Alsa has an special non-negative return code to indicate device removal
at snd_em28xx_capture_pointer(). Use it, instead of an error code.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove some dead code from em28xx_v4l2_fini() and fix the leaking of the video,
vbi and radio video_device struct memories.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the usb device is disconnected, the resources are no longer available,
so there is no reason to keep them registered.
This will also fix the various sysfs group removal warnings which we can see
since kernel 3.13.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
v4l2_ctrl_handler_free() and v4l2_device_unregister() are currently only called
when the last user closes the device and the device is already disconnected.
But that's wrong, we need to call these functions whenever the em28xx-v4l
extension is closed and we can already do this if the device is still opened
by some users.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
- bail out on unsupported VFL_TYPE
- em28xx_set_mode() needs to be called for VBI and radio mode, too
- em28xx_wake_i2c() needs to be called for VBI and radio mode, too
- em28xx_resolution_set() also needs to be called for VBI
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added command line parameter preallocate_big_buffers so that the digital
transfer buffers can be allocated when the driver is registered. They
do not have to be allocated every time a feed is started.
Signed-off-by: Tim Mester <tmester@ieee.org>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Free what was allocated if there is a failure allocating
transfer buffers.
Stop the feed on a start feed error. The stop feed is not always called
if start feed fails. If the feed is not stopped on error, then the driver
will be stuck so that it can never start feeding again.
[m.chehab@samsung.com: CodingStyle cleanup]
Signed-off-by: Tim Mester <tmester@ieee.org>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that em28xx can be compiled without V4L support, we should
call em28xx_setup_xc3028() on both em28xx-v4l and em28xx-dvb
modules.
Reported-by: Chris Lee <updatelee@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The URB calculus code may eventually be moved to some other
place, like at pcm open, if it ends by needing more setups, like
working with different bit rates, or different audio latency.
So, move it into a separate routine. That also makes the code
more readable.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pulseaudio has the bad habit of stopping a streaming audio if
a device, opened in non-block mode, waits.
It is impossible to avoid em28xx to wait, as it will send commands
via I2C, and other I2C operations may be happening (firmware
transfers, Remote Controller polling, etc). Yet, as each em28xx
subdriver locks em28xx-dev to protect the access to the hardware,
it is possible to minimize the audio glitches by returning -EAGAIN
to pulseaudio, if the lock is already taken by another subdriver.
Reported-by: Antti Palosaari <crope@iki.fi>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the period size is wrong, userspace will assume a wrong delay
any may negociate an inadequate value.
The em28xx devices use 8 for URB interval, in microframes,
and the driver programs it to have 64 packets.
That means that the IRQ sampling period is 125 * 8 * 64,
with is equal to 64 ms.
So, that's the minimal latency with the current settings. It is
possible to program a lower latency, by using less than 64 packets,
but that increases the amount of bandwitdh used, and the number of
IRQ events per second.
In any case, in order to support it, the driver logic should be
changed to fill those parameters in realtime.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The current code hardcodes the number of audio URBs, the number
of packets per URB and the maximum URB size.
This is not a good idea, as it:
- wastes more bandwidth than necessary, by using a very
large number of packets;
- those constants are bound to an specific scenario, with
a bandwidth of 48 kHz;
- don't take the maximum endpoint size into account;
- with urb->interval = 1 on xHCI, those constraints cause a "funny"
setup: URBs with 64 packets inside, with only 24 bytes total. E. g.
a complete waste of space.
Change the code to do dynamic URB audio calculus and allocation.
For now, use the same constraints as used before this patch, to
avoid regressions.
A good scenario (tested) seems to use those defines, instead:
#define EM28XX_MAX_AUDIO_BUFS 8
#define EM28XX_MIN_AUDIO_PACKETS 2
But let's not do such change here, letting the optimization to
happen on latter patches, after more tests.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just filling urb->interval with 1 is wrong, and causes a different
behaviour with xHCI.
With EHCI, the URB size is typically 192 bytes. However, as
xHCI specifies intervals in microframes, the URB size becomes
too short (24 bytes).
With this patch, the interval will be properly initialized, and
the device will behave the same if connected into a xHCI or an
EHCI device port.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If i2c_debug is enabled, we splicitly want to know when a
device fails with timeout.
If i2c_debug==2, this is already provided, for each I2C transfer
that fails.
However, most of the time, we don't need to go that far. We just
want to know that I2C transfers fail.
So, add such errors for normal (ret == 0x10) I2C aborted timeouts.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The I2C output messages is too polluted. Clean it a little
bit, by:
- use the proper core support for memory dumps;
- hide most stuff under the i2c_debug umbrella;
- add the missing KERN_CONT where needed;
- use 2 levels or verbosity. Only the second one
will show the I2C transfer data.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Follow the error codes for I2C as described at Documentation/i2c/fault-codes.
In the case of the I2C status register (0x05), this is mapped into:
- ENXIO - when reg 05 returns 0x10
- ETIMEDOUT - when the device is not temporarily not responding
(e. g. reg 05 returning something not 0x10 or 0x00)
- EIO - for generic I/O errors that don't fit into the above.
In the specific case of 0-byte reads, used only during I2C device
probing, it keeps returning -ENODEV.
TODO: return EBUSY when reg 05 returns 0x20 on em2874 and upper.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In the lack of a better spec, let's assume the timeout
values compatible with SMBus spec:
http://smbus.org/specs/smbus110.pdf
at chapter 8 - Electrical Characteristics of SMBus devices
Ok, SMBus is a subset of I2C, and not all devices will be
following it, but the timeout value before this patch was not
even following the spec.
So, while we don't have a better guess for it, use 35 + 1
ms as the timeout.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This macro is used by all em28xx devices, and not just em2800.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The I2C wait completion/timeout logic currently assumes that
msleep(5) will wait exaclty 5 ms. This is not true at all,
as it depends on CONFIG_HZ.
Convert it to use jiffies, in order to not wait for more time
than needed.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of assuming that msleep() is precise, use a jiffies
based code to wait for AC97 to be available.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of allocating/deallocating URBs and transfer buffers
every time stream is started/stopped, just do it once.
That reduces the memory allocation pressure and makes the
code that start/stop streaming a way simpler.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of allocating transfer buffers with kmalloc() use
usb_alloc_coherent().
This patch should make it work also with ARM CPUs.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The rest of the function uses ret to store the return value, even setting
ret to i a few lines before this, so return ret instead of i.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix continuation lines.
[m.chehab@samsung.com: This was actually part of a v2 patch meant to
fix i2c debug prints. As version 1 was already applied, I'm applying
here the diff and fixing the patch subject/description]
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The audio configuration in chip config register 0x00 and eeprom are always
consistent. But currently the audio configuration #defines for the chip config
register say 0x20 means 3 sample rates and 0x30 5 sample rates, while the eeprom
info output says 0x20 means 1 sample rate and 0x30 3 sample rates.
I've checked the datasheet excerpts I have and it seems that the meaning of
these bits is different for em2820/40 (1 and 3 sample rates) and em2860+
(3 and 5 smaple rates).
I have also checked my Hauppauge WinTV USB 2 (em2840) and the chip/eeprom
audio config 0x20 matches the sample rates reproted by the USB device
descriptor (32k only).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by the kbuild test robot:
All error/warnings:
>> ERROR: "em28xx_release_resources" [drivers/media/usb/em28xx/em28xx-v4l.ko] undefined!
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Emitting an OOM message isn't necessary after input_allocate_device
as there's a generic OOM and a dump_stack already done.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Do not shift the already 7bit i2c address.
Print a message also for write+read transactions.
For write+read, print the read buffer correctly instead of using the write
buffer.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The two drivers LGDT3305 and TDA18271C2DD were not autoselected, so the
cx231xx_dvb module could not be loaded when MEDIA_SUBDRV_AUTOSELECT=y.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
A few devices (em2860) use a separate interface for audio only
Audio Vendor Class USB. That interface should not be used by
Remote Controller, Analog TV or Digital TV.
Prevents initializing all non-audio extensions for the audio
only interface.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the same module version on all em28xx sub-modules, and use
the same naming convention to describe the driver.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Better to split chipset detection from the audio setup. So, move the
detection code to em28xx_init_dev().
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a message with consistent prints before and after each
extension initialization, and provide a better text for module
load.
While here, add a missing sanity check for extension finish
code at em28xx-v4l extension.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that all analog-specific code are at em28xx-video, convert
it into an em28xx extension and load it as a separate module.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix the error handling logic, making it to unregister i2c bus 0, in
case of a failure to register the second bus.
Reported-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several init code inside em28xx-cards that are actually
part of analog initialization. Move the code to em28x-video, in
order to remove part of the mess.
In thesis, no functional changes so far.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When em28xx extensions are loaded/removed, there are two locks:
a single static em28xx_devlist_mutex that registers each extension
and the struct em28xx dev->lock.
When extensions are registered, em28xx_devlist_mutex is taken first,
and then dev->lock.
Be sure that, when extensions are being removed, the same order
will be used.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In order to make easier for the next patches, do some
cosmetic changes.
No functional changes.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that we want to split the video handling to a separate
module, move all video-specific functions to em28xx-video.
No functional changes.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
PLL was attached twice to frontend0 leaving frontend1 without a tuner.
frontend0 is DVB-C and frontend1 is DVB-T.
Cc: stable@vger.kernel.org
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
For GPI-connected buttons without (hardware) debouncing, the polling interval
needs to be reduced to detect button presses properly.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
During the last media summit meeting it was decided to move this driver to
staging as the first step to removing it altogether.
Most webcams covered by this driver are now supported by gspca. Nobody has the
hardware to convert the remaining devices to gspca.
This driver needs a major overhaul to have it conform to the latest frameworks
and compliancy tests.
Without hardware, however, this is next to impossible. Given the fact that
this driver seems to be pretty much unused (it has been removed from Fedora
several versions ago and nobody complained about that), we decided to drop
this driver.
This patch moves it to staging. Some time in 2014 we will drop it completely.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
GIT_AUTHOR_DATE=1386943312
Add USB IDs for the WinFast DTV Dongle Mini.
Device is tested and works fine under MythTV
Signed-off-by: Robert Backhaus <robbak@robbak.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Convert driver from proprietary DVB driver model to standard I2C
driver model.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
New chip version, which is very similar than EM28174.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Merge the media fixes merged upstream for v3.13-rc4
* upstream-fixes: (30 commits)
[media] videobuf2-dma-sg: fix possible memory leak
[media] vb2: regression fix: always set length field.
[media] mt9p031: Include linux/of.h header
[media] rtl2830: add parent for I2C adapter
[media] media: marvell-ccic: use devm to release clk
[media] ths7303: Declare as static a private function
[media] em28xx-video: Swap release order to avoid lock nesting
[media] usbtv: Add support for PAL video source
[media] media_tree: Fix spelling errors
[media] videobuf2: Add support for file access mode flags for DMABUF exporting
[media] radio-shark2: Mark shark_resume_leds() inline to kill compiler warning
[media] radio-shark: Mark shark_resume_leds() inline to kill compiler warning
[media] af9035: unlock on error in af9035_i2c_master_xfer()
[media] af9033: fix broken I2C
[media] v4l: omap3isp: Don't check for missing get_fmt op on remote subdev
[media] af9035: fix broken I2C and USB I/O
[media] wm8775: fix broken audio routing
[media] marvell-ccic: drop resource free in driver remove
[media] tef6862/radio-tea5764: actually assign clamp result
[media] cx231xx: use after free on error path in probe
...
The SpeedLink Vicious And Devine Laplace webcam is using an EM2765 bridge and
an OV2640 sensor. It has a built-in microphone (USB standard device class)
and provides 3 buttons (snapshot, illumination, mute) and 2 LEDs (capturing/mute
and illumination/flash). It is also equipped with an eeprom.
The device is available in two colors: white (1ae7:9003) and black (1ae7:9004).
For further details see http://linuxtv.org/wiki/index.php/VAD_Laplace.
Please note the following limitations that need to be addressed later:
- resolution limited to 640x480 (sensor supports 1600x1200)
- picture quality needs to be improved
- AV-mute button doesn't work yet
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The SpeedLink VAD Laplace webcam is equipped with an illumination button and
an illumination LED. When the button is pressed, the driver must toggle the
LED state via the corresponding GPO port.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Introduce a LED role and store all LEDs in an array.
Also provide a helper function to retrieve a specific LED.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
So far, the driver only supports a snapshot button which is assigned to
register 0x0c bit 5. This special port has a built-in debouncing mechanism.
For buttons connected to ordinary GPI ports, this patch implements a software
debouncing mechanism.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The current code supports only a single snapshot button assigned to
register 0x0c bit 5. But devices may be equipped with multiple buttons
with different functionalities and they can also be assigned to the
various GPI-ports.
Extend the em28xx-input code to handle multiple buttons assigned to different
GPI-ports / register addresses and bits.
Also make easier to extend the code with further button types.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some devices are equipped with a capturing status LED that needs to be
switched on/off explicitly via a GPO port.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We recently introduced some new error paths but the unlocks are missing.
Fixes: 0065a79a86 ('[media] dw2102: Don't use dynamic static allocation')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We recently introduced some new error paths which are missing their
unlocks.
Fixes: 64f7ef8afb ('[media] cxusb: Don't use dynamic static allocation')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It is IT9135 dual design.
Thanks to Michael Piko for reporting that!
Reported-by: Michael Piko <michael@piko.com.au>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is similar to the Terratec H7. It works with the same az6007 firmware as
the former, however the drx-k firmware of the H7 will NOT work. Hence use
a different firmware name. The firmware does not need to exist as the one in
the eeprom is just fine as long as the h7 one doesn't get loaded, but maybe
some day someone wants to load it (the one from the h5 would work too).
Also since the config entry is now different anyway disable support for rc.
AFAIK the Technisat remote (TS35) is RC5 and the code (which a code comment
claims doesn't work anyway) only would handle NEC hence it's pointless creating
a device and polling it if we already know it can't work.
CI is untested.
Originally based on idea found on
http://www.linuxtv.org/wiki/index.php/TechniSat_CableStar_Combo_HD_CI claiming
only id needs to be added (but failed to mention it only worked because the
driver couldn't find the h7 drx-k firmware...).
Signed-off-by: Roland Scheidegger <rscheidegger_lists@hispeed.ch>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
vb2_fop_release might take the video queue mutex lock.
In order to avoid nesting mutexes the private mutex is taken after the
fop_release has finished.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We introduced a couple new error paths which are missing unlocks.
Fixes: 7760e14835 ('[media] af9035: Don't use dynamic static allocation')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable@vger.kernel.org
There was three small buffer len calculation bugs which caused
driver non-working. These are coming from recent commit:
commit 7760e14835
[media] af9035: Don't use dynamic static allocation
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable@vger.kernel.org
vb2_fop_release might take the video queue mutex lock.
In order to avoid nesting mutexes the private mutex is taken after the
fop_release has finished.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We dereference "dev" after it has already been freed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It is IT9135 dual design.
Thanks to Michael Piko for reporting that!
Reported-by: Michael Piko <michael@piko.com.au>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The variable txlen was used instead of rxlen in boundary check.
(copy-paste error)
Signed-off-by: Felipe Pena <felipensp@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a small delay at the end of configure_clock() to allow sensor to initialize.
This is needed by Asus VX2S laptop webcam to detect sensor type properly (the already-supported MT9M112).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media build fixes from Mauro Carvalho Chehab:
"A series of patches that fix compilation on non-x86 archs.
While most of them are just build fixes, there are some fixes for real
bugs, as there are a number of drivers using dynamic stack allocation.
A few of those might be considered a security risk, if the i2c-dev
module is loaded, as someone could be sending very long I2C data that
could potentially overflow the Kernel stack. Ok, as using /dev/i2c-*
devnodes usually requires root on usual distros, and exploiting it
would require a DVB board or USB stick, the risk is not high"
* 'topic/kbuild-fixes-for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (28 commits)
[media] platform drivers: Fix build on frv arch
[media] lirc_zilog: Don't use dynamic static allocation
[media] mxl111sf: Don't use dynamic static allocation
[media] af9035: Don't use dynamic static allocation
[media] af9015: Don't use dynamic static allocation
[media] dw2102: Don't use dynamic static allocation
[media] dibusb-common: Don't use dynamic static allocation
[media] cxusb: Don't use dynamic static allocation
[media] v4l2-async: Don't use dynamic static allocation
[media] cimax2: Don't use dynamic static allocation
[media] tuner-xc2028: Don't use dynamic static allocation
[media] tuners: Don't use dynamic static allocation
[media] av7110_hw: Don't use dynamic static allocation
[media] stv090x: Don't use dynamic static allocation
[media] stv0367: Don't use dynamic static allocation
[media] stb0899_drv: Don't use dynamic static allocation
[media] dvb-frontends: Don't use dynamic static allocation
[media] dvb-frontends: Don't use dynamic static allocation
[media] s5h1420: Don't use dynamic static allocation
[media] uvc/lirc_serial: Fix some warnings on parisc arch
...
Pull media updates from Mauro Carvalho Chehab:
"This series include:
- a new Remote Controller driver for ST SoC with the corresponding DT
bindings
- a new frontend (cx24117)
- a new I2C camera flash driver (lm3560)
- a new mem2mem driver for TI SoC (ti-vpe)
- support for Raphael r828d added to r820t driver
- some improvements on buffer allocation at VB2 core
- usual driver fixes and improvements
PS this time, we have a smaller number of patches. While it is hard
to pinpoint to the reasons, I believe that it is mainly due to:
1) there are several patch series ready, but depending on DT review.
I decided to grant some extra time for DT maintainers to look on
it, as they're expecting to have more time with the changes agreed
during ARM mini-summit and KS. If they can't review in time for
3.14, I'll review myself and apply for the next merge window.
2) I suspect that having both LinuxCon EU and LinuxCon NA happening
during the same merge window affected the development
productivity, as several core media developers participated on
both events"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (151 commits)
[media] media: st-rc: Add ST remote control driver
[media] gpio-ir-recv: Include linux/of.h header
[media] tvp7002: Include linux/of.h header
[media] tvp514x: Include linux/of.h header
[media] ths8200: Include linux/of.h header
[media] adv7343: Include linux/of.h header
[media] v4l: Fix typo in v4l2_subdev_get_try_crop()
[media] media: i2c: add driver for dual LED Flash, lm3560
[media] rtl28xxu: add 15f4:0131 Astrometa DVB-T2
[media] rtl28xxu: add RTL2832P + R828D support
[media] rtl2832: add new tuner R828D
[media] r820t: add support for R828D
[media] media/i2c: ths8200: fix build failure with gcc 4.5.4
[media] Add support for KWorld UB435-Q V2
[media] staging/media: fix msi3101 build errors
[media] ddbridge: Remove casting the return value which is a void pointer
[media] ngene: Remove casting the return value which is a void pointer
[media] dm1105: remove unneeded not-null test
[media] sh_mobile_ceu_camera: remove deprecated IRQF_DISABLED
[media] media: rcar_vin: Add preliminary r8a7790 support
...
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb-v2/mxl111sf.c:74:1: warning: 'mxl111sf_ctrl_msg' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb-v2/af9035.c:142:1: warning: 'af9035_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb-v2/af9035.c:305:1: warning: 'af9035_i2c_master_xfer' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb-v2/af9015.c:433:1: warning: 'af9015_eeprom_hash' uses dynamic stack allocation [enabled by default]
In this specific case, it is a gcc bug, as the size is a const, but
it is easy to just change it from const to a #define, getting rid of
the gcc warning.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb/dw2102.c:368:1: warning: 'dw2102_earda_i2c_transfer' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb/dw2102.c:449:1: warning: 'dw2104_i2c_transfer' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb/dw2102.c:512:1: warning: 'dw3101_i2c_transfer' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb/dw2102.c:621:1: warning: 's6x0_i2c_transfer' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb/dibusb-common.c:124:1: warning: 'dibusb_i2c_msg' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb/cxusb.c:209:1: warning: 'cxusb_i2c_xfer' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb/cxusb.c:69:1: warning: 'cxusb_ctrl_msg' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On this arch, usec is not unsigned long. So, we need to typecast,
in order to remove those warnings:
drivers/media/usb/uvc/uvc_video.c: In function 'uvc_video_clock_update':
drivers/media/usb/uvc/uvc_video.c:678:2: warning: format '%lu' expects argument of type 'long unsigned int', but argument 9 has type '__kernel_suseconds_t' [-Wformat]
drivers/staging/media/lirc/lirc_serial.c: In function 'irq_handler':
drivers/staging/media/lirc/lirc_serial.c:707:5: warning: format '%lx' expects argument of type 'long unsigned int', but argument 6 has type '__kernel_suseconds_t' [-Wformat]
drivers/staging/media/lirc/lirc_serial.c:707:5: warning: format '%lx' expects argument of type 'long unsigned int', but argument 7 has type '__kernel_suseconds_t' [-Wformat]
drivers/staging/media/lirc/lirc_serial.c:719:5: warning: format '%lx' expects argument of type 'long unsigned int', but argument 6 has type '__kernel_suseconds_t' [-Wformat]
drivers/staging/media/lirc/lirc_serial.c:719:5: warning: format '%lx' expects argument of type 'long unsigned int', but argument 7 has type '__kernel_suseconds_t' [-Wformat]
drivers/staging/media/lirc/lirc_serial.c:728:6: warning: format '%lx' expects argument of type 'long unsigned int', but argument 6 has type '__kernel_suseconds_t' [-Wformat]
drivers/staging/media/lirc/lirc_serial.c:728:6: warning: format '%lx' expects argument of type 'long unsigned int', but argument 7 has type '__kernel_suseconds_t' [-Wformat]
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Components are RTL2832P + R828D + MN88472.
Currently support only DVB-T as there is no driver for MN88472 demod.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
RTL2832P is version of RTL2832U with extra TS interface.
As for now, we support only integrated RTL2832 demod.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for the UB435-Q V2. You might need to
use the device once with the Windows driver provided by KWorld
in order to permanently reprogram the device descriptors. Thanks
to Jarod Wilson for the initial attempt at adding support for this
device.
[m.chehab@samsung.com: Fixed Whitespace mangling, Coding Style and
improved the error handling at DVB attach]
Signed-off-by: Jean-Francois Thibert <jfthibert@google.com>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The em28xx driver only calls subdevices' .s_power() method to power them
down, relying on the hardware to wake up automatically, which is usually
the case with tuners. This was acceptable with the old .standby() method,
but is wrong with .s_power(). Fixing the driver would be difficult due to
a broad supported hardware base. Instead this patch makes use of the
unbalanced_power soc-camera subdevice flag to tell the ov2640 driver to
balance calls to v4l2_clk_enable() and v4l2_clk_disable() internally.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Camera sensors usually require a master clock for data sampling. This patch
registers such a clock source for em28xx cameras. This fixes the currently
broken em28xx ov2640 camera support and can also be used by other camera
sensors.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some architectures do not support PCI, but still support USB, so need
let our usb driver try to use usb_* instead of pci_* to support these
architectures, or can not pass compiling.
The related error (with allmodconfig for arc):
CC [M] drivers/media/usb/b2c2/flexcop-usb.o
drivers/media/usb/b2c2/flexcop-usb.c: In function ‘flexcop_usb_transfer_exit’:
drivers/media/usb/b2c2/flexcop-usb.c:393: error: implicit declaration of function ‘pci_free_consistent’
drivers/media/usb/b2c2/flexcop-usb.c: In function ‘flexcop_usb_transfer_init’:
drivers/media/usb/b2c2/flexcop-usb.c:410: error: implicit declaration of function ‘pci_alloc_consistent’
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The variable frame_ready is only assigned the values true and false.
Change its type to bool.
The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):
@exists@
type T;
identifier b;
@@
- T
+ bool
b = ...;
... when any
b = \(true\|false\)
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The pan/tilt absolute control value is signed value. If minimum value
is minus, It will be changed to plus by clamp_t() as commit 64ae9958a6.
([media] uvcvideo: Fix control value clamping for unsigned integer controls).
It leads to wrong setting of the control values. For example,
when min and max are -36000 and 36000, the setting value between of this range
is always 36000. So, its data type should be changed to signed.
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Increase the streaming_users count only if streaming start succeeds.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix CodingStyle on the GPIO init tables.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are numerous issues in error handling code of cx231xx initialization.
Double free (when cx231xx_init_dev() calls kfree(dev) via cx231xx_release_resources()
and then cx231xx_usb_probe() does the same) and memory leaks
(e.g. usb_get_dev() before (ifnum != 1) check in cx231xx_usb_probe())
are just a few of them.
The patch fixes the issues in cx231xx_usb_probe() and cx231xx_init_dev()
by moving usb_get_dev(interface_to_usbdev(interface)) below in code and
implementing proper error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/dvb-usb/az6027.c:257:23: warning: symbol 'az6027_stb0899_config' was not declared. Should it be static?
drivers/media/usb/dvb-usb/az6027.c:294:23: warning: symbol 'az6027_stb6100_config' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/tlg2300/pd-main.c:235:25: warning: incorrect type in assignment (different base types)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/cx231xx/cx231xx-pcb-cfg.c:31:19: warning: symbol 'cx231xx_Scenario' was not declared. Should it be static?
drivers/media/usb/cx231xx/cx231xx-pcb-cfg.c:675:23: warning: cast to restricted __le32
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/pvrusb2/pvrusb2-hdw.c:2871:13: warning: symbol 'pvr2_hdw_get_detected_std' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dear Hans de Goede, I have Ubuntu (raring) and recently bought digital
microscope eyepiece Lomo MD300. It is the same device as Future Optics MVV3000.
Unfortunately it does not work out of box. Moreover drivers refused to work
under Windows 7 as well leaving me only with Win Xp working system. I have had
no choice but to examine what happened in USB bus and attempt to reproduce the
sequence. So, i have download the source(3.8.0-30 kernel) and made required
changes to driver to make my hardware work.
I submit my changed files to you as maintainer of the driver so you can
integrade my changes into main stream. Thanx. Hopefully my Ubuntu will work
with my hardware out of box.
Sincerely yours Vladik Aranov
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That version of DRX-K chip supports only 2.
drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
drxk: Warning -22 on qam_demodulator_command
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
tda18271c2dd => tda18271
tda18271 is more complete than tda18271c2dd.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Downloading new firmware for DRX-K demodulator is not obligatory but
usually it offers important bug fixes compared to default firmware
burned into chip rom. DRX-K demod driver will continue even without
the firmware, but in that case it will print warning to system log
to tip user he should install firmware.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The Stellar firmware load routine is different. Improve it to use
the default firmware, if no modprobe parameter tells otherwise.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tested-by: André Roth <neolynx@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since kernel 3.8, the initialization for Stellar (sms1000)
devices are broken.
Those devices have a behaviour different than usual sms1100
and sms2270: they start with one USB ID (devices in cold state),
but after firmware load, they get a different USB ID.
This weren't docummented at the driver. So, the patches that added
support for sms2270 broke it.
Properly documment it, and provide a debug log that allows to
follow all phases of the device initialization:
smsusb_probe: board id=13, interface number 0
smsusb_probe: interface 0 won't be used. Expecting interface 1 to popup
smsusb_probe: board id=13, interface number 1
smsusb_probe: smsusb_probe 1
smsusb_probe: endpoint 0 81 02 64
smsusb_probe: endpoint 1 02 02 64
smsusb_probe: stellar device in cold state was found at usb\4-2.
smsusb1_load_firmware: sent 38144(38144) bytes, rc 0
smsusb1_load_firmware: read FW dvbt_bda_stellar_usb.inp, size=38144
smsusb_probe: stellar device now in warm state
usbcore: registered new interface driver smsusb
usb 4-2: USB disconnect, device number 52
usb 4-2: new full-speed USB device number 53 using uhci_hcd
usb 4-2: New USB device found, idVendor=187f, idProduct=0100
usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-2: Product: SMS DVBT-BDA Receiver
usb 4-2: Manufacturer: Siano Mobile Silicon
smsusb_probe: board id=1, interface number 0
smsusb_probe: smsusb_probe 0
smsusb_probe: endpoint 0 81 02 64
smsusb_probe: endpoint 1 02 02 64
smsusb_init_device: in_ep = 81, out_ep = 02
smscore_register_device: allocated 50 buffers
smscore_register_device: device ffff88012a00bc00 created
smsusb_init_device: smsusb_start_streaming(...).
smscore_set_device_mode: set device mode to 4
smsusb1_detectmode: 4 "SMS DVBT-BDA Receiver"
smsusb_sendrequest: sending MSG_SMS_INIT_DEVICE_REQ(578) size: 12
smsusb_onresponse: received MSG_SMS_INIT_DEVICE_RES(579) size: 12
smscore_set_device_mode: Success setting device mode.
smscore_init_ir: IR port has not been detected
smscore_start_device: device ffff88012a00bc00 started, rc 0
smsusb_init_device: device 0xffff88002cfa6000 created
smsusb_probe: Device initialized with return code 0
DVB: registering new adapter (Siano Stellar Digital Receiver)
usb 4-2: DVB: registering adapter 0 frontend 0 (Siano Mobile Digital MDTV Receiver)...
smscore_register_client: ffff88012174a000 693 1
sms_board_dvb3_event: DVB3_EVENT_HOTPLUG
smsdvb_hotplug: success
smsdvb_module_init:
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tested-by: André Roth <neolynx@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some messages are not clear, some are debug data, but are
shown as errors, and one message is duplicated.
Cleanup that mess in order to provide a cleaner log.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tested-by: André Roth <neolynx@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is an asymmetry in ttusb_dec_init_usb()-ttusb_init_rc()
and ttusb_dec_exit_usb()-ttusb_dec_exit_rc() in terms of resources
allocated-deallocated. irq_urb and irq_buffer are allocated in
ttusb_dec_init_usb(), while they are deallocated in ttusb_dec_exit_rc().
As a result there is a leak of them in ttusb_dec_probe().
The patch fixes the asymmetry and a leak on a failure path in ttusb_dec_init_usb().
By the way, it
- removes usage of -1 as a custom error code,
- replaces GFP_ATOMIC by GFP_KERNEL in usb_alloc_coherent() in ttusb_dec_init_usb()
as soon as all other memory allocation done with GFP_KERNEL;
- refactors ttusb_dec_boot_dsp() in an equivalent way except for returning 0
instead of 1 if ttusb_dec_boot_dsp() succeed in (!mode) branch.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the tuner part of the ds3000 driver was split to share code with the m88rs2000 driver, the ts2020 driver used
the frequency divider value from the m88rs2000 driver. However the ds3000 driver requires a different value, and this
resulted in some frequecies being invisible to the tuner. This patch adds back in the value needed for the ds3000 driver
and configured as an option in the dw2102 frontend driver.
It may also apply to su3000 devices, which use the same ds3000 driver, but for now it is only applied to the s660 device.
Signed-off-by: John Horan <knasher@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of passing each byte through stack let's use %*ph specifier to do this
job better.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add variable resolution support to Syntek STK1135 subdriver.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add variable resolution support to gspca by allowing subdrivers to
specify try_fmt and enum_framesizes functions.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Store complete current mode (struct v4l2_pix_format) in struct gspca_dev
instead of separate pixfmt, width and height parameters.
This is a preparation for variable resolution support.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The owner knows the system as "LX INFINITI Powerlite".
DMI information for this system:
System Information
Manufacturer: HCL Infosystems Limited
Product Name: T12Rg-H
Version: 1.0
Serial Number: B073A1189988
UUID: 326B3F00-001D-602F-CFD2-4E45435F4349
Wake-up Type: Power Switch
SKU Number:
Family:
Handle 0x0002, DMI type 2, 15 bytes
Base Board Information
Manufacturer: HCL Infosystems Limited
Product Name: T12Rg-H
Version: 1.0
Serial Number: BSN12345678901234567
Asset Tag: ATN12345678901234567
Features:
Board is a hosting board
Board is replaceable
Location In Chassis:
Chassis Handle: 0x0003
Type: Motherboard
Contained Object Handles: 0
Bus 001 Device 003: ID 05e1:0501 Syntek Semiconductor Co., Ltd DC-1125 Webcam
Signed-off-by: Gregor Jasny <gjasny@googlemail.com>
Reported-by: Noopur Srivastava <noopur.018@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The owner knows the system as "LX INFINITI Powerlite".
DMI information for this system:
System Information
Manufacturer: HCL Infosystems Limited
Product Name: T12Rg-H
Version: 1.0
Serial Number: B073A1189988
UUID: 326B3F00-001D-602F-CFD2-4E45435F4349
Wake-up Type: Power Switch
SKU Number:
Family:
Handle 0x0002, DMI type 2, 15 bytes
Base Board Information
Manufacturer: HCL Infosystems Limited
Product Name: T12Rg-H
Version: 1.0
Serial Number: BSN12345678901234567
Asset Tag: ATN12345678901234567
Features:
Board is a hosting board
Board is replaceable
Location In Chassis:
Chassis Handle: 0x0003
Type: Motherboard
Contained Object Handles: 0
Bus 001 Device 003: ID 05e1:0501 Syntek Semiconductor Co., Ltd DC-1125 Webcam
Signed-off-by: Gregor Jasny <gjasny@googlemail.com>
Reported-by: Noopur Srivastava <noopur.018@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The camera doesn't implement GET_DEF on the video probe control and
can crash when it receives the request depending on timings. Set the
PROBE_DEF quirk to work around the problem.
Reported-by: Jürgen Liebmann <info@pirna-esw6.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
Set the config structure pointer to the eeprom data pointer (data,
here eedata dereferenced) not the pointer to the pointer to
the eeprom data (eedata itself).
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: stable@vger.kernel.org # for v3.10
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
free_buff_list and rec_buff_list are initialized in the middle of hdpvr_probe(),
but if something bad happens before that, error handling code calls hdpvr_delete(),
which contains iteration over the lists (via hdpvr_free_buffers()).
The patch moves the lists initialization to the beginning and by the way fixes
goto label in error handling of registering videodev.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
Ignore out of order data and mark incomplete buffers as errored.
This gets rid of annoying flicker due to occassional garbage from hardware.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-media@vger.kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
The image data is laid out a bit more weirdly and thus needs more work to
properly interlace. What we get from hardware is V4L2_FIELD_ALTERNATE, but
since userspace support for it is practically nonexistent, thus we make
V4L2_FIELD_INTERLACED from it so that it's more easily interpreted.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
As reported by Fengguang Wu <fengguang.wu@intel.com>
drivers/built-in.o: In function `vb2_ioctl_streamon':
>> (.text+0x8d354): undefined reference to `video_devdata'
drivers/built-in.o: In function `vb2_ioctl_streamoff':
>> (.text+0x8d397): undefined reference to `video_devdata'
drivers/built-in.o: In function `vb2_ioctl_expbuf':
...
That happens when:
CONFIG_VIDEO_DEV=y
CONFIG_VIDEO_V4L2=m
CONFIG_VIDEO_USBTV=y
As the core is module, usbtv should also be compiled as module.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is a camera with an ov518+ revision 0 bridge + ov7620ae sensor,
which appearently needs different handling then the Trust spacecam 320, which
has an ov518+ revision 2 + ov7620ae sensor. The Terracam USB Pro used to write
this patch has kindly been provided by
Dr. Tilmann Bubeck <t.bubeck@reinform.de>.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It's the only function in v4l2-dv-timings.c with the v4l prefix instead
of v4l2. Make it consistent with the other functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The KWorld UB445-U is similar to the UB430-AF but with a Samsung S5H1411
frontend. Luckily all of the hardware is already well supported, just the
device and USB ids need to be added to get it to work.
Signed-off-by: Johannes Erdfelt <johannes@erdfelt.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hello,
this is a new gspca driver for Syntek STK1135 webcams. The code is completely
new, but register values are based on Syntekdriver (stk11xx) by Nicolas VIVIEN
(http://syntekdriver.sourceforge.net).
Only one webcam type is supported now - vendor 0x174f, device 0x6a31.
It's Asus F5RL laptop flippable webcam with MT9M112.
The camera works better than in Windows - initializes much faster and
provides more resolutions (the sensor can do almost any resolution - just
add it to the stk1135_modes[] - could this feature be somehow used by
applications to avoid SW scaling?).
Autoflip works too - when the camera is flipped around, the image is flipped
automatically.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If v4l2_fh_open() fails in dev_open(), gspca_dev->module left locked.
The patch adds module_put(gspca_dev->module) on this path.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the new defines to calculate the full blanking and frame sizes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
v4l2-common.c contained a bunch of dv-timings related functions.
Move that to the new v4l2-dv-timings.c which is a more appropriate
place for them.
There aren't many drivers that do HDTV, so it is a good idea to separate
common code related to that into a module of its own.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Deferred probe was added in order to avoid udev vs. Kernel firmware
download problems. It is not needed anymore.
https://bugzilla.redhat.com/show_bug.cgi?id=827538
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No need to access bInterfaceNumber via dvb_usb_v2 internals as driver
has it already.
That patch is prepare for dvb_usb_v2 deferred probe hack removal. It was
added due to udev firmware loading problems, but things are fixed after
that and it is not needed anymore.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by Randy Dunlap:
When CONFIG_SND=m and CONFIG_SND_AC97_CODEC=m and
CONFIG_VIDEO_STK1160=y
CONFIG_VIDEO_STK1160_AC97=y
drivers/built-in.o: In function `stk1160_ac97_register':
(.text+0x122706): undefined reference to `snd_card_create'
drivers/built-in.o: In function `stk1160_ac97_register':
(.text+0x1227b2): undefined reference to `snd_ac97_bus'
drivers/built-in.o: In function `stk1160_ac97_register':
(.text+0x1227cd): undefined reference to `snd_card_free'
drivers/built-in.o: In function `stk1160_ac97_register':
(.text+0x12281b): undefined reference to `snd_ac97_mixer'
drivers/built-in.o: In function `stk1160_ac97_register':
(.text+0x122832): undefined reference to `snd_card_register'
drivers/built-in.o: In function `stk1160_ac97_unregister':
(.text+0x12285e): undefined reference to `snd_card_free'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Removes unnecessary query of buffer state. The code already checks if stream is active or not.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This one must have missed the conversion "c003ab1b [media] rc-core:
add separate defines for protocol bitmaps and numbers".
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Set fmt.pix.priv to zero in vidioc_try_fmt_vid_cap.
Catched by v4l2-compliance.
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
[hans.verkuil@cisco.com: dropping unnecessary change to g_fmt_vid_cap]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This commit adds an early check to vidioc_s_std() to detect if the
new and current standards are equal, and exit with success in that
case.
This is needed to prevent userspace applications that might attempt
to re-set the same standard from failing if that's done when streaming
has started.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove the check as there's no reason to prevent the input from
being set when the device is streaming. This allows surveillance
applications (such as motion, zoneminder, etc.) to configure the
input while streaming.
Reported-by: Sergey 'Jin' Bostandzhyan <jin@mediatomb.cc>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
check_firmware() makes sure firmware is in a device.
It returns zero on success and error code otherwise.
Also it sets down_firmware flag to 1 if downloading occurs.
The only caller poseidon_probe() checks down_firmware flag and
returns 0 without any initialization if it is set.
That looks very strange, so the patch removes down_firmware argument
of check_firmware() and returns error code if check_firmware() fails
in poseidon_probe().
Not tested on real hardware.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All poseidon init functions properly return error codes,
but they are ignored by poseidon_probe(). The patch implements
handling of error cases.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It is not allowed to build driver as a build-in when RC_CORE
(remote controller support) is build as a module.
randconfig build error with next-20130719, in drivers/media/usb
drivers/built-in.o: In function `dvb_usbv2_disconnect':
(.text+0x154b39): undefined reference to `rc_unregister_device'
drivers/built-in.o: In function `dvb_usbv2_init_work':
dvb_usb_core.c:(.text+0x155b2d): undefined reference to `rc_allocate_device'
dvb_usb_core.c:(.text+0x155c38): undefined reference to `rc_register_device'
dvb_usb_core.c:(.text+0x155c5b): undefined reference to `rc_free_device'
drivers/built-in.o: In function `anysee_rc_query':
anysee.c:(.text+0x157795): undefined reference to `rc_keydown'
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The uvcvideo driver lost its dependency on VIDEO_V4L2 during the big
media directory reorganization. Add it back.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If something goes wrong starting from i2c_add_adapter(),
ttusb->iso_urb[] and ttusb itself are not deallocated.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reverse-engineered driver for cheapo video digitizer, made from observations of
Windows XP driver. The protocol is not yet completely understood, so far we
don't provide any controls, only support a single format out of three and don't
support the audio device.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1. usbvision->alt_max_pkt_size is not deallocated anywhere.
2. if allocation of usbvision->alt_max_pkt_size fails,
there is no proper deallocation of already acquired resources.
The patch adds kfree(usbvision->alt_max_pkt_size) to
usbvision_release() as soon as other deallocations happen there.
It calls usbvision_release() if allocation of
usbvision->alt_max_pkt_size fails as soon as usbvision_release()
is safe to work with incompletely initialized usbvision structure.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/usb/pvrusb2/pvrusb2-v4l2.c: In function 'pvr2_v4l2_dev_init':
drivers/media/usb/pvrusb2/pvrusb2-v4l2.c:1268:21: warning: variable 'usbdev' set but not used [-Wunused-but-set-variable]
This warning is due to changeset a28fbd04fa, with removed the
usage of usbdev inside pvr2_v4l2_dev_init().
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mike Isely <isely@pobox.com>
This driver did not yet support struct v4l2_device, so add it. This
make it possible to replace the deprecated parent field with the
v4l2_dev field, allowing the eventual removal of the parent field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function is no longer needed since it is now the responsibility of the
v4l2 core to check if the DBG_G/S_REGISTER and DBG_G_CHIP_INFO ioctls are
called for the bridge driver or not.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* linus: (1465 commits)
ARM: tegra30: clocks: Fix pciex clock registration
lseek(fd, n, SEEK_END) does *not* go to eof - n
Linux 3.10-rc6
smp.h: Use local_irq_{save,restore}() in !SMP version of on_each_cpu().
powerpc: Fix missing/delayed calls to irq_work
powerpc: Fix emulation of illegal instructions on PowerNV platform
powerpc: Fix stack overflow crash in resume_kernel when ftracing
snd_pcm_link(): fix a leak...
use can_lookup() instead of direct checks of ->i_op->lookup
move exit_task_namespaces() outside of exit_notify()
fput: task_work_add() can fail if the caller has passed exit_task_work()
xfs: don't shutdown log recovery on validation errors
xfs: ensure btree root split sets blkno correctly
xfs: fix implicit padding in directory and attr CRC formats
xfs: don't emit v5 superblock warnings on write
mei: me: clear interrupts on the resume path
mei: nfc: fix nfc device freeing
mei: init: Flush scheduled work before resetting the device
sctp: fully initialize sctp_outq in sctp_outq_init
netiucv: Hold rtnl between name allocation and device registration.
...
The GPIO register caching is the result of wrong assumptions and incomplete
knowledge about the GPIO registers and their functionality.
Today, we know that it is not needed.
It is also limited to a single register and therefore incomplete (newer chips
are using multiple registers).
Instead of extending the caching, get rid of it, because it has no real
benefits and just bloats/complicates the code.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- add definition for GPIO register 0x09 (reading/input)
- extend the information the chip variants that support GPIO registers 0x08/0x09
- rename EM28XX_R08_GPIO to EM2820_R08_GPIO_CTRL
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em25xx/em276x/7x/8x provides 4 GPIO register sets,
each of them consisting of separate read and a write registers.
The same registers are also used by the em2874/174/84.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the silly redefines of pr_err/info/debug.
This improves readability and it also gets rid of a bunch of warnings when
compiling this driver for older kernels using the compatibility media_build
system.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media fixes from Mauro Carvalho Chehab:
"Series of fixes for 3.10. There are some usual driver fixes (mostly
on s5p/exynos playform drivers), plus some fixes at V4L2 core"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (40 commits)
[media] soc_camera: error dev remove and v4l2 call
[media] sh_veu: fix the buffer size calculation
[media] sh_veu: keep power supply until the m2m context is released
[media] sh_veu: invoke v4l2_m2m_job_finish() even if a job has been aborted
[media] v4l2-ioctl: don't print the clips list
[media] v4l2-ctrls: V4L2_CTRL_CLASS_FM_RX controls are also valid radio controls
[media] cx88: fix NULL pointer dereference
[media] DocBook/media/v4l: update version number
[media] exynos4-is: Remove "sysreg" clock handling
[media] exynos4-is: Fix reported colorspace at FIMC-IS-ISP subdev
[media] exynos4-is: Ensure fimc-is clocks are not enabled until properly configured
[media] exynos4-is: Prevent NULL pointer dereference when firmware isn't loaded
[media] s5p-mfc: Add NULL check for allocated buffer
[media] s5p-mfc: added missing end-of-lines in debug messages
[media] s5p-mfc: v4l2 controls setup routine moved to initialization code
[media] s5p-mfc: separate encoder parameters for h264 and mpeg4
[media] s5p-mfc: Remove special clock usage in driver
[media] s5p-mfc: Remove unused s5p_mfc_get_decoded_status_v6() function
[media] v4l2: mem2mem: save irq flags correctly
[media] coda: v4l2-compliance fix: add VIDIOC_CREATE_BUFS support
...
As suggested by Antti, this patch replaces:
https://patchwork.kernel.org/patch/2649861/
The buffer overflow is fixed by reading only the r820t ID register.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As USB/PCI/MEDIA_SUPPORT dependencies can be tristate, we can't
simply make the bool menu to be dependent on it. Everything below
the menu should also depend on it, otherwise, we risk to allow
building them with 'y', while only 'm' would be supported.
So, add an IF just before everything below, in order to avoid
such risks.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
current_norm use is deprecated because it is per-devicenode and if you
have more device nodes all dependent on the same video source, then this
no longer works. Just implement g_std instead.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace current_norm by g_std. Also initialize the standard to the more
common NTSC-M format (which is also what current_norm used).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register access to subdevices no longer needs bridge support for those
ioctls. The v4l2 core handles that these days.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mike Isely <isely@isely.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace the V4L2_IDENT_* usage with tveeprom-specific defines. This header
is deprecated, so those defines shouldn't be used anymore.
The em28xx driver is the only one that uses the tveeprom audio_processor
field, so that has been updated to use the new tveeprom AUDPROC define.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove g_chip_ident and replace it with g_chip_info.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove g_chip_ident and replace it with g_chip_info.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_DBG_G_CHIP_IDENT has been replaced by VIDIOC_DBG_G_CHIP_INFO. Remove
g_chip_ident support from bridge drivers since it is no longer needed.
This patch takes care of all the trivial cases.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
get_video_info() should never return EFAULT, instead it should return
the low-level usb_control_msg() error. Add a valid field to the hdpvr_video_info
struct so the driver can easily check if a valid format was detected.
Whenever get_video_info is called and it returns an error (e.g. usb_control_msg
failed), then return that error to userspace as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove an unnecessary 'else' and invert a condition which makes the code
more readable.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If no format has been detected, then querystd should return V4L2_STD_UNKNOWN,
not V4L2_STD_ALL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The device has been tested on a MIPSel box with kernel 3.1.1 and backported media_tree drivers
The kernel detects the device with the following output:
usbcore: registered new interface driver dvb_usb_rtl28xxu
usb 1-2: dvb_usb_v2: found a 'Crypto Redi PC50A' in warm state
usb 1-2: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Crypto Redi PC50A)
usb 1-2: DVB: registering adapter 1 frontend 0 (Realtek RTL2832 (DVB-T))...
i2c i2c-4: fc0012: Fitipower FC0012 successfully identified
usb 1-2: dvb_usb_v2: 'Crypto Redi PC50A' successfully initialized and connected
[crope@iki.fi: fix trivial merge conflict]
Signed-off-by: Alessandro Miceli <angelofsky1980@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
USB ID 0413:6a03 is Leadtek WinFast DTV Dongle mini.
Decoder Realtek RTL2832U and tuner Infineon TUA9001.
Signed-off-by: Miroslav Šustek <sustmidown@centrum.cz>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi,
This patch uses the driver from openpli[1] as a template to restore the remote control support.
I had to divert from the original to use the in kernel rc protocol decoder. The key repetition does,
not seem to work but I cant find the problem in the driver. As a raw rc provider, no key table is
hardcoded.
Rodrigo.
[1]: https://aur.archlinux.org/packages/dvb-usb-rtl2832u-openpli/?comments=all
Signed-off-by: Rodrigo Tartajo <rtarty@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested on a MIPSel box with 3.3.6 kernel
The kernel output when the device will be detected follows:
usbcore: registered new interface driver dvb_usb_it913x
it913x: Chip Version=01 Chip Type=9135
it913x: Remote propriety (raw) mode
it913x: Dual mode=3 Tuner Type=38
it913x: Chip Version=01 Chip Type=9135
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in cold state
usb 2-1: dvb_usb_v2: downloading firmware from file 'dvb-usb-it9137-01.fw'
it913x: FRM Starting Firmware Download
it913x: FRM Firmware Download Completed - Resetting Device
it913x: Chip Version=01 Chip Type=9135
it913x: Firmware Version 204147968
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in warm state
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 1 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_1)...
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 2 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_2)...
usb 2-1: dvb_usb_v2: 'Digital Dual TV Receiver CTVDIGDUAL_V2' successfully initialized and connected
RC part not tested
Signed-off-by: Alessandro Miceli <angelofsky1980@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Maintaining the users count using an atomic variable makes sure that
access to the counter won't be racy, but doesn't serialize access to the
operations protected by the counter. This creates a race condition that
could result in the status URB being submitted multiple times.
Use a mutex to protect the users count and serialize access to the
status start and stop operations.
Reported-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab