Add a helper function to parse the clock names and set up
the bulk data so we can take advantage of the bulk clock
functions instead of rolling our own. This is added
as a helper function so the upcoming a6xx GMU code can
also take advantage of it.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
All users of do_gettimeofday() have been removed, but this one recently
crept in, along with an incorrect printing of the microseconds portion.
This converts it to using ktime_get_real_timespec64() as a direct
replacement, and adds the leading zeroes. I considered using monotonic
times (ktime_get()) instead, but as this timestamp appears to only
be used for humans rather than compared with other timestamps, the
real time domain is probably good enough.
Fixes: e43b045e2c82 ("drm/msm/gpu: Capture the state of the GPU")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For hangs, dump copy out the contents of the buffer objects attached to the
guilty submission and print them in the crash dump report.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add the contents of each ringbuffer to the GPU state and dump the
data in the crash file encoded with ascii85. To save space only
the used portions of the ringbuffer are dumped.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Capture the GPU state on a GPU hang and store it for later playback
via the devcoredump facility. Only one crash state is stored at a
time on the assumption that the first hang is usually the most
interesting. The existing crash state can be cleared after capturing
it and then a new one will be captured on the next hang.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Convert the existing GPU show function to use the GPU state to
dump the information rather than reading it directly from the hardware.
This will require an additional step to capture the state before
dumping it for the existing nodes but it will greatly facilitate reusing
the same code for dumping a previously captured state from a GPU hang.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add the infrastructure to capture the current state of the GPU and
store it in memory so that it can be dumped later.
For now grab the same basic ringbuffer information and registers
that are provided by the debugfs 'gpu' node but obviously this should
be extended to capture a much larger set of GPU information.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add some debugfs to dump out PFP and ME microcontroller state, as well
as some of the queues (MEQ and ROQ). Also add a debugfs file to trigger
a GPU reset (and reloading the firmware on next submit).
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add support for devfreq to dynamically control the GPU frequency.
By default try to use the 'simple_ondemand' governor which can
adjust the frequency based on GPU load.
v2: Fix __aeabi_uldivmod issue from the 0 day bot and use
devfreq_recommended_opp() as suggested by Rob.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Remove the downstream bus scaling code. It isn't needed for for
compatibility with a downstream or vendor kernel. Get it out of the
way to clear space for devfreq support.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We use a global ringbuffer size and block size for all targets and
at least for 5XX preemption we need to know the value the RB_CNTL
in several locations so it makes sense to calculate it once and use
it everywhere.
The only monkey wrench is that we need to disable the RPTR shadow
for A430 targets but that only needs to be done once and doesn't
affect A5XX so we can or in the value at init time.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add the infrastructure to support the idea of multiple ringbuffers.
Assign each ringbuffer an id and use that as an index for the various
ring specific operations.
The biggest delta is to support legacy fences. Each fence gets its own
sequence number but the legacy functions expect to use a unique integer.
To handle this we return a unique identifier for each submission but
map it to a specific ring/sequence under the covers. Newer users use
a dma_fence pointer anyway so they don't care about the actual sequence
ID or ring.
The actual mechanics for multiple ringbuffers are very target specific
so this code just allows for the possibility but still only defines
one ringbuffer for each target family.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
When we move to multiple ringbuffers we're going to store the data
in the memptrs on a per-ring basis. In order to prepare for that
move the current memptrs from the adreno namespace into msm_gpu.
This is way cleaner and immediately lets us kill off some sub
functions so there is much less cost later when we do move to
per-ring structs.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently the behavior of a command stream is provided by the user
application during submission and the application is expected to internally
maintain the settings for each 'context' or 'rendering queue' and specify
the correct ones.
This works okay for simple cases but as applications become more
complex we will want to set context specific flags and do various
permission checks to allow certain contexts to enable additional
privileges.
Add kernel-side submit queues to be analogous to 'contexts' or
'rendering queues' on the application side. Each file descriptor
instance will maintain its own list of queues. Queues cannot be
shared between file descriptors.
For backwards compatibility context id '0' is defined as a default
context specifying no priority and no special flags. This is
intended to be the usual configuration for 99% of applications so
that a garden variety application can function correctly without
creating a queue. Only those applications requiring the specific
benefit of different queues need create one.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that the msm_gem supports an arbitrary number of vma's, we no longer
need to assign an id (index) to each address space. So rip out the
associated code.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The amount of information that we need to pass into msm_gpu_init()
is steadily increasing, so add a new struct to stabilize the function
call and make it easier to add new configuration down the line.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There isn't any generic code that uses ->idle so remove it.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Instead of using a fixed list of clock names use the clock-names
list in the device tree to discover and get the list of clocks
that we need.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some A3XX and A4XX GPU targets required that the GPU clock be
programmed to a non zero value when it was disabled so
27Mhz was chosen as the "invalid" frequency.
Even though newer targets do not have the same clock restrictions
we still write 27Mhz on clock disable and expect the clock subsystem
to round down to zero.
For unknown reasons even though the slow clock speed is always
27Mhz and it isn't actually a functional level the legacy device tree
frequency tables always defined it and then did gymnastics to work
around it.
Instead of playing the same silly games just hard code the "slow" clock
speed in the code as 27MHz and save ourselves a bit of infrastructure.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The adreno code inherited a silly workaround from downstream
from the bad old days before decent clock control. grp_clk[0]
(named 'src_clk') doesn't actually exist - it was used as a proxy
for whatever the core clock actually was (usually 'core_clk').
All targets should be able to correctly request 'core_clk' and
get the right thing back so zap the anachronism and directly
use grp_clk[0] to control the clock rate.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add some new functions to manipulate GPU registers. gpu_read64 and
gpu_write64 can read/write a 64 bit value to two 32 bit registers.
For 4XX and older these are normally perfcounter registers, but
future targets will use 64 bit addressing so there will be many
more spots where a 64 bit read and write are needed.
gpu_rmw() does a read/modify/write on a 32 bit register given a mask
and bits to OR in.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
When the GPU hardware init function fails (like say, ME_INIT timed
out) return error instead of blindly continuing on. This gives us
a small chance of saving the system before it goes boom.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For a5xx the gpu is 64b so we need to change iova to 64b everywhere. On
the display side, iova is still 32b so it can ignore the upper bits.
(Although all the armv8 devices have an iommu that can map 64b pa to 32b
iova.)
Signed-off-by: Rob Clark <robdclark@gmail.com>
We can have various combinations of 64b and 32b address space, ie. 64b
CPU but 32b display and gpu, or 64b CPU and GPU but 32b display. So
best to decouple the device iova's from mmap offset.
Signed-off-by: Rob Clark <robdclark@gmail.com>
At this point, there is nothing left to fail. And submit already has a
fence assigned and is added to the submit_list. Any problems from here
on out are asynchronous (ie. hangcheck/recovery).
Signed-off-by: Rob Clark <robdclark@gmail.com>
Better encapsulate the per-timeline stuff into fence-context. For now
there is just a single fence-context, but eventually we'll also have one
per-CRTC to enable fully explicit fencing.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Track the list of in-flight submits. If the gpu hangs, retire up to an
including the offending submit, and then re-submit the remainder. This
way, for concurrently running piglit tests (for example), one failing
test doesn't cause unrelated tests to fail simply because it's submit
was queued up after one that triggered a hang.
Signed-off-by: Rob Clark <robdclark@gmail.com>
As found in apq8016 (used in DragonBoard 410c) and msm8916.
Note that numerically a306 is actually 307 (since a305c already claimed
306). Nice and confusing.
Signed-off-by: Rob Clark <robdclark@gmail.com>
A few spots in the driver have support for downstream android
CONFIG_MSM_BUS_SCALING. This is mainly to simplify backporting the
driver for various devices which do not have sufficient upstream
kernel support. But the intentionally dead code seems to cause
some confusion. Rename the #define to make this more clear.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Shut down the clks when the gpu has nothing to do. A short inactivity
timer is used to provide a low pass filter for power transitions.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a VRAM carveout that is used for systems which do not have an IOMMU.
The VRAM carveout uses CMA. The arch code must setup a CMA pool for the
device (preferrably in highmem.. a 256m-512m VRAM pool in lowmem is not
cool). The user can configure the VRAM pool size using msm.vram module
param.
Technically, the abstraction of IOMMU behind msm_mmu is not strictly
needed, but it simplifies the GEM code a bit, and will be useful later
when I add support for a2xx devices with GPUMMU, so I decided to keep
this part.
It appears to be possible to configure the GPU to restrict access to
addresses within the VRAM pool, but this is not done yet. So for now
the GPU will refuse to load if there is no sort of mmu. Once address
based limits are supported and tested to confirm that we aren't giving
the GPU access to arbitrary memory, this restriction can be lifted
Signed-off-by: Rob Clark <robdclark@gmail.com>
This got a bit broken with original patches when re-arranging things to
move dependencies on mach-msm inside #ifndef OF.
Signed-off-by: Rob Clark <robdclark@gmail.com>
A basic, no-frills recovery mechanism in case the gpu gets wedged. We
could try to be a bit more fancy and restart the next submit after the
one that got wedged, but for now keep it simple. This is enough to
recover things if, for example, the gpu hangs mid way through a piglit
run.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add initial support for a3xx 3d core.
So far, with hardware that I've seen to date, we can have:
+ zero, one, or two z180 2d cores
+ a3xx or a2xx 3d core, which share a common CP (the firmware
for the CP seems to implement some different PM4 packet types
but the basics of cmdstream submission are the same)
Which means that the eventual complete "class" hierarchy, once
support for all past and present hw is in place, becomes:
+ msm_gpu
+ adreno_gpu
+ a3xx_gpu
+ a2xx_gpu
+ z180_gpu
This commit splits out the parts that will eventually be common
between a2xx/a3xx into adreno_gpu, and the parts that are even
common to z180 into msm_gpu.
Note that there is no cmdstream validation required. All memory access
from the GPU is via IOMMU/MMU. So as long as you don't map silly things
to the GPU, there isn't much damage that the GPU can do.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Jordan Crouse