According to the HDMI specification, a source is permitted to
transmit L-PCM audio in the following sample rates: 32kHz, 44.1kHz,
48kHz, 88.2kHz, 96kHz, 176.4kHz or 192kHz.
It also supports up to 8 audio channels.
The sink may not necessarily support all these sample rates and
channels. However, as this CPU DAI describes the HDMI source, it
makes sense to include them. The limitation of capabilities as
supported by the sink should be done in the ASoC HDMI codec.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Before starting to play audio, we need to make sure that the
display is active and the current video mode supports audio. instead
of using the overlay manager in the machine driver, we use the DSS audio
interface's audio_supported function. As we already have a pointer to
the correct dssdev, we do not have to look for it every time audio is
to be played. Also, the CPU DAI startup function is called earlier
than the card hw_param function. Hence and we can detect the state of
the display earlier.
While there, add a error message if the constraint cannot be applied.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
squash to improve err
Signed-off-by: Liam Girdwood <lrg@ti.com>
Expand the configuration of the hw_params to include the IEC-60958
channel status word and the CEA-861 audio infoframe. The configuration
of such structures depends on the snd_pcm_hw_params received. A
omap_dss_audio is used to pass the configuration parameters to DSS.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Instead of accessing the HDMI IP directly, the CPU DAI driver takes
advantage of the audio interface provided by the DSS device driver.
The ASoC driver will link the DSS audio functionality with ALSA by
calling the appropriate DSS device driver functions at the relevant
moments. For this, three new DAI operations are added: trigger, prepare
and shutdown operations.
At the moment, it is assumed that only one HDMI display is available
in the system, as it is the case in OMAP4. However, in the future,
one DAI for each HDMI display should be provided.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Create a struct hdmi_priv to store the relevant data of the CPU DAI
driver. As more data is added to the driver, having all the data
in the same location eases its handling. At the moment, only the DMA
configuration parameters are included in the structure.
Also, the required memory is allocated using devm_kzalloc rather than
using a static global variable.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
When getting the needed resources fails, return -ENODEV. This is more
in line with other drivers do and it gives a more descriptive error.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In order to utilize the new OMAP HDMI codec and the updated name of
the device of the CPU DAI, update the names at the drivers accordingly.
While there, also update the name of the machine driver to be more
generic and encompass more OMAP processors featuring HDMI and not
only OMAP4.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In preparation to Device Tree support.
With DT booted kernel we can not rely on pdata which used to
hold information needed for the driver at runtime.
Use the card's driver data to hold these informations from now on.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The needed change in routing will be done runtime for the non
twl6040 connected widgets, like the Digital microphone.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
There is no need to have two snd_soc_dai_link structure for the two setup
the machine driver supports.
We can just tell core to register only the first link if the DMIC link is
not in use on the device.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Device tree support for OMAP4+ dmic cpu dai driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Device tree support for OMAP4+ McPDM cpu dai driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In capture stream the buffer size does not need to be constrained to be
bigger then the McBSP FIFO.
In capture the FIFO content is taken out in period length burst, this
enusres that the FIFO is not going to overflow.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
With the common irq the driver only needs to use one interrupt line, and
it provides better debugging possibilites compared to the legacy TX/RX
interrupt lines.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The frame dma_op_mode has never been used, and it is just creating
confusion for users/developers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Take the DMA packet mode into use when the McBSP is configured in element
dma_op_mode if the stream is not mono.
In this way we transfer one sample from/to McBSP FIFO upon DMA request.
This change only affects OMAP3+ versions, where the McBSP ports have FIFO.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
These are all new code, they've been in -next already so should be OK
for merge this time round. I'd been planning to send a pull request
today after they'd had a bit of exposure there to make sure breakage
didn't propagate into your tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=5L34
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Last minute updates
These are all new code, they've been in -next already so should be OK
for merge this time round. I'd been planning to send a pull request
today after they'd had a bit of exposure there to make sure breakage
didn't propagate into your tree.
The major thing here is the addition of some helpers to factor code out
of drivers, making a fair proportion of regulators much more just data
rather than code which is nice.
- Helpers in the core for regulators using regmap, providing generic
implementations of the enable and voltage selection operations which
just need data to describe them in the drivers.
- Split out voltage mapping and voltage setting, allowing many more
drivers to take advantage of the infrastructure for selectors.
- Loads and loads of cleanups from Axel Lin once again, including many
changes to take advantage of the above new framework features
- New drivers for Ricoh RC5T583, TI TPS62362, TI TPS62363, TI TPS65913,
TI TWL6035 and TI TWL6037.
Some of the registration changes to support the core refactoring caused
so many conflicts that eventually topic branches were abandoned for this
release.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=UR7s
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The major thing here is the addition of some helpers to factor code
out of drivers, making a fair proportion of regulators much more just
data rather than code which is nice.
- Helpers in the core for regulators using regmap, providing generic
implementations of the enable and voltage selection operations which
just need data to describe them in the drivers.
- Split out voltage mapping and voltage setting, allowing many more
drivers to take advantage of the infrastructure for selectors.
- Loads and loads of cleanups from Axel Lin once again, including many
changes to take advantage of the above new framework features
- New drivers for Ricoh RC5T583, TI TPS62362, TI TPS62363, TI
TPS65913, TI TWL6035 and TI TWL6037.
Some of the registration changes to support the core refactoring
caused so many conflicts that eventually topic branches were abandoned
for this release."
* tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (227 commits)
regulator: tps65910: use of_node of matched regulator being register
regulator: tps65910: dt: support when "regulators" node found
regulator: tps65910: add error message in case of failure
regulator: tps62360: dt: initialize of_node param for regulator register.
regulator: tps65910: use devm_* for memory allocation
regulator: tps65910: use small letter for regulator names
mfd: tpx6586x: Depend on regulator
regulator: regulator for Palmas Kconfig
regulator: regulator driver for Palmas series chips
regulator: Enable Device Tree for the db8500-prcmu regulator driver
regulator: db8500-prcmu: Separate regulator registration from probe
regulator: ab3100: Use regulator_map_voltage_iterate()
regulator: tps65217: Convert to set_voltage_sel and map_voltage
regulator: Enable the ab8500 for Device Tree
regulator: ab8500: Split up probe() into manageable pieces
regulator: max8925: Remove check_range function and max_uV from struct rc5t583_regulator_info
regulator: max8649: Remove unused check_range() function
regulator: rc5t583: Remove max_uV from struct rc5t583_regulator_info
regulator: da9052: Convert to set_voltage_sel and map_voltage
regulator: max8952: Use devm_kzalloc
...
Set some substream struct members to make the proc interface code work
again.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Felix Homann <linuxaudio@showlabor.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The handling for some PCM states is missing for snd_pcm_drain().
At least, XRUN streams should be simply dropped to SETUP, and a few
initial invalid states should be rejected.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The module_platform_driver() conversion ended up tripping over the driver
name, leading to confusion in the macro with regards to 'driver' being
redefined. rename it to something slightly more suitable to avoid
namespace collisions.
sound/sh/sh_dac_audio.c:444:122: error: conflicting types for 'driver_init'
include/linux/device.h:773:6: note: previous declaration of 'driver_init' was here
make[3]: *** [sound/sh/sh_dac_audio.o] Error 1
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SupherH FSI2 can use special data transfer,
but it depends on CPU-FSI2 connection style.
We can use 16bit data stream mode if it was valid connection,
and it is required for 16bit data DMA transfer / SPDIF sound output.
We can use 24bit data transfer if it was invalid connection.
We can select connection type if CPU is SH7372,
and it is always valid connection if latest SuperH.
This patch adds new bus_option and fsi_bus_setup()
for supporting these feature.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
fsi_hw_startup/shutdown() needs the setup of bus width,
but it is impossible to get parameter of snd_pcm_runtime at this timing.
So, these functions are changed so that be called from fsi_dai_trigger().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds fsi_version() function for accessing version.
And there were some meaningless version check which never hit.
This patch removed it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Like the previous fixes for cache hash accesses, a protection over
accesses to the widget connection list array must be provided.
Together with this action, remove snd_hda_get_conn_list() which can be
always race, and replace it with either snd_hda_get_num_conns() or
snd_hda_get_connections() calls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce codec for HDMI. At the moment, this is a dummy codec. In the
future it will parse the EDID to modify the supported parameters, such
as the number of channels and the sample rates. At the moment, it blindly
supports all the sample rates and audio channels described in the HDMI
1.4a specification.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is an spin_unlock() missing on this error path.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few last-minute regression fixes for 3.4 final kernel.
All trivial, and Cc'ed to stable kernel.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=e/ZS
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few last-minute regression fixes for 3.4 final kernel. All trivial,
and Cc'ed to stable kernel."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm8994: Fix AIF2ADC power down
ALSA: hda/idt - Fix power-map for speaker-pins with some HP laptops
ASoC: cs42l73: Sync digital mixer kcontrols to allow for 0dB
* 'clk-next' of git://git.linaro.org/people/mturquette/linux:
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
ARM: Orion: SDIO: Add support for clk.
ARM: Orion: NAND: Add support for clk, if there is one.
ARM: Orion: EHCI: Add support for enabling clocks
ARM: Orion: SATA: Add per channel clk/clkdev support.
ARM: Orion: UART: Get the clock rate via clk_get_rate().
ARM: Orion: WDT: Add clk/clkdev support
ARM: Orion: Eth: Add clk/clkdev support.
ARM: Orion: SPI: Add clk/clkdev support.
ARM: Orion: Add clocks using the generic clk infrastructure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 4924082 "ASoC: core: Flip master for CODECs in the CPU slot of a
CODEC<->CODEC link" added code that was conditional on there being no
PCM/DMA driver for the link. However, it failed to cover the case where
the link was instantiated from device tree, and hence was specified by
DT node rather than name.
This prevents the following error on Toshiba AC100:
aplay: pcm_write:1603: write error: Input/output error
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some last minute fixes for ASoC. Small, focused changes to specific
drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=iqgt
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Last minute fixes
Some last minute fixes for ASoC. Small, focused changes to specific
drivers.
* linus/master: (805 commits)
tty: Fix LED error return
openvswitch: checking wrong variable in queue_userspace_packet()
bonding: Fix LACPDU rx_dropped commit.
Linux 3.4-rc7
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
MAINTAINERS: Add myself as the cpufreq maintainer
dm mpath: check if scsi_dh module already loaded before trying to load
dm thin: correct module description
dm thin: fix unprotected use of prepared_discards list
dm thin: reinstate missing mempool_free in cell_release_singleton
gpio/exynos: Fix compiler warnings when non-exynos machines are selected
gpio: pch9: Use proper flow type handlers
powerpc/irq: Fix another case of lazy IRQ state getting out of sync
ks8851: Update link status during link change interrupt
...
Conflicts:
drivers/media/common/tuners/xc5000.c
drivers/media/common/tuners/xc5000.h
drivers/usb/gadget/uvc_queue.c
get_min_max_with_quirks() must be called after the control id name
string is determined, but the current code changes the id name string
after calling the function.
Reported-by: Christian Melki <christian.melki@ericsson.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch just sets the codec probe_mask=0x101 value for the WinFast VP200 H
PCoIP card based on Teradici hardware matching the PCI subsystem vendor/device
IDs 3a21:040d. The user reported no codec detection issues without this
explicit codec configuration.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Maintain both streams (playback, capture) synchronized. Previous code
didn't take in account the small byte count drifts caused by the irq
position rounding.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS on some HP laptops don't set the speaker-pins as fixed but expose
as jacks, and this confuses the driver as if these pins are
jack-detectable. As a result, the machine doesn't get sounds from
speakers because the driver prepares the power-map update via jack
unsol events which never come up in reality. The bug was introduced
in some time in 3.2 for enabling the power-mapping feature.
This patch fixes the problem by replacing the check of the persistent
power-map bits with a proper is_jack_detectable() call.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43240
Cc: <stable@vger.kernel.org> [v3.2+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rename the function v4l2_dont_use_lock to v4l2_disable_ioctl_locking,
and rename v4l2_dont_use_cmd to v4l2_disable_ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
aic3x_set_headset_detection() isn't made available outside the driver or
referenced within the driver which sparse notices and complains about.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the support for VGA-switcheroo in the HD-audio controller side.
When the graphics controller is disabled, the HD-audio driver also delays
the initialization until it's activated by VGA-switcheroo.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43155
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's a preliminary work for the vga-switcher support.
Export the function to do pseudo-lock for the sound card to be used
in other places.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a discrete-GPU is disabled by the VGA switcheroo, the
corresponding HD-audio controller for HDMI output is also disabled.
Such a dead controller still appears in the PCI device list, but you
can't access properly any longer (even calling pci_read_config_*()
triggers Oops!) which leads the stall of the whole communication of
the driver.
This patch adds a check of graphics controller at the probe time to
see whether it's disabled by vga-switcheroo. If disabled, skip the
whole initialization of this controller.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43155
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The tea575x-tuner framework can support the VIDIOC_S_HW_FREQ_SEEK for only
some of the tea575x-based boards. Mark this ioctl as invalid if the board
doesn't support it.
This fixes an issue with S_HW_FREQ_SEEK in combination with priority handling:
since the priority check is done first it could return -EBUSY, even though
calling the S_HW_FREQ_SEEK ioctl would return -ENOTTY. It should always return
ENOTTY in such a case.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trying to flush completed packets is pointless when the pointer
callback was called from the packet completion callback; avoid it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
By flushing all completed but not yet reported packets before reading
the PCM hardware position, the granularity of the pointer is improved
from the interrupt interval to the packet size.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The following patch might introduce this call chain:
PCM .pointer callback
+ fw_iso_context_flush_completions
+ packet callback
+ snd_pcm_period_elapsed
+ PCM .pointer callback
Recursive calls to the pointer callback are not possible due to the PCM
group locking, so avoid this by moving the period notification into
a separate tasklet.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In preparation for irq_domain support change the code to the not switch
based on the irq number. This actually makes things simpler, if slightly
repetitive.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the devm_ versions of the regmap and memory allocation functions,
saving some error handling code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since we only need to clock AIF2 when it's actively in use start up the
FLL for it using a supply widget which supplies AIF2CLK. This both makes
the sequencing more robust and ensures we minimise power consumption.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add device tree probe for mxs-sgtl5000 machine driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add device tree probe for mxs-saif driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Same as the commit 518de86 (ASoC: tegra: register 'platform' from DAIs,
get rid of pdev), it makes mxs-pcm not a platform_driver but helper to
register "platform", so that the platform_device for mxs-pcm can be
saved completely.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It turned out that the FLOAT format on CS4206 results in simple
noises, which implies that this is no right format as is.
Since CS4206 is the only codec supporting the float, let's disable it
until we find the correct format.
Reported-and-tested-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some of the Digital mixer kcontrol max values were off by 1 not allowing a max of 0dB.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Explained by Takashi in <s5hfwbtmz0q.wl%tiwai@suse.de>
> The reason is because get_min_max*() isn't called in the place you
> created these controls, and get_min_max() would be called only for
> integer volumes later even if uninitialized. A short cut for booleans.
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the PCM read/write loop, the driver calls snd_pcm_update_hw_ptr()
at each time at the beginning of the loop. Russell King reported that
this hogs CPU significantly.
The current code assumes that the pointer callback is very fast and
cheap, also not too much fine grained. It's not true in all cases.
When the pointer advances short samples while the read/write copy has
been performed, the driver updates the hw_ptr and gets avail > 0
again. Then it tries to read/write these small chunks. This repeats
until the avail really gets to zero.
For avoiding this situation, a simple workaround is to call
snd_pcm_update_hw_ptr() only once at starting the loop, assuming that
the read/write copy is performed fast enough. If the available count
becomes short, it goes to snd_pcm_wait_avail() anyway, and this
processes right.
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When pdata->reset_pin is passed with a negative value (means gpio
is invalid), then chip->reset_pin will not be assigned to a vaule,
it will use default value 0. This will cause unexpected behavior.
So, add this patch to correct.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Slightly more than expected as rc7, but all are reasonablly small fixes.
A few additions of HD-audio fixup entries, a couple of other regression
fixes including a revert, and a few other trivial oneliners.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQIcBAABAgAGBQJPq2sLAAoJEGwxgFQ9KSmk4ZMP/jC9XLQpn3Y95+/id/D+54R5
dU4aIQYNo1vheODv9hToN6Zvyd+FrouU7mikKwFnyJ1iuPfsxKrsaY+ifbfqXuQo
L0CuWDnwSDutDf5D3s8G+jg0VQHoYu+Dv7MgLqKs/DGYe3iNZKD34QtgOq0BVio0
9PP6bQCVB48TeTte3b0KD4O8rWBfSreDJj+UEewFy0V81f8P/e/ILJnkPW144FXy
1DaR70wE/1wvhW4GWvc+WGM+iH5mUWLaE49K7wdXqcTgR7XRejG4BjWAJBKEoHVc
o3AmFMTfidMzHokXdU6YgV16I8IXRmlEWFnlEGA5dxVsh0JP0t2d3mIQpcVJMm3E
Gpz5OMSjRvuOcW3wkNWYYgcm+npHtiRcXYKr+azFymsPoTSA0xlDoi7HQsVbMzG+
Jz5AwtsyZcp2BIolLvAJTXmBiHuRHNjHW2huqV+G2OI37A5YZWRIfD2vEF07MxXH
FMRCUEHOMVbRuvZtUnSGbcpdVuSMS2hjwsOdBcO03oPVrc/gp224oQvG2iNxsCHu
iH0s114j1mIYxVZX4dx+sjMyD9h3lVSghNQcz9Z7jShWdJBiQuiIneTd3y0FVbh1
l0Nq9A/oPbIYK9kbSb9z4J13WmXeS7rFYdFSPNJJ7XAKwIsZdqEMbxZM3fLHoi7b
dF95KKVJ7VwCeLjrDVZ4
=7Zz7
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Slightly more than expected as rc7, but all are reasonablly small
fixes. A few additions of HD-audio fixup entries, a couple of other
regression fixes including a revert, and a few other trivial
oneliners."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: sh: fix migor.c compilation
ALSA: HDA: Lessen CPU usage when waiting for chip to respond
Revert "ALSA: hda - Set codec to D3 forcibly even if not used"
ALSA: hda/realtek - Call alc_auto_parse_customize_define() always after fixup
ALSA: hdsp - Provide ioctl_compat
ALSA: hda/realtek - Add missing CD-input pin for MSI-7350 mobo
ALSA: hda/realtek - Add a fixup for Acer Aspire 5739G
ALSA: echoaudio: Remove incorrect part of assertion
The amp and caps hashes aren't protected properly for concurrent
accesses. Protect them via a new mutex now.
But it can't be so simple as originally thought: since the update of a
hash table entry itself might trigger the power-up sequence which
again accesses the hash table, we can't cover the whole function
simply via mutex. Thus the update part has to be split from the mutex
and revalidated.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
They pollute the global namespace and cause sparse to complain.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
It can only be used with a machine driver so the idiomatic thing for
ASoC is to select this driver from the machine driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The controller is compatible with HD-audio 1.0a with some specific
restrictions.
- The BDLE entries can't be over 4k boundary
- No position-buffer and no MSI
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Makes sparse happy and avoids polluting the global namespace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
We need to read the real register values
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
An API update which wasn't sufficiently thorough in updating the tree...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HF38
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Build fix for SH in 3.4
An API update which wasn't sufficiently thorough in updating the tree...
Ricardo Neri