Add a resource managed regulator_get_exclusive()
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add define for __FAN53555_H__ to prevent multiple include of the header file.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds devicetree bindings for max8660, along with some
documentation.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
While the majority of supplies on devices are mandatory and can't be
physically omitted for electrical reasons some devices do have optional
supplies and need to know if they are missing, MMC being the most common
of these.
Currently the core accurately reports all errors when regulators are
requested since it does not know if the supply is one that must be provided
even if by a regulator software does not know about or if it is one that
may genuinely be disconnected. In order to allow this behaviour to be
changed and stub regulators to be provided in the former case add a new
regulator request function regulator_get_optional() which provides a hint
to the core that the regulator may genuinely not be connected.
Currently the implementation is identical to the current behaviour, future
patches will add support in the core for returning stub regulators in the
case where normal regulator_get() fails and the board has requested it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Add pfuze100 regulator driver.
Signed-off-by: Robin Gong <b38343@freescale.com>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some hardwares support disabling ramp delay, so adding ramp_disable flag to
constraints. It will be used to figure out whether ramp_delay in constraints
is explicitly set to zero or its unintialized (zero by default).
And we don't need to call set_voltage_time_sel() for regulators for whom ramp
delay is disabled in constraints.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Many regulators have several linear ranges of selector with different
step sizes, for example offering better resolution at lower voltages.
Provide regulator_{map,list}_voltage_linear_range() allowing these
regulators to use generic code. To do so a table of regulator_linear_range
structs needs to be pointed to from the descriptor.
This was inspired by similar code included in a driver submission from
Chao Xie and Yi Zhang at Marvell.
Signed-off-by: Mark Brown <broonie@linaro.org>
The expected semantic for something expressed as a tolerance is that it
should deliver the specified value with some deviation allowed but this
is not what set_voltage_tol() currently does. Instead it just passes
the maximum possible range to set_voltage() which will typically result
in a voltage aimed at lower than the target voltage.
Instead first try to set a voltage between the target voltage and the
upper limit, then fall back on the full range. This will be much more
robust against physical variation in systems and makes the API behave
more like users would expect.
Signed-off-by: Mark Brown <broonie@linaro.org>
Some platforms don't support the AB8500 external regulators, so instead
of having a list of is_<platform>() calls prior to calling
ab8500_ext_regulator_init() from ab8500_regulator_probe(), we can only
register as a platform device on platforms which require them. It means
we also have more control over them when booting with Device Tree.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonielinaro.org>
Add regulator_get_linear_step(), which returns the voltage step size
between VSEL values for linear regulators. This is intended for use
by regulator consumers which build their own voltage-to-VSEL tables.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Reviewed-by: Andrew Chew <achew@nvidia.com>
Cc: Matthew Longnecker <mlongnecker@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A lot of regulator hardware has ascendant voltage list.
This patch adds regulator_map_voltage_ascend() and export it.
Drivers that have ascendant voltage list can use this as their map_voltage()
operation, this is more efficient than default regulator_map_voltage_iterate()
function.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ab8500_ext_regulator_exit() never fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds Device Tree support to max8952 regulator driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch modifies platform data structure of max8952 driver to
use pointer to regulator_init_data struct instead of embedding it.
This is a prerequisite for adding Device Tree support for the driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce aux5, aux6 into ab8540 regulator framework.
Signed-off-by: Zhenhua HUANG <zhenhua.huang@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Maxime COQUELIN <maxime.coquelin@stericsson.com>
Reviewed-by: David PARIS <david.paris@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Before the AB8500 External Regulator driver was Mainlined, it used
to be conditionally compiled in using the CONFIG_REGULATOR_AB8500_EXT
flag. During the review process that capability was removed, but the
guard controlling prototyping slipped though the net. This patch
cleans it up.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To obtain full AB8540 regulator support, the AB8500 regulator driver
first needs to know its register layout and their initialisation values
for each. That information is provided via a couple of large data
structures which we provide here.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To obtain full AB8505 regulator support, the AB8500 regulator driver
first needs to know its register layout and their initialisation values
for each. That information is provided via a couple of large data
structures which we provide here.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The purpose of this patch is to guarantee that ab8500-debug will
record the regulator registers before they are modified by the
ab8500 regulator driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The USB regulator is controlled by hardware. The software support
was only needed for early hardware (ED) which is no longer supported.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Support for HW request is added in the external regulator
driver. A flag in the board configuration can be set to
let HW control the regulator when there is no SW request.
This means that the regulator will be put in high power
mode when there is a SW request and in HW-request mode
otherwise.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mattias NILSSON <mattias.i.nilsson@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ABx500 is capable of controlling three external regulator supplies.
Most commonly on and off are supported, but if an external regulator
chipset or power supply supports high-power and low-power mode settings,
we can control those too.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Clean out initialisation that is handled by SoC. Regulator
settings for Vpll (partly), Vsmps1, Vsmps2, Vsmps3 (partly),
Vrf1, Varm, Vape, Vbb, Vmod are cleaned out. They should not
be touched by the kernel.
We also update many of the initialisation values to be more
in-line with the current development efforts of ST-Ericsson
internal engineers.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ab8500 MFD should not have knowledge about regulator-
specific platform data like number of regulators and
regulator registers. As the regulator platform data is
about to grow with external regulators, this information
is moved to a new structure provided by the regulator
driver.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Yvan FILLION <yvan.fillion@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch ensures that many of the recent developments pertaining to
the AB8500 regulator device are propagated out into the public arena.
It aims to update some of the existing initialisation values in
accordance with internal ST-Ericsson code submissions. This single
patch was originally a collection of updates which have been squashed
together to aid with clarity.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is already before a register mask in the regulator driver
to allow some bits of a register to be initialized. The register
value is defined in the board configuration. This patch puts a
mask in the board configuration to specify which bits should
actually be altered. The purpose with this patch is to avoid
future mistakes when updating the allowed bits in the regulator
driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch supplies access to some extra settings provided by the
AB8500 regulator device. We also update some of the existing
initialisation values in accordance with internal ST-Ericsson code
submissions. This single patch was originally a collection of updates
which have been squashed together to aid with clarity.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add enable_is_inverted flag to indicate set enable_mask bits to disable
when using regulator_enable_regmap and friends APIs.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The regulator_dev has regulator_enable_gpio structure.
'ena_gpio' and 'ena_gpio_invert' were moved to in regulator_enable_gpio.
regulator_dev ---> regulator_enable_gpio
.ena_gpio .gpio
.ena_gpio_invert .ena_gpio_invert
Pointer, 'ena_pin' is used for checking valid enable GPIO pin.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A Regulator can be enabled by external GPIO pin.
This is configurable in the regulator_config.
At this moment, the GPIO can be owned by only one regulator device.
In some devices, multiple regulators are enabled by shared one GPIO pin.
This patch extends this limitation, enabling shared enable GPIO of regulators.
New list for enable GPIO: 'regulator_ena_gpio_list'
This manages enable GPIO list.
New structure for supporting shared enable GPIO: 'regulator_enable_gpio'
The enable count is used for balancing GPIO control count.
This count is incremented when GPIO is enabled.
On the other hand, it's decremented when GPIO is disabled.
Reference count: 'request_count'
The reference count, 'request_count' is incremented/decremented on
requesting/freeing the GPIO. This count makes sure only free the GPIO
when it has no users.
How it works
If the GPIO is already used, skip requesting new GPIO usage.
The GPIO is new one, request GPIO function and add it to the list of
enable GPIO.
This list is used for balancing enable GPIO count and pin control.
Updating a GPIO and invert code moved
'ena_gpio' and 'ena_gpio_invert' of the regulator_config were moved to
new function, regulator_ena_gpio_request().
Use regulator_enable_pin structure rather than regulator_dev.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's generally important that devices have power when they expect it so
drivers really ought to be checking for errors on the power up paths.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
commit df367931 (regulator: core: Provide regmap get/set bypass
operations) introduced regulator_[gs]et_bypass_regmap
However structure documentation for regulator_desc needs an update.
./scripts/kernel-doc include/linux/regulator/driver.h >/dev/null
generates:
Warning(include/linux/regulator/driver.h:233): No description found for parameter 'bypass_reg'
Warning(include/linux/regulator/driver.h:233): No description found for parameter 'bypass_mask'
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some DVM regulators needs to update apply_bit after setting vsel_reg to
initiate voltage change on the output. This patch adds apply_reg and
apply_bit to struct regulator_desc and update
regulator_set_voltage_sel_regmap() to set apply_bit of apply_reg when
apply_bit is set.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown