the new Cisco usNIC low-level device driver
- Various other fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABCAAGBQJS4rzgAAoJEENa44ZhAt0hOL4P/jrNK2GeXqfzWIURL5MYtG9A
YK8xnRonlKQNo850E0WuC5wHCHqQ6Pqze+PL1rgR/MegNGrQ577qKo2eYumnMHSy
NO2BNhHa+5cUf04dXWOeJgyMTqo7CKwO7trZ6KwD+HFBAZqLDTFHPklH0qMI2bF6
U8HbKVslrvaDL3PywHop9Gxh9fWKY8ngw7LWPKkm5PQ0BFw8lZLOrGhWYr1MfJoY
iptf+wqehqlO8u7khfpo8tvar0hGbRYrUanx94RU/B5FbiQN936AXURtmbM+4MDD
o0QhzJKaaCmB1eYaeLsrEHyGcgAnifFPNzq/SLeRvL3TYIfMvTFWDECZDsdz0n5y
YuyuIQvs3FcbP9C014e2o8SXEfdJoR4Ht6XH2+wwDCD55t66ZnBHupYiVdYEJz09
UKBvvlY+v5cdzUmOeut21NgLHqQ/zpqWihfEFdTwXBNmKY27Ai9JILpFnrRCppYh
mawcEPKEXX1c0Adr1bXXsFBWhONgEOQFoth4FpVK31hJ1o2F9EyTZdLObcNHWcts
NdzOQ9S5UDcYN5OYfCM183cf/JmDBJB3Q01ms/1L2rhpLnoYA/Mj2BDzF+82FsMK
0BrPm7vX28a1mUVgLgpEpk1VEhJUJxzrmK8xogV9dU6vyGWmXPWhmBolLbPCx3SY
6dQ6u8v8tdl54CXStFuP
=wAWA
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.14:
- Flow steering for InfiniBand UD traffic
- IP-based addressing for IBoE aka RoCE
- Pass SRP submaintainership from Dave to Bart
- SRP transport fixes from Bart
- Add the new Cisco usNIC low-level device driver
- Various other fixes"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (75 commits)
IB/mlx5: Verify reserved fields are cleared
IB/mlx5: Remove old field for create mkey mailbox
IB/mlx5: Abort driver cleanup if teardown hca fails
IB/mlx5: Allow creation of QPs with zero-length work queues
mlx5_core: Fix PowerPC support
mlx5_core: Improve debugfs readability
IB/mlx5: Add support for resize CQ
IB/mlx5: Implement modify CQ
IB/mlx5: Make sure doorbell record is visible before doorbell
mlx5_core: Use mlx5 core style warning
IB/mlx5: Clear out struct before create QP command
mlx5_core: Fix out arg size in access_register command
RDMA/nes: Slight optimization of Ethernet address compare
IB/qib: Fix QP check when looping back to/from QP1
RDMA/cxgb4: Fix gcc warning on 32-bit arch
IB/usnic: Remove unused includes of <linux/version.h>
RDMA/amso1100: Add check if cache memory was allocated before freeing it
IPoIB: Report operstate consistently when brought up without a link
IB/core: Fix unused variable warning
RDMA/cma: Handle global/non-linklocal IPv6 addresses in cma_check_linklocal()
...
The adapter is freed before we check its flags. It was caused
by commit 144be3d ("net/cxgb4: Avoid disabling PCI device for
towice"). The problem was reported by Intel's "0-day" tool.
The patch fixes it to avoid reverting commit 144be3d.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Refactored MSI-x vector calculation for All adapters.
Decoupled logic in the code which was using same call to
request MSI-x vectors in default driver load, as well as
during set_channel() operation for TSS/RSS. This refactoring
simplifies code for TSS/RSS code path as well as probe path
of the driver load for all adapters.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Refactor configuration of interrupt coalescing parameters for
all supported adapters.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for MSI/MSI-X mode in poll controller routine.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Added hardware ops for interrupt enable/disable functions
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Dump each Tx queue details with all descriptors, queue indices
and Tx queue stats to imporve data colletion in situations
where Tx timeout occurs.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Use boolean type instead of u8.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of a workaround for a hardware erratum in the SFC9100 family
(SF bug 35388), the TX_DESC_UPD_DWORD register address is also used
for communicating with the event block, and only descriptor pointer
values < 2048 are valid.
If the TX DMA ring size is increased to 4096 descriptors (which the
firmware still allows) then we may write a descriptor pointer
value >= 2048, which has entirely different and undesirable effects!
Limit the TX DMA ring size correctly when this workaround is in
effect.
Fixes: 8127d661e7 ('sfc: Add support for Solarflare SFC9100 family')
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this situation then ARRAY_SIZE() and sizeof() are the same, but we're
really dealing with array indexes and not byte offsets so ARRAY_SIZE()
is cleaner.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We possibly retrieve the adapter's statistics during EEH recovery
and that should be disallowed. Otherwise, it would possibly incur
replicate EEH error and EEH recovery is going to fail eventually.
The patch reuses statistics lock and checks net_device is attached
before going to retrieve statistics, so that the problem can be
avoided.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have EEH error happens to the adapter and we have to remove
it from the system for some reasons (e.g. more than 5 EEH errors
detected from the device in last hour), the adapter will be disabled
for towice separately by eeh_err_detected() and remove_one(), which
will incur following unexpected backtrace. The patch tries to avoid
it.
WARNING: at drivers/pci/pci.c:1431
CPU: 12 PID: 121 Comm: eehd Not tainted 3.13.0-rc7+ #1
task: c0000001823a3780 ti: c00000018240c000 task.ti: c00000018240c000
NIP: c0000000003c1e40 LR: c0000000003c1e3c CTR: 0000000001764c5c
REGS: c00000018240f470 TRAP: 0700 Not tainted (3.13.0-rc7+)
MSR: 8000000000029032 <SF,EE,ME,IR,DR,RI> CR: 28000024 XER: 00000004
CFAR: c000000000706528 SOFTE: 1
GPR00: c0000000003c1e3c c00000018240f6f0 c0000000010fe1f8 0000000000000035
GPR04: 0000000000000000 0000000000000000 00000000003ae509 0000000000000000
GPR08: 000000000000346f 0000000000000000 0000000000000000 0000000000003fef
GPR12: 0000000028000022 c00000000ec93000 c0000000000c11b0 c000000184ac3e40
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR24: 0000000000000000 c0000000009398d8 c00000000101f9c0 c0000001860ae000
GPR28: c000000182ba0000 00000000000001f0 c0000001860ae6f8 c0000001860ae000
NIP [c0000000003c1e40] .pci_disable_device+0xd0/0xf0
LR [c0000000003c1e3c] .pci_disable_device+0xcc/0xf0
Call Trace:
[c0000000003c1e3c] .pci_disable_device+0xcc/0xf0 (unreliable)
[d0000000073881c4] .remove_one+0x174/0x320 [cxgb4]
[c0000000003c57e0] .pci_device_remove+0x60/0x100
[c00000000046396c] .__device_release_driver+0x9c/0x120
[c000000000463a20] .device_release_driver+0x30/0x60
[c0000000003bcdb4] .pci_stop_bus_device+0x94/0xd0
[c0000000003bcf48] .pci_stop_and_remove_bus_device+0x18/0x30
[c00000000003f548] .pcibios_remove_pci_devices+0xa8/0x140
[c000000000035c00] .eeh_handle_normal_event+0xa0/0x3c0
[c000000000035f50] .eeh_handle_event+0x30/0x2b0
[c0000000000362c4] .eeh_event_handler+0xf4/0x1b0
[c0000000000c12b8] .kthread+0x108/0x130
[c00000000000a168] .ret_from_kernel_thread+0x5c/0x74
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not continue with cleanup flow. If this ever happens we can check which
resources remained open.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
1. Fix derivation of sub-page index from the dma address in free_4k.
2. Fix the DMA address passed to dma_unmap_page by masking it properly.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use strings to display transport service or state of QPs. Use numeric
value for MTU of a QP.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Implement resize CQ which is a mandatory verb in mlx5.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Modify CQ is used by ULPs like IPoIB to change moderation parameters. This
patch adds support in mlx5.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use mlx5_core_warn(), which is the standard warning emitter function, instead
of pr_warn().
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Output structs are expected by firmware to be cleared when a command is called.
Clear the "out" struct instead of "dout" which is used only later.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The output size should be the sum of the core access reg output struct
plus the size of the specific register data provided by the caller.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Florian Fainelli