Use the helper function time_is_{before,after}_jiffies() to improve
code readability.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the helper function time_is_{before,after}_jiffies() to improve
code readability.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the helper function time_is_{before,after}_jiffies() to improve
code readability.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the helper function time_is_{before,after}_jiffies() to improve
code readability.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
According to BSP library source, H264 neighbour info buffer size needs
to be 32 kiB for H6. This is similar to H265 decoding, which also needs
double buffer size in comparison to older Cedrus core generations.
Increase buffer size to cover H6 needs. Since increase is not that big
in absolute numbers, it doesn't make sense to complicate logic for older
generations.
Issue was discovered using iommu and cross checked with BSP library
source.
Fixes: 6eb9b758e3 ("media: cedrus: Add H264 decoding support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Some cx88 video cards may have transport stream status interrupts set
to 1 from cold start, causing errors like this:
cx88xx: cx88_print_irqbits: core:irq mpeg [0x100000] ts_err?*
cx8802: cx8802_mpeg_irq: mpeg:general errors: 0x00100000
According to CX2388x datasheet, the interrupt status register should be
cleared before enabling IRQs to stream video.
Fix it by clearing the Transport Stream Interrupt Status register.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Neighbour info buffer size needs to be 794 kiB in H6. This is actually
already indirectly mentioned in the comment, but smaller size is used
nevertheless.
Increase buffer size to cover H6 needs. Since increase is not that big
in absolute numbers, it doesn't make sense to complicate logic for older
generations.
Bug was discovered using iommu, which reported access error when trying
to play H265 video.
Fixes: 86caab29da ("media: cedrus: Add HEVC/H.265 decoding support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Platform_driver probe functions aren't called with locks held
and thus don't need GFP_ATOMIC. Use GFP_KERNEL instead.
Problem found with Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Pci_driver probe functions aren't called with locks held
and thus don't need GFP_ATOMIC. Use GFP_KERNEL instead.
Problem found with Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
VP9 support for GXM appears to have been missed from the original
codec submission [0] but it works well, so let's add support.
[0] 00c43088aa
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: ASUSTeK Computer Inc.
Product Name: A6JC
Version: 1.0
Serial Number: XXXXXXXXXXXXXXXXX
UUID: XXXXXXXXXXXXXXXXX
Wake-up Type: Power Switch
SKU Number: To Be Filled By O.E.M.
Family: To Be Filled By O.E.M.
Handle 0x0002, DMI type 2, 15 bytes
Base Board Information
Manufacturer: ASUSTeK Computer Inc.
Product Name: A6JC
Version: 1.0
Serial Number: XXXXXXXXXXXXXXXXX
Asset Tag: To Be Filled By O.E.M.
Features:
Board is a hosting board
Board is replaceable
Location In Chassis: To Be Filled By O.E.M.
Chassis Handle: 0x0003
Type: Motherboard
Contained Object Handles: 0
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: MEDIA ML <linux-media@vger.kernel.org>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When error occurs in parsing jpeg, the slot isn't acquired yet, it may
be the default value MXC_MAX_SLOTS.
If the driver access the slot using the incorrect slot number, it will
access array out of bounds.
The result is the driver will change num_domains, which follows
slot_data in struct mxc_jpeg_dev.
Then the driver won't detach the pm domain at rmmod, which will lead to
kernel panic when trying to insmod again.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
With gstreamer 1.19.3 all attempts to capture video in YUV formats on
our Allwinner H3-based custom board with an ov5640 sensor result in
pipeline crashes with the following messages:
Device '/dev/video0' does not support 2:0:0:0 colorimetry
Additional debug info:
Device wants 2:0:0:0 colorimetry
Fix this by setting the correct colorspace in sun6i_video_try_fmt().
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Call i2c_unregister_device(audio) on this error path.
Fixes: d3b2ccd9e3 ("[media] s2250: convert to the control framework")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Currently, if job is not completed for whatever reason, userspace
application can hang on ioctl and thus become unkillable.
In order to prevent that, implement watchdog, which will complete job
after 2 seconds with error state.
Concept is borrowed from hantro driver.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Several NV formats incorrectly described the Chroma order as
Cr, Cr when it actually is Cr, Cb.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Frank Barchard <fbarchard@google.com>
The print function dev_err() is redundant because platform_get_irq()
already prints an error.
Eliminate the follow coccicheck warning:
./drivers/media/platform/imx-jpeg/mxc-jpeg.c:2025:3-10: line 2025 is
redundant because platform_get_irq() already prints an error
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fix following includecheck warning:
./drivers/media/platform/aspeed-video.c: linux/videodev2.h is included
more than once.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Variable idx is being assigned a value that is never read, it is being
re-assigned a new value in the following for-loop. The assignment is
redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Variable id is being assigned a value that is never read. The
assignment is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The variable plane_fmt is being initialized with a value that is never
read, it is being re-assigned a new value on each iteration of a for
loop. The initialization is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The variable n is being assigned a value that is never read, it is
being reassigned a different value a few statements later. The
assignment is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The only usage of go7007_snd_device_ops is to pass its address to
snd_device_new() which takes a pointer to const struct snd_device_ops.
Make it const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The static array lcr2vbi is read-only so it make sense to make
it const.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The commit 47677e51e2a4("[media] em28xx: Only deallocate struct
em28xx after finishing all extensions") adds kref_get to many init
functions (e.g., em28xx_audio_init). However, kref_init is called too
late in em28xx_usb_probe, since em28xx_init_dev before will invoke
those init functions and call kref_get function. Then refcount bug
occurs in my local syzkaller instance.
Fix it by moving kref_init before em28xx_init_dev. This issue occurs
not only in dev but also dev->dev_next.
Fixes: 47677e51e2 ("[media] em28xx: Only deallocate struct em28xx after finishing all extensions")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.
Also, address the following sparse warnings:
drivers/media/usb/pwc/pwc-uncompress.c:44:44: warning: using sizeof on a flexible structure
Link: https://github.com/KSPP/linux/issues/174
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Let's v4l2 framework use a free /dev/videoX node for decode and encoder.
For the decoder call video_register_device() before register the media
controller device so the mapping between ins correctly done.
Since the registering sequence has changed rework exiting errors case too.
Fixes: 590577a4e5 ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Decoder Driver")
Fixes: 4e855a6efa ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Encoder Driver")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use of_device_get_match_data() to simplify the code.
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Current settings for video capture rgb-2-yuv is BT.601(studio swing),
but JFIF uses BT.601(full swing) to deocde. This mismatch will lead
to incorrect color. For example, input RGB value, (0, 0, 255), will
become (16, 16, 235) after jpg decoded.
Add an enum, aspeed_video_capture_format, to define VR008[7:6]
capture format and correct default settings for video capture to fix
the problem.
VR008[7:6] decides the data format for video capture as below:
* 00: CCIR601 studio swing compliant YUV format
* 01: CCIR601 full swing compliant YUV format
* 10: RGB format
* 11: Gray color mode
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Using stable-signal in resolution detection, and try detection again
if unstable.
VE_MODE_DETECT_EXTSRC_ADC: 1 if video source is from ADC output.
VE_MODE_DETECT_H_STABLE: 1 if horizontal signal detection is stable.
VE_MODE_DETECT_V_STABLE: 1 if vertical signal detection is stable.
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
VE_MODE_DT_HOR_TOLER: the tolerance in detecting for stable horizontal
signal.
VE_MODE_DT_VER_TOLER: the tolerance in detecting for stable vertical
signal.
VE_MODE_DT_HOR_STABLE: the minimum required count in detecting stable
HSYNC signal to set mode detection horizontal signal stable.
VE_MODE_DT_VER_STABLE: the minimum required count in detecting stable
VSYNC signal to set mode detection vertical signal stable.
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add comments to describe video-stat and 'struct aspeed_video'.
Add macro, ASPEED_VIDEO_V4L2_MIN_BUF_REQ, to describe the buffers
needed.
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: drop docbook tags, not needed]
When Gen3 support was first added to this R-Car VIN and CSI-2 driver the
routing was centred around the CHSEL register which multiplexes the
different parallel buses that sit between the CSI-2 receivers source
side and the VIN dma engines. This was a bad design as the multiplexing
do allow for only a few combinations and do not play nice with many
video streams in the system.
For example it's only possible for CSI-2 Virtual Channels 0 and 1 of any
given CSI-2 receiver to be used together with the scaler.
Later datasheets have expanded the documentation and it is now possible
to improve on this design by allowing any Virtual Channel to be routed
to any R-Car VIN instance, provided that there exists a parallel bus
between them. This increases the flexibility as all Virtual Channels can
now be used together with the scaler for example.
The redesign is not however perfect. While the new design allows for
many more routes, two constrains limit a small portion of routes that
was possible in the old design but are no more.
- It is no longer possible to route the same CSI-2 and VC to more then
one VIN at a time. This was theoretically possible before if the
specific SoC allowed for the same CSI-2 and VC to be routed to two
different VIN capture groups.
- It is no longer possible to simultaneously mix links from two CSI-2 IP
blocks to the same VIN capture group.
For example if VIN2 is capturing from CSI40 then VIN{0,1,3} must also
capture from CSI40. While VIN{4,5,6,7} is still free to capture from
any other CSI-2 IP in the system. Once all VIN{0,1,2,3} links to CSI40
are disabled that VIN capture group is free again to capture from any
other CSI-2 IP it is connected to.
At the core of the redesign is greater cooperator of the R-Car VIN and
CSI-2 drivers in configuring the routing. The VIN driver is after this
change only responsible to configure the full VIN capture groups
parallel buses to be to a particular CSI-2 IP. While the configuration
of which CSI-2 Virtual Channel is outputted on which of the R-Car CSI-2
IP output ports is handled by the CSI-2 driver.
Before this change the CSI-2 Virtual Channel to output port was static
in the CSI-2 driver and the different links only manipulated the VIN
capture groups CHSEL register. With this change both the CHSEl register
and the CSI-2 routing VCDT registers are modified for greater
flexibility.
This change touches both the R-Car VIN and R-Car CSI-2 drivers in the
same commit as both drivers cooperate closely and one change without the
other would more or less break video capture.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: fix two trivial checkpatch whitespace issues]
In preparation of creating more links to allow for full Virtual Channel
routing within the CSI-2 block break out the link creation logic to a
helper function as the logic will grow in future work.
There is no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The code has grown organically and a lot of checks are performed for
the CSI-2 use-case even if the link notify is for a subdevice connected
to the parallel interface.
Before reworking the CSI-2 routing logic split the CSI-2 and parallel
link notify code in two separate blocks to make it clearer. There is no
functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Replace the driver-specific definitions of MIPI CSI-2 data types with
macros from mipi-csi2.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There are many CSI-2-related drivers in the media subsystem that come
with their own macros to handle the CSI-2 data types (or just hardcode
the numerical values). Provide a shared header with definitions for
those data types that driver can use.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
VSP hardware could be used (e.g. by the bootloader) before driver load,
and some interrupts could be left in enabled and pending state. In this
case, setting up VSP interrupt handler without masking interrupts before
causes interrupt handler to be immediately called (and crash due to null
vsp->info dereference).
Fix that by explicitly masking all interrupts before setting the interrupt
handler. To do so, have to set the interrupt handler later, after hw
revision is already detected and number of interrupts to mask gets
known.
Based on patch by Koji Matsuoka <koji.matsuoka.xm@renesas.com> included
in the Renesas BSP kernel.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Adds the requisite device id to support detection of the Apple FaceTime
HD webcam exposed over the T2 BCE VHCI interface.
Tested-by: Aun-Ali Zaidi <admin@kodeit.net>
Signed-off-by: Paul Pawlowski <paul@mrarm.io>
Signed-off-by: Aun-Ali Zaidi <admin@kodeit.net>
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Without this the default (SMPTE 170M) from init_cfg stays unchanged.
Even after configuring 'srgb' colorspace (or 'raw')
$ media-ctl -V "'csis-32e30000.mipi-csi':0 [colorspace:srgb]"
the colorspace does not change at all:
$ media-ctl --get-v4l2 "'csis-32e30000.mipi-csi':0"
[fmt:SRGGB10_1X10/1920x1080 field:none colorspace:smpte170m xfer:709
ycbcr:601 quantization:lim-range]
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In cal_ctx_v4l2_init_formats(), devm_kzalloc() is assigned to
ctx->active_fmt and there is a dereference of it after that, which could
lead to NULL pointer dereference on failure of devm_kzalloc().
Fix this bug by adding a NULL check of ctx->active_fmt.
This bug was found by a static analyzer.
Builds with 'make allyesconfig' show no new warnings, and our static
analyzer no longer warns about this code.
Fixes: 7168155002 ("media: ti-vpe: cal: Move format handling to cal.c and expose helpers")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This error path needs to drop the mutex to avoid a deadlock.
Fixes: 7be91e02ed ("media: i2c: Add ov08d10 camera sensor driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
MWB gain register are used to set gain for each mwb channel mannually.
However, it will involve some artifacts at low light environment as gain
cannot be applied to each channel synchronously. Update the driver to use
group write for digital gain to make the sure RGB digital gain be applied
together at frame boundary.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
link-frequencies is required but only mentioned in the example. Add
it to the description.
Fixes: f3ce7200ca ("media: dt-bindings: media: document SK Hynix Hi-846 MIPI CSI-2 8M pixel sensor")
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields. Wrap the target region
in struct_group(). This additionally fixes a theoretical misalignment
of the copy (since the size of "buf" changes between 64-bit and 32-bit,
but this is likely never built for 64-bit).
FWIW, I think this code is totally broken on 64-bit (which appears to
not be a "real" build configuration): it would either always fail (with
an uninitialized data->buf_size) or would cause corruption in userspace
due to the copy_to_user() in the call path against an uninitialized
data->buf value:
omap3isp_stat_request_statistics_time32(...)
struct omap3isp_stat_data data64;
...
omap3isp_stat_request_statistics(stat, &data64);
int omap3isp_stat_request_statistics(struct ispstat *stat,
struct omap3isp_stat_data *data)
...
buf = isp_stat_buf_get(stat, data);
static struct ispstat_buffer *isp_stat_buf_get(struct ispstat *stat,
struct omap3isp_stat_data *data)
...
if (buf->buf_size > data->buf_size) {
...
return ERR_PTR(-EINVAL);
}
...
rval = copy_to_user(data->buf,
buf->virt_addr,
buf->buf_size);
Regardless, additionally initialize data64 to be zero-filled to avoid
undefined behavior.
Link: https://lore.kernel.org/lkml/20211215220505.GB21862@embeddedor
Cc: Arnd Bergmann <arnd@arndb.de>
Fixes: 378e3f81cb ("media: omap3isp: support 64-bit version of omap3isp_stat_data")
Cc: stable@vger.kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
MIPI CSI-2 continuous and non-continuous clock modes are mutually
exclusive. Drop the V4L2_MBUS_CSI2_CONTINUOUS_CLOCK flag and use
V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Wang Qing