scc_pata has the different BAR configuration and using ide_setup_pci_device()
is inappropriate.
(ide_setup_pci_device() expects a normal PCI IDE controller with
BAR0..BAR3 either non-existant or being primary/secondary port bases
in I/O space.)
This patch do all needed setup itself instead of calling ide_setup_pci_device().
[bart: minor checkpatch.pl fixes]
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
hdparm explicitely marks HDIO_[UNREGISTER,SCAN]_HWIF ioctls as DANGEROUS
and given the number of bugs we can assume that there are no real users:
* DMA has no chance of working because DMA resources are released by
ide_unregister() and they are never allocated again.
* Since ide_init_hwif_ports() is used for ->io_ports[] setup the ioctls
don't work for almost all hosts with "non-standard" (== non ISA-like)
layout of IDE taskfile registers (there is a lot of such host drivers).
* ide_port_init_devices() is not called when probing IDE devices so:
- drive->autotune is never set and IDE host/devices are not programmed
for the correct PIO/DMA transfer modes (=> possible data corruption)
- host specific I/O 32-bit and IRQ unmasking settings are not applied
(=> possible data corruption)
- host specific ->port_init_devs method is not called (=> no luck with
ht6560b, qd65xx and opti621 host drivers)
* ->rw_disk method is not preserved (=> no HPT3xxN chipsets support).
* ->serialized flag is not preserved (=> possible data corruption when
using icside, aec62xx (ATP850UF chipset), cmd640, cs5530, hpt366
(HPT3xxN chipsets), rz1000, sc1200, dtc2278 and ht6560b host drivers).
* ->ack_intr method is not preserved (=> needed by ide-cris, buddha,
gayle and macide host drivers).
* ->sata_scr[] and sata_misc[] is cleared by ide_unregister() and it
isn't initialized again (SiI3112 support needs them).
* To issue an ioctl() there need to be at least one IDE device present
in the system.
* ->cable_detect method is not preserved + it is not called when probing
IDE devices so cable detection is broken (however since DMA support is
also broken it doesn't really matter ;-).
* Some objects which may have already been freed in ide_unregister()
are restored by ide_hwif_restore() (i.e. ->hwgroup).
* ide_register_hw() may unregister unrelated IDE ports if free ide_hwifs[]
slot cannot be found.
* When IDE host drivers are modular unregistered port may be re-used by
different host driver that owned it first causing subtle bugs.
Since we now have a proper warm-plug support remove these ioctls,
then remove no longer needed:
- ide_register_hw() and ide_hwif_restore() functions
- 'init_default' and 'restore' arguments of ide_unregister()
- zeroeing of hwif->{dma,extra}_* fields in ide_unregister()
As an added bonus IDE core code size shrinks by ~3kB (x86-32).
v2:
* fix ide_unregister() arguments in cleanup_module() (Andrew Morton).
v3:
* fix ide_unregister() arguments in palm_bk3710.c.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove CONFIG_BLK_DEV_HD hack from init_hwif_default()
("hda=noprobe hdb=noprobe" kernel parameters should be used
instead if somebody wishes to use the old "hd" driver).
* Make CONFIG_BLK_DEV_HD_ONLY config option available also when
IDE subsystem is used and update help entry.
* Remove no longer needed CONFIG_BLK_DEV_HD_IDE config option.
v2:
* Update documentation to suggest "hda=noprobe hdb=noprobe"
instead of obsoleted "ide0=noprobe".
* Update Documentation/ide/ide.txt.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
request_irq() will fail if there is already another IRQ handler
registered and IRQ flags are mismatched.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_generic_sysfs_init() helper registering 'ide_generic' class
(together with ide_generic_class_release() ->class_release method)
and use it in ide_generic_init().
* Add "add" class attribute to 'ide_generic' class for adding new interfaces
(it is intended to be a replacement for obsoleted "idex=base[,ctl[,irq]]"
kernel parameters).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'struct class ide_port_class' ('ide_port' class) and a 'struct
device *portdev' ('ide_port' class device) in ide_hwif_t.
* Register 'ide_port' class in ide_init() and unregister it in
cleanup_module().
* Create ->portdev in ide_register_port () and unregister it in
ide_unregister().
* Add "delete_devices" class device attribute for unregistering IDE devices
on a port and "scan" one for probing+registering IDE devices on a port.
* Add ide_sysfs_register_port() helper for registering "delete_devices"
and "scan" attributes with ->portdev. Call it in ide_device_add_all().
* Document IDE warm-plug support in Documentation/ide/warm-plug-howto.txt.
v2:
* Convert patch from using 'struct class_device' to use 'struct device'.
(thanks to Kay Sievers for doing it)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
->busproc method is used by HDIO_SET_BUSSTATE ioctl but it has no chance
of working as intended (in 2.4.x days) because to issue an ioctl there
is a device node needed and:
- for BUSSTATE_TRISTATE+OFF it is too late (devices are already gone)
- for BUSSTATE_TRISTATE+ON it is too early (devices are not registered yet)
Just remove ->busproc method for now (it was only implemented by hpt366,
siimage and tc86c001 host drivers).
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Rework PowerMac media-bay support in such way that instead of
un/registering the IDE interface we un/register IDE devices:
* Add ide_port_scan() helper for probing+registerering devices on a port.
* Rename ide_port_unregister_devices() to __ide_port_unregister_devices().
* Add ide_port_unregister_devices() helper for unregistering devices on a port.
* Add 'ide_hwif_t *cd_port' to 'struct media_bay_info', pass 'hwif' instead
of hwif->index to media_bay_set_ide_infos() and use it to setup 'cd_port'.
* Use ide_port_unregister_devices() instead of ide_unregister()
and ide_port_scan() instead of ide_register_hw() in media_bay_step().
* Unexport ide_register_hw() and make it static.
v2:
* Fix build by adding <linux/ide.h> include to <asm-powerpc/mediabay.h>.
(Reported by Michael/Kamalesh/Andrew).
Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_cfg_mtx lock/unlock to ide_port_setup_devices() and then move
ide_port_setup_devices() call from init_irq() to ide_device_add_all().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out devices init from ide_init_port_data() to
ide_port_init_devices_data().
While at it:
* Add explicit clearing of IDE device structure.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out code unregistering devices from ide_unregister() to
ide_port_unregister_devices().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
IDE devices need to be removed from /proc/ide/ _before_ being unregistered:
* Drop 'ide_hwif_t *hwif' argument from destroy_proc_ide_device()
and use drive->hwif instead.
* Rename destroy_proc_ide_device() to ide_proc_unregister_device().
* Call ide_proc_unregister_device() in drive_release_dev().
* Remove no longer needed destroy_proc_ide_drives().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out cable detection from ide_init_port() to ide_port_cable_detect().
* Move ide_port_cable_detect() call to ide_device_add_all().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ide_find_port() instead of ide_deprecated_find_port() in bast-ide/
palm_bk3710/ide-cs/delkin_cb host drivers and in ide_register_hw().
* Remove no longer needed ide_deprecated_find_port().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Instead of checking for '->io_ports[IDE_DATA_OFFSET] == 0' check for
'->chipset == ide_unknown' when looking for an empty ide_hwifs[] slot.
* Do ide-pnp initialization after ide-generic when IDE is built-in
(ide-pnp is the only user of ide_find_port() which needs such fixup).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This hwif->chipset fixup is already present in ide_device_add_all()
but for warm-plug support we also need to reserve not currently present
interfaces.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This option is obsolete and can be removed safely.
It allows us to remove the pci_get_device_reverse() function from the
PCI core.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
According to RFC4960 7.2.2,
When all of the data transmitted by the sender has
been acknowledged by the recerver, partial_bytes_acked is initialized to 0.
This patch conforms to rfc requirement.
Without this fix, cwnd might be error incremented.
Signed-off-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'ack' is currently a simple integer that flags whether or not a client is done
touching fields in the given descriptor. It is effectively just a single bit
of information. Converting this to a flags parameter allows the other bits to
be put to use to control completion actions, like dma-unmap, and capture
results, like xor-zero-sum == 0.
Changes are one of:
1/ convert all open-coded ->ack manipulations to use async_tx_ack
and async_tx_test_ack.
2/ set the ack bit at prep time where possible
3/ make drivers store the flags at prep time
4/ add flags to the device_prep_dma_interrupt prototype
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
DMA drivers no longer need to be notified of dependency submission
events as async_tx_run_dependencies and async_tx_channel_switch will
handle the scheduling and execution of dependent operations.
[sfr@canb.auug.org.au: extend this for fsldma]
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Shrink struct dma_async_tx_descriptor and introduce
async_tx_channel_switch to properly inject a channel switch interrupt in
the descriptor stream. This simplifies the locking model as drivers no
longer need to handle dma_async_tx_descriptor.lock.
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Split MPC83xx EOCDI event from MPC85xx EOLNI event, which is
also need to update cookie and start the next transfer.
The DMA channel irq handler function code is refined.
The patch is tested on MPC8377MDS board.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by; Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Always enabling the fsl_dma_self_test() to ensure the DMA controller
should works well after the driver probed.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
I got below log after a S3 resume in a ASUS A6VC laptop. The system has
only one IDE drive. It appears there is no reason calling _GTF for
disabled drive.
ACPI Error (dsopcode-0483): Attempt to CreateField of length zero [20070126]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.RATA] (Node df822a7c), AE_AML_OPERAND_VALUE
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.CHN1.DRV0._GTF] (Node df822bd0), AE_AML_OPERAND_VALUE
ata2.00: _GTF evaluation failed (AE 0x3006)
ACPI Error (dsopcode-0483): Attempt to CreateField of length zero [20070126]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.RATA] (Node df822a7c), AE_AML_OPERAND_VALUE
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.CHN1.DRV1._GTF] (Node df822b94), AE_AML_OPERAND_VALUE
ata2.01: _GTF evaluation failed (AE 0x3006)
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_mv does not yet fully support hotplug (coming soon, though).
This means that the driver may not find a Silicon Image port-multiplier
when first loaded, because those devices take in exceess of 3 seconds
to sync up the SATA PHY (most devices do this in mere microseconds).
So, as a short-term interim measure, here we insert a 3-second pause
on initial driver load, once per controller board (not once per port!),
to allow the Silicon Image port-multipliers to be detected later.
This will be removed again (soon!) once hotplug is fully implemented/working.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove unnecessary edma init code from port_start.
This sequence gets done later on the first I/O to the port.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add basic port-multiplier support to sata_mv.
This works in Command-based-switching mode for Gen-II chipsets,
and in FIS-based-switching mode for Gen-IIe chipsets.
Error handling remains at the primary port level for now
(works okay, but not great). This will get fixed in a subsequent
patch series for IRQ/EH handling fixes. There are also some
known NCQ/PMP errata to be dealt with in the near future,
once we have this basic PMP support in place.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The System-On-Chip (SOC) core supports all of the same
features as the other recent Marvell chips,
including NCQ and IRQ coalescing.
Fix the chip_soc flags to enable these capabilities
(note that the driver currently does nothing special
for IRQ coalescing, though).
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Disable hot plug/unplug detection in sata_mv for now.
It is currently broken, and also interferes with PMP support.
This will get fixed in a subsequent patch series.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
More cosmetic cleanups to unclutter the changes needed for PMP support.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rework and simplify sata_mv's hardreset code to take advantage of
libata improvements since it was first coded.
Also, get rid of the now unnecessary prereset, postreset, and phy_reset
functions.
This patch also paves the way for subsequent pmp support patches,
which will follow once this one passes muster.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When no reset method is available, libata currently oopses. Although
the condition can't happen unless there's a bug in a low level driver,
oopsing isn't the best way to report the error condition. Complain,
dump stack and fail reset instead.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We have a certain number of 'ATA' emulations often on CF or other flash
devices that are at best "loosely based" on the CF 1.1 standard. These
devices report themselves as disk but don't support the ATA minimal
command set only the CF 1.1 set.
Relax the PIO checking for devices reporting ATA rev 0, or no iordy
support, or CFA. Rework the code a bit as it was already messy and this
made it quite ugly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The cable detect isolation patch inadvertently removed 40 wire short
cable handling. Put it back
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently, SATA softresets should do link onlineness check before
actually performing SRST protocol but it doesn't really belong to
softreset.
This patch moves onlineness check in softreset to ata_eh_reset() and
ata_eh_followup_srst_needed() to clean up code and help future sata_mv
changes which need clear separation between SCR and TF accesses.
sata_fsl is peculiar in that its softreset really isn't softreset but
combination of hardreset and softreset. This patch adds dummy private
->prereset to keep the current behavior but the driver really should
implement separate hard and soft resets and return -EAGAIN from
hardreset if it should be follwed by softreset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some code paths which had been made obsolete by recent reset
simplification were still around. Kill them.
* ata_eh_reset() checked for ATA_DEV_UNKNOWN to determine
classification failure. This is no longer applicable.
* ata_do_reset() should convert ATA_DEV_UNKNOWN to ATA_DEV_NONE
regardless of reset result (e.g. -EAGAIN).
* LLDs don't need to convert ATA_DEV_UNKNOWN to ATA_DEV_NONE.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/ata/pata_scc.c: In function 'scc_bus_softreset':
drivers/ata/pata_scc.c:594: error: 'deadlien' undeclared (first use in this function)
drivers/ata/pata_scc.c:594: error: (Each undeclared identifier is reported only once
drivers/ata/pata_scc.c:594: error: for each function it appears in.)
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make PMP support optional by adding CONFIG_SATA_PMP and leaving out
libata-pmp.c if it isn't set. PMP helpers return constant values if
PMP support is not enabled and PMP declarations alias non-PMP
counterparts. This makes the compiler to leave out PMP related part
out and LLDs to use non-PMP counterparts automatically.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement helpers to test whether PMP is supported, attached and
determine pmp number to use when issuing SRST to a link. While at it,
move ata_is_host_link() so that it's together with the two new PMP
helpers.
This change simplifies LLDs and helps making PMP support optional.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Most of PMP support code is already in libata-pmp.c. All that are in
libata-core.c are sata_pmp_port_ops and EXPORTs. Move them to
libata-pmp.c. Also, collect PMP related prototypes and declarations
in header files and move them right above of SFF stuff.
This change is to make PMP support optional.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that SFF support is completely separated out from the core layer,
it can be made optional. Add CONFIG_ATA_SFF and let SFF drivers
depend on it. If CONFIG_ATA_SFF isn't set, all codes in libata-sff.c
and data structures for SFF support are disabled. This saves good
number of bytes for small systems.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ap->ioaddr is to carry addresses for TF and BMDMA registers of a SFF
controller, don't abuse it in non-SFF controllers.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Akira Iguchi