Commit Graph

361 Commits

Author SHA1 Message Date
Peter Ujfalusi ffd950f75d ASoC: davinci-mcasp: Add support for I2S format
The FS needs to be inverted in McASP compared to other supported formats.
Use a flag to indicate if the FS needs to be inverted.
At the same time fail when non supported format is asked since the default
case was anyways configuring McASP to a not valid format.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-04-14 17:24:24 +01:00
Peter Ujfalusi 83f12503bd ASoC: davinci-mcasp: Move the FS polarity change out from the switch case
FS polarity can be either rising or falling edge in McASP. Instead of
accessing the registers in every switch/case set a flag and write the
registers after the switch for the invert configuration.
This change will help when adding support for more formats also.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-04-14 17:24:24 +01:00
Peter Ujfalusi 188edc59c2 ASoC: davinci-mcasp: Support for DSP_A format
DSP_A is like DSP_B mode but with one bit delay after the FS.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-04-14 17:24:24 +01:00
Peter Ujfalusi 6dfa9a4e6a ASoC: davinci-mcasp: Format data delay configuration enhancement
Use intermediate variable for the data delay needed for the specific format
and write the register after the format configuration at once.
This will help to control the number of lines as support for more formats
going to be added.
Also fixes a case when we switch between two formats with different delay
requirements.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-04-14 17:24:24 +01:00
Peter Ujfalusi 33445643c3 ASoC: davinci-mcasp: Fine tune and correct the DMA burst configuration
When the AFIFO is not enabled but more than one serializers are used the DMA
need to transfer number of words equal to active serializers when a DMA
request is generated.
When configuring the burst for the DMA avoid using value '1' for the burst
since it is going to enable additional logic in the DMA drivers. Burst '1'
means that the DMA should send/receive one word per DMA requests.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-04-14 17:24:11 +01:00
Peter Ujfalusi dd093a0f19 ASoC: davinic-mcasp: Adopt the AFIFO/DMA configuration to the stream (dynamic depth)
Configure the AFIFO numevt parameter based on the requested tx/rx_numevt,
active serializers and period size in words.
In this way McASP can adopt it's (and the DMA) configuration runtime and
can pick the most optimal setup which satisfy the parameters.
This way we do not need to place any constraint on the stream itself,
allowing application greater freedom on how they want to set up ALSA.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-04-14 17:24:11 +01:00
Peter Ujfalusi 5f04c603a5 ASoC: davinci-mcasp: Configure the AFIFO and DMA burst size at the same place
Move the dma_params->fifo_level and dma_data->maxburst configuration to the
mcasp_common_hw_param() function where we configure the AFIFO registers.
It makes the code regarding to AFIFO and DMA configuration more easy to
follow since it is now clear how the AFIFO and how the DMA is going to be
configured.
Previously this has been done in two functions using a bit different
calculation form - which ended up with the same result in both case at the
end, but it was confusing.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-04-14 17:24:11 +01:00
Peter Ujfalusi 0bf0e8aece ASoC: davinci-mcasp: Simplify and clean up the AFIFO configuration code
We can have more linear code flow by using variables in
mcasp_common_hw_param() related to the AFIFO configuration.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-04-14 17:24:11 +01:00
Peter Ujfalusi f5b02b4a2c ASoC: davinci-mcasp: Fix debug typo in davinci_mcasp_hw_params()
requred -> required

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-04-14 17:24:11 +01:00
Peter Ujfalusi d5902f6936 ASoC: davinci-mcasp: Assign the dma_data earlier in dai_probe callback
Set up the playback_dma_data/capture_dma_data for the dai at probe
time since the generic dmaengine PCM stack needs to have access to
this information early.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-04-14 17:24:10 +01:00
Peter Ujfalusi 1a95d8d09e ASoC: davinci-pcm: Add empty functions for !CONFIG_SND_DAVINCI_SOC builds
To save drivers using davinci-pcm and edma-pcm the need to fiddle with
!CONFIG_SND_DAVINCI_SOC in their code.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-04-14 17:24:10 +01:00
Peter Ujfalusi 74ddd8c40d ASoC: davinci-mcasp: Fix bit clock polarity settings
IB_NF, NB_IF and IB_IF configured the bc polarity incorrectly. The receive
polarity was set to the same edge as the TX in these cases.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-04-08 12:56:45 +01:00
Peter Ujfalusi 8de131f2e6 ASoC: davinci-mcasp: Provide correct filter_data for dmaengine for non-DT boot
When we boot with non-DT mode the damengine will need the channel number and
a filter function in order to get the channel.
The filter_data is filled in the DAI driver while the filter_function will
be provided by the edma-pcm driver.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-17 16:21:36 +00:00
Peter Ujfalusi 58726f58a6 ASoC: davinci: Add edma dmaengine platform driver
Platform driver glue for SoC using eDMA3 to use dmaengine PCM.
The maximum number of periods need to be limited to 19 since the
edma dmaengine driver limits the paRAM slot use for audio at
in cyclic mode.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-17 16:21:06 +00:00
Lars-Peter Clausen d343a660d3 ASoC: davinci-evm: Register machine level DAPM elements with the card
Machine level DAPM widgets and routes should be registered in the card's DAPM
context, rather than in the CODEC's context.

While we are at it also drop the snd_soc_dapm_enable_pin() calls, since pins are
enabled by default and also turn the snd_soc_dapm_disable_pin() calls into
snd_soc_dapm_nc_pin() calls for unconnected pins.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-13 19:11:19 +00:00
Peter Ujfalusi 64ebdec36a ASoC: davinci-mcasp: Rename the pointer to davinci dma_params as dma_params
It is quite confusing to name the pointer to davinci_pcm_dma_params as
dma_data. Rename the pointer to avoid confusion.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-09 08:33:53 +00:00
Peter Ujfalusi 790bb94b56 ASoC: davinci-mcasp: Remove long lines from suspend/resume callbacks
Move the context register storage behind of a struct and use a pointer to
it in the suspend/resume callbacks to remove the long lines.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-03 18:26:59 +00:00
Peter Ujfalusi d1debafc38 ASoC: davinci-mcasp: Rename platform data struct
Rename the struct for the platform data:
snd_platform_data -> davinci_mcasp_pdata

Since we have users under arch/arm/mach-davinci/ for this struct add
temporary define to avoid breakage. The arch code can be updated later to
use the new struct name.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-03 18:26:59 +00:00
Peter Ujfalusi a7e46bd9a1 ASoC: davinci-mcasp: Code cleanup in davinci_mcasp_hw_params()
Rearrange the code in the function for readability.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-03 18:26:59 +00:00
Peter Ujfalusi 135014adc6 ASoC: davinci-mcasp: Move pm callbacks from platform device to soc_dai_driver
Handle the PM callbacks via the ASoC core instead of device core.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-31 16:38:28 +00:00
Peter Ujfalusi 0f7d9a635b ASoC: davinci-mcasp: Return value handling cleanup for mcasp_common_hw_param()
Take the return value from mcasp_common_hw_param() and use that in case of
error.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-31 16:38:24 +00:00
Mark Brown 61d384aed4 Merge branch 'fix/davinci' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into HEAD 2014-01-31 16:38:20 +00:00
Peter Ujfalusi fb6d208d54 ASoC: davinci-evm: Add pm callbacks to platform driver
Set snd_soc_pm_ops for the pm ops.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-31 16:21:24 +00:00
Peter Ujfalusi 1d17a04ef2 ASoC: davinci-mcasp: Consolidate pm_runtime_get/put() use in the driver
The use of pm_runtime in trigger() callback is not correct and it will lead
to unbalanced power.usage_count.
The only place which might need to call pm_runtime is the set_fmt callback.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-31 16:19:19 +00:00
Peter Ujfalusi 2c56c4c27c ASoC: davinci-mcasp: Configure xxTDM, xxFMT and xxFMCT registers synchronously
These registers can be configured synchronously for playback and capture.
Furthermore when McASP is in master and sync mode the capture operation
needs the TX path to be configured in order to be able to provide the needed
clocks for the bus.
xxFMT and xxFMCT registers has been already configured for both TX and RX
other places in the driver.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-31 15:51:20 +00:00
Peter Ujfalusi 662ffae9ed ASoC: davinci-mcasp: Harmonize the sub hw_params function names
Instead of
davinci_hw_common_param - for common, I2S/DIT mode settings
davinci_hw_dit_param - for DIT protocol configuration
davinci_hw_param - for I2S (and compatible protocols)

Use the following names:
mcasp_common_hw_param, mcasp_dit_hw_param and mcasp_i2s_hw_param.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-31 15:51:20 +00:00
Jyri Sarha ab8b14b6d8 ASoC: davinci-mcasp: Set BCLK divider if McASP is BCLK master
Make BCLK divider setting implicite in hw_params call if McASP device
is the bit clock master on the audio serial bus.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-27 20:45:57 +00:00
Jyri Sarha 5ad8865b00 ASoC: davinci-evm: Add named clock reference to DT bindings
The referenced clock is used to get codec clock rate and the clock is
disabled and enabled in startup and shutdown snd_soc_ops call
backs. The change is also documented in DT bindigs document.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
cc: bcousson@baylibre.com
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-27 18:09:40 +00:00
Lars-Peter Clausen f52c919215 ASoC: davinci: Don't set unused struct snd_pcm_hardware fields
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-24 12:01:17 +00:00
Peter Ujfalusi ae726e9394 ASoC: davinci-mcasp: Support for fck reparenting
Optional DT property to specify the desired parent clock for the McASP fck
clock.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:25 +00:00
Peter Ujfalusi b14899da9d ASoC: davinci-mcasp: Correct am33xx snd_platform_data name
An earlier patch overlooked this when the compatible has been changed from
omap2 -> am33x.
Rename omap2_mcasp_pdata to am33xx_mcasp_pdata.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:17 +00:00
Peter Ujfalusi f68205a7f8 ASoC: davinci-mcasp: Change IO functions parameter list
Instead of passing __iomem address (mcasp->base + register_offset) pass
the main mcasp structure and only access the mcasp->base in the low level
IO functions.
In most cases this helps with code readability and it will make it easier
to switch over to regmap in the future.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:16 +00:00
Peter Ujfalusi 453c499028 ASoC: davinci-mcasp: Support for McASP version found in DRA7xx
The IP in DRA7xx is similar to the IP found in TI81xxAM3xxx/AM4xxx type of
SoCs but it is is integrated with sDMA instead of eDMA. The suitable pcm
driver for DRA7xx is the omap-pcm driver which is using dmaengine.
In the driver we can configure both dma related structures used for eDMA and
sDMA. The only thing we need to make sure that we set the correct dma_data
at startup with snd_soc_dai_set_dma_data()

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:16 +00:00
Peter Ujfalusi 4dcb5a0bff ASoC: davinci-mcasp: Fix synchronous master receive mode
In synchronous mode both transmit and receive sections are using the TX
clocks. In setup like this the TX clocks need to be enabled when capture
is running.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:16 +00:00
Peter Ujfalusi cbc7956c81 ASoC: davinci-mcasp: Data source (bus) selection support
The audio data to/from McASP can be sent/received via two method:
Via the data port (preferred) or via the configuration bus.
Currently the driver assumes that all data communication will be done via
the data port.
This patch adds support for selecting the configuration port as data
interface.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:16 +00:00
Peter Ujfalusi 487dce8823 ASoC: davinci-mcasp: Simplify FIFO configuration code
The FIFO registers base address is different in dm646x compared to newer
SoCs with McASP IP. Instead of using two paths (switch/case) to handle the
difference we can simply pick the correct base address beforehand and use
offsets to address the register we need to configure.
With this change the indentation depth can be reduced as well.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:16 +00:00
Peter Ujfalusi 8f113b77b5 ASoC: davinci-mcasp: Be consistent with the use of base in davinci_mcasp_set_dai_fmt
Replace mcasp->base use with plain base in the davinci_mcasp_set_dai_fmt()
function since it has been already used by the remaining part of the function.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:16 +00:00
Peter Ujfalusi 70091a3e6a ASoC: davinci-mcasp: Rename private struct and it's users (dev -> mcasp)
Rename the private struct from davinci_audio_dev to davinci_mcasp.
Change the local use of the pointer to this struct from *dev to *mcasp.

The aim is to have better readable code for the first look since having
dev->xxxx in the code when using the local private struct is a bit
surprising.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:16 +00:00
Peter Ujfalusi eba0ecf067 ASoC: davinci-mcasp: Do not inline the mcasp_set_ctl_reg function
It brings no benefit to inline this function due to it's size and function.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:16 +00:00
Peter Ujfalusi 57f439b867 ASoC: davinci-mcasp: Remove unused DAVINCI_MCASP_NUM_SERIALIZER define
It is not used in the code.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:16 +00:00
Peter Ujfalusi 21400a72d6 ASoC: davinci-mcasp: Move private struct definition to source file
Since it is a private struct strictly used by the davinci-mcasp driver it
can be moved from header file to the source file.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:15 +00:00
Peter Ujfalusi 02e08d9b6b ASoC: davinci-mcasp: Move register definitions to header file
It is better for readability to have the register definitions out from the
source file.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:15 +00:00
Peter Ujfalusi 58e48d9774 ASoC: davinci-mcasp: Correct dai driver struct initialization for 2nd dai
Add .name when assigning the dai name.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:15 +00:00
Peter Ujfalusi 18f9350662 ASoC: davinci-mcasp: Remove unused DAVINCI_MCASP_I2S/DIT_DAI defines
These are not used, probably leftovers from the past.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:15 +00:00
Peter Ujfalusi ed29cd5e8d ASoC: davinci-mcasp: Move DAVINCI_MCASP_RATE from header to source file
It is not used outside of the .c file.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:15 +00:00
Peter Ujfalusi d38970e136 ASoC: davinci-evm: Switch to use .dai_fmt of snd_soc_dai_link(s)
Specify the dai formats to use within the snd_soc_dai_link structures. In
this way we can remove the code dealing with the dai format configuration
from the machin driver.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:15 +00:00
Peter Ujfalusi 7b6a772932 ASoC: davinci-evm: Do not include davinci-mcasp.h
There's no need to include this header file here.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:15 +00:00
Peter Ujfalusi a42efd97f7 ASoC: davinci: kconfig: Prepare for AM43xx support
AM43xx have the same McASP IP as AM33xx and both platform uses eDMA. Modify
the Kconfig so it will be possible to add audio support for AM43xx based
boards later.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:15 +00:00
Peter Ujfalusi c3238a4c05 ASoC: davinci: Kconfig/Makefile: Generic EVM machine driver related cleanup
We have several boards using the same machine driver for audio support.
All of these machines can select a generic machine driver config option to
build the needed driver while keeping the config options used within the
driver for compile time code path selection.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:15 +00:00
Peter Ujfalusi 860d0c0dd2 ASoC: davinci: Kconfig: Remove help section for SND_DAVINCI_SOC
The help text is misleading and the prompt itself explains the purpose of
this config section.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-10 11:22:14 +00:00
Linus Torvalds e6d69a60b7 Merge branch 'next' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine changes from Vinod Koul:
 "This brings for slave dmaengine:

   - Change dma notification flag to DMA_COMPLETE from DMA_SUCCESS as
     dmaengine can only transfer and not verify validaty of dma
     transfers

   - Bunch of fixes across drivers:

      - cppi41 driver fixes from Daniel

      - 8 channel freescale dma engine support and updated bindings from
        Hongbo

      - msx-dma fixes and cleanup by Markus

   - DMAengine updates from Dan:

      - Bartlomiej and Dan finalized a rework of the dma address unmap
        implementation.

      - In the course of testing 1/ a collection of enhancements to
        dmatest fell out.  Notably basic performance statistics, and
        fixed / enhanced test control through new module parameters
        'run', 'wait', 'noverify', and 'verbose'.  Thanks to Andriy and
        Linus [Walleij] for their review.

      - Testing the raid related corner cases of 1/ triggered bugs in
        the recently added 16-source operation support in the ioatdma
        driver.

      - Some minor fixes / cleanups to mv_xor and ioatdma"

* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (99 commits)
  dma: mv_xor: Fix mis-usage of mmio 'base' and 'high_base' registers
  dma: mv_xor: Remove unneeded NULL address check
  ioat: fix ioat3_irq_reinit
  ioat: kill msix_single_vector support
  raid6test: add new corner case for ioatdma driver
  ioatdma: clean up sed pool kmem_cache
  ioatdma: fix selection of 16 vs 8 source path
  ioatdma: fix sed pool selection
  ioatdma: Fix bug in selftest after removal of DMA_MEMSET.
  dmatest: verbose mode
  dmatest: convert to dmaengine_unmap_data
  dmatest: add a 'wait' parameter
  dmatest: add basic performance metrics
  dmatest: add support for skipping verification and random data setup
  dmatest: use pseudo random numbers
  dmatest: support xor-only, or pq-only channels in tests
  dmatest: restore ability to start test at module load and init
  dmatest: cleanup redundant "dmatest: " prefixes
  dmatest: replace stored results mechanism, with uniform messages
  Revert "dmatest: append verify result to results"
  ...
2013-11-20 13:20:24 -08:00
Linus Torvalds 8ceafbfa91 Merge branch 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm
Pull DMA mask updates from Russell King:
 "This series cleans up the handling of DMA masks in a lot of drivers,
  fixing some bugs as we go.

  Some of the more serious errors include:
   - drivers which only set their coherent DMA mask if the attempt to
     set the streaming mask fails.
   - drivers which test for a NULL dma mask pointer, and then set the
     dma mask pointer to a location in their module .data section -
     which will cause problems if the module is reloaded.

  To counter these, I have introduced two helper functions:
   - dma_set_mask_and_coherent() takes care of setting both the
     streaming and coherent masks at the same time, with the correct
     error handling as specified by the API.
   - dma_coerce_mask_and_coherent() which resolves the problem of
     drivers forcefully setting DMA masks.  This is more a marker for
     future work to further clean these locations up - the code which
     creates the devices really should be initialising these, but to fix
     that in one go along with this change could potentially be very
     disruptive.

  The last thing this series does is prise away some of Linux's addition
  to "DMA addresses are physical addresses and RAM always starts at
  zero".  We have ARM LPAE systems where all system memory is above 4GB
  physical, hence having DMA masks interpreted by (eg) the block layers
  as describing physical addresses in the range 0..DMAMASK fails on
  these platforms.  Santosh Shilimkar addresses this in this series; the
  patches were copied to the appropriate people multiple times but were
  ignored.

  Fixing this also gets rid of some ARM weirdness in the setup of the
  max*pfn variables, and brings ARM into line with every other Linux
  architecture as far as those go"

* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
  ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
  ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
  ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
  ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
  ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
  ARM: DMA-API: better handing of DMA masks for coherent allocations
  ARM: 7857/1: dma: imx-sdma: setup dma mask
  DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
  DMA-API: dcdbas: update DMA mask handing
  DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
  DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
  DMA-API: crypto: remove last references to 'static struct device *dev'
  DMA-API: crypto: fix ixp4xx crypto platform device support
  DMA-API: others: use dma_set_coherent_mask()
  DMA-API: staging: use dma_set_coherent_mask()
  DMA-API: usb: use new dma_coerce_mask_and_coherent()
  DMA-API: usb: use dma_set_coherent_mask()
  DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
  DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
  DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
  ...
2013-11-14 07:55:21 +09:00
Nicolin Chen 1112b9e2c9 sound/soc/davinci/davinci-pcm.c: use gen_pool_dma_alloc() in davinci-pcm.c
Since gen_pool_dma_alloc() is introduced, we implement it to simplify code.

Signed-off-by: Nicolin Chen <b42378@freescale.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-11-13 12:09:23 +09:00
Sebastian Andrzej Siewior 262093791b fix missing edma changes to EDMA_DMA_COMPLETE status
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2013-11-12 10:12:52 +05:30
Russell King c9bd5e690a DMA-API: sound: fix dma mask handling in a lot of drivers
This code sequence is unsafe in modules:

static u64 mask = DMA_BIT_MASK(something);
...
	if (!dev->dma_mask)
		dev->dma_mask = &mask;

as if a module is reloaded, the mask will be pointing at the original
module's mask address, and this can lead to oopses.  Moreover, they
all follow this with:

	if (!dev->coherent_dma_mask)
		dev->coherent_dma_mask = mask;

where 'mask' is the same value as the statically defined mask, and this
bypasses the architecture's check on whether the DMA mask is possible.

Fix these issues by using the new dma_coerce_coherent_and_mask()
function.

Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2013-10-31 14:48:47 +00:00
Hebbar, Gururaja ee2f615d6e ASoC: davinci-evm: Add device tree binding
Device tree support for Davinci Machine driver

When the board boots with device tree, the driver will receive card,
codec, dai interface details (like the card name, DAPM routing map,
phandle for the audio components described in the dts file, codec mclk
speed). The card will be set up based on this information. Since the
routing is provided via DT we can mark the card fully routed so core
can take care of disconnecting the unused pins.

Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-10-23 16:43:07 +01:00
Hebbar, Gururaja d79e07c95d ASoC: davinci: Add support for AM33xx SoC Audio
AM33xx uses same McASP IP as the Davinci Platform. This patch updates
Kconfig and makefile to enable build for McASP, PCM & Codec drivers.

Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-10-23 16:39:33 +01:00
Peter Ujfalusi 1427e660b4 ASoC: davinci-mcasp: Remove redundant num-serializer DT parameter
The serial-dir array gives this information so there is no need to have the
num-serializer property in DT description.
Just ignore the property in the driver the DTS files can be updated
separately without regression.
Update the documentation at the same time for davinci-mcasp

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-10-23 12:15:03 +01:00
Jyri Sarha 3af9e03156 ASoC: davinci-mcasp: Change compatible property model to more accurate
Change the model omap2-mcasp-audio in compatible property to
am33xx-mcasp-audio as omap2 does not have mcasp.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-10-22 12:03:21 +01:00
Jyri Sarha 4023fe6ff2 ASoC: davinci-mcasp: Extract DMA channels directly from DT
Extract DMA channels directly from DT as they can not be found from
platform resources anymore. This is a work-around until davinci audio
driver is updated to use dmaengine.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-10-22 12:03:21 +01:00
Jyri Sarha 256ba181cb ASoC: davinci-mcasp: Add location for data port registers to DT
This patch adds a separate register location for data port registers to
mcasp DT bindings. On am33xx SoCs the McASP registers are mapped
trough L4 interconnect, but data port registers are also mapped trough
L3 bus to a different memory location.

Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-10-22 12:03:21 +01:00
Daniel Mack a85e419ede ASoC: davinci-mcasp: add support for suspend and resume
When the system returns from suspend, it looses its configuration. Most
of it is restored by running a normal audio stream startup, but the DAI
format is left unset as that's configured on the audio device creation.

Hence, it suffices here to care for the registers which are touched by
davinci_mcasp_set_dai_fmt() and restore them when the system is resumed.

Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-10-03 14:22:40 +01:00
Jyri Sarha bcf25567ec ASoC: davinci-evm: Move sysclk logic away from evm_hw_params
The sysclk rate does not change runtime so it should be initialized at
init time.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-09-18 10:53:24 +01:00
Linus Torvalds 1286da8bc0 sound updates for 3.11
A relative calm release at this time with a flat diffstat.
 The only significant change in the ALSA core side is the support for
 more than 32 card instances, configurable via kconfig.
 Other than that, in both ASoC and other parts, mostly some
 improvements and fixes on the driver side.
 
 - hda: More quirks for ALC269-variants on Dell & co, VIA codec fixes
 - hda: Haswell HDMI audio fixes, runtime PM improvements
 - hda: Intel BayTrail support, ALC5505 DSP support
 - es1968: MediaForte M56VAP support
 - usb-audio: Improved support for Yamaha/Roland devices
 - usb-audio: M2Tech hiFace, Audio Advantage Micro II support
 - hdspm: wordclock fixes
 - ASoC: Pending fixes for WM8962
 - ASoC: Cleanups and fixes for Blackfin, SGTL5000 and UX500
 - ASoC: Generalisation of the Bluetooth and HDMI stub drivers
 - ASoC: SSM2518 and RT5640 codec drivers.
 - ASoC: Tegra CPUs with RT5640 machine driver
 - ASoC: AC'97 refactoring bug fixes
 - ASoC: ADAU1701 driver fixes
 - Clean up of *_set_drvdata() in a wide range of drivers
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iQIcBAABAgAGBQJR1BNeAAoJEGwxgFQ9KSmk5mAP/iH8IPdaMq/EI3Kdk2lwqXwK
 xQvpQCKTeux4UrETSDM5kOfk+Nv0oq7jD60wEZs6eONAZdfIzACEjdpQBdC4vr6f
 2S8b9J6xBe2siHGbzBsgV9g8xhnYXC5m0u8QBRa9fyNVpMu1o1X6Mv7FS/wUCMZ6
 M7vaSdrU4pfa4v9sy9loOYbyDZoSZg0revwqWAm8Kfp4XSd1aPwiCVPLVOWcvNYC
 hriz5ICARFg+yqzJADPBYtSU752zxlZd/N1b2YQw1YnoxA66FoVaqQfYD1voL0WY
 8m9abNlnln6qxyeQPMvRMZty1I/kCwOlp5dO0OZHisMLE8MApLk1e7ct9+W+b9hn
 NORbo3klmwZfIl1s8JSGHs5Nknqzhdzau35TVPTmtC50wgnPO6EYVeYFiZqkuYyK
 UdCHJTRjyS6HlmbdKeSaRr+PoCR0zVQruXFjWnAwQ9Zy+1qrnVb5Ly9np7YCc8YC
 3iYOygJyn+JmyfeeIxVUCg6Rdf4NUv+JPx48yuoq79YnWAbRiSSct1/J+4YcYcm5
 VjJdtCwElil3dSeba+Oy2wcSwaJzyaINbClzmZdysT26M8QLZaRCBU0zujeiyl/n
 lV/p/n+UmmtfHIdJDz6Eu6fQVAbh0v89mZrEJdjroLebwS1NBLAaKkb9vY63AdKt
 P5c/7KWejQ/CtoVYeo3O
 =i5lT
 -----END PGP SIGNATURE-----

Merge tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound

Pull sound updates from Takashi Iwai:
 "A relative calm release at this time with a flat diffstat.  The only
  significant change in the ALSA core side is the support for more than
  32 card instances, configurable via kconfig.  Other than that, in both
  ASoC and other parts, mostly some improvements and fixes on the driver
  side.

   - hda: More quirks for ALC269-variants on Dell & co, VIA codec fixes
   - hda: Haswell HDMI audio fixes, runtime PM improvements
   - hda: Intel BayTrail support, ALC5505 DSP support
   - es1968: MediaForte M56VAP support
   - usb-audio: Improved support for Yamaha/Roland devices
   - usb-audio: M2Tech hiFace, Audio Advantage Micro II support
   - hdspm: wordclock fixes
   - ASoC: Pending fixes for WM8962
   - ASoC: Cleanups and fixes for Blackfin, SGTL5000 and UX500
   - ASoC: Generalisation of the Bluetooth and HDMI stub drivers
   - ASoC: SSM2518 and RT5640 codec drivers.
   - ASoC: Tegra CPUs with RT5640 machine driver
   - ASoC: AC'97 refactoring bug fixes
   - ASoC: ADAU1701 driver fixes
   - Clean up of *_set_drvdata() in a wide range of drivers"

* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (284 commits)
  ALSA: vmaster: Fix the regression of missing vmaster hook call
  ALSA: hda - Add Dell SSID to support Headset Mic recording
  ASoC: adau1701: remove control_data assignment
  ASoC: adau1701: more direct regmap usage
  ASoC: ac97: fixup multi-platform AC'97 module build failure
  ASoC: pxa2xx: fixup multi-platform AC'97 build failures
  ASoC: tegra20-ac97: Remove unused variable
  ASoC: tegra20-ac97: Remove duplicate error message
  ALSA: usb-audio: Add Audio Advantage Micro II
  ASoC: tas5086: fix Mid-Z implementation
  ASoC: tas5086: fix TAS5086_CLOCK_CONTROL register size
  ALSA: Replace the magic number 44 with const
  ALSA: hda - Fix the max length of control name in generic parser
  ALSA: hda - Guess what, it's two more Dell headset mic quirks
  ALSA: hda - Yet another Dell headset mic quirk
  ALSA: hda - Add support for ALC5505 DSP power-save mode
  ASoC: mfld: Remove unused variable
  ALSA: usb-audio: add quirks for Roland QUAD/OCTO-CAPTURE
  ALSA: usb-audio: claim autodetected PCM interfaces all at once
  ALSA: usb-audio: remove superfluous Roland quirks
  ...
2013-07-03 19:52:22 -07:00
Matt Porter 3ad7a42d5a ARM: davinci: move private EDMA API to arm/common
Move mach-davinci/dma.c to common/edma.c so it can be used
by OMAP (specifically AM33xx) as well.

Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Chris Ball <cjb@laptop.org> # davinci_mmc.c
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
[nsekhar@ti.com: dropped davinci sffsdr changes]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2013-06-18 10:52:03 +05:30
Mark Brown 684d8c515c Merge remote-tracking branch 'asoc/topic/davinci' into asoc-next 2013-06-17 17:20:18 +01:00
Sekhar Nori 4867e99d21 ASoC: davinci: remove sffsdr machine support
sffsdr machine support does not build since at least v2.6.36
(~3 years). There is little hope of it being fixed, so remove
the support.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-06-17 09:59:31 +01:00
Sachin Kamat ea421eb18d ASoC: davinci: Remove redundant use of of_match_ptr macro
'mcasp_dt_ids' is always compiled in. Hence of_match_ptr is not
necessary.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
2013-06-03 16:46:05 +01:00
Daniel Mack 7967189251 ASoC: davinci: fix sample rotation
McASP serial audio engine needs different rotation values on TX and RX
channels. Commit dde109fb46 ("ASoC: McASP: Fix data rotation for
playback. Enables 24bit audio playback") changed the calculation to fix
the playback format, but broke the capture stream by doing it for both
TXFMT and RXFMT.

Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org [3.9 only]
2013-05-21 13:21:09 -05:00
Lars-Peter Clausen cde11aedea ASoC: davinci-sffsdr: Staticize non exported struct
The pcm3008_codec struct is not used outside of davinci-sffsdr.c, so make it
static.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-05-15 08:54:14 +04:00
Takashi Iwai f91eeeb595 ASoC: Updates for v3.10
A few more bug fixes, the DAPM clock fix is actually a driver specific
 one since currently there's only one user of the clock support due to
 the problems relying on the clock API.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJRg3/MAAoJELSic+t+oim9W+cP/3NERwICTNvllNOrZXii7akJ
 DnzzIaw0fEJ2+hIXJzU/lEI/KjqIT7SADQRWg+eid8ZrjaUB6LXUPPuv67V4TseD
 1+8ClQp1cDg1KepBcD2S1liVjPKvW64IpXwZNgLGigW6PP21yK8+DoQvVKPVB+sP
 q72jntTzy9qWenmjygpPEYDeOfe5EM7hAaa2tFuYIPEL+EkMOXXvjx8ojylwQV6V
 5xFQ+CBSS8WHz7CKlawF3JH8TkcFGZNT9Hibhv1fpGM+iJDCsh/+MNiBwOpO+1wk
 eCJSiCWWTGgVK+3AvlSIQr8ml0EDEbS8Aq6bbJb9w4wgV65oFt2hOxOpkcK/8NcP
 qnKNYc3nRQsb3H+dObMdQNPWDjOfwsolKUOjetxosRIq4Pzm8afY96gu06EqTnw9
 XYXqoSAVpCuPDpmlu87Lajoj4T5XNq3G7ONAMpsAfMrl/xxmV11Wrs4/7S0o3Csb
 tNhO5XjLbFNTw9nVT6qZQViH7Bm1ItDM2B/tLb1yqnlgBAjNW/WlUyFg4bE4Qeyr
 hUg7DwvYPSVnr25t8RmPMmB2MdD4N+PfRy+aIEIuE9KMeYUTPVr5kFdDP7uA7Yw2
 Dn7lmAdDEq33zfTGYhGWs87IdxhD3VyEWveR6alrtBW0LS7ArtsPlWKhA074XuJj
 AmAU6RS3+75nymA9ucY+
 =WQzu
 -----END PGP SIGNATURE-----

Merge tag 'asoc-v3.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next

ASoC: Updates for v3.10

A few more bug fixes, the DAPM clock fix is actually a driver specific
one since currently there's only one user of the clock support due to
the problems relying on the clock API.
2013-05-03 11:39:36 +02:00
Marek Belisko df4a4eece7 ASoC: McASP: Fix receive clock polarity in DAIFMT_NB_NF mode.
According documentation bit ACLKRPOL is set to 0 (receiver samples data
on falling edge) and when set to 1 (receiver samples data on rising edge).

I2S data are always sampled on falling edge and valid during rising edge
of bit clock. So in case of capture data transmitter sample data on falling
edge and macsp must read then on rising edge.

Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-05-03 09:29:59 +01:00
Marek Belisko 81ee6833bc ASoC: McASP: Add pins output direction for rx clocks when configured in CBS_CFS format
When McASP is bit clock and frame clock master enable pin output for rx clocks.

Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-04-30 19:44:23 +01:00
Michal Bachraty d486fea6ba ASoC: davinci-mcasp: Add Support BCLK-to-LRCLK ratio for TDM modes
For TDM mode, BCLK-to-LCLK ratio is computed as (tdm_slots) x (word_length).
I2S mode is only subset of TDM mode with specific tdm_slots = 2 channels.
Also bclk_lrclk_ratio can be greater than 255, therefore u16 need to be used.

Signed-off-by: Michal Bachraty <michal.bachraty@streamunlimited.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-04-23 14:50:30 +01:00
Michal Bachraty 7c21a78104 ASoC: davinci-pcm, davinci-mcasp: Clean up active_serializers
As pointed of by Vaibhav, commit message: "ASoC: davinci-mcasp: Add support for multichannel playback"
number of active serializers can be hidden into fifo_level variable, which is set in davimci-mcasp.

Signed-off-by: Michal Bachraty <michal.bachraty@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-04-23 14:50:21 +01:00
Mark Brown d66e065c5b Merge remote-tracking branch 'asoc/topic/davinci' into asoc-next 2013-04-12 13:57:03 +01:00
Yegor Yefremov f5023af65a ASoC: davinci-mcasp: don't overwrite DIT settings
Channel size settings will be made at the end of
davinci_mcasp_hw_params() routine and thus overwrite frame
format settings made for DIT mode. This patch fixes this issue
by taking op_mode into account. Tested with official PSP 3.2
kernel and sii9022a HDMI transmitter.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-04-05 11:27:13 +01:00
Yegor Yefremov 2dda75e07d ASoC: davinci-mcasp: don't configure AFSX direction in DIT mode
AFSX won't be used in DIT mode. The related pins are AHCLKX and
the data pins.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-04-05 11:27:09 +01:00
Kuninori Morimoto eeef0eda7a ASoC: switch over to use snd_soc_register_component() on davinci mcasp
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-03-26 21:55:22 +00:00
Kuninori Morimoto ee226ce195 ASoC: switch over to use snd_soc_register_component() on davinci vcif
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-03-26 21:55:22 +00:00
Kuninori Morimoto bfcb921caf ASoC: switch over to use snd_soc_register_component() on davinci i2s
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-03-26 21:55:21 +00:00
Daniel Mack ecf327c7ca ASoC: davinci-mcasp: clean up davinci_hw_common_param()
As pointed of by Vaibhav, commit 2952b27e2 ("ASoC: davinci-mcasp:
Add support for multichannel playback") duplicated the logic of
counting the active serializers. That can be avoided by shifting
the code around a bit.

Also, drop two unused defines introduced by the same commit.

Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-03-12 19:03:53 +00:00
Michal Bachraty 2952b27e2e ASoC: davinci-mcasp: Add support for multichannel playback
Davinci McASP has support for I2S multichannel playback.
For I2S playback/receive, each serializer is capable to play 2 channels
(L/R) audio data.Serializer function (Playback-receive-none) is configured
in DT, depending on hardware specification. It is possible to play less
channels than configured in DT. For that purpose,only specific number of
active serializers are enabled. McASP FIFO need to have DMA transfer Bcnt
set to number of enabled serializers, otherwise no data are transfered to
McASP and Alsa generates "DMA/IRQ playback write error (DMA or IRQ trouble?)"
error. For TDM mode, McASP is capable to play or receive 32 channels for one
serializer. McAsp has support for max 16 serializer, therefore max channels
is 32 * 8.

Signed-off-by: Michal Bachraty <michal.bachraty@streamunlimited.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-03-04 11:09:13 +08:00
Mark Brown 315472d5ab Merge remote-tracking branch 'asoc/topic/tlv320aic3x' into asoc-next 2013-02-11 11:06:46 +00:00
Hebbar Gururaja e2e8bfdf61 ASoC: tlv320aic3x: Convert mic bias to a supply widget
Convert MicBias widgets to supply widget.

On tlv320aic3x, Mic bias power on/off shares the same register bits
with output mic bias voltage.  So, when power on mic bias, we need
reclaim it to voltage value.

Provide a new platform data so that the micbias voltage can be sent
according to board requirement. Now since tlv320aic3x codec driver
is DT aware, update dt files and functions to handle this new
"micbias-vg"  platform data.

Because of sharing of bits, when enabling the micbias, voltage also
needs to be updated. So use SND_SOC_DAPM_POST_PMU & SND_SOC_DAPM_PRE_PMD
macro to create an event to handle this.

Since micbias is converted to supply widget, updated machine drivers as
well.

This change is runtime tested on da850-evm with audio loopback
(arecord|aplay) for confirmation.

Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-02-04 18:35:19 +00:00
Michal Bachraty dde109fb46 ASoC: McASP: Fix data rotation for playback. Enables 24bit audio playback
u32 rotate = (32 - word_length) / 4;
This implementation is wrong, but it works only for 16, or 32 bit audio data.
(rotation for 16 or 32 bit is same as in code I present) Mcasp rotated data in
4 bits (max value 0x7)and then masks them . That data are sended to i2s bus.
For 24 bit or 20 bit or other data formats, this code rotates data badly and
you hear somethink like noise.  You need to use
u32 rotate = (word_length / 4) & 0x7;
to proper data rotation.

Signed-off-by: Michal Bachraty <michal.bachraty@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-27 14:14:46 +08:00
Daniel Mack 1b3bc060fb ASoC: McASP: implement a way to force BCLK/LRCLK ratios
Depending on the Codec, the the BCLK/LRCLK ratio might not be freely
chosen by the CPU DAI.

For example, some Codec might want to be supplied with 32-bit samples
for both its channels regardless of the actual audio word size the CPU
sends. In such cases, the rest of the bits on the data lines must be
padded with zeros:

          _______________________________
LRCLK    /                               \
      --'                                 `---------- .....

BCLK  ||||||||||||||||||||||||||||||||||||||||||||||| .....

DATA  ____||||||||||||||||_________________|||||||||| .....

          |<--  data  -->|<--   pads  --> |

This patch adds a new clock divider to configure the BCLK/LRCLK ratio.
If the machine code uses that divider, the driver uses the specified
value, instead of deriving that information from the audio word size.

Otherwise, the original behaviour is retained.

Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-12-07 14:47:10 +09:00
Daniel Mack ba764b3def ASoC: McASP: calculate values for channel size
Change davinci_config_channel_size() to derive the values for XSSZ and
XROT in DAVINCI_MCASP_[RT]XFMT_REG from the configured word length
rather than hard-coding them in a switch/case block.

Also, by directly passing the word length to
davinci_config_channel_size(), we can get rid of the
DAVINCI_AUDIO_WORD_* enum.

Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-12-07 14:47:01 +09:00
Daniel Mack d0c6c482f6 ASoC: McASP: remove unused variables
codec_fmt and sample_rate variables are unused in both snd_platform_data
and davinci_audio_dev, so drop them.

Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-12-07 14:46:56 +09:00
Matt Porter b8ec56d8ea ASoC: davinci: replace private sram api with genalloc
Removes the DaVinci private SRAM API and replaces it with
the genalloc API. The SRAM gen_pool is passed in pdata since
DaVinci is in the early stages of DT conversion.

[zonque@gmail.com: stub out gen_pool functions for
		   !CONFIG_GENERIC_ALLOCATOR]

Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-22 14:58:34 +01:00
Daniel Mack 6b7fa01157 ASoC: McASP: treat SNDRV_PCM_FORMAT_U24_* as 32 bit words
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-15 11:24:48 +09:00
Daniel Mack 21eb24d8d5 ASoC: McASP: add support for 24 bit samples
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-15 11:24:48 +09:00
Daniel Mack 5296cf2d5e ASoC: McASP: set format parameters in dependence of the DAI format
The FSDUR flag configures whether the frame clock uses a high phase of
only one bit or a full word. This has to be set depending on the DAI
format.

For other modes than DSP_B, the FSXDLY/FSRDLY fields have to be set to
1.

Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-15 11:24:47 +09:00
Daniel Mack 5b66aa2d0c ASoC: McASP: make AHCLK direction configurable
Add a .set_sysclk function to pass the direction of the clock down to
the driver. Only enable AHCLKX in the PDIR register when the CPU is
driving the clock.

This also removes the modification of the AHCLKXE/AHCLKRE bits in the
hw_params callback, and users must set the desired configuration using
snd_soc_dai_set_sysclk(), which this patch also does for the only user
in mainline (davinci-evm).

Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-15 11:24:47 +09:00
Daniel Mack 4ed8c9b737 ASoC: McASP: add support for clock dividers
Add support for the internal clock dividers of the McASP driver.

Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-15 11:24:47 +09:00
Daniel Mack 393a53cbcf ASoC: enable 192KHz support for McASP
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-15 11:24:29 +09:00
Hebbar, Gururaja e5ec69da24 ASoC: Davinci: McASP: add support new McASP IP Variant
The OMAP2+ variant of McASP is different from Davinci variant w.r.to
some register offset.

Changes
- Add new MCASP_VERSION_3 to identify new variant. New DT compatible
  "ti,omap2-mcasp-audio" to identify version 3 controller.
- The register offsets are handled depending on the version.

Note:
    DMA parameters (dma fifo offset) are not updated and will be done later.

Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-06 08:20:33 +08:00
Mark Brown 75d8f2931a Merge branch 'asoc-omap' into for-3.7 2012-09-05 20:05:11 +08:00
Hebbar, Gururaja ffb690d5aa ASoC: Davinci: evm: Fix typo in cpu dai name
Fix typo caused by recent commit (cf53756 - ASoC: davinci: davinci-pcm
does not need to be a plaform_driver)

Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-31 17:47:19 -07:00
Hebbar, Gururaja 3e3b8c3415 ASoC: Davinci: McASP: add device tree support for McASP
Add device tree probe for McASP driver.

Note:
DMA parameters are not populated from DT and will be done later.

Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-27 11:12:09 -07:00
Hebbar, Gururaja 896f66b7de ASoC/ARM: Davinci: McASP: split asp header into platform and audio specific
Davinci McASP header & driver are shared by few OMAP platforms (like
TI81xx, AM335x). Splitting asp header into Davinci platform specific
header and Audio specific header helps to share them across platforms.

Audio specific defines is moved to to common
<linux/platform_data/davinci_asp.h> so that the header can be
accessed by all related platforms.

While here, correct the header usage (remove multiple header
re-definitions and unused headers) and remove platform names from
structures comments and enum. Also some some coding style errors.

Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Acked-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-27 11:12:09 -07:00
Hebbar, Gururaja f08095a408 ASoC: davinci: davinci-pcm does not need to be a plaform_driver
Same as the commit 518de86 (ASoC: tegra: register 'platform' from DAIs,
get rid of pdev). It makes davinci-pcm not a platform_driver but helper
to register "platform", so that the platform_device for davinci-pcm can
be saved completely.

Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-27 11:12:08 -07:00
Hebbar, Gururaja 10884347f1 ASoC: McASP: Convert driver to use Runtime PM API
* Add Runtime PM support to McASP host controller.
  * Use Runtime PM API to enable/disable McASP clock.

This was tested on AM18x Board using suspend/resume

Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-09 14:06:10 +01:00
Hebbar, Gururaja 8f24549979 ASoC: Davinci: McASP: remove unused header include
Defines or parameters from <mach/mux.h> isn't used anywhere. Hence
remove the header include.

Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-09 14:06:10 +01:00
Vaibhav Bedia 0d62427572 ASoC: Davinci: McASP: Flush the FIFO before enabling
FIFO should be flushed before it is enabled for the first time.
This fixes the I/O errors reported by the ASoC core on a fresh boot

Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-09 14:05:47 +01:00
Joachim Eastwood 350e16d529 ASoC: replace 0xffffffff with DMA_BIT_MASK macro
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-01-20 13:58:26 +00:00
Joachim Eastwood 25e9e7565f ASoC: check for substream not channels_min in pcm engines
This is a follow up on 53dea36c70 which fixes the other affected
pcm engines.

Description from 53dea36c70c1857:
 Don't rely on the codec's channels_min information to decide wheter or
 not allocate a substream's DMA buffer. Rather check if the substream
 itself was allocated previously.

Without this patch I was seeing null-pointer dereferenc in atmel-pcm.

Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-01-07 11:18:05 -08:00
Julia Lawall cd0ff7eff0 ASoC: davinci-i2s.c: use devm_ functions
The various devm_ functions allocate memory that is released when a driver
detaches.  This patch uses devm_kzalloc, devm_request_mem_region and
devm_ioremap for data that is allocated in the probe function of a platform
device and is only freed in the remove function.

In this case, the original code did not contain a call to iounmap, nor does
one appear anywhere else in the file.  I have assumed that it is safe to
use devm_ioremap for the allocation in any case.

Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-01-02 13:07:56 +00:00
Julia Lawall 96d31e2b12 ASoC: davinci-mcasp.c: use devm_ functions
The various devm_ functions allocate memory that is released when a driver
detaches.  This patch uses devm_kzalloc, devm_request_mem_region and
devm_ioremap for data that is allocated in the probe function of a platform
device and is only freed in the remove function.

In this case, the original code did not contain a call to iounmap, nor does
one appear anywhere else in the file.  I have assumed that it is safe to
use devm_ioremap for the allocation in any case.

Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-01-02 13:07:51 +00:00
Julia Lawall a3bb8f3f81 ASoC: davinci-vcif.c: use devm_ functions
The various devm_ functions allocate memory that is released when a driver
detaches.  This patch uses devm_kzalloc, devm_request_mem_region and
devm_ioremap for data that is allocated in the probe function of a platform
device and is only freed in the remove function.

Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-01-02 13:07:46 +00:00
Axel Lin 36a16d1ae0 ASoC: davinci: Add .owner to struct snd_soc_card
Missed .owner of struct snd_soc_card will prevent the module from being
removed from underneath its users.

Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-12-22 17:34:34 +00:00
Axel Lin f9b8a51493 ASoC: Convert davinci directory to module_platform_driver
Factor out some boilerplate code.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-25 13:15:31 +00:00
Lars-Peter Clausen 85e7652d89 ASoC: Constify snd_soc_dai_ops structs
Commit 1ee46ebd("ASoC: Make the DAI ops constant in the DAI structure")
introduced the possibility to have constant DAI ops structures, yet this is
barley used in both existing drivers and also new drivers being submitted,
although none of them modifies its DAI ops structure. The later is not
surprising since existing drivers are often used as templates for new drivers.
So this patch just constifies all existing snd_soc_dai_ops structs to eliminate
the issue altogether.

The patch was generated with the following coccinelle semantic patch:
// <smpl>
@@
identifier ops;
@@
-struct snd_soc_dai_ops ops =
+const struct snd_soc_dai_ops ops =
{ ... };
// </smpl>

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-11-23 10:40:46 +00:00
Linus Torvalds 68d99b2c8e Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits)
  ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
  ALSA: hda - Keep EAPD turned on for old Conexant chips
  ALSA: hda/realtek - Fix missing volume controls with ALC260
  ASoC: wm8940: Properly set codec->dapm.bias_level
  ALSA: hda - Fix pin-config for ASUS W90V
  ALSA: hda - Fix surround/CLFE headphone and speaker pins order
  ALSA: hda - Fix typo
  ALSA: Update the sound git tree URL
  ALSA: HDA: Add new revision for ALC662
  ASoC: max98095: Convert codec->hw_write to snd_soc_write
  ASoC: keep pointer to resource so it can be freed
  ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls
  ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2
  ASoC: da7210: Add support for line out and DAC
  ASoC: da7210: Add support for DAPM
  ALSA: hda/realtek - Fix DAC assignments of multiple speakers
  ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value
  ASoC: Set sgtl5000->ldo in ldo_regulator_register
  ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture
  ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture
  ...
2011-10-28 14:25:01 -07:00
Paul Bolle 6760235fa4 Drop default from "DM365 codec select" choice
SND_DM365_EXTERNAL_CODEC does not exist, so it's a useless default.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-10-13 18:19:31 +02:00
Mark Brown 87bea31c7b ASoC: Remove redundant snd_soc_dapm_sync() calls from machine drivers
The core will sync DAPM as part of the card initialization, there is no
need for machine drivers to do so during their setup.

OMAP drivers are omitted as I know Peter already has patches for them.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-10-08 14:10:54 +01:00
Jarkko Nikula ad51f76544 ASoC: Davinci: Fix FS polarity for I2S format
Commit 75d9ac4 ("ASoC: Allow DAI formats to be specified in the dai_link")
changed DAI format flag values and we cannot simply invert anymore e.g.
frame-sync with ^= SND_SOC_DAIFMT_NB_IF (which was anyway misuse) as there
is no anymore fixed bit position for bit-clock or frame-sync inversion.

Fix this by relying only on DAI format flag values passed to us and by not
making any assumption on individual bit positions

Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Vaibhav Bedia <vaibhav.bedia@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-09-30 11:56:56 +01:00
Ben Gardiner be4ff96122 ASoC: davinci-pcm: trivial: replace link with actual chan/link
The ambiguously named variable 'link' is used as a temporary throughout
davinci-pcm -- its presence makes grepping (and groking) the code
difficult.

Replace link with the value of link in almost all sites. The exception
is a couple places where the last-assigned link/chan needs to be
returned by a function -- in these cases, rename to last_link.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-09-16 10:12:47 +01:00
Ben Gardiner 0a9d138528 ASoC: davinci-mcasp: add support for unsigned PCM formats
Although the McASP supports sign-extending samples in RX or TX [1]; the
davinci-mcasp driver does not touch the {R,X}PBIT or {R,X}PAD field of the
{R,X}FMT registers meaning that the McASP will serialize the bytes it is given
regardless of their signedness. So supporting unsigned formats is as simple
as adding them to the metadata of the davinci-mcasp driver.

Update the FMTBITs reported in the snd_soc_dai_driver and also update the case
statements in davinci-mcasp's hw_params() function so that the McASP can be
connected to CODECs that use unsigned values.

[1] http://www.ti.com/lit/ug/sprufm1/sprufm1.pdf

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-08-29 10:11:17 +01:00
Rajashekhara, Sudhakar 82d1d52103 ASoC: davinci: add missing break statement
In davinci_vcif_trigger() function, a break() statement was missing
causing the davinci_vcif_stop() function to be called as a fallback
after calling davinci_vcif_start().

Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
2011-07-20 20:51:35 +01:00
Rajashekhara, Sudhakar 3012f43eaf ASoC: davinci: fix codec start and stop functions
According to DM365 voice codec data sheet at [1], before starting
recording or playback, ADC/DAC modules should follow a reset and
enable cycle. Writing a 1 to the ADC/DAC bit in the register resets
the module and clearing the bit to 0 will enable the module. But the
driver seems to be doing the reverse of it.

[1] http://focus.ti.com/lit/ug/sprufi9b/sprufi9b.pdf

Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
2011-07-20 20:51:23 +01:00
Liam Girdwood 552d1ef6b5 ASoC: core - Optimise and refactor pcm_new() to pass only rtd
Currently pcm_new() passes in 3 arguments :- card, pcm and DAI.

Refactor this to only pass in 1 argument (i.e. the rtd) since struct rtd contains
card, pcm and DAI along with other members too that are useful too.

Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-06-07 18:38:27 +01:00
Mark Brown aa72f6899b Merge branch 'for-3.0' into for-3.1 2011-06-06 12:26:02 +01:00
Mark Brown d21685ec25 Merge branch 'for-2.6.40' into for-2.6.41 2011-05-30 10:54:18 +08:00
Samuel Ortiz cb5811cf32 mfd: Use mfd cell platform_data for davinci cells platform bits
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.

Cc: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-05-26 19:45:13 +02:00
Ben Gardiner bb5b5fd4d4 ASoC: davinci-pcm: comments for the conversion to BATCH mode
In the previous commit 'ASoC: davinci-pcm: convert to BATCH mode', the phase
offset of 2 was mentioned in the commit message but not well commented in the
source.

Add descriptive comments of the phase offset with and without ping-pong
buffers enabled.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-05-25 22:59:07 +08:00
Ben Gardiner 52e2c5d38e ASoC: davinci-pcm: convert to BATCH mode
The davinci-pcm driver's snd_pcm_ops pointer function currently calls into
the edma controller driver to read the current positions of the edma channels
to determine pos to return to the ALSA framework. In particular,
davinci_pcm_pointer() calls edma_get_position() and the latter has a comment
indicating that "Its channel should not be active when this is called" whereas
the channel is surely active when snd_pcm_ops.pointer is called.

The operation of davinci-pcm in capture and playback appears to follow close
the other pcm drivers who export SNDRV_PCM_INFO_BATCH except that davinci-pcm
does not report it's positions from pointer() using the last transferred
chunk. Instead it peeks directly into the edma controller to determine the
current position as discussed above.

Convert the davinci-pcm driver to BATCH mode: count the periods elapsed in the
prtd->period member and use its value to report the 'pos' to the alsa
framework in the davinci_pcm_pointer function.

There is a phase offset of 2 periods between the position used by dma setup
and the position reported in the pointer function. Either +2 in the dma
setup or -2 in the pointer function (with wrapping, both) accounts for this
offset -- I opted for the latter since it makes the first-time setup clearer.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Steven Faludi <stevenfaludi@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-05-25 19:14:31 +08:00
Ben Gardiner 10ab3bfda4 ASoC: davinci-pcm: extract period elapsed functions
Extract functions that modify the prtd->period member in preparation for
conversion to BATCH mode playback.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Steven Faludi <stevenfaludi@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-05-25 19:14:31 +08:00
Ben Gardiner ef39eb6f21 ASoC: davinci-pcm: fix audible glitch on 2nd ping-pong playback
The release of the dma channels was being performed in prepare and there was a
edma_resume call for the asp-channel only being executed on START, RESUME and
PAUSE_RELEASE.

The mcasp on da850evm with ping-pong buffers enabled was exhibiting an audible
glitch on every playback after the first. It was determined through trial and
error that the following two changes fix this problem:

1) Move the edma_start calls from prepare to trigger and 2) reverse the order
of starting the asp and ram channels.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Steven Faludi <stevenfaludi@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-05-25 19:14:30 +08:00
Ben Gardiner acb8e2666e ASoC: davinci-pcm: increase the maximum channels
Based on the registration of davinci-mcasp.1 in the davinci-evm platform
setup for da830 and dm6467, davinci-pcm can handle more than the currently
reported maximum channels of 2.

Increase the maximum channels to 384 to match the maximum reported by
davinci-mcasp.1.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Steven Faludi <stevenfaludi@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-05-25 19:14:29 +08:00
Ben Gardiner 8e56d5b834 ASoC: davinci-pcm: expand the .formats
Based on the data_type test in ping_pong_dma_setup, davinci-pcm is capable of
handling data of width up to and including 32bits.

"
	if ((data_type == 0) || (data_type > 4)) {
		printk(KERN_ERR "%s: data_type=%i\n", __func__, data_type);
		return -EINVAL;
	}
"

Update the .format member of the snd_pcm_hardware instances it registers to
reflect this capability.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Steven Faludi <stevenfaludi@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-05-25 19:14:29 +08:00
Ben Gardiner fb1e9703af ASoC: davinci-pcm: trivial: make ping-pong params setup symmetrical
The setup of the pong channel uses EDMA_CHAN_SLOT instead of & 0x3f as the
setup of the ping channel does.

Make the setup of ping and pong symmetric. There is no functional change
introduced by this patch.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Steven Faludi <stevenfaludi@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-05-25 19:14:28 +08:00
Ben Gardiner a0c8326397 ASoC: davinci-mcasp: enable ping-pong SRAM buffers
The davinci-i2s driver copies the platform data for playback and capture
sram sizes which is in turn used by davinci-pcm to allocate ping-pong
buffers.

Copy also the platform data in davinci-mcasp probe.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-05-19 14:11:17 -07:00
Ben Gardiner db92f43745 davinci-mcasp: fix _CBM_CFS pin directions
The current davinci_mcasp_set_dai_fmt() sets bits ACLKX and ACLKR in the PDIR
register for the codec clock-master/frame-slave mode; however, this results in
the ACLKX and ACLKR pins being outputs according to SPRUFM1 [1]  which
conflicts with "codec is clock master."

Similarly to the previous patch in this series, "fix _CBM_CFS hw_params" --
For codec clock-master/frame-slave mode (_CMB_CFS), clear bits ACLKX and ACLKR
in the PDIR register to set the pins as inputs and hence allow externally
sourced bit-clocks.

[1] http://www.ti.com/litv/pdf/sprufm1

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: James Nuss <jamesnuss@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-04-26 11:43:53 +01:00
Ben Gardiner a90f549e25 davinci-mcasp: fix _CBM_CFS hw_params
The current davinci_mcasp_set_dai_fmt() sets bits ACLKXE and ACLKRE (CLKXM
and CLKRM as they are reffered to in SPRUFM1 [1]) for codec clock-slave/
frame-slave mode (_CBS_CFS) which selects internally generated bit-clock and
frame-sync signals; however, it does the same thing again for codec
clock-master/frame-slave mode (_CBM_CFS) in the very next case statement which
is incorrectly selecting internally generated bit-clocks in this mode.

For codec clock-master/frame-slave mode (_CBM_CFS), clear bits ACLKXE and
ACLKRE to select externally-generated bit-clocks.

[1] http://www.ti.com/litv/pdf/sprufm1

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: James Nuss <jamesnuss@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-04-26 11:43:38 +01:00
Ben Gardiner 9595c8f035 davinci-mcasp: use bitfield definitions for PDIR
The current driver creates value for set/clr of PDIR using (x<<26) instead
of the #defines that are convieniently made available.

Update the driver to use the bitfield definitions of PDIR. There is no
functional change introduced by this patch.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: James Nuss <jamesnuss@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-04-26 11:43:29 +01:00
Ben Gardiner 049cfaaa47 ASoC: davinci-mcasp: correct tdm_slots limit
The current check for the number of tdm-slots specified by platform data is
always true (x >= 2 || x <= 32); therefore the else branch that warns of an
incorrect number of slots can never be taken.

Check that the number of tdm slots specified by platform data is between 2
and 32, inclusive.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: James Nuss <jamesnuss@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-04-26 11:43:19 +01:00
Andres Salomon d57763370e asoc: davinci_voicecodec: use mfd_data instead of driver_data
Use mfd_data for passing information from mfd drivers to soc
clients.  The mfd_cell's driver_data field is being phased out.

Clients that were using driver_data now access .mfd_data
via mfd_get_data().

Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-03-23 10:41:56 +01:00
Vaibhav Bedia 4f82f02852 ASoC: Davinci: Replace usage of IO_ADDRESS with ioremap()
This patch modifies the Davinci i2s and mcasp drivers to make use of
ioremap() instead of IO_ADDRESS()

Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-02-09 22:33:32 +00:00
Vaibhav Bedia eef6d7b8c2 ASoC: Davinci: Call clk_disable() and clk_put() in case of error
In case of any error in probe() function, clk_disable() and clk_put()
should be called if clk_enable() and clk_get() went through.

Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-02-09 22:33:16 +00:00
Vaibhav Bedia d852f446b7 ASoC: Davinci: Use resource_size() helper function
This patch modifies the Davinci i2s and mcasp drivers
to make use of the resource_size() helper function for readability.

Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-02-09 22:33:03 +00:00
Vaibhav Bedia f9eb9dd14c asoc: davinci: da830/omap-l137: correct cpu_dai_name
McASP1 is used on the DA830/OMAP-L137 platform for the codec.
This is different from the DA850/OMAP-L138 platform which uses McASP0.

This is fixed by adding a new snd_soc_dai_link struct.

Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-02-03 20:16:09 +00:00
Rajashekhara, Sudhakar dc5a460a1b ASoC: da8xx/omap-l1xx: match codec_name with i2c ids
The codec_name entry for da8xx evm in sound/soc/davinci/davinci-evm.c
is not matching with the i2c ids in the board file. Without this fix the
soundcard does not get detected on da850/omap-l138/am18x evm.

Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Tested-by: Dan Sharon <dansharon@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37)
2011-01-21 18:19:56 +00:00
Jarkko Nikula 5e79d64b03 ASoC: Remove needless inclusion of tlv320aic3x.h from machine drivers
After multi-component conversion these machine drivers don't actually need
anything from sound/soc/codecs/tlv320aic3x.h so don't include it.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2011-01-05 11:28:50 +00:00
Mark Brown 2c54c1586c Merge branch 'for-2.6.37' into for-2.6.38 2010-11-25 11:17:24 +00:00
Axel Lin 8b6b30ab66 ASoC: davinci-vcif - fix a memory leak
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-11-25 11:12:34 +00:00
Jarkko Nikula 505fb824e7 ASoC: Do not include soc-dapm.h
There is no need to include soc-dapm.h since soc.h includes it.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-11-22 14:04:41 +00:00
Mark Brown 3df94756fe Merge branch 'for-2.6.37' into for-2.6.38 2010-11-17 18:59:19 +00:00
Chris Paulson-Ellis bedad0ca3f ASoC: davinci: fixes for multi-component
Multi-component commit f0fba2ad broke a few things which this patch should
fix. Tested on the DM355 EVM. I've been as careful as I can, but it would be
good if those with access to other Davinci boards could test.

--

The multi-component commit put the initialisation of
snd_soc_dai.[capture|playback]_dma_data into snd_soc_dai_ops.hw_params of the
McBSP, McASP & VCIF drivers (davinci-i2s.c, davinci-mcasp.c & davinci-vcif.c).
The initialisation had to be moved from the probe function in these drivers
because davinci_*_dai changed from snd_soc_dai to snd_soc_dai_driver.

Unfortunately, the DMA params pointer is needed by davinci_pcm_open (in
davinci-pcm.c) before hw_params is called. I have moved the initialisation to
a new snd_soc_dai_ops.startup function in each of these drivers. This fix
indicates that all platforms that use davinci-pcm must have been broken and
need to test with this fix.

--

The multi-component commit also changed the McBSP driver name from
"davinci-asp" to "davinci-i2s" in davinci-i2s.c without updating the board
level references to the driver name. This change is understandable, as there
is a similarly named "davinci-mcasp" driver in davinci-mcasp.c.

There is probably no 'correct' name for this driver. The DM6446 datasheet
calls it the "ASP" and describes it as a "specialised McBSP". The DM355
datasheet calls it the "ASP" and describes it as a "specialised ASP". The
DM365 datasheet calls it the "McBSP". Rather than fix this problem by
reverting to "davinci-asp", I've elected to avoid future confusion with the
"davinci-mcasp" driver by changing it to "davinci-mcbsp", which is also
consistent with the names of the functions in the driver. There are other
fixes required, so it was never going to be as simple as a revert anyway.

--

The DM365 only has one McBSP port (of the McBSP platforms, only the DM355 has
2 ports), so I've changed the the id of the platform_device from 0 to -1.

--

In davinci-evm.c, the DM6446 EVM can no longer share a snd_soc_dai_link
structure with the DM355 EVM as they use different cpu DAI names (the DM355
has 2 ports and the EVM uses the second port, but the DM6446 only has 1 port).
This also means that the 2 boards need different snd_soc_card structures.

--

The codec_name entries in davinci-evm.c didn't match the i2c ids in the board
files. I have only checked and fixed the details of the names used for the
McBSP based platforms. Someone with a McASP based platform (eg DA8xx) should
check the others.

Signed-off-by: Chris Paulson-Ellis <chris@edesix.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-11-17 18:36:40 +00:00
Liam Girdwood ce6120cca2 ASoC: Decouple DAPM from CODECs
Decoupling Dynamic Audio Power Management (DAPM) from codec devices is
required when developing ASoC further. Such as for other ASoC components to
have DAPM widgets or when extending DAPM to handle cross-device paths.

This patch decouples DAPM related variables from struct snd_soc_codec and
moves them to new struct snd_soc_dapm_context that is used to encapsulate
DAPM context of a device. ASoC core and API of DAPM functions are modified
to use DAPM context instead of codec.

This patch does not change current functionality and a large part of changes
come because of structure and internal API changes.

Core implementation is from Liam Girdwood <lrg@slimlogic.co.uk> with some
minor core changes, codecs and machine driver conversions from
Jarkko Nikula <jhnikula@gmail.com>.

Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Cc: Timur Tabi <timur@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jassi Brar <jassi.brar@samsung.com>
Cc: Daniel Gloeckner <dg@emlix.com>
Cc: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-11-06 11:28:29 -04:00