Use list_for_each_entry_safe() instead of explicit cast to avoid relying on
struct layout
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During parity errors, the ramrods are not issued to FW. bnx2fc waits for the
timeout value, and proceeds with cleaning up the IOs. Since we are already
out-of-sync with FW, cleanup commands timeout too, and do not get the
completion. This operation takes 36 secs for each session to upload causing
huge delays. To fix this, bnx2fc now gets a PARITY_ERROR from cnic driver, and
upon failure, the driver does not issue any commands to the FW and finishes the
upload process sooner.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We do not hold the host lock when calling these functions,
so remove comment.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This has scsi_internal_device_unblock/scsi_target_unblock take
the new state to set the devices as an argument instead of
always setting to running. The patch also converts users of these
functions.
This allows the FC and iSCSI class to transition devices from blocked
to transport-offline, so that when fast_io_fail/replacement_timeout
has fired we do not set the devices back to running. Instead, we
set them to SDEV_TRANSPORT_OFFLINE.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds a new state SDEV_TRANSPORT_OFFLINE. It will
be used by transport classes to offline devices for cases like
when the fast_io_fail/recovery_tmo fires. In those cases we
want all IO to fail, and we have not yet escalated to dev_loss_tmo
behavior where we are removing the devices.
Currently to handle this state, transport classes are setting
the scsi_device's state to running, setting their internal
session/port structs state to something that indicates failed,
and then failing IO from some transport check in the queuecommand.
The reason for the new value is so that users can distinguish
between a device failure that is a result of a transport problem
vs the wide range of errors that devices get offlined for
when a scsi command times out and we offline the devices there.
It also fixes the confusion as to why the transport class is
failing IO, but has set the device state from blocked to running.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Recent changes to add fcoe_sysfs caused libfcoe_init to call fcoe_transport_exit
in a module initialization routine. The change resulted in the below error. This
patch removes the __exit keyword from the fcoe_transport_exit definition such
that it may be called from an __init routine.
WARNING: drivers/scsi/fcoe/libfcoe.o(.init.text+0x21): Section mismatch in reference from the function init_module() to the function .exit.text:fcoe_transp
exit()
The function __init init_module() references
a function __exit fcoe_transport_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __exit annotation of
fcoe_transport_exit() so it may be used outside an exit section.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
bnx2fc had an assumption that the fcoe interface will always start on the vlan
dev. However, some switch implementations (Eg., HP virtual connect FlexFabric)
expects the fcoe interface to be started on physical interface. Do not error
out if the netdev is not a vlan dev.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Deduplication of formats and consolidating tests
makes the object much smaller.
Add bnx2fc_debug.c, add functions for a few logging
functions (BNX2FC_IO_DBG, BNX2FC_TGT_DBG, BNX2FC_HBA_DBG).
Use printf extension %pV.
Add and use pr_fmt and pr_<level>.
Move the debug #include below structure definitions.
$ size drivers/scsi/bnx2fc/built-in.o*
text data bss dec hex filename
101563 1165 24976 127704 1f2d8 drivers/scsi/bnx2fc/built-in.o.new
138473 1109 33400 172982 2a3b6 drivers/scsi/bnx2fc/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since bnx2fc_percpu_thread_create() creates percpu kthread, it makes
sense to use kthread_create_on_node() to get proper NUMA affinity for
kthread stack.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
scsi_wait_scan was introduced with asynchronous host scanning as a hack
for distributions that weren't using proper udev based wait for root to
appear in their initramfs scripts. In 2.6.30 Commit
c751085943
Author: Rafael J. Wysocki <rjw@sisk.pl>
Date: Sun Apr 12 20:06:56 2009 +0200
PM/Hibernate: Wait for SCSI devices scan to complete during resume
Actually broke scsi_wait_scan because it renders
scsi_complete_async_scans() a nop for modular SCSI if you include
scsi_scans.h (which this module does).
The lack of bug reports is sufficient proof that this module is no
longer used.
Cc: Jeff Mahoney <jeffm@suse.de>
Cc: Dave Jones <davej@redhat.com>
Cc: maximilian attems <max@stro.at>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Updates newly added stats from fc_get_host_stats,
added new function fc_exch_update_stats to
update exches related stats from fc_exch.c
by going thru internal ema_list elements.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Adds stats to track FCP pkt and frame alloc
failure.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The libfc is used by fcoe but fcoe agnostic,
and therefore should not have any fcoe references.
So renaming fcoe_dev_stats from libfc as its for fc_stats.
After that libfc is fcoe string free except some strings for
Open-FCoE.org.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The libfc provides more flexibility and with that
we can monitor some more FC specific stats for
FC exches or FCP error cases, this patch add
such new FC stats.
The patch adds *only* FC specific new stats to
existing fc_host attribute container.
Added stats names are self explanatory as
existing FC stats already has, however anyway
still added commentary along their definition
to describe them.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull last minute Ceph fixes from Sage Weil:
"The important one fixes a bug in the socket failure handling behavior
that was turned up in some recent failure injection testing. The
other two are minor bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: endian bug in rbd_req_cb()
rbd: Fix ceph_snap_context size calculation
libceph: fix messenger retry
One of the bugs was introduced in 3.5-rc1. Others have
been there for longer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=zpJG
-----END PGP SIGNATURE-----
Merge tag 'md-3.5-fixes' of git://neil.brown.name/md
Pull three md bugfixes from NeilBrown:
"One of the bugs was introduced in 3.5-rc1. Others have been there for
longer."
* tag 'md-3.5-fixes' of git://neil.brown.name/md:
md/raid1: close some possible races on write errors during resync
md: avoid crash when stopping md array races with closing other open fds.
md: fix bug in handling of new_data_offset
Pull HID update from Jiri Kosina:
"A final round of changes for HID for 3.5: just device ID additions."
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hid-multitouch: add support for Zytronic panels
HID: add Sennheiser BTD500USB device support
HID: add battery quirk for Apple Wireless ANSI
The strcpy was being used to set the name of the board. Since the
destination char* was read-only and the name is set statically at
compile time; this was both wrong and redundant.
The type of char* is changed to const char* to prevent future errors.
Reported-by: Radek Masin <radek@masin.eu>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
[ Taking directly due to vacations - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 4367af5561
md/raid1: clear bad-block record when write succeeds.
Added a 'reschedule_retry' call possibility at the end of
end_sync_write, but didn't add matching code at the end of
sync_request_write. So if the writes complete very quickly, or
scheduling makes it seem that way, then we can miss rescheduling
the request and the resync could hang.
Also commit 73d5c38a95
md: avoid races when stopping resync.
Fix a race condition in this same code in end_sync_write but didn't
make the change in sync_request_write.
This patch updates sync_request_write to fix both of those.
Patch is suitable for 3.1 and later kernels.
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Original-version-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
md will refuse to stop an array if any other fd (or mounted fs) is
using it.
When any fs is unmounted of when the last open fd is closed all
pending IO will be flushed (e.g. sync_blockdev call in __blkdev_put)
so there will be no pending IO to worry about when the array is
stopped.
However in order to send the STOP_ARRAY ioctl to stop the array one
must first get and open fd on the block device.
If some fd is being used to write to the block device and it is closed
after mdadm open the block device, but before mdadm issues the
STOP_ARRAY ioctl, then there will be no last-close on the md device so
__blkdev_put will not call sync_blockdev.
If this happens, then IO can still be in-flight while md tears down
the array and bad things can happen (use-after-free and subsequent
havoc).
So in the case where do_md_stop is being called from an open file
descriptor, call sync_block after taking the mutex to ensure there
will be no new openers.
This is needed when setting a read-write device to read-only too.
Cc: stable@vger.kernel.org
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit c6563a8c38
md: add possibility to change data-offset for devices.
introduced a 'new_data_offset' attribute which should normally
be the same as 'data_offset', but can be explicitly set to a different
value to allow a reshape operation to move the data.
Unfortunately when the 'data_offset' is explicitly set through
sysfs, the new_data_offset is not also set, so the two would become
out-of-sync incorrectly.
One result of this is that trying to set the 'size' after the
'data_offset' would fail because it is not permitted to set the size
when the 'data_offset' and 'new_data_offset' are different - as that
can be confusing.
Consequently when mdadm tried to do this while assembling an IMSM
array it would fail.
This bug was introduced in 3.5-rc1.
Reported-by: Brian Downing <bdowning@lavos.net>
Bisected-by: Brian Downing <bdowning@lavos.net>
Tested-by: Brian Downing <bdowning@lavos.net>
Signed-off-by: NeilBrown <neilb@suse.de>
Pull target fixes from Nicholas Bellinger:
"This includes a bugfix from MDR to address a NULL pointer OOPs with
FCoE aborts, along with a WRITE_SAME emulation bugfix for NOLB=0
cases, and persistent reservation return cleanups from Roland.
All three patches are CC'ed to stable."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix range calculation in WRITE SAME emulation when num blocks == 0
target: Clean up returning errors in PR handling code
tcm_fc: Fix crash seen with aborts and large reads
Commit a7a20d1039 ("sd: limit the scope of the async probe domain")
make the SCSI device probing run device discovery in it's own async
domain.
However, as a result, the partition detection was no longer synchronized
by async_synchronize_full() (which, despite the name, only synchronizes
the global async space, not all of them). Which in turn meant that
"wait_for_device_probe()" would not wait for the SCSI partitions to be
parsed.
And "wait_for_device_probe()" was what the boot time init code relied on
for mounting the root filesystem.
Now, most people never noticed this, because not only is it
timing-dependent, but modern distributions all use initrd. So the root
filesystem isn't actually on a disk at all. And then before they
actually mount the final disk filesystem, they will have loaded the
scsi-wait-scan module, which not only does the expected
wait_for_device_probe(), but also does scsi_complete_async_scans().
[ Side note: scsi_complete_async_scans() had also been partially broken,
but that was fixed in commit 43a8d39d01 ("fix async probe
regression"), so that same commit a7a20d1039 had actually broken
setups even if you used scsi-wait-scan explicitly ]
Solve this problem by just moving the scsi_complete_async_scans() call
into wait_for_device_probe(). Everybody who wants to wait for device
probing to finish really wants the SCSI probing to complete, so there's
no reason not to do this.
So now "wait_for_device_probe()" really does what the name implies, and
properly waits for device probing to finish. This also removes the now
unnecessary extra calls to scsi_complete_async_scans().
Reported-and-tested-by: Artem S. Tashkinov <t.artem@mailcity.com>
Cc: Dan Williams <dan.j.williams@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <jbottomley@parallels.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: linux-scsi <linux-scsi@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The VIDIOC_DV_TIMINGS_CAP ioctl check wasn't added to determine_valid_ioctls().
This caused this ioctl to always return -ENOTTY.
The cause for this was that for 3.5 two patch series were merged, one
changing V4L2 core ioctl handling and one adding new functionality, and
some of the new functionality wasn't handled by the new V4L2 core code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[ Taking it directly due to vacations - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are arriving very late in the release cycle, but there has been
a change of maintainers on the SPEAr platform and they have needed a
while to get going.
The patch count is higher than I would like at this point, but they're
all relevant fixes and well-contained in their own platform code. I still
think it's suitable 3.5 material and I don't think it should increase
the need for a -rc8 since they are so contained.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=cBuT
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes for SPEAr from Olof Johansson:
"These are arriving very late in the release cycle, but there has been
a change of maintainers on the SPEAr platform and they have needed a
while to get going.
The patch count is higher than I would like at this point, but they're
all relevant fixes and well-contained in their own platform code. I
still think it's suitable 3.5 material and I don't think it should
increase the need for a -rc8 since they are so contained."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: SPEAr600: Fix timer interrupt definition in spear600.dtsi
ARM: dts: SPEAr320: Boot the board in EXTENDED_MODE
ARM: dts: SPEAr320: Fix compatible string
Clk: SPEAr1340: Update sys clock parent array
clk: SPEAr1340: Fix clk enable register for uart1 and i2c1.
ARM: SPEAr13xx: Fix Interrupt bindings
Clk:spear6xx:Fix: Rename clk ids within predefined limit
Clk:spear3xx:Fix: Rename clk ids within predefined limit
clk:spear1310:Fix: Rename clk ids within predefined limit
clk:spear1340:Fix: Rename clk ids within predefined limit
sys_clk has multiple parents and selection of parent depends on sys_clk_ctrl
register bit no. 23:25, with following possibilities
0XX: pll1_clk
10X: sys_synth_clk
110: pll2_clk
111: pll3_clk
Out of several possibilities (h/w wise) to select same clock parent for
sys_clk, current clock implementation was considering just one value.
When bootloader programmed different (valid) value to select a clock
parent then Linux breaks.
Here, we try to include all possibilities which can lead to same
clock selection thus making Linux independent of bootloader selection
values.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
This patch is to fix typing mistake of clk enable register of i2c1 and
uart1.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The max limit of con_id is 16 and dev_id is 20. As of now for spear6xx, many clk
ids are exceeding this predefined limit.
This patch is intended to rename clk ids like:
mux_clk -> _mclk
gate_clk -> _gclk
synth_clk -> syn_clk
ras_gen1_synth_gate_clk -> ras_syn1_gclk
pll3_48m -> pll3_
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The max limit of con_id is 16 and dev_id is 20. As of now for spear3xx, many clk
ids are exceeding this predefined limit.
This patch is intended to rename clk ids like:
mux_clk -> _mclk
gate_clk -> _gclk
synth_clk -> syn_clk
ras_gen1_synth_gate_clk -> ras_syn1_gclk
ras_pll3_48m -> ras_pll3_
pll3_48m -> pll3_
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The max limit of con_id is 16 and dev_id is 20. As of now for spear1310, many
clk ids are exceeding this predefined limit.
This patch is intended to rename clk ids like:
mux_clk -> _mclk
gate_clk -> _gclk
synth_clk -> syn_clk
gmac_phy -> phy_
gmii_125m_pad -> gmii_pad
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The max limit of con_id is 16 and dev_id is 20. As of now for spear1340, many
clk ids are exceeding this predefined limit.
This patch rename clk ids like:
mux_clk -> _mclk
gate_clk -> _gclk
synth_clk -> syn_clk
gmac_phy -> phy_
gmii_125m_pad_ -> gmii_pad
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Sparse complains about this because:
drivers/block/rbd.c:996:20: warning: cast to restricted __le32
drivers/block/rbd.c:996:20: warning: cast from restricted __le16
These are set in osd_req_encode_op() and they are le16.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alex Elder <elder@inktank.com>
(cherry picked from commit 895cfcc810)
ceph_snap_context->snaps is an u64 array
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Reviewed-by: Alex Elder <elder@inktank.com>
(cherry picked from commit f9f9a19044)
Pull networking fixes from David Miller:
1) IPVS oops'ers:
a) Should not reset skb->nf_bridge in forwarding hook (Lin Ming)
b) 3.4 commit can cause ip_vs_control_cleanup to be invoked after
the ipvs_core_ops are unregistered during rmmod (Julian ANastasov)
2) ixgbevf bringup failure can crash in TX descriptor cleanup
(Alexander Duyck)
3) AX25 switch missing break statement hoses ROSE sockets (Alan Cox)
4) CAIF accesses freed per-net memory (Sjur Brandeland)
5) Network cgroup code has out-or-bounds accesses (Eric DUmazet), and
accesses freed memory (Gao Feng)
6) Fix a crash in SCTP reported by Dave Jones caused by freeing an
association still on a list (Neil HOrman)
7) __netdev_alloc_skb() regresses on GFP_DMA using drivers because that
GFP flag is not being retained for the allocation (Eric Dumazet).
8) Missing NULL hceck in sch_sfb netlink message parsing (Alan Cox)
9) bnx2 crashes because TX index iteration is not bounded correctly
(Michael Chan)
10) IPoIB generates warnings in TCP queue collapsing (via
skb_try_coalesce) because it does not set skb->truesize correctly
(Eric Dumazet)
11) vlan_info objects leak for the implicit vlan with ID 0 (Amir
Hanania)
12) A fix for TX time stamp handling in gianfar does not transfer socket
ownership from one packet to another correctly, resulting in a
socket write space imbalance (Eric Dumazet)
13) Julia Lawall found several cases where we do a list iteration, and
then at the loop termination unconditionally assume we ended up with
real list object, rather than the list head itself (CNIC, RXRPC,
mISDN).
14) The bonding driver handles procfs moving incorrectly when a device
it manages is moved from one namespace to another (Eric Biederman)
15) Missing memory barriers in stmmac descriptor accesses result in
various crashes (Deepak Sikri)
16) Fix handling of broadcast packets in batman-adv (Simon Wunderlich)
17) Properly check the sanity of sendmsg() lengths in ieee802154's
dgram_sendmsg(). Dave Jones and others have hit and reported this
bug (Sasha Levin)
18) Some drivers (b44 and b43legacy) on 64-bit machines stopped working
because of how netdev_alloc_skb() was adjusted. Such drivers should
now use alloc_skb() for obtaining bounce buffers. (Eric Dumazet)
19) atl1c mis-managed it's link state in that it stops the queue by hand
on link down. The generic networking takes care of that and this
double stop locks the queue down. So simply removing the driver's
queue stop call fixes the problem (Cloud Ren)
20) Fix out-of-memory due to mis-accounting in net_em packet scheduler
(Eric Dumazet)
21) If DCB and SR-IOV are configured at the same time in IXGBE the chip
will hang because this is not supported (Alexander Duyck)
22) A commit to stop drivers using netdev->base_addr broke the CNIC
driver (Michael Chan)
23) Timeout regression in ipset caused by an attempt to fix an overflow
bug (Jozsef Kadlecsik).
24) mac80211 minstrel code allocates memory using incorrect size
(Thomas Huehn)
25) llcp_sock_getname() needs to check for a NULL device otherwise we
OOPS (Sasha Levin)
26) mwifiex leaks memory (Bing Zhao)
27) Propagate iwlwifi fix to iwlegacy, even when we're not associated
we need to monitor for stuck queues in the watchdog handler
(Stanislaw Geuszka)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
ipvs: fix oops in ip_vs_dst_event on rmmod
ipvs: fix oops on NAT reply in br_nf context
ixgbevf: Fix panic when loading driver
ax25: Fix missing break
MAINTAINERS: reflect actual changes in IEEE 802.15.4 maintainership
caif: Fix access to freed pernet memory
net: cgroup: fix access the unallocated memory in netprio cgroup
ixgbevf: Prevent RX/TX statistics getting reset to zero
sctp: Fix list corruption resulting from freeing an association on a list
net: respect GFP_DMA in __netdev_alloc_skb()
e1000e: fix test for PHY being accessible on 82577/8/9 and I217
e1000e: Correct link check logic for 82571 serdes
sch_sfb: Fix missing NULL check
bnx2: Fix bug in bnx2_free_tx_skbs().
IPoIB: fix skb truesize underestimatiom
net: Fix memory leak - vlan_info struct
gianfar: fix potential sk_wmem_alloc imbalance
drivers/net/ethernet/broadcom/cnic.c: remove invalid reference to list iterator variable
net/rxrpc/ar-peer.c: remove invalid reference to list iterator variable
drivers/isdn/mISDN/stack.c: remove invalid reference to list iterator variable
...
eliminates the dependency on arbitrary initialization orders.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JsP6
-----END PGP SIGNATURE-----
Merge tag 'single-rpmsg-3.5-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/rpmsg
Pull rpmsg fix from Ohad Ben-Cohen:
"A single rpmsg fix for 3.5, coming from Federico Fuga, which
eliminates the dependency on arbitrary initialization orders."
* tag 'single-rpmsg-3.5-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/rpmsg:
rpmsg: fix dependency on initialization order
When rpmsg drivers are built into the kernel, they must not initialize
before the rpmsg bus does, otherwise they'd trigger a BUG() in
drivers/base/driver.c line 169 (driver_register()).
To fix that, and to stop depending on arbitrary linkage ordering of
those built-in rpmsg drivers, we make the rpmsg bus initialize at
subsys_initcall.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Federico Fuga <fuga@studiofuga.com>
[ohad: rewrite the commit log]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
This patch addresses a kernel panic seen when setting up the interface.
Specifically we see a NULL pointer dereference on the Tx descriptor cleanup
path when enabling interrupts. This change corrects that so it cannot
occur.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains fixes to e1000e.
...
Bruce Allan (1):
e1000e: fix test for PHY being accessible on 82577/8/9 and I217
Tushar Dave (1):
e1000e: Correct link check logic for 82571 serdes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 4197aa7bb8 implements 64 bit
per ring statistics. But the driver resets the 'total_bytes' and
'total_packets' from RX and TX rings in the RX and TX interrupt
handlers to zero. This results in statistics being lost and user space
reporting RX and TX statistics as zero. This patch addresses the
issue by preventing the resetting of RX and TX ring statistics to
zero.
Signed-off-by: Narendra K <narendra_k@dell.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NUMBER OF LOGICAL BLOCKS is 0, WRITE SAME is supposed to write
all the blocks from the specified LBA through the end of the device.
However, dev->transport->get_blocks(dev) (perhaps confusingly) returns
the last valid LBA rather than the number of blocks, so the correct
number of blocks to write starting with lba is
dev->transport->get_blocks(dev) - lba + 1
(nab: Backport roland's for-3.6 patch to for-3.5)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- instead of (PTR_ERR(file) < 0) just use IS_ERR(file)
- return -EINVAL instead of EINVAL
- all other error returns in target_scsi3_emulate_pr_out() use
"goto out" -- get rid of the one remaining straight "return."
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Merge gma500 patches from Alan Cox.
* Merge emailed patches from Alan Cox <alan@lxorguk.ukuu.org.uk>: (3 commits)
gma500,cdv: Fix the brightness base
gma500: move the ASLE enable
gma500: Fix lid related crash
Some desktop environments carefully save and restore the brightness
settings from the previous boot. Unfortunately they don't all check to
see if the range has changed. The end result is that they restore a
brightness of 100/lots not 100/100.
As the old driver and the non-free GMA36xx driver both use 0-100 we thus
need to go back doing the same thing to avoid users getting a mysterious
black screen after boot.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Otherwise we end up getting the masks wrong, can get events before we
are doing power control and other ungood things. Again this is a
regression fix where the ordering of handling was disturbed by other
work, and the user experience on some boxes is a blank screen.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We now set up the lid timer before we set up the backlight. On some
devices that causes a crash as we do a backlight change before or during
the setup.
As this fixes a crash on boot regression on some setups it ought to go
in ASAP, especially as all the user gets is a blank screen.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Tested-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 platform tree fixes from Matthew Garrett:
"Small fixes to a couple of drivers plus a slightly larger number for
sony-laptop that the maintainer thinks are appropriate, most of which
fix problems with the earlier 3.5 updates. These have been in -next
for a while without complaint."
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
intel_ips: blacklist HP ProBook laptops
ideapad: uninitialized data in ideapad_acpi_add()
sony-laptop: correct find_snc_handle failure checks
sony-laptop: fix a couple signedness bugs
sony-laptop: fix sony_nc_sysfs_store()
sony-laptop: input initialization should be done before SNC
sony-laptop: add lid backlight support for handle 0x143
sony-laptop: store battery care limits on batteries
sony-laptop: notify userspace of GFX switch position changes
sony-laptop: use an enum for SNC event types
- Two fixes to the i.MX driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ucSC
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull late pinctrl fixes from Linus Walleij:
- Two fixes to the i.MX driver
* tag 'fixes-for-v3.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: pinctrl-imx6q: add missed mux function for USBOTG_ID
pinctrl: pinctrl-imx: only print debug message when DEBUG is defined
The idr_pre_get() function never returns a value < 0. It returns 0 (no
memory) or 1 (OK).
Reported-by: Silva Paulo <psdasilva@yahoo.com>
[ Rewrote Silva's patch, but attributing it to Silva anyway - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a crash seen when large reads have their exchange
aborted by either timing out or being reset. Because the exchange
abort results in the seq pointer being set to NULL, because the
sequence is no longer valid, it must not be dereferenced. This
patch changes the function ft_get_task_tag to return ~0 if it is
unable to get the tag for this reason. Because the get_task_tag
interface provides no means of returning an error, this seems
like the best way to fix this issue at the moment.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Bhanu Prakash Gollapudi