When a frame is sent to a sleeping station, the
microcode reports TX_STATUS_FAIL_DEST_PS as its
status -- we need to translate that to the flag
that mac80211 expects.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In both 6x00 and 6x50 series, the enhanced/extended tx power table in
EEPROM is used to set the max. tx power limit.
This new tx power table is in 1/2 dBm format, which creates an issue of
possibility of 1/2 dBm loss when driver set the tx power limit; because
of driver keep track and report the tx power in dBm format.
In order to prevent the 1/2 dBm loss, keep track of the true max tx
power in 1/2 dBm format in driver; do the comparison and adjust the tx
power if needed when send tx power command to uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Different channel has different configuration, need to pass correct
configuration to uCode when send "channel switch" command to uCode.
Invalid configuration will cause sysassert in uCode and produce
un-expected result.
Even it is a very small windows, but we also need to consider and handle
the case if commit_rxon occurred before the "channel switch
announcement" notification received from uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fourth queue (command queue) is already activated in
the loop above that also maps it to the command FIFO and
therefore doesn't need to be marked as activated again.
Also change the TODO comment to be accurate -- we need
to initialise the _queues_, not FIFOs, and map them to
device FIFOs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6x50 series, it is wimax/wifi combo device, so driver need to enable
the wimax/wifi co-exist function and send the coexist event priority
table to uCode for operation.
The priority table will be used by uCode to determine what is the proper
action it should take when co-exist with WiMAX.
For example, when WiFi runs a scan, it must own radio exclusively, therefore
will disconnect WiMAX if WiMAX is connected.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support "channel switch" request by issue "channel switch" host command
to uCode.
There is no separated "channel switch" indication from mac80211,
when detected "IEEE80211_CONF_CHANGE_CHANNEL" flag in iwl_mac_config(),
if the station is in "associated" state, then assume "channel switch
announcement" IE was received by mac80211.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consolidate most iwlXXXX_apm_init() functions into single iwl_apm_init().
Keep iwl3945_apm_init(), but leverage iwl_apm_init() for most functionality.
Update 4965 init sequence to follow most recent factory recommendations.
Add following members to struct iwl_cfg to guide the init sequence:
pll_cfg_val (replaces needs_pll_cfg), set_l0s, use_bsm
Move L0S enable/disable from nic_config() functions to iwl_apm_init().
This satisifies the "FIXME: put here L1A -L0S w/a" notice, and complies
with factory-recommended sequence.
Add debug info message in iwl_apm_init(), and symmetrical message
in iwl_apm_stop().
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In Rx gain balancing (chain noise) computation for 5000 series and up,
the delta gain calculation should use the average noise of default
chain, not "chain 0" which do not exist for all the devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This switches the iwlwifi driver to use paged skb from linear skb for Rx
buffer. So that it relieves some Rx buffer allocation pressure for the
memory subsystem. Currently iwlwifi (4K for 3945) requests 8K bytes for
Rx buffer. Due to the trailing skb_shared_info in the skb->data,
alloc_skb() will do the next order allocation, which is 16K bytes. This
is suboptimal and more likely to fail when the system is under memory
usage pressure. Switching to paged Rx skb lets us allocate the RXB
directly by alloc_pages(), so that only order 1 allocation is required.
It also adjusts the area spin_lock (with IRQ disabled) protected in the
tasklet because tasklet guarentees to run only on one CPU and the new
unprotected code can be preempted by the IRQ handler. This saves us from
spawning another workqueue to make skb_linearize/__pskb_pull_tail happy
(which cannot be called in hard irq context).
Finally, mac80211 doesn't support paged Rx yet. So we linearize the skb
for all the management frames and software decryption or defragmentation
required data frames before handed to mac80211. For all the other frames,
we __pskb_pull_tail 64 bytes in the linear area of the skb for mac80211
to handle them properly.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of always allocate the max number of tx queue structure,
use dynamic allocation based on the number of queues in device
configuration. With these changes, device does not have to allocate more
memory than the h/w can support.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add more items to sensitivity range table to avoid using hardcoded values.
Initialize the table per device since unique per device information is
required to perform sensitivity calibration.
additional items in sensitivity range table:
.barker_corr_th_min: Barker correlation threshold minimum
.barker_corr_th_min_mrc: Barker correlation threshold minimum for MRC
.nrg_th_cca: Energy threshold for Clear Channel Assessment
Barker codes are a technique used in WLAN encoding for transmission.
MRC is "Maximal Ratio Combining", a technique for optimally combining the
signals from 2 or more receivers to achieve a better signal.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up device-specific apm_reset() functions and library infrastructure,
now that these reset() functions are no longer being used.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace iwl_poll_direct_bit with iwl_poll_bit when accessing CSR registers.
There is no need to power up the mac to access CSR registers.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Ben M Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unify the usage of apm_stop_master and apm_stop
across all hardwares.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The iwlwifi drivers have LED blinking requirements that
mac80211 cannot fulfill due to the use of just a single
LED instead of different ones for TX, RX, radio etc.
Instead, the single LED blinks according to transfers
and is solid on the rest of the time. As such, having
LED class devices registered that mac80211 triggers are
connected to is pointless as we don't use the triggers
anyway.
Remove all the useless code and add hooks into the
driver itself. At the same time, make the LED code
abstracted so the core code that determines blink rate
etc. can be shared between 3945 and agn in iwlcore.
At the same time, the fact that we removed the use of
the mac80211 LED triggers means we can also remove the
IWLWIFI_LEDS Kconfig symbol since the LED support is
now self-contained.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver should clear the translate table area after receiving "Alive"
response from uCode. This patch corrects a mistake when doing this.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Guo Chaohong <chaohong.guo@linux.intel.com>
Acked-by: Ben M Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding support of Chain Noise Calibration for 6000 series NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order for uCode to select the valid antennas for transmit, driver
need to configure the allowed tx antennas through host command.
The TX_ANT_CONFIGURATION_CMD should be used for 5000 series and up
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcode module parameter's permissions, use pre-defined.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust led blink rate to compensate on a MAC Clock difference on every
HW. Led blink rate analysis showed an average deviation of 0% on 3945,
5% on 4965 HW and 20% on 5000 series and up.
Need to compensate on the led on/off time per HW according to the
deviation to achieve the desired led frequency
The calculation is: (100-averageDeviation)/100 * blinkTime
For code efficiency the calculation will be:
compensation = (100 - averageDeviation) * 64 / 100
NewBlinkTime = (compensation * BlinkTime) / 64
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Separate set_hw_params() function for 6000
series from 5000/1000 series because:
1) 6000 series use different set of sensitivity range table
2) 6000 series has different uCode image size
Also include the new sensitivity parameters needed by sensitivity
algorithm.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Different NIC has different requirements for configuration. Currently all
5000 series hardware and later share the same configuration function even
though they do not need the same configurations. Fix this by separating the
needed configuration actions for each hardware model.
.5000 series: L1-ASPM H/W bug work-around
configure radio
write CSR_HW_IF_CONFIG_REG for uCode use
work-around for NIC get stuck after early PCIe power off
.1000 series: write CSR_HW_IF_CONFIG_REG for uCode use
setting digital SVR for 1000 card to 1.32V
.6000 series: configure radio
write CSR_HW_IF_CONFIG_REG for uCode use
write CSR_GP_DRIVER_REG to indicate radio sku
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return type of abs() was recently changed from int to long. With
min()'s type checking we thus need to make sure that values of the same
type are compared.
This fixes:
CC [M] drivers/net/wireless/iwlwifi/iwl-5000.o
drivers/net/wireless/iwlwifi/iwl-5000.c: In function ‘iwl5000_gain_computation’:
drivers/net/wireless/iwlwifi/iwl-5000.c:320: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hardware or uCode problem occurs driver captures significant
information from device to enable debugging. The format of this information
is different between 3945 and 4965 and later devices, yet currently the
3945 uses the 4965 and later format. Fix this by adding a new library call
that is initialized to the correct formatting routine based on device.
This moves the iwlagn event and error log handling back to iwl-agn.c to
make it part of iwlagn module.
Also remove the 3945 sysfs file that triggers dump of event log - there is
already a debugfs file that can do it for all drivers.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some cases firmware can give us bad value of index in transmit
buffers array. This patch add sanity check for such values and return
from processing function instantly when it happens.
https://bugzilla.redhat.com/show_bug.cgi?id=521931
Patch was tested by reporter on iwl5000. I think check can be also
helpful for 4965.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The field called 'len' in struct iwl_rx_packet is in fact not just a length
field but also includes some flags from the flow handler. In several places
throughout the driver, this causes incorrect values to be interpreted as
lengths when the field is improperly masked.
In most situations the improper use is for debugging output, and simply results
in an erroneous message, such as:
[551933.070224] ieee80211 phy0: I iwl_rx_statistics Statistics notification received (480 vs -1367342620).
which should read '(480 vs 484)'.
In at least one case this could case bad things to happen:
void iwl_rx_pm_debug_statistics_notif(struct iwl_priv *priv,
struct iwl_rx_mem_buffer *rxb)
{
struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
IWL_DEBUG_RADIO(priv, "Dumping %d bytes of unhandled "
"notification for %s:\n",
le32_to_cpu(pkt->len), get_cmd_string(pkt->hdr.cmd));
iwl_print_hex_dump(priv, IWL_DL_RADIO, pkt->u.raw, le32_to_cpu(pkt->len)
);
}
EXPORT_SYMBOL(iwl_rx_pm_debug_statistics_notif);
Given the rampant misuse of this field without proper masking throughout the
driver (every use but one), this patch renames the field from 'len' to
'len_n_flags' to reduce confusion. It also adds the proper masking when
this field is used as a length value.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding legacy thermal throttling management support to 5150 NIC
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Green-field mode should be configured in the HT station table. This patch uses
both the per-station GF support flag as well as the current BSS HT operation
mode (non-GF stations present flag).
Added the "ht_greenfield_support" field to struct iwl_cfg to replace the
device-specific check in rs_use_green(). That check has been moved to
iwlcore_init_ht_hw_capab().
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename "fat" to "ht40"
The term "fat channel" is deprecated in favor of "HT40"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6x00 2x2 NIC, two types of Power Amplifier are available.
In order for uCode to apply correct tx power,
driver needs to program the CSR_GP_DRIVER_REG register and
let uCode know the type of PA.
If driver do not program CSR_GP_DRIVER_REG register (default to 0),
then it is uCode's decision for tx power
2x2 Hybrid card: use both internal and external PA
2x2 IPA(Internal Power Amplifier) card: internal PA only
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part 1 of Thermal Throttling Management -
Thermal Throttling feature is used to put NIC into low power state when
driver detect the Radio temperature reach pre-defined threshold
Two Thermal Throttling Management Methods; this patch introduce the
Legacy Thermal Management:
IWL_TI_0: normal temperature, system power state
IWL_TI_1: high temperature detect, low power state
IWL_TI_2: higher temperature detected, lower power state
IWL_TI_CT_KILL: critical temperature detected, lowest power state
Once get into CT_KILL state, uCode go into sleep, driver will stop all
the active queues, then move to IWL_TI_CT_KILL state; also set up 5
seconds timer to toggle CSR flag, uCode wake up upon CSR flag change,
then measure the temperature.
If temperature is above CT_KILL exit threshold, uCode go backto sleep;
if temperature is below CT_KILL exit threshold, uCode send Card State
Notification response with appropriate CT_KILL status flag, and uCode
remain awake, Driver receive Card State Notification Response and update
the card temperature to the CT_KILL exit threshold.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If advance thermal throttling is used the driver need to pass both
"enter" and "exit" temperature to uCode.
Using different critical temperature threshold for legacy and advance
thermal throttling management based on the type of thermal throttling
method is used except 1000.
For 1000, it use advance thermal throttling critical temperature
threshold, but with legacy thermal management implementation until ucode
has the necessary implementations in place.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Deprecate the "debug50" module parameter used to obtain
5000 series and up debugging. Replace it with "debug" module
parameter to match with original driver and be consistent
between them. The "debug50" module parameter can still be used,
except that the module parameter is not writable in keeping
with its previous state. We currently just mark it as "deprecated"
and do not have it in the feature-removal-schedule. Some more
cleanup of module parameters needs to be done and can then be
entered together.
* Only make "debug" module parameters visible if the driver
is compiled with CONFIG_IWLWIFI_DEBUG. This will eliminate
a lot of confusion where users think they have set debug flags
but yet cannot see any debug output.
* Make module parameters writable. This eliminates the need for the
"debug_level" sysfs file, which can now also be deprecated and
added to feature-removal-schedule. This file is in significant
use though with many iwlwifi documents and text referring users
to it. We can thus not take its removal lightly and keep it around.
With iwlcore shared between iwlagn and iwl3945 we really do not need
debug module parameters for each but can instead have one debug
module parameter for the iwlcore module. The same issue is here as
with the sysfs file - a lot of iwlwifi documentation and text (like
bug reports) rely on iwlagn and iwl3945 having this module parameter,
so changing this to a module parameter of iwlcore will have significant
impact and we do not do this for that reason.
One consequence of this patch is that if a user is running a system
with both 3945 and later hardware then the setting of the one module
parameter will affect the value of the other. The likelihood of this
seems low - and even if this setup is present it does not seem like an
issue for both modules to run with the same debug level.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding new API version to account for change to ucode file format. New
header includes the build number of the ucode. This build number is the
SVN revision thus allowing for exact correlation to the code that
generated it.
The header adds the build number so that older ucode images can also be
enhanced to include the build in the future.
some cleanup in iwl_read_ucode needed to ensure old header not used and
reduce unnecessary references through pointer with the data is already
in heap variable.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On 1000, there are two Switching Voltage Regulators (SVR). The first one
apply digital voltage level (1.32V) for PCIe block and core. We need to
use this regulator to solve a stability issue related to noisy DC2DC
line in the silicon.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
max_nrg_cck value inside the sensitivity range structure is not needed
for sensitivity calibration.
Keep the parameter in sensitivity structure but set the value to "0" in case
needed in the future implementation.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In 5150 there is a long delay between the AGC(Automatic Gain Control) command
till the RF is stabilized causing us to miss detections when there was
adjacent channel noise, so we need to adjusted the Sensitivity calibration
for 5150 differently.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unifies 3945 and AGN station management
It also removes useless struct iwl_station_mgmt ops
and cleanups a bit the interface
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ICT interrupt handler support, ICT should improve CPU utilization
since it does not require target read which is very expensive. This
interrupt handler only added to 5000 cards and newer. Device will write
interrupts to ICT shared table to inform driver about its interrupts.
These patches will not touch 3945 and 4965 interrupt handlers and tasklet.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new lock to be used when accessing some registers. Also move
the register lock and iwl_grab_nic_access inside the function for register access. This
will prevent from forgetting to hold locks and nic access in the right way and make code
easier to maintain.
We over use the priv->lock spin lock and I guess we need to add new
one for Tx queue after that we might need to change most of these lock to
BH and just keep priv->lock as irq type.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The temperature measurement by uCode for 5150 and 5000 are different
CSR_HW_REV_TYPE_5150: temperature sensor output voltage
CSR_HW_REV_TYPE_5000: temperature in Celsius
temperature related operation for 5150 is measured by temperature sensor
output voltage; additional conversion is required for set and store
the temperature.
To make sure support different HW design; implement _ops method for
temperature related functions (temperature reading and set ct kill
threshold)
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
enable iwl driver to support 5000 ucode having version 2 of API
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch removes the "manual radio disable" parameter
as there is no usage scenario of disabling radio using this module parameter.
User can use iwconfig's txpower to enable and disable radio.
This module parameter also does not work as expected. During module load
the status of radio is set, the radio is not actually disabled. Even so,
the moment mac80211 requests the interface to be up the radio will be
enabled again.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add config_ap lib op to iwlwifi and iwl3945 in preparation
of future 3945 porting actions.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add set_rxon_chain op to iwlwifi cfg ops in preparation of
future 3945 porting work.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch unifies the add_station function for 3945 and iwlwifi drivers.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds declarations for station management ops to iwlwifi drivers.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg