Fix output from checkpatch.pl like:
Block comments use a trailing */ on a separate lin
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch helps to fix TPC stats to display the stats
properly. Here cosmetic change has been done to print the
TPC stats for all the cases 1.CDD 2.STBC 3.TXBF
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove obselete Copy Engine comments referring to the function
ath10k_ce_sendlist_send as this function was removed long time back
by the commit 2e761b5a52 ("ath10k: remove ce_sendlist_send").
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add an ath10k HTC debug message when insufficient tx credits
are available to send the WMI commands. This is very useful
in debugging issues like 'tx credit starvation' that could
possibly happen with multiclient setup with constant roaming
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It seems set_coverage_class_work is not cancelled anywhere,
though I could not find a crash/warning with this existing
design, its safer to cancel it during stop() and also before
restarting the hardware.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If station advertises diffferent NSS capabilities in Rx_mcs set
of HT and VHT IEs in assoc req, the current NSS computation
logic configures the NSS support only based on Rx_mcs set of
HT capabilities in the driver. This is configuring the station
NSS capabilities incorreclty in the target.
For example, if station advertise Rx_mcs set as 2 spatial streams
in HT capabilities and 1 spatial streams in VHT capabilities in
assoc request, as per current logic we are calculating nss from
HT capabilities and the driver sets peer_num_spatial_streams as
2 for the station which is configured in VHT 1*1.
This patchs fix this issue by calculating the nss from VHT cap if
station supports vht.
Signed-off-by: Venkateswara Rao Naralasetty <c_vnaral@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: 36bcce4306 ("ath9k_htc: Handle storage devices")
Cc: stable <stable@vger.kernel.org> # 2.6.39+
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move NAPI enable to 'ath10k_ahb_hif_start' from
'ath10k_ahb_hif_power_up'. This is to maintain the symmetry
of calling napi_enable() from ath10k_ahb_hif_start() so that it
matches with napi_disable() being called from ath10k_pci_hif_stop().
This change is based on the crash fix from Kalle for PCI interface in
commit 1427228d58 ("ath10k: fix napi crash during rmmod when probe
firmware fails").
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Channels 34/38/42/46 can only be used for compatibility with old devices sold
in Japan. Modern products, such as AR6003/AR6004 don't support these channels.
Keeping them in the upstream is error prone and requires full network stack
support. A custom patch should be used in case such compatibility is required.
Without this one, a user is able to start an AP using wpa_supplicant,
for example, on one of these channels (34/38/42/46), without getting
any warning/error from the cfg80211 or ath6kl - which is correct
(since these channels match regdom rules). However, the AR6003 and its
firmware (we're using v3.4.0.225) will fail and return
"WMI_CMDERROR_EVENTID" with "INVALID_PARAM" error code.
Signed-off-by: Rostyslav Khudolii <rkhudolii@airtame.com>
Cc: Attila Sukosd <attila@airtame.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The check of len > buf_len is redundant as len is initialized
to 0 and buf_len to 4096, so this comparison is always false.
Remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix typo (spelling mistake) in wmi.h
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
I failed to notice that commit 523f6701db ("ath10k: update available channel
list for 5G radio") added two new warnings:
drivers/net/wireless/ath/ath10k/mac.c:3129:6: warning: symbol 'ath10k_mac_update_channel_list' was not declared. Should it be static?
drivers/net/wireless/ath/ath10k/mac.c:3170: Alignment should match open parenthesis
Fix those.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fetch target operating channel during potential radar detection when
the interface is just brought up, but no channel is assigned from
userspace. In this scenario rx_channel may not be having a valid pointer
hence fetch the target operating channel to avoid warnings as below
which can be triggered by the commands with DFS testing over longer run
comamnds:
iw wlan1 set type mesh
ifconfig wlan1 up (valid tgt_oper_chan only)
iw wlan1 cac trigger freq 5260 HT20 (valid rx_channel, tgt_oper_chan)
iw wlan1 cac trigger freq 5280 HT20
iw wlan1 cac trigger freq 5300 HT20
Once the CAC expires, current channel context will be removed and
we are only left with the fallback option of using 'target operating
channel'
Firmware and driver log:
ath: phy1: DFS: radar found on freq=5300: id=1, pri=1125, count=5,
count_false=4
ath: phy1: DFS: radar found on freq=5260: id=5, pri=3151, count=6,
count_false=11
ath: phy1: DFS: radar found on freq=5280: id=1, pri=1351, count=6,
count_false=4
ath: phy1: DFS: radar found on freq=5300: id=1, pri=1125, count=5,
count_false=4
ath10k_pci 0001:01:00.0: failed to derive channel for radar pulse,
treating as radar
ath10k_pci 0001:01:00.0: failed to derive channel for radar pulse,
treating as radar
Call trace:
WARNING: CPU: 1 PID: 2145 at
backports-20161201-3.14.77-9ab3068/net/wireless/chan.c:265
cfg80211_set_dfs_state+0x3c/0x88 [cfg80211]()
Workqueue: phy1 ieee80211_dfs_radar_detected_work
[mac80211]
[<c0320770>] (warn_slowpath_null) from [<bf79b90c>]
(cfg80211_set_dfs_state+0x3c/0x88 [cfg80211])
[<bf79b90c>] (cfg80211_set_dfs_state [cfg80211]) from
[<bf79697c>] (cfg80211_radar_event+0xc4/0x140 [cfg80211])
[<bf79697c>] (cfg80211_radar_event [cfg80211]) from
[<bf83c058>] (ieee80211_dfs_radar_detected_work+0xa8/0xb4 [mac80211])
[<bf83c058>] (ieee80211_dfs_radar_detected_work
[mac80211]) from [<c0339518>] (process_one_work+0x298/0x4a4)
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The check on ret for an error is redundant because it is already been
checked for non-zero earlier on and ret is never non-zero at this point.
Fix this by removing the redundant check and error message.
Detected by CoverityScan, CID#1357170 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Doing so enables the FFT generation without prior
configuration, leading to an IRQ storm caused by
invalid (or at least unwanted) PHY errors.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If a 5 GHz radio is calibrated for operation in both
the low band (channels 36 to 64) and high band(channels 100 to 169),
hardware allows operations in all the listed channels. However,
if the chip has been calibrated only for the low/high band and
a high/low band channel is configured, due to lack of calibration
there will be potentially invalid signal on those non calibrated channels.
To avoid this problem this patch sets IEEE80211_CHAN_DISABLED flag for
those non calibrated channels by using low_5ghz_chan and high_5ghz_chan
values which we get from target through wmi service ready event.
Driver initialized flags are getting re initialized in handle_channel
in cfg80211. So calling the function to disable the non supported channel
from reg_notifier().
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If DFS is not enabled in hostapd (ieee80211h=0) DFS channels shall
not be available for use even though the hardware may have the capability
to support DFS. With this configuration (DFS disabled in hostapd) trying to
bring up ath10k device in DFS channel for AP mode fails and trying to
simulate DFS in ath10k debugfs results in a warning in cfg80211 complaining
invalid channel and this should be avoided in the driver itself rather than
false propogating RADAR detection to mac80211/cfg80211. Fix this by
checking for the first vif 'is_started' state(should work for client mode
as well) as all the vifs shall be configured for the same channel
sys/kernel/debug/ieee80211/phy1/ath10k# echo 1 > dfs_simulate_radar
WARNING: at net/wireless/chan.c:265 cfg80211_radar_event+0x24/0x60
Workqueue: phy0 ieee80211_dfs_radar_detected_work [mac80211]
[<c022f2d4>] (warn_slowpath_null) from
[<bf72dab8>] (cfg80211_radar_event+0x24/0x60 [cfg80211])
[<bf72dab8>] (cfg80211_radar_event [cfg80211]) from
[<bf7813e0>] (ieee80211_dfs_radar_detected_work+0x94/0xa0 [mac80211])
[<bf7813e0>] (ieee80211_dfs_radar_detected_work [mac80211]) from
[<c0242320>] (process_one_work+0x20c/0x32c)
WARNING: at net/wireless/nl80211.c:2488 nl80211_get_mpath+0x13c/0x4cc
Workqueue: phy0 ieee80211_dfs_radar_detected_work [mac80211]
[<c022f2d4>] (warn_slowpath_null) from
[<bf72dab8>] (cfg80211_radar_event+0x24/0x60 [cfg80211])
[<bf72dab8>] (cfg80211_radar_event [cfg80211]) from
[<bf7813e0>] (ieee80211_dfs_radar_detected_work+0x94/0xa0 [mac80211])
[<bf7813e0>] (ieee80211_dfs_radar_detected_work [mac80211]) from
[<c0242320>] (process_one_work+0x20c/0x32c)
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a new value to the oob_mode module parameter for
supporting AP certification.
All enabled values of oob_mode (>0) are intended only
for debugging and diagnostics.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver always invoke cfg80211_disconnected() with locally_generated as
false.
Fix this by reporting true whenever the disconnect is triggered from
upper layers (cfg80211) or from within the driver itself (reset,
deinit).
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Upon connect timeout driver invokes _wil6210_disconnect() which iterates
over sta array and disconnects each connected sta. In practice, because
the connection is still ongoing and because cid is not yet allocated,
disconnect is not actually happening. This leaves FW in connecting
state while driver is in disconnected state.
To fix this, upon connect timeout, explicitly send WMI_DISCONNECT_CMDID
to FW to make sure it gets disconnected.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When flush is done, pending events list is manipulated
without taking the proper spinlock, which could lead to
memory corruption if list is manipulated by wmi worker
or by interrupt routine.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In a fast disconnect/connect sequence, cfg80211_connect_result() can
fail to find the bss object which the driver is connecting to. Detailed
sequence of events:
* Driver is connected in STA mode
* Disconnect request arrives from user space. Driver disconnects and
calls cfg80211_disconnected() which adds new event to the
cfg80211_wq worker thread
* Connect request arrives from user space. cfg80211_connect() stores
ssid/ssid_len and calls rdev_connect()
* __cfg80211_disconnected() runs in worker thread and zero
wdev->ssid_len
* Connect succeeds. Driver calls cfg80211_connect_result() which fails
to find the bss because wdev->ssid_len is zero
To overcome this, upon connect request, store the bss object in the
driver and upon connect completion pass it to kernel using
cfg80211_connect_bss().
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After setting HALP ICR bit, we keep it set until HALP unvote.
Masking HALP ICR should protect the driver from hitting the HALP ICR
over and over again. However, in case there is another MISC ICR
we will read the HALP ICR and issue a completion. This can lead to
a case where HALP voting is completed immediately, as the completion
is already set.
Reinit the HALP completion before the actual vote will clear previous
completions and protect from such cases.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some dynamic debug printouts in driver are using print_hex_dump_bytes.
However, with dynamic debug disabled, print_hex_dump_bytes outputs to
log unconditionally.
Use print_hex_dump_debug instead to prevent log pollution when dynamic
debug disabled.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The driver uses the bus_request platform operation to
request resources from the platform for a specific bandwidth.
Currently the driver requests resources for the maximum
theoretical bandwidth, when interface is brought up.
Refine this process a bit: now the driver will request a
small amount of resources when interface is up, and will only
issue the maximum request when connected.
This mechanism will be improved further in the future to make
more refined requests based on actual bandwidth.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The driver should not allow starting any type of scan on a stopped
P2P device. Current implementation only checked social scan.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
device supports 48bit addresses, reflect that by
setting the dma mask accordingly.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Reorder 'out_free_dxe_pool' and 'out_free_dxe_ctl' error handling labels
in order to match the way resources have been allocated.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Doing a channel switch via hostapd_cli seems to update
the new channel context for each VAP's appropriately as below
in 'ath10k_mac_update_vif_chan', hence we can safely suppress the
warning that shows up during this operation and dump the warning only
if no vaps are available for channel switch
hostapd_cli -i wlan0 chan_switch 5 5200
OK
ath10k_pci : mac chanctx switch n_vifs 3 mode 1
ath10k_pci : mac chanctx switch vdev_id 2 freq 5180->5200 width 0->0
ath10k_pci : mac chanctx switch vdev_id 1 freq 5180->5200 width 0->0
ath10k_pci : mac chanctx switch vdev_id 0 freq 5180->5200 width 0->0
Call Trace:
WARNING: backports-20161201-3.14.77-9ab3068/drivers/net/wireless/ath/ath10k/mac.c:7126
[<c022f2d4>] (warn_slowpath_null) from [<bf7f150c>]
(ath10k_reconfig_complete+0xe4/0x25c [ath10k_core])
[<bf7f150c>] (ath10k_reconfig_complete [ath10k_core])
[<bf7f35f0>] (ath10k_mac_vif_ap_csa_work+0x214/0x370 [ath10k_core])
[<bf7f38b8>] (ath10k_mac_op_change_chanctx+0x108/0x128 [ath10k_core])
[<bf782ac0>] (ieee80211_recalc_chanctx_min_def+0x30c/0x430 [mac80211])
[<bf7830a4>] (ieee80211_recalc_smps_chanctx+0x2ec/0x840 [mac80211])
[<bf7843e8>] (ieee80211_vif_use_reserved_context+0x7c/0xf8 [mac80211])
[<bf7843e8>] (ieee80211_vif_use_reserved_context [mac80211])
[<bf76e5d4>] (ieee80211_csa_finalize_work+0x5c/0x88 [mac80211])
Fixes: d7bf4b4aba ("ath10k: fix ar->rx_channel updating logic")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9377 is the family of QCA61x4 which shared the same procedure
to enable the hardware clock that could improve the firmware download time.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Len Brown reported the system resume time is taking more than 2 seconds in
bug - https://bugzilla.kernel.org/show_bug.cgi?id=185621.
The reason of the 2 seconds is due to the firmware download time.
The chip is booted up in the default reference clock speed to handle the
firmware download to chip memory and advanced to the support higher speed
clock to run the firmware after all. The default reference clock in the
hardware is slow so that the firmware download time is taking up to 2
seconds for a 600KB firmware file.
[76796.349701] ath10k_pci : boot uploading firmware image len 688691
[76798.334612] ath10k_pci : htt tx max num pending tx 1056
The resolution here is to enable the higher speed clock if the hardware
supported before the firmware download at BMI stage, so that the hardware
can handle the firmare download in a more efficient way. This can help to
improve the firmware download time from 2 seconds to around 500ms for the
same 600KB firmware file.
[322858.577919] ath10k_pci boot uploading firmware image len 688691
[322859.093094] ath10k_pci htt tx max num pending tx 1056
The steps to advance to the higher speed clock is very hardware specific,
so adding the hardware ops for the hardware that can support this.
Reported-by: Len Brown <lenb@kernel.org>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Adjust the impedance values of the RX and TX lanes in the SGMII block
so that they are closer to optimal values.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement suspend/resume callbacks in the bgmac driver. This makes sure
that we de-initialize and re-initialize the hardware correctly before
entering suspend and when resuming.
Signed-off-by: Joey Zhong <zhongx@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM471X and BCM535X are of the same family (from what I can derive from
internal documents). Group them into the case statement together, which
results in more code reuse.
Also, use existing helper variables to make the code a little more
readable too.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum frame size is really just the standard ethernet frame size
and FCS. So use those existing defines to make the code a little more
beautiful.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() to set a random MAC address in order to make
sure ndev->addr_assign_type will be properly set to NET_ADDR_RANDOM.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use NAPI (softirq), to handle receive packets and send completions.
Previously this was handled by tasklet.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is mostly just a refactoring of previous functions
(get_pkt_next_raw, put_pkt_raw and commit_rd_index) to make it easier
to use for other drivers and NAPI.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two variables named packet in the same function. One is the
metadata descriptor from host (vmpacket_descriptor) and the other is
the control block in the skb used to hold metadata from send.
Change name to avoid possible confusion and bugs.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Rokicki