The mcount record method of ftrace scans objdump for references to mcount.
Using mcount as the reference to test if the calls to mcount being replaced
are indeed calls to mcount, this use of mcount was also caught as a
location to change. Using a variable that points to the mcount address
moves this reference into the data section that is not scanned, and
we do not use a false location to try and modify.
The warn on code was what was used to detect this bug.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is another tracer using the ftrace infrastructure, that examines
at each function call the size of the stack. If the stack use is greater
than the previous max it is recorded.
You can always see (and set) the max stack size seen. By setting it
to zero will start the recording again. The backtrace is also available.
For example:
# cat /debug/tracing/stack_max_size
1856
# cat /debug/tracing/stack_trace
[<c027764d>] stack_trace_call+0x8f/0x101
[<c021b966>] ftrace_call+0x5/0x8
[<c02553cc>] clocksource_get_next+0x12/0x48
[<c02542a5>] update_wall_time+0x538/0x6d1
[<c0245913>] do_timer+0x23/0xb0
[<c0257657>] tick_do_update_jiffies64+0xd9/0xf1
[<c02576b9>] tick_sched_timer+0x4a/0xad
[<c0250fe6>] __run_hrtimer+0x3e/0x75
[<c02518ed>] hrtimer_interrupt+0xf1/0x154
[<c022c870>] smp_apic_timer_interrupt+0x71/0x84
[<c021b7e9>] apic_timer_interrupt+0x2d/0x34
[<c0238597>] finish_task_switch+0x29/0xa0
[<c05abd13>] schedule+0x765/0x7be
[<c05abfca>] schedule_timeout+0x1b/0x90
[<c05ab4d4>] wait_for_common+0xab/0x101
[<c05ab5ac>] wait_for_completion+0x12/0x14
[<c033cfc3>] blk_execute_rq+0x84/0x99
[<c0402470>] scsi_execute+0xc2/0x105
[<c040250a>] scsi_execute_req+0x57/0x7f
[<c043afe0>] sr_test_unit_ready+0x3e/0x97
[<c043bbd6>] sr_media_change+0x43/0x205
[<c046b59f>] media_changed+0x48/0x77
[<c046b5ff>] cdrom_media_changed+0x31/0x37
[<c043b091>] sr_block_media_changed+0x16/0x18
[<c02b9e69>] check_disk_change+0x1b/0x63
[<c046f4c3>] cdrom_open+0x7a1/0x806
[<c043b148>] sr_block_open+0x78/0x8d
[<c02ba4c0>] do_open+0x90/0x257
[<c02ba869>] blkdev_open+0x2d/0x56
[<c0296a1f>] __dentry_open+0x14d/0x23c
[<c0296b32>] nameidata_to_filp+0x24/0x38
[<c02a1c68>] do_filp_open+0x347/0x626
[<c02967ef>] do_sys_open+0x47/0xbc
[<c02968b0>] sys_open+0x23/0x2b
[<c021aadd>] sysenter_do_call+0x12/0x26
I've tested this on both x86_64 and i386.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After disabling FTRACE_MCOUNT_RECORD via a patch, a dormant build
failure surfaced:
kernel/trace/ftrace.c: In function 'ftrace_record_ip':
kernel/trace/ftrace.c:416: error: incompatible type for argument 1 of '_spin_lock_irqsave'
kernel/trace/ftrace.c:433: error: incompatible type for argument 1 of '_spin_lock_irqsave'
Introduced by commit 6dad8e07f4c10b17b038e84d29f3ca41c2e55cd0 ("ftrace:
add necessary locking for ftrace records").
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The new design of pre-recorded mcounts and updating the code outside of
kstop_machine has changed the way the records themselves are protected.
This patch uses the ftrace_lock to protect the records. Note, the lock
still does not need to be taken within calls that are only called via
kstop_machine, since the that code can not run while the spin lock is held.
Also removed the hash_lock needed for the daemon when MCOUNT_RECORD is
configured. Also did a slight cleanup of an unused variable.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If one of the self tests of ftrace has disabled the function tracer,
do not run the code to convert the mcount calls in modules.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes some mistakes on the tracer in warning messages when
debugfs fails to create tracing files.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: srostedt@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
At OLS I had a lot of interest to be able to have the ftrace buffers
dumped on panic. Usually one would expect to uses kexec and examine
the buffers after a new kernel is loaded. But sometimes the resources
do not permit kdump and kexec, so having an option to still see the
sequence of events up to the crash is very advantageous.
This patch adds the option to have the ftrace buffers dumped to the
console in the latency_trace format on a panic. When the option is set,
the default entries per CPU buffer are lowered to 16384, since the writing
to the serial (if that is the console) may take an awful long time
otherwise.
[
Changes since -v1:
Got alpine to send correctly (as well as spell check working).
Removed config option.
Moved the static variables into ftrace_dump itself.
Gave printk a log level.
]
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Based on Randy Dunlap's suggestion, the ftrace_printk kernel-doc belongs
with the ftrace_printk macro that should be used. Not with the
__ftrace_printk internal function.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds a feature that can help kernel developers debug their
code using ftrace.
int ftrace_printk(const char *fmt, ...);
This records into the ftrace buffer using printf formatting. The entry
size in the buffers are still a fixed length. A new type has been added
that allows for more entries to be used for a single recording.
The start of the print is still the same as the other entries.
It returns the number of characters written to the ftrace buffer.
For example:
Having a module with the following code:
static int __init ftrace_print_test(void)
{
ftrace_printk("jiffies are %ld\n", jiffies);
return 0;
}
Gives me:
insmod-5441 3...1 7569us : ftrace_print_test: jiffies are 4296626666
for the latency_trace file and:
insmod-5441 [03] 1959.370498: ftrace_print_test jiffies are 4296626666
for the trace file.
Note: Only the infrastructure should go into the kernel. It is to help
facilitate debugging for other kernel developers. Calls to ftrace_printk
is not intended to be left in the kernel, and should be frowned upon just
like scattering printks around in the code.
But having this easily at your fingertips helps the debugging go faster
and bugs be solved quicker.
Maybe later on, we can hook this with markers and have their printf format
be sucked into ftrace output.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some tracers will need to work with more than one entry. In order to do this
the trace_entry structure was split into two fields. One for the start of
all entries, and one to continue an existing entry.
The trace_entry structure now has a "field" entry that consists of the previous
content of the trace_entry, and a "cont" entry that is just a string buffer
the size of the "field" entry.
Thanks to Andrew Morton for suggesting this idea.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When a mcount pointer is recorded into a table, it is used to add or
remove calls to mcount (replacing them with nops). If the code is removed
via removing a module, the pointers still exist. At modifying the code
a check is always made to make sure the code being replaced is the code
expected. In-other-words, the code being replaced is compared to what
it is expected to be before being replaced.
There is a very small chance that the code being replaced just happens
to look like code that calls mcount (very small since the call to mcount
is relative). To remove this chance, this patch adds ftrace_release to
allow module unloading to remove the pointers to mcount within the module.
Another change for init calls is made to not trace calls marked with
__init. The tracing can not be started until after init is done anyway.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Seems that freed records can appear in the available_filter_functions list.
This patch fixes that.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch enables the loading of the __mcount_section of modules and
changing all the callers of mcount into nops.
The modification is done before the init_module function is called, so
again, we do not need to use kstop_machine to make these changes.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is the infrastructure to the converting the mcount call sites
recorded by the __mcount_loc section into nops on boot. It also allows
for using these sites to enable tracing as normal. When the __mcount_loc
section is used, the "ftraced" kernel thread is disabled.
This uses the current infrastructure to record the mcount call sites
as well as convert them to nops. The mcount function is kept as a stub
on boot up and not converted to the ftrace_record_ip function. We use the
ftrace_record_ip to only record from the table.
This patch does not handle modules. That comes with a later patch.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch creates a section in the kernel called "__mcount_loc".
This will hold a list of pointers to the mcount relocation for
each call site of mcount.
For example:
objdump -dr init/main.o
[...]
Disassembly of section .text:
0000000000000000 <do_one_initcall>:
0: 55 push %rbp
[...]
000000000000017b <init_post>:
17b: 55 push %rbp
17c: 48 89 e5 mov %rsp,%rbp
17f: 53 push %rbx
180: 48 83 ec 08 sub $0x8,%rsp
184: e8 00 00 00 00 callq 189 <init_post+0xe>
185: R_X86_64_PC32 mcount+0xfffffffffffffffc
[...]
We will add a section to point to each function call.
.section __mcount_loc,"a",@progbits
[...]
.quad .text + 0x185
[...]
The offset to of the mcount call site in init_post is an offset from
the start of the section, and not the start of the function init_post.
The mcount relocation is at the call site 0x185 from the start of the
.text section.
.text + 0x185 == init_post + 0xa
We need a way to add this __mcount_loc section in a way that we do not
lose the relocations after final link. The .text section here will
be attached to all other .text sections after final link and the
offsets will be meaningless. We need to keep track of where these
.text sections are.
To do this, we use the start of the first function in the section.
do_one_initcall. We can make a tmp.s file with this function as a reference
to the start of the .text section.
.section __mcount_loc,"a",@progbits
[...]
.quad do_one_initcall + 0x185
[...]
Then we can compile the tmp.s into a tmp.o
gcc -c tmp.s -o tmp.o
And link it into back into main.o.
ld -r main.o tmp.o -o tmp_main.o
mv tmp_main.o main.o
But we have a problem. What happens if the first function in a section
is not exported, and is a static function. The linker will not let
the tmp.o use it. This case exists in main.o as well.
Disassembly of section .init.text:
0000000000000000 <set_reset_devices>:
0: 55 push %rbp
1: 48 89 e5 mov %rsp,%rbp
4: e8 00 00 00 00 callq 9 <set_reset_devices+0x9>
5: R_X86_64_PC32 mcount+0xfffffffffffffffc
The first function in .init.text is a static function.
00000000000000a8 t __setup_set_reset_devices
000000000000105f t __setup_str_set_reset_devices
0000000000000000 t set_reset_devices
The lowercase 't' means that set_reset_devices is local and is not exported.
If we simply try to link the tmp.o with the set_reset_devices we end
up with two symbols: one local and one global.
.section __mcount_loc,"a",@progbits
.quad set_reset_devices + 0x10
00000000000000a8 t __setup_set_reset_devices
000000000000105f t __setup_str_set_reset_devices
0000000000000000 t set_reset_devices
U set_reset_devices
We still have an undefined reference to set_reset_devices, and if we try
to compile the kernel, we will end up with an undefined reference to
set_reset_devices, or even worst, it could be exported someplace else,
and then we will have a reference to the wrong location.
To handle this case, we make an intermediate step using objcopy.
We convert set_reset_devices into a global exported symbol before linking
it with tmp.o and set it back afterwards.
00000000000000a8 t __setup_set_reset_devices
000000000000105f t __setup_str_set_reset_devices
0000000000000000 T set_reset_devices
00000000000000a8 t __setup_set_reset_devices
000000000000105f t __setup_str_set_reset_devices
0000000000000000 T set_reset_devices
00000000000000a8 t __setup_set_reset_devices
000000000000105f t __setup_str_set_reset_devices
0000000000000000 t set_reset_devices
Now we have a section in main.o called __mcount_loc that we can place
somewhere in the kernel using vmlinux.ld.S and access it to convert
all these locations that call mcount into nops before starting SMP
and thus, eliminating the need to do this with kstop_machine.
Note, A well documented perl script (scripts/recordmcount.pl) is used
to do all this in one location.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
kprobes already has an extensive list of annotations for functions
that should not be instrumented. Add notrace annotations to these
functions as well.
This is particularly useful for functions called by the NMI path.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
do not expose users to CONFIG_TRACEPOINTS - tracers can select it
just fine.
update ftrace to select CONFIG_TRACEPOINTS.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Instrument the scheduler activity (sched_switch, migration, wakeups,
wait for a task, signal delivery) and process/thread
creation/destruction (fork, exit, kthread stop). Actually, kthread
creation is not instrumented in this patch because it is architecture
dependent. It allows to connect tracers such as ftrace which detects
scheduling latencies, good/bad scheduler decisions. Tools like LTTng can
export this scheduler information along with instrumentation of the rest
of the kernel activity to perform post-mortem analysis on the scheduler
activity.
About the performance impact of tracepoints (which is comparable to
markers), even without immediate values optimizations, tests done by
Hideo Aoki on ia64 show no regression. His test case was using hackbench
on a kernel where scheduler instrumentation (about 5 events in code
scheduler code) was added. See the "Tracepoints" patch header for
performance result detail.
Changelog :
- Change instrumentation location and parameter to match ftrace
instrumentation, previously done with kernel markers.
[ mingo@elte.hu: conflict resolutions ]
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: 'Peter Zijlstra' <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Implementation of kernel tracepoints. Inspired from the Linux Kernel
Markers. Allows complete typing verification by declaring both tracing
statement inline functions and probe registration/unregistration static
inline functions within the same macro "DEFINE_TRACE". No format string
is required. See the tracepoint Documentation and Samples patches for
usage examples.
Taken from the documentation patch :
"A tracepoint placed in code provides a hook to call a function (probe)
that you can provide at runtime. A tracepoint can be "on" (a probe is
connected to it) or "off" (no probe is attached). When a tracepoint is
"off" it has no effect, except for adding a tiny time penalty (checking
a condition for a branch) and space penalty (adding a few bytes for the
function call at the end of the instrumented function and adds a data
structure in a separate section). When a tracepoint is "on", the
function you provide is called each time the tracepoint is executed, in
the execution context of the caller. When the function provided ends its
execution, it returns to the caller (continuing from the tracepoint
site).
You can put tracepoints at important locations in the code. They are
lightweight hooks that can pass an arbitrary number of parameters, which
prototypes are described in a tracepoint declaration placed in a header
file."
Addition and removal of tracepoints is synchronized by RCU using the
scheduler (and preempt_disable) as guarantees to find a quiescent state
(this is really RCU "classic"). The update side uses rcu_barrier_sched()
with call_rcu_sched() and the read/execute side uses
"preempt_disable()/preempt_enable()".
We make sure the previous array containing probes, which has been
scheduled for deletion by the rcu callback, is indeed freed before we
proceed to the next update. It therefore limits the rate of modification
of a single tracepoint to one update per RCU period. The objective here
is to permit fast batch add/removal of probes on _different_
tracepoints.
Changelog :
- Use #name ":" #proto as string to identify the tracepoint in the
tracepoint table. This will make sure not type mismatch happens due to
connexion of a probe with the wrong type to a tracepoint declared with
the same name in a different header.
- Add tracepoint_entry_free_old.
- Change __TO_TRACE to get rid of the 'i' iterator.
Masami Hiramatsu <mhiramat@redhat.com> :
Tested on x86-64.
Performance impact of a tracepoint : same as markers, except that it
adds about 70 bytes of instructions in an unlikely branch of each
instrumented function (the for loop, the stack setup and the function
call). It currently adds a memory read, a test and a conditional branch
at the instrumentation site (in the hot path). Immediate values will
eventually change this into a load immediate, test and branch, which
removes the memory read which will make the i-cache impact smaller
(changing the memory read for a load immediate removes 3-4 bytes per
site on x86_32 (depending on mov prefixes), or 7-8 bytes on x86_64, it
also saves the d-cache hit).
About the performance impact of tracepoints (which is comparable to
markers), even without immediate values optimizations, tests done by
Hideo Aoki on ia64 show no regression. His test case was using hackbench
on a kernel where scheduler instrumentation (about 5 events in code
scheduler code) was added.
Quoting Hideo Aoki about Markers :
I evaluated overhead of kernel marker using linux-2.6-sched-fixes git
tree, which includes several markers for LTTng, using an ia64 server.
While the immediate trace mark feature isn't implemented on ia64, there
is no major performance regression. So, I think that we don't have any
issues to propose merging marker point patches into Linus's tree from
the viewpoint of performance impact.
I prepared two kernels to evaluate. The first one was compiled without
CONFIG_MARKERS. The second one was enabled CONFIG_MARKERS.
I downloaded the original hackbench from the following URL:
http://devresources.linux-foundation.org/craiger/hackbench/src/hackbench.c
I ran hackbench 5 times in each condition and calculated the average and
difference between the kernels.
The parameter of hackbench: every 50 from 50 to 800
The number of CPUs of the server: 2, 4, and 8
Below is the results. As you can see, major performance regression
wasn't found in any case. Even if number of processes increases,
differences between marker-enabled kernel and marker- disabled kernel
doesn't increase. Moreover, if number of CPUs increases, the differences
doesn't increase either.
Curiously, marker-enabled kernel is better than marker-disabled kernel
in more than half cases, although I guess it comes from the difference
of memory access pattern.
* 2 CPUs
Number of | without | with | diff | diff |
processes | Marker [Sec] | Marker [Sec] | [Sec] | [%] |
--------------------------------------------------------------
50 | 4.811 | 4.872 | +0.061 | +1.27 |
100 | 9.854 | 10.309 | +0.454 | +4.61 |
150 | 15.602 | 15.040 | -0.562 | -3.6 |
200 | 20.489 | 20.380 | -0.109 | -0.53 |
250 | 25.798 | 25.652 | -0.146 | -0.56 |
300 | 31.260 | 30.797 | -0.463 | -1.48 |
350 | 36.121 | 35.770 | -0.351 | -0.97 |
400 | 42.288 | 42.102 | -0.186 | -0.44 |
450 | 47.778 | 47.253 | -0.526 | -1.1 |
500 | 51.953 | 52.278 | +0.325 | +0.63 |
550 | 58.401 | 57.700 | -0.701 | -1.2 |
600 | 63.334 | 63.222 | -0.112 | -0.18 |
650 | 68.816 | 68.511 | -0.306 | -0.44 |
700 | 74.667 | 74.088 | -0.579 | -0.78 |
750 | 78.612 | 79.582 | +0.970 | +1.23 |
800 | 85.431 | 85.263 | -0.168 | -0.2 |
--------------------------------------------------------------
* 4 CPUs
Number of | without | with | diff | diff |
processes | Marker [Sec] | Marker [Sec] | [Sec] | [%] |
--------------------------------------------------------------
50 | 2.586 | 2.584 | -0.003 | -0.1 |
100 | 5.254 | 5.283 | +0.030 | +0.56 |
150 | 8.012 | 8.074 | +0.061 | +0.76 |
200 | 11.172 | 11.000 | -0.172 | -1.54 |
250 | 13.917 | 14.036 | +0.119 | +0.86 |
300 | 16.905 | 16.543 | -0.362 | -2.14 |
350 | 19.901 | 20.036 | +0.135 | +0.68 |
400 | 22.908 | 23.094 | +0.186 | +0.81 |
450 | 26.273 | 26.101 | -0.172 | -0.66 |
500 | 29.554 | 29.092 | -0.461 | -1.56 |
550 | 32.377 | 32.274 | -0.103 | -0.32 |
600 | 35.855 | 35.322 | -0.533 | -1.49 |
650 | 39.192 | 38.388 | -0.804 | -2.05 |
700 | 41.744 | 41.719 | -0.025 | -0.06 |
750 | 45.016 | 44.496 | -0.520 | -1.16 |
800 | 48.212 | 47.603 | -0.609 | -1.26 |
--------------------------------------------------------------
* 8 CPUs
Number of | without | with | diff | diff |
processes | Marker [Sec] | Marker [Sec] | [Sec] | [%] |
--------------------------------------------------------------
50 | 2.094 | 2.072 | -0.022 | -1.07 |
100 | 4.162 | 4.273 | +0.111 | +2.66 |
150 | 6.485 | 6.540 | +0.055 | +0.84 |
200 | 8.556 | 8.478 | -0.078 | -0.91 |
250 | 10.458 | 10.258 | -0.200 | -1.91 |
300 | 12.425 | 12.750 | +0.325 | +2.62 |
350 | 14.807 | 14.839 | +0.032 | +0.22 |
400 | 16.801 | 16.959 | +0.158 | +0.94 |
450 | 19.478 | 19.009 | -0.470 | -2.41 |
500 | 21.296 | 21.504 | +0.208 | +0.98 |
550 | 23.842 | 23.979 | +0.137 | +0.57 |
600 | 26.309 | 26.111 | -0.198 | -0.75 |
650 | 28.705 | 28.446 | -0.259 | -0.9 |
700 | 31.233 | 31.394 | +0.161 | +0.52 |
750 | 34.064 | 33.720 | -0.344 | -1.01 |
800 | 36.320 | 36.114 | -0.206 | -0.57 |
--------------------------------------------------------------
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: 'Peter Zijlstra' <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Various people outside the tty layer still stick their noses in behind the
scenes. We need to make sure they also obey the locking and referencing rules.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is pure tty code so put it in the tty layer where it can be with the
locking relevant material it uses
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce a kref to the tty structure and use it to protect the tty->signal
tty references. For now we don't introduce it for anything else.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-v28-for-linus-phase4-D' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (186 commits)
x86, debug: print more information about unknown CPUs
x86 setup: handle more than 8 CPU flag words
x86: cpuid, fix typo
x86: move transmeta cap read to early_init_transmeta()
x86: identify_cpu_without_cpuid v2
x86: extended "flags" to show virtualization HW feature in /proc/cpuinfo
x86: move VMX MSRs to msr-index.h
x86: centaur_64.c remove duplicated setting of CONSTANT_TSC
x86: intel.c put workaround for old cpus together
x86: let intel 64-bit use intel.c
x86: make intel_64.c the same as intel.c
x86: make intel.c have 64-bit support code
x86: little clean up of intel.c/intel_64.c
x86: make 64 bit to use amd.c
x86: make amd_64 have 32 bit code
x86: make amd.c have 64bit support code
x86: merge header in amd_64.c
x86: add srat_detect_node for amd64
x86: remove duplicated force_mwait
x86: cpu make amd.c more like amd_64.c v2
...
* 'x86-v28-for-linus-phase3-B' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (74 commits)
AMD IOMMU: use iommu_device_max_index, fix
AMD IOMMU: use iommu_device_max_index
x86: add PCI IDs for AMD Barcelona PCI devices
x86/iommu: use __GFP_ZERO instead of memset for GART
x86/iommu: convert GART need_flush to bool
x86/iommu: make GART driver checkpatch clean
x86 gart: remove unnecessary initialization
x86: restore old GART alloc_coherent behavior
revert "x86: make GART to respect device's dma_mask about virtual mappings"
x86: export pci-nommu's alloc_coherent
iommu: remove fullflush and nofullflush in IOMMU generic option
x86: remove set_bit_string()
iommu: export iommu_area_reserve helper function
AMD IOMMU: use coherent_dma_mask in alloc_coherent
add AMD IOMMU tree to MAINTAINERS file
AMD IOMMU: use cmd_buf_size when freeing the command buffer
AMD IOMMU: calculate IVHD size with a function
AMD IOMMU: remove unnecessary cast to u64 in the init code
AMD IOMMU: free domain bitmap with its allocation order
AMD IOMMU: simplify dma_mask_to_pages
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix BUG: using smp_processor_id() in preemptible code
[CPUFREQ] Don't export governors for default governor
[CPUFREQ][6/6] cpufreq: Add idle microaccounting in ondemand governor
[CPUFREQ][5/6] cpufreq: Changes to get_cpu_idle_time_us(), used by ondemand governor
[CPUFREQ][4/6] cpufreq_ondemand: Parameterize down differential
[CPUFREQ][3/6] cpufreq: get_cpu_idle_time() changes in ondemand for idle-microaccounting
[CPUFREQ][2/6] cpufreq: Change load calculation in ondemand for software coordination
[CPUFREQ][1/6] cpufreq: Add cpu number parameter to __cpufreq_driver_getavg()
[CPUFREQ] use deferrable delayed work init in conservative governor
[CPUFREQ] drivers/cpufreq/cpufreq.c: Adjust error handling code involving cpufreq_cpu_put
[CPUFREQ] add error handling for cpufreq_register_governor() error
[CPUFREQ] acpi-cpufreq: add error handling for cpufreq_register_driver() error
[CPUFREQ] Coding style fixes to arch/x86/kernel/cpu/cpufreq/powernow-k6.c
[CPUFREQ] Coding style fixes to arch/x86/kernel/cpu/cpufreq/elanfreq.c
* 'rcu-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (21 commits)
rcu: RCU-based detection of stalled CPUs for Classic RCU, fix
rcu: RCU-based detection of stalled CPUs for Classic RCU
rcu: add rcu_read_lock_sched() / rcu_read_unlock_sched()
rcu: fix sparse shadowed variable warning
doc/RCU: fix pseudocode in rcuref.txt
rcuclassic: fix compiler warning
rcu: use irq-safe locks
rcuclassic: fix compilation NG
rcu: fix locking cleanup fallout
rcu: remove redundant ACCESS_ONCE definition from rcupreempt.c
rcu: fix classic RCU locking cleanup lockdep problem
rcu: trace fix possible mem-leak
rcu: just rename call_rcu_bh instead of making it a macro
rcu: remove list_for_each_rcu()
rcu: fixes to include/linux/rcupreempt.h
rcu: classic RCU locking and memory-barrier cleanups
rcu: prevent console flood when one CPU sees another AWOL via RCU
rcu, debug: detect stalled grace periods, cleanups
rcu, debug: detect stalled grace periods
rcu classic: new algorithm for callbacks-processing(v2)
...
export get_cpu_idle_time_us() for it to be used in ondemand governor.
Last update time can be current time when the CPU is currently non-idle,
accounting for the busy time since last idle.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
add /proc/sys/kernel/sched_domain/cpu0/domain0/name, to make
it easier to see which specific scheduler domain remained at
that entry.
Since we process the scheduler domain tree and
simplify it, it's not always immediately clear during debugging
which domain came from where.
depends on CONFIG_SCHED_DEBUG=y.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While looking at the code I wondered why we always do:
sync && avg_overlap < migration_cost
Which is a bit odd, since the overlap test was meant to detect sync wakeups
so using it to specialize sync wakeups doesn't make much sense.
Hence change the code to do:
sync || avg_overlap < migration_cost
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The softlockup watchdog needs to be touched when resuming the from the
kgdb stopped state to avoid the printk that a CPU is stuck if the
debugger was active for longer than the softlockup threshold.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
css will be initialized by cgroup core.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While working on the new version of the code for SCHED_SPORADIC I
noticed something strange in the present throttling mechanism. More
specifically in the throttling timer handler in sched_rt.c
(do_sched_rt_period_timer()) and in rt_rq_enqueue().
The problem is that, when unthrottling a runqueue, rt_rq_enqueue() only
asks for rescheduling if the runqueue has a sched_entity associated to
it (i.e., rt_rq->rt_se != NULL).
Now, if the runqueue is the root rq (which has a rt_se = NULL)
rescheduling does not take place, and it is delayed to some undefined
instant in the future.
This imply some random bandwidth usage by the RT tasks under throttling.
For instance, setting rt_runtime_us/rt_period_us = 950ms/1000ms an RT
task will get less than 95%. In our tests we got something varying
between 70% to 95%.
Using smaller time values, e.g., 95ms/100ms, things are even worse, and
I can see values also going down to 20-25%!!
The tests we performed are simply running 'yes' as a SCHED_FIFO task,
and checking the CPU usage with top, but we can investigate thoroughly
if you think it is needed.
Things go much better, for us, with the attached patch... Don't know if
it is the best approach, but it solved the issue for us.
Signed-off-by: Dario Faggioli <raistlin@linux.it>
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: jiffies increment too fast.
Hugh Dickins noted that with NOHZ=n and HIGHRES=n jiffies get
incremented too fast. The reason is a wrong check in the broadcast
enter/exit code, which keeps the local apic timer in periodic mode
when the switch happens.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This fixes a warning on latest -tip:
kernel/cpuset.c: Dans la fonction «scan_for_empty_cpusets» :
kernel/cpuset.c:1932: attention : passing argument 1 of «list_add_tail» discards qualifiers from pointer target type
Actually the struct cpuset *root passed in parameter to scan_for_empty_cpusets
is not supposed to be const since an entry is added on the tail of its list.
Just correct the qualifier.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix the !CONFIG_RCU_CPU_STALL_DETECTOR path:
kernel/rcuclassic.c: In function '__rcu_pending':
kernel/rcuclassic.c:609: error: too few arguments to function 'check_cpu_stall'
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds stalled-CPU detection to Classic RCU. This capability
is enabled by a new config variable CONFIG_RCU_CPU_STALL_DETECTOR, which
defaults disabled.
This is a debugging feature to detect infinite loops in kernel code, not
something that non-kernel-hackers would be expected to care about.
This feature can detect looping CPUs in !PREEMPT builds and looping CPUs
with preemption disabled in PREEMPT builds. This is essentially a port of
this functionality from the treercu patch, replacing the stall debug patch
that is already in tip/core/rcu (commit 67182ae1c4).
The changes from the patch in tip/core/rcu include making the config
variable name match that in treercu, changing from seconds to jiffies to
avoid spurious warnings, and printing a boot message when this feature
is enabled.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Found by static checker (http://repo.or.cz/w/smatch.git).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
hrtimer: prevent migration of per CPU hrtimers
hrtimer: mark migration state
hrtimer: fix migration of CB_IRQSAFE_NO_SOFTIRQ hrtimers
hrtimer: migrate pending list on cpu offline
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This patch does following:
o Removes unused variable and argument "rq".
o Optimizes one of the "if" conditions in wake_affine() - i.e. if
"balanced" is true, we need not do rest of the calculations in the
condition.
o If this cpu is same as the previous cpu (on which woken up task
was running when it went to sleep), no need to call wake_affine at all.
Signed-off-by: Amit K Arora <aarora@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Steven Rostedt