Addresses the following, which introduced a regression itself:
Commit 509f89652f ("media: em28xx: fix a regression with HVR-950")
The regression fix breaks dual transport stream support. Currently,
when a tuner starts streaming it sets alt mode on the USB interface.
The problem is, in a dual tuner model, both tuners share the same
USB interface, so when the second tuner becomes active and sets alt
mode on the interface it kills streaming on the other port.
This patch addresses the regression by only setting alt mode
on the USB interface during em28xx_start_streaming, if the
device is not a dual tuner model. This allows all older and
single tuner devices to explicitly set alt mode during stream
startup. Testers report both isoc and bulk DualHD models work
correctly with the alt mode set only once, in em28xx_dvb_init.
Fixes: 509f89652f ("media: em28xx: fix a regression with HVR-950")
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Michael Ira Krufky <mkrufky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The use of a hard coded i2c address breaks the creation of the
second tuner in DualHD 01595 models. The issue is compounded
by lack of any error message stating that a driver failed
initialization. Use addr, which contains the correct address
for each tuner.
Fixes: ad32495b15 ("media: em28xx-dvb: simplify DVB module probing logic")
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Extra code to be able to use this stick, only digital, not analog
nor remote-control.
Signed-off-by: Marcel Stork <mjstork@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Convert the driver to allow its usage with the new I2C
binding way.
Please notice that this patch doesn't convert the
callers to bind to it using the new way.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit be7fd3c3a8 ("media: em28xx: Hauppauge DualHD second tuner
functionality") removed the logic with sets the alternate for the DVB
device. Without setting the right alternate, the device won't be
able to submit URBs, and userspace fails with -EMSGSIZE:
ERROR DMX_SET_PES_FILTER failed (PID = 0x2000): 90 Message too long
Tested with Hauppauge HVR-950 model A1C0.
Fixes: be7fd3c3a8 ("media: em28xx: Hauppauge DualHD second tuner functionality")
Cc: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
From now on, I'll start using my @kernel.org as my development e-mail.
As such, let's remove the entries that point to the old
mchehab@s-opensource.com at MAINTAINERS file.
For the files written with a copyright with mchehab@s-opensource,
let's keep Samsung on their names, using mchehab+samsung@kernel.org,
in order to keep pointing to my employer, with sponsors the work.
For the files written before I join Samsung (on July, 4 2013),
let's just use mchehab@kernel.org.
For bug reports, we can simply point to just kernel.org, as
this will reach my mchehab+samsung inbox anyway.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Brian Warner <brian.warner@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Hauppauge Solo/Dual HD DVB models use a si2157 tuner, which is set to
produce inverted spectrum. This configures the si2168 DVB demod for
inverted spectrum on both affected models.
[mchehab@s-opensource.com: rebased on the top of upstream]
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Most of the files there are missing a SPDX license tag. Add.
While here fix some DRIVER_LICENSE macro in order to reflect
the source file license, as some of the headers are GPL v2
only.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we're touching a lot on this file, let's solve several
Coding Style issues there using checkpatch --fix-inline --strict,
and manually adjusting the results.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is a typo at the several s5h14*.h headers: continuous were
spelled incorrectly.
Fix it with this script:
for i in $(git grep -l S5H1409_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK); do
sed s,S5H1409_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK,S5H1409_MPEGTIMING_CONTINUOUS_NONINVERTING_CLOCK,g -i $i
done
for i in $(git grep -l -i continous drivers/media); do sed s,CONTINOUS,CONTINUOUS,g -i $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The module probing logic there is a way more complex than
it should be, and requires some special magic to avoid
stack overflows when KASAN is enabled.
Solve it by creating ancillary functions to setup the
platform data and request module.
Now, the probing functions are cleaner and easier to understand.
As a side effect, the size of the module was reduced by
about 9.7% on x86_64:
Before this patch:
text data bss dec hex filename
51090 14192 96 65378 ff62 drivers/media/usb/em28xx/em28xx-dvb.o
After this patch:
text data bss dec hex filename
44743 14192 96 59031 e697 drivers/media/usb/em28xx/em28xx-dvb.o
Tested with a PCTV 461e device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With CONFIG_KASAN, the init function uses a large amount of kernel stack:
drivers/media/usb/em28xx/em28xx-dvb.c: In function 'em28xx_dvb_init.part.4':
drivers/media/usb/em28xx/em28xx-dvb.c:2061:1: error: the frame size of 3232 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
Using gcc-7 with -fsanitize-address-use-after-scope makes this even worse:
drivers/media/usb/em28xx/em28xx-dvb.c: In function 'em28xx_dvb_init':
drivers/media/usb/em28xx/em28xx-dvb.c:2069:1: error: the frame size of 4280 bytes is larger than 3072 bytes [-Werror=frame-larger-than=]
By splitting out each part of the switch/case statement that has its own local
variables into a separate function, no single one of them uses more than 500 bytes,
and with a noinline_for_stack annotation we can ensure that they are not merged
back together.
[mchehab@s-opensource.com: fix conflict with changeset
be7fd3c3a8 ("media: em28xx: Hauppauge DualHD second tuner functionality")]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement use of secondary TS port on em28xx.
Adds has_dual_ts field, allows secondary demod/tuner to be
added to a single em28xx device.
Hauppauge DualHD models are configured to use this feature.
[mchehab@s-opensource.com: em28xx_duplicate_dev() should be static]
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Trivial fix to spelling mistake in error message text
[mchehab@s-opensource.org: folded all similar patches into one]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hauppauge WinTV-dualHD model 01595 is a USB 2.0 dual ATSC/QAM tuner with
the following components:
USB bridge: Empia em28274
Demodulator: 2x LG LGDT3306a at addresses 0xb2 and 0x1c
Tuner: 2x Silicon Labs si2157 at addresses 0xc0 and 0xc4
This patch enables only the first tuner.
Signed-off-by: Kevin Cheng <kcheng@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that we're storing usb_interface at em28xx struct,
there's no good reason to keep storing usb_device, as we can
get it from usb_interface. So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The usb_device->dev is not the right device for dev_foo() calls.
Instead, it should use usb_interface->dev.
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of using pr_foo(), use dev_foo(), with provides a
better output. As this device is a multi-interface one,
we'll set the device name to show the chipset and the driver
used.
While here, get rid of printk continuation messages.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are still several places with printk's called directly.
Convert them to pr_foo() macros, except for the debug printk's,
as those are enabled via modprobe vars.
While here, realign the pr_foo() arguments to match the
recommended CodingStyle.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols checkpatch warnings, several strings
were broken into multiple lines. This is not considered
a good practice anymore, as it makes harder to grep for
strings at the source code. So, join those continuation
lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Gcc 6.1 warns about an unused table:
drivers/media/usb/em28xx/em28xx-dvb.c:907:38: warning: 'pctv_461e_m88ds3103_config' defined but not used [-Wunused-const-variable=]
static const struct m88ds3103_config pctv_461e_m88ds3103_config = {
^~~~~~~~~~~~~~~~~~~~~~~~~~
That's a left over of patch 76b91be3d3 ('em28xx: PCTV 461e use I2C
client for demod and SEC').
Remove the dead code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hauppauge WinTV-dualHD is a USB 2.0 dual DVB-T/T2/C tuner with
following components:
USB bridge: Empia EM28274 (chip id is the same as EM28174)
Demodulator: 2x Silicon Labs Si2168-B40
Tuner: 2x Silicon Labs Si2157-A30
This patch adds support only for the first tuner.
The demodulator needs firmware, available for example here:
http://palosaari.fi/linux/v4l-dvb/firmware/Si2168/Si2168-B40/4.0.11/
The demodulators sit on the same I2C bus and their addresses
are 0x64 and 0x67. The tuners are behind the demodulators and
their addresses are 0x60 and 0x63.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
PX-BCUD has the following components:
USB interface: Empia EM28178
Demodulator: Toshiba TC90532 (works by code for TC90522)
Tuner: Next version of Sharp QM1D1C0042
em28xx_dvb_init(): add init code for PLEX PX-BCUD with calling
px_bcud_init() that does things like pin configuration.
qm1d1c0042_init(): support the next version of QM1D1C0042, change to
choose an appropriate array of initial registers by reading chip id.
[mchehab@osg.samsung.com: fold a fixup patch and fix checkpatch.pl
errors/warnings, where applicable]
Signed-off-by: Satoshi Nagahama <sattnag@aim.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As si2157 doesn't use the subdev, but has instead a binding
logic that doesn't have any core framework, we need to manually
pass the media_device struct via platform data on every place
it is called.
This fixes support for HVR-955Q when MC is enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When in analog mode, the RF connector will be created by
em28xx-video. However, when the device is in digital mode only,
the RF connector is not shown. In this case, let the DVB
core to create it for us.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Terratec Cinergy T XS is a DVB-T receiver with no analog TV tuner.
This patch adds support for the cards carrying the mt2060 tuner; it's
unclear whether there are cards sold under the same name which use a
different tuner.
As long as there are no reports of such cards, and indeed as long as
there are no working drivers for them, we assume that the USB device
[0ccd:0043] is carrying the mt2060 tuner.
Signed-off-by: Alberto Mardegan <mardy@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Devices that were using a8293 SEC are converted to I2C platform data
thus that old config structure is left unused.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Load PCTV 460e tda10071 demod and a8293 SEC using I2C client bindings.
Remove old unused tda10071 config struct. We are using I2C platform
data now.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The chips supported by the si2157 driver have two IF outputs (either
pins 12+13 or pins 9+11). Instead of hardcoding the output to be used
add an option to choose which output shall be used.
As this patch changes the default behaviour, the IF interface is
specified in each driver currently using si2157 driver. This is to
keep bisectability.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change ts2022 driver to ts2020 driver as ts2020 driver now supports
both models.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch will add basic support for the Elgato EyeTV Hybrid INT
2008 USB Stick.
Signed-off-by: Gilles Risch <gilles.risch@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Inspection shows that newlines are missing from several kernel messages
in em28xx-dvb. Fix these.
Fixes: ca2b46dacb ("[media] em28xx-dvb: implement em28xx_ops: suspend/resume hooks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The lockdep splat addressed in a previous commit revealed that at
least one message in em28xx-input.c was missing a new line:
em28178 #0: Closing input extensionINFO: trying to register non-static key.
Further inspection shows several other messages also miss a new line.
These will be fixed in a subsequent patch.
Fixes: aa929ad783 ("[media] em28xx: print a message at disconnect")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch is basically produced while testing a tool that
Joe Perches sent upstream sometime ago:
https://lkml.org/lkml/2014/7/11/794
I used it with those arguments:
$ reformat_with_checkpatch.sh drivers/media/usb/em28xx/em28xx*.[ch]
It actually produced 24 patches, with is too much, and showed
interesting things: gcc produced different codes on most of the
patches, even with just linespace changes. The total code data
remained the same on all cases I checked though.
Anyway, provided that we fold the resulting patches, this tool
seems useful.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Terratec Cinergy T2 Stick HD [eb1a:8179] is a USB DVB-T/T2/C tuner that
contains following components:
* Empia EM28178 USB bridge
* Silicon Labs Si2168-A30 demodulator
* Silicon Labs Si2146-A10 tuner
I don't have the remote, so the RC_MAP is a best guess based on the pictures of
the remote controllers and other supported Terratec devices with a similar
remote.
[Antti: Resolved conflict caused by Leadtek VC100 patch]
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When new parameters are added for si2168 driver, the parameters have to be explicitly defined for each device if the
si2168_config struct is not initialized to all zeros.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Used tda18212 tuner is implemented as a I2C driver. Use em28xx
tuner I2C client for tda18212 driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
TS mode must be set in the existing PCTV 292e driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement set voltage operation.
Separate TS clock as a own configuration parameter.
Add TS clock polarity parameter.
[crope@iki.fi: merge em28xx driver m88ds3103 config change patch
to that one, in order to keep build unbroken]
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Change em28xx_dvb_fini() to set fe exit flag to DVB_FE_DEVICE_REMOVED
when device is disconnected. em28xx maintains device disconnect status
in em28xx device. fe drivers will be able to now check the fe exit
status to avoid accessing the device, from their release interfaces
when called from disconnect path. This change depends on dvb-core
change that exports fe exit flag by moving it from fepriv to fe.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add error hanlding when EM2870_BOARD_KWORLD_A340 dvb_attach()
for fe and tuner fail in em28xx_dvb_init().
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Brad Love