The mpc_i2c_fixup function is called when the bus is not released by a
slave. The function generates 9 pulses that should lead the slave
to release the bus.
The sequence that generates the pulses disables/enables the I2C module
that controls the blocked bus. We have found out on the P2041 SoC that
this could cause the CPU to hang (for a short delay).
To avoid this, this patch introduces a read to the I2CDR register
between the re-enablement of the I2C module in master mode and its
returning to the slave mode instead of the delay (the final delay,
between the pulses is kept), as proposed in procedure from the P2041
reference manual (16.6.2.3), and the other manuals from the mpc83xx and
mpc85xx families.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message. For example,
k.alloc and v.alloc failures use dump_stack().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Intel Haswell has the same I2C host controller than Baytrail and it can
also be enumerated as a PCI device. Add the PCI IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is possible that after entering runtime PM suspend the controller
context is lost due the fact that its power is removed. This happens for
example on Asus T100, an Intel Baytrail based tablet/laptop.
In order to get the controller back to functional state, we need to
implement runtime PM hooks which will re-initialize the hardware during
runtime PM resume. We can re-use the existing system suspend hooks as the
steps to resume/suspend the controller are the same.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Userspace can initiate system suspend on arbitrary times which means that
device drivers must make sure that their device gets quiesced before system
suspend is entered. Therefore disable the I2C host controller in the driver
system suspend hook.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Arnd said in another patch:
"As far as I can tell, this driver must have produced this
error for as long as it has been merged into the mainline kernel, but
it was never part of the normal build tests:
drivers/i2c/busses/i2c-nuc900.c: In function 'nuc900_i2c_probe':
drivers/i2c/busses/i2c-nuc900.c:601:17: error: request for member
'apbfreq' in something not a structure or union
ret = (i2c->clk.apbfreq)/(pdata->bus_freq * 5) - 1;
^
This is an attempt to get the driver to build and possibly
work correctly, although I do wonder whether we should just
remove it, as it has clearly never worked."
I agree with removing it since nobody showed interest in Arnd's fixup
patch.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Wan ZongShun <mcuos.com@gmail.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Since IMX serial SOCs support low bus freq mode, some clocks freq
may change to save power. I2C needs to check the clock source and
update the divider.
For example:
i.MX6SL I2C clk is from IPG_PERCLK which is sourced from IPG_CLK.
Under normal operation, IPG_CLK is 66MHz, ipg_perclk is at 22MHz.
In low bus freq mode, IPG_CLK is at 12MHz and IPG_PERCLK is down
to 4MHz. So the I2C driver must update the divider register for
each transaction when the current IPG_PERCLK is not equal to the
clock of previous transaction.
Signed-off-by: Fugang Duan <B38611@freescale.com>
[wsa: removed an outdated comment and simplified debug output]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Test i2c device Maxim max44009, datasheet is located at:
http://www.maximintegrated.com/datasheet/index.mvp/id/7175
The max44009 support repeat operation like:
read -> repeat restart -> read/write
The current i2c imx host controller driver don't support this
operation that causes i2c bus hang due to "MTX" is cleared in
.i2c_imx_read(). If "read" is the last message there have no problem,
so the current driver supports all SMbus operation like:
write -> repeat restart -> read/write
IMX i2c controller for master receiver has some limitation:
- If it is the last byte for one operation, it must generate STOP
signal before read I2DR to prevent controller from generating another
clock cycle.
- If it is the last byte in the read, and then do repeat restart, it must
set "MTX" before read I2DR to prevent controller from generating another
extra clock cycle.
The patch is to fix the issue.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make clear that the driver is GPL v2 only. Remove FSF address. Remove
filename in comment. Update copyright information.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove some obvious comments, remove some superfluous debug output (the
error code carries the same information), some white space fixing...
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Status register and enable register are identical regarding their
layout. Use the bit definitions for both.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c core has per-adapter locks, so no need to protect again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The old macros made it harder to see what was actually happening.
Replace them with something more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Setting up a read or write message is similar enough to be done in one
function. Also, move a helper function into the new function since it is
only used here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We should always check if the bus is free, independently if it is a read
or write. It should be done before the first message, though. After
that, we ourselves keep the bus busy. Remove a 'ret' assignment which
only silenced a build warning.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the seperate functions and use designated constants. As readable
but less overhead. Actually, this is even more readable since the old
function used a mix of "=" and "|=".
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the seperate functions and use designated constants. As readable
but less overhead.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We use devm, so irq number is only needed during probe.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Very basic operations, just called once, can also go to the caller.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch the device tree to the new compatibles introduced in the i2c drivers
to have a common pattern accross all Allwinner SoCs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_gpio_request() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Violeta Menendez <violeta.menendez@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
Tested-by: Violeta Menendez <violeta.menendez@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-eg20t driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Newer SoCs have so fast input clocks that the ICCL/H registers only
count every second clock to have a meaningful 9-bit range. The driver
was already prepared for that happening, but didn't use it so far.
Add the proper DT configuration for SoCs that need it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to misconfiguration, it can happen that the calculated timing
parameters are out of range. Bail out if that happens. We can also
simplify some logic later because of the verified value. Also, make the
printouts of the values more precise by adding the hex-prefixes.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
sh_mobile_i2c_init() could detect wrong settings, but didn't bail out,
so it would continue unconfigured. Fix this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Following the KISS principle, remove unneeded stuff.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is what devm was made for. No rollback mechanism needed, remove the
hook parameter from the irq setup function and simplify it. While we are
here change some variables to proper types.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Convert the easy parts to devm. irqs will be converted in a seperate
patch to keep diffs readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use standard i2c error codes for i2c failures. Also, don't print
something on timeout since it happens regularly with i2c. Simplify some,
logic, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No functional change, binaries are identical.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
HSI2C module on Exynos5260 differs from current modules in
following ways:
1. HSI2C on Exynos5260 has fifo_depth of 16bytes
2. Module needs to be reset as a part of init sequence.
Hence, Following changes are involved.
1. Add a new compatible string and Updates the Documentation dt bindings.
2. Introduce a variant struct to support the changes in H/W
3. Reset the module during init. Thus, bringing the module back
to default state irrespective of what firmware did with it.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This adds some more warnings to the i2c-arb-gpio-challenge docs to
help encourage people not to use it in their designs unless they have
no choice.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixed most checkpatch.pl issues
Signed-off-by: Richard Leitner <me@g0hl1n.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For !CONFIG_PM_RUNTIME, the device were never put back into active
state while resuming.
For CONFIG_PM_RUNTIME, we blindly trusted the device to be inactive
while we were about to handle it at suspend late, which is just too
optimistic.
Even if the driver uses pm_runtime_put_sync() after each tranfer to
return it's runtime PM resources, there are no guarantees this will
actually mean the device will inactivated. The reason is that the PM
core will prevent runtime suspend during system suspend, and thus when
a transfer occurs during the early phases of system suspend the device
will be kept active after the transfer.
To handle both issues above, use pm_runtime_force_suspend|resume() from
the system suspend|resume callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The smbus block read is not currently supported for imx i2c devices.
This patchset adds the support to imx i2c bus so that blocks of data
can be read using SMbus block reads.(using i2c_smbus_read_block_data()
function from the i2c_core.c.). Tested with 3.10.9 kernel.
Reviewed-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Kaushal Butala <kaushalkernelmailinglist@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Move to the other
pattern for consistency across all Allwinner Socs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wsa: dropped binding OK as per
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-February/229438.html]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull two powerpc fixes from Ben Herrenschmidt:
"Here are a couple of fixes for 3.15. One from Anton fixes a nasty
regression I introduced when trying to fix a loss of irq_work whose
consequences is that we can completely lose timer interrupts on a
CPU... not pretty.
The other one is a change to our PCIe reset hook to use a firmware
call instead of direct config space accesses to trigger a fundamental
reset on the root port. This is necessary so that the FW gets a
chance to disable the link down error monitoring, which would
otherwise trip and cause subsequent fatal EEH error"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: irq work racing with timer interrupt can result in timer interrupt hang
powerpc/powernv: Reset root port in firmware
Pull two btrfs fixes from Chris Mason:
"This has two fixes that we've been testing for 3.16, but since both
are safe and fix real bugs, it makes sense to send for 3.15 instead"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: send, fix incorrect ref access when using extrefs
Btrfs: fix EIO on reading file after ioctl clone works on it
Pull two ceph fixes from Sage Weil:
"The first patch fixes a problem when we have a page count of 0 for
sendpage which is triggered by zfs. The second fixes a bug in CRUSH
that was resolved in the userland code a while back but fell through
the cracks on the kernel side"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
crush: decode and initialize chooseleaf_vary_r
libceph: fix corruption when using page_count 0 page in rbd
Code inspection of the XFS error number sign translations found a bunch of
issues, including returning incorrectly signed errors for some data integrity
operations. These leak to userspace and result in applications not getting the
errors correctly reported. Hence they need fixing sooner rather than later.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=5syB
-----END PGP SIGNATURE-----
Merge tag 'xfs-for-linus-3.15-rc6' of git://oss.sgi.com/xfs/xfs
Pull xfs fixes from Dave Chinner:
"Code inspection of the XFS error number sign translations found a
bunch of issues, including returning incorrectly signed errors for
some data integrity operations.
These leak to userspace and result in applications not getting the
errors correctly reported. Hence they need fixing sooner rather than
later.
A couple of the bugs are in data integrity operations, a couple more
are in the new COLLAPSE_RANGE code. One of these came in through a
recent ext4 merge and so I had to update the base tree to 3.15-rc5
before fixing the issues"
* tag 'xfs-for-linus-3.15-rc6' of git://oss.sgi.com/xfs/xfs:
xfs: list_lru_init returns a negative error
xfs: negate xfs_icsb_init_counters error value
xfs: negate mount workqueue init error value
xfs: fix wrong err sign on xfs_set_acl()
xfs: fix wrong errno from xfs_initxattrs
xfs: correct error sign on COLLAPSE_RANGE errors
xfs: xfs_commit_metadata returns wrong errno
xfs: fix incorrect error sign in xfs_file_aio_read
xfs: xfs_dir_fsync() returns positive errno
Pull renameat2 arch support from Miklos Szeredi:
"I've collected architecture patches for the renameat2 syscall that
maintainers acked and/or asked me to queue.
This adds architecture support for the renameat2 syscall to m68k,
parisc, ia64 and through asm-generic to arc, arm64, c6x, hexagon,
metag, openrisc, score, tile, unicore32"
* 'renameat2' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
scripts/checksyscalls.sh: Make renameat optional
asm-generic: Add renameat2 syscall
ia64: add renameat2 syscall
parisc: add renameat2 syscall
m68k: add renameat2 syscall
3 Fixes for the AMD IOMMU driver:
* Fix a locking issue around get_user_pages()
* Fix 2 issues with device aliasing and
exclusion range handling
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3Wdm
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v3.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"Three fixes for the AMD IOMMU driver:
- fix a locking issue around get_user_pages()
- fix two issues with device aliasing and exclusion range handling"
* tag 'iommu-fixes-v3.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: fix enabling exclusion range for an exact device
iommu/amd: Take mmap_sem when calling get_user_pages
iommu/amd: Fix interrupt remapping for aliased devices
Valentin Longchamp