In rtnl_net_notifyid(), we certainly can't pass a null GFP flag to
rtnl_notify(). A GFP_KERNEL flag would be fine in most circumstances,
but there are a few paths calling rtnl_net_notifyid() from atomic
context or from RCU critical sections. The later also precludes the use
of gfp_any() as it wouldn't detect the RCU case. Also, the nlmsg_new()
call is wrong too, as it uses GFP_KERNEL unconditionally.
Therefore, we need to pass the GFP flags as parameter and propagate it
through function calls until the proper flags can be determined.
In most cases, GFP_KERNEL is fine. The exceptions are:
* openvswitch: ovs_vport_cmd_get() and ovs_vport_cmd_dump()
indirectly call rtnl_net_notifyid() from RCU critical section,
* rtnetlink: rtmsg_ifinfo_build_skb() already receives GFP flags as
parameter.
Also, in ovs_vport_cmd_build_info(), let's change the GFP flags used
by nlmsg_new(). The function is allowed to sleep, so better make the
flags consistent with the ones used in the following
ovs_vport_cmd_fill_info() call.
Found by code inspection.
Fixes: 9a9634545c ("netns: notify netns id events")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating of an SMC-R connection with vlan-id fails, because
smc_listen_work() determines the vlan_id of the connection,
saves it in struct smc_init_info ini, but clears the ini area
again if SMC-D is not applicable.
This patch just resets the ISM device before investigating
SMC-R availability.
Fixes: bc36d2fc93 ("net/smc: consolidate function parameters")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SMC sockets forced to fallback to TCP, the file is propagated
from the outer SMC to the internal TCP socket. When closing the SMC
socket, the internal TCP socket file pointer must be restored to the
original NULL value, otherwise memory leaks may show up (found with
CONFIG_DEBUG_KMEMLEAK).
The internal TCP socket is released in smc_clcsock_release(), which
calls __sock_release() function in net/socket.c. This calls the
needed iput(SOCK_INODE(sock)) only, if the file pointer has been reset
to the original NULL-value.
Fixes: 07603b2308 ("net/smc: propagate file from SMC to TCP socket")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is networking hardware that isn't based on Ethernet for layers 1 and 2.
For example CAN.
CAN is a multi-master serial bus standard for connecting Electronic Control
Units [ECUs] also known as nodes. A frame on the CAN bus carries up to 8 bytes
of payload. Frame corruption is detected by a CRC. However frame loss due to
corruption is possible, but a quite unusual phenomenon.
While fq_codel works great for TCP/IP, it doesn't for CAN. There are a lot of
legacy protocols on top of CAN, which are not build with flow control or high
CAN frame drop rates in mind.
When using fq_codel, as soon as the queue reaches a certain delay based length,
skbs from the head of the queue are silently dropped. Silently meaning that the
user space using a send() or similar syscall doesn't get an error. However
TCP's flow control algorithm will detect dropped packages and adjust the
bandwidth accordingly.
When using fq_codel and sending raw frames over CAN, which is the common use
case, the user space thinks the package has been sent without problems, because
send() returned without an error. pfifo_fast will drop skbs, if the queue
length exceeds the maximum. But with this scheduler the skbs at the tail are
dropped, an error (-ENOBUFS) is propagated to user space. So that the user
space can slow down the package generation.
On distributions, where fq_codel is made default via CONFIG_DEFAULT_NET_SCH
during compile time, or set default during runtime with sysctl
net.core.default_qdisc (see [1]), we get a bad user experience. In my test case
with pfifo_fast, I can transfer thousands of million CAN frames without a frame
drop. On the other hand with fq_codel there is more then one lost CAN frame per
thousand frames.
As pointed out fq_codel is not suited for CAN hardware, so this patch changes
attach_one_default_qdisc() to use pfifo_fast for "ARPHRD_CAN" network devices.
During transition of a netdev from down to up state the default queuing
discipline is attached by attach_default_qdiscs() with the help of
attach_one_default_qdisc(). This patch modifies attach_one_default_qdisc() to
attach the pfifo_fast (pfifo_fast_ops) if the network device type is
"ARPHRD_CAN".
[1] https://github.com/systemd/systemd/issues/9194
Signed-off-by: Vincent Prince <vincent.prince.fr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes variables and callback these are related to the nested
device structure.
devices that can be nested have their own nest_level variable that
represents the depth of nested devices.
In the previous patch, new {lower/upper}_level variables are added and
they replace old private nest_level variable.
So, this patch removes all 'nest_level' variables.
In order to avoid lockdep warning, ->ndo_get_lock_subclass() was added
to get lockdep subclass value, which is actually lower nested depth value.
But now, they use the dynamic lockdep key to avoid lockdep warning instead
of the subclass.
So, this patch removes ->ndo_get_lock_subclass() callback.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to link an adjacent node, netdev_upper_dev_link() is used
and in order to unlink an adjacent node, netdev_upper_dev_unlink() is used.
unlink operation does not fail, but link operation can fail.
In order to exchange adjacent nodes, we should unlink an old adjacent
node first. then, link a new adjacent node.
If link operation is failed, we should link an old adjacent node again.
But this link operation can fail too.
It eventually breaks the adjacent link relationship.
This patch adds an ignore flag into the netdev_adjacent structure.
If this flag is set, netdev_upper_dev_link() ignores an old adjacent
node for a moment.
This patch also adds new functions for other modules.
netdev_adjacent_change_prepare()
netdev_adjacent_change_commit()
netdev_adjacent_change_abort()
netdev_adjacent_change_prepare() inserts new device into adjacent list
but new device is not allowed to use immediately.
If netdev_adjacent_change_prepare() fails, it internally rollbacks
adjacent list so that we don't need any other action.
netdev_adjacent_change_commit() deletes old device in the adjacent list
and allows new device to use.
netdev_adjacent_change_abort() rollbacks adjacent list.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some interface types could be nested.
(VLAN, BONDING, TEAM, MACSEC, MACVLAN, IPVLAN, VIRT_WIFI, VXLAN, etc..)
These interface types should set lockdep class because, without lockdep
class key, lockdep always warn about unexisting circular locking.
In the current code, these interfaces have their own lockdep class keys and
these manage itself. So that there are so many duplicate code around the
/driver/net and /net/.
This patch adds new generic lockdep keys and some helper functions for it.
This patch does below changes.
a) Add lockdep class keys in struct net_device
- qdisc_running, xmit, addr_list, qdisc_busylock
- these keys are used as dynamic lockdep key.
b) When net_device is being allocated, lockdep keys are registered.
- alloc_netdev_mqs()
c) When net_device is being free'd llockdep keys are unregistered.
- free_netdev()
d) Add generic lockdep key helper function
- netdev_register_lockdep_key()
- netdev_unregister_lockdep_key()
- netdev_update_lockdep_key()
e) Remove unnecessary generic lockdep macro and functions
f) Remove unnecessary lockdep code of each interfaces.
After this patch, each interface modules don't need to maintain
their lockdep keys.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code doesn't limit the number of nested devices.
Nested devices would be handled recursively and this needs huge stack
memory. So, unlimited nested devices could make stack overflow.
This patch adds upper_level and lower_level, they are common variables
and represent maximum lower/upper depth.
When upper/lower device is attached or dettached,
{lower/upper}_level are updated. and if maximum depth is bigger than 8,
attach routine fails and returns -EMLINK.
In addition, this patch converts recursive routine of
netdev_walk_all_{lower/upper} to iterator routine.
Test commands:
ip link add dummy0 type dummy
ip link add link dummy0 name vlan1 type vlan id 1
ip link set vlan1 up
for i in {2..55}
do
let A=$i-1
ip link add vlan$i link vlan$A type vlan id $i
done
ip link del dummy0
Splat looks like:
[ 155.513226][ T908] BUG: KASAN: use-after-free in __unwind_start+0x71/0x850
[ 155.514162][ T908] Write of size 88 at addr ffff8880608a6cc0 by task ip/908
[ 155.515048][ T908]
[ 155.515333][ T908] CPU: 0 PID: 908 Comm: ip Not tainted 5.4.0-rc3+ #96
[ 155.516147][ T908] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 155.517233][ T908] Call Trace:
[ 155.517627][ T908]
[ 155.517918][ T908] Allocated by task 0:
[ 155.518412][ T908] (stack is not available)
[ 155.518955][ T908]
[ 155.519228][ T908] Freed by task 0:
[ 155.519885][ T908] (stack is not available)
[ 155.520452][ T908]
[ 155.520729][ T908] The buggy address belongs to the object at ffff8880608a6ac0
[ 155.520729][ T908] which belongs to the cache names_cache of size 4096
[ 155.522387][ T908] The buggy address is located 512 bytes inside of
[ 155.522387][ T908] 4096-byte region [ffff8880608a6ac0, ffff8880608a7ac0)
[ 155.523920][ T908] The buggy address belongs to the page:
[ 155.524552][ T908] page:ffffea0001822800 refcount:1 mapcount:0 mapping:ffff88806c657cc0 index:0x0 compound_mapcount:0
[ 155.525836][ T908] flags: 0x100000000010200(slab|head)
[ 155.526445][ T908] raw: 0100000000010200 ffffea0001813808 ffffea0001a26c08 ffff88806c657cc0
[ 155.527424][ T908] raw: 0000000000000000 0000000000070007 00000001ffffffff 0000000000000000
[ 155.528429][ T908] page dumped because: kasan: bad access detected
[ 155.529158][ T908]
[ 155.529410][ T908] Memory state around the buggy address:
[ 155.530060][ T908] ffff8880608a6b80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 155.530971][ T908] ffff8880608a6c00: fb fb fb fb fb f1 f1 f1 f1 00 f2 f2 f2 f3 f3 f3
[ 155.531889][ T908] >ffff8880608a6c80: f3 fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 155.532806][ T908] ^
[ 155.533509][ T908] ffff8880608a6d00: fb fb fb fb fb fb fb fb fb f1 f1 f1 f1 00 00 00
[ 155.534436][ T908] ffff8880608a6d80: f2 f3 f3 f3 f3 fb fb fb 00 00 00 00 00 00 00 00
[ ... ]
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP IPv6 packets auto flowlabels are using a 32bit secret
(static u32 hashrnd in net/core/flow_dissector.c) and
apply jhash() over fields known by the receivers.
Attackers can easily infer the 32bit secret and use this information
to identify a device and/or user, since this 32bit secret is only
set at boot time.
Really, using jhash() to generate cookies sent on the wire
is a serious security concern.
Trying to change the rol32(hash, 16) in ip6_make_flowlabel() would be
a dead end. Trying to periodically change the secret (like in sch_sfq.c)
could change paths taken in the network for long lived flows.
Let's switch to siphash, as we did in commit df453700e8
("inet: switch IP ID generator to siphash")
Using a cryptographically strong pseudo random function will solve this
privacy issue and more generally remove other weak points in the stack.
Packet schedulers using skb_get_hash_perturb() benefit from this change.
Fixes: b56774163f ("ipv6: Enable auto flow labels by default")
Fixes: 42240901f7 ("ipv6: Implement different admin modes for automatic flow labels")
Fixes: 67800f9b1f ("ipv6: Call skb_get_hash_flowi6 to get skb->hash in ip6_make_flowlabel")
Fixes: cb1ce2ef38 ("ipv6: Implement automatic flow label generation on transmit")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Berger <jonathann1@walla.com>
Reported-by: Amit Klein <aksecurity@gmail.com>
Reported-by: Benny Pinkas <benny@pinkas.net>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include <net/addrconf.h> for the missing declarations of
various functions. Fixes the following sparse warnings:
net/ipv6/addrconf_core.c:94:5: warning: symbol 'register_inet6addr_notifier' was not declared. Should it be static?
net/ipv6/addrconf_core.c💯5: warning: symbol 'unregister_inet6addr_notifier' was not declared. Should it be static?
net/ipv6/addrconf_core.c:106:5: warning: symbol 'inet6addr_notifier_call_chain' was not declared. Should it be static?
net/ipv6/addrconf_core.c:112:5: warning: symbol 'register_inet6addr_validator_notifier' was not declared. Should it be static?
net/ipv6/addrconf_core.c:118:5: warning: symbol 'unregister_inet6addr_validator_notifier' was not declared. Should it be static?
net/ipv6/addrconf_core.c:125:5: warning: symbol 'inet6addr_validator_notifier_call_chain' was not declared. Should it be static?
net/ipv6/addrconf_core.c:237:6: warning: symbol 'in6_dev_finish_destroy' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
We get one warnings when build kernel W=1:
net/sched/sch_taprio.c:1155:6: warning: no previous prototype for ‘taprio_offload_config_changed’ [-Wmissing-prototypes]
Make the function static to fix this.
Fixes: 9c66d15646 ("taprio: Add support for hardware offloading")
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch removes the iph field from the state structure, which is not
properly initialized. Instead, add a new field to make the "do we want
to set DF" be the state bit and move the code to set the DF flag from
ip_frag_next().
Joint work with Pablo and Linus.
Fixes: 19c3401a91 ("net: ipv4: place control buffer handling away from fragmentation iterators")
Reported-by: Patrick Schönthaler <patrick@notvads.ovh>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"I was battling a cold after some recent trips, so quite a bit piled up
meanwhile, sorry about that.
Highlights:
1) Fix fd leak in various bpf selftests, from Brian Vazquez.
2) Fix crash in xsk when device doesn't support some methods, from
Magnus Karlsson.
3) Fix various leaks and use-after-free in rxrpc, from David Howells.
4) Fix several SKB leaks due to confusion of who owns an SKB and who
should release it in the llc code. From Eric Biggers.
5) Kill a bunc of KCSAN warnings in TCP, from Eric Dumazet.
6) Jumbo packets don't work after resume on r8169, as the BIOS resets
the chip into non-jumbo mode during suspend. From Heiner Kallweit.
7) Corrupt L2 header during MPLS push, from Davide Caratti.
8) Prevent possible infinite loop in tc_ctl_action, from Eric
Dumazet.
9) Get register bits right in bcmgenet driver, based upon chip
version. From Florian Fainelli.
10) Fix mutex problems in microchip DSA driver, from Marek Vasut.
11) Cure race between route lookup and invalidation in ipv4, from Wei
Wang.
12) Fix performance regression due to false sharing in 'net'
structure, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (145 commits)
net: reorder 'struct net' fields to avoid false sharing
net: dsa: fix switch tree list
net: ethernet: dwmac-sun8i: show message only when switching to promisc
net: aquantia: add an error handling in aq_nic_set_multicast_list
net: netem: correct the parent's backlog when corrupted packet was dropped
net: netem: fix error path for corrupted GSO frames
macb: propagate errors when getting optional clocks
xen/netback: fix error path of xenvif_connect_data()
net: hns3: fix mis-counting IRQ vector numbers issue
net: usb: lan78xx: Connect PHY before registering MAC
vsock/virtio: discard packets if credit is not respected
vsock/virtio: send a credit update when buffer size is changed
mlxsw: spectrum_trap: Push Ethernet header before reporting trap
net: ensure correct skb->tstamp in various fragmenters
net: bcmgenet: reset 40nm EPHY on energy detect
net: bcmgenet: soft reset 40nm EPHYs before MAC init
net: phy: bcm7xxx: define soft_reset for 40nm EPHY
net: bcmgenet: don't set phydev->link from MAC
net: Update address for MediaTek ethernet driver in MAINTAINERS
ipv4: fix race condition between route lookup and invalidation
...
If there are multiple switch trees on the device, only the last one
will be listed, because the arguments of list_add_tail are swapped.
Fixes: 83c0afaec7 ("net: dsa: Add new binding implementation")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If packet corruption failed we jump to finish_segs and return
NET_XMIT_SUCCESS. Seeing success will make the parent qdisc
increment its backlog, that's incorrect - we need to return
NET_XMIT_DROP.
Fixes: 6071bd1aa1 ("netem: Segment GSO packets on enqueue")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To corrupt a GSO frame we first perform segmentation. We then
proceed using the first segment instead of the full GSO skb and
requeue the rest of the segments as separate packets.
If there are any issues with processing the first segment we
still want to process the rest, therefore we jump to the
finish_segs label.
Commit 177b800746 ("net: netem: fix backlog accounting for
corrupted GSO frames") started using the pointer to the first
segment in the "rest of segments processing", but as mentioned
above the first segment may had already been freed at this point.
Backlog corrections for parent qdiscs have to be adjusted.
Fixes: 177b800746 ("net: netem: fix backlog accounting for corrupted GSO frames")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the remote peer doesn't respect the credit information
(buf_alloc, fwd_cnt), sending more data than it can send,
we should drop the packets to prevent a malicious peer
from using all of our memory.
This is patch follows the VIRTIO spec: "VIRTIO_VSOCK_OP_RW data
packets MUST only be transmitted when the peer has sufficient
free buffer space for the payload"
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the user application set a new buffer size value, we should
update the remote peer about this change, since it uses this
information to calculate the credit available.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas found that some forwarded packets would be stuck
in FQ packet scheduler because their skb->tstamp contained
timestamps far in the future.
We thought we addressed this point in commit 8203e2d844
("net: clear skb->tstamp in forwarding paths") but there
is still an issue when/if a packet needs to be fragmented.
In order to meet EDT requirements, we have to make sure all
fragments get the original skb->tstamp.
Note that this original skb->tstamp should be zero in
forwarding path, but might have a non zero value in
output path if user decided so.
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Thomas Bartschies <Thomas.Bartschies@cvk.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse and Ido reported the following race condition:
<CPU A, t0> - Received packet A is forwarded and cached dst entry is
taken from the nexthop ('nhc->nhc_rth_input'). Calls skb_dst_set()
<t1> - Given Jesse has busy routers ("ingesting full BGP routing tables
from multiple ISPs"), route is added / deleted and rt_cache_flush() is
called
<CPU B, t2> - Received packet B tries to use the same cached dst entry
from t0, but rt_cache_valid() is no longer true and it is replaced in
rt_cache_route() by the newer one. This calls dst_dev_put() on the
original dst entry which assigns the blackhole netdev to 'dst->dev'
<CPU A, t3> - dst_input(skb) is called on packet A and it is dropped due
to 'dst->dev' being the blackhole netdev
There are 2 issues in the v4 routing code:
1. A per-netns counter is used to do the validation of the route. That
means whenever a route is changed in the netns, users of all routes in
the netns needs to redo lookup. v6 has an implementation of only
updating fn_sernum for routes that are affected.
2. When rt_cache_valid() returns false, rt_cache_route() is called to
throw away the current cache, and create a new one. This seems
unnecessary because as long as this route does not change, the route
cache does not need to be recreated.
To fully solve the above 2 issues, it probably needs quite some code
changes and requires careful testing, and does not suite for net branch.
So this patch only tries to add the deleted cached rt into the uncached
list, so user could still be able to use it to receive packets until
it's done.
Fixes: 95c47f9cf5 ("ipv4: call dst_dev_put() properly")
Signed-off-by: Wei Wang <weiwan@google.com>
Reported-by: Ido Schimmel <idosch@idosch.org>
Reported-by: Jesse Hathaway <jesse@mbuki-mvuki.org>
Tested-by: Jesse Hathaway <jesse@mbuki-mvuki.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Cc: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
...instead of -EINVAL. An issue was found with older kernel versions
while unplugging a NFS client with pending RPCs, and the wrong error
code here prevented it from recovering once link is back up with a
configured address.
Incidentally, this is not an issue anymore since commit 4f8943f808
("SUNRPC: Replace direct task wakeups from softirq context"), included
in 5.2-rc7, had the effect of decoupling the forwarding of this error
by using SO_ERROR in xs_wake_error(), as pointed out by Benjamin
Coddington.
To the best of my knowledge, this isn't currently causing any further
issue, but the error code doesn't look appropriate anyway, and we
might hit this in other paths as well.
In detail, as analysed by Gonzalo Siero, once the route is deleted
because the interface is down, and can't be resolved and we return
-EINVAL here, this ends up, courtesy of inet_sk_rebuild_header(),
as the socket error seen by tcp_write_err(), called by
tcp_retransmit_timer().
In turn, tcp_write_err() indirectly calls xs_error_report(), which
wakes up the RPC pending tasks with a status of -EINVAL. This is then
seen by call_status() in the SUN RPC implementation, which aborts the
RPC call calling rpc_exit(), instead of handling this as a
potentially temporary condition, i.e. as a timeout.
Return -EINVAL only if the input parameters passed to
ip_route_output_key_hash_rcu() are actually invalid (this is the case
if the specified source address is multicast, limited broadcast or
all zeroes), but return -ENETUNREACH in all cases where, at the given
moment, the given source address doesn't allow resolving the route.
While at it, drop the initialisation of err to -ENETUNREACH, which
was added to __ip_route_output_key() back then by commit
0315e38270 ("net: Fix behaviour of unreachable, blackhole and
prohibit routes"), but actually had no effect, as it was, and is,
overwritten by the fib_lookup() return code assignment, and anyway
ignored in all other branches, including the if (fl4->saddr) one:
I find this rather confusing, as it would look like -ENETUNREACH is
the "default" error, while that statement has no effect.
Also note that after commit fc75fc8339 ("ipv4: dont create routes
on down devices"), we would get -ENETUNREACH if the device is down,
but -EINVAL if the source address is specified and we can't resolve
the route, and this appears to be rather inconsistent.
Reported-by: Stefan Walter <walteste@inf.ethz.ch>
Analysed-by: Benjamin Coddington <bcodding@redhat.com>
Analysed-by: Gonzalo Siero <gsierohu@redhat.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to extend the rcu_read_lock() section in rxrpc_error_report()
and use rcu_dereference_sk_user_data() instead of plain access
to sk->sk_user_data to make sure all rules are respected.
The compiler wont reload sk->sk_user_data at will, and RCU rules
prevent memory beeing freed too soon.
Fixes: f0308fb070 ("rxrpc: Fix possible NULL pointer access in ICMP handling")
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit b0818f80c8.
Started seeing weird behavior after this patch especially in
the IPv6 code path. Haven't root caused it, but since this was
applied to net branch, taking a precautionary measure to revert
it and look / analyze those failures
Revert this now and I'll send a better fix after analysing / fixing
the weirdness observed.
CC: Eric Dumazet <edumazet@google.com>
CC: Wei Wang <weiwan@google.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported a memory leak:
BUG: memory leak, unreferenced object 0xffff888120b3d380 (size 64):
backtrace:
[...] slab_alloc mm/slab.c:3319 [inline]
[...] kmem_cache_alloc+0x13f/0x2c0 mm/slab.c:3483
[...] sctp_bucket_create net/sctp/socket.c:8523 [inline]
[...] sctp_get_port_local+0x189/0x5a0 net/sctp/socket.c:8270
[...] sctp_do_bind+0xcc/0x200 net/sctp/socket.c:402
[...] sctp_bindx_add+0x4b/0xd0 net/sctp/socket.c:497
[...] sctp_setsockopt_bindx+0x156/0x1b0 net/sctp/socket.c:1022
[...] sctp_setsockopt net/sctp/socket.c:4641 [inline]
[...] sctp_setsockopt+0xaea/0x2dc0 net/sctp/socket.c:4611
[...] sock_common_setsockopt+0x38/0x50 net/core/sock.c:3147
[...] __sys_setsockopt+0x10f/0x220 net/socket.c:2084
[...] __do_sys_setsockopt net/socket.c:2100 [inline]
It was caused by when sending msgs without binding a port, in the path:
inet_sendmsg() -> inet_send_prepare() -> inet_autobind() ->
.get_port/sctp_get_port(), sp->bind_hash will be set while bp->port is
not. Later when binding another port by sctp_setsockopt_bindx(), a new
bucket will be created as bp->port is not set.
sctp's autobind is supposed to call sctp_autobind() where it does all
things including setting bp->port. Since sctp_autobind() is called in
sctp_sendmsg() if the sk is not yet bound, it should have skipped the
auto bind.
THis patch is to avoid calling inet_autobind() in inet_send_prepare()
by changing sctp_prot .no_autobind with true, also remove the unused
.get_port.
Reported-by: syzbot+d44f7bbebdea49dbc84a@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a application sends many packets with the same txtime, they may
be transmitted out of order (different from the order in which they
were enqueued).
This happens because when inserting elements into the tree, when the
txtime of two packets are the same, the new packet is inserted at the
left side of the tree, causing the reordering. The only effect of this
change should be that packets with the same txtime will be transmitted
in the order they are enqueued.
The application in question (the AVTP GStreamer plugin, still in
development) is sending video traffic, in which each video frame have
a single presentation time, the problem is that when packetizing,
multiple packets end up with the same txtime.
The receiving side was rejecting packets because they were being
received out of order.
Fixes: 25db26a913 ("net/sched: Introduce the ETF Qdisc")
Reported-by: Ederson de Souza <ederson.desouza@intel.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot found that if __inet_inherit_port() returns an error,
we call tcp_done() after inet_csk_prepare_forced_close(),
meaning the socket lock is no longer held.
We might fix this in a different way in net-next, but
for 5.4 it seems safer to relax the lockdep check.
Fixes: d983ea6f16 ("tcp: add rcu protection around tp->fastopen_rsk")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the following script:
# tc qdisc add dev eth0 clsact
# tc filter add dev eth0 egress protocol ip matchall \
> action mpls push protocol mpls_uc label 0x355aa bos 1
causes corruption of all IP packets transmitted by eth0. On TC egress, we
can't rely on the value of skb->mac_len, because it's 0 and a MPLS 'push'
operation will result in an overwrite of the first 4 octets in the packet
L2 header (e.g. the Destination Address if eth0 is an Ethernet); the same
error pattern is present also in the MPLS 'pop' operation. Fix this error
in act_mpls data plane, computing 'mac_len' as the difference between the
network header and the mac header (when not at TC ingress), and use it in
MPLS 'push'/'pop' core functions.
v2: unbreak 'make htmldocs' because of missing documentation of 'mac_len'
in skb_mpls_pop(), reported by kbuild test robot
CC: Lorenzo Bianconi <lorenzo@kernel.org>
Fixes: 2a2ea50870 ("net: sched: add mpls manipulation actions to TC")
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the following script:
# tc qdisc add dev eth0 clsact
# tc filter add dev eth0 egress matchall action mpls pop
implicitly makes the kernel drop all packets transmitted by eth0, if they
don't have a MPLS header. This behavior is uncommon: other encapsulations
(like VLAN) just let the packet pass unmodified. Since the result of MPLS
'pop' operation would be the same regardless of the presence / absence of
MPLS header(s) in the original packet, we can let skb_mpls_pop() return 0
when dealing with non-MPLS packets.
For the OVS use-case, this is acceptable because __ovs_nla_copy_actions()
already ensures that MPLS 'pop' operation only occurs with packets having
an MPLS Ethernet type (and there are no other callers in current code, so
the semantic change should be ok).
v2: better documentation of use-cases for skb_mpls_pop(), thanks to Simon
Horman
Fixes: 2a2ea50870 ("net: sched: add mpls manipulation actions to TC")
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While invalidating the dst, we assign backhole_netdev instead of
loopback device. However, this device does not have idev pointer
and hence no ip6_ptr even if IPv6 is enabled. Possibly this has
triggered the syzbot reported crash.
The syzbot report does not have reproducer, however, this is the
only device that doesn't have matching idev created.
Crash instruction is :
static inline bool ip6_ignore_linkdown(const struct net_device *dev)
{
const struct inet6_dev *idev = __in6_dev_get(dev);
return !!idev->cnf.ignore_routes_with_linkdown; <= crash
}
Also ipv6 always assumes presence of idev and never checks for it
being NULL (as does the above referenced code). So adding a idev
for the blackhole_netdev to avoid this class of crashes in the future.
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of tcp_poll(), there are few places where we fetch
sk->sk_wmem_queued while this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make sure write
sides use corresponding WRITE_ONCE() to avoid store-tearing.
sk_wmem_queued_add() helper is added so that we can in
the future convert to ADD_ONCE() or equivalent if/when
available.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of tcp_poll(), there are few places where we fetch
sk->sk_sndbuf while this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make sure write
sides use corresponding WRITE_ONCE() to avoid store-tearing.
Note that other transports probably need similar fixes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of tcp_poll(), there are few places where we fetch
sk->sk_rcvbuf while this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make sure write
sides use corresponding WRITE_ONCE() to avoid store-tearing.
Note that other transports probably need similar fixes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There two places where we fetch tp->urg_seq while
this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make
sure write side use corresponding WRITE_ONCE() to avoid
store-tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where we fetch tp->snd_nxt while
this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make
sure write sides use corresponding WRITE_ONCE() to avoid
store-tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where we fetch tp->write_seq while
this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make
sure write sides use corresponding WRITE_ONCE() to avoid
store-tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where we fetch tp->copied_seq while
this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make
sure write sides use corresponding WRITE_ONCE() to avoid
store-tearing.
Note that tcp_inq_hint() was already using READ_ONCE(tp->copied_seq)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where we fetch tp->rcv_nxt while
this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make
sure write sides use corresponding WRITE_ONCE() to avoid
store-tearing.
Note that tcp_inq_hint() was already using READ_ONCE(tp->rcv_nxt)
syzbot reported :
BUG: KCSAN: data-race in tcp_poll / tcp_queue_rcv
write to 0xffff888120425770 of 4 bytes by interrupt on cpu 0:
tcp_rcv_nxt_update net/ipv4/tcp_input.c:3365 [inline]
tcp_queue_rcv+0x180/0x380 net/ipv4/tcp_input.c:4638
tcp_rcv_established+0xbf1/0xf50 net/ipv4/tcp_input.c:5616
tcp_v4_do_rcv+0x381/0x4e0 net/ipv4/tcp_ipv4.c:1542
tcp_v4_rcv+0x1a03/0x1bf0 net/ipv4/tcp_ipv4.c:1923
ip_protocol_deliver_rcu+0x51/0x470 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5004
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5118
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5208
napi_skb_finish net/core/dev.c:5671 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5704
receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
read to 0xffff888120425770 of 4 bytes by task 7254 on cpu 1:
tcp_stream_is_readable net/ipv4/tcp.c:480 [inline]
tcp_poll+0x204/0x6b0 net/ipv4/tcp.c:554
sock_poll+0xed/0x250 net/socket.c:1256
vfs_poll include/linux/poll.h:90 [inline]
ep_item_poll.isra.0+0x90/0x190 fs/eventpoll.c:892
ep_send_events_proc+0x113/0x5c0 fs/eventpoll.c:1749
ep_scan_ready_list.constprop.0+0x189/0x500 fs/eventpoll.c:704
ep_send_events fs/eventpoll.c:1793 [inline]
ep_poll+0xe3/0x900 fs/eventpoll.c:1930
do_epoll_wait+0x162/0x180 fs/eventpoll.c:2294
__do_sys_epoll_pwait fs/eventpoll.c:2325 [inline]
__se_sys_epoll_pwait fs/eventpoll.c:2311 [inline]
__x64_sys_epoll_pwait+0xcd/0x170 fs/eventpoll.c:2311
do_syscall_64+0xcf/0x2f0 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 7254 Comm: syz-fuzzer Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both tcp_v4_err() and tcp_v6_err() do the following operations
while they do not own the socket lock :
fastopen = tp->fastopen_rsk;
snd_una = fastopen ? tcp_rsk(fastopen)->snt_isn : tp->snd_una;
The problem is that without appropriate barrier, the compiler
might reload tp->fastopen_rsk and trigger a NULL deref.
request sockets are protected by RCU, we can simply add
the missing annotations and barriers to solve the issue.
Fixes: 168a8f5805 ("tcp: TCP Fast Open Server - main code path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf 2019-10-12
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) a bunch of small fixes. Nothing critical.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If an ICMP packet comes in on the UDP socket backing an AF_RXRPC socket as
the UDP socket is being shut down, rxrpc_error_report() may get called to
deal with it after sk_user_data on the UDP socket has been cleared, leading
to a NULL pointer access when this local endpoint record gets accessed.
Fix this by just returning immediately if sk_user_data was NULL.
The oops looks like the following:
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
...
RIP: 0010:rxrpc_error_report+0x1bd/0x6a9
...
Call Trace:
? sock_queue_err_skb+0xbd/0xde
? __udp4_lib_err+0x313/0x34d
__udp4_lib_err+0x313/0x34d
icmp_unreach+0x1ee/0x207
icmp_rcv+0x25b/0x28f
ip_protocol_deliver_rcu+0x95/0x10e
ip_local_deliver+0xe9/0x148
__netif_receive_skb_one_core+0x52/0x6e
process_backlog+0xdc/0x177
net_rx_action+0xf9/0x270
__do_softirq+0x1b6/0x39a
? smpboot_register_percpu_thread+0xce/0xce
run_ksoftirqd+0x1d/0x42
smpboot_thread_fn+0x19e/0x1b3
kthread+0xf1/0xf6
? kthread_delayed_work_timer_fn+0x83/0x83
ret_from_fork+0x24/0x30
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Reported-by: syzbot+611164843bd48cc2190c@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable bugfixes:
- Fix O_DIRECT accounting of number of bytes read/written # v4.1+
Other fixes:
- Fix nfsi->nrequests count error on nfs_inode_remove_request()
- Remove redundant mirror tracking in O_DIRECT
- Fix leak of clp->cl_acceptor string
- Fix race to sk_err after xs_error_report
-----BEGIN PGP SIGNATURE-----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=XDan
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.4-2' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client bugfixes from Anna Schumaker:
"Stable bugfixes:
- Fix O_DIRECT accounting of number of bytes read/written # v4.1+
Other fixes:
- Fix nfsi->nrequests count error on nfs_inode_remove_request()
- Remove redundant mirror tracking in O_DIRECT
- Fix leak of clp->cl_acceptor string
- Fix race to sk_err after xs_error_report"
* tag 'nfs-for-5.4-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
SUNRPC: fix race to sk_err after xs_error_report
NFSv4: Fix leak of clp->cl_acceptor string
NFS: Remove redundant mirror tracking in O_DIRECT
NFS: Fix O_DIRECT accounting of number of bytes read/written
nfs: Fix nfsi->nrequests count error on nfs_inode_remove_request
fallthrough will become a pseudo reserved keyword so this only use of
fallthrough is better renamed to allow it.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
smc_rx_recvmsg() first checks if data is available, and then if
RCV_SHUTDOWN is set. There is a race when smc_cdc_msg_recv_action() runs
in between these 2 checks, receives data and sets RCV_SHUTDOWN.
In that case smc_rx_recvmsg() would return from receive without to
process the available data.
Fix that with a final check for data available if RCV_SHUTDOWN is set.
Move the check for data into a function and call it twice.
And use the existing helper smc_rx_data_available().
Fixes: 952310ccf2 ("smc: receive data from RMBE")
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
smc_cdc_rxed_any_close_or_senddone() is used as an end condition for the
receive loop. This conflicts with smc_cdc_msg_recv_action() which could
run in parallel and set the bits checked by
smc_cdc_rxed_any_close_or_senddone() before the receive is processed.
In that case we could return from receive with no data, although data is
available. The same applies to smc_rx_wait().
Fix this by checking for RCV_SHUTDOWN only, which is set in
smc_cdc_msg_recv_action() after the receive was actually processed.
Fixes: 952310ccf2 ("smc: receive data from RMBE")
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
If creation of an SMCD link group with VLAN id fails, the initial
smc_ism_get_vlan() step has to be reverted as well.
Fixes: c6ba7c9ba4 ("net/smc: add base infrastructure for SMC-D and ISM")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Since commit 4f8943f808 ("SUNRPC: Replace direct task wakeups from
softirq context") there has been a race to the value of the sk_err if both
XPRT_SOCK_WAKE_ERROR and XPRT_SOCK_WAKE_DISCONNECT are set. In that case,
we may end up losing the sk_err value that existed when xs_error_report was
called.
Fix this by reverting to the previous behavior: instead of using SO_ERROR
to retrieve the value at a later time (which might also return sk_err_soft),
copy the sk_err value onto struct sock_xprt, and use that value to wake
pending tasks.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Fixes: 4f8943f808 ("SUNRPC: Replace direct task wakeups from softirq context")
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
sk->sk_backlog.len can be written by BH handlers, and read
from process contexts in a lockless way.
Note the write side should also use WRITE_ONCE() or a variant.
We need some agreement about the best way to do this.
syzbot reported :
BUG: KCSAN: data-race in tcp_add_backlog / tcp_grow_window.isra.0
write to 0xffff88812665f32c of 4 bytes by interrupt on cpu 1:
sk_add_backlog include/net/sock.h:934 [inline]
tcp_add_backlog+0x4a0/0xcc0 net/ipv4/tcp_ipv4.c:1737
tcp_v4_rcv+0x1aba/0x1bf0 net/ipv4/tcp_ipv4.c:1925
ip_protocol_deliver_rcu+0x51/0x470 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5004
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5118
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5208
napi_skb_finish net/core/dev.c:5671 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5704
receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
virtnet_receive drivers/net/virtio_net.c:1323 [inline]
virtnet_poll+0x436/0x7d0 drivers/net/virtio_net.c:1428
napi_poll net/core/dev.c:6352 [inline]
net_rx_action+0x3ae/0xa50 net/core/dev.c:6418
read to 0xffff88812665f32c of 4 bytes by task 7292 on cpu 0:
tcp_space include/net/tcp.h:1373 [inline]
tcp_grow_window.isra.0+0x6b/0x480 net/ipv4/tcp_input.c:413
tcp_event_data_recv+0x68f/0x990 net/ipv4/tcp_input.c:717
tcp_rcv_established+0xbfe/0xf50 net/ipv4/tcp_input.c:5618
tcp_v4_do_rcv+0x381/0x4e0 net/ipv4/tcp_ipv4.c:1542
sk_backlog_rcv include/net/sock.h:945 [inline]
__release_sock+0x135/0x1e0 net/core/sock.c:2427
release_sock+0x61/0x160 net/core/sock.c:2943
tcp_recvmsg+0x63b/0x1a30 net/ipv4/tcp.c:2181
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1864 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7292 Comm: syz-fuzzer Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Guillaume Nault