BCM6338 and BCM6348 have a message control register width of 8 bits, instead
of 16-bits like what the SPI driver assumes right now. Also the SPI message
type shift value of 14 is actually 6 for these SoCs.
This resulted in transmit FIFO corruption because we were writing 16-bits
to an 8-bits wide register, thus spanning on the first byte of the transmit
FIFO, which had already been filed in bcm63xx_spi_fill_txrx_fifo().
Fix this by passing the message control register width and message type
shift through platform data back to the SPI driver so that it can use
it properly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: grant.likely@secretlab.ca
Cc: spi-devel-general@lists.sourceforge.net
Cc: jonas.gorski@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/3983/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This allows booting to command line. Ethernet is not supported yet,
but PCIe connected wireless should work.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/3958/
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the PCIe port found on BCM6328.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/3956/
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This includes CPU speed, memory size detection and working UART, but
lacking the appropriate drivers, no support for attached flash.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/3951/
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Newer BCM63XX SoCs use virtually the same CPU ID, differing only in the
revision bits. But since they all have the Chip ID register at the same
location, we can use that to identify the SoC we are running on.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/3955/
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On BCM6358 and BCM6368 the attached flash type is exposed through a
bootstrapping register. Use it for auto detecting the flash type on
those and default to parallel flash for earlier SoCs.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/3954/
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There is only one watchdog and VoIP DSP platform devices per board, use
-1 as the platform_device id accordingly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3313/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds the necessary stub to register the SPI platform driver.
Since the registers are shuffled between the 4 BCM63xx CPUs supported by
this SPI driver we also need to generate the internal register layout and
export this layout for the driver to use it properly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: grant.likely@secretlab.ca
Cc: spi-devel-general@lists.sourceforge.net
Patchwork: https://patchwork.linux-mips.org/patch/3321/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the _CLK suffix from the BCM6368 clock bits definitions to be
consistent with what is already present.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3312/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As long as there is no other non-const variable marked __initdata in the
same compilation unit it doesn't hurt. If there were one however
compilation would fail with
error: $variablename causes a section type conflict
because a section containing const variables is marked read only and so
cannot contain non-const variables.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: kernel@pengutronix.de
Patchwork: https://patchwork.linux-mips.org/patch/3565/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In case the MAC address pool is not big enough to also register a WLAN device
prefer registering the Ethernet devices.
[ralf@linux-mips.org: Fixed formatting as per Sergei's complaint.]
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3013/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On BCM6345, the register offsets for the set/get GPIO registers is wrong.
Use the same logic as the one present in arch/mips/bcm63xx/irq.c to
define the correct gpio_out_low_reg value when support for BCM6345
is compiled in.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3010/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Though BCM6345 does not technically have the same MPI register layout
than the other SoCs, reading the chip-select registers is done the same
way, and particularly for chip-select 0, which is the boot flash.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3009/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of hardcoding the amount of available RAM, read the number of
effective multiples of 8MB from SDRAM_MBASE_REG.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3008/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some device registration (eg leds), expect subsystem initcall to be
run first, so move board device registration to device_initcall().
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2891/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Mark interrupts with no_action handler, cascade interrupts, low level
interrupts (bus error, halt ..) with IRQF_NO_THREAD to exclude them
from forced threading.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some embedded devices like the Netgear WNDR3300 have two SSB based cards
without an own sprom on the pci bus. We have to provide two different
fallback sproms for these and this was not possible with the old solution.
In the bcm47xx architecture the sprom data is stored in the nvram in the
main flash storage. The architecture code will be able to fill the sprom
with the stored data based on the bus where the device was found.
The bcm63xx code should do the same thing as before, just using the new
API.
Acked-by: Michael Buesch <mb@bu3sch.de>
Cc: netdev@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2362/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
BMIPS processor cores are used in 50+ different chipsets spread across
5+ product lines. In many cases the chipsets do not share the same
peripheral register layouts, the same register blocks, the same
interrupt controllers, the same memory maps, or much of anything else.
But, across radically different SoCs that share nothing more than the
same BMIPS CPU, a few things are still mostly constant:
SMP operations
Access to performance counters
DMA cache coherency quirks
Cache and memory bus configuration
So, it makes sense to treat each BMIPS processor type as a generic
"building block," rather than tying it to a specific SoC. This makes it
easier to support a large number of BMIPS-based chipsets without
unnecessary duplication of code, and provides the infrastructure needed
to support BMIPS-proprietary features.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: mbizon@freebox.fr
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Florian Fainelli <ffainelli@freebox.fr>
Patchwork: https://patchwork.linux-mips.org/patch/1706/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
Add missing #inclusions of <linux/irq.h> to a whole bunch of files that should
really include it. Note that this can replace #inclusions of <asm/irq.h>.
This is required for the patch to sort out irqflags handling function naming to
compile on MIPS.
The problem is that these files require access to things like setup_irq() -
which isn't available by #including <linux/interrupt.h>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
This is too generic a name, so prefix it with BCM63XX_ to avoid potential
namespace clashes when including <asm/gpio.h>.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1171/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 2083e8327aeeaf818b0e4522a9d2539835c60423, the SPROM is now registered
in the board_prom_init callback, but it references variables and functions
which are declared below. Move the variables and functions above
board_prom_init.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1077/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To avoid a glitch during GPIO initialisation read GPIO output register
values left by the firmware.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/903/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The BCm63xx SOC has two uarts. Some boards use the second one for
bluetooth. This patch changes platform device registration code to
handle this. Changes to the UART driver were already merged in
6a2c7eabfd.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
To: linux-mips@linux-mips.org
Cc: Maxime Bizon <mbizon@freebox.fr>
Patchwork: http://patchwork.linux-mips.org/patch/900/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
bcm63xx_gpio_init is already called from prom_init to allow board to use
them early, so we can remove the unneeded arch_initcall.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
To: linux-mips@linux-mips.org
Cc: Maxime Bizon <mbizon@freebox.fr>
Patchwork: http://patchwork.linux-mips.org/patch/899/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Florian Fainelli