When run test case:
mdadm -CR /dev/md1 -l 1 -n 4 /dev/sd[a-d] --assume-clean --bitmap=internal
mdadm -S /dev/md1
mdadm -A /dev/md1 /dev/sd[b-c] --run --force
mdadm --zero /dev/sda
mdadm /dev/md1 -a /dev/sda
echo offline > /sys/block/sdc/device/state
echo offline > /sys/block/sdb/device/state
sleep 5
mdadm -S /dev/md1
echo running > /sys/block/sdb/device/state
echo running > /sys/block/sdc/device/state
mdadm -A /dev/md1 /dev/sd[a-c] --run --force
mdadm run fail with kernel message as follow:
[ 172.986064] md: kicking non-fresh sdb from array!
[ 173.004210] md: kicking non-fresh sdc from array!
[ 173.022383] md/raid1:md1: active with 0 out of 4 mirrors
[ 173.022406] md1: failed to create bitmap (-5)
In fact, when active disk in raid1 array less than one, we
need to return fail in raid1_run().
Reviewed-by: NeilBrown <neilb@suse.de>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
When the 'last' device in a RAID1 or RAID10 reports an error,
we do not mark it as failed. This would serve little purpose
as there is no risk of losing data beyond that which is obviously
lost (as there is with RAID5), and there could be other sectors
on the device which are readable, and only readable from this device.
This in general this maximises access to data.
However the current implementation also stops an admin from removing
the last device by direct action. This is rarely useful, but in many
case is not harmful and can make automation easier by removing special
cases.
Also, if an attempt to write metadata fails the device must be marked
as faulty, else an infinite loop will result, attempting to update
the metadata on all non-faulty devices.
So add 'fail_last_dev' member to 'struct mddev', then we can bypasses
the 'last disk' checks for RAID1 and RAID10, and control the behavior
per array by change sysfs node.
Signed-off-by: NeilBrown <neilb@suse.de>
[add sysfs node for fail_last_dev by Guoqing]
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
When write bio return error, it would be added to conf->retry_list
and wait for raid1d thread to retry write and acknowledge badblocks.
In narrow_write_error(), the error bio will be split in the unit of
badblock shift (such as one sector) and raid1d thread issues them
one by one. Until all of the splited bio has finished, raid1d thread
can go on processing other things, which is time consuming.
But, there is a scene for error handling that is not necessary.
When the device has been set faulty, flush_bio_list() may end
bios in pending_bio_list with error status. Since these bios
has not been issued to the device actually, error handlding to
retry write and acknowledge badblocks make no sense.
Even without that scene, when the device is faulty, badblocks info
can not be written out to the device. Thus, we also no need to
handle the error IO.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Using a sector_t as the return value is misleading, because
raise_barrier() only return 0 or -EINTR.
Also add comments for the return values of raise_barrier().
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
The WARN_ON() macro doesn't take an error message, it just takes a
condition. I've changed this to use WARN(1, "...") instead.
Fixes: 3e148a3209 ("md/raid1: fix potential data inconsistency issue with write behind device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
For write-behind mode, we think write IO is complete once it has
reached all the non-writemostly devices. It works fine for single
queue devices.
But for multiqueue device, if there are lots of IOs come from upper
layer, then the write-behind device could issue those IOs to different
queues, depends on the each queue's delay, so there is no guarantee
that those IOs can arrive in order.
To address the issue, we need to check the collision among write
behind IOs, we can only continue without collision, otherwise wait
for the completion of previous collisioned IO.
And WBCollision is introduced for multiqueue device which is worked
under write-behind mode.
But this patch doesn't handle below cases which could have the data
inconsistency issue as well, these cases will be handled in later
patches.
1. modify max_write_behind by write backlog node.
2. add or remove array's bitmap dynamically.
3. the change of member disk.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Avoiding duplicated code, since they just execute a kfree.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch get rid of extra blank line and space, and
add necessary space for code.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
These definitions are being moved to raid1-10.c.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version you should have received a copy of the gnu general
public license for example usr src linux copying if not write to the
free software foundation inc 675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 20 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170858.552543146@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only have two callers that need the integer loop iterator, and they
can easily maintain it themselves.
Suggested-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: David Sterba <dsterba@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Coly Li <colyli@suse.de>
Reviewed-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=VBaU
-----END PGP SIGNATURE-----
Merge tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"Not a huge amount of changes in this round, the biggest one is that we
finally have Mings multi-page bvec support merged. Apart from that,
this pull request contains:
- Small series that avoids quiescing the queue for sysfs changes that
match what we currently have (Aleksei)
- Series of bcache fixes (via Coly)
- Series of lightnvm fixes (via Mathias)
- NVMe pull request from Christoph. Nothing major, just SPDX/license
cleanups, RR mp policy (Hannes), and little fixes (Bart,
Chaitanya).
- BFQ series (Paolo)
- Save blk-mq cpu -> hw queue mapping, removing a pointer indirection
for the fast path (Jianchao)
- fops->iopoll() added for async IO polling, this is a feature that
the upcoming io_uring interface will use (Christoph, me)
- Partition scan loop fixes (Dongli)
- mtip32xx conversion from managed resource API (Christoph)
- cdrom registration race fix (Guenter)
- MD pull from Song, two minor fixes.
- Various documentation fixes (Marcos)
- Multi-page bvec feature. This brings a lot of nice improvements
with it, like more efficient splitting, larger IOs can be supported
without growing the bvec table size, and so on. (Ming)
- Various little fixes to core and drivers"
* tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block: (117 commits)
block: fix updating bio's front segment size
block: Replace function name in string with __func__
nbd: propagate genlmsg_reply return code
floppy: remove set but not used variable 'q'
null_blk: fix checking for REQ_FUA
block: fix NULL pointer dereference in register_disk
fs: fix guard_bio_eod to check for real EOD errors
blk-mq: use HCTX_TYPE_DEFAULT but not 0 to index blk_mq_tag_set->map
block: optimize bvec iteration in bvec_iter_advance
block: introduce mp_bvec_for_each_page() for iterating over page
block: optimize blk_bio_segment_split for single-page bvec
block: optimize __blk_segment_map_sg() for single-page bvec
block: introduce bvec_nth_page()
iomap: wire up the iopoll method
block: add bio_set_polled() helper
block: wire up block device iopoll method
fs: add an iopoll method to struct file_operations
loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part()
loop: do not print warn message if partition scan is successful
block: bounce: make sure that bvec table is updated
...
This patch introduces one extra iterator variable to bio_for_each_segment_all(),
then we can allow bio_for_each_segment_all() to iterate over multi-page bvec.
Given it is just one mechannical & simple change on all bio_for_each_segment_all()
users, this patch does tree-wide change in one single patch, so that we can
avoid to use a temporary helper for this conversion.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
sync_request_write no longer submits writes to a Faulty device. This has
the unfortunate side effect that bitmap bits can be incorrectly cleared
if a recovery is interrupted (previously, end_sync_write would have
prevented this). This means the next recovery may not copy everything
it should, potentially corrupting data.
Add a function for doing the proper md_bitmap_end_sync, called from
end_sync_write and the Faulty case in sync_request_write.
backport note to 4.14: s/md_bitmap_end_sync/bitmap_end_sync
Cc: stable@vger.kernel.org 4.14+
Fixes: 0c9d5b127f ("md/raid1: avoid reusing a resync bio after error handling.")
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Tested-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Commit d595567dc4 (MD: fix invalid stored role for a disk) broke linear
hotadd. Let's only fix the role for disks in raid1/10.
Based on Guoqing's original patch.
Reported-by: kernel test robot <rong.a.chen@intel.com>
Cc: Gioh Kim <gi-oh.kim@profitbricks.com>
Cc: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Pull input updates from Dmitry Torokhov:
- a new driver for Rohm BU21029 touch controller
- new bitmap APIs: bitmap_alloc, bitmap_zalloc and bitmap_free
- updates to Atmel, eeti. pxrc and iforce drivers
- assorted driver cleanups and fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
MAINTAINERS: Add PhoenixRC Flight Controller Adapter
Input: do not use WARN() in input_alloc_absinfo()
Input: mark expected switch fall-throughs
Input: raydium_i2c_ts - use true and false for boolean values
Input: evdev - switch to bitmap API
Input: gpio-keys - switch to bitmap_zalloc()
Input: elan_i2c_smbus - cast sizeof to int for comparison
bitmap: Add bitmap_alloc(), bitmap_zalloc() and bitmap_free()
md: Avoid namespace collision with bitmap API
dm: Avoid namespace collision with bitmap API
Input: pm8941-pwrkey - add resin entry
Input: pm8941-pwrkey - abstract register offsets and event code
Input: iforce - reorganize joystick configuration lists
Input: atmel_mxt_ts - move completion to after config crc is updated
Input: atmel_mxt_ts - don't report zero pressure from T9
Input: atmel_mxt_ts - zero terminate config firmware file
Input: atmel_mxt_ts - refactor config update code to add context struct
Input: atmel_mxt_ts - config CRC may start at T71
Input: atmel_mxt_ts - remove unnecessary debug on ENOMEM
Input: atmel_mxt_ts - remove duplicate setup of ABS_MT_PRESSURE
...
bitmap API (include/linux/bitmap.h) has 'bitmap' prefix for its methods.
On the other hand MD bitmap API is special case.
Adding 'md' prefix to it to avoid name space collision.
No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Shaohua Li <shli@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull MD updates from Shaohua Li:
"A few fixes of MD for this merge window. Mostly bug fixes:
- raid5 stripe batch fix from Amy
- Read error handling for raid1 FailFast device from Gioh
- raid10 recovery NULL pointer dereference fix from Guoqing
- Support write hint for raid5 stripe cache from Mariusz
- Fixes for device hot add/remove from Neil and Yufen
- Improve flush bio scalability from Xiao"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
MD: fix lock contention for flush bios
md/raid5: Assigning NULL to sh->batch_head before testing bit R5_Overlap of a stripe
md/raid1: add error handling of read error from FailFast device
md: fix NULL dereference of mddev->pers in remove_and_add_spares()
raid5: copy write hint from origin bio to stripe
md: fix two problems with setting the "re-add" device state.
raid10: check bio in r10buf_pool_free to void NULL pointer dereference
md: fix an error code format and remove unsed bio_sector
Current handle_read_error() function calls fix_read_error()
only if md device is RW and rdev does not include FailFast flag.
It does not handle a read error from a RW device including
FailFast flag.
I am not sure it is intended. But I found that write IO error
sets rdev faulty. The md module should handle the read IO error and
write IO error equally. So I think read IO error should set rdev faulty.
Signed-off-by: Gioh Kim <gi-oh.kim@profitbricks.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We met a sync thread stuck as follows:
raid1_sync_request+0x2c9/0xb50
md_do_sync+0x983/0xfa0
md_thread+0x11c/0x160
kthread+0x111/0x130
ret_from_fork+0x35/0x40
0xffffffffffffffff
At the same time, there is a stuck mdadm thread (mdadm --manage
/dev/md2 --add /dev/sda). It is trying to stop the sync thread:
kthread_stop+0x42/0xf0
md_unregister_thread+0x3a/0x70
md_reap_sync_thread+0x15/0x160
action_store+0x142/0x2a0
md_attr_store+0x6c/0xb0
kernfs_fop_write+0x102/0x180
__vfs_write+0x33/0x170
vfs_write+0xad/0x1a0
SyS_write+0x52/0xc0
do_syscall_64+0x6e/0x190
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
Debug tools show that the sync thread is waiting in raise_barrier(),
until raid1d() end all normal IO bios into bio_end_io_list(introduced
in commit 55ce74d4bf). But, raid1d() cannot end these bios if
MD_CHANGE_PENDING bit is set. It needs to get mddev->reconfig_mutex lock
and then clear the bit in md_check_recovery().
However, the lock is holding by mdadm in action_store().
Thus, there is a loop:
mdadm waiting for sync thread to stop, sync thread waiting for
raid1d() to end bios, raid1d() waiting for mdadm to release
mddev->reconfig_mutex lock and then it can end bios.
Fix this by checking MD_RECOVERY_INTR while waiting in raise_barrier(),
so that sync thread can exit while mdadm is stoping the sync thread.
Fixes: 55ce74d4bf ("md/raid1: ensure device failure recorded before write request returns.")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Shaohua Li <shli@fb.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RVhK
-----END PGP SIGNATURE-----
Merge tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"It's a pretty quiet round this time, which is nice. This contains:
- series from Bart, cleaning up the way we set/test/clear atomic
queue flags.
- series from Bart, fixing races between gendisk and queue
registration and removal.
- set of bcache fixes and improvements from various folks, by way of
Michael Lyle.
- set of lightnvm updates from Matias, most of it being the 1.2 to
2.0 transition.
- removal of unused DIO flags from Nikolay.
- blk-mq/sbitmap memory ordering fixes from Omar.
- divide-by-zero fix for BFQ from Paolo.
- minor documentation patches from Randy.
- timeout fix from Tejun.
- Alpha "can't write a char atomically" fix from Mikulas.
- set of NVMe fixes by way of Keith.
- bsg and bsg-lib improvements from Christoph.
- a few sed-opal fixes from Jonas.
- cdrom check-disk-change deadlock fix from Maurizio.
- various little fixes, comment fixes, etc from various folks"
* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
blk-mq: Directly schedule q->timeout_work when aborting a request
blktrace: fix comment in blktrace_api.h
lightnvm: remove function name in strings
lightnvm: pblk: remove some unnecessary NULL checks
lightnvm: pblk: don't recover unwritten lines
lightnvm: pblk: implement 2.0 support
lightnvm: pblk: implement get log report chunk
lightnvm: pblk: rename ppaf* to addrf*
lightnvm: pblk: check for supported version
lightnvm: implement get log report chunk helpers
lightnvm: make address conversions depend on generic device
lightnvm: add support for 2.0 address format
lightnvm: normalize geometry nomenclature
lightnvm: complete geo structure with maxoc*
lightnvm: add shorten OCSSD version in geo
lightnvm: add minor version to generic geometry
lightnvm: simplify geometry structure
lightnvm: pblk: refactor init/exit sequences
lightnvm: Avoid validation of default op value
lightnvm: centralize permission check for lightnvm ioctl
...
This patch has been generated as follows:
for verb in set_unlocked clear_unlocked set clear; do
replace-in-files queue_flag_${verb} blk_queue_flag_${verb%_unlocked} \
$(git grep -lw queue_flag_${verb} drivers block/bsg*)
done
Except for protecting all queue flag changes with the queue lock
this patch does not change any functionality.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The trailing semicolon is an empty statement that does no operation.
Removing it since it doesn't do anything.
Signed-off-by: Luis de Bethencourt <luisbg@kernel.org>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
If you prepare_to_wait() after a previous prepare_to_wait(),
but before calling schedule(), you get warning:
do not call blocking ops when !TASK_RUNNING; state=2
This is appropriate as it is often a bug. The event that the
first prepare_to_wait() expects might wake up the schedule following
the second prepare_to_wait(), which could be confusing.
However if both prepare_to_wait()s are part of simple wait_event()
loops, and if the inner one is rarely called, then there is
no problem. The inner loop is too simple to get confused by
a stray wakeup, and the outer loop won't spin unduly because the
inner doesnt affect it often.
This pattern occurs in both raid1.c and raid10.c in the use of
flush_pending_writes().
The warning can be silenced by setting current->state to TASK_RUNNING.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
There are some lines could be removed due to recent
change for raid1 such as commit 3956df15d634 ("md:
move suspend_hi/lo handling into core md code").
Also, seems some comments are put to wrong place,
move them before wait_barrier.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If freeze_array is attempted in the middle of close_sync/
wait_all_barriers, deadlock can occur.
freeze_array will wait for nr_pending and nr_queued to line up.
wait_all_barriers increments nr_pending for each barrier bucket, one
at a time, but doesn't actually issue IO that could be counted in
nr_queued. So freeze_array is blocked until wait_all_barriers
completes and allow_all_barriers runs. At the same time, when
_wait_barrier sees array_frozen == 1, it stops and waits for
freeze_array to complete.
Prevent the deadlock by making close_sync call _wait_barrier and
_allow_barrier for one bucket at a time, instead of deferring the
_allow_barrier calls until after all _wait_barriers are complete.
Signed-off-by: Nate Dailey <nate.dailey@stratus.com>
Fix: fd76863e37fe(RAID1: a new I/O barrier implementation to remove resync window)
Reviewed-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org (v4.11)
Signed-off-by: Shaohua Li <shli@fb.com>
Hi - I submit this patch for the next merge window:
Some times ago, I made a patch f9c79bc05a that blocks signals around the
schedule() calls in MD. The MD subsystem needs to do an uninterruptible
sleep that is not accounted in load average - so we block signals and use
interruptible sleep.
The kernel has a special TASK_IDLE state for this purpose, so we can use
it instead of blocking signals. This patch doesn't fix any bug, it just
makes the code simpler.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The '2' argument means "wake up anything that is waiting".
This is an inelegant part of the design and was added
to help support management of suspend_lo/suspend_hi setting.
Now that suspend_lo/hi is managed in mddev_suspend/resume,
that need is gone.
These is still a couple of places where we call 'quiesce'
with an argument of '2', but they can safely be changed to
call ->quiesce(.., 1); ->quiesce(.., 0) which
achieve the same result at the small cost of pausing IO
briefly.
This removes a small "optimization" from suspend_{hi,lo}_store,
but it isn't clear that optimization served a useful purpose.
The code now is a lot clearer.
Suggested-by: Shaohua Li <shli@kernel.org>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
responding to ->suspend_lo and ->suspend_hi is similar
to responding to ->suspended. It is best to wait in
the common core code without incrementing ->active_io.
This allows mddev_suspend()/mddev_resume() to work while
requests are waiting for suspend_lo/hi to change.
This is will be important after a subsequent patch
which uses mddev_suspend() to synchronize updating for
suspend_lo/hi.
So move the code for testing suspend_lo/hi out of raid1.c
and raid5.c, and place it in md.c
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Motivated by the desire to illiminate the imprecise nature of
DM-specific patches being unnecessarily sent to both the MD maintainer
and mailing-list. Which is born out of the fact that DM files also
reside in drivers/md/
Now all MD-specific files in drivers/md/ start with either "raid" or
"md-" and the MAINTAINERS file has been updated accordingly.
Shaohua: don't change module name
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The check used here is to avoid conflict between write and
resync, however we used the wrong logic, it should be the
inverse of the checking inside "if".
Fixes: 589a1c4 ("Suspend writes in RAID1 if within range")
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Pull MD updates from Shaohua Li:
"This update mainly fixes bugs:
- Make raid5 ppl support several ppl from Pawel
- Several raid5-cache bug fixes from Song
- Bitmap fixes from Neil and Me
- One raid1/10 regression fix since 4.12 from Me
- Other small fixes and cleanup"
* tag 'md/4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/bitmap: disable bitmap_resize for file-backed bitmaps.
raid5-ppl: Recovery support for multiple partial parity logs
md: Runtime support for multiple ppls
md/raid0: attach correct cgroup info in bio
lib/raid6: align AVX512 constants to 512 bits, not bytes
raid5: remove raid5_build_block
md/r5cache: call mddev_lock/unlock() in r5c_journal_mode_show
md: replace seq_release_private with seq_release
md: notify about new spare disk in the container
md/raid1/10: reset bio allocated from mempool
md/raid5: release/flush io in raid5_do_work()
md/bitmap: copy correct data for bitmap super
Increase PPL area to 1MB and use it as circular buffer to store PPL. The
entry with highest generation number is the latest one. If PPL to be
written is larger then space left in a buffer, rewind the buffer to the
start (don't wrap it).
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Data allocated from mempool doesn't always get initialized, this happens when
the data is reused instead of fresh allocation. In the raid1/10 case, we must
reinitialize the bios.
Reported-by: Jonathan G. Underwood <jonathan.underwood@gmail.com>
Fixes: f0250618361d(md: raid10: don't use bio's vec table to manage resync pages)
Fixes: 98d30c5812c3(md: raid1: don't use bio's vec table to manage resync pages)
Cc: stable@vger.kernel.org (4.12+)
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
This way we don't need a block_device structure to submit I/O. The
block_device has different life time rules from the gendisk and
request_queue and is usually only available when the block device node
is open. Other callers need to explicitly create one (e.g. the lightnvm
passthrough code, or the new nvme multipathing code).
For the actual I/O path all that we need is the gendisk, which exists
once per block device. But given that the block layer also does
partition remapping we additionally need a partition index, which is
used for said remapping in generic_make_request.
Note that all the block drivers generally want request_queue or
sometimes the gendisk, so this removes a layer of indirection all
over the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since bio_io_error sets bi_status to BLK_STS_IOERR,
and calls bio_endio, so we can use it directly.
And as mentioned by Shaohua, there are also two
places in raid5.c can use bio_io_error either.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
After bio is submitted, we should not clone it as its bi_iter might be
invalid by driver. This is the case of behind_master_bio. In certain
situration, we could dispatch behind_master_bio immediately for the
first disk and then clone it for other disks.
https://bugzilla.kernel.org/show_bug.cgi?id=196383
Reported-and-tested-by: Markus <m4rkusxxl@web.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Fix: 841c1316c7da(md: raid1: improve write behind)
Cc: stable@vger.kernel.org (4.12+)
Signed-off-by: Shaohua Li <shli@fb.com>
No function change, just move 'struct resync_pages' and related
helpers into raid1-10.c
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We will support multipage bvec soon, so initialize bvec
table using the standardy way instead of writing the
talbe directly. Otherwise it won't work any more once
multipage bvec is enabled.
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
bio_add_page() won't fail for resync bio, and the page index for each
bio is same, so remove it.
More importantly the 'idx' of 'struct resync_pages' is initialized in
mempool allocator function, the current way is wrong since mempool is
only responsible for allocation, we can't use that for initialization.
Suggested-by: NeilBrown <neilb@suse.com>
Reported-by: NeilBrown <neilb@suse.com>
Reported-and-tested-by: Patrick <dto@gmx.net>
Fixes: f0250618361d(md: raid10: don't use bio's vec table to manage resync pages)
Fixes: 98d30c5812c3(md: raid1: don't use bio's vec table to manage resync pages)
Cc: stable@vger.kernel.org (4.12+)
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Pull MD update from Shaohua Li:
- fixed deadlock in MD suspend and a potential bug in bio allocation
(Neil Brown)
- fixed signal issue (Mikulas Patocka)
- fixed typo in FailFast test (Guoqing Jiang)
- other trival fixes
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
MD: fix sleep in atomic
MD: fix a null dereference
md: use a separate bio_set for synchronous IO.
md: change the initialization value for a spare device spot to MD_DISK_ROLE_SPARE
md/raid1: remove unused bio in sync_request_write
md/raid10: fix FailFast test for wrong device
md: don't use flush_signals in userspace processes
md: fix deadlock between mddev_suspend() and md_write_start()
Yufen Yu