This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
This commit implements allocate_resources callback for ff400 protocol.
In this callback, sampling transfer frequency is configured to the
device as well.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
This commit implements allocate_resources callback for ff800 protocol.
As I noted in commit fc716397a5 ("ALSA: fireface: add support for
packet streaming on Fireface 800"), this unit allocates isochronous
resources for tx stream voluntarily. Therefore, this commit is to
maintain isochronous rsources for rx stream. In the callback,
sampling transfer frequency is configured to the device as well.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
In ALSA fireface driver, the allocation of isochronous resources is
programmed in each implementation of protocol. This commit adds
protocol-specific operation for the allocation separated from
the operation to begin session.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pairs of pcm.hw_params callbacks and .hw_free callbacks for both
direction have no differences.
This commit unifies the pairs.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The operation to finish packet streaming corresponds to stopping
isochronous contexts.
This commit applies code refactoring to move codes to stop into
a helper function to finish the session.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After bus reset, isochronous resource manager releases all of allocated
isochronous resources. The nodes to restart packet streaming should
request reallocation of the resources.
However, between the bus-reset and invocation of 'struct fw_driver.update'
handler, ALSA PCM application can detect this situation by XRUN because
the target device cancelled to transmit packets once bus-reset occurs.
Due to the above mechanism, ALSA firewire-tascam driver just stops
packet streaming in the update handler, thus pcm.prepare handler
should request the reallocation.
This commit requests the reallocation in pcm.prepare callback when
bus generation is changed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Once allocated, isochronous resources are available for packet
streaming, even if the streaming is cancelled. For this reason,
current implementation handles allocation of the resources and
starting packet streaming at the same time. However, this brings
complicated procedure to start packet streaming.
This commit separates the allocation and starting. The allocation is
done in pcm.hw_params callback and available till pcm.hw_free callback.
Even if any XRUN occurs, pcm.prepare callback is done to restart
packet streaming for allocated the resources.
There are two points to stop packet streaming; in pcm.hw_params and
pcm.prepare callbacks.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
This commit obsoletes a helper function to release isochronous resources
for both direction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
This commit applies minor code refactoring for a helper function to
allocate isochronous resources.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
The registration of isochronous channels is done just after allocation
of isochronous resources. This commit separates the registration just
before starting packet streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The data for isochronous resources is not destroyed in expected place.
This commit fixes the bug.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 9b2bb4f2f4 ("ALSA: firewire-motu: add stream management functionality")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Based on 1 normalized pattern(s):
licensed under the terms of the gnu general public license version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 88 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000437.521539229@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No big surprises here, just a few device-specific fixes.
HD-audio received several fixes for Acer, Dell, Huawei and other
laptops as well as the workaround for the new Intel chipset.
One significant one-liner fix is the disablement of the node-power
saving on Realtek codecs, which may potentially cover annoying bugs
like the background noises or click noises on many devices.
Other than that, a fix for FireWire bit definitions, and another fix
for LINE6 USB audio bug that was discovered by syzkaller.
-----BEGIN PGP SIGNATURE-----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=Bj5P
-----END PGP SIGNATURE-----
Merge tag 'sound-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"No big surprises here, just a few device-specific fixes.
HD-audio received several fixes for Acer, Dell, Huawei and other
laptops as well as the workaround for the new Intel chipset. One
significant one-liner fix is the disablement of the node-power saving
on Realtek codecs, which may potentially cover annoying bugs like the
background noises or click noises on many devices.
Other than that, a fix for FireWire bit definitions, and another fix
for LINE6 USB audio bug that was discovered by syzkaller"
* tag 'sound-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: fireface: Use ULL suffixes for 64-bit constants
ALSA: hda/realtek - Improve the headset mic for Acer Aspire laptops
ALSA: line6: Assure canceling delayed work at disconnection
ALSA: hda - Force polling mode on CNL for fixing codec communication
ALSA: hda/realtek - Enable micmute LED for Huawei laptops
ALSA: hda/realtek - Set default power save node to 0
ALSA: hda/realtek - Check headset type by unplug and resume
With gcc 4.1:
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_switch_fetching_mode’:
sound/firewire/fireface/ff-protocol-latter.c:97: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_begin_session’:
sound/firewire/fireface/ff-protocol-latter.c:170: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c:197: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c:205: warning: integer constant is too large for ‘long’ type
sound/firewire/fireface/ff-protocol-latter.c: In function ‘latter_finish_session’:
sound/firewire/fireface/ff-protocol-latter.c:214: warning: integer constant is too large for ‘long’ type
Fix this by adding the missing "ULL" suffixes.
Add the same suffix to the last constant, to maintain consistency.
Fixes: fd1cc9de64 ("ALSA: fireface: add support for Fireface UCX")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As a result of heavy refactoring based on IR context header, the packet
handler becomes simpler.
This commit merges the packet handler into function for IR context
callback. The logic to parse IR context header and tracepoints event is
split to a function.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As a result of heavy refactoring based on IT packet header, the packet
handler becomes simpler.
This commit merges the packet handler into function for IT context
callback. The logic to build IT packet header and tracepoints event is
split to a function.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The value of data block counter is not calculated for incoming packet
without CIP header. This commit fixes the bug.
Fixes: 947b437e12 ("ALSA: firewire-lib: unify packet handler for IR context")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In Linux firewire subsystem, for IT context, some quadlets of isochronous
packet payload can be indicated as a part of packet header to queue to
the context.
This commit uses the packet header to split CIP headers from CIP
payload. As a result, regardless of CIP or non-CIP, context payload
includes data blocks only.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a preparation to queue IT packet with header. To enable
packet handler to fill the header, this commit uses kernel stack for
data structure of packet parameter in several part of this file.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The handlers for packet with CIP and without CIP include common codes.
This commit unifies them and remove an member for pointer to callback
function from data structure.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is minor code refactoring to split a function to generate CIP
header.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Usage of 16 bytes IR context header allows to handle context payload by
the same code for with-CIP and without-CIP packets.
This commit unifies both handlers of with-CIP and without-CIP packets.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IR context, some quadlets of packet payload can be included into
context header. This is good for packet with CIP header because the
context payload buffer can includes data blocks only for with-CIP and
without-CIP pakets.
This commit uses 16 bytes IR context header for this purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A parser for CIP header in incoming packet is enough large.
This commit splits it into a helper function to better looks of packet
handler.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The value of pointer to payload buffer is computed in each packet
handler, however the pointer can be decided before call of packet
handler.
This commit adds an argument for the pointer to the packet handler to
reduce codes to compute for the pointer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In current packet handler, the length of payload is given as an argument
of callback function, however this value is just required to process
payload of transferred isoc packet, thus just for IR context.
This commit replaces the argument for payload of packet with the
argument of context header. As a result, the length of payload is
computed in packet handler for IR context.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is to distinguish variable of CIP header from variable of
isochronous context header.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IT context, header includes information of cycle to have processed
queued packet.
This commit uses the per-packet information to compute the cycle for
packet to be queued, instead of callback argument. In current
implementaion of ALSA IEC 61883-1/6 packet streaming engine, 48 packets
are queued at first to skip recent cycle. When IT context calls handler,
cycle information in header plus 48 cycle means the cycle to be going
to queue packet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The header size parameter of 1394 OHCI IT context has no effect.
Besides the header size of queued packet is different from context
header.
This commit cleans codes relevant to these two headers.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In callback handler of isochronous context for both direction, there're
common codes to cancel context.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some parameters of struct amdtp_stream is dependent on direction.
This commit uses union for such parameters to distinguish from
common parameters.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now four events of this module have the same arguments and probe timing.
This commit adds a new event, 'amdtp_packet', and replace them. Filtering
functionality of tracing framework is available to pick up events for
inbound/outbound isochronous packets.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This modules handles two types of isochronous packet; one has CIP header
in IEC 61883-1/6 and another doesn't. The module also have tracing events
corresponding to the types of packet. To unify the events, one event
should be probed with or without CIP header.
This commit uses dynamic array for the events to be available for the
types of packet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The most of tracing event in this module have the size of payload in
byte unit, however 'in_packet_without_header' event have the argument
in quadlet unit.
This commit change the unit for argument to be consistent.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tracing events for packets without CIP header have a parameter of
data_blocks/data_block_counter, but events for packets with CIP header
don't. This is not good to unify these events.
This commit adds the missing parameters to the events. In timing to
probe 'in_packet' event, data_blocks and data_block_counter are not
calculated yet. This commit also changes the timing.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
An argument for CIP header in 'in_packet' event is not the same type in
'out_packet' event. This is not good to unify these events.
This commit uses the same type of argument for these events.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In kernel API of Linux FireWire subsystem, handlers of isochronous
receive (IR) context can get context headers as an argument of
callback. When 4 byte header is used, the context header includes
isochronous packet header for each packet. When 8 byte header is
used, it includes isochronous cycle as well.
ALSA IEC 61883-1/6 engine uses 4 byte header, and computes isochronous
cycle from the cycle of interrupt. The usage of 8 byte header can
obsolete the computation.
Furthermore, this change works well for a case that a series of
packet in one interrupt includes skipped isochronous cycle,
This commit uses 8 byte header to handle isochronous cycle.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds support for MOTU 8pre FireWire, which was shipped 2007
and nowadays already discontinued. Userspace applications can transmit
and receive PCM frames and MIDI messages for this model via ALSA PCM
interface and RawMidi/Sequencer interfaces.
Like the other models of MOTU FireWire series, this model has many
quirks in its CIP.
At first, data channels for two pairs of optical interfaces. At lower
sampling transmission frequency, i.e. 44.1 and 48.0 kHz, one pair is
available for ADAT data, thus 8 data chunks are transferred by CIP.
At middle sampling transmission frequency, i.e. 88.2 and 96.0 kHz,
two pairs are available to keep 8 chunks for ADAT data, thus CIP
still includes 8 data chunks.
Apart from data chunks for optical interface, CIP includes fixed number
of data chunks. In tx stream, two chunks for status message, eight
chunks for samples from analog 1-8 input, two chunks for mix-return.
In rx stream, two chunks for control message, two chunks for main 1-2
output, two chunks for phone 1-2 output, two chunks for dummy 1-2.
CIP header in tx stream includes quirks for its dbs and dbc fields.
The value of dbs field is fixed to 0x13, against its actual size.
The value of dbc field is firstly updated to 0x07 from zero, then
it's incremented continuously according to actual number of data h
blocks.
Finally, the model has own bits to disable frame fetch.
This commit uses several options to absorb the above quirks.
$ python2 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 0410b57d bus_info_length 4, crc_length 16, crc 46461
404 31333934 bus_name "1394"
408 20001000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 1 (4)
40c 0001f200 company_id 0001f2 |
410 00083dfb device_id 0000083dfb | EUI-64 0001f20000083dfb
root directory
-----------------------------------------------------------------
414 0004c65c directory_length 4, crc 50780
418 030001f2 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 8d000006 --> eui-64 leaf at 438
424 d1000001 --> unit directory at 428
unit directory at 428
-----------------------------------------------------------------
428 0003991c directory_length 3, crc 39196
42c 120001f2 specifier id
430 1300000f version
434 17103800 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 00022681 leaf_length 2, crc 9857
43c 0001f200 company_id 0001f2 |
440 00083dfb device_id 0000083dfb | EUI-64 0001f20000083dfb
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current ALSA firewire-motu driver uses the value of 'model' field
of unit directory in configuration ROM for modalias for MOTU
FireWire models. However, as long as I checked, Pre8 and
828mk3(Hybrid) have the same value for the field (=0x100800).
unit | version | model
--------------- | --------- | ----------
828mkII | 0x000003 | 0x101800
Traveler | 0x000009 | 0x107800
Pre8 | 0x00000f | 0x100800 <-
828mk3(FW) | 0x000015 | 0x106800
AudioExpress | 0x000033 | 0x104800
828mk3(Hybrid) | 0x000035 | 0x100800 <-
When updating firmware for MOTU 8pre FireWire from v1.0.0 to v1.0.3,
I got change of the value from 0x100800 to 0x103800. On the other
hand, the value of 'version' field is fixed to 0x00000f. As a quick
glance, the higher 12 bits of the value of 'version' field represent
firmware version, while the lower 12 bits is unknown.
By induction, the value of 'version' field represents actual model.
This commit changes modalias to match the value of 'version' field,
instead of 'model' field. For degug, long name of added sound card
includes hexadecimal value of 'model' field.
Fixes: 6c5e1ac0e1 ("ALSA: firewire-motu: add support for Motu Traveler")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In data blocks of common isochronous packet for MOTU devices, PCM
frames are multiplexed in a shape of '24 bit * 4 Audio Pack', described
in IEC 61883-6. The frames are not aligned to quadlet.
For capture PCM substream, ALSA firewire-motu driver constructs PCM
frames by reading data blocks byte-by-byte. However this operation
includes bug for lower byte of the PCM sample. This brings invalid
content of the PCM samples.
This commit fixes the bug.
Reported-by: Peter Sjöberg <autopeter@gmail.com>
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 4641c93940 ("ALSA: firewire-motu: add MOTU specific protocol layer")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The calls of snd_info_register() are superfluous and should be avoided
at the procfs creation time. They are called at the end of the whole
initialization via snd_card_register(). This patch drops such
superfluous calls.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Duende Classic was produced by Solid State Logic in 2006, as a
first model of Duende DSP series. The following model, Duende Mini
was produced in 2008. They are designed to receive isochronous
packets for PCM frames via IEEE 1394 bus, perform signal processing by
downloaded program, then transfer isochronous packets for converted
PCM frames.
These two models includes the same embedded board, consists of several
ICs below:
- Texus Instruments Inc, TSB41AB3 for physical layer of IEEE 1394 bus
- WaveFront semiconductor, DICE II STD ASIC for link/protocol layer
- Altera MAX 3000A CPLD for programs
- Analog devices, SHARC ADSP-21363 for signal processing (4 chips)
This commit adds support for the two models to ALSA dice driver. Like
support for the other devices, packet streaming is just available.
Userspace applications should be developed if full features became
available; e.g. program uploader and parameter controller.
$ ./hinawa-config-rom-printer /dev/fw1
{ 'bus-info': { 'adj': False,
'bmc': False,
'chip_ID': 349771402425,
'cmc': True,
'cyc_clk_acc': 255,
'generation': 1,
'imc': True,
'isc': True,
'link_spd': 2,
'max_ROM': 1,
'max_rec': 512,
'name': '1394',
'node_vendor_ID': 20674,
'pmc': False},
'root-directory': [ ['VENDOR', 20674],
['DESCRIPTOR', 'Solid State Logic'],
['MODEL', 112],
['DESCRIPTOR', 'Duende board'],
[ 'NODE_CAPABILITIES',
{ 'addressing': {'64': True, 'fix': True, 'prv': True},
'misc': {'int': False, 'ms': False, 'spt': True},
'state': { 'atn': False,
'ded': False,
'drq': True,
'elo': False,
'init': False,
'lst': True,
'off': False},
'testing': {'bas': False, 'ext': False}}],
[ 'UNIT',
[ ['SPECIFIER_ID', 20674],
['VERSION', 1],
['MODEL', 112],
['DESCRIPTOR', 'Duende board']]]]}
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The > should be >= or otherwise we potentially read one element beyond
the end of the ff->tx_midi_substreams[] array.
Fixes: 73f5537fb2 ("ALSA: fireface: support tx MIDI functionality of Fireface UCX")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In Fireface series, registration of higher 4 bytes of destination
address for asynchronous transaction of MIDI messages is done by
a write transaction to model-specific register.
On the other hand, registration of lower 4 bytes of the address is
selectable from 4 options. A register for this registration includes
the other purpose options such as input attenuation. Thus this
driver expects userspace applications to configure the register.
Actual behaviour for the asynchronous transaction is different
depending on protocols. In former protocol, destination offset
of each transaction is the same as the registered address even if
it is block request. In latter models, destination offset of each
transaction is the offset of previous transaction plus 4 byte
and the transaction is quadlet request.
This commit cleanups comments about the above mechanism.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In latter model of Fireface series, asynchronous transaction includes
a prefix byte to indicate the way to decode included MIDI bytes.
Upper 4 bits of the prefix byte indicates port number, and the rest 4
bits indicate the way to decode rest of bytes for MIDI messages.
Basically the rest bits indicates the number of bytes for MIDI message.
However, if the last byte of each MIDi message is included, the rest
bits are 0xf. For example:
message: f0 00 00 66 14 20 00 00 f7
offset: content (big endian, port 0)
'0030: 0x02f00000
'0030: 0x03006614
'0030: 0x03200000
'0030: 0x0ff70000
This commit supports encoding scheme for the above and allows
applications to transfer MIDI messages via ALSA rawmidi interface.
An unused member (running_status) is reused to keep state of
transmission of system exclusive messages.
For your information, this is a dump of config rom.
$ sudo ./hinawa-config-rom-printer /dev/fw1
{ 'bus-info': { 'bmc': False,
'chip_ID': 13225063715,
'cmc': False,
'cyc_clk_acc': 0,
'imc': False,
'isc': True,
'max_rec': 512,
'name': '1394',
'node_vendor_ID': 2613},
'root-directory': [ [ 'NODE_CAPABILITIES',
{ 'addressing': {'64': True, 'fix': True, 'prv': False},
'misc': {'int': False, 'ms': False, 'spt': True},
'state': { 'atn': False,
'ded': False,
'drq': True,
'elo': False,
'init': False,
'lst': True,
'off': False},
'testing': {'bas': False, 'ext': False}}],
['VENDOR', 2613],
['DESCRIPTOR', 'RME!'],
['EUI_64', 2873037108442403],
[ 'UNIT',
[ ['SPECIFIER_ID', 2613],
['VERSION', 4],
['MODEL', 1054720],
['DESCRIPTOR', 'Fireface UCX']]]]}
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Between former and latter models, content of asynchronous transaction
for MIDI messages from driver to device is different.
This commit is a preparation to support latter models. A protocol-specific
operation is added to encode MIDI messages to the transaction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Between former and latter models, destination address to receive
asynchronous transactions for MIDI messages is different.
This commit adds model-dependent parameter for the addresses.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface UCX transfers asynchronous transactions for MIDI messages.
One transaction includes quadlet data therefore it can transfer 3
message bytes as maximum. Base address of the destination is
configured by two settings; a register for higher 8 byte of the
address, and a bitflag to option register indicates lower 8byte.
The register for higher address is 0x'ffff'0000'0034. Unfortunately,
firmware v24 includes a bug to ignore registered value for the
destination address and transfers to 0x0001xxxxxxxx always. This
driver doesn't work well if the bug exists, therefore users should
install the latest firmware (v27).
The bitflag is a part of value to be written to option register
(0x'ffff'0000'0014).
lower addr: bitflag (little endian)
'0000'0000: 0x00002000
'0000'0080: 0x00004000
'0000'0100: 0x00008000
'0000'0180: 0x00010000
This register includes more options but they are not relevant to
packet streaming or MIDI functionality. This driver don't touch it.
Furthermore, the transaction is sent to address offset incremented
by 4 byte to the offset in previous time. When it reaches base address
plus 0x7c, next offset is the base address.
Content of the transaction includes a prefix byte. Upper 4 bits of
the byte indicates port number, and the rest 4 bits indicate the way
to decode rest of bytes for MIDI message.
Except for system exclusive messages, the rest bits are the same as
status bits of the message without channel bits. For system exclusive
messages, the rest bits are encoded according to included message bytes.
For example:
message: f0 7e 7f 09 01 f7
offset: content (little endian, port 0)
'0000: 0x04f07e7f
'0004: 0x070901f7
message: f0 00 00 66 14 20 00 00 00 f7
offset: content (little endian, port 1)
'0014: 0x14f00000
'0018: 0x14661420
'001c: 0x14000000
'0020: 0x15f70000
message: f0 00 00 66 14 20 00 00 f7
offset: content (little endian, port 0)
'0078: 0x04f00000
'007c: 0x04661420
'0000: 0x070000f7
This commit supports decoding scheme for the above and allows
applications to receive MIDI messages via ALSA rawmidi interface.
The lower 8 bytes of destination address is fixed to 0x'0000'0000,
thus this driver expects userspace applications to configure option
register with bitflag 0x00002000 in advance.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In Fireface series, drivers can register destination address for
asynchronous transaction which transfers MIDI messages from device.
In former models, all of the transactions arrive at the registered
address without any offset. In latter models, each of the transaction
arrives at the registered address with sequential offset within 0x00
to 0x7f. This seems to be for discontinuity detection.
This commit adds model-dependent member for the address range.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a series of Fireface, devices transfer asynchronous transaction with
MIDI messages. In the transaction, content is different depending on
models. ALSA fireface driver has protocol-dependent handler to pick up
MIDI messages from the content.
In latter models of the series, the transaction is transferred to range
of address sequentially. This seems to check continuity of transferred
messages.
This commit changes prototype of the handler to receive offset of
address for received transactions.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface UFX was shipped by RME GmbH in 2012. This model supports later
protocol for management of isochronous communication and synchronization
of sampling transmission frequency.
This commit adds support for the model. At present, it's not clear how
to encode MIDI messages and decide destination address for asynchronous
transaction, thus this commit adds support for isochronous communication
for PCM frames only.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A procedure to retrieve clock configuration is used by two callers.
Each of caller has duplicated code to parse bits.
This commit adds refactoring to remove the duplicated code.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds refactoring for dump of sync status by adding
tables for check bits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a member for a callback function to get clock status
to former protocol.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a member for a callback function to switch frame
fetching mode to former protocol.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a member for a callback function to dump status and
move existing code to former protocol.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a series of Fireface, latter protocol has no way for drivers to
retrieve current clock configuration. On the other hand, this driver
has proc node for it.
This commit removes a proc node to dump both clock configuration
and synchronization status in one proc node.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit moves codes for Fireface 400 to a file of former protocol.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a series of Fireface, later model supports different protocol
from former models.
This commit is a preparation to support both of protocols.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As a result of investigation for Fireface 800, 'struct snd_ff_spec.regs'
is just for higher address to receive tx asynchronous packets of MIDI
messages, thus it can be simplified.
This commit simplifies it.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a functionality to multiplex PCM frames into isochronous
packets and demultiplex PCM frames from isochronous packets for ALSA PCM
applications.
Fireface 800 voluntarily maintains resources for tx isochronous
communication. It performs reservation of isochronous channel and
allocation/update of bandwidth in some cases below:
- at a first request to allocation after bus resets
- at requests to allocation when further bandwidth is required
When request is grant and the unit is prepared, read data from
0x0000801c0008 represents isochronous channel for tx stream, then
the unit can handle requests to start communication. If driver
send the request without checking the register, the unit takes
panic to continue bus resets. The unit starts transmission of
tx packets after receiving several rx packets from driver.
I note that the unit can process tx/rx packets and generate/record
sound regardless of HOST LED.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The way to maintain isochronous resources on bus is different between
Fireface 400/800.
This commit is a preparation. This commit moves a function to allocate resource to
model-dependent implementation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface 400/800 use three modes against the number of data channels in
data block for both tx/rx packets.
This commit adds refactoring for it. Some enumerators are added to
represent each of mode and a function is added to calculate the mode
from sampling frequency code (sfc).
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both of Fireface 400/800 have the same register to switch frame fetching
mode regardless of difference of available number of PCM frames in
rx isochronous packet.
This commit moves a helper function from model-dependent implementation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to my memo at hand and saved records, writing 0x00000001 to
SND_FF_REG_FETCH_PCM_FRAMES disables fetching PCM frames in corresponding
channel, however current implement uses reversed logic. This results in
muted volume in device side during playback.
This commit corrects the bug.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 76fdb3a9e1 ('ALSA: fireface: add support for Fireface 400')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
An initial commit to add tracepoints for packets without CIP headers
uses different print formats for added tracepoints. However this is not
convenient for users/developers to prepare debug tools.
This commit uses the same format for the two tracepoints.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: b164d2fd6e ('ALSA: firewire_lib: add tracepoints for packets without CIP headers')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
An initial commit to add tracepoints for packets without CIP headers
introduces a wrong assignment to 'data_blocks' value of
'out_packet_without_header' tracepoint.
This commit fixes the bug.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: b164d2fd6e ('ALSA: firewire_lib: add tracepoints for packets without CIP headers')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-1/6 engine of ALSA firewire stack, a packet handler has a
second argument for 'the number of bytes in payload of isochronous
packet'. However, an incoming packet handler without CIP header uses the
value as 'the number of quadlets in the payload'. This brings userspace
applications to receive the number of PCM frames as four times against
real time.
This commit fixes the bug.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 3b196c394d ('ALSA: firewire-lib: add no-header packet processing')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface 800 is a flagship model of RME GmbH for audio and music units
on IEEE 1394 bus, shipped 2004. This model consists of four chips:
- TI TSB81BA3D for physical layer on cable environment of EEE 1394 bus
- TI TSB82AA2 for link layer for 1394 OHCI bus bridge to PCI bus
- Xilinx Spartan-3 FPGA XC3S400
- Xilinx High-Performance CPLD XC9572XL
This commit adds support Fireface 800. In this time, the support is
restricted to its MIDI functionality, thus this commit adds some
condition statements to avoid touching streaming functionality.
Unlike Fireface 400, Fireface 800 has no functionality to suppress
asynchronous transactions for MIDI messages except for unregister of
listen address in controller side, thus the feature is available as is.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Content of asynchronous transaction for MIDI messages differs between
Fireface 400 and 800.
This commit adds a model-specific handler for the transaction and adds
arrangement.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface 400 and 800 have the same mechanism to decide address to which
asynchronous transactions are sent for MIDI messages, however they use
different registers for controllers to notify higher 4 byte of the
address.
This commit adds a model-specific parameter to represent the address.
Additionally, it corrects some comments. I note that these two models have
a difference to enable/disable the transaction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating packet dumps from Fireface 400/800, a register
to receive asynchronous transactions for MIDI messages is the same. For
Fireface 800, minor register is used.
This commit declares macros for the transactions and obsoletes
model-specific parameters.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unlike Fireface 400, Fireface 800 have two pair of optical interface
for ADAT signal and S/PDIF signal. ADAT signals for the interface
are handled for sampling clock source separately.
This commit modifies a parser for clock configuration to distinguish
these two ADAT signals.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating packet dumps from Fireface 400/800, bits on
status registers for clock synchronization are the same.
This commit moves a parser for a register of clock configuration to
obsolete model-specific operations.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating packet dumps from Fireface 400/800, bits on
status registers for clock synchronization are the same.
This commit moves a parser for the registers to obsolete model-specific
operations.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating packet dumps from Fireface 400/800, status
registers for clock synchronization is common.
This commit moves some macros for them to header file.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In an initial commit, 'SYNC_STATUS' register is referred to get
clock configuration, however this is wrong, according to my local
note at hand for reverse-engineering about packet dump. It should
be 'CLOCK_CONFIG' register. Actually, ff400_dump_clock_config()
is correctly programmed.
This commit fixes the bug.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 76fdb3a9e1 ('ALSA: fireface: add support for Fireface 400')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commits, ALSA firewire-tascam driver queues events to notify
change of state of control surface to userspace via ALSA hwdep
interface.
This commit implements actual notification of the events. The events are
not governed by real time, thus no need to care underrun.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In later commits, ALSA firewire-tascam driver will allow userspace
applications to receive notifications about changes of device state,
transferred in tx isochronous packet. At present, all of drivers in ALSA
firewire stack have mechanism to notify change of status of packet
streaming, thus it needs to distinguish these two types of notification.
This commit is a preparation for the above.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Units of TASCAM FireWire series transfer image of states of the unit in
tx isochronous packets. Demultiplexing of the states from the packets
is done in software interrupt context regardless of any process context.
In a view of userspace applications, it needs to have notification
mechanism to catch change of the states.
This commit implements a queue to store events for the notification. The
image of states includes fluctuating data such as level of gain/volume
for physical input/output and position of knobs. Therefore the events
are queued corresponding to some control features only.
Furthermore, the queued events are planned to be consumed by userspace
applications via ALSA hwdep interface. This commit suppresses event
queueing when no applications open the hwdep interface.
However, the queue is maintained in an optimistic scenario, thus without
any care against overrrun. This is reasonable because target events are
useless just to handle PCM frames. It starts queueing when an usespace
application opens hwdep interface, thus it's expected to read the queued
events steadily.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a previous commit, ALSA firewire-tascam driver stores state image
from tx isochronous packets. This image includes states of knob, fader,
button of control surface, level of gain/volume of each physical
inputs/outputs, and so on. It's useful for userspace applications to
read whole of the image.
This commit adds a unique ioctl command for ALSA hwdep interface for the
purpose. For actual meaning of each bits in this image, please refer to
discussion in alsa-devel[1].
[1] http://mailman.alsa-project.org/pipermail/alsa-devel/2018-October/140785.html
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Units of TASCAM FireWire series multiplex PCM frames and state of
control surface into the same tx isochronous packets. One isochronous
packet includes a part of the state in a quadlet data. An image of the
state consists of 64 quadlet data.
This commit demultiplexes the state from tx isochronous packets.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a former commit, PCM constraint based on LCM of SYT_INTERVAL was
obsoleted with PCM rule. However, the new PCM rule brings -EINVAL in
some cases that max/min values of size of buffer/period is not
multiples of one of values of SYT_INTERVAL. For example, pulseaudio
always fail to configure PCM substream.
This commit changes strategy for the PCM rule. Although the buggy rules
had a single dependency (rate from period, period from rate, rate from
buffer, buffer from rate), a revised rule has double dependencies
(period from period/rate, buffer from buffer/rate). A step of value is
calculated with table of SYT_INTERVAL and list of available rates. This
prevents interval template which brings -EINVAL to a call of
snd_interval_refine().
Fixes: 5950229582bc('ALSA: firewire-lib: add PCM rules to obsolete PCM constraints based on LCM of SYT_INTERVAL')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a development period for Linux kernel v4.20, drivers in ALSA firewire
stack were changed to wait for releases of all ALSA character devices at
.remove callback of bus driver. However, ALSA dice driver is partly out
of this change. This bug can bring fault to user process which holds
the last of character device in unplugging.
This commit fixes the driver to wait in the callback.
Fixes: 61ccc6f6b2 ('ALSA: firewire: block .remove callback of bus driver till all of ALSA character devices are released')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In some error paths, reference count of firewire unit is not decreased.
This commit fixes the bug.
Fixes: 5b14ec25a79b('ALSA: firewire: release reference count of firewire unit in .remove callback of bus driver')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commits, .private_free callback releases resources just for
data transmission. This release function can be called without the
resources are actually allocated in error paths.
This commit applies a small refactoring to clean up codes in error
paths.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In drivers of ALSA firewire stack, bebob and fireworks drivers have
local device entry table. At present, critical section to operate the
table is from the beginning/end of 'do_registration' call. This can be
more narrow and simplify codes.
This commit applies small refactoring for the above purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a previous commit, drivers in ALSA firewire stack blocks .remove
callback of bus driver. This enables to release members of private
data in the callback after releasing device of sound card.
This commit simplifies codes to release the members.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At present, in .remove callback of bus driver just decrease reference
count of device for ALSA card instance. This delegates release of the
device to a process in which the last of ALSA character device is
released.
On the other hand, the other drivers such as for devices on PCIe are
programmed to block .remove callback of bus driver till all of ALSA
character devices are released.
For consistency of behaviour for whole drivers, this probably confuses
users. This commit takes drivers in ALSA firewire stack to imitate the
above behaviour.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA oxfw driver allocates memory objects for cache of stream formats.
The objects are used to maintain packet streaming by components for
ALSA rawMIDI/PCM interface. They can be released as managed-resource
of 'struct snd_card.card_dev'.
This commit uses managed-resource of the sound card device for this
purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA oxfw driver allocates memory objects for data specific to some
models. These objects are used to maintain functionalities specific
to the models for ALSA rawMIDI/control interfaces. They can be
released as managed-resource of 'struct snd_card.card_dev'.
This commit uses managed-resource of the sound card device for this
purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA fireworks driver allocates memory object to handle response from
target unit. The object is used to initiate transaction unique to
Fireworks board module. This can be released as managed-resource
of 'struct snd_card.card_dev'.
This commit uses managed-resource of the sound card device for this
purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA bebob driver allocates memory object for data specific to M-Audio
FW-1884/ProjectMix I/O. The object is to maintain format of isochronous
packet payload for packet streaming by components for ALSA rawMIDI/PCM
interfaces. The object can be released as managed-resource of
'struct snd_card.card_dev'.
This commit uses managed-resource of the sound card device for this
purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At present, private data of each driver in ALSA firewire stack is
allocated/freed by kernel slab allocator for corresponding unit on
IEEE 1394 bus. In this case, resource-managed slab allocator is
available to release memory object automatically just before releasing
device structure for the unit. This idea can prevent runtime from
memory leak due to programming mistakes.
This commit uses the allocator for the private data. These drivers
already use reference counter to maintain lifetime of device structure
for the unit by a pair of fw_unit_get()/fw_unit_put(). The private data
is safely released in a callback of 'struct snd_card.private_free().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In blocking mode of IEC 61883-1/6, when one isochronous packet includes
data for events, the data is for the same number of events as
SYT_INTERVAL decided according to sampling transmission frequency (SFC).
IEC 61883-1/6 engine of ALSA firewire stack applies constraints of
period and buffer size of PCM intermediate buffer of PCM substream.
At present, this constraint is designed to round the size up/down to
32 frames. This value comes from the least common multiple (LCM) of
SYT_INTERVAL. Although this looks to work well, in lower sampling
rate, applications are not allowed to set size of period quite near
period time constraint (at present 5 msec per period).
This commit adds PCM rules for period/buffer size and rate to obsoletes
the constraints based on LCM.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After allocating memory object for response buffer, ALSA fireworks
driver has leak of the memory object at error path.
This commit releases the object at the error path.
Fixes: 7d3c1d5901aa('ALSA: fireworks: delayed registration of sound card')
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After finishing discover of stream formats, ALSA OXFW driver has memory
leak of allocated memory object at error path.
This commit releases the memory object at the error path.
Fixes: 6c29230e2a ('ALSA: oxfw: delayed registration of sound card')
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After allocating model-dependent data, ALSA OXFW driver has memory leak
of the data at error path.
This commit releases the data at the error path.
Fixes: 6c29230e2a ('ALSA: oxfw: delayed registration of sound card')
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After allocating model-dependent data for M-Audio FW1814 and ProjectMix
I/O, ALSA bebob driver has memory leak at error path.
This commit releases the allocated data at the error path.
Fixes: 04a2c73c97eb('ALSA: bebob: delayed registration of sound card')
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although private data of sound card instance is usually allocated in the
tail of the instance, drivers in ALSA firewire stack allocate the private
data before allocating the instance. In this case, the private data
should be released explicitly at .private_free callback of the instance.
This commit fixes memory leak following to the above design.
Fixes: 6c29230e2a ('ALSA: oxfw: delayed registration of sound card')
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although private data of sound card instance is usually allocated in the
tail of the instance, drivers in ALSA firewire stack allocate the private
data before allocating the instance. In this case, the private data
should be released explicitly at .private_free callback of the instance.
This commit fixes memory leak following to the above design.
Fixes: b610386c8a ('ALSA: firewire-tascam: deleyed registration of sound card')
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although private data of sound card instance is usually allocated in the
tail of the instance, drivers in ALSA firewire stack allocate the private
data before allocating the instance. In this case, the private data
should be released explicitly at .private_free callback of the instance.
This commit fixes memory leak following to the above design.
Fixes: 86c8dd7f4d ('ALSA: firewire-digi00x: delayed registration of sound card')
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When executing 'fw_run_transaction()' with 'TCODE_WRITE_BLOCK_REQUEST',
an address of 'payload' argument is used for streaming DMA mapping by
'firewire_ohci' module if 'size' argument is larger than 8 byte.
Although in this case the address should not be on kernel stack, current
implementation of ALSA bebob driver uses data in kernel stack for a cue
to boot M-Audio devices. This often brings unexpected result, especially
for a case of CONFIG_VMAP_STACK=y.
This commit fixes the bug.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=201021
Reference: https://forum.manjaro.org/t/firewire-m-audio-410-driver-wont-load-firmware/51165
Fixes: a2b2a7798fb6('ALSA: bebob: Send a cue to load firmware for M-Audio Firewire series')
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A commit 28b208f600 ('ALSA: dice: add parameters of stream formats for
models produced by Alesis') adds wrong copy to rx parameters instead of
tx parameters for Alesis iO26.
This commit fixes the bug for v4.18-rc8.
Fixes: 28b208f600 ('ALSA: dice: add parameters of stream formats for models produced by Alesis')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # v4.18
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_pcm_lib_mmap_vmalloc() was supposed to be implemented with
somewhat special for vmalloc handling, but in the end, this turned to
just the default handler, i.e. NULL. As the situation has never
changed over decades, let's rip it off.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds support for MOTU Traveler, launched in 2005, discontinued
quite before. As a result, transmission of PCM frame and MIDI messages is
available via ALSA PCM and RawMIDI/Sequencer interfaces.
This model supports sampling transmission frequency up to 192.0 kHz, and
AES/EBU on XLR interface and ADAT on optical interface. Unlike
Motu 828MkII, Windows driver can switch fetching mode for DSP, like
mute/unmute feature.
Although this commit enables high sampling transmission frequency, actual
sound from this model is not good. As long as I tested, it's silence at
176.4 kHz, and it includes hissing noise at 192.0 kHz. In my opinion, as I
reported at 3526ce7f9ba7 ('ALSA: firewire-motu: add MOTU specific protocol
layer'), timestamping on source packet header (SPH) may not still be good
for this model as well.
$ python2 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 04106505 bus_info_length 4, crc_length 16, crc 25861
404 31333934 bus_name "1394"
408 20001000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 1 (4)
40c 0001f200 company_id 0001f2 |
410 0001f32f device_id 000001f32f | EUI-64 0001f2000001f32f
root directory
-----------------------------------------------------------------
414 0004c65c directory_length 4, crc 50780
418 030001f2 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 8d000006 --> eui-64 leaf at 438
424 d1000001 --> unit directory at 428
unit directory at 428
-----------------------------------------------------------------
428 00035955 directory_length 3, crc 22869
42c 120001f2 specifier id
430 13000009 version
434 17107800 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 000206b2 leaf_length 2, crc 1714
43c 0001f200 company_id 0001f2 |
440 0001f32f device_id 000001f32f | EUI-64 0001f2000001f32f
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For MOTU protocol version 2, this driver arranges the number of data
chunks to align chunks to quadlet data channel. However, MOTU Traveler
has padding bytes in the end of data block at high clock mode.
This commit removes the arrangement. Fortunately, at low and middle clock
mode, supported model for v2 protocol (828mkII) gets no influence from this
change because all of combination for data chunks are just aligned to
quadlet data channel.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU Traveler supports AES/EBU on XLR interface and data block of rx/tx
packet includes two chunk for the interface. This commit adds a flag
for this purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver explicitly assumes that all of supported models have main data
chunk separated from chunk for analog ports. However, MOTU Traveler doesn't
support the separated main data chunk.
This commit adds a flag for the separated main data chunk.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In MOTU firewire protocol, data block consists of 24 bit data chunks except
for one quadlet for source packet header (SPH). The number of data chunk in
a data block is different between three clock modes; low, middle and high.
When unit supports ADAT on optical interface, the data block includes some
chunks for ADAT channels. These ADAT chunks are unavailable at high mode.
This driver has local functions to calculate the number of ADAT chunks. But
They uses stack for three clock modes. This is useless for higher mode.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert the S_<FOO> symbolic permissions to their octal equivalents as
using octal and not symbolic permissions is preferred by many as more
readable.
see: https://lkml.org/lkml/2016/8/2/1945
Done with automated conversion via:
$ ./scripts/checkpatch.pl -f --types=SYMBOLIC_PERMS --fix-inplace <files...>
Miscellanea:
o Wrapped one multi-line call to a single line
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At present, all of models produced by TC Electronic except for Konnekt Live
are supported with hard-coded their stream formats. Studio Konnekt 48 is
sore model to support dual streams for both directions. The second stream
has no MIDI conformant data channel in its data block. But current
implementation transfers the second stream with MIDI conformant data
channel.
This commit fixes this issue.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
match_string() returns the index of an array for a matching string,
which can be used intead of open coded variant.
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The "entry" pointer is always non-NULL so this test for out of bounds
won't work.
Fixes: f1f0f330b1 ("ALSA: dice: add parameters of stream formats for models produced by TC Electronic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
--nextPart3916812.EicPReet6m
Content-Transfer-Encoding: 7Bit
Content-Type: text/plain; charset="us-ascii"
Mytek manufactures some equipment with DICE-based firewire ports. These
devices contain old versions of DICE firmware which lacks detailed
stream format reporting for all sampling clock modes.
Building upon the recent work by Takashi Sakamoto, hard-coded parameters
are added for the Stereo 192 DSD-DAC. When the device vendor and model
match the coded parameters are copied into the stream format cache.
Signed-off-by: Melvin Vermeeren <mail@mel.vin>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A series of SNDRV_CTL_TLVO_XXX macro was introduced for position offset
of TLV data. This commit applies a code optimization.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At present, to add PCM substreams for each of available tx/rx streams,
this driver uses a condition based on model-name. This is not enough
to support unknown models.
In former commits, this driver gains cache of stream formats. For models
which support protocol extension, all of available steam formats are
cached. For known models, hard-coded stream formats are used to generate
the cache. For unknown models, stream formats at current mode of sampling
transmission frequency is cached.
Anyway, at least, the cached formats are used to expose constrains of PCM
substreams for userspace applications. Thus, The cached data can be also
used to add PCM substreams themselves, instead of the name-based
conditions.
This commit obsoletes local frag of force_two_pcms.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commits, proxy structure gets members for cache of stream
formats. The cache allows to apply correct constraints and rules to
runtime of PCM substream. They allows userspace applications to change
current sampling transmission frequency.
This commit uses the cacher for the PCM constraints and rules.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commits, proxy structure gets members for cache of stream
formats. The cache can be used to count the number of MIDI substreams
to add.
This commit uses the cache for this purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a preparation for userspace applications to change current sampling
transmission frequency via ALSA PCM interface.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a small refactoring for better readability.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At present, to check running stream, available stream formats are used
at current sampling transmission frequency (stf). But when changing stf,
it's convenient to use cache of stream formats.
This commit applies this idea.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TC Applied Technologies (TCAT) have added extension to DICE protocol. This
protocol extension is called as Extended Application Protocol, a.k.a. EAP.
In this protocol extension, units get additional 9 address spaces. One of
it is for current configuration. In this address space, a pair of router
and stream formats are exposed per mode of three sampling transmission
frequencies.
This commit adds support the protocol extension for address space of the
current configuration to generate cache of stream formats.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Alesis shipped some models with DICE ASICs. All of them just support
DICE original protocol and drivers can't retrieve all of available stream
formats without changing status of sampling transmission frequency
actually.
This commit puts some hard-coded parameters for the models. When detecting
the models, the corresponding parameters are copied as cache of stream
formats.
I note that each of pair of iO14/iO26 and MultiMix 8/12/16 has the same
model ID on their configuration ROM. The MultiMix 8/12/16 just support
one mode for sampling transmission frequency and ALSA dice driver already
handles them correctly. The iO14/iO26 support three modes and need
hard-coded parameters. To distinguish these two models, this commit let
the driver to retrieve current stream formats and compare it to known
parameters, then decide it.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TC Electronic shipped some models with DICE ASICs. All of them just support
DICE original protocol and drivers can't retrieve all of available stream
formats without changing status of sampling transmission frequency
actually.
This commit puts some hard-coded parameters for the models. When detecting
the models, the corresponding parameters are copied as cache of stream
formats.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commits, proxy structure get members for cache of stream
formats. This commit fills the cache with stream formats at current mode
of sampling transmission frequency.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Products with DICE interface in market can support variable stream
formats for three levels of sampling transmission frequencies. To
record these formats, a proxy structure got several fields in former
commit.
This commit adds a proc node to output the stream formats for debugging
purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unlike the other drivers in ALSA firewire stack, ALSA dice driver does't
create 'firewire' directory for proc nodes because it has 'dice' node
only. But this is inconvenient because I have a plan to add another proc
node to output available stream formats from cache.
This commit let the driver to create the directory and put 'dice' node
into it.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A previous commit 6f688268b3 ('ALSA: dice: purge generating channel
cache') purged cache of stream formats. DICE interface originally has
no feature to assist drivers to retrieve available formats for all of
supported sampling transmission frequencies, without changing the
frequency actually.
For later release of Dice ASICs such as TCD2210, Dice interface has
extended protocol and can support the feature. This assists drivers
to retrieve available stream formats.
This commit is a first step to regain the cache to generate PCM rules
for all of supported sampling transmission frequencies.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At a commit f91c9d7610 ('ALSA: firewire-lib: cache maximum length of
payload to reduce function calls'), maximum size of payload for tx
isochronous packet is cached to reduce the number of function calls.
This cache was programmed to updated at a first callback of ohci1394 IR
context. However, the maximum size is required to queueing packets before
starting the isochronous context.
As a result, the cached value is reused to queue packets in next time to
starting the isochronous context. Then the cache is updated in a first
callback of the isochronous context. This can cause kernel NULL pointer
dereference in a below call graph:
(sound/firewire/amdtp-stream.c)
amdtp_stream_start()
->queue_in_packet()
->queue_packet()
(drivers/firewire/core-iso.c)
->fw_iso_context_queue()
->struct fw_card_driver.queue_iso()
(drivers/firewire/ohci.c)
= ohci_queue_iso()
->queue_iso_packet_per_buffer()
buffer->pages[page]
The issued dereference occurs in a case that:
- target unit supports different stream formats for sampling transmission
frequency.
- maximum length of payload for tx stream in a first trial is bigger
than the length in a second trial.
In this case, correct number of pages are allocated for DMA and the 'pages'
array has enough elements, while index of the element is wrongly calculated
according to the old value of length of payload in a call of
'queue_in_packet()'. Then it causes the issue.
This commit fixes the critical bug. This affects all of drivers in ALSA
firewire stack in Linux kernel v4.12 or later.
[12665.302360] BUG: unable to handle kernel NULL pointer dereference at 0000000000000030
[12665.302415] IP: ohci_queue_iso+0x47c/0x800 [firewire_ohci]
[12665.302439] PGD 0
[12665.302440] P4D 0
[12665.302450]
[12665.302470] Oops: 0000 [#1] SMP PTI
[12665.302487] Modules linked in: ...
[12665.303096] CPU: 1 PID: 12760 Comm: jackd Tainted: P OE 4.13.0-38-generic #43-Ubuntu
[12665.303154] Hardware name: /DH77DF, BIOS KCH7710H.86A.0069.2012.0224.1825 02/24/2012
[12665.303215] task: ffff9ce87da2ae80 task.stack: ffffb5b8823d0000
[12665.303258] RIP: 0010:ohci_queue_iso+0x47c/0x800 [firewire_ohci]
[12665.303301] RSP: 0018:ffffb5b8823d3ab8 EFLAGS: 00010086
[12665.303337] RAX: ffff9ce4f4876930 RBX: 0000000000000008 RCX: ffff9ce88a3955e0
[12665.303384] RDX: 0000000000000000 RSI: 0000000034877f00 RDI: 0000000000000000
[12665.303427] RBP: ffffb5b8823d3b68 R08: ffff9ce8ccb390a0 R09: ffff9ce877639ab0
[12665.303475] R10: 0000000000000108 R11: 0000000000000000 R12: 0000000000000003
[12665.303513] R13: 0000000000000000 R14: ffff9ce4f4876950 R15: 0000000000000000
[12665.303554] FS: 00007f2ec467f8c0(0000) GS:ffff9ce8df280000(0000) knlGS:0000000000000000
[12665.303600] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[12665.303633] CR2: 0000000000000030 CR3: 00000002dcf90004 CR4: 00000000000606e0
[12665.303674] Call Trace:
[12665.303698] fw_iso_context_queue+0x18/0x20 [firewire_core]
[12665.303735] queue_packet+0x88/0xe0 [snd_firewire_lib]
[12665.303770] amdtp_stream_start+0x19b/0x270 [snd_firewire_lib]
[12665.303811] start_streams+0x276/0x3c0 [snd_dice]
[12665.303840] snd_dice_stream_start_duplex+0x1bf/0x480 [snd_dice]
[12665.303882] ? vma_gap_callbacks_rotate+0x1e/0x30
[12665.303914] ? __rb_insert_augmented+0xab/0x240
[12665.303936] capture_prepare+0x3c/0x70 [snd_dice]
[12665.303961] snd_pcm_do_prepare+0x1d/0x30 [snd_pcm]
[12665.303985] snd_pcm_action_single+0x3b/0x90 [snd_pcm]
[12665.304009] snd_pcm_action_nonatomic+0x68/0x70 [snd_pcm]
[12665.304035] snd_pcm_prepare+0x68/0x90 [snd_pcm]
[12665.304058] snd_pcm_common_ioctl1+0x4c0/0x940 [snd_pcm]
[12665.304083] snd_pcm_capture_ioctl1+0x19b/0x250 [snd_pcm]
[12665.304108] snd_pcm_capture_ioctl+0x27/0x40 [snd_pcm]
[12665.304131] do_vfs_ioctl+0xa8/0x630
[12665.304148] ? entry_SYSCALL_64_after_hwframe+0xe9/0x139
[12665.304172] ? entry_SYSCALL_64_after_hwframe+0xe2/0x139
[12665.304195] ? entry_SYSCALL_64_after_hwframe+0xdb/0x139
[12665.304218] ? entry_SYSCALL_64_after_hwframe+0xd4/0x139
[12665.304242] ? entry_SYSCALL_64_after_hwframe+0xcd/0x139
[12665.304265] ? entry_SYSCALL_64_after_hwframe+0xc6/0x139
[12665.304288] ? entry_SYSCALL_64_after_hwframe+0xbf/0x139
[12665.304312] ? entry_SYSCALL_64_after_hwframe+0xb8/0x139
[12665.304335] ? entry_SYSCALL_64_after_hwframe+0xb1/0x139
[12665.304358] SyS_ioctl+0x79/0x90
[12665.304374] ? entry_SYSCALL_64_after_hwframe+0x72/0x139
[12665.304397] entry_SYSCALL_64_fastpath+0x24/0xab
[12665.304417] RIP: 0033:0x7f2ec3750ef7
[12665.304433] RSP: 002b:00007fff99e31388 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[12665.304465] RAX: ffffffffffffffda RBX: 00007fff99e312f0 RCX: 00007f2ec3750ef7
[12665.304494] RDX: 0000000000000000 RSI: 0000000000004140 RDI: 0000000000000007
[12665.304522] RBP: 0000556ebc63fd60 R08: 0000556ebc640560 R09: 0000000000000000
[12665.304553] R10: 0000000000000001 R11: 0000000000000246 R12: 0000556ebc63fcf0
[12665.304584] R13: 0000000000000000 R14: 0000000000000007 R15: 0000000000000000
[12665.304612] Code: 01 00 00 44 89 eb 45 31 ed 45 31 db 66 41 89 1e 66 41 89 5e 0c 66 45 89 5e 0e 49 8b 49 08 49 63 d4 4d 85 c0 49 63 ff 48 8b 14 d1 <48> 8b 72 30 41 8d 14 37 41 89 56 04 48 63 d3 0f 84 ce 00 00 00
[12665.304713] RIP: ohci_queue_iso+0x47c/0x800 [firewire_ohci] RSP: ffffb5b8823d3ab8
[12665.304743] CR2: 0000000000000030
[12665.317701] ---[ end trace 9d55b056dd52a19f ]---
Fixes: f91c9d7610 ('ALSA: firewire-lib: cache maximum length of payload to reduce function calls')
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In error path of snd_dice_stream_init_duplex(), stream data for incoming
packet can be left to be initialized.
This commit fixes it.
Fixes: 436b5abe22 ('ALSA: dice: handle whole available isochronous streams')
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In early stage of firmware SDK, DICE seems to lose its backward
compatibility due to some registers on global address section. I found
this with Alesis Multimix 12 FireWire with ancient firmware (approx.
shipped version).
According to retrieved log from the unit, global section has 96 byte
space. On the other hand, current version of ALSA dice driver assumes
that all of supported unit has at least 100 byte space.
$ ./firewire-request /dev/fw1 read 0xffffe0000000 28
result: 000: 00 00 00 0a 00 00 00 18 00 00 00 22 00 00 00 8a
result: 010: 00 00 00 ac 00 00 01 12 00 00 00 00 00 00 00 00
result: 020: 00 00 00 00 00 00 00 00
This commit adds support for the ancient firmware. Check of global section
is loosened to accept the smaller space. The lack of information is
already compensated by hard-coded parameters.
I experienced that the latest version of Windows driver for this model
can't handle this unit, too. This means that TCAT releases firmware SDK
without backward compatibility for the ancient firmware.
Below list is a early history of driver/firmware package released by
Alesis. I investigated on wayback machine on Internet Archive:
* Unknown: PAL v1.0.41.2, firmware v1.0.3
* Mar 2006: PAL v1.54.0, firmware v1.0.4
* Dec 2006: PAL v2.0.0.2, firmware v2.0
* Jun 2007: PAL v3.0.41.5, firmware v2.0
* Jul 2007: PAL v3.0.56.2. firmware v2.0
* Jan 2008: PAL v3.0.81.1080, firmware v2.0
If I can assume that firmware version is the same as DICE version, DICE
version for the issued firmware may be v1.0.3. According to code base of
userspace driver project (FFADO), I can read DICE v1.0.4 supports global
space larger than 100 byte. I guess the smaller space of global section is
a feature of DICE v1.0.3.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
OUI for TC Electronic is 0x000166, for TC GROUP A/S. 0x001486 is for Echo
Digital Audio Corporation.
Fixes: 7cafc65b3a ('ALSA: dice: force to add two pcm devices for listed models')
Cc: <stable@vger.kernel.org> # v4.6+
Reference: http://standards-oui.ieee.org/oui/oui.txt
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- fix trace_hfi1_ctxt_info() to pass large struct by reference instead of by value
- convert 'type array[]' tracepoint arguments into 'type *array',
since compiler will warn that sizeof('type array[]') == sizeof('type *array')
and later should be used instead
The CAST_TO_U64 macro in the later patch will enforce that tracepoint
arguments can only be integers, pointers, or less than 8 byte structures.
Larger structures should be passed by reference.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add a jump target so that a bit of exception handling can be better reused
at the end of this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a jump target so that a bit of exception handling can be better reused
at the end of this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Drivers in ALSA firewire stack still includes some symbols which can be
moved to a section for read-only symbols.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU Audio Express is one of third generation in MOTU FireWire
series, produced in 2011. This model consists of three chips:
* TI TSB41AB2 (Physical layer for IEEE 1394 bus)
* Microchip USB3300 (Hi-Speed USB Device with ULPI interface)
* Xilinx Spartan-3A FPGA, XC3S400A (Link layer for IEEE 1394 bus, packet
processing and data block processing layer)
This commit adds support for this model. As I expected, it works with
current implementaion of protocol version 3. On the other hand, the unit
has a quirk to request subaction originated by any driver.
11:45:51.287643 firewire_ohci 0000:03:00.0: AT spd 2 tl 1f, ffc1 -> ffc0, -reserved-, QW req, fffff0000b14 = 02000200
11:45:51.289193 firewire_ohci 0000:03:00.0: AR spd 2 tl 1f, ffc0 -> ffc1, ack_complete, W resp
11:45:51.289381 fireire_core 0000:03:00.0: unsolicited response (source ffc0, tlabel 1f)
11:45:51.313071 firewire_ohci 0000:03:00.0: AT spd 2 tl 20, ffc1 -> ffc0, ack_pending , QW req, fffff0000b14 = 02000200
11:45:51.314539 firewire_ohci 0000:03:00.0: AR spd 2 tl 20, ffc0 -> ffc1, ack_complete, W resp
In 1394 OHCI (rev.1.1), after OUTPUT_LAST* descriptors is processed,
'xferStaus' field is filled with 'ContextControl[0:15]' (see clause 7.1.3).
5 bits in LSB side of the field has ack code in acknowledge from the unit
(see clause 7.2.2). A list of the code is shown in Table 3-2.
As long as I investigated, in a case of the '-reserved-' acknowledge
message from the unit, the field has 0x10. On the table, this value is
'Reserved for definition by future 1394 standards'. As long as I know,
any specifications of IEEE 1394 has no such extensions, thus the unit is
out of specification. Besides, I note that the unit does not always
acknowledge with the invalid code. I guess this is a bug of firmware. I
confirmed the bug in firmware version 1.04 and this is the latest one.
$ cd linux-firewire-utils
$ python2 ./src/crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 0410a756 bus_info_length 4, crc_length 16, crc 42838
404 31333934 bus_name "1394"
408 20ff7000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 255, max_rec 7 (256)
40c 0001f200 company_id 0001f2 |
410 000a8a7b device_id 00000a8a7b | EUI-64 0001f200000a8a7b
root directory
-----------------------------------------------------------------
414 0004ef04 directory_length 4, crc 61188
418 030001f2 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 d1000002 --> unit directory at 428
424 8d000005 --> eui-64 leaf at 438
unit directory at 428
-----------------------------------------------------------------
428 00031680 directory_length 3, crc 5760
42c 120001f2 specifier id
430 13000033 version
434 17104800 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 00025ef3 leaf_length 2, crc 24307
43c 0001f200 company_id 0001f2 |
440 000a8a7b device_id 00000a8a7b | EUI-64 0001f200000a8a7b
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In protocols of MOTU FireWire series, when transferring MIDI messages,
transmitter set existence flag to one byte on first several quadlets. The
position differs depending on protocols and models, however two cases are
confirmed; in 5th byte and 8th byte from MSB side.
This commit adds a series of specification flag to describe them. When
the existence flag is in the 5th byte, SND_MOTU_SPEC_[R|T]X_MIDI_2ND_Q is
used. Else, another set of the flag is used. Here, '_Q' means quadlet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When calling 'iso_resource_free()' for uninitialized data, this function
causes NULL pointer dereference due to its 'unit' member. This occurs when
unplugging audio and music units on IEEE 1394 bus at failure of card
registration.
This commit fixes the bug. The bug exists since kernel v4.5.
Fixes: 324540c4e0 ('ALSA: fireface: postpone sound card registration') at v4.12
Fixes: 8865a31e0f ('ALSA: firewire-motu: postpone sound card registration') at v4.12
Fixes: b610386c8a ('ALSA: firewire-tascam: deleyed registration of sound card') at v4.7
Fixes: 86c8dd7f4d ('ALSA: firewire-digi00x: delayed registration of sound card') at v4.7
Fixes: 6c29230e2a ('ALSA: oxfw: delayed registration of sound card') at v4.7
Fixes: 7d3c1d5901 ('ALSA: fireworks: delayed registration of sound card') at v4.7
Fixes: 04a2c73c97 ('ALSA: bebob: delayed registration of sound card') at v4.7
Fixes: b59fb1900b ('ALSA: dice: postpone card registration') at v4.5
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_pcm_ops are not supposed to change at runtime. All functions
working with snd_pcm_ops provided by <sound/pcm.h> work with
const snd_pcm_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These snd_rawmidi_ops structures are only passed as the third
argument of snd_rawmidi_set_ops. This argument is const, so the
snd_rawmidi_ops structures can be const too.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At Linux v3.5, packet processing can be done in process context of ALSA
PCM application as well as software IRQ context for OHCI 1394. Below is
an example of the callgraph (some calls are omitted).
ioctl(2) with e.g. HWSYNC
(sound/core/pcm_native.c)
->snd_pcm_common_ioctl1()
->snd_pcm_hwsync()
->snd_pcm_stream_lock_irq
(sound/core/pcm_lib.c)
->snd_pcm_update_hw_ptr()
->snd_pcm_udpate_hw_ptr0()
->struct snd_pcm_ops.pointer()
(sound/firewire/*)
= Each handler on drivers in ALSA firewire stack
(sound/firewire/amdtp-stream.c)
->amdtp_stream_pcm_pointer()
(drivers/firewire/core-iso.c)
->fw_iso_context_flush_completions()
->struct fw_card_driver.flush_iso_completion()
(drivers/firewire/ohci.c)
= flush_iso_completions()
->struct fw_iso_context.callback.sc
(sound/firewire/amdtp-stream.c)
= in_stream_callback() or out_stream_callback()
->...
->snd_pcm_stream_unlock_irq
When packet queueing error occurs or detecting invalid packets in
'in_stream_callback()' or 'out_stream_callback()', 'snd_pcm_stop_xrun()'
is called on local CPU with disabled IRQ.
(sound/firewire/amdtp-stream.c)
in_stream_callback() or out_stream_callback()
->amdtp_stream_pcm_abort()
->snd_pcm_stop_xrun()
->snd_pcm_stream_lock_irqsave()
->snd_pcm_stop()
->snd_pcm_stream_unlock_irqrestore()
The process is stalled on the CPU due to attempt to acquire recursive lock.
[ 562.630853] INFO: rcu_sched detected stalls on CPUs/tasks:
[ 562.630861] 2-...: (1 GPs behind) idle=37d/140000000000000/0 softirq=38323/38323 fqs=7140
[ 562.630862] (detected by 3, t=15002 jiffies, g=21036, c=21035, q=5933)
[ 562.630866] Task dump for CPU 2:
[ 562.630867] alsa-source-OXF R running task 0 6619 1 0x00000008
[ 562.630870] Call Trace:
[ 562.630876] ? vt_console_print+0x79/0x3e0
[ 562.630880] ? msg_print_text+0x9d/0x100
[ 562.630883] ? up+0x32/0x50
[ 562.630885] ? irq_work_queue+0x8d/0xa0
[ 562.630886] ? console_unlock+0x2b6/0x4b0
[ 562.630888] ? vprintk_emit+0x312/0x4a0
[ 562.630892] ? dev_vprintk_emit+0xbf/0x230
[ 562.630895] ? do_sys_poll+0x37a/0x550
[ 562.630897] ? dev_printk_emit+0x4e/0x70
[ 562.630900] ? __dev_printk+0x3c/0x80
[ 562.630903] ? _raw_spin_lock+0x20/0x30
[ 562.630909] ? snd_pcm_stream_lock+0x31/0x50 [snd_pcm]
[ 562.630914] ? _snd_pcm_stream_lock_irqsave+0x2e/0x40 [snd_pcm]
[ 562.630918] ? snd_pcm_stop_xrun+0x16/0x70 [snd_pcm]
[ 562.630922] ? in_stream_callback+0x3e6/0x450 [snd_firewire_lib]
[ 562.630925] ? handle_ir_packet_per_buffer+0x8e/0x1a0 [firewire_ohci]
[ 562.630928] ? ohci_flush_iso_completions+0xa3/0x130 [firewire_ohci]
[ 562.630932] ? fw_iso_context_flush_completions+0x15/0x20 [firewire_core]
[ 562.630935] ? amdtp_stream_pcm_pointer+0x2d/0x40 [snd_firewire_lib]
[ 562.630938] ? pcm_capture_pointer+0x19/0x20 [snd_oxfw]
[ 562.630943] ? snd_pcm_update_hw_ptr0+0x47/0x3d0 [snd_pcm]
[ 562.630945] ? poll_select_copy_remaining+0x150/0x150
[ 562.630947] ? poll_select_copy_remaining+0x150/0x150
[ 562.630952] ? snd_pcm_update_hw_ptr+0x10/0x20 [snd_pcm]
[ 562.630956] ? snd_pcm_hwsync+0x45/0xb0 [snd_pcm]
[ 562.630960] ? snd_pcm_common_ioctl1+0x1ff/0xc90 [snd_pcm]
[ 562.630962] ? futex_wake+0x90/0x170
[ 562.630966] ? snd_pcm_capture_ioctl1+0x136/0x260 [snd_pcm]
[ 562.630970] ? snd_pcm_capture_ioctl+0x27/0x40 [snd_pcm]
[ 562.630972] ? do_vfs_ioctl+0xa3/0x610
[ 562.630974] ? vfs_read+0x11b/0x130
[ 562.630976] ? SyS_ioctl+0x79/0x90
[ 562.630978] ? entry_SYSCALL_64_fastpath+0x1e/0xad
This commit fixes the above bug. This assumes two cases:
1. Any error is detected in software IRQ context of OHCI 1394 context.
In this case, PCM substream should be aborted in packet handler. On the
other hand, it should not be done in any process context. TO distinguish
these two context, use 'in_interrupt()' macro.
2. Any error is detect in process context of ALSA PCM application.
In this case, PCM substream should not be aborted in packet handler
because PCM substream lock is acquired. The task to abort PCM substream
should be done in ALSA PCM core. For this purpose, SNDRV_PCM_POS_XRUN is
returned at 'struct snd_pcm_ops.pointer()'.
Suggested-by: Clemens Ladisch <clemens@ladisch.de>
Fixes: e9148dddc3c7("ALSA: firewire-lib: flush completed packets when reading PCM position")
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In ALSA firewire stack, 8 drivers uses IEC 61883-1/6 engine for data
transmission. They have common PCM info/constraints and duplicated codes.
This commit unifies the codes into fireiwre-lib.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA fireface driver has ALSA specific operations for MIDI/PCM data.
Structured data for the operations can be constified. Additionally,
The structured data can be function local.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In recent commit for ALSA PCM core, some arrangement is done for
'struct snd_pcm_ops.ack' callback. This is called when appl_ptr is
explicitly moved in intermediate buffer for PCM frames, except for
some cases described later.
For drivers in ALSA firewire stack, usage of this callback has a merit to
reduce latency between time of PCM frame queueing and handling actual
packets in recent isochronous cycle, because no need to wait for software
IRQ context from isochronous context of OHCI 1394.
If this works well in a case that mapped page frame is used for the
intermediate buffer, user process should execute some commands for ioctl(2)
to tell the number of handled PCM frames in the intermediate buffer just
after handling them. Therefore, at present, with a combination of below
conditions, this doesn't work as expected and user process should wait for
the software IRQ context as usual:
- when ALSA PCM core judges page frame mapping is available for status
data (struct snd_pcm_mmap_status) and control data
(struct snd_pcm_mmap_control).
- user process handles PCM frames by loop just with 'snd_pcm_mmap_begin()'
and 'snd_pcm_mmap_commit()'.
- user process uses PCM hw plugin in alsa-lib to operate I/O without
'sync_ptr_ioctl' option.
Unfortunately, major use case include these three conditions.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Declare snd_kcontrol_new structures as const as they are only passed an
argument to the function snd_ctl_new1. This argument is of type const,
so snd_kcontrol_new structures having this property can be made const.
Done using Coccinelle:
@r disable optional_qualifier@
identifier x;
position p;
@@
static struct snd_kcontrol_new x@p={...};
@ok@
identifier r.x;
position p;
@@
snd_ctl_new1(&x@p,...)
@bad@
position p != {r.p,ok.p};
identifier r.x;
@@
x@p
@depends on !bad disable optional_qualifier@
identifier r.x;
@@
+const
struct snd_kcontrol_new x;
Cross compiled these files:
sound/aoa/codecs/tas.c - powerpc
sound/mips/{hal2.c/sgio2audio.c} - mips
sound/ppc/{awacs.c/beep.c/tumbler.c} - powerpc
sound/soc/sh/siu_dai.c - sh
Could not find an architecture to compile sound/sh/aica.c.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, AM824 is described as format of data block. In this
format, one data block consists of several data channels, which is aligned
to 32 bit. One data channel has 8 bit label field and 24 bit data field.
PCM frames are transferred in Multi Bit Linear Audio (MBLA) data channel.
This channel can include 16/20/24 bit PCM sample.
As long as I know, models which support IEC 61883-1/6 doesn't allow to
switch bit length of PCM sample in MBLA data channel. They always
transmit/receive PCM frames of 24 bit length. This can be seen for the
other models which support protocols similar to IEC 61883-1/6.
On the other hand, current drivers for these protocols supports 16 bit
length PCM sample in playback substream. In this case, PCM sample is put
into the MBLA data channel with 8 bit padding in LSB side. Although 16
bit PCM sample is major because it's in CD format, this doesn't represent
device capability as is.
This commit removes support for 16 bit PCM samples in playback substream.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In development period for Linux v4.10, ktime_t became an alias of s64,
instead of union. I forgot it. We can just assign zero, instead of usage
of ktime_set(0, 0).
Fixes: 1917429578 ("ALSA: fireface: add transaction support")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Two functions were introduced for the purpose of tracing but cause warnings
when tracing is disabled:
sound/firewire/motu/amdtp-motu.c:284:13: error: 'copy_message' defined but not used [-Werror=unused-function]
static void copy_message(u64 *frames, __be32 *buffer, unsigned int data_blocks,
sound/firewire/motu/amdtp-motu.c:271:13: error: 'copy_sph' defined but not used [-Werror=unused-function]
static void copy_sph(u32 *frames, __be32 *buffer, unsigned int data_blocks,
Marking them as __maybe_unused will do the right thing here.
Fixes: 17909c1b30 ("ALSA: firewire-motu: add tracepoints for SPH in IEC 61883-1 fashion")
Fixes: c6b0b9e65f ("ALSA: firewire-motu: add tracepoints for messages for unique protocol")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA driver for TASCAM FireWire series transfers MIDI messages in system
workqueue. In current design of the driver, applications should wait for
sequence of transmission when they close ALSA rawmidi character devices.
However, when considering design of rawmidi interface, it's preferable
to wait in drain ioctl.
This commit adds support for the drain ioctl to wait for the end of
the transmission.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Units on TASCAM FireWire series handle MIDI messages with support for
running status. Drivers for the series should remember current running
status and transfer valid MIDI messages. For this purpose, current
ALSA driver for the series has some members in its top-level structure.
This is due to better abstraction of async midi port. Nowadays, the
abstraction was localized just for the driver.
This commit moves the members to structure for async midi port.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In current design of ALSA driver for TASCAM FireWire series, initialization
of members in asymc midi port structure is done at device probing. Some of
the members should be initialized every time to use rawmidi devices because
they're changed in sequence of transmission for MIDI messages.
This commit adds a new function to initialize them. Invariant parameters
during object lifetime are kept as is.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA driver for TASCAM FireWire series internally allocates 4 byte buffer
for asynchronous transaction to transfer MIDI messages. However, the buffer
can be allocated with memory object of parent structure.
This commit adds 4 byte array as a member of the structure and obsoletes
the redundant allocation. This is deallocated with memory object of parent
structure.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Units on TASCAM FireWire series receive MIDI messages by asynchronous
transactions on IEEE 1394 bus. Although the transaction is sent to a
certain register, current ALSA driver for this series has a redundant design.
This commit use the same address for the transaction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series uses asynchronous transactions with fixed length
payload for MIDI messaging. On the other hand, ALSA driver for the series
has a redundant design to handle different length of payload.
This commit removes the redundant abstraction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As a result of localization of async midi port, ALSA driver for TASCAM
FireWire series can call helper function directly instead of callback
registration.
This commit removes the redundant design.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In Linux kernel 4.4, firewire-lib got a feature called as 'async midi port'
for transmission of MIDI message via IEEE 1394 asynchronous communication,
however actual consumer of this feature is ALSA driver for TASCAM FireWire
series only. When adding this feature, I assumed that ALSA driver for
Digi00x might also be a consumer, actually it's not.
This commit moves the feature from firewire-lib to firewire-tascam module.
Two minor kernel APIs are removed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
An abstraction of asynchronous transaction for transmission of MIDI
messages was introduced in Linux v4.4. Each driver can utilize this
abstraction to transfer MIDI messages via fixed-length payload of
transaction to a certain unit address. Filling payload of the transaction
is done by callback. In this callback, each driver can return negative
error code, however current implementation assigns the return value to
unsigned variable.
This commit changes type of the variable to fix the bug.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: <stable@vger.kernel.org> # 4.4+
Fixes: 585d7cba5e ("ALSA: firewire-lib: add helper functions for asynchronous transactions to transfer MIDI messages")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
During packet streaming, maximum length of payload for isochronous packet
is invariable, therefore no need to recalculate. Current ALSA IEC 61883-1/6
engine calls a function to calculate it 8,000 or more times per second
for incoming packet processing.
This commit adds a member to have maximum length of payload into 'struct
amdtp_stream', to reduces the function calls. At first callback from
isochronous context, the length is calculated and stored for later
processing.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU units transfer/receive messages in each data block of their
isochronous packet payload. A part of content in the message is cleard for
MIDI message transmission, while the rest is unknown yet. Additional
features are required to assist users and developers to reveal the
details.
This commit adds tracepoints for the purpose. The tracepoints are designed
for MOTU's protocol version 2 and 3 (Protocol version 1 is not upstreamed
yet). In the tracepoints, events are probed to gather first two 24 bit
data chunks of each data block. The chunks are formatted into elements
of 64 bit array with padding in MSB.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unique protocol is used for MOTU FireWire series. In this protocol,
data block format is not compliant to AM824 in IEC 61883-1/6. Each of
the data block consists of 24 bit data chunks, except for a first
quadlet. The quadlet is used for source packet header (SPH) described
in IEC 61883-1.
The sequence of SPH seems to represent presentation timestamp
corresponding to included data. Developers have experienced that invalid
sequence brings disorder of units in the series.
Unfortunately, current implementation of ALSA IEC 61883-1/6 engine and
firewire-motu driver brings periodical noises to the units at sampling
transmission frequency based on 44.1 kHz. The engine generates the SPH with
even interval and this mechanism seems not to be suitable to the units.
Further work is required for this issue and infrastructure is preferable
to assist the work.
This commit adds tracepoints for the purpose. In the tracepoints, events
are probed to gather the SPHs from each data blocks.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unique protocol is used for RME Fireface series. In this protocol,
payload format for isochronous packet is not compliant to CIP in
IEC 61883-1/6. The packet includes data blocks just with data channels,
without headers and any metadata.
In previous commits, ALSA IEC 61883-1/6 engine supports this protocol.
However, tracepoints are not supported yet, unlike implementation for
IEC 61883-1/6 protocol. This commit adds support of tracepoints for
the protocol.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In ALSA firewire stack, some AV/C commands are supported, including
vendor's extensions. Drivers includes response parser of each command,
according to its requirements, while the parser is written with loose
fashion in two points; error check and length check. This doesn't cause
any issues such as kernel corruption, but should be improved.
This commit modifies evaluations of return value on each parsers.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In protocol version 3, drivers can read current sampling clock status from
register 0x'ffff'f000'0b14. 8 bits of LSB of this register represents type
of signal as source of clock.
Current driver code includes invalid bitshift to handle the parameter. This
commit fixes the bug.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 5992e30034 ("ALSA: firewire-motu: add support for MOTU 828mk3 (FireWire/Hybrid) as a model with protocol version 3")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At a commit 6c29230e2a ("ALSA: oxfw: delayed registration of sound
card"), ALSA oxfw driver fails to handle SCS.1m/1d, due to -EBUSY at a call
of snd_card_register(). The cause is that the driver manages to register
two rawmidi instances with the same device number 0. This is a regression
introduced since kernel 4.7.
This commit fixes the regression, by fixing up device property after
discovering stream formats.
Fixes: 6c29230e2a ("ALSA: oxfw: delayed registration of sound card")
Cc: <stable@vger.kernel.org> # 4.7+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For digi00x series, asynchronous transaction is not used to transfer MIDI
messages to/from control surface. One of transction handlers in my previous
work loses its practical meaning.
This commit removes the handler. I note that unit of console type
transfers 0x00001000 to registered address of host space when switching
to 'standalone' mode. Then the unit generates bus reset.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At a commit c5fcee0373 ("ALSA: firewire-digi00x: add MIDI operations for
MIDI control port"), I described that MIDI messages for control surface is
transferred by a different way from the messages for physical ports.
However, this is wrong. MIDI messages to/from all of MIDI ports are
transferred by isochronous packets.
This commit removes codes to transfer MIDI messages via asynchronous
transaction, from MIDI handling layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At a commit 9dc5d31cdc ("ALSA: firewire-digi00x: handle MIDI messages in
isochronous packets"), a functionality to handle MIDI messages on
isochronous packet was supported. But this includes some of my
misunderstanding. This commit is to fix them.
For digi00x series, first data channel of data blocks in rx/tx packet
includes MIDI messages. The data channel has 0x80 in 8 bit of its MSB,
however it's against IEC 61883-6. Unique data format is applied:
- Upper 4 bits of LSB represent port number.
- 0x0: port 1.
- 0x2: port 2.
- 0xe: console port.
- Lower 4 bits of LSB represent the number of included MIDI message bytes;
0x0/0x1/0x2.
- Two bytes of middle of this data channel have MIDI bytes.
Especially, MIDI messages from/to console surface are also transferred by
isochronous packets, as well as physical MIDI ports.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Digi00x series includes two types of unit; rack and console. As long as
reading information on config rom of Digi 002 console, 'MODEL_ID' field
has a different value from the one on Digi 002 rack.
We've already got a test report from users with Digi 003 rack. We can
assume that console type and rack type has different value in the field.
This commit adds a device entry for console type. For following commits,
this commit also adds a member to 'struct snd_digi00x' to identify console
type.
$ cd linux-firewire-utils/src
$ python2 ./crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 0404f9d0 bus_info_length 4, crc_length 4, crc 63952
404 31333934 bus_name "1394"
408 60647002 irmc 0, cmc 1, isc 1, bmc 0, cyc_clk_acc 100, max_rec 7 (256)
40c 00a07e00 company_id 00a07e |
410 00a30000 device_id 0000a30000 | EUI-64 00a07e0000a30000
root directory
-----------------------------------------------------------------
414 00058a39 directory_length 5, crc 35385
418 0c0043a0 node capabilities
41c 04000001 hardware version
420 0300a07e vendor
424 81000007 --> descriptor leaf at 440
428 d1000001 --> unit directory at 42c
unit directory at 42c
-----------------------------------------------------------------
42c 00046674 directory_length 4, crc 26228
430 120000a3 specifier id
434 13000001 version
438 17000001 model
43c 81000007 --> descriptor leaf at 458
descriptor leaf at 440
-----------------------------------------------------------------
440 00055913 leaf_length 5, crc 22803
444 000050f2 descriptor_type 00, specifier_ID 50f2
448 80000000
44c 44696769
450 64657369
454 676e0000
descriptor leaf at 458
-----------------------------------------------------------------
458 0004a6fd leaf_length 4, crc 42749
45c 00000000 textual descriptor
460 00000000 minimal ASCII
464 44696769 "Digi"
468 20303032 " 002"
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface 400 is a second model of RME Fireface series, released in 2006.
This commit adds support for this model.
This model supports 8 analog channels, 2 S/PDIF channels and 8 ADAT
channels in both of tx/rx packet. The number of ADAT channels differs
depending on each mode of sampling transmission frequency.
$ python2 linux-firewire-utils/src/crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 04107768 bus_info_length 4, crc_length 16, crc 30568 (should be 61311)
404 31333934 bus_name "1394"
408 20009002 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 9 (1024)
40c 000a3501 company_id 000a35 |
410 1bd0862a device_id 011bd0862a | EUI-64 000a35011bd0862a
root directory
-----------------------------------------------------------------
414 000485ec directory_length 4, crc 34284
418 03000a35 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 8d000006 --> eui-64 leaf at 438
424 d1000001 --> unit directory at 428
unit directory at 428
-----------------------------------------------------------------
428 000314c4 directory_length 3, crc 5316
42c 12000a35 specifier id
430 13000002 version
434 17101800 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 000261a8 leaf_length 2, crc 25000
43c 000a3501 company_id 000a35 |
440 1bd0862a device_id 011bd0862a | EUI-64 000a35011bd0862a
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds hwdep interface so as the other drivers for audio and
music units on IEEE 1394 have.
This interface is designed for mixer/control applications. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds PCM functionality to transmit/receive PCM frames on
isochronous packet streaming. This commit enables userspace applications
to start/stop packet streaming via ALSA PCM interface.
Sampling rate requested by applications is used as sampling transmission
frequency of IEC 61883-1/6packet streaming. As I described in followed
commits, units in this series manages sampling clock frequency
independently of sampling transmission frequency, and they supports
resampling between their packet streaming/data block processing layer and
sampling data processing layer. This commit take this driver to utilize
these features for usability.
When internal clock is selected as source signal of sampling clock, this
driver allows user space applications to start PCM substreams at any rate
which packet streaming engine supports as sampling transmission frequency.
In this case, this driver expects units to perform resampling PCM frames
for rx/tx packets when sampling clock frequency and sampling transmission
frequency are mismatched. This is for daily use cases.
When any external clock is selected as the source signal, this driver
gets configured sampling rate from units, then restricts available
sampling rate to the rate for PCM applications. This is for studio use
cases.
Models in this series supports 64.0/128.0 kHz of sampling rate, however
these frequencies are not supported by IEC 61883-6 as sampling transmission
frequency. Therefore, packet streaming engine of ALSA firewire stack can't
handle them. When units are configured to use any external clock as source
signal of sampling clock and one of these unsupported rate is configured
as rate of the sampling clock, this driver returns EIO to user space
applications.
Anyway, this driver doesn't voluntarily configure parameters of sampling
clock. It's better for users to work with appropriate user space
implementations to configure the parameters in advance of usage.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds management functionality for packet streaming.
As long as investigating Fireface 400, there're three modes depending
on sampling transmission frequency. The number of data channels in each
data block is different depending on the mode. The set of available
data channels for each mode might be different for each protocol and
model.
The length of registers for the number of isochronous channel is just
three bits, therefore 0-7ch are available.
When bus reset occurs on IEEE 1394 bus, the device discontinues to
transmit packets. This commit aborts PCM substreams at bus reset handler.
As I described in followed commits, The device manages its sampling clock
independently of sampling transmission frequency against IEC 61883-6.
Thus, it's a lower cost to change the sampling transmission frequency,
while data fetch between streaming layer and DSP require larger buffer
for resampling. As a result, device latency might tend to be larger than
ASICs for IEC 61883-1/6 such as DM1000/DM1100/DM1500 (BeBoB),
DiceII/TCD2210/TCD2220/TCD3070 and OXFW970/971.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating Fireface 400, format of payload of each
isochronous packet is not IEC 61883-1/6, thus its format of data block
is not AM824. The remarkable points of the format are:
* The payload just consists of some data channels of quadlet size without
CIP header.
* Each data channels includes data aligned to little endian order.
* One data channel consists of two parts; 8 bit ancillary field and 24 bit
PCM frame.
Due to lack of CIP headers, rx/tx packets include no CIP headers and
different way to check packet discontinuity. For tx packet, the ancillary
field is used for counter. However, the way of counting is different
depending on positions of data channels. At 44.1 kHz, ancillary field in:
* 1st/6th/9th/10th/14th/17th data channels: not used for this purpose.
* 2nd/18th data channels: incremented every data block (0x00-0xff).
* 3rd/4th/5th/11th/12th/13th data channels: incremented every 256 data
blocks (0x00-0x07).
* 7th/8th/15th/16th data channels: incremented per the number of data
blocks in a packet. The increment can occur per packet (0x00-0xff).
For tx packet, tag of each isochronous packet is used for this purpose.
The value of tag cyclically changes between 0, 1, 2 and 3 in this order.
The interval is different depending on sampling transmission frequency.
At 44.1/48.0 kHz, it's 256 data blocks. At 88.2 kHz, it's 96 data blocks.
The number of data blocks in tx packet is exactly the same as
SYT_INTERVAL. There's no empty packet or no-data packet, thus the
throughput is not 8,000 packets per sec. On the other hand, the one in
rx packet is 8,000 packets per sec, thus the number of data blocks is
different between each packet, depending on sampling transmission
frequency:
* 44.1 kHz: 5 or 6
* 48.0 kHz: 5 or 6 or 7
* 88.2 kHz: 10 or 11 or 12
This commit adds data processing layer to satisfy the above specification
in a policy of 'best effort'. Although PCM frames are handled for
intermediate buffer to user space, the ancillary data is not handled at all
to reduce CPU usage, thus counter is not checked. 0 is always used for tag
of isochronous packet. Furthermore, the packet streaming layer is
responsible for calculation of the number of data blocks for each packet,
thus it's not exactly the same sequence from the above observation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating Fireface 400, IEC 61883-1/6 is not applied to
its packet streaming protocol. Remarks of the specific protocol are:
* Each packet doesn't include CIP headers.
* 64,0 and 128,0 kHz are supported.
* The device doesn't necessarily transmit 8,000 packets per second.
* 0, 1, 2, 3 are used as tag for rx isochronous packets, however 0 is
used for tx isochronous packets.
On the other hand, there's a common feature. The number of data blocks
transferred in a second is the same as sampling transmission frequency.
Current ALSA IEC 61883-1/6 engine already has a method to calculate it and
this driver can utilize it for rx packets, as well as tx packets.
This commit adds support for the transferring protocol. CIP_NO_HEADERS
flag is newly added. When this flag is set:
* Both of 0 (without CIP header) and 1 (with CIP header) are used as tag
to handle incoming isochronous packet.
* 0 (without CIP header) is used as tag to transfer outgoing isochronous
packet.
* Skip CIP header evaluation.
* Use unique way to calculate the quadlets of isochronous packet payload.
In ALSA PCM interface, 128.0 kHz is not supported, and the ALSA
IEC 61883-1/6 engine doesn't support 64.0 kHz. These modes are dropped.
The sequence of rx packet has a remarkable quirk about tag. This will be
described in later commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Audio and music units of RME Fireface series use its own protocol for
isochronous packets to transfer data. This protocol requires ALSA IEC
61883-1/6 engine to have alternative functions.
This commit is a preparation for the protocol.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Drivers can retrieve the state and configuration of clock by read
transactions.
This commit allows protocol abstraction layer to to dump the
information for debugging, via proc interface.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In previous commit, fireface driver supports unique transaction mechanism
for MIDI feature. This commit adds MIDI functionality for userspace
applications.
As I wrote in a followed commit, user space applications get some
requirement from this driver. It should not touch a register to which
units transmit MIDI messages. It should configure a register in which
MIDI transmission is controlled.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating Fireface 400, MIDI messages are transferred by
asynchronous communication over IEEE 1394 bus.
Fireface 400 receives MIDI messages by write transactions to two addresses;
0x'0000'0801'8000 and 0x'0000'0801'9000. Each of two seems to correspond to
MIDI port 1 and 2.
Fireface 400 transfers MIDI messages by write transactions to certain
addresses which configured by drivers. The drivers can decide upper 4 byte
of the addresses by write transactions to 0x'0000'0801'03f4. For the rest
part of the address, drivers can select from below options:
* 0x'0000'0000
* 0x'0000'0080
* 0x'0000'0100
* 0x'0000'0180
Selected options are represented in register 0x'0000'0801'051c as bit
flags. Due to this mechanism, drivers are restricted to use addresses on
'Memory space' of IEEE 1222, even if transactions to the address have
some side effects.
This commit adds transaction support for MIDI messaging, based on my
assumption that the similar mechanism is used on the other protocols. To
receive asynchronous transactions, the driver allocates a range of address
in 'Memory space'. I apply a strategy to use 0x'0000'0000 as lower 4 byte
of the address. When getting failure from Linux FireWire subsystem, this
driver retries to allocate addresses.
Unfortunately, read transaction to address 0x'0000'0801'051c returns zero
always, however write transactions have effects to the other features such
as status of sampling clock. For this reason, this commit delegates a task
to configure this register to user space applications. The applications
should set 3rd bit in LSB in little endian order.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As of 2016, RME discontinued its Fireface series, thus it's OK for us
to focus on released firmwares to drive known units.
As long as investigating Fireface 400 with Windows driver and comparing
the result to FFADO implementation, I can see these firmwares have
different register assignments. On the other hand, according to manuals
of each models, features relevant to packet streaming seem to be common,
because GUIs for these models have the same options. It's reasonable to
assume an abstraction layer of protocols to communicate to each models.
This commit adds the abstraction layer for the protocols. This layer
includes some functions to operate common features of models in this
series.
In IEC 61883-1/6, the sequence of packet can transfer timing information
to synchronize receivers to transmitters. Units of each node on IEEE 1394
bus can generate transmitter's timing clock by handling value of SYT field
in CIP header with high-precision clock. For audio and music units on
IEEE 1394 bus, this recovered clock is designed to used for sampling clock
to capture/generate PCM frames on DSP/ADC/DAC. (Actually, in this world,
there's no units to implement this specification as is, as long as I
know).
Fireface series doesn't use this mechanism. Besides, It doesn't use
isochronous packet with CIP header. It uses internal crystal unit as its
initial sampling clock. When detecting input signals which can be
available for sampling clock (e.g. ADAT input), drivers can configure
units to use the signals as source of sampling clock. When something goes
wrong, e.g. frequency mismatching between the signal and configured value,
units fallback to the other detected signals alternatively. When detecting
no alternatives, internal crystal unit is used as source of sampling
clock. On manual of Fireface 400, this mechanism is described as
'Autosync'.
On the units, packet streaming is controlled by write transactions to
certain registers. Format of the packet, e.g. the number of data channels
in a data block, is also configured by the same manner. For this purpose,
.begin_session and .finish_session is added.
The remarkable point of this protocol is to allow drivers to configure
arbitrary sampling transmission frequency; e.g. 12.345 Hz. As long as I
know, there's no actual DAC/ADC chips which support this kind of
capability. I think a pair of packet streaming layer and data block
processing layer is isolated from sampling data processing layer in a
point of governed clock. In short, between these parts, resampling layer
exists. Actually, for Fireface 400, write transactions to
0x'0000'8010'051c has an effect to change sampling clock frequency with
base frequencies (32.0/44.1/48.0 kHz) and its multipliers (x2/x4),
regardless of sampling transmission frequency.
For this reason, the abstraction layer doesn't handle parameters for
sampling clock. Instead, each implementation of .begin_session is
expected to configure sampling transmission frequency.
For packet streaming layer, it's enough to get current selection of
source signals for the sampling clock and its frequency. In the
abstraction layer, when internal crystal is selected, drivers can sets
arbitrary sampling frequency, else they should follow configured
frequency. For this purpose, .get_clock is added.
Drivers are allows to bank up data fetching from a pair of packet
streaming/data block processing layer and sampling data processing layer.
This feature seems to suppress noises at starting/stopping packet
streaming. For this purpose, .switch_fetching_mode is added.
As I described in the above, units have remarkable mechanism to manage
sampling clock and process sampling data. For debugging purpose,
.dump_sync_status and .dump_clock_config are added. I don't have a need
to common interface to represent the status and configuration,
developers can add actual implementation of the abstraction layer as they
like.
Unlike PCM frames, MIDI messages are transferred by asynchronous
communication over IEEE 1394 bus, thus target addresses are important for
this feature. The .midi_high_addr_reg, .midi_rx_port_0_reg and
.midi_rx_port_1_reg are for this purpose. I'll describe them in following
commit.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
RME Fireface series has several models and their specifications are
different. Currently, we find no way to retrieve the specifications
from actual devices and need to implement them in this driver.
This commit adds a structure to describe model specific data. This
structure has an identical name for each unit, and maximum number of
data channels in each mode. I'll describe about the mode in following
commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just after appearing on IEEE 1394 bus, this unit generates several bus
resets. This is due to loading firmware from on-board flash memory and
initialize hardware. It's better to postpone sound card registration.
This commit schedules workqueue to process actual probe processing
2 seconds after the last bus-reset. The card instance is kept at unit
probe callback and released at card free callback. Therefore, when the
actual probe processing fails, the memory block is wasted. This is due to
simplify driver implementation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new driver for RME Fireface series. This commit just
creates/removes card instance according to IEEE 1394 bus event. More
functions will be added in following commits.
Three types of firmware have released by RME GmbH; for Fireface 400, for
Fireface 800 and for UCX/802/UFX. It's reasonable that these models use
different protocol for communication. Currently, I've investigated
Fireface 400 and nothing others.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU 828mk3 (FireWire/Hybrid) is one of third generation in MOTU FireWire
series, produced in 2008/2014. This model consists of three chips for
functionality on IEEE 1394 bus:
* TI TSB41AB2 (Physical layer for IEEE 1394 bus)
* Xilinx Spartan-3E FPGA Family (Link layer for IEEE 1394 bus, packet
processing and data block processing layer)
* TI TMS320C6722 (Digital signal processing)
This commit adds a support for this model, with its unique protocol as
version 3. This protocol has some additional features to protocol
version 2.
* Support several optical interfaces.
* Support a data chunk for return of reverb effect.
* Have a quirk of tx packets.
* Support heartbeat asynchronous transaction.
In this protocol, series of transferred packets has some quirks. Below
fields in CIP headers of the packets are out of IEC 61883-1:
- SID (source node id): always 0x0d
- DBS (data block size): always 0x04
- DBC (data block counter): always 0x00
- EOH (End of header): always 0x00
Below is an actual sample of transferred packets.
quads CIP1 CIP2
520 0x0D040400 0x22FFFFFF
8 0x0D040400 0x22FFFFFF
520 0x0D040400 0x22FFFFFF
520 0x0D040400 0x22FFFFFF
8 0x0D040400 0x22FFFFFF
Status of clock is configured by write transactions to 0x'ffff'f000'0b14,
as well as version 2, while meanings of fields are different from the
former protocols. Modes of optical interfaces are configured by write
transactions to 0x'ffff'f000'0c94.
Drivers can register its address to receive heatbeat transactions from the
unit. 0x'ffff'f000'0b0c is for the higher part and 0x'ffff'f000'0b10 is
for the lower part. Nevertheless, this feature is not useless for this
driver and this commit omits it.
Each data block consists of two parts in a point of the number of included
data chunks. In both of 'fixed' and 'differed' parts, the number of
included data blocks are a multiple of 4, thus depending on models there's
some empty data chunks. For example, 828mk3 includes one pair of empty
data chunks in its fixed part. When optical interface is configured to
S/PDIF, 828mk3 includes one pair of empty data chunks in its differed part.
To reduce consumption of CPU cycles with additional conditions/loops, this
commit just exposes these empty chunks to user space as PCM channels.
Additionally, 828mk3 has a non-negligible overhead to change its sampling
transfer frequency. When softwares send asynchronous transaction to
perform it, LED on the unit starts to blink. In a worst case, it continues
blink during several seconds; e.g. 10 seconds. When stopping blinking,
the unit seems to be prepared for the requested sampling transfer
frequency. To wait for the preparation, this commit forces the driver
to call task scheduler and applications sleeps for 4 seconds.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-1, when two quadlets CIP header is used, the most significant
bit in second CIP header stands. However, packets from units with MOTU
protocol version 3 have a quirk without this flag. Current packet streaming
layer handles this as protocol error.
This commit adds a new enumeration constant for this quirk, to handle MOTU
protocol version 3.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU 828mk2 is one of second generation in MOTU FireWire series, produced in
2003. This model consists of four chips:
* TI TSB41AB2 (Physical layer for IEEE 1394 bus)
* PDI 1394L40BE (Link layer for IEEE 1394 bus and packet processing layer)
* ALTERA ACEX 1K EP1K30 Series FPGA (Data block processing layer)
* TI TMS320VC5402 (Digital signal processing)
This commit adds a support for this model, with its unique protocol as
version 2. The features of this protocol are:
* Support data chunks for status and control messages for both
directions.
* Support a pair of MIDI input/output.
* Support a data chunk for mic/instrument independent of analog line in.
* Support a data chunk for playback return.
* Support independent data chunks for S/PDIF of both optical/coaxial
interfaces.
* Support independent data chunks for each of main out and phone out.
Status of clock is configured by write transactions to 0x'ffff'f000'0b14.
Modes of optical interfaces are configured by write transactions to
0x'ffff'f000'0c04.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU FireWire series can transfer messages to registered address. These
messages are transferred for the status of internal clock synchronization
just after starting streams.
When the synchronization is stable, it's 0x01ffffff. Else, it's 0x05ffffff.
This commit adds a functionality for user space applications to receive
content of the message.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds hwdep interface so as the other sound drivers for units
on IEEE 1394 bus have.
This interface is designed for mixer/control applications. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In MOTU FireWire series, MIDI messages are multiplexed to isochronous
packets as well as PCM frames, while the way is different from the one
in IEC 61883-6.
MIDI messages are put into a certain position in message chunks. One data
block can includes one byte of the MIDI messages. When data block includes
a MIDI byte, the block has a flag in a certain position of the message
chunk. These positions are unique depending on protocols.
Once a data block includes a MIDI byte, some following data blocks includes
no MIDI bytes. Next MIDI byte appears on a data block corresponding to
next cycle of physical MIDI bus. This seems to avoid buffer overflow caused
by bandwidth differences between IEEE 1394 bus and physical MIDI bus.
This commit adds MIDI functionality to transfer/receive MIDI messages.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds PCM functionality to transmit/receive PCM samples.
When one of PCM substreams are running or external clock source is
selected, current sampling rate is used. Else, the sampling rate is
changed according to requests from a userspace application.
Available number of samples in a frame of PCM substream is determined at
open(2) to corresponding PCM character device. Later, packet streaming
starts by ioctl(2) with SNDRV_PCM_IOCTL_PREPARE. In theory, between them,
applications can change state of the unit by any write transaction to
change the number. In this case, this driver may fail packet streaming due
to wrong data format.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a functionality to manage packet streaming for MOTU
FireWire series.
The streaming is not controlled by CMP, thus against IEC 61883-1. Write
transaction to certain addresses start/stop packet streaming.
Transactions to 0x'ffff'f000'0b00 results in isochronous channel number for
both directions and starting/stopping transmission of packets. The
isochronous channel number is represented in 6 bit field, thus units can
identify the channels up to 64, as IEEE 1394 bus specification described.
Transactions to 0x'ffff'f000'0b10 results in packet format for both
directions and transmission speed. When each of data block includes fixed
part of data chunks only, corresponding flags stand.
When bus reset occurs, the units continue to transmit packets with
non-contiguous data block counter. This causes discontinuity detection in
packet streaming engine and ALSA PCM applications receives EPIPE from any
I/O operation. In this case, typical applications manage to recover
corresponding PCM substream. This behaviour is kicked much earlier than
callback of bus reset handler by Linux FireWire subsystem, therefore
status of packet streaming is not changed in the handler.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
All models of MOTU FireWire series can be controlled by write transaction
to addresses in a range from 0x'ffff'f0000'0b00 to 0x'ffff'f000'0cff.
The models support asynchronous notification. This notification has 32 bit
field data, and is transferred when status of clock changes. Meaning of
the value is not enough clear yet.
Drivers can register its address to receive the notification. Write
transaction to 0x'ffff'f000'0b04 registers higher 16 bits of the address.
Write transaction to 0x'ffff'f0000'0b08 registers the rest of bits. The
address includes node ID, thus it should be registered every time of bus
reset.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU FireWire series uses blocking transmission for AMDTP packet streaming.
They transmit/receive 8,000 packets per second, to handle the same number
of data blocks as current sampling transmission frequency. Thus,
IEC 61883-1/6 packet streaming engine of ALSA firewire stack is available
for them.
However, the sequence of packet and data blocks includes some quirks.
Below sample is a sequence of CIP headers of packets received by 828mk2,
at 44.1kHz of sampling transmission frequency.
quads CIP1 CIP2
488 0x020F04E8 0x8222FFFF
8 0x020F04F8 0x8222FFFF
488 0x020F0400 0x8222FFFF
488 0x020F0408 0x8222FFFF
8 0x020F04E8 0x8222FFFF
488 0x020F04F0 0x8222FFFF
488 0x020F04F8 0x8222FFFF
The SID (source node ID), DBS (data block size), SPH (source packet header),
FMT (format ID), FDF (format dependent field) and SYT (time stamp) fields
are in IEC 61883-1. Especially, FMT is 0x02, FDF is 0x22 and SYT is 0xffff
to define MOTU specific protocol. In an aspect of dbc field, the value
represents accumulated number of data blocks included the packet. This
is against IEC 61883-1, because according to the specification this value
should be the number of data blocks already transferred.
In ALSA IEC 61883-1/6 engine, this quirk is already supported by
CIP_DBC_IS_END_EVENT flag, because Echo Audio Fireworks has.
Each data block includes SPH as its first quadlet field, to represent its
presentation time stamp. Actual value of SPH is compliant to IEC 61883-1;
lower 25 bits of 32 bits width consists of 13 bits cycle count and 12 bits
cycle offset.
The rest of each data block consists of 24 bit chunks. All of PCM samples,
MIDI messages, status and control messages are transferred by the chunks.
This is similar to '24-bit * 4 Audio Pack' in IEC 61883-6. The position of
each kind of data depends on generations of each model. The number of
whole chunks in a data block is a multiple of 4, to consists of
quadlet-aligned packets.
This commit adds data block processing layer specific for the MOTU
protocol. The remarkable point is the way to generate SPH header. Time
stamps for each data blocks are generated by below calculation:
* Using pre-computed table for the number of ticks per event
* 44,1kHz: (557 + 123/441)
* 48.0kHz: (512 + 0/441)
* 88.2kHz: (278 + 282/441)
* 96.0kHz: (256 + 0/441)
* 176.4kHz: (139 + 141/441)
* 192.0kHz: (128 + 0/441)
* Accumulate the ticks and set the value to SPH for every events.
* This way makes sense only for blocking transmission because this mode
transfers fixed number or none of events.
This calculation assumes that each data block has a PCM frame which is
sampled according to event timing clock. Current packet streaming layer
has the same assumption.
Although this sequence works fine for MOTU FireWire series at sampling
transmission frequency based on 48.0kHz, it is not enough at the frequency
based on 44.1kHz. The units generate choppy noise every few seconds.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit c8bdf49b9935("ALSA: fireworks/firewire-lib: Add a quirk for the
meaning of dbc") adds CIP_DBC_IS_END_EVENT flag just for tx packets.
However, MOTU FireWire series has this quirk for rx packets.
This commit allows both directions with the flag.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-1, CIP headers can have a SPH field. When a packet has 1 in
SPH field of its CIP header, the packet has a source packet headers. A
source packet header consists of 32 bit field (= 1 quadlet) and it
transfers time stamp, which is the same value as the lower 25 bits of the
IEEE 1394 CYCLE_TIMER register and the rest is zero.
This commit just supports source packet header field because IEC 61883-1
includes ambiguity the position of this header and its count. Each
protocol layer is allowed to have actual implementation according its
requirements.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, packet streaming layer passes generated SYT value to data block
processing layer. However, this is not enough in a case that the data block
processing layer generates time stamps by its own ways.
For out-packet stream, the packet streaming layer guarantees 8,000 times
calls of data block processing layers per sec. Therefore, when cycle count
of the first packet is recorded, data block processing layers can calculate
own time stamps with the recorded value.
For the reason, this commit allows packet streaming layer to record the
first cycle count. Each data block processing layer can read the count by
accessing a member of structure for packet streaming layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In an aspect of used protocols to communicate, models of MOTU FireWire
units are categorized to three generations.
This commit adds an abstraction layer of the protocols for features
related to packet streaming functionality. This layer includes 5
operations.
When configuring packet streaming functionality with sampling rate and
sampling transmission frequency, .get_clock_rate and .set_clock_rate are
called with proper arguments. MOTU FireWire series supports up to 192.0kHz.
When checking current source of sampling clock (not clock for packetization
layer), .get_clock_source is used. Enumeration is added to represent the
sources supported by this series. This operation can be used to expose
available sampling rate to user space applications when the unit is
configured to use any input signal as source of clock instead of crystal
clock.
In the protocols, the path between packet processing layer and digital
signal processing layer can be controlled. This looks a functionality to
'mute' the unit. For this feature, .switch_fetching_mode is added. This
can be used to suppress noises every time packet streaming starts/stops.
In a point of the size of data blocks at a certain sampling transmission
frequency, the most units accept several modes. This is due to usage of
optical interfaces. The size differs depending on which modes are
configured to the interfaces; None, S/PDIF and ADAT. Additionally, format
of packet is different depending on protocols. To cache current size of
data blocks and its format, .cache_packet_formats is added. This is used
by PCM functionality, packet streaming functionality and data block
processing layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU FireWire series doesn't tell drivers their capabilities, thus
the drivers should have and apply model-dependent parameters to detected
models.
This commit adds a structure to represent such parameters. Capabilities
are represented by enumeration except for the number of analog line
in/out. Identification name also be in the structure because the units has
no registers for this purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just after appearing on IEEE 1394 bus, this unit generates several bus
resets. This is due to loading firmware from on-board flash memory and
initialize hardware. It's better to postpone sound card registration.
This commit applies this idea.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds an new driver for MOTU FireWire series. In this commit,
this driver just creates/removes card instance according to bus event.
More functionalities will be added in following commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some identifiers are referred just by one functions. In this case, they
can be put into the function definition. This brings two merits; readers
can easily follow codes related to the identifiers, developers are free
from name conflict.
This commit moves such identifiers to each function definition.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now snd_rawmidi_ops is maintained as a const pointer in snd_rawmidi,
we can constify the definitions.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some identifiers are referred just by one functions. In this case, they
can be put into the function definition. This brings two merits; readers
can easily follow codes related to the identifiers, developers are free
from name conflict.
This commit moves such identifiers to each function definition.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some identifiers are referred just by one functions. In this case, they
can be put into the function definition. This brings two merits; readers
can easily follow codes related to the identifiers, developers are free
from name conflict.
This commit moves such identifiers to each function definition.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some identifiers are referred just by one functions. In this case, they
can be put into the function definition. This brings two merits; readers
can easily follow codes related to the identifiers, developers are free
from name conflict.
This commit moves such identifiers to each function definition.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some identifiers are referred just by one functions. In this case, they
can be put into the function definition. This brings two merits; readers
can easily follow codes related to the identifiers, developers are free
from name conflict.
This commit moves such identifiers to each function definition.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some identifiers are referred just by one functions. In this case, they
can be put into the function definition. This brings two merits; readers
can easily follow codes related to the identifiers, developers are free
from name conflict.
This commit moves such identifiers to each function definition.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some identifiers are referred just by one functions. In this case, they
can be put into the function definition. This brings two merits; readers
can easily follow codes related to the identifiers, developers are free
from name conflict.
This commit moves such identifiers to each function definition.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 6b7e95d133. This commit
is based on a concern about value of the given parameter. It's expected
to be ORed value with some enumeration-constants, thus often it can not be
one of the enumeration-constants. I understood that this is out of
specification and causes implementation-dependent issues.
In C language specification, enumerated type can be interpreted as an
integer type, in which all of enumeration-constants in corresponding
enumerator-list can be stored. Implementations can select one of char,
signed int and unsigned int as its type, and this selection is
implementation-dependent.
In GCC, a signed integer is selected when at least one of
enumeration-constants has negative value, else an unsigned integer is
selected. This behaviour can be switched by -fshort-enums to short type.
Anyway, the type can be decided after scanning all of
enumeration-constants.
Totally, there's no rules to constrain the value of enumerated type to
be one of enumeration-constants. In short, in enumerated type, decision
of actual type for the type is the most important and
enumeration-constants are just used for the decision, thus it's permitted
to have an integer value in a range of enumeration-constants. In our case,
actual type for the type is currently deterministic to be either char or
unsigned int. Under GCC, it's unsigned int.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As of kernel 4.10, ALSA dice driver is expected to be used in default
speed. In most cases, it's S400. While, IEEE 1394 specification describes
the other speed such as S800.
According to 'TCD30XX User Guide', its link layer controller supports
several transmission speed up to S800[0]. In Dice software interface,
transmission speed in output direction can be configured by asynchronous
transaction to 'TX_SPEED' offset in its address space. S800 may be
available.
This commit improves configuration of transmission unit before starting
packet streaming for this purpose. The value of 'max_speed' in 'fw_device'
data structure has available maximum speed decided in bus arbitration,
thus it's within capacity of the unit.
[0] TCD3xx User Guide - TCAT 1394 LLC, Revision 0.9.0-41360 (TC Applied Technologies, May 6 2015)
http://www.tctechnologies.tc/index.php/support/support-hardware/dice-iii-detailed-documentation
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The 'amdtp_stream' structure is initialized by a call of
'amdtp_stream_init()'. Although a parameter of this function is for bit
flags of packet attributes, its type is enumerator.
This commit changes the type so that it's proper for a bit flags.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This module has a bug not to return error code in a case that data
structure for transmitted packets fails to be initialized.
This commit fixes the bug.
Fixes: 35efa5c489 ("ALSA: firewire-tascam: add streaming functionality")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA fireworks driver has a bug not to call an API to destroy
'cmp_connection' structure for input direction. Currently this causes no
issues because it just destroys 'mutex' structure, while it's better to
fix it for future work.
Fix: d23c2cc448 ("ALSA: fireworks/bebob/dice/oxfw: allow stream destructor after releasing runtime")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Check for snd_pcm_ops structures that are only stored in the ops field of a
snd_soc_platform_driver structure or passed as the third argument to
snd_pcm_set_ops. The corresponding field or parameter is declared const,
so snd_pcm_ops structures that have this property can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_pcm_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_platform_driver e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i;
expression e1, e2;
position p;
@@
snd_pcm_set_ops(e1, e2, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_pcm_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_pcm_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Sakamoto