I noticed that I couldn't read the PCH temperature on my workstation
(C620 series chipset, w/ 2x Xeon Gold 5215 CPUs) directly, but had to go
through IPMI. Looking at the data sheet, it looks to me like the
existing intel PCH thermal driver should work without changes for
Lewisburg.
I suspect there's some other PCI IDs missing. But I hope somebody at
Intel would have an easier time figuring that out than I...
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/lkml/20200115184415.1726953-1-andres@anarazel.de/
Signed-off-by: Andres Freund <andres@anarazel.de>
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201113204916.1144907-1-andres@anarazel.de
It has been observed that on OMAP4430 (ES2.0, ES2.1 and ES2.3) the enabled
notifier causes errors on the DTEMP readout values:
ti-soc-thermal 4a002260.bandgap: in range ADC val: 52
ti-soc-thermal 4a002260.bandgap: in range ADC val: 64
ti-soc-thermal 4a002260.bandgap: in range ADC val: 64
ti-soc-thermal 4a002260.bandgap: out of range ADC val: 0
thermal thermal_zone0: failed to read out thermal zone (-5)
ti-soc-thermal 4a002260.bandgap: out of range ADC val: 0
thermal thermal_zone0: failed to read out thermal zone (-5)
ti-soc-thermal 4a002260.bandgap: out of range ADC val: 4
thermal thermal_zone0: failed to read out thermal zone (-5)
ti-soc-thermal 4a002260.bandgap: in range ADC val: 100
raw 100 translates to 133 Celsius on omap4-sdp, triggering shutdown due to
critical temperature.
When the notifier is disable for OMAP4430 the DTEMP values are stable:
ti-soc-thermal 4a002260.bandgap: in range ADC val: 56
ti-soc-thermal 4a002260.bandgap: in range ADC val: 56
ti-soc-thermal 4a002260.bandgap: in range ADC val: 57
ti-soc-thermal 4a002260.bandgap: in range ADC val: 57
ti-soc-thermal 4a002260.bandgap: in range ADC val: 56
Fixes: 5093402e5b ("thermal: ti-soc-thermal: Enable addition power management")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201029100335.27665-1-peter.ujfalusi@ti.com
If state has not changed successfully and we updated cpufreq_state,
next time when the new state is equal to cpufreq_state (not changed
successfully last time), we will return directly and miss a
freq_qos_update_request() that should have been.
Fixes: 5130802ddb ("thermal: cpu_cooling: Switch to QoS requests for freq limits")
Cc: v5.4+ <stable@vger.kernel.org> # v5.4+
Signed-off-by: Zhuguangqing <zhuguangqing@xiaomi.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201106092243.15574-1-zhuguangqing83@gmail.com
Function thermal_add_hwmon_sysfs, hwmon will be NULL when
new_hwmon_device = 0, so there is no need to check, kfree will
handle NULL point.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201102023121.3312-1-bernard@vivo.com
The bitmap_* API is the standard way to access data in the bitfield.
So convert irq_ack to return an unsigned long, and make things to use
bitmap API.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201109114624.23035-1-frank@allwinnertech.com
When system tries to enter S0ix suspend state, just after active load
scenarios, it fails due to PCH current temperature is higher than set
threshold.
This patch introduces delay loop mechanism that allows PCH temperature
to go down below threshold during suspend so it won't fail to enter S0ix.
Add delay loop timeout and count as module parameters for user to tune it,
if required based on system design. This change notifies the different
warning messages like when PCH temperature above the threshold and
executing delay loop. Also, notify the messages when it success or
failure for S0ix entry.
Previously out of 1000 runs around 3 to 5 times it might fail to enter
S0ix just after heavy workload. With this change, S0ix failures reduced
as PCH cools down below threshold.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201106170633.20838-1-sumeet.r.pawnikar@intel.com
MT8516 does not support thermal reset. Use device_reset_optional
instead of device_reset.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201021164231.3029956-3-fparent@baylibre.com
On RT or even on mainline with 'threadirqs' on the command line all
interrupts which are not explicitly requested with IRQF_NO_THREAD
run their handlers in thread context. The same applies to soft interrupts.
That means they are subject to the normal scheduler rules and no other
code is going to acquire that lock from hard interrupt context either,
so the irqsave() here is pointless in all cases.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1603760790-37748-1-git-send-email-tiantao6@hisilicon.com
The trip points are checked one by one with multiple condition
branches where one condition is enough to disable the trip point.
Merge all these conditions in a single 'OR' statement.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201027013743.62392-1-bernard@vivo.com
[dlezcano] Changed patch description
Since the power actor section has one function power_actor_set_power()
move it into Intelligent Power Allocation (IPA). There is no other user
of that helper function. It would also allow to remove the check of
cdev_is_power_actor() because the code which calls it in IPA already does
the needed check. Make the function static since only IPA use it.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201015112441.4056-5-lukasz.luba@arm.com
Since the Intelligent Power Allocation (IPA) uses different way to get
minimum and maximum power for a given cooling device, the helper functions
are not needed. There is no other code which uses them, so remove the
helper functions.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201015112441.4056-4-lukasz.luba@arm.com
The thermal cooling device specified in DT might be instantiated for
a thermal zone trip point with a limited set of OPPs to operate on. This
configuration should be supported by Intelligent Power Allocation (IPA),
since it is a standard for other governors. Change the code and allow IPA
to get power value of lower and upper bound set for a given cooling
device.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201015112441.4056-3-lukasz.luba@arm.com
The upper and lower limits of thermal throttle state in the
DT do not apply to the Intelligent Power Allocation (IPA) governor.
Add the clamping for cooling device upper and lower limits in the
power_actor_set_power() used by IPA.
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201007024332.30322-1-michael.kao@mediatek.com
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Conversion done using the script at:
https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use dev_error_probe() to simplify the error handling on imx and imx8
platforms (Anson Huang)
- Use dedicated kobj_to_dev() instead of container_of() in the sysfs
core code (Tian Tao)
- Fix coding style by adding braces to a one line conditional
statement on rcar (Geert Uytterhoeven)
- Add DT binding documentation for the r8a774e1 platform and update
the Kconfig description supporting RZ/G2 SoCs (Lad Prabhakar)
- Simplify the return expression of stm_thermal_prepare on the stm32
platform (Qinglang Miao)
- Fix the unit in the function documentation for the idle injection
cooling device (Zhuguang Qing)
- Remove an unecessary mutex_init() in the core code (Qinglang Miao)
- Add support for keep alive events in the core code and the specific
int340x (Srinivas Pandruvada)
- Remove unused thermal zone variable in devfreq and cpufreq cooling
devices (Zhuguang Qing)
- Add the A100's THS controller support (Yangtao Li)
- Add power management on the omap3's bandgap sensor (Adam Ford)
- Fix a missing nlmsg_free in the netlink core error path (Jing Xiangfeng)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl+GwbYACgkQqDIjiipP
6E8IFAf/UnO1HqfK96FnVJXx5ClXFE8PQhdVejxBEsNCJqUOwlqfpyONy7mgwABb
EuOvp5ZLX6ly9xG6J4NJhE4gN4DxqRKe0S3bQMU+DX8TQHc3otDKHILJbHrJdOY+
BYZpGxuCjU9yZrsJopztZIcpG7cF78d39XCJVSrBhoOBqPLXNGZkUUzOv9+QQti3
ipdhqB3kUzkgDFgIrDxX8t0vybQZSbiRWNUGrw/WQjMsG0NGIarCUHW4wiaea6gU
L2x1QDR5h9hxEAJiTBarOtF7ZlE15fpria0mWfTgmNMArMEtRBL60kBnmYa4o3EG
CseR7x1MdTCSqLCzKGfQyKv5SFgnVg==
=P6zv
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Fix Kconfig typo "acces" -> "access" (Colin Ian King)
- Use dev_error_probe() to simplify the error handling on imx and imx8
platforms (Anson Huang)
- Use dedicated kobj_to_dev() instead of container_of() in the sysfs
core code (Tian Tao)
- Fix coding style by adding braces to a one line conditional statement
on rcar (Geert Uytterhoeven)
- Add DT binding documentation for the r8a774e1 platform and update the
Kconfig description supporting RZ/G2 SoCs (Lad Prabhakar)
- Simplify the return expression of stm_thermal_prepare on the stm32
platform (Qinglang Miao)
- Fix the unit in the function documentation for the idle injection
cooling device (Zhuguang Qing)
- Remove an unecessary mutex_init() in the core code (Qinglang Miao)
- Add support for keep alive events in the core code and the specific
int340x (Srinivas Pandruvada)
- Remove unused thermal zone variable in devfreq and cpufreq cooling
devices (Zhuguang Qing)
- Add the A100's THS controller support (Yangtao Li)
- Add power management on the omap3's bandgap sensor (Adam Ford)
- Fix a missing nlmsg_free in the netlink core error path (Jing
Xiangfeng)
* tag 'thermal-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal: core: Adding missing nlmsg_free() in thermal_genl_sampling_temp()
thermal: ti-soc-thermal: Enable addition power management
thermal: sun8i: Add A100's THS controller support
thermal: sun8i: add TEMP_CALIB_MASK for calibration data in sun50i_h6_ths_calibrate
dt-bindings: thermal: sun8i: Add binding for A100's THS controller
thermal: cooling: Remove unused variable *tz
thermal: int340x: Add keep alive response method
thermal: core: Add new event for sending keep alive notifications
thermal: int340x: Provide notification for OEM variable change
thermal: core: remove unnecessary mutex_init()
thermal/idle_inject: Fix comment of idle_duration_us and name of latency_ns
thermal: Kconfig: Update description for RCAR_GEN3_THERMAL config
thermal: stm32: simplify the return expression of stm_thermal_prepare()
dt-bindings: thermal: rcar-gen3-thermal: Add r8a774e1 support
thermal: rcar_thermal: Add missing braces to conditional statement
thermal: Use kobj_to_dev() instead of container_of()
thermal: imx8mm: Use dev_err_probe() to simplify error handling
thermal: imx: Use dev_err_probe() to simplify error handling
drivers: thermal: Kconfig: fix spelling mistake "acces" -> "access"
thermal_genl_sampling_temp() misses to call nlmsg_free() in an error path.
Jump to out_free to fix it.
Fixes: 1ce50e7d40 ("thermal: core: genetlink support for events/cmd/sampling")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200929082652.59876-1-jingxiangfeng@huawei.com
The bandgap sensor can be idled when the processor is too, but it
isn't currently being done, so the power consumption of OMAP3
boards can elevated if the bangap sensor is enabled.
This patch attempts to use some additional power management
to idle the clock to the bandgap when not needed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Andreas Kemnade <andreas@kemnade.info> # GTA04
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200911123157.759379-1-aford173@gmail.com
For sun50i_h6_ths_calibrate(), the data read from nvmem needs a round of
calculation. On the other hand, the newer SOC may store other data in
the space other than 12bit sensor data. Add mask operation to read data
to avoid conversion error.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/dcf98648c16aff7649ff82438bfce6caae3e176f.1595572867.git.frank@allwinnertech.com
1. devfreq_cooling.c: The variable *tz is not used in
devfreq_cooling_get_requested_power(), devfreq_cooling_state2power()
and devfreq_cooling_power2state().
2. cpufreq_cooling.c: After 84fe2cab48, the variable *tz is not used
anymore in cpufreq_get_requested_power(), cpufreq_state2power() and
cpufreq_power2state().
Remove the variable *tz.
Signed-off-by: zhuguangqing <zhuguangqing@xiaomi.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200914071101.13575-1-zhuguangqing83@gmail.com
When firmware requests keep alive response, send an event to user space
to confirm by using imok sysfs entry.
Create a new sysf entry called "imok". User space can write an integer,
which results in execution of IMOK ACPI method of INT3400 thermal zone
device. This results in sending response to firmware request for keep
alive.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200915223650.406046-4-srinivas.pandruvada@linux.intel.com
When we receive ACPI notification for OEM variable change pass the
notification to user space handler. This will avoid polling for
OEM variable change from user space.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200915223650.406046-2-srinivas.pandruvada@linux.intel.com
The mutex poweroff_lock is initialized statically. It is
unnecessary to initialize by mutex_init().
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200916062139.191233-1-miaoqinglang@huawei.com
According to Documentation/process/coding-style.rst, if one branch of a
conditional statement needs braces, both branches should use braces.
Fixes: bbcf90c064 ("thermal: Explicitly enable non-changing thermal zone devices")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200819092716.3191-1-geert+renesas@glider.be
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1597129185-8460-2-git-send-email-Anson.Huang@nxp.com
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1597129185-8460-1-git-send-email-Anson.Huang@nxp.com
Bulk of the genetlink users can use smaller ops, move them.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to add maxattr and policy back to genl_ops, to enable
dumping per command policy to user space. This, however, would
cause bloat for all the families with global policies. Introduce
smaller version of ops (half the size of genl_ops). Translate
these smaller ops into a full blown struct before use in the
core.
v1:
- use struct assignment
- put a full copy of the op in struct genl_dumpit_info
- s/light/small/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
resulting from an incorrect ADC conversion are too high and fire an
emergency shutdown (Tony Lindgren)
- Don't suppress negative temp for qcom spmi as they are valid and
userspace needs them (Veera Vegivada)
- Fix use-after-free in thermal_zone_device_unregister reported by
Kasan (Dmitry Osipenko)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl9SDqQACgkQqDIjiipP
6E9/qwf/WybOihgjeQUv3a9f4k6SeJphoDZRNATJtyU1e+fgJXUxjFqma6t4CYJv
uphZ1SppY9rnx1nWzhANSQjKun5KLwIskcNTCaGN4adRJ1cNdY63PdSX9BTJr9+H
w5H0AGWMErAOdmCPCro4pnZ3l3FPKXcoNvqDAjF1kZ97v5tMGzdInflOJl1ztUZA
scAnY7j0TyNsoRy2TV0oxQtSN9cDhgph1zJF1RcVzlU1uD897Htet1RF/PrHDvBW
NYVcWDTfiWmvf9Zewy2+cfApK9QGqBRhnwt4Z8PlTUcqrOgqAiNnOAnov+Topg/y
XNQzWwXFUip6bk5pTXPF8gSI0glkJg==
=LDGk
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal fixes from Daniel Lezcano:
- Fix bogus thermal shutdowns for omap4430 where bogus values resulting
from an incorrect ADC conversion are too high and fire an emergency
shutdown (Tony Lindgren)
- Don't suppress negative temp for qcom spmi as they are valid and
userspace needs them (Veera Vegivada)
- Fix use-after-free in thermal_zone_device_unregister reported by
Kasan (Dmitry Osipenko)
* tag 'thermal-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal: core: Fix use-after-free in thermal_zone_device_unregister()
thermal: qcom-spmi-temp-alarm: Don't suppress negative temp
thermal: ti-soc-thermal: Fix bogus thermal shutdowns for omap4430
The user-after-free bug in thermal_zone_device_unregister() is reported by
KASAN. It happens because struct thermal_zone_device is released during of
device_unregister() invocation, and hence the "tz" variable shouldn't be
touched by thermal_notify_tz_delete(tz->id).
Fixes: 55cdf0a283 ("thermal: core: Add notifications call in the framework")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200817235854.26816-1-digetx@gmail.com
Currently driver is suppressing the negative temperature
readings from the vadc. Consumers of the thermal zones need
to read the negative temperature too. Don't suppress the
readings.
Fixes: c610afaa21 ("thermal: Add QPNP PMIC temperature alarm driver")
Signed-off-by: Veera Vegivada <vvegivad@codeaurora.org>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/944856eb819081268fab783236a916257de120e4.1596040416.git.gurus@codeaurora.org
We can sometimes get bogus thermal shutdowns on omap4430 at least with
droid4 running idle with a battery charger connected:
thermal thermal_zone0: critical temperature reached (143 C), shutting down
Dumping out the register values shows we can occasionally get a 0x7f value
that is outside the TRM listed values in the ADC conversion table. And then
we get a normal value when reading again after that. Reading the register
multiple times does not seem help avoiding the bogus values as they stay
until the next sample is ready.
Looking at the TRM chapter "18.4.10.2.3 ADC Codes Versus Temperature", we
should have values from 13 to 107 listed with a total of 95 values. But
looking at the omap4430_adc_to_temp array, the values are off, and the
end values are missing. And it seems that the 4430 ADC table is similar
to omap3630 rather than omap4460.
Let's fix the issue by using values based on the omap3630 table and just
ignoring invalid values. Compared to the 4430 TRM, the omap3630 table has
the missing values added while the TRM table only shows every second
value.
Note that sometimes the ADC register values within the valid table can
also be way off for about 1 out of 10 values. But it seems that those
just show about 25 C too low values rather than too high values. So those
do not cause a bogus thermal shutdown.
Fixes: 1a31270e54 ("staging: omap-thermal: add OMAP4 data structures")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200706183338.25622-1-tony@atomide.com
- Make better attempt at matching device with the correct OF node
- Allow batch removal of hierarchical sub-devices
- New Drivers
- Add STM32 Clocksource driver
- Add support for Khadas System Control Microcontroller
- Driver Removal
- Remove unused driver for TI's SMSC ECE1099
- New Device Support
- Add support for Intel Emmitsburg PCH to Intel LPSS PCI
- Add support for Intel Tiger Lake PCH-H to Intel LPSS PCI
- Add support for Dialog DA revision to Dialog DA9063
- New Functionality
- Add support for AXP803 to be probed by I2C
- Fix-ups
- Numerous W=1 warning fixes
- Device Tree changes; stm32-lptimer, gateworks-gsc, khadas,mcu, stmfx, cros-ec, j721e-system-controller
- Enabled Regmap 'fast I/O'; stm32-lptimer
- Change BUG_ON to WARN_ON; arizona-core
- Remove superfluous code/initialisation; madera, max14577
- Trivial formatting/spelling issues; madera-core, madera-i2c, da9055, max77693-private
- Switch to of_platform_populate(); sprd-sc27xx-spi
- Expand out set/get brightness/pwm macros; lm3533-ctrlbank
- Disable IRQs on suspend; motorola-cpcap
- Clean-up error handling; intel_soc_pmic_mrfld
- Ensure correct removal order of sub-devices; madera
- Many s/HTTP/HTTPS/ link changes
- Ensure name used with Regmap is unique; syscon
- Bug Fixes
- Properly 'put' clock on unbind and error; arizona-core
- Fix revision handling; da9063
- Fix 'assignment of read-only location' error; kempld-core
- Avoid using the Regmap API when atomic; rn5t618
- Redefine volatile register description; rn5t618
- Use locking to protect event handler; dln2
-----BEGIN PGP SIGNATURE-----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=X/Zn
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks
- Make better attempt at matching device with the correct OF node
- Allow batch removal of hierarchical sub-devices
New Drivers
- Add STM32 Clocksource driver
- Add support for Khadas System Control Microcontroller
Driver Removal
- Remove unused driver for TI's SMSC ECE1099
New Device Support
- Add support for Intel Emmitsburg PCH to Intel LPSS PCI
- Add support for Intel Tiger Lake PCH-H to Intel LPSS PCI
- Add support for Dialog DA revision to Dialog DA9063
New Functionality
- Add support for AXP803 to be probed by I2C
Fix-ups
- Numerous W=1 warning fixes
- Device Tree changes (stm32-lptimer, gateworks-gsc, khadas,mcu, stmfx, cros-ec, j721e-system-controller)
- Enabled Regmap 'fast I/O' in stm32-lptimer
- Change BUG_ON to WARN_ON in arizona-core
- Remove superfluous code/initialisation (madera, max14577)
- Trivial formatting/spelling issues (madera-core, madera-i2c, da9055, max77693-private)
- Switch to of_platform_populate() in sprd-sc27xx-spi
- Expand out set/get brightness/pwm macros in lm3533-ctrlbank
- Disable IRQs on suspend in motorola-cpcap
- Clean-up error handling in intel_soc_pmic_mrfld
- Ensure correct removal order of sub-devices in madera
- Many s/HTTP/HTTPS/ link changes
- Ensure name used with Regmap is unique in syscon
Bug Fixes
- Properly 'put' clock on unbind and error in arizona-core
- Fix revision handling in da9063
- Fix 'assignment of read-only location' error in kempld-core
- Avoid using the Regmap API when atomic in rn5t618
- Redefine volatile register description in rn5t618
- Use locking to protect event handler in dln2"
* tag 'mfd-next-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (76 commits)
mfd: syscon: Use a unique name with regmap_config
mfd: Replace HTTP links with HTTPS ones
mfd: dln2: Run event handler loop under spinlock
mfd: madera: Improve handling of regulator unbinding
mfd: mfd-core: Add mechanism for removal of a subset of children
mfd: intel_soc_pmic_mrfld: Simplify the return expression of intel_scu_ipc_dev_iowrite8()
mfd: max14577: Remove redundant initialization of variable current_bits
mfd: rn5t618: Fix caching of battery related registers
mfd: max77693-private: Drop a duplicated word
mfd: da9055: pdata.h: Drop a duplicated word
mfd: rn5t618: Make restart handler atomic safe
mfd: kempld-core: Fix 'assignment of read-only location' error
mfd: axp20x: Allow the AXP803 to be probed by I2C
mfd: da9063: Add support for latest DA silicon revision
mfd: da9063: Fix revision handling to correctly select reg tables
dt-bindings: mfd: st,stmfx: Remove I2C unit name
dt-bindings: mfd: ti,j721e-system-controller.yaml: Add J721e system controller
mfd: motorola-cpcap: Disable interrupt for suspend
mfd: smsc-ece1099: Remove driver
mfd: core: Add OF_MFD_CELL_REG() helper
...
We just don't do that. "default y" is for things that are needed for
compatibility (when an old feature is made unconditional), or for things
that are basically part of the infrastructure of a platform.
And it can possibly be used for questions that don't enable code on
their own, but are used to enable or disable a whole slew of other
questions.
A new feature that people aren't using is never 'default y', unless it
cures cancer or ends world hunger.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers cleanup (Andrzej Pietrasiewicz)
- Add generic netlink support for userspace notifications: events, temperature
and discovery commands (Daniel Lezcano)
- Fix redundant initialization for a ret variable (Colin Ian King)
- Remove the clock cooling code as it is used nowhere (Amit Kucheria)
- Add the rcar_gen3_thermal's r8a774e1 support (Marian-Cristian Rotariu)
- Replace all references to thermal.txt in the documentation to the
corresponding yaml files (Amit Kucheria)
- Add maintainer entry for the IPA (Lukasz Luba)
- Add support for MSM8939 for the tsens (Shawn Guo)
- Update power allocator and devfreq cooling to SPDX licensing (Lukasz Luba)
- Add Cannon Lake Low Power PCH support (Sumeet Pawnikar)
- Add tsensor support for V2 mediatek thermal system (Henry Yen)
- Fix thermal zone lookup by ID for the core code (Thierry Reding)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl8q7tsACgkQqDIjiipP
6E+5Rwf7BFEn5YXPvng8cmnAlgvEBc9DdT6mGSo0NpFm9MdUxXlaqvw3WWSGyqWQ
+z0Ka7lmn5XyiMsVN11++Snp+79X17HzZf9SXO3glyIpAn+5prTDRhzzj0/jPrtS
sEeI++DrILsKKMGVljzftLmwNJN9DkUDNcnmWmZdCDbYVEKtP9Pjf2wBjAnXj7sX
JA3CkHRMwYLEQbfaKz37M11cYM+LqbDOlb6U11YWgAGGJ7d7zNYRf2/YSYPM4AN6
iE6j0E+3jIlXesULsap1AzeJaBq+wFxj1FL2TUZ8KscvRrm3AucqzNAT2M/Bc5Az
XLKKzc6Gp9JfqB5KXhX2EDu7VRnDBg==
=cSMN
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Add support to enable/disable the thermal zones resulting on core
code and drivers cleanup (Andrzej Pietrasiewicz)
- Add generic netlink support for userspace notifications: events,
temperature and discovery commands (Daniel Lezcano)
- Fix redundant initialization for a ret variable (Colin Ian King)
- Remove the clock cooling code as it is used nowhere (Amit Kucheria)
- Add the rcar_gen3_thermal's r8a774e1 support (Marian-Cristian
Rotariu)
- Replace all references to thermal.txt in the documentation to the
corresponding yaml files (Amit Kucheria)
- Add maintainer entry for the IPA (Lukasz Luba)
- Add support for MSM8939 for the tsens (Shawn Guo)
- Update power allocator and devfreq cooling to SPDX licensing (Lukasz
Luba)
- Add Cannon Lake Low Power PCH support (Sumeet Pawnikar)
- Add tsensor support for V2 mediatek thermal system (Henry Yen)
- Fix thermal zone lookup by ID for the core code (Thierry Reding)
* tag 'thermal-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (40 commits)
thermal: intel: intel_pch_thermal: Add Cannon Lake Low Power PCH support
thermal: mediatek: Add tsensor support for V2 thermal system
thermal: mediatek: Prepare to add support for other platforms
thermal: Update power allocator and devfreq cooling to SPDX licensing
MAINTAINERS: update entry to thermal governors file name prefixing
thermal: core: Add thermal zone enable/disable notification
thermal: qcom: tsens-v0_1: Add support for MSM8939
dt-bindings: tsens: qcom: Document MSM8939 compatible
thermal: core: Fix thermal zone lookup by ID
thermal: int340x: processor_thermal: fix: update Jasper Lake PCI id
thermal: imx8mm: Support module autoloading
thermal: ti-soc-thermal: Fix reversed condition in ti_thermal_expose_sensor()
MAINTAINERS: Add maintenance information for IPA
thermal: rcar_gen3_thermal: Do not shadow thcode variable
dt-bindings: thermal: Get rid of thermal.txt and replace references
thermal: core: Move initialization after core initcall
thermal: netlink: Improve the initcall ordering
net: genetlink: Move initialization to core_initcall
thermal: rcar_gen3_thermal: Add r8a774e1 support
thermal/drivers/clock_cooling: Remove clock_cooling code
...
static priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low' priority level,
plus sched_set_normal() to set the policy back to non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in a separate
tree.
When merging to the latest upstream tree there's a conflict in drivers/spi/spi.c,
which can be resolved via:
sched_set_fifo(ctlr->kworker_task);
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/7JH
-----END PGP SIGNATURE-----
Merge tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched/fifo updates from Ingo Molnar:
"This adds the sched_set_fifo*() encapsulation APIs to remove static
priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low'
priority level, plus sched_set_normal() to set the policy back to
non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in
a separate tree"
* tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched,tracing: Convert to sched_set_fifo()
sched: Remove sched_set_*() return value
sched: Remove sched_setscheduler*() EXPORTs
sched,psi: Convert to sched_set_fifo_low()
sched,rcutorture: Convert to sched_set_fifo_low()
sched,rcuperf: Convert to sched_set_fifo_low()
sched,locktorture: Convert to sched_set_fifo()
sched,irq: Convert to sched_set_fifo()
sched,watchdog: Convert to sched_set_fifo()
sched,serial: Convert to sched_set_fifo()
sched,powerclamp: Convert to sched_set_fifo()
sched,ion: Convert to sched_set_normal()
sched,powercap: Convert to sched_set_fifo*()
sched,spi: Convert to sched_set_fifo*()
sched,mmc: Convert to sched_set_fifo*()
sched,ivtv: Convert to sched_set_fifo*()
sched,drm/scheduler: Convert to sched_set_fifo*()
sched,msm: Convert to sched_set_fifo*()
sched,psci: Convert to sched_set_fifo*()
sched,drbd: Convert to sched_set_fifo*()
...
* pm-em:
OPP: refactor dev_pm_opp_of_register_em() and update related drivers
Documentation: power: update Energy Model description
PM / EM: change name of em_pd_energy to em_cpu_energy
PM / EM: remove em_register_perf_domain
PM / EM: add support for other devices than CPUs in Energy Model
PM / EM: update callback structure and add device pointer
PM / EM: introduce em_dev_register_perf_domain function
PM / EM: change naming convention from 'capacity' to 'performance'
* pm-core:
mmc: jz4740: Use pm_ptr() macro
PM: Make *_DEV_PM_OPS macros use __maybe_unused
PM: core: introduce pm_ptr() macro
This patch adds full support for ver 2 thermal system (e.g., MT7622 SoC).
The new changes include reading calibration data, converting temperature
and hardware initialization which are specific for version 2 system.
Each platform decides which function to call according to its version.
Fixes: 3966be3c08 ("thermal: mediatek: add support for MT7622 SoC")
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1588238074-19338-3-git-send-email-henry.yen@mediatek.com
It is known that Mediatek owns two thermal systems, which only differ
in the way of reading calibration data and converting temperature.
MT8173, MT8183, MT2701 and MT2712 belongs to version 1 thermal
system, and MT7622 belongs to version 2.
In order to handle both systems, the suffix _V1 is appended to the
current code, and then the second patch will add _V2 functions with
the same purpose but different implementation.
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1588238074-19338-2-git-send-email-henry.yen@mediatek.com
Now the calls to enable/disable a thermal zone are centralized in a
call to a function, we can add in these the corresponding netlink
notifications.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200727231033.26512-1-daniel.lezcano@linaro.org
The TSENS integrated on MSM8939 is a v0_1 device with 10 sensors.
Different from its predecessor MSM8916, where 'calib_sel' bits sit in
separate qfprom word, MSM8939 has 'cailb' and 'calib_sel' bits mixed and
spread on discrete offsets. That's why all qfprom bits are read as one
go and later mapped to calibration data for MSM8939.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Konrad Dybcio <konradybcio@gmail.com> /* on Asus Z00T smartphone */
Acked-by: Konrad Dybcio <konradybcio@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629144926.665-3-shawn.guo@linaro.org
When a thermal zone is looked up by an ID and no zone is found matching
that ID, the thermal_zone_get_by_id() function will return a pointer to
the thermal zone list head which isn't actually a valid thermal zone.
This can lead to a subsequent crash because a valid pointer is returned
to the called, but dereferencing that pointer as struct thermal_zone is
not safe.
Fixes: 329b064fbd ("thermal: core: Get thermal zone by id")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200724170105.2705467-1-thierry.reding@gmail.com
Update PCI device id for Jasper Lake processor thermal device.
With this proc_thermal driver is getting loaded and processor
thermal functionality works on Jasper Lake system.
Fixes: f64a6583d3 ("thermal: int340x: processor_thermal: Add Jasper Lake support")
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1595577146-1221-1-git-send-email-sumeet.r.pawnikar@intel.com
This condition is reversed and will cause breakage.
Fixes: 7440f518da ("thermal/drivers/ti-soc-thermal: Avoid dereferencing ERR_PTR")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200616091949.GA11940@mwanda
The function rcar_gen3_thermal_calc_coefs() takes an argument called
'thcode' which shadows the static global 'thcode' variable. This is not
harmful but bad for readability and is harmful for planned changes to
the driver. The THCODE values should be read from hardware fuses if they
are available and only fallback to the global 'thcode' variable if they
are not fused.
Rename the global 'thcode' variable to 'thcodes' to avoid shadowing the
symbol in functions that take it as an argument.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200610003300.884258-1-niklas.soderlund+renesas@ragnatech.se
The generic netlink is initialized at subsys_initcall, so far after
the thermal init routine and the thermal generic netlink family
initialization.
On ŝome platforms, that leads to a memory corruption.
The fix was sent to netdev@ to move the genetlink framework
initialization at core_initcall.
Move the thermal core initialization to postcore level which is very
close to core level.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200717164217.18819-2-daniel.lezcano@linaro.org
The initcalls like to play joke. In our case, the thermal-netlink
initcall is called after the thermal-core initcall but this one sends
a notification before the former is initialized. No issue was spotted,
but it could lead to a memory corruption, so instead of relying on the
core_initcall for the thermal-netlink, let's initialize directly from
the thermal-core init routine, so we have full control of the init
ordering.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200717164217.18819-1-daniel.lezcano@linaro.org
The variable ret is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200706140747.489075-1-colin.king@canonical.com
When the network is not configured, the netlink is disabled on all
the system. The thermal framework assumed the netlink is always
opt-in.
Fix this by adding a Kconfig option for the netlink notification,
defaulting to yes and depending on CONFIG_NET.
As the change implies multiple stubs and in order to not pollute the
internal thermal header, the thermal_nelink.h has been added and
included in the thermal_core.h, so this one regain some kind of
clarity.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200707090159.1018-1-daniel.lezcano@linaro.org
kernel panic (Bartosz Szczepanek)
- Fix debug message level to prevent flooding on some platform (Alex
Hung)
- Fix invalid bank access by reverting "thermal: mediatek: fix
register index error" (Enric Balletbo i Serra)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl8QFhUACgkQqDIjiipP
6E99Uwf+O+MIwd4epoWG6L3SYYaOJZpkmdYJoWIXxLZu5jGiS0uf48utaXVJrTSQ
5VXCoqd2alxzAE2ZveqEV2Lp558+rT7cRmWd6ZH6UPVEC2j+1TzVfcSwJRm8jrNN
lbmt2785wcUsfRzuHqfCEIDW6HTjfcGj4d+a8CJ4K/58CdhaxOxGgDK5Wsmmy/jF
Fkco37wUVw0Ew9cAuc2OwB8hOjDMtMnBZ4xoPSaptIVEyCUurl+c1JOxFkubOM0x
a7DyBS8zKM4UVGo7jaUXwC/28TUFDZNJD8E7H4JOJfVSqK5l3HKfjqeVE44cS2SJ
u9RvLCyQkp/+CC75MfIEEpqgDLHZcA==
=0Xzx
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux into master
Pull thermal fixes from Daniel Lezcano:
- Fix invalid index array access on int340x_thermal leading to a kernel
panic (Bartosz Szczepanek)
- Fix debug message level to prevent flooding on some platform (Alex
Hung)
- Fix invalid bank access by reverting "thermal: mediatek: fix register
index error" (Enric Balletbo i Serra)
* tag 'thermal-v5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
Revert "thermal: mediatek: fix register index error"
thermal: int3403_thermal: Downgrade error message
thermal/int340x_thermal: Prevent page fault on .set_mode() op
Downgrade "Unsupported event" message from dev_err to dev_dbg to avoid
flooding with this message on some platforms.
Cc: stable@vger.kernel.org # v5.4+
Suggested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Alex Hung <alex.hung@canonical.com>
[ rzhang: fix typo in changelog ]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200615223957.183153-1-alex.hung@canonical.com
Starting from commit "thermal/int340x_thermal: Don't require IDSP to
exist", priv->current_uuid_index is initialized to -1. This value may
be passed to int3400_thermal_run_osc() from int3400_thermal_set_mode,
contributing to page fault when accessing int3400_thermal_uuids array
at index -1.
This commit adds a check on uuid value to int3400_thermal_run_osc.
Fixes: 8d485da0dd ("thermal/int340x_thermal: Don't require IDSP to exist")
Signed-off-by: Bartosz Szczepanek <bsz@semihalf.com>
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
[ rzhang: Add Fixes tag ]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200708134613.131555-1-bsz@semihalf.com
The generic netlink protocol is implemented but the different
notification functions are not yet connected to the core code.
These changes add the notification calls in the different
corresponding places.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200706105538.2159-4-daniel.lezcano@linaro.org
Initially the thermal framework had a very simple notification
mechanism to send generic netlink messages to the userspace.
The notification function was never called from anywhere and the
corresponding dead code was removed. It was probably a first attempt
to introduce the netlink notification.
At LPC2018, the presentation "Linux thermal: User kernel interface",
proposed to create the notifications to the userspace via a kfifo.
The advantage of the kfifo is the performance. It is usually used from
a 1:1 communication channel where a driver captures data and sends it
as fast as possible to a userspace process.
The drawback is that only one process uses the notification channel
exclusively, thus no other process is allowed to use the channel to
get temperature or notifications.
This patch defines a generic netlink API to discover the current
thermal setup and adds event notifications as well as temperature
sampling. As any genetlink protocol, it can evolve and the versioning
allows to keep the backward compatibility.
In order to prevent the user from getting flooded with data on a
single channel, there are two multicast channels, one for the
temperature sampling when the thermal zone is updated and another one
for the events, so the user can get the events only without the
thermal zone temperature sampling.
Also, a list of commands to discover the thermal setup is added and
can be extended when needed.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200706105538.2159-3-daniel.lezcano@linaro.org
The next patch will introduce the generic netlink protocol to handle
events, sampling and command from the thermal framework. In order to
deal with the thermal zone, it uses its unique identifier to
characterize it in the message. Passing an integer is more efficient
than passing an entire string.
This change provides a function returning back a thermal zone pointer
corresponding to the identifier passed as parameter.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200706105538.2159-2-daniel.lezcano@linaro.org
The cdev, tz and governor list, as well as their respective locks are
statically defined in the thermal_core.c file.
In order to give a sane access to these list, like browsing all the
thermal zones or all the cooling devices, let's define a set of
helpers where we pass a callback as a parameter to be called for each
thermal entity.
We keep the self-encapsulation and ensure the locks are correctly
taken when looking at the list.
Acked-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200706105538.2159-1-daniel.lezcano@linaro.org
set_mode() is only called when tzd's mode is about to change. Actual
setting is performed in thermal_core, in thermal_zone_device_set_mode().
The meaning of set_mode() callback is actually to notify the driver about
the mode being changed and giving the driver a chance to oppose such
change.
To better reflect the purpose of the method rename it to change_mode()
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-12-andrzej.p@collabora.com
Setting polling_delay is now done at thermal_core level (by not polling
DISABLED devices), so no need to repeat this code.
int340x: Checking for an impossible enum value is unnecessary.
acpi/thermal: It only prints debug messages.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-11-andrzej.p@collabora.com
Polling DISABLED devices is not desired, as all such "disabled" devices
are meant to be handled by userspace. This patch introduces and uses
should_stop_polling() to decide whether the device should be polled or not.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-10-andrzej.p@collabora.com
Some thermal zone devices never change their state, so they should be
always enabled.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-9-andrzej.p@collabora.com
Use thermal_zone_device_{en|dis}able() and thermal_zone_device_is_enabled().
Consequently, all set_mode() implementations in drivers:
- can stop modifying tzd's "mode" member,
- shall stop taking tzd's lock, as it is taken in the helpers
- shall stop calling thermal_zone_device_update() as it is called in the
helpers
- can assume they are called when the mode truly changes, so checks to
verify that can be dropped
Not providing set_mode() by a driver no longer prevents the core from
being able to set tzd's mode, so the relevant check in mode_store() is
removed.
Other comments:
- acpi/thermal.c: tz->thermal_zone->mode will be updated only after we
return from set_mode(), so use function parameter in thermal_set_mode()
instead, no need to call acpi_thermal_check() in set_mode()
- thermal/imx_thermal.c: regmap writes and mode assignment are done in
thermal_zone_device_{en|dis}able() and set_mode() callback
- thermal/intel/intel_quark_dts_thermal.c: soc_dts_{en|dis}able() are a
part of set_mode() callback, so they don't need to modify tzd->mode, and
don't need to fall back to the opposite mode if unsuccessful, as the return
value will be propagated to thermal_zone_device_{en|dis}able() and
ultimately tzd's member will not be changed in thermal_zone_device_set_mode().
- thermal/of-thermal.c: no need to set zone->mode to DISABLED in
of_parse_thermal_zones() as a tzd is kzalloc'ed so mode is DISABLED anyway
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-8-andrzej.p@collabora.com
Prepare for making the drivers not access tzd's private members.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[staticize thermal_zone_device_set_mode()]
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-7-andrzej.p@collabora.com
get_mode() is now redundant, as the state is stored in struct
thermal_zone_device.
Consequently the "mode" attribute in sysfs can always be visible, because
it is always possible to get the mode from struct tzd.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-6-andrzej.p@collabora.com
As description for DIV_ROUND_CLOSEST in file include/linux/kernel.h.
"Result is undefined for negative divisors if the dividend variable
type is unsigned and for negative dividends if the divisor variable
type is unsigned."
In current code, the FIXPT_DIV uses DIV_ROUND_CLOSEST but has not
checked sign of divisor before using. It makes undefined temperature
value in case the value is negative.
This patch fixes to satisfy DIV_ROUND_CLOSEST description
and fix bug too. Note that the variable name "reg" is not good
because it should be the same type as rcar_gen3_thermal_read().
However, it's better to rename the "reg" in a further patch as
cleanup.
Signed-off-by: Van Do <van.do.xw@renesas.com>
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
[shimoda: minor fixes, add Fixes tag]
Fixes: 564e73d283 ("thermal: rcar_gen3_thermal: Add R-Car Gen3 thermal driver")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Niklas Soderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Soderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1593085099-2057-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
The function cpu_power_to_freq is used to find a frequency and set the
cooling device to consume at most the power to be converted. For example,
if the power to be converted is 80mW, and the em table is as follow.
struct em_cap_state table[] = {
/* KHz mW */
{ 1008000, 36, 0 },
{ 1200000, 49, 0 },
{ 1296000, 59, 0 },
{ 1416000, 72, 0 },
{ 1512000, 86, 0 },
};
The target frequency should be 1416000KHz, not 1512000KHz.
Fixes: 349d39dc57 ("thermal: cpu_cooling: merge frequency and power tables")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200619090825.32747-1-finley.xiao@rock-chips.com
After merging tsens-common.c into tsens.c, we can now mark some
functions static so they don't need any prototype declarations. This
fixes the following issue reported by lkp.
>> drivers/thermal/qcom/tsens.c:385:13: warning: no previous prototype for 'tsens_critical_irq_thread' [-Wmissing-prototypes]
385 | irqreturn_t tsens_critical_irq_thread(int irq, void *data)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
>> drivers/thermal/qcom/tsens.c:455:13: warning: no previous prototype for 'tsens_irq_thread' [-Wmissing-prototypes]
455 | irqreturn_t tsens_irq_thread(int irq, void *data)
| ^~~~~~~~~~~~~~~~
>> drivers/thermal/qcom/tsens.c:523:5: warning: no previous prototype for 'tsens_set_trips' [-Wmissing-prototypes]
523 | int tsens_set_trips(void *_sensor, int low, int high)
| ^~~~~~~~~~~~~~~
>> drivers/thermal/qcom/tsens.c:560:5: warning: no previous prototype for 'tsens_enable_irq' [-Wmissing-prototypes]
560 | int tsens_enable_irq(struct tsens_priv *priv)
| ^~~~~~~~~~~~~~~~
>> drivers/thermal/qcom/tsens.c:573:6: warning: no previous prototype for 'tsens_disable_irq' [-Wmissing-prototypes]
573 | void tsens_disable_irq(struct tsens_priv *priv)
| ^~~~~~~~~~~~~~~~~
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/6757a26876b29922929abf64b1c11fa3b3033d03.1590579709.git.amit.kucheria@linaro.org
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Fixes: 554fdbaf19 ("thermal: sprd: Add Spreadtrum thermal driver support")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1590371941-25430-1-git-send-email-yangtiezhu@loongson.cn
MT8183_NUM_ZONES should be set to 1
because MT8183 doesn't have multiple banks.
Fixes: a4ffe6b52d ("thermal: mediatek: add support for MT8183")
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200323121537.22697-6-michael.kao@mediatek.com
The new Khadas VIM2 and VIM3 boards controls the cooling fan via the
on-board microcontroller.
This implements the FAN control as thermal devices and as cell of the Khadas
MCU MFD driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Energy Model uses concept of performance domain and capacity states in
order to calculate power used by CPUs. Change naming convention from
capacity to performance state would enable wider usage in future, e.g.
upcoming support for other devices other than CPUs.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Quentin Perret <qperret@google.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Because SCHED_FIFO is a broken scheduler model (see previous patches)
take away the priority field, the kernel can't possibly make an
informed decision.
Effectively no change.
Cc: rafael.j.wysocki@intel.com
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
- Thermal framework cleanups (self-encapsulation, pointless stubs,
private structures) (Daniel Lezcano)
- Use the PM QoS frequency changes for the devfreq cooling device (Matthias
Kaehlcke)
- Remove duplicate error messages from platform_get_irq() error handling
(Markus Elfring)
- Add support for the bandgap sensors (Keerthy)
- Statically initialize .get_mode/.set_mode ops (Andrzej Pietrasiewicz)
- Add Renesas R-Car maintainer entry (Niklas Söderlund)
- Fix error checking after calling ti_bandgap_get_sensor_data() for the TI SoC
thermal (Sudip Mukherjee)
- Add latency constraint for the idle injection, the DT binding and the change
the registering function (Daniel Lezcano)
- Convert the thermal framework binding to the Yaml schema (Amit Kucheria)
- Replace zero-length array with flexible-array on i.MX 8MM (Gustavo A. R. Silva)
- Thermal framework cleanups (alphabetic order for heads, replace module.h by
export.h, make file naming consistent) (Amit Kucheria)
- Merge tsens-common into the tsens driver (Amit Kucheria)
- Fix platform dependency for the Qoriq driver (Geert Uytterhoeven)
- Clean up the rcar_thermal_update_temp() function in the rcar thermal driver
(Niklas Söderlund)
- Fix the TMSAR register for the TMUv2 on the Qoriq platform (Yuantian Tang)
- Export GDDV, OEM vendor variables, and don't require IDSP for the int340x
thermal driver - trivial conflicts fixed (Matthew Garrett)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl7jra8ACgkQqDIjiipP
6E+ugAgApBF6FsHoonWIvoSrzBrrbU2oqhEJA42Mx+iY/UnXi01I79vZ/8WpZt7M
D1J01Kf0PUhRbywoKaoCX3Oh9ZO9PKq4N9ZC8yqdoD6GLl+rC9Wmr7Ui+c80klcv
M9rYhpPYfNXTFj0saSbbFWNNhP4TvhzGsNj8foYVQDKyhjbSmNE5ipZlbmP23jlr
O53SmJAwS5zxLOd8QA5nfSWP9FYYMuCR2AHj8BUCmxiAjXZLPNB/Hz2RRBr7q0MF
zRo/4HJ04mSQYp0kluP/EBhz9g2wM/htIPyWRveB/ByKEYt3UNKjB++PJmPbu5UG
dS3aXZhRfaPqpdsWrMB9fY7ll+oyfw==
=T+RI
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Add the hwmon support on the i.MX SC (Anson Huang)
- Thermal framework cleanups (self-encapsulation, pointless stubs,
private structures) (Daniel Lezcano)
- Use the PM QoS frequency changes for the devfreq cooling device
(Matthias Kaehlcke)
- Remove duplicate error messages from platform_get_irq() error
handling (Markus Elfring)
- Add support for the bandgap sensors (Keerthy)
- Statically initialize .get_mode/.set_mode ops (Andrzej Pietrasiewicz)
- Add Renesas R-Car maintainer entry (Niklas Söderlund)
- Fix error checking after calling ti_bandgap_get_sensor_data() for the
TI SoC thermal (Sudip Mukherjee)
- Add latency constraint for the idle injection, the DT binding and the
change the registering function (Daniel Lezcano)
- Convert the thermal framework binding to the Yaml schema (Amit
Kucheria)
- Replace zero-length array with flexible-array on i.MX 8MM (Gustavo A.
R. Silva)
- Thermal framework cleanups (alphabetic order for heads, replace
module.h by export.h, make file naming consistent) (Amit Kucheria)
- Merge tsens-common into the tsens driver (Amit Kucheria)
- Fix platform dependency for the Qoriq driver (Geert Uytterhoeven)
- Clean up the rcar_thermal_update_temp() function in the rcar thermal
driver (Niklas Söderlund)
- Fix the TMSAR register for the TMUv2 on the Qoriq platform (Yuantian
Tang)
- Export GDDV, OEM vendor variables, and don't require IDSP for the
int340x thermal driver - trivial conflicts fixed (Matthew Garrett)
* tag 'thermal-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (48 commits)
thermal/int340x_thermal: Don't require IDSP to exist
thermal/int340x_thermal: Export OEM vendor variables
thermal/int340x_thermal: Export GDDV
thermal: qoriq: Update the settings for TMUv2
thermal: rcar_thermal: Clean up rcar_thermal_update_temp()
thermal: qoriq: Add platform dependencies
drivers: thermal: tsens: Merge tsens-common.c into tsens.c
thermal/of: Rename of-thermal.c
thermal/governors: Prefix all source files with gov_
thermal/drivers/user_space: Sort headers alphabetically
thermal/drivers/of-thermal: Sort headers alphabetically
thermal/drivers/cpufreq_cooling: Replace module.h with export.h
thermal/drivers/cpufreq_cooling: Sort headers alphabetically
thermal/drivers/clock_cooling: Include export.h
thermal/drivers/clock_cooling: Sort headers alphabetically
thermal/drivers/thermal_hwmon: Include export.h
thermal/drivers/thermal_hwmon: Sort headers alphabetically
thermal/drivers/thermal_helpers: Include export.h
thermal/drivers/thermal_helpers: Sort headers alphabetically
thermal/core: Replace module.h with export.h
...
The IDSP method doesn't appear to exist on the most recent Intel platforms:
instead, the IDSP data is included in the GDDV blob. Since we probably
don't want to decompress and parse that in-kernel, just allow any UUID to
be written if IDSP is missing.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Tested-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
[ rzhang: fix checkpatch warning in changelog ]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200414020953.255364-3-matthewgarrett@google.com
The platform vendor may expose an array of OEM-specific values to be used
in determining DPTF policy. These are obtained via the ODVP method, and
then simply exposed in sysfs. In addition, they are updated when a
notification is received or when the DPTF policy is changed by userland.
Conflicts:
drivers/thermal/intel/int340x_thermal/int3400_thermal.c
Signed-off-by: Matthew Garrett <mjg59@google.com>
Tested-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200414020953.255364-2-matthewgarrett@google.com
Implementing DPTF properly requires making use of firmware-provided
information associated with the INT3400 device. Calling GDDV provides a
buffer of information which userland can then interpret to determine
appropriate DPTF policy.
Conflicts:
drivers/thermal/intel/int340x_thermal/int3400_thermal.c
Signed-off-by: Matthew Garrett <mjg59@google.com>
Tested-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200414020953.255364-1-matthewgarrett@google.com
For TMU v2, TMSAR registers need to be set properly to get the
accurate temperature values.
Also the temperature read needs to be converted to degree Celsius
since it is in degrees Kelvin.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200526060212.4118-1-andy.tang@nxp.com
Moving the ctemp variable out of the private data structure made it
possible to clean up rcar_thermal_update_temp(). Initialize the local
ctemp to the error code to return if the reading fails and just return
it at the end of the function.
It's OK to change the datatype of old, new and ctemp to int as all
values are ANDed with CTEMP (0x3f) before being stored. While at it
change the datatype of the loop variable 'i' to to unsigned int.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200514152505.1927634-1-niklas.soderlund+renesas@ragnatech.se
The QorIQ Thermal Monitoring Unit is only present on Freescale E500MC
and Layerscape SoCs, and on NXP i.MX8 SoCs. Add platform dependencies
to the QORIQ_THERMAL config symbol, to avoid asking the user about it
when configuring a kernel without support for any of the aforementioned
SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200507112955.23520-5-geert+renesas@glider.be
tsens-common.c has outlived its usefuless. It was created expecting lots
of custom routines per version of the TSENS IP. We haven't needed those,
there is now only data in the version-specific files.
Merge the code for tsens-common.c into tsens.c. As a result,
- Remove any unnecessary forward declarations in tsens.h.
- Add a Linaro copyright to tsens.c.
- Fixup the Makefile to remove tsens-common.c.
- Where it made sense, fix some 80-column alignments in the
tsens-common.c code being copied over.
There is no functional change with this patch.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/e30e2ba6fa5c007983afd4d7d4e0311c0b57917a.1588183879.git.amit.kucheria@linaro.org
The thermal framework can no longer be compiled as a module as of
commit 554b3529fe ("thermal/drivers/core: Remove the module Kconfig's
option"). Remove the MODULE_* tags.
Rui is mentioned in the copyright line at the top of the file and the
license is mentioned in the SPDX tags. So no loss of information.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/74339a09a55f8f3d86c4074fc2bf853a302d6186.1589199124.git.amit.kucheria@linaro.org
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200507192517.GA16557@embeddedor
Today, there is no user for the cpuidle cooling device. The targetted
platform is ARM and ARM64.
The cpuidle and the cpufreq cooling device are based on the device tree.
As the cpuidle cooling device can have its own configuration depending
on the platform and the available idle states. The DT node description
will give the optional properties to set the cooling device up.
Do no longer rely on the CPU node which is prone to error and will
lead to a confusion in the DT because the cpufreq cooling device is
also using it. Let initialize the cpuidle cooling device with the DT
binding.
This was tested on:
- hikey960
- hikey6220
- rock960
- db845c
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200429103644.5492-3-daniel.lezcano@linaro.org
i.MX8 SoCs DTS file needs system control macro definitions, so move them
into dt-binding headfile, then include/linux/firmware/imx/types.h can be
removed and those drivers using it should be changed accordingly.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On error the function ti_bandgap_get_sensor_data() returns the error
code in ERR_PTR() but we only checked if the return value is NULL or
not. And, so we can dereference an error code inside ERR_PTR.
While at it, convert a check to IS_ERR_OR_NULL.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200424161944.6044-1-sudipm.mukherjee@gmail.com
int3400_thermal_ops is used inside int3400_thermal_probe() only after
the assignments, which can just as well be made statically at struct's
initizer.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200414180105.20042-2-andrzej.p@collabora.com
Add VTM thermal support. In the Voltage Thermal Management
Module(VTM), K3 AM654 supplies a voltage reference and a temperature
sensor feature that are gathered in the band gap voltage and
temperature sensor (VBGAPTS) module. The band gap provides current and
voltage reference for its internal circuits and other analog IP
blocks. The analog-to-digital converter (ADC) produces an output value
that is proportional to the silicon temperature.
Currently reading temperatures only is supported. There are no
active/passive cooling agent supported.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200407055116.16082-3-j-keerthy@ti.com
The function “platform_get_irq” can log an error already.
Thus omit redundant messages for the exception handling in the
calling functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/05f49ae7-5cc7-d6a0-fc3d-abaf2a0b373c@web.de
The function is not used any place other than the thermal
directory. It does not make sense to export its definition in the
global header as there is no use of it.
Move the definition to the internal header and allow better
self-encapsulation.
Take the opportunity to add the parameter names to make checkpatch
happy and remove the pointless stubs.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200402142747.8307-6-daniel.lezcano@linaro.org
The function is not used any place other than the thermal
directory. It does not make sense to export its definition in the
global header as there is no use of it.
Move the definition to the internal header and allow better
self-encapsulation.
Take the opportunity to add the parameter names to make checkpatch
happy and remove the pointless stubs.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200402142747.8307-5-daniel.lezcano@linaro.org
The struct thermal_trip is only used by the thermal internals, it is
pointless to export the definition in the global header.
Move the structure to the thermal_core.h internal header.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200402142747.8307-4-daniel.lezcano@linaro.org
The exported IPA functions are used by the IPA. It is pointless to
declare the functions in the thermal.h file.
For better self-encapsulation and less impact for the compilation if a
change is made on it. Move the code in the thermal core internal
header file.
As the users depends on THERMAL then it is pointless to have the stub,
remove them.
Take also the opportunity to fix checkpatch warnings/errors when
moving the code around.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200402142747.8307-3-daniel.lezcano@linaro.org
The structure belongs to the thermal core internals but it is exported
in the include/linux/thermal.h
For better self-encapsulation and less impact for the compilation if a
change is made on it. Move the structure in the thermal core internal
header file.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200402142747.8307-2-daniel.lezcano@linaro.org
The default governor set at compilation time is a thermal internal
business, no need to export to the global thermal header.
Move the config options to the internal header.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200402142747.8307-1-daniel.lezcano@linaro.org
Now that devfreq supports limiting the frequency range of a device
through PM QoS make use of it instead of disabling OPPs that should
not be used.
The switch from disabling OPPs to PM QoS introduces a subtle behavioral
change in case of conflicting requests (min > max): PM QoS gives
precedence to the MIN_FREQUENCY request, while higher OPPs disabled
with dev_pm_opp_disable() would override MIN_FREQUENCY.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200318114548.19916-4-lukasz.luba@arm.com
The last temperature and the current temperature are show via a
dev_debug. The line before, those temperature are also traced.
It is pointless to duplicate the traces for the temperatures,
remove the dev_dbg traces.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200331165449.30355-2-daniel.lezcano@linaro.org
The function thermal_zone_set_trips() is used by the thermal core code
in order to update the next trip points, there are no other users.
Move the function definition in the thermal_core.h, remove the
EXPORT_SYMBOL_GPL and document the function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200331165449.30355-1-daniel.lezcano@linaro.org
- Add interrupt support on the rcar sensor (Niklas Söderlund)
- Add a new Spreadtrum thermal driver (Baolin Wang)
- Add thermal binding for the fsl scu board, a new API to retrieve the
sensor id bound to the thermal zone and i.MX system controller
sensor (Anson Huang))
- Remove warning log when a deferred probe is requested on Exynos
(Marek Szyprowski)
- Add the thermal monitoring unit support for imx8mm with its DT
bindings (Anson Huang)
- Rephrase the Kconfig text for clarity (Linus Walleij)
- Use the gpio descriptor for the ti-soc-thermal (Linus Walleij)
- Align msg structure to 4 bytes for i.MX SC, fix the Kconfig
dependency, add the __may_be unused annotation for PM functions and
the COMPILE_TEST option for imx8mm (Anson Huang)
- Fix a dependency on regmap in Kconfig for qoriq (Yuantian Tang)
- Add DT binding and support for the rcar gen3 r8a77961 and improve
the error path on the rcar init function (Niklas Söderlund)
- Cleanup and improvements for the tsens Qcom sensor (Amit Kucheria)
- Improve code by removing lock and caching values in the rcar thermal
sensor (Niklas Söderlund)
- Cleanup in the qoriq drivers and add a call to
imx_thermal_unregister_legacy_cooling in the removal function (Anson
Huang)
- Remove redundant 'maxItems' in tsens and sprd DT bindings (Rob Herring)
- Change the thermal DT bindings by making the cooling-maps optional
(Yuantian Tang)
- Add Tiger Lake support (Sumeet Pawnikar)
- Use scnprintf() for avoiding potential buffer overflow (Takashi Iwai)
- Make pkg_temp_lock a raw_spinlock_t(Clark Williams)
- Fix incorrect data types by changing them to signed on i.MX SC (Anson Huang)
- Replace zero-length array with flexible-array member (Gustavo A. R. Silva)
- Add support for i.MX8MP in the driver and in the DT bindings (Anson Huang)
- Fix return value of the cpufreq_set_cur_state() function (Willy Wolff)
- Remove abusing and scary WARN_ON in the cpufreq cooling device
(Daniel Lezcano)
- Fix build warning of incorrect argument type reported by sparse on
imx8mm (Anson Huang)
- Fix stub for the devfreq cooling device (Martin Blumenstingl)
- Fix cpu idle cooling documentation (Sergey Vidishev)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl6MXkEACgkQqDIjiipP
6E+BIggAh52YBU8D8GthsvCPTgka95+wAIaZtx4Y7UnhvshHhM2w+m97TQOXK373
95mwO9mwQuAoksSmLo7pBQYJ7HItQ26Yoq9akpOL6EiT+BEWiqoHJgl+afVVtoKa
n67d3Pa6coup1+PQNIA8kpTIOmUQTP8THtwpZ3HlChWsg22NTd0QUGpGJ1TtBD/q
KqMdQjxahFJ4RTYsnECWBkw3EMkczMNMgdrXEvm4rMkcaJzv9g2ZPqerOShK/RzP
8sejWczt6jaRwu4hLpd/lLikTSHZoXMFJ8ylAiQXFELCPAQIrMS/ae+dTGJ4qP7x
hkjsewPbeA1Z+al/IBVHiCtOzKkICQ==
=XDYl
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Convert tsens configuration DT binding to yaml (Rajeshwari)
- Add interrupt support on the rcar sensor (Niklas Söderlund)
- Add a new Spreadtrum thermal driver (Baolin Wang)
- Add thermal binding for the fsl scu board, a new API to retrieve the
sensor id bound to the thermal zone and i.MX system controller sensor
(Anson Huang))
- Remove warning log when a deferred probe is requested on Exynos
(Marek Szyprowski)
- Add the thermal monitoring unit support for imx8mm with its DT
bindings (Anson Huang)
- Rephrase the Kconfig text for clarity (Linus Walleij)
- Use the gpio descriptor for the ti-soc-thermal (Linus Walleij)
- Align msg structure to 4 bytes for i.MX SC, fix the Kconfig
dependency, add the __may_be unused annotation for PM functions and
the COMPILE_TEST option for imx8mm (Anson Huang)
- Fix a dependency on regmap in Kconfig for qoriq (Yuantian Tang)
- Add DT binding and support for the rcar gen3 r8a77961 and improve the
error path on the rcar init function (Niklas Söderlund)
- Cleanup and improvements for the tsens Qcom sensor (Amit Kucheria)
- Improve code by removing lock and caching values in the rcar thermal
sensor (Niklas Söderlund)
- Cleanup in the qoriq drivers and add a call to
imx_thermal_unregister_legacy_cooling in the removal function (Anson
Huang)
- Remove redundant 'maxItems' in tsens and sprd DT bindings (Rob
Herring)
- Change the thermal DT bindings by making the cooling-maps optional
(Yuantian Tang)
- Add Tiger Lake support (Sumeet Pawnikar)
- Use scnprintf() for avoiding potential buffer overflow (Takashi Iwai)
- Make pkg_temp_lock a raw_spinlock_t(Clark Williams)
- Fix incorrect data types by changing them to signed on i.MX SC (Anson
Huang)
- Replace zero-length array with flexible-array member (Gustavo A. R.
Silva)
- Add support for i.MX8MP in the driver and in the DT bindings (Anson
Huang)
- Fix return value of the cpufreq_set_cur_state() function (Willy
Wolff)
- Remove abusing and scary WARN_ON in the cpufreq cooling device
(Daniel Lezcano)
- Fix build warning of incorrect argument type reported by sparse on
imx8mm (Anson Huang)
- Fix stub for the devfreq cooling device (Martin Blumenstingl)
- Fix cpu idle cooling documentation (Sergey Vidishev)
* tag 'thermal-v5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (52 commits)
Documentation: cpu-idle-cooling: Fix diagram for 33% duty cycle
thermal: devfreq_cooling: inline all stubs for CONFIG_DEVFREQ_THERMAL=n
thermal: imx8mm: Fix build warning of incorrect argument type
thermal/drivers/cpufreq_cooling: Remove abusing WARN_ON
thermal/drivers/cpufreq_cooling: Fix return of cpufreq_set_cur_state
thermal: imx8mm: Add i.MX8MP support
dt-bindings: thermal: imx8mm-thermal: Add support for i.MX8MP
thermal: qcom: tsens.h: Replace zero-length array with flexible-array member
thermal: imx_sc_thermal: Fix incorrect data type
thermal: int340x_thermal: Use scnprintf() for avoiding potential buffer overflow
thermal: int340x: processor_thermal: Add Tiger Lake support
thermal/x86_pkg_temp: Make pkg_temp_lock a raw_spinlock_t
dt-bindings: thermal: make cooling-maps property optional
dt-bindings: thermal: qcom-tsens: Remove redundant 'maxItems'
dt-bindings: thermal: sprd: Remove redundant 'maxItems'
thermal: imx: Calling imx_thermal_unregister_legacy_cooling() in .remove
thermal: qoriq: Sort includes alphabetically
thermal: qoriq: Use devm_add_action_or_reset() to handle all cleanups
thermal: rcar_thermal: Remove lock in rcar_thermal_get_current_temp()
thermal: rcar_thermal: Do not store ctemp in rcar_thermal_priv
...
- Update the ACPICA code in the kernel to upstream revision 20200326
including:
* Fix for a typo in a comment field (Bob Moore).
* acpiExec namespace init file fixes (Bob Moore).
* Addition of NHLT to the known tables list (Cezary Rojewski).
* Conversion of PlatformCommChannel ASL keyword to PCC (Erik
Kaneda).
* acpiexec cleanup (Erik Kaneda).
* WSMT-related typo fix (Erik Kaneda).
* sprintf() utility function fix (John Levon).
* IVRS IVHD type 11h parsing implementation (Michał Żygowski).
* IVRS IVHD type 10h reserved field name fix (Michał Żygowski).
- Fix ACPI-related CPU hotplug deadlock on x86 (Qian Cai).
- Fix Intel Tiger Lake ACPI device IDs in several places (Gayatri
Kammela).
- Add ACPI backlight blacklist entry for Acer Aspire 5783z (Hans
de Goede).
- Fix documentation of the "acpi_backlight" kernel command line
switch (Randy Dunlap).
- Clean up the acpi_get_psd_map() CPPC library routine (Liguang
Zhang).
-----BEGIN PGP SIGNATURE-----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=b3Dp
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Additional ACPI updates.
These update the ACPICA code in the kernel to the 20200326 upstream
revision, fix an ACPI-related CPU hotplug deadlock on x86, update
Intel Tiger Lake device IDs in some places, add a new ACPI backlight
blacklist entry, update the "acpi_backlight" kernel command line
switch documentation and clean up a CPPC library routine.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20200326
including:
* Fix for a typo in a comment field (Bob Moore)
* acpiExec namespace init file fixes (Bob Moore)
* Addition of NHLT to the known tables list (Cezary Rojewski)
* Conversion of PlatformCommChannel ASL keyword to PCC (Erik
Kaneda)
* acpiexec cleanup (Erik Kaneda)
* WSMT-related typo fix (Erik Kaneda)
* sprintf() utility function fix (John Levon)
* IVRS IVHD type 11h parsing implementation (Michał Żygowski)
* IVRS IVHD type 10h reserved field name fix (Michał Żygowski)
- Fix ACPI-related CPU hotplug deadlock on x86 (Qian Cai)
- Fix Intel Tiger Lake ACPI device IDs in several places (Gayatri
Kammela)
- Add ACPI backlight blacklist entry for Acer Aspire 5783z (Hans de
Goede)
- Fix documentation of the "acpi_backlight" kernel command line
switch (Randy Dunlap)
- Clean up the acpi_get_psd_map() CPPC library routine (Liguang
Zhang)"
* tag 'acpi-5.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
x86: ACPI: fix CPU hotplug deadlock
thermal: int340x_thermal: fix: Update Tiger Lake ACPI device IDs
platform/x86: intel-hid: fix: Update Tiger Lake ACPI device ID
ACPI: Update Tiger Lake ACPI device IDs
ACPI: video: Use native backlight on Acer Aspire 5783z
ACPI: video: Docs update for "acpi_backlight" kernel parameter options
ACPICA: Update version 20200326
ACPICA: Fixes for acpiExec namespace init file
ACPICA: Add NHLT table signature
ACPICA: WSMT: Fix typo, no functional change
ACPICA: utilities: fix sprintf()
ACPICA: acpiexec: remove redeclaration of acpi_gbl_db_opt_no_region_support
ACPICA: Change PlatformCommChannel ASL keyword to PCC
ACPICA: Fix IVRS IVHD type 10h reserved field name
ACPICA: Implement IVRS IVHD type 11h parsing
ACPICA: Fix a typo in a comment field
ACPI: CPPC: clean up acpi_get_psd_map()
Tiger Lake's new unique ACPI device IDs for Intel thermal driver are not
valid because of missing 'C' in the IDs. Fix the IDs by updating them.
After the update, the new IDs should now look like
INT1040 --> INTC1040
INT1043 --> INTC1043
Fixes: 9b1b5535df ("thermal: int340x_thermal: Add Tiger Lake ACPI device IDs")
Cc: 5.6+ <stable@vger.kernel.org> # 5.6+
Suggested-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle are:
- Various NUMA scheduling updates: harmonize the load-balancer and
NUMA placement logic to not work against each other. The intended
result is better locality, better utilization and fewer migrations.
- Introduce Thermal Pressure tracking and optimizations, to improve
task placement on thermally overloaded systems.
- Implement frequency invariant scheduler accounting on (some) x86
CPUs. This is done by observing and sampling the 'recent' CPU
frequency average at ~tick boundaries. The CPU provides this data
via the APERF/MPERF MSRs. This hopefully makes our capacity
estimates more precise and keeps tasks on the same CPU better even
if it might seem overloaded at a lower momentary frequency. (As
usual, turbo mode is a complication that we resolve by observing
the maximum frequency and renormalizing to it.)
- Add asymmetric CPU capacity wakeup scan to improve capacity
utilization on asymmetric topologies. (big.LITTLE systems)
- PSI fixes and optimizations.
- RT scheduling capacity awareness fixes & improvements.
- Optimize the CONFIG_RT_GROUP_SCHED constraints code.
- Misc fixes, cleanups and optimizations - see the changelog for
details"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (62 commits)
threads: Update PID limit comment according to futex UAPI change
sched/fair: Fix condition of avg_load calculation
sched/rt: cpupri_find: Trigger a full search as fallback
kthread: Do not preempt current task if it is going to call schedule()
sched/fair: Improve spreading of utilization
sched: Avoid scale real weight down to zero
psi: Move PF_MEMSTALL out of task->flags
MAINTAINERS: Add maintenance information for psi
psi: Optimize switching tasks inside shared cgroups
psi: Fix cpu.pressure for cpu.max and competing cgroups
sched/core: Distribute tasks within affinity masks
sched/fair: Fix enqueue_task_fair warning
thermal/cpu-cooling, sched/core: Move the arch_set_thermal_pressure() API to generic scheduler code
sched/rt: Remove unnecessary push for unfit tasks
sched/rt: Allow pulling unfitting task
sched/rt: Optimize cpupri_find() on non-heterogenous systems
sched/rt: Re-instate old behavior in select_task_rq_rt()
sched/rt: cpupri_find: Implement fallback mechanism for !fit case
sched/fair: Fix reordering of enqueue/dequeue_task_fair()
sched/fair: Fix runnable_avg for throttled cfs
...
Pull perf updates from Ingo Molnar:
"The main changes in this cycle were:
Kernel side changes:
- A couple of x86/cpu cleanups and changes were grandfathered in due
to patch dependencies. These clean up the set of CPU model/family
matching macros with a consistent namespace and C99 initializer
style.
- A bunch of updates to various low level PMU drivers:
* AMD Family 19h L3 uncore PMU
* Intel Tiger Lake uncore support
* misc fixes to LBR TOS sampling
- optprobe fixes
- perf/cgroup: optimize cgroup event sched-in processing
- misc cleanups and fixes
Tooling side changes are to:
- perf {annotate,expr,record,report,stat,test}
- perl scripting
- libapi, libperf and libtraceevent
- vendor events on Intel and S390, ARM cs-etm
- Intel PT updates
- Documentation changes and updates to core facilities
- misc cleanups, fixes and other enhancements"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (89 commits)
cpufreq/intel_pstate: Fix wrong macro conversion
x86/cpu: Cleanup the now unused CPU match macros
hwrng: via_rng: Convert to new X86 CPU match macros
crypto: Convert to new CPU match macros
ASoC: Intel: Convert to new X86 CPU match macros
powercap/intel_rapl: Convert to new X86 CPU match macros
PCI: intel-mid: Convert to new X86 CPU match macros
mmc: sdhci-acpi: Convert to new X86 CPU match macros
intel_idle: Convert to new X86 CPU match macros
extcon: axp288: Convert to new X86 CPU match macros
thermal: Convert to new X86 CPU match macros
hwmon: Convert to new X86 CPU match macros
platform/x86: Convert to new CPU match macros
EDAC: Convert to new X86 CPU match macros
cpufreq: Convert to new X86 CPU match macros
ACPI: Convert to new X86 CPU match macros
x86/platform: Convert to new CPU match macros
x86/kernel: Convert to new CPU match macros
x86/kvm: Convert to new CPU match macros
x86/perf/events: Convert to new CPU match macros
...
The pkg_temp_lock spinlock is acquired in the thermal vector handler which
is truly atomic context even on PREEMPT_RT kernels.
The critical sections are tiny, so change it to a raw spinlock.
Signed-off-by: Clark Williams <williams@redhat.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20191008110021.2j44ayunal7fkb7i@linutronix.de
The new macro set has a consistent namespace and uses C99 initializers
instead of the grufty C89 ones.
Get rid the of the local QUARK defines and use the proper ones.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lkml.kernel.org/r/20200320131509.967017771@linutronix.de
The WARN_ON macros are used at the entry functions state2power() and
set_cur_state().
state2power() is called with the max_state retrieved from
get_max_state which returns cpufreq_cdev->max_level, then it check if
max_state is > cpufreq_cdev->max_level. The test does not really makes
sense but let's assume we want to make sure to catch an error if the
code evolves. However the WARN_ON is overkill.
set_cur_state() is also called from userspace if we write to the
sysfs. It is easy to see a stack dumped by just writing to sysfs
/sys/class/thermal/cooling_device0/cur_state a value greater than
"max_level". A bit scary. Returing -EINVAL is enough.
Remove these WARN_ON.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20200321193107.21590-1-daniel.lezcano@linaro.org
When setting the cooling device current state from userspace via sysfs,
the operation fails by returning an -EINVAL.
It appears the recent changes with the per-policy frequency QoS
introduced a regression as reported by:
https://lkml.org/lkml/2020/3/20/599
The function freq_qos_update_request returns 0 or 1 describing update
effectiveness, and a negative error code on failure. However,
cpufreq_set_cur_state returns 0 on success or an error code otherwise.
Consider the QoS update as successful if the function does not return
an error.
Fixes: 3000ce3c52 ("cpufreq: Use per-policy frequency QoS")
Signed-off-by: Willy Wolff <willy.mh.wolff.ml@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200321092740.7vvwfxsebcrznydh@macmini.local
i.MX8MP shares same TMU with i.MX8MM, the only difference is i.MX8MP
has two thermal sensors while i.MX8MM ONLY has one, add multiple sensors
support for i.MX8MM TMU driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1584674791-9717-2-git-send-email-Anson.Huang@nxp.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200319184838.GA25767@embeddedor.com
The temperature value passed from SCU could be negative value,
the data type should be signed instead of unsigned.
Fixes: e20db70dba ("thermal: imx_sc: add i.MX system controller thermal support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1584606380-9972-1-git-send-email-Anson.Huang@nxp.com
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200311092718.24052-1-tiwai@suse.de
In order to avoid future header hell, remove the inclusion of
proc_fs.h from acpi_bus.h. All it needs is a forward declaration of a
struct.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lkml.kernel.org/r/20200321113241.246190285@linutronix.de
The spinlock pkg_temp_lock has the potential of being taken in atomic
context because it can be acquired from the thermal IRQ vector.
It's static and limited scope so go ahead and make it a raw spinlock.
Signed-off-by: Clark Williams <williams@redhat.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191008110021.2j44ayunal7fkb7i@linutronix.de
imx_thermal_unregister_legacy_cooling() should be used for handling
legacy cpufreq cooling cleanups in .remove callback instead of
calling cpufreq_cooling_unregister() and cpufreq_cpu_put() directly,
especially for !CONFIG_CPU_FREQ scenario, no operation needed for
handling legacy cpufreq cooling cleanups at all.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1584088094-24857-1-git-send-email-Anson.Huang@nxp.com
Sort includes alphabetically for consistency, and take this chance
to remove unused include of of_address.h.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1583903252-2058-2-git-send-email-Anson.Huang@nxp.com
Use devm_add_action_or_reset() to handle all cleanups of failure in
.probe and .remove, then .remove callback can be dropped.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1583903252-2058-1-git-send-email-Anson.Huang@nxp.com
With the ctemp value returned instead of cached in the private data
structure their is no need to take the lock when translating ctemp into
a temperature.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200310170029.1648996-4-niklas.soderlund+renesas@ragnatech.se
There is no need to cache the ctemp value in the private data structure
as it's always prefetched before it's used. Remove it from the structure
and have rcar_thermal_update_temp return the value instead of storing
it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200310170029.1648996-3-niklas.soderlund+renesas@ragnatech.se
Since commit a1ade56538 ("thermal: rcar: check every
rcar_thermal_update_temp() return value") the temperature is always read
in rcar_thermal_get_current_temp() so comparing it before and after
enabling interrupts have little effect. Remove the check and always
update the thermal zone when we get an interrupt that the temperature
have changed.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200310170029.1648996-2-niklas.soderlund+renesas@ragnatech.se
IRQF_TRIGGER_HIGH is already specified through devicetree interrupts
property. Remove it from code.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/8ac92e45b65fe411f4aaf70dcde4e7e7c3169b2d.1584015867.git.amit.kucheria@linaro.org
TSENS IP v2.3 onwards adds support for a watchdog to detect if the TSENS
HW FSM is stuck. Add support to detect and restart the FSM in the
driver. The watchdog is configured by the bootloader, we just enable the
watchdog bark as a debug feature in the kernel.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/a314747664a065db592ad77da7beae68128a5b6e.1584015867.git.amit.kucheria@linaro.org
TSENS IP v2.x adds critical threshold interrupt support for each sensor
in addition to the upper/lower threshold interrupt. Add support in the
driver.
While the critical interrupts themselves aren't currently used by Linux,
the HW line is also used by the TSENS watchdog. So this patch acts as
infrastructure to enable watchdog functionality for the TSENS IP.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/51b22461d4b5f85a817274568459db4579fd4298.1584015867.git.amit.kucheria@linaro.org
We don't currently call put_device in case of successfully initialising
the device. So we hold the reference and keep the device pinned forever.
Allow control to fall through so we can use same code for success and
error paths to put_device.
As a part of this fixup, change devm_ioremap_resource to act on the same
device pointer as that used to allocate regmap memory. That ensures that
we are free to release op->dev after examining its resources.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/d3996667e9f976bb30e97e301585cb1023be422e.1584015867.git.amit.kucheria@linaro.org
We already dereference the sensor and save it into a variable. Use the
variable directly to make the code easier to read.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/5dc4356edfb8dffa377fb561359bf41a6f1fdf17.1584015867.git.amit.kucheria@linaro.org
All the sensor data is initialised at init time. Lock it down by passing
it to functions as a constant.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/740f9254484c08d65869df578628eb523c0049ff.1584015867.git.amit.kucheria@linaro.org
struct tsens_features is currently initialized as part of platform data
at compile-time and not modifiable. We now have some usecases in feature
detection across IP versions where it is more flexible to update the
features after probing registers.
Remove const qualifier from tsens_features and the encapsulating
tsens_plat_data.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/2919a72220470366ae11e0bb5330a4ea39838f71.1584015867.git.amit.kucheria@linaro.org
If the common register memory resource is not available the driver needs
to fail gracefully to disable PM. Instead of returning the error
directly store it in ret and use the already existing error path.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200310114709.1483860-1-niklas.soderlund+renesas@ragnatech.se
Add support for the Thermal Sensor/Chip Internal Voltage Monitor in the
R-Car M3-W+ (R8A77961) SoC.
According to the R-Car Gen3 Hardware Manual Errata for Revision 2.00 of
Jan 31, 2020, the thermal parameters for R-Car M3-W+ are the same as for
R-Car M3-W.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200306105503.24267-3-geert+renesas@glider.be
Qoriq thermal driver is used by both PowerPC and ARM architecture.
When built for PowerPC architecture, it reports error:
undefined reference to `.__devm_regmap_init_mmio_clk'
To fix it, select config REGMAP_MMIO.
Fixes: 4316237bd6 (thermal: qoriq: Convert driver to use regmap API)
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200303084641.35687-1-andy.tang@nxp.com
i.MX SCU thermal driver depends on IMX_SCU which does NOT have
COMPILE_TEST enabled, so need to remove COMPILE_TEST for i.MX
SCU thermal as well.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1583222684-10229-2-git-send-email-Anson.Huang@nxp.com
Use __maybe_unused for power management related functions instead
of #if CONFIG_PM_SLEEP to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1583139266-23615-1-git-send-email-Anson.Huang@nxp.com
The i.MX SCU API strongly assumes that messages are composed out
of 4-bytes words but some of our message structs have odd sizeofs,
use __packed __aligned(4) to avoid potential oopses.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1583117485-30922-1-git-send-email-Anson.Huang@nxp.com
This switches the TI SoC thermal driver to use GPIO
descriptors instead of retrieveing a GPIO number from the
device tree and requesting the GPIO separately.
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200229210532.173430-1-linus.walleij@linaro.org
The thermal subsystem may have relied on sysfs in 2008 when it
was introduced, but these days the thermal zones will more often
than not come from the hardware descriptions and not from sysfs.
Drop the "Generic" phrases as well: there are no non-generic
drivers that I know of, the thermal framework is by definition
generic.
Reword a bit and fix some grammar.
[ Daniel Lezcano ] : fixed Randy's comment s/offers/offer/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200229204527.143796-1-linus.walleij@linaro.org
i.MX8MM has a thermal monitoring unit(TMU) inside, it ONLY has one
sensor for CPU, add support for reading immediate temperature of
this sensor.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1582947862-11073-2-git-send-email-Anson.Huang@nxp.com
Don't confuse user with meaningless warning about the failure of
registering sensors in case of deferred probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200228092331.21548-1-m.szyprowski@samsung.com
i.MX8QXP is an ARMv8 SoC which has a Cortex-M4 system controller
inside, the system controller is in charge of controlling power,
clock and thermal sensors etc..
This patch adds i.MX system controller thermal driver support,
Linux kernel has to communicate with system controller via MU
(message unit) IPC to get each thermal sensor's temperature,
it supports multiple sensors which are passed from device tree,
please see the binding doc for details.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1582330132-13461-3-git-send-email-Anson.Huang@nxp.com
This patch adds new API thermal_zone_of_get_sensor_id() to
provide the feature of getting sensor ID from DT thermal
zone's node. It's useful for thermal driver to register the
specific thermal zone devices from DT in a common way.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1582330132-13461-2-git-send-email-Anson.Huang@nxp.com
This patch adds the support for Spreadtrum thermal sensor controller,
which can support maximum 8 sensors.
Signed-off-by: Freeman Liu <freeman.liu@unisoc.com>
Co-developed-with: Baolin Wang <baolin.wang@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/ebeb2839cff4d4027b37e787427c5af0e11880c8.1582013101.git.baolin.wang7@gmail.com
The desired behavior of the driver is to generate an interrupt and call
thermal_zone_device_update() as soon as the temperature have changed
more then one degree.
When the set_trips operation was implemented it was believed that the
trip window set by the framework would move around the current
temperature and the hysteresis value described in devicetree. The
behavior of the framework is however to set a window based on the trip
points described in devicetree.
Remove the set_trips operation which was not used correctly and update
the temperatures that triggers interrupts directly from the interrupt
handler.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200212224917.737314-1-niklas.soderlund+renesas@ragnatech.se
When devm_add_action() was turned into devm_add_action_or_reset() the
curly brackets for the error case where kept but are not needed, remove
them to match the style of the driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200212224732.736785-1-niklas.soderlund+renesas@ragnatech.se
Thermal governors can request for a CPU's maximum supported frequency to
be capped in case of an overheat event. This in turn means that the
maximum capacity available for tasks to run on the particular CPU is
reduced. Delta between the original maximum capacity and capped maximum
capacity is known as thermal pressure. Enable cpufreq cooling device to
update the thermal pressure in event of a capped maximum frequency.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20200222005213.3873-9-thara.gopinath@linaro.org
- Fix a spelling mistake in the error message for the stm32 (Colin Ian King)
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRuKdf4M92Gi9vqihve5qtOL396pgUCXjQEIwAKCRDe5qtOL396
prqTAP472tKKudhnEsEsQx0azxYmkW/wCS8fNnrgMkZOE81ibQEAgdmofHjjdSNl
GsPRU5+5tMqQ6isNMYYc2glQpYlB9QA=
=rxjU
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.6-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal fixes from Daniel Lezcano:
- Fix a severe docs build failure for cpu idle cooling device (Randy
Dunlap)
- Fix a spelling mistake in the error message for the stm32 (Colin Ian
King)
* tag 'thermal-v5.6-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal: stm32: fix spelling mistake "preprare" -> "prepare"
Documentation: cpu-idle-cooling: fix a SEVERE docs build failure
This switches the intel pch thermal driver to use
deci_kelvin_to_millicelsius() in <linux/units.h> instead of helpers in
<linux/thermal.h>.
This is preparation for centralizing the kelvin to/from Celsius
conversion helpers in <linux/units.h>.
Link: http://lkml.kernel.org/r/1576386975-7941-7-git-send-email-akinobu.mita@gmail.com
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Sujith Thomas <sujith.thomas@intel.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Amit Kucheria <amit.kucheria@verdurent.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This switches the int340x thermal zone driver to use
deci_kelvin_to_millicelsius() and millicelsius_to_deci_kelvin() in
<linux/units.h> instead of helpers in <linux/thermal.h>.
This is preparation for centralizing the kelvin to/from Celsius
conversion helpers in <linux/units.h>.
Link: http://lkml.kernel.org/r/1576386975-7941-6-git-send-email-akinobu.mita@gmail.com
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Sujith Thomas <sujith.thomas@intel.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Amit Kucheria <amit.kucheria@verdurent.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Fix compilation warning when compiling with make W=1 (Amit Kucheria)
- Code cleanup and refactoring, regmap conversion and add hwmon
support on Qoriq (Andrey Smirnov)
- Add an idle injection cpu cooling device and its documentation,
rename the cpu_cooling device to cpufreq_cooling device (Daniel
Lezcano)
- Convert unexported functions to static, add the __init annotation in
the thermal-of code and remove the pointless wrapper functions
(Daniel Lezcano)
- Fix register offset for Armada XP and register reset bit
initialization (Zak Hays)
- Enable hwmon on the rockchip (Stefan Schaeckeler)
- Add the thermal sensor for the H6/H5/H3/A64/A83T/R40 sun8i platform
and their device tree bindings, followed by a fix for the ths number
and the sparse warnings (Yangtao Li)
- Code cleansup for the sun8i and hwmon support (Yangtao Li)
- Silent some messages which are misleading given the changes made in
the previous version on generic-adc (Martin Blumenstingl)
- Rename exynos to Exynos (Krzysztof Kozlowski)
- Add the bcm2711 thermal driver with the device tree bindings (Stefan
Wahren)
- Use usleep_range() instead of udelay() as the call is always done in
a sleep-able context (Geert Uytterhoeven)
- Do code cleanup and re-organization to set the scene for a new
process for the brcmstb (Florian Fainelli)
- Fix bindings check issues on brcm (Stefan Wahren)
- Add Jasper Lake support on int340x (Nivedita Swaminathan)
- Add Comet Lake support on intel pch (Gayatri Kammela)
- Fix unmatched pci_release_region() on x86 (Chuhong Yuan)
- Remove temperature boundaries for rcar and rcar3 (Niklas Söderlund)
- Fix return value to -ENODEV when thermal_zone_of_sensor_register()
is called with the of-node is missing (Peter Mamonov)
- Code cleanup, interrupt bouncing, and better support on stm32
(Pascal Paillet)
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRuKdf4M92Gi9vqihve5qtOL396pgUCXjAFCAAKCRDe5qtOL396
prIfAQCjhNWKqP3U4oewia9p8dwwfsOpJMqUXge/k6sKzAqscAD/Rg4lWXaayOsX
OWKhS/iL5eN7aXVnSH4MxONsTWhLTAs=
=eZkX
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Depromote debug print on the db8500 platform (Linus Walleij)
- Fix compilation warning when compiling with make W=1 (Amit Kucheria)
- Code cleanup and refactoring, regmap conversion and add hwmon support
on Qoriq (Andrey Smirnov)
- Add an idle injection cpu cooling device and its documentation,
rename the cpu_cooling device to cpufreq_cooling device (Daniel
Lezcano)
- Convert unexported functions to static, add the __init annotation in
the thermal-of code and remove the pointless wrapper functions
(Daniel Lezcano)
- Fix register offset for Armada XP and register reset bit
initialization (Zak Hays)
- Enable hwmon on the rockchip (Stefan Schaeckeler)
- Add the thermal sensor for the H6/H5/H3/A64/A83T/R40 sun8i platform
and their device tree bindings, followed by a fix for the ths number
and the sparse warnings (Yangtao Li)
- Code cleansup for the sun8i and hwmon support (Yangtao Li)
- Silent some messages which are misleading given the changes made in
the previous version on generic-adc (Martin Blumenstingl)
- Rename exynos to Exynos (Krzysztof Kozlowski)
- Add the bcm2711 thermal driver with the device tree bindings (Stefan
Wahren)
- Use usleep_range() instead of udelay() as the call is always done in
a sleep-able context (Geert Uytterhoeven)
- Do code cleanup and re-organization to set the scene for a new
process for the brcmstb (Florian Fainelli)
- Fix bindings check issues on brcm (Stefan Wahren)
- Add Jasper Lake support on int340x (Nivedita Swaminathan)
- Add Comet Lake support on intel pch (Gayatri Kammela)
- Fix unmatched pci_release_region() on x86 (Chuhong Yuan)
- Remove temperature boundaries for rcar and rcar3 (Niklas Söderlund)
- Fix return value to -ENODEV when thermal_zone_of_sensor_register() is
called with the of-node is missing (Peter Mamonov)
- Code cleanup, interrupt bouncing, and better support on stm32 (Pascal
Paillet)
* tag 'thermal-v5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (66 commits)
thermal: stm32: Fix low threshold interrupt flood
thermal: stm32: Improve temperature computing
thermal: stm32: Handle multiple trip points
thermal: stm32: Disable interrupts at probe
thermal: stm32: Rework sensor mode management
thermal: stm32: Fix icifr register name
thermal: of: Make thermal_zone_of_sensor_register return -ENODEV if a sensor OF node is missing
thermal: rcar_gen3_thermal: Remove temperature bound
thermal: rcar_thermal: Remove temperature bound
thermal: intel: intel_pch_thermal: Add Comet Lake (CML) platform support
thermal: intel: Fix unmatched pci_release_region
thermal: int340x: processor_thermal: Add Jasper Lake support
dt-bindings: brcm,avs-ro-thermal: Fix binding check issues
thermal: brcmstb_thermal: Register different ops per process
thermal: brcmstb_thermal: Restructure interrupt registration
thermal: brcmstb_thermal: Add 16nm process thermal parameters
dt-bindings: thermal: Define BCM7216 thermal sensor compatible
thermal: brcmstb_thermal: Prepare to support a different process
thermal: brcmstb_thermal: Do not use DT coefficients
thermal: rcar_thermal: Use usleep_range() instead of udelay()
...
With the STM32 thermal peripheral, it is not possible to dump the
temperature that has caused the interrupt.
When the temperature reaches the low threshold, we generally read
a temperature that is a little bit higher than the low threshold.
This maybe due to sampling precision, and also because the CPU becomes
hotter when it quits WFI mode.
In that case, the framework does not change the trip points. This leads
to a lot of low threshold interrupts.
The fix is to set the low threshold value 0.5 degrees Celsius
below the actual request.
The problem is not so frequent with the high threshold and it would
no be a good idea to set the threshold value higher than the request.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-7-p.paillet@st.com
Change the way of computing to avoid rounds by 1 or 2 degrees.
Also simplify the sampling time management that is hard-coded
to maximum value during probe.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-6-p.paillet@st.com
Let the thermal framework handle the trip points instead
of custom code inside the driver. This is backward compatible,
simplifies the driver and offers the possibility to the user
to set any trip point he needs.
stm_thermal_set_trips callback that is registered to
set_trips ops to handle the low and high thresholds and replaces
stm_thermal_set_threshold and stm_thermal_update_threshold functions.
modify irq enable to handle the thresholds.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-5-p.paillet@st.com
In case of CPU reset, the interrupts could be enabled at boot time.
Disable interrupts and clear flags.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-4-p.paillet@st.com
Be sure get_temp returns an error while disabling or enabling the device.
Set THERMAL_DEVICE_ENABLED state at the end of power on function.
Set THERMAL_DEVICE_DISABLED state at the beginning of power off function.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-3-p.paillet@st.com
When devm_thermal_zone_of_sensor_register() is called from
hwmon_thermal_add_sensor() it is possible that the relevant sensor is
missing an OF node. In this case thermal_zone_of_sensor_register() returns
-EINVAL which causes hwmon_thermal_add_sensor() to fail as well. This patch
changes relevant return code of thermal_zone_of_sensor_register() to
-ENODEV, which is tolerated by hwmon_thermal_add_sensor().
Here is a particular case of such behaviour: the Marvell ethernet PHYs
driver registers hwmon device for the built-in temperature sensor (see
drivers/net/phy/marvell.c). Since the sensor doesn't have associated OF
node devm_hwmon_device_register() returns error which ultimately causes
failure of the PHY driver's probe function.
Signed-off-by: Peter Mamonov <pmamonov@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20190827143952.19591-1-pmamonov@gmail.com
The hardware manual states that the operation of the sensor is not
guaranteed with temperatures above 125°C, not that the readings are
invalid. Remove the bound check and try to deliver temperature readings
even if we are outside the guaranteed operation range.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200117160554.3812787-3-niklas.soderlund+renesas@ragnatech.se
The hardware manual states that the operation of the sensor is not
guaranteed outside the range of -45°C to 125°C, not that the readings
are invalid. Remove the bound check and try to deliver temperature
readings even if we are outside the guaranteed operation range.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200117160554.3812787-2-niklas.soderlund+renesas@ragnatech.se
Add Comet Lake to the list of the platforms to support intel_pch_thermal
driver.
Cc: Zhang rui <rui.zhang@intel.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191211200043.4985-1-gayatri.kammela@intel.com
The driver calls pci_request_regions() in probe and uses
pci_release_regions() in probe failure.
However, it calls pci_release_region() in remove, which does
match the other two calls.
Use pci_release_regions() instead to unify them.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191206075531.18637-1-hslester96@gmail.com
Since we do not have interrupts on BCM7216, we cannot have trip point
crossing, the thermal subsystem expects us to provide a NULL set_trips
operation in that case, so make it possible to provide per-process
thermal_zone_of_device_ops
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200114190607.29339-7-f.fainelli@gmail.com
If we are successful grabbing the interrupt resource, then register an
interrupt handler, this makes it easier to support the interrupt as
being optional, which is it for 7216.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200114190607.29339-6-f.fainelli@gmail.com
Match the 7216 compatible string in order to derive the correct 16nm
process thermal parameters to obtain correct readings.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200114190607.29339-5-f.fainelli@gmail.com
The driver is currently assuming that it is operating with a 28nm
process chip, which has a specific formula to convert temperature to a
code and vice versa. Update the code to support providing two key
values: offset and multiplier to derive the correct formulas.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200114190607.29339-3-f.fainelli@gmail.com
At the time the brcmstb_thermal driver and its binding were merged, the
DT binding did not make the coefficients properties a mandatory one,
therefore all users of the brcmstb_thermal driver out there have a non
functional implementation with zero coefficients. Even if these
properties were provided, the formula used for computation is incorrect.
The coefficients are entirely process specific (right now, only 28nm is
supported) and not board or SoC specific, it is therefore appropriate to
hard code them in the driver given the compatibility string we are
probed with which has to be updated whenever a new process is
introduced.
We remove the existing coefficients definition since subsequent patches
are going to add support for a new process and will introduce new
coefficients as well.
Fixes: 9e03cf1b2d ("thermal: add brcmstb AVS TMON driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200114190607.29339-2-f.fainelli@gmail.com
rcar_thermal_update_temp() takes a mutex, so it is always called in a
context that can sleep. Hence replace the 300 µs busy loop by a call to
usleep_range(), to allow other threads to run.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200115125417.5263-1-geert+renesas@glider.be
Andres Freund