Pull networking fixes from David Miller:
1) Various netfilter fixlets from Pablo and the netfilter team.
2) Fix regression in IPVS caused by lack of PMTU exceptions on local
routes in ipv6, from Julian Anastasov.
3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.
4) Don't crash on poll in TLS, from Daniel Borkmann.
5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
including Avahi mDNS. From Bart Van Assche.
6) Missing of_node_put in qcom/emac driver, from Yue Haibing.
7) We lack checking of the TCP checking in one special case during SYN
receive, from Frank van der Linden.
8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.
9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.
10) Must grab HW caps before doing quirk checks in stmmac driver, from
Jose Abreu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
net: stmmac: Run HWIF Quirks after getting HW caps
neighbour: skip NTF_EXT_LEARNED entries during forced gc
net: cxgb3: add error handling for sysfs_create_group
tls: fix waitall behavior in tls_sw_recvmsg
tls: fix use-after-free in tls_push_record
l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
mlxsw: spectrum_switchdev: Fix port_vlan refcounting
mlxsw: spectrum_router: Align with new route replace logic
mlxsw: spectrum_router: Allow appending to dev-only routes
ipv6: Only emit append events for appended routes
stmmac: added support for 802.1ad vlan stripping
cfg80211: fix rcu in cfg80211_unregister_wdev
mac80211: Move up init of TXQs
mac80211_hwsim: fix module init error paths
cfg80211: initialize sinfo in cfg80211_get_station
nl80211: fix some kernel doc tag mistakes
hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
rds: avoid unenecessary cong_update in loop transport
l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
...
Loop transport which is self loopback, remote port congestion
update isn't relevant. Infact the xmit path already ignores it.
Receive path needs to do the same.
Reported-by: syzbot+4c20b3866171ce8441d2@syzkaller.appspotmail.com
Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- bnxt netdev changes merged this cycle caused the bnxt RDMA driver to crash under
certain situations
- Arnd found (several, unfortunately) kconfig problems with the patches adding
INFINIBAND_ADDR_TRANS. Reverting this last part, will fix it more fully
outside -rc.
- Subtle change in error code for a uapi function caused breakage in userspace.
This was bug was subtly introduced cycle
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ppe+
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Just three small last minute regressions that were found in the last
week. The Broadcom fix is a bit big for rc7, but since it is fixing
driver crash regressions that were merged via netdev into rc1, I am
sending it.
- bnxt netdev changes merged this cycle caused the bnxt RDMA driver
to crash under certain situations
- Arnd found (several, unfortunately) kconfig problems with the
patches adding INFINIBAND_ADDR_TRANS. Reverting this last part,
will fix it more fully outside -rc.
- Subtle change in error code for a uapi function caused breakage in
userspace. This was bug was subtly introduced cycle"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/core: Fix error code for invalid GID entry
IB: Revert "remove redundant INFINIBAND kconfig dependencies"
RDMA/bnxt_re: Fix broken RoCE driver due to recent L2 driver changes
Several subsystems depend on INFINIBAND_ADDR_TRANS, which in turn depends
on INFINIBAND. However, when with CONFIG_INIFIBAND=m, this leads to a
link error when another driver using it is built-in. The
INFINIBAND_ADDR_TRANS dependency is insufficient here as this is
a 'bool' symbol that does not force anything to be a module in turn.
fs/cifs/smbdirect.o: In function `smbd_disconnect_rdma_work':
smbdirect.c:(.text+0x1e4): undefined reference to `rdma_disconnect'
net/9p/trans_rdma.o: In function `rdma_request':
trans_rdma.c:(.text+0x7bc): undefined reference to `rdma_disconnect'
net/9p/trans_rdma.o: In function `rdma_destroy_trans':
trans_rdma.c:(.text+0x830): undefined reference to `ib_destroy_qp'
trans_rdma.c:(.text+0x858): undefined reference to `ib_dealloc_pd'
Fixes: 9533b292a7 ("IB: remove redundant INFINIBAND kconfig dependencies")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
- Remove bouncing addresses from the MAINTAINERS file
- Kernel oops and bad error handling fixes for hfi, i40iw, cxgb4, and hns drivers
- Various small LOC behavioral/operational bugs in mlx5, hns, qedr and i40iw drivers
- Two fixes for patches already sent during the merge window
- A long standing bug related to not decreasing the pinned pages count in the right
MM was found and fixed
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=uFZh
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"This is pretty much just the usual array of smallish driver bugs.
- remove bouncing addresses from the MAINTAINERS file
- kernel oops and bad error handling fixes for hfi, i40iw, cxgb4, and
hns drivers
- various small LOC behavioral/operational bugs in mlx5, hns, qedr
and i40iw drivers
- two fixes for patches already sent during the merge window
- a long-standing bug related to not decreasing the pinned pages
count in the right MM was found and fixed"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (28 commits)
RDMA/hns: Move the location for initializing tmp_len
RDMA/hns: Bugfix for cq record db for kernel
IB/uverbs: Fix uverbs_attr_get_obj
RDMA/qedr: Fix doorbell bar mapping for dpi > 1
IB/umem: Use the correct mm during ib_umem_release
iw_cxgb4: Fix an error handling path in 'c4iw_get_dma_mr()'
RDMA/i40iw: Avoid panic when reading back the IRQ affinity hint
RDMA/i40iw: Avoid reference leaks when processing the AEQ
RDMA/i40iw: Avoid panic when objects are being created and destroyed
RDMA/hns: Fix the bug with NULL pointer
RDMA/hns: Set NULL for __internal_mr
RDMA/hns: Enable inner_pa_vld filed of mpt
RDMA/hns: Set desc_dma_addr for zero when free cmq desc
RDMA/hns: Fix the bug with rq sge
RDMA/hns: Not support qp transition from reset to reset for hip06
RDMA/hns: Add return operation when configured global param fail
RDMA/hns: Update convert function of endian format
RDMA/hns: Load the RoCE dirver automatically
RDMA/hns: Bugfix for rq record db for kernel
RDMA/hns: Add rq inline flags judgement
...
INFINIBAND_ADDR_TRANS depends on INFINIBAND. So there's no need for
options which depend INFINIBAND_ADDR_TRANS to also depend on INFINIBAND.
Remove the unnecessary INFINIBAND depends.
Signed-off-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The function rds_ib_setup_qp is calling rds_ib_get_client_data and
should correspondingly call rds_ib_dev_put. This call was lost in
the non-error path with the introduction of error handling done in
commit 3b12f73a5c ("rds: ib: add error handle")
Signed-off-by: Dag Moxnes <dag.moxnes@oracle.com>
Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rds_sendmsg() calls rds_send_mprds_hash() to find a c_path to use to
send a message. Suppose the RDS connection is not yet up. In
rds_send_mprds_hash(), it does
if (conn->c_npaths == 0)
wait_event_interruptible(conn->c_hs_waitq,
(conn->c_npaths != 0));
If it is interrupted before the connection is set up,
rds_send_mprds_hash() will return a non-zero hash value. Hence
rds_sendmsg() will use a non-zero c_path to send the message. But if
the RDS connection ends up to be non-MP capable, the message will be
lost as only the zero c_path can be used.
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronous pernet_operations are not allowed anymore.
All are asynchronous. So, drop the structure member.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netns deletion path does not need to wait for all net_devices
to be unregistered before dismantling rds_tcp state for the netns
(we are able to dismantle this state on module unload even when
all net_devices are active so there is no dependency here).
This patch removes code related to netdevice notifiers and
refactors all the code needed to dismantle rds_tcp state
into a ->exit callback for the pernet_operations used with
register_pernet_device().
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rds_tcp_connection allocation/free management has the potential to be
called from __rds_conn_create after IRQs have been disabled, so
spin_[un]lock_bh cannot be used with rds_tcp_conn_lock.
Bottom-halves that need to synchronize for critical sections protected
by rds_tcp_conn_lock should instead use rds_destroy_pending() correctly.
Reported-by: syzbot+c68e51bb5e699d3f8d91@syzkaller.appspotmail.com
Fixes: ebeeb1ad9b ("rds: tcp: use rds_destroy_pending() to synchronize
netns/module teardown and rds connection/workq management")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations create and destroy sysctl table
and listen socket. Also, exit method flushes global
workqueue and work. Everything looks per-net safe,
so we can mark them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid VLA[1] by using an already allocated buffer passed
by the caller.
[1] https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Salvatore Mesoraca <s.mesoraca16@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid VLA[1] by using an already allocated buffer passed
by the caller.
[1] https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Salvatore Mesoraca <s.mesoraca16@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable sg_off is assigned a value but it is never read, hence it is
redundant and can be removed.
Cleans up clang warning:
net/rds/message.c:373:2: warning: Value stored to 'sg_off' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 9426bbc6de ("rds: use list structure to track information for zerocopy completion notification")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 401910db4c ("rds: deliver zerocopy completion notification
with data") removes support fo r zerocopy completion notification
on the sk_error_queue, thus we no longer need to track the cookie
information in sk_buff structures.
This commit removes the struct sk_buff_head rs_zcookie_queue by
a simpler list that results in a smaller memory footprint as well
as more efficient memory_allocation time.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the large block of code predicated on zcopy from
rds_message_copy_from_user into a new function,
rds_message_zcopy_from_user()
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0933a578cd ("rds: tcp: use sock_create_lite() to create the
accept socket") has a reference counting issue in TCP socket creation
when accepting a new connection. The code uses sock_create_lite() to
create a kernel socket. But it does not do __module_get() on the
socket owner. When the connection is shutdown and sock_release() is
called to free the socket, the owner's reference count is decremented
and becomes incorrect. Note that this bug only shows up when the socket
owner is configured as a kernel module.
v2: Update comments
Fixes: 0933a578cd ("rds: tcp: use sock_create_lite() to create the accept socket")
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit is an optimization over commit 01883eda72
("rds: support for zcopy completion notification") for PF_RDS sockets.
RDS applications are predominantly request-response transactions, so
it is more efficient to reduce the number of system calls and have
zerocopy completion notification delivered as ancillary data on the
POLLIN channel.
Cookies are passed up as ancillary data (at level SOL_RDS) in a
struct rds_zcopy_cookies when the returned value of recvmsg() is
greater than, or equal to, 0. A max of RDS_MAX_ZCOOKIES may be passed
with each message.
This commit removes support for zerocopy completion notification on
MSG_ERRQUEUE for PF_RDS sockets.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if either or both of MSG_ZEROCOPY and SOCK_ZEROCOPY have not been
specified, the rm->data.op_mmp_znotifier allocation will be skipped.
In this case, it is invalid ot pass down a cmsghdr with
RDS_CMSG_ZCOPY_COOKIE, so return EINVAL from rds_msg_zcopy for this
case.
Reported-by: syzbot+f893ae7bb2f6456dfbc3@syzkaller.appspotmail.com
Fixes: 0cebaccef3 ("rds: zerocopy Tx support.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1465362 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the MSG_ZEROCOPY flag is specified with rds_sendmsg(), and,
if the SO_ZEROCOPY socket option has been set on the PF_RDS socket,
application pages sent down with rds_sendmsg() are pinned.
The pinning uses the accounting infrastructure added by
Commit a91dbff551 ("sock: ulimit on MSG_ZEROCOPY pages")
The payload bytes in the message may not be modified for the
duration that the message has been pinned. A multi-threaded
application using this infrastructure may thus need to be notified
about send-completion so that it can free/reuse the buffers
passed to rds_sendmsg(). Notification of send-completion will
identify each message-buffer by a cookie that the application
must specify as ancillary data to rds_sendmsg().
The ancillary data in this case has cmsg_level == SOL_RDS
and cmsg_type == RDS_CMSG_ZCOPY_COOKIE.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDS removes a datagram (rds_message) from the retransmit queue when
an ACK is received. The ACK indicates that the receiver has queued
the RDS datagram, so that the sender can safely forget the datagram.
When all references to the rds_message are quiesced, rds_message_purge
is called to release resources used by the rds_message
If the datagram to be removed had pinned pages set up, add
an entry to the rs->rs_znotify_queue so that the notifcation
will be sent up via rds_rm_zerocopy_callback() when the
rds_message is eventually freed by rds_message_purge.
rds_rm_zerocopy_callback() attempts to batch the number of cookies
sent with each notification to a max of SO_EE_ORIGIN_MAX_ZCOOKIES.
This is achieved by checking the tail skb in the sk_error_queue:
if this has room for one more cookie, the cookie from the
current notification is added; else a new skb is added to the
sk_error_queue. Every invocation of rds_rm_zerocopy_callback() will
trigger a ->sk_error_report to notify the application.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing model holds a reference from the rds_sock to the
rds_message, but the rds_message does not itself hold a sock_put()
on the rds_sock. Instead the m_rs field in the rds_message is
assigned when the message is queued on the sock, and nulled when
the message is dequeued from the sock.
We want to be able to notify userspace when the rds_message
is actually freed (from rds_message_purge(), after the refcounts
to the rds_message go to 0). At the time that rds_message_purge()
is called, the message is no longer on the rds_sock retransmit
queue. Thus the explicit reference for the m_rs is needed to
send a notification that will signal to userspace that
it is now safe to free/reuse any pages that may have
been pinned down for zerocopy.
This patch manages the m_rs assignment in the rds_message with
the necessary refcount book-keeping.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ebeeb1ad9b ("rds: tcp: use rds_destroy_pending() to synchronize
netns/module teardown and rds connection/workq management")
adds an rcu read critical section to __rd_conn_create. The
memory allocations in that critcal section need to use
GFP_ATOMIC to avoid sleeping.
This patch was verified with syzkaller reproducer.
Reported-by: syzbot+a0564419941aaae3fe3c@syzkaller.appspotmail.com
Fixes: ebeeb1ad9b ("rds: tcp: use rds_destroy_pending() to synchronize
netns/module teardown and rds connection/workq management")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes since v1:
Added changes in these files:
drivers/infiniband/hw/usnic/usnic_transport.c
drivers/staging/lustre/lnet/lnet/lib-socket.c
drivers/target/iscsi/iscsi_target_login.c
drivers/vhost/net.c
fs/dlm/lowcomms.c
fs/ocfs2/cluster/tcp.c
security/tomoyo/network.c
Before:
All these functions either return a negative error indicator,
or store length of sockaddr into "int *socklen" parameter
and return zero on success.
"int *socklen" parameter is awkward. For example, if caller does not
care, it still needs to provide on-stack storage for the value
it does not need.
None of the many FOO_getname() functions of various protocols
ever used old value of *socklen. They always just overwrite it.
This change drops this parameter, and makes all these functions, on success,
return length of sockaddr. It's always >= 0 and can be differentiated
from an error.
Tests in callers are changed from "if (err)" to "if (err < 0)", where needed.
rpc_sockname() lost "int buflen" parameter, since its only use was
to be passed to kernel_getsockname() as &buflen and subsequently
not used in any way.
Userspace API is not changed.
text data bss dec hex filename
30108430 2633624 873672 33615726 200ef6e vmlinux.before.o
30108109 2633612 873672 33615393 200ee21 vmlinux.o
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: David S. Miller <davem@davemloft.net>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-decnet-user@lists.sourceforge.net
CC: linux-wireless@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: linux-sctp@vger.kernel.org
CC: linux-nfs@vger.kernel.org
CC: linux-x25@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An rds_connection can get added during netns deletion between lines 528
and 529 of
506 static void rds_tcp_kill_sock(struct net *net)
:
/* code to pull out all the rds_connections that should be destroyed */
:
528 spin_unlock_irq(&rds_tcp_conn_lock);
529 list_for_each_entry_safe(tc, _tc, &tmp_list, t_tcp_node)
530 rds_conn_destroy(tc->t_cpath->cp_conn);
Such an rds_connection would miss out the rds_conn_destroy()
loop (that cancels all pending work) and (if it was scheduled
after netns deletion) could trigger the use-after-free.
A similar race-window exists for the module unload path
in rds_tcp_exit -> rds_tcp_destroy_conns
Concurrency with netns deletion (rds_tcp_kill_sock()) must be handled
by checking check_net() before enqueuing new work or adding new
connections.
Concurrency with module-unload is handled by maintaining a module
specific flag that is set at the start of the module exit function,
and must be checked before enqueuing new work or adding new connections.
This commit refactors existing RDS_DESTROY_PENDING checks added by
commit 3db6e0d172 ("rds: use RCU to synchronize work-enqueue with
connection teardown") and consolidates all the concurrency checks
listed above into the function rds_destroy_pending().
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
- Misc small driver fixups to
bnxt_re/hfi1/qib/hns/ocrdma/rdmavt/vmw_pvrdma/nes
- Several major feature adds to bnxt_re driver: SRIOV VF RoCE support,
HugePages support, extended hardware stats support, and SRQ support
- A notable number of fixes to the i40iw driver from debugging scale up
testing
- More work to enable the new hip08 chip in the hns driver
- Misc small ULP fixups to srp/srpt//ipoib
- Preparation for srp initiator and target to support the RDMA-CM
protocol for connections
- Add RDMA-CM support to srp initiator, srp target is still a WIP
- Fixes for a couple of places where ipoib could spam the dmesg log
- Fix encode/decode of FDR/EDR data rates in the core
- Many patches from Parav with ongoing work to clean up inconsistencies
and bugs in RoCE support around the rdma_cm
- mlx5 driver support for the userspace features 'thread domain', 'wallclock
timestamps' and 'DV Direct Connected transport'. Support for the firmware
dual port rocee capability
- Core support for more than 32 rdma devices in the char dev allocation
- kernel doc updates from Randy Dunlap
- New netlink uAPI for inspecting RDMA objects similar in spirit to 'ss'
- One minor change to the kobject code acked by GKH
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sMXV
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull RDMA subsystem updates from Jason Gunthorpe:
"Overall this cycle did not have any major excitement, and did not
require any shared branch with netdev.
Lots of driver updates, particularly of the scale-up and performance
variety. The largest body of core work was Parav's patches fixing and
restructing some of the core code to make way for future RDMA
containerization.
Summary:
- misc small driver fixups to
bnxt_re/hfi1/qib/hns/ocrdma/rdmavt/vmw_pvrdma/nes
- several major feature adds to bnxt_re driver: SRIOV VF RoCE
support, HugePages support, extended hardware stats support, and
SRQ support
- a notable number of fixes to the i40iw driver from debugging scale
up testing
- more work to enable the new hip08 chip in the hns driver
- misc small ULP fixups to srp/srpt//ipoib
- preparation for srp initiator and target to support the RDMA-CM
protocol for connections
- add RDMA-CM support to srp initiator, srp target is still a WIP
- fixes for a couple of places where ipoib could spam the dmesg log
- fix encode/decode of FDR/EDR data rates in the core
- many patches from Parav with ongoing work to clean up
inconsistencies and bugs in RoCE support around the rdma_cm
- mlx5 driver support for the userspace features 'thread domain',
'wallclock timestamps' and 'DV Direct Connected transport'. Support
for the firmware dual port rocee capability
- core support for more than 32 rdma devices in the char dev
allocation
- kernel doc updates from Randy Dunlap
- new netlink uAPI for inspecting RDMA objects similar in spirit to 'ss'
- one minor change to the kobject code acked by Greg KH"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (259 commits)
RDMA/nldev: Provide detailed QP information
RDMA/nldev: Provide global resource utilization
RDMA/core: Add resource tracking for create and destroy PDs
RDMA/core: Add resource tracking for create and destroy CQs
RDMA/core: Add resource tracking for create and destroy QPs
RDMA/restrack: Add general infrastructure to track RDMA resources
RDMA/core: Save kernel caller name when creating PD and CQ objects
RDMA/core: Use the MODNAME instead of the function name for pd callers
RDMA: Move enum ib_cq_creation_flags to uapi headers
IB/rxe: Change RDMA_RXE kconfig to use select
IB/qib: remove qib_keys.c
IB/mthca: remove mthca_user.h
RDMA/cm: Fix access to uninitialized variable
RDMA/cma: Use existing netif_is_bond_master function
IB/core: Avoid SGID attributes query while converting GID from OPA to IB
RDMA/mlx5: Avoid memory leak in case of XRCD dealloc failure
IB/umad: Fix use of unprotected device pointer
IB/iser: Combine substrings for three messages
IB/iser: Delete an unnecessary variable initialisation in iser_send_data_out()
IB/iser: Delete an error message for a failed memory allocation in iser_send_data_out()
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJabj6pAAoJEHm+PkMAQRiGs8cIAJQFkCWnbz86e3vG4DuWhyA8
CMGHCQdUOxxFGa/ixhIiuetbC0x+JVHAjV2FwVYbAQfaZB3pfw2iR1ncQxpAP1AI
oLU9vBEqTmwKMPc9CM5rRfnLFWpGcGwUNzgPdxD5yYqGDtcM8K840mF6NdkYe5AN
xU8rv1wlcFPF4A5pvHCH0pvVmK4VxlVFk/2H67TFdxBs4PyJOnSBnf+bcGWgsKO6
hC8XIVtcKCH2GfFxt5d0Vgc5QXJEpX1zn2mtCa1MwYRjN2plgYfD84ha0xE7J0B0
oqV/wnjKXDsmrgVpncr3txd4+zKJFNkdNRE4eLAIupHo2XHTG4HvDJ5dBY2NhGU=
=sOml
-----END PGP SIGNATURE-----
Merge tag v4.15 of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
To resolve conflicts in:
drivers/infiniband/hw/mlx5/main.c
drivers/infiniband/hw/mlx5/qp.c
From patches merged into the -rc cycle. The conflict resolution matches
what linux-next has been carrying.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
en_rx_am.c was deleted in 'net-next' but had a bug fixed in it in
'net'.
The esp{4,6}_offload.c conflicts were overlapping changes.
The 'out' label is removed so we just return ERR_PTR(-EINVAL)
directly.
Signed-off-by: David S. Miller <davem@davemloft.net>
rds-tcp uses m_ack_seq to track the tcp ack# that indicates
that the peer has received a rds_message. The m_ack_seq is
used in rds_tcp_is_acked() to figure out when it is safe to
drop the rds_message from the RDS retransmit queue.
The m_ack_seq must be calculated as an offset from the right
edge of the in-flight tcp buffer, i.e., it should be based on
the ->write_seq, not the ->snd_nxt.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the newly introduced rdma_read_gids() to read the SGID and DGID for
the connection which returns GID correctly for RoCE transport as well.
rdma_addr_get_dgid() for RoCE for client side connections returns MAC
address, instead of DGID.
rdma_addr_get_sgid() for RoCE doesn't return correct SGID for IPv6 and
when more than one IP address is assigned to the netdevice.
Therefore use transport agnostic rdma_read_gids() API provided by rdma_cm
module.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
rds_sendmsg() can enqueue work on cp_send_w from process context, but
it should not enqueue this work if connection teardown has commenced
(else we risk enquing work after rds_conn_path_destroy() has assumed that
all work has been cancelled/flushed).
Similarly some other functions like rds_cong_queue_updates
and rds_tcp_data_ready are called in softirq context, and may end
up enqueuing work on rds_wq after rds_conn_path_destroy() has assumed
that all workqs are quiesced.
Check the RDS_DESTROY_PENDING bit and use rcu synchronization to avoid
all these races.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace c_destroy_in_prog by using a bit in cp_flags that
can set/tested atomically.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
set rm->atomic.op_active to 0 when rds_pin_pages() fails
or the user supplied address is invalid,
this prevents a NULL pointer usage in rds_atomic_free_op()
Signed-off-by: Mohamed Ghannam <simo.ghannam@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When args->nr_local is 0, nr_pages gets also 0 due some size
calculation via rds_rm_size(), which is later used to allocate
pages for DMA, this bug produces a heap Out-Of-Bound write access
to a specific memory region.
Signed-off-by: Mohamed Ghannam <simo.ghannam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ip6_gre.c is a case of parallel adds.
include/trace/events/tcp.h is a little bit more tricky. The removal
of in-trace-macro ifdefs in 'net' paralleled with moving
show_tcp_state_name and friends over to include/trace/events/sock.h
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
If kmem_cache_alloc() fails in the middle of the for() loop,
cleanup anything that might have been allocated so far.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f10b4cff98 ("rds: tcp: atomically purge entries from
rds_tcp_conn_list during netns delete") adds the field t_tcp_detached,
but this needs to be initialized explicitly to false.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the rds_sock is not added to the bind_hash_table, we must
reset rs_bound_addr so that rds_remove_bound will not trip on
this rds_sock.
rds_add_bound() does a rds_sock_put() in this failure path, so
failing to reset rs_bound_addr will result in a socket refcount
bug, and will trigger a WARN_ON with the stack shown below when
the application subsequently tries to close the PF_RDS socket.
WARNING: CPU: 20 PID: 19499 at net/rds/af_rds.c:496 \
rds_sock_destruct+0x15/0x30 [rds]
:
__sk_destruct+0x21/0x190
rds_remove_bound.part.13+0xb6/0x140 [rds]
rds_release+0x71/0x120 [rds]
sock_release+0x1a/0x70
sock_close+0xe/0x20
__fput+0xd5/0x210
task_work_run+0x82/0xa0
do_exit+0x2ce/0xb30
? syscall_trace_enter+0x1cc/0x2b0
do_group_exit+0x39/0xa0
SyS_exit_group+0x10/0x10
do_syscall_64+0x61/0x1a0
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDS currently doesn't check if the length of the control message is
large enough to hold the required data, before dereferencing the control
message data. This results in following crash:
BUG: KASAN: stack-out-of-bounds in rds_rdma_bytes net/rds/send.c:1013
[inline]
BUG: KASAN: stack-out-of-bounds in rds_sendmsg+0x1f02/0x1f90
net/rds/send.c:1066
Read of size 8 at addr ffff8801c928fb70 by task syzkaller455006/3157
CPU: 0 PID: 3157 Comm: syzkaller455006 Not tainted 4.15.0-rc3+ #161
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:53
print_address_description+0x73/0x250 mm/kasan/report.c:252
kasan_report_error mm/kasan/report.c:351 [inline]
kasan_report+0x25b/0x340 mm/kasan/report.c:409
__asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:430
rds_rdma_bytes net/rds/send.c:1013 [inline]
rds_sendmsg+0x1f02/0x1f90 net/rds/send.c:1066
sock_sendmsg_nosec net/socket.c:628 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:638
___sys_sendmsg+0x320/0x8b0 net/socket.c:2018
__sys_sendmmsg+0x1ee/0x620 net/socket.c:2108
SYSC_sendmmsg net/socket.c:2139 [inline]
SyS_sendmmsg+0x35/0x60 net/socket.c:2134
entry_SYSCALL_64_fastpath+0x1f/0x96
RIP: 0033:0x43fe49
RSP: 002b:00007fffbe244ad8 EFLAGS: 00000217 ORIG_RAX: 0000000000000133
RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 000000000043fe49
RDX: 0000000000000001 RSI: 000000002020c000 RDI: 0000000000000003
RBP: 00000000006ca018 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000217 R12: 00000000004017b0
R13: 0000000000401840 R14: 0000000000000000 R15: 0000000000000000
To fix this, we verify that the cmsg_len is large enough to hold the
data to be read, before proceeding further.
Reported-by: syzbot <syzkaller-bugs@googlegroups.com>
Signed-off-by: Avinash Repaka <avinash.repaka@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t_name cannot be NULL since it is an array field of a struct.
Replacing null check on static array with string length check using
strnlen()
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rds_tcp_kill_sock() function parses the rds_tcp_conn_list
to find the rds_connection entries marked for deletion as part
of the netns deletion under the protection of the rds_tcp_conn_lock.
Since the rds_tcp_conn_list tracks rds_tcp_connections (which
have a 1:1 mapping with rds_conn_path), multiple tc entries in
the rds_tcp_conn_list will map to a single rds_connection, and will
be deleted as part of the rds_conn_destroy() operation that is
done outside the rds_tcp_conn_lock.
The rds_tcp_conn_list traversal done under the protection of
rds_tcp_conn_lock should not leave any doomed tc entries in
the list after the rds_tcp_conn_lock is released, else another
concurrently executiong netns delete (for a differnt netns) thread
may trip on these entries.
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8edc3affc0 ("rds: tcp: Take explicit refcounts on struct net")
introduces a regression in rds-tcp netns cleanup. The cleanup_net(),
(and thus rds_tcp_dev_event notification) is only called from put_net()
when all netns refcounts go to 0, but this cannot happen if the
rds_connection itself is holding a c_net ref that it expects to
release in rds_tcp_kill_sock.
Instead, the rds_tcp_kill_sock callback should make sure to
tear down state carefully, ensuring that the socket teardown
is only done after all data-structures and workqs that depend
on it are quiesced.
The original motivation for commit 8edc3affc0 ("rds: tcp: Take explicit
refcounts on struct net") was to resolve a race condition reported by
syzkaller where workqs for tx/rx/connect were triggered after the
namespace was deleted. Those worker threads should have been
cancelled/flushed before socket tear-down and indeed,
rds_conn_path_destroy() does try to sequence this by doing
/* cancel cp_send_w */
/* cancel cp_recv_w */
/* flush cp_down_w */
/* free data structures */
Here the "flush cp_down_w" will trigger rds_conn_shutdown and thus
invoke rds_tcp_conn_path_shutdown() to close the tcp socket, so that
we ought to have satisfied the requirement that "socket-close is
done after all other dependent state is quiesced". However,
rds_conn_shutdown has a bug in that it *always* triggers the reconnect
workq (and if connection is successful, we always restart tx/rx
workqs so with the right timing, we risk the race conditions reported
by syzkaller).
Netns deletion is like module teardown- no need to restart a
reconnect in this case. We can use the c_destroy_in_prog bit
to avoid restarting the reconnect.
Fixes: 8edc3affc0 ("rds: tcp: Take explicit refcounts on struct net")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A side-effect of Commit c14b036681 ("rds: tcp: set linger to 1
when unloading a rds-tcp") is that we always send a RST on the tcp
connection for rds_conn_destroy(), so rds_tcp_conn_paths_destroy()
is not needed any more and is removed in this patch.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge updates from Andrew Morton:
- a few misc bits
- ocfs2 updates
- almost all of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (131 commits)
memory hotplug: fix comments when adding section
mm: make alloc_node_mem_map a void call if we don't have CONFIG_FLAT_NODE_MEM_MAP
mm: simplify nodemask printing
mm,oom_reaper: remove pointless kthread_run() error check
mm/page_ext.c: check if page_ext is not prepared
writeback: remove unused function parameter
mm: do not rely on preempt_count in print_vma_addr
mm, sparse: do not swamp log with huge vmemmap allocation failures
mm/hmm: remove redundant variable align_end
mm/list_lru.c: mark expected switch fall-through
mm/shmem.c: mark expected switch fall-through
mm/page_alloc.c: broken deferred calculation
mm: don't warn about allocations which stall for too long
fs: fuse: account fuse_inode slab memory as reclaimable
mm, page_alloc: fix potential false positive in __zone_watermark_ok
mm: mlock: remove lru_add_drain_all()
mm, sysctl: make NUMA stats configurable
shmem: convert shmem_init_inodecache() to void
Unify migrate_pages and move_pages access checks
mm, pagevec: rename pagevec drained field
...
Now that we have a NUMA-aware version of kmalloc_array() we can use it
instead of kmalloc_node() without an overflow check in the size
calculation.
Link: http://lkml.kernel.org/r/20170927082038.3782-7-jthumshirn@suse.de
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Lameter <cl@linux.com>
Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mike Marciniszyn <infinipath@intel.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of unsignaled work-requests posted to the IB send queue is
tracked by a counter in the rds_ib_connection struct. When it reaches
zero, or the caller explicitly asks for it, the send-signaled bit is
set in send_flags and the counter is reset. This is performed by the
rds_ib_set_wr_signal_state() function.
However, this function is not always used which yields inaccurate
accounting. This commit fixes this, re-factors a code bloat related to
the matter, and makes the actual parameter type to the function
consistent.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
send_flags needs to be initialized before calling
rds_ib_set_wr_signal_state().
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use max_1m_mrs/max_8k_mrs while setting max_items, as the former
variables are set based on the underlying device attributes.
Signed-off-by: Avinash Repaka <avinash.repaka@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the scope of has_fr and has_fmr variables as they are
needed only in rds_ib_add_one().
Signed-off-by: Avinash Repaka <avinash.repaka@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rds_send_xmit() there is logic to batch the sends. However, if
another thread has acquired the lock and has incremented the send_gen,
it is considered a race and we yield. The code incrementing the
s_send_lock_queue_raced statistics counter did not count this event
correctly.
This commit counts the race condition correctly.
Changes from v1:
- Removed check for *someone_on_xmit()*
- Fixed incorrect indentation
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reviewed-by: Knut Omang <knut.omang@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bits in m_flags in struct rds_message are used for a plurality of
reasons, and from different contexts. To avoid any missing updates to
m_flags, use the atomic set_bit() instead of the non-atomic equivalent.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reviewed-by: Knut Omang <knut.omang@oracle.com>
Reviewed-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make this const as it is either used during a copy operation or passed
to a const argument of the function rhltable_init
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP offload conflict is dealt with by simply taking what is
in net-next where we have removed all of the UFO handling code
entirely.
The TCP conflict was a case of local variables in a function
being removed from both net and net-next.
In netvsc we had an assignment right next to where a missing
set of u64 stats sync object inits were added.
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 7e3f2952ee ("rds: don't let RDS shutdown a connection
while senders are present"), refilling the receive queue was removed
from rds_ib_recv(), along with the increment of
s_ib_rx_refill_from_thread.
Commit 73ce4317bf ("RDS: make sure we post recv buffers")
re-introduces filling the receive queue from rds_ib_recv(), but does
not add the statistics counter. rds_ib_recv() was later renamed to
rds_ib_recv_path().
This commit reintroduces the statistics counting of
s_ib_rx_refill_from_thread and s_ib_rx_refill_from_cq.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reviewed-by: Knut Omang <knut.omang@oracle.com>
Reviewed-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Reviewed-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDS over IB does not use multipath RDS, so the array
of additional rds_conn_path structures is always superfluous
in this case. Reduce the memory footprint of the rds module
by making this a dynamic allocation predicated on whether
the transport is mp_capable.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Tested-by: Efrain Galaviz <efrain.galaviz@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cp->cp_send_gen is treated as a normal variable, although it may be
used by different threads.
This is fixed by using {READ,WRITE}_ONCE when it is incremented and
READ_ONCE when it is read outside the {acquire,release}_in_xmit
protection.
Normative reference from the Linux-Kernel Memory Model:
Loads from and stores to shared (but non-atomic) variables should
be protected with the READ_ONCE(), WRITE_ONCE(), and
ACCESS_ONCE().
Clause 5.1.2.4/25 in the C standard is also relevant.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reviewed-by: Knut Omang <knut.omang@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We could end up executing rds_conn_shutdown before the rds_recv_worker
thread, then rds_conn_shutdown -> rds_tcp_conn_shutdown can do a
sock_release and set sock->sk to null, which may interleave in bad
ways with rds_recv_worker, e.g., it could result in:
"BUG: unable to handle kernel NULL pointer dereference at 0000000000000078"
[ffff881769f6fd70] release_sock at ffffffff815f337b
[ffff881769f6fd90] rds_tcp_recv at ffffffffa043c888 [rds_tcp]
[ffff881769f6fdb0] rds_recv_worker at ffffffffa04a4810 [rds]
[ffff881769f6fde0] process_one_work at ffffffff810a14c1
[ffff881769f6fe40] worker_thread at ffffffff810a1940
[ffff881769f6fec0] kthread at ffffffff810a6b1e
Also, do not enqueue any new shutdown workq items when the connection is
shutting down (this may happen for rds-tcp in softirq mode, if a FIN
or CLOSE is received while the modules is in the middle of an unload)
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two problems with calling sock_create_kern() from
rds_tcp_accept_one()
1. it sets up a new_sock->sk that is wasteful, because this ->sk
is going to get replaced by inet_accept() in the subsequent ->accept()
2. The new_sock->sk is a leaked reference in sock_graft() which
expects to find a null parent->sk
Avoid these problems by calling sock_create_lite().
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we are unloading the rds_tcp module, we can set linger to 1
and drop pending packets to accelerate reconnect. The peer will
end up resetting the connection based on new generation numbers
of the new incarnation, so hanging on to unsent TCP packets via
linger is mostly pointless in this case.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Jenny Xu <jenny.x.xu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RDS handshake ping probe added by commit 5916e2c155
("RDS: TCP: Enable multipath RDS for TCP") is sent from rds_sendmsg()
before the first data packet is sent to a peer. If the conversation
is not bidirectional (i.e., one side is always passive and never
invokes rds_sendmsg()) and the passive side restarts its rds_tcp
module, a new HS ping probe needs to be sent, so that the number
of paths can be re-established.
This patch achieves that by sending a HS ping probe from
rds_tcp_accept_one() when c_npaths is 0 (i.e., we have not done
a handshake probe with this peer yet).
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Jenny Xu <jenny.x.xu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each time we get an incoming SYN to the RDS_TCP_PORT, the TCP
layer accepts the connection and then the rds_tcp_accept_one()
callback is invoked to process the incoming connection.
rds_tcp_accept_one() may reject the incoming syn for a number of
reasons, e.g., commit 1a0e100fb2 ("RDS: TCP: Force every connection
to be initiated by numerically smaller IP address"), or because
we are getting spammed by a malicious node that is triggering
a flood of connection attempts to RDS_TCP_PORT. If the incoming
syn is rejected, no data would have been sent on the TCP socket,
and we do not need to be in TIME_WAIT state, so we set linger on
the TCP socket before closing, thereby closing the socket efficiently
with a RST.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Imanti Mendez <imanti.mendez@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found when testing between sparc and x86 machines on different
subnets, so the address comparison patterns hit the corner cases and
brought out some bugs fixed by this patch.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Imanti Mendez <imanti.mendez@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 1a0e100fb2 ("RDS: TCP: Force every connection to be
initiated by numerically smaller IP address") we no longer need
the logic associated with cp_outgoing, so clean up usage of this
field.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Imanti Mendez <imanti.mendez@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
Pull iov_iter updates from Al Viro:
"Cleanups that sat in -next + -stable fodder that has just missed 4.11.
There's more iov_iter work in my local tree, but I'd prefer to push
the stuff that had been in -next first"
* 'work.iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
iov_iter: don't revert iov buffer if csum error
generic_file_read_iter(): make use of iov_iter_revert()
generic_file_direct_write(): make use of iov_iter_revert()
orangefs: use iov_iter_revert()
sctp: switch to copy_from_iter_full()
net/9p: switch to copy_from_iter_full()
switch memcpy_from_msg() to copy_from_iter_full()
rds: make use of iov_iter_revert()
The rds_connect_worker() has a bug in the check that enforces the
canonical connection order described in the comments of
rds_tcp_state_change(). The intention is to make sure that all
the multipath connections are always initiated by the smaller IP
address via rds_start_mprds. To achieve this, rds_connection_worker
should check that cp_index > 0.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rds_conn_shutdown() runs in workq context, and marks the rds_connection
as DISCONNECTING before quiescing Tx/Rx paths. However, after all I/O
has quiesced, we may still find the rds_connection state to be
RDS_CONN_ERROR if an intervening FIN was processed in softirq context.
This is not a fatal error: rds_conn_shutdown() should continue the
shutdown, and there is no need to log noisy messages about this event.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmgenet.c
net/core/sock.c
Conflicts were overlapping changes in bcmgenet and the
lockdep handling of sockets.
Signed-off-by: David S. Miller <davem@davemloft.net>
When some errors occur, the scatter/gather list mapped to DMA addresses
should be handled.
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function rds_ib_map_fmr is used only in the ib_fmr.c
file. As such, the static type is added to limit it in this file.
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function ib_dealloc_fmr will never be called. As such, it should
be removed.
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rdma_accept fails, rdma_reject is called in it. As such, it is
not necessary to execute rdma_reject again.
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lockdep issues a circular dependency warning when AFS issues an operation
through AF_RXRPC from a context in which the VFS/VM holds the mmap_sem.
The theory lockdep comes up with is as follows:
(1) If the pagefault handler decides it needs to read pages from AFS, it
calls AFS with mmap_sem held and AFS begins an AF_RXRPC call, but
creating a call requires the socket lock:
mmap_sem must be taken before sk_lock-AF_RXRPC
(2) afs_open_socket() opens an AF_RXRPC socket and binds it. rxrpc_bind()
binds the underlying UDP socket whilst holding its socket lock.
inet_bind() takes its own socket lock:
sk_lock-AF_RXRPC must be taken before sk_lock-AF_INET
(3) Reading from a TCP socket into a userspace buffer might cause a fault
and thus cause the kernel to take the mmap_sem, but the TCP socket is
locked whilst doing this:
sk_lock-AF_INET must be taken before mmap_sem
However, lockdep's theory is wrong in this instance because it deals only
with lock classes and not individual locks. The AF_INET lock in (2) isn't
really equivalent to the AF_INET lock in (3) as the former deals with a
socket entirely internal to the kernel that never sees userspace. This is
a limitation in the design of lockdep.
Fix the general case by:
(1) Double up all the locking keys used in sockets so that one set are
used if the socket is created by userspace and the other set is used
if the socket is created by the kernel.
(2) Store the kern parameter passed to sk_alloc() in a variable in the
sock struct (sk_kern_sock). This informs sock_lock_init(),
sock_init_data() and sk_clone_lock() as to the lock keys to be used.
Note that the child created by sk_clone_lock() inherits the parent's
kern setting.
(3) Add a 'kern' parameter to ->accept() that is analogous to the one
passed in to ->create() that distinguishes whether kernel_accept() or
sys_accept4() was the caller and can be passed to sk_alloc().
Note that a lot of accept functions merely dequeue an already
allocated socket. I haven't touched these as the new socket already
exists before we get the parameter.
Note also that there are a couple of places where I've made the accepted
socket unconditionally kernel-based:
irda_accept()
rds_rcp_accept_one()
tcp_accept_from_sock()
because they follow a sock_create_kern() and accept off of that.
Whilst creating this, I noticed that lustre and ocfs don't create sockets
through sock_create_kern() and thus they aren't marked as for-kernel,
though they appear to be internal. I wonder if these should do that so
that they use the new set of lock keys.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the function rds_ib_setup_qp, the error handle is missing. When some
error occurs, it is possible that memory leak occurs. As such, error
handle is added.
Cc: Joe Jin <joe.jin@oracle.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Guanglei Li <guanglei.li@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a93d01f577 ("RDS: TCP: avoid bad page reference in
rds_tcp_listen_data_ready") added the function
rds_tcp_listen_sock_def_readable() to handle the case when a
partially set-up acceptor socket drops into rds_tcp_listen_data_ready().
However, if the listen socket (rtn->rds_tcp_listen_sock) is itself going
through a tear-down via rds_tcp_listen_stop(), the (*ready)() will be
null and we would hit a panic of the form
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: (null)
:
? rds_tcp_listen_data_ready+0x59/0xb0 [rds_tcp]
tcp_data_queue+0x39d/0x5b0
tcp_rcv_established+0x2e5/0x660
tcp_v4_do_rcv+0x122/0x220
tcp_v4_rcv+0x8b7/0x980
:
In the above case, it is not fatal to encounter a NULL value for
ready- we should just drop the packet and let the flush of the
acceptor thread finish gracefully.
In general, the tear-down sequence for listen() and accept() socket
that is ensured by this commit is:
rtn->rds_tcp_listen_sock = NULL; /* prevent any new accepts */
In rds_tcp_listen_stop():
serialize with, and prevent, further callbacks using lock_sock()
flush rds_wq
flush acceptor workq
sock_release(listen socket)
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Order of initialization in rds_tcp_init needs to be done so
that resources are set up and destroyed in the correct synchronization
sequence with both the data path, as well as netns create/destroy
path. Specifically,
- we must call register_pernet_subsys and get the rds_tcp_netid
before calling register_netdevice_notifier, otherwise we risk
the sequence
1. register_netdevice_notifier sets up netdev notifier callback
2. rds_tcp_dev_event -> rds_tcp_kill_sock uses netid 0, and finds
the wrong rtn, resulting in a panic with string that is of the form:
BUG: unable to handle kernel NULL pointer dereference at 000000000000000d
IP: rds_tcp_kill_sock+0x3a/0x1d0 [rds_tcp]
:
- the rds_tcp_incoming_slab kmem_cache must be initialized before the
datapath starts up. The latter can happen any time after the
pernet_subsys registration of rds_tcp_net_ops, whose -> init
function sets up the listen socket. If the rds_tcp_incoming_slab has
not been set up at that time, a panic of the form below may be
encountered
BUG: unable to handle kernel NULL pointer dereference at 0000000000000014
IP: kmem_cache_alloc+0x90/0x1c0
:
rds_tcp_data_recv+0x1e7/0x370 [rds_tcp]
tcp_read_sock+0x96/0x1c0
rds_tcp_recv_path+0x65/0x80 [rds_tcp]
:
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is incorrect for the rds_connection to piggyback on the
sock_net() refcount for the netns because this gives rise to
a chicken-and-egg problem during rds_conn_destroy. Instead explicitly
take a ref on the net, and hold the netns down till the connection
tear-down is complete.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix double-free in batman-adv, from Sven Eckelmann.
2) Fix packet stats for fast-RX path, from Joannes Berg.
3) Netfilter's ip_route_me_harder() doesn't handle request sockets
properly, fix from Florian Westphal.
4) Fix sendmsg deadlock in rxrpc, from David Howells.
5) Add missing RCU locking to transport hashtable scan, from Xin Long.
6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.
7) Fix race in NAPI handling between poll handlers and busy polling,
from Eric Dumazet.
8) TX path in vxlan and geneve need proper RCU locking, from Jakub
Kicinski.
9) SYN processing in DCCP and TCP need to disable BH, from Eric
Dumazet.
10) Properly handle net_enable_timestamp() being invoked from IRQ
context, also from Eric Dumazet.
11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.
12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
Melo.
13) Fix use-after-free in netvsc driver, from Dexuan Cui.
14) Fix max MTU setting in bonding driver, from WANG Cong.
15) xen-netback hash table can be allocated from softirq context, so use
GFP_ATOMIC. From Anoob Soman.
16) Fix MAC address change bug in bgmac driver, from Hari Vyas.
17) strparser needs to destroy strp_wq on module exit, from WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
strparser: destroy workqueue on module exit
sfc: fix IPID endianness in TSOv2
sfc: avoid max() in array size
rds: remove unnecessary returned value check
rxrpc: Fix potential NULL-pointer exception
nfp: correct DMA direction in XDP DMA sync
nfp: don't tell FW about the reserved buffer space
net: ethernet: bgmac: mac address change bug
net: ethernet: bgmac: init sequence bug
xen-netback: don't vfree() queues under spinlock
xen-netback: keep a local pointer for vif in backend_disconnect()
netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
netfilter: nf_conntrack_sip: fix wrong memory initialisation
can: flexcan: fix typo in comment
can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
can: gs_usb: fix coding style
can: gs_usb: Don't use stack memory for USB transfers
ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
ixgbe: update the rss key on h/w, when ethtool ask for it
...
The function rds_trans_register always returns 0. As such, it is not
necessary to check the returned value.
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs sendmsg updates from Al Viro:
"More sendmsg work.
This is a fairly separate isolated stuff (there's a continuation
around lustre, but that one was too late to soak in -next), thus the
separate pull request"
* 'work.sendmsg' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ncpfs: switch to sock_sendmsg()
ncpfs: don't mess with manually advancing iovec on send
ncpfs: sendmsg does *not* bugger iovec these days
ceph_tcp_sendpage(): use ITER_BVEC sendmsg
afs_send_pages(): use ITER_BVEC
rds: remove dead code
ceph: switch to sock_recvmsg()
usbip_recv(): switch to sock_recvmsg()
iscsi_target: deal with short writes on the tx side
[nbd] pass iov_iter to nbd_xmit()
[nbd] switch sock_xmit() to sock_{send,recv}msg()
[drbd] use sock_sendmsg()
The variables rds_ib_mr_1m_pool_size and rds_ib_mr_8k_pool_size
are used only in the ib.c file. As such, the static type is
added to limit them in this file.
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Don't save TIPC header values before the header has been validated,
from Jon Paul Maloy.
2) Fix memory leak in RDS, from Zhu Yanjun.
3) We miss to initialize the UID in the flow key in some paths, from
Julian Anastasov.
4) Fix latent TOS masking bug in the routing cache removal from years
ago, also from Julian.
5) We forget to set the sockaddr port in sctp_copy_local_addr_list(),
fix from Xin Long.
6) Missing module ref count drop in packet scheduler actions, from
Roman Mashak.
7) Fix RCU annotations in rht_bucket_nested, from Herbert Xu.
8) Fix use after free which happens because L2TP's ipv4 support returns
non-zero values from it's backlog_rcv function which ipv4 interprets
as protocol values. Fix from Paul Hüber.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
qed: Don't use attention PTT for configuring BW
qed: Fix race with multiple VFs
l2tp: avoid use-after-free caused by l2tp_ip_backlog_recv
xfrm: provide correct dst in xfrm_neigh_lookup
rhashtable: Fix RCU dereference annotation in rht_bucket_nested
rhashtable: Fix use before NULL check in bucket_table_free
net sched actions: do not overwrite status of action creation.
rxrpc: Kernel calls get stuck in recvmsg
net sched actions: decrement module reference count after table flush.
lib: Allow compile-testing of parman
ipv6: check sk sk_type and protocol early in ip_mroute_set/getsockopt
sctp: set sin_port for addr param when checking duplicate address
net/mlx4_en: fix overflow in mlx4_en_init_timestamp()
netfilter: nft_set_bitmap: incorrect bitmap size
net: s2io: fix typo argumnet argument
net: vxge: fix typo argumnet argument
netfilter: nf_ct_expect: Change __nf_ct_expect_check() return value.
ipv4: mask tos for input route
ipv4: add missing initialization for flowi4_uid
lib: fix spelling mistake: "actualy" -> "actually"
...
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes
it was possible to remove the IB DMA mapping code entirely and
switch the RDMA stack to use the core DMA mapping code. This resulted
in a nice set of cleanups, but touched the entire tree. This branch
will be submitted separately to Linus at the end of the merge window
as per normal practice for tree wide changes like this.
-----BEGIN PGP SIGNATURE-----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=e0Si
-----END PGP SIGNATURE-----
Merge tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma DMA mapping updates from Doug Ledford:
"Drop IB DMA mapping code and use core DMA code instead.
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes it
was possible to remove the IB DMA mapping code entirely and switch the
RDMA stack to use the core DMA mapping code.
This resulted in a nice set of cleanups, but touched the entire tree
and has been kept separate for that reason."
* tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (37 commits)
IB/rxe, IB/rdmavt: Use dma_virt_ops instead of duplicating it
IB/core: Remove ib_device.dma_device
nvme-rdma: Switch from dma_device to dev.parent
RDS: net: Switch from dma_device to dev.parent
IB/srpt: Modify a debug statement
IB/srp: Switch from dma_device to dev.parent
IB/iser: Switch from dma_device to dev.parent
IB/IPoIB: Switch from dma_device to dev.parent
IB/rxe: Switch from dma_device to dev.parent
IB/vmw_pvrdma: Switch from dma_device to dev.parent
IB/usnic: Switch from dma_device to dev.parent
IB/qib: Switch from dma_device to dev.parent
IB/qedr: Switch from dma_device to dev.parent
IB/ocrdma: Switch from dma_device to dev.parent
IB/nes: Remove a superfluous assignment statement
IB/mthca: Switch from dma_device to dev.parent
IB/mlx5: Switch from dma_device to dev.parent
IB/mlx4: Switch from dma_device to dev.parent
IB/i40iw: Remove a superfluous assignment statement
IB/hns: Switch from dma_device to dev.parent
...
When the function register_netdevice_notifier fails, the memory
allocated by kmem_cache_create should be freed by the function
kmem_cache_destroy.
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/rds/ib.c:115:2-7: WARNING: NULL check before freeing functions like kfree, debugfs_remove, debugfs_remove_recursive or usb_free_urb is not needed. Maybe consider reorganizing relevant code to avoid passing NULL values.
NULL check before some freeing functions is not needed.
Based on checkpatch warning
"kfree(NULL) is safe this check is probably not required"
and kfreeaddr.cocci by Julia Lawall.
Generated by: scripts/coccinelle/free/ifnullfree.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the function rds_ib_xmit_atomic, ib_ring is not allocated
successfully. As such, it is not necessary to unalloc it.
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the type of the dma_handle argument from u64 * to dma_addr_t *.
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Larger than supported value can lead to array read/write overflow.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Socket option to tap receive path latency in various stages
in nano seconds. It can be enabled on selective sockets using
using SO_RDS_MSG_RXPATH_LATENCY socket option. RDS will return
the data to application with RDS_CMSG_RXPATH_LATENCY in defined
format. Scope is left to add more trace points for future
without need of change in the interface.
Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
RDS support max message size as 1M but the code doesn't check this
in all cases. Patch fixes it for RDMA & non-RDMA and RDS MR size
and its enforced irrespective of underlying transport.
Signed-off-by: Avinash Repaka <avinash.repaka@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Tracks the receive side memory added to scokets and removed from sockets.
Signed-off-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Shutdown code reaping loop takes care of emptying the
CQ's before they being destroyed. And once tasklets are
killed, the hanlders are not expected to run.
But because of core tasklet code issues, tasklet handler could
still run even after tasklet_kill,
RDS IB shutdown code already reaps the CQs before freeing
cq/qp resources so as such the handlers have nothing left
to do post shutdown.
On other hand any handler running after teardown and trying
to access already freed qp/cq resources causes issues
Patch fixes this race by makes sure that handlers returns
without any action post teardown.
Reviewed-by: Wengang <wen.gang.wang@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
When application sends an RDS RDMA composite message consist of
RDMA transfer to be followed up by non RDMA payload, it expect to
be notified *only* when the full message gets delivered. RDS RDMA
notification doesn't behave this way though.
Thanks to Venkat for debug and root casuing the issue
where only first part of the message(RDMA) was
successfully delivered but remainder payload delivery failed.
In that case, application should not be notified with
a false positive of message delivery success.
Fix this case by making sure the user gets notified only after
the full message delivery.
Reviewed-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Based on available device vectors, allocate cqs accordingly to
get better spread of completion vectors which helps performace
great deal..
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
In absence of extension headers, message log will keep
flooding the console. As such even without use_once we can
clean up the MRs so its not really an error case message
so make it debug message
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
MR invalidation in RDS is done in background thread and not in
data path like registration. So break the dependency between them
which helps to remove the performance bottleneck.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The first message to a remote node should prompt a new
connection even if it is RDMA operation. For RDMA operation
the MR mapping can fail because connections is not yet up.
Since the connection establishment is asynchronous,
we make sure the map failure because of unavailable
connection reach to the user by appropriate error code.
Before returning to the user, lets trigger the connection
so that its ready for the next retry.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Transport retry is not much useful since it indicate packet loss
in fabric so its better to failover fast rather than longer retry.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Fixes below warnings:
warning: symbol 'rds_send_probe' was not declared. Should it be static?
warning: symbol 'rds_send_ping' was not declared. Should it be static?
warning: symbol 'rds_tcp_accept_one_path' was not declared. Should it be static?
warning: symbol 'rds_walk_conn_path_info' was not declared. Should it be static?
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
It's useful to know the IP address when RDS fails to bind a
connection. Thus, adding it to the error message.
Orabug: 21894138
Reviewed-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
To make the code clearer, use rb_entry() instead of container_of() to
deal with rbtree.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Shared mlx5 updates with net stack (will drop out on merge if Dave's
tree has already been merged)
- Driver updates: cxgb4, hfi1, hns-roce, i40iw, mlx4, mlx5, qedr, rxe
- Debug cleanups
- New connection rejection helpers
- SRP updates
- Various misc fixes
- New paravirt driver from vmware
-----BEGIN PGP SIGNATURE-----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=QeGy
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is the complete update for the rdma stack for this release cycle.
Most of it is typical driver and core updates, but there is the
entirely new VMWare pvrdma driver. You may have noticed that there
were changes in DaveM's pull request to the bnxt Ethernet driver to
support a RoCE RDMA driver. The bnxt_re driver was tentatively set to
be pulled in this release cycle, but it simply wasn't ready in time
and was dropped (a few review comments still to address, and some
multi-arch build issues like prefetch() not working across all
arches).
Summary:
- shared mlx5 updates with net stack (will drop out on merge if
Dave's tree has already been merged)
- driver updates: cxgb4, hfi1, hns-roce, i40iw, mlx4, mlx5, qedr, rxe
- debug cleanups
- new connection rejection helpers
- SRP updates
- various misc fixes
- new paravirt driver from vmware"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (210 commits)
IB: Add vmw_pvrdma driver
IB/mlx4: fix improper return value
IB/ocrdma: fix bad initialization
infiniband: nes: return value of skb_linearize should be handled
MAINTAINERS: Update Intel RDMA RNIC driver maintainers
MAINTAINERS: Remove Mitesh Ahuja from emulex maintainers
IB/core: fix unmap_sg argument
qede: fix general protection fault may occur on probe
IB/mthca: Replace pci_pool_alloc by pci_pool_zalloc
mlx5, calc_sq_size(): Make a debug message more informative
mlx5: Remove a set-but-not-used variable
mlx5: Use { } instead of { 0 } to init struct
IB/srp: Make writing the add_target sysfs attr interruptible
IB/srp: Make mapping failures easier to debug
IB/srp: Make login failures easier to debug
IB/srp: Introduce a local variable in srp_add_one()
IB/srp: Fix CONFIG_DYNAMIC_DEBUG=n build
IB/multicast: Check ib_find_pkey() return value
IPoIB: Avoid reading an uninitialized member variable
IB/mad: Fix an array index check
...
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
If some error is encountered in rds_tcp_init_net, make sure to
unregister_netdevice_notifier(), else we could trigger a panic
later on, when the modprobe from a netns fails.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make struct pernet_operations::id unsigned.
There are 2 reasons to do so:
1)
This field is really an index into an zero based array and
thus is unsigned entity. Using negative value is out-of-bound
access by definition.
2)
On x86_64 unsigned 32-bit data which are mixed with pointers
via array indexing or offsets added or subtracted to pointers
are preffered to signed 32-bit data.
"int" being used as an array index needs to be sign-extended
to 64-bit before being used.
void f(long *p, int i)
{
g(p[i]);
}
roughly translates to
movsx rsi, esi
mov rdi, [rsi+...]
call g
MOVSX is 3 byte instruction which isn't necessary if the variable is
unsigned because x86_64 is zero extending by default.
Now, there is net_generic() function which, you guessed it right, uses
"int" as an array index:
static inline void *net_generic(const struct net *net, int id)
{
...
ptr = ng->ptr[id - 1];
...
}
And this function is used a lot, so those sign extensions add up.
Patch snipes ~1730 bytes on allyesconfig kernel (without all junk
messing with code generation):
add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730)
Unfortunately some functions actually grow bigger.
This is a semmingly random artefact of code generation with register
allocator being used differently. gcc decides that some variable
needs to live in new r8+ registers and every access now requires REX
prefix. Or it is shifted into r12, so [r12+0] addressing mode has to be
used which is longer than [r8]
However, overall balance is in negative direction:
add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730)
function old new delta
nfsd4_lock 3886 3959 +73
tipc_link_build_proto_msg 1096 1140 +44
mac80211_hwsim_new_radio 2776 2808 +32
tipc_mon_rcv 1032 1058 +26
svcauth_gss_legacy_init 1413 1429 +16
tipc_bcbase_select_primary 379 392 +13
nfsd4_exchange_id 1247 1260 +13
nfsd4_setclientid_confirm 782 793 +11
...
put_client_renew_locked 494 480 -14
ip_set_sockfn_get 730 716 -14
geneve_sock_add 829 813 -16
nfsd4_sequence_done 721 703 -18
nlmclnt_lookup_host 708 686 -22
nfsd4_lockt 1085 1063 -22
nfs_get_client 1077 1050 -27
tcf_bpf_init 1106 1076 -30
nfsd4_encode_fattr 5997 5930 -67
Total: Before=154856051, After=154854321, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 2 RDS peers initiate an RDS-TCP connection simultaneously,
there is a potential for "duelling syns" on either/both sides.
See commit 241b271952 ("RDS-TCP: Reset tcp callbacks if re-using an
outgoing socket in rds_tcp_accept_one()") for a description of this
condition, and the arbitration logic which ensures that the
numerically large IP address in the TCP connection is bound to the
RDS_TCP_PORT ("canonical ordering").
The rds_connection should not be marked as RDS_CONN_UP until the
arbitration logic has converged for the following reason. The sender
may start transmitting RDS datagrams as soon as RDS_CONN_UP is set,
and since the sender removes all datagrams from the rds_connection's
cp_retrans queue based on TCP acks. If the TCP ack was sent from
a tcp socket that got reset as part of duel aribitration (but
before data was delivered to the receivers RDS socket layer),
the sender may end up prematurely freeing the datagram, and
the datagram is no longer reliably deliverable.
This patch remedies that condition by making sure that, upon
receipt of 3WH completion state change notification of TCP_ESTABLISHED
in rds_tcp_state_change, we mark the rds_connection as RDS_CONN_UP
if, and only if, the IP addresses and ports for the connection are
canonically ordered. In all other cases, rds_tcp_state_change will
force an rds_conn_path_drop(), and rds_queue_reconnect() on
both peers will restart the connection to ensure canonical ordering.
A side-effect of enforcing this condition in rds_tcp_state_change()
is that rds_tcp_accept_one_path() can now be refactored for simplicity.
It is also no longer possible to encounter an RDS_CONN_UP connection in
the arbitration logic in rds_tcp_accept_one().
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RDS transport has to be able to distinguish between
two types of failure events:
(a) when the transport fails (e.g., TCP connection reset)
but the RDS socket/connection layer on both sides stays
the same
(b) when the peer's RDS layer itself resets (e.g., due to module
reload or machine reboot at the peer)
In case (a) both sides must reconnect and continue the RDS messaging
without any message loss or disruption to the message sequence numbers,
and this is achieved by rds_send_path_reset().
In case (b) we should reset all rds_connection state to the
new incarnation of the peer. Examples of state that needs to
be reset are next expected rx sequence number from, or messages to be
retransmitted to, the new incarnation of the peer.
To achieve this, the RDS handshake probe added as part of
commit 5916e2c155 ("RDS: TCP: Enable multipath RDS for TCP")
is enhanced so that sender and receiver of the RDS ping-probe
will add a generation number as part of the RDS_EXTHDR_GEN_NUM
extension header. Each peer stores local and remote generation
numbers as part of each rds_connection. Changes in generation
number will be detected via incoming handshake probe ping
request or response and will allow the receiver to reset rds_connection
state.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted in rds_recv_incoming() sequence numbers on data packets
can decreas for the failover case, and the Rx path is equipped
to recover from this, if the RDS_FLAG_RETRANSMITTED is set
on the rds header of an incoming message with a suspect sequence
number.
The RDS_FLAG_RETRANSMITTED is predicated on the RDS_FLAG_RETRANSMITTED
flag in the rds_message, so make sure the flag is set on messages
queued for retransmission.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds