Since single rf path chips don't support TX SPBC, tell mac80211
to not advertise it.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-5-yhchuang@realtek.com
Beamforming is used for directional signal transmission/reception.
Beamformee plays the role for signal reception, and makes the RX
performance better in middle distance range.
Implement beamformee related callbacks for 8821c.
Since 8821c only support 1ss rate, nc_index in beamformee setting
needs to be adjusted based on the capability.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-4-yhchuang@realtek.com
The TX power requires to be adjusted based on the thermal value.
The actual power will decrease if the thermal value raised, and
will increase if the thermal value lowered. Driver comapres the
thermal value, as moving averages. If it changes over a limit,
driver will modify the TX power index to compensate.
Implement rtw_chip_ops::pwr_track() for 8821c.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-3-yhchuang@realtek.com
CCK PD can reduce the number of false alarm of the CCK rates.
It dynamically adjusts the power threshold and CS ratio.
The values are compared to the values of the previous level, if
the level is changed, set new values of power threshold and CS
ratio.
Implement rtw_chip_ops::cck_pd_set() for 8821c.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-2-yhchuang@realtek.com
In order to get a better TX EVM, do calibration after association.
The calibration needed for 8821c is the IQK, which is done in the
firmware. Implement the rtw_chip_ops::phy_calibration() to trigger
firmware to calibrate.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-8-yhchuang@realtek.com
False alarm statistics can be used to adjust the RX gain. This
helps the driver to adapt to different circumstances.
Implement rtw_chip_ops::false_alarm_statistics() for 8821c.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-7-yhchuang@realtek.com
Some RX packets contain also information about environment status.
Implement rtw_chip_ops::query_rx_desc() for 8821c. Parse the RX
descriptor which describes the current condition of the received
packet.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-6-yhchuang@realtek.com
8821c is capable of 2.4G and 5G.
Implement rtw_chip_ops::set_channel() to set 2G and 5G channels.
This includes MAC, BB and RF related settings.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-5-yhchuang@realtek.com
To improve user experience in field, we need DIG to adjust RX initial
gain depends on field situation.
Define the register addresses for 8821c.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-4-yhchuang@realtek.com
To configure the transmit power of 8821c implement trasmit
power index setting callback function for 8821c. This is very
similar to the callback function of 8822b.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-3-yhchuang@realtek.com
RTL8821CE chipsets are 802.11ac dual-band WiFi + BT combo chips.
This patch adds the basic functions such as parameter tables, chip
information, power on flow.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-2-yhchuang@realtek.com
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type defining 'NETDEV_TX_OK' but this
driver returns '0' instead of 'NETDEV_TX_OK'.
Fix this by returning 'NETDEV_TX_OK' instead of '0'.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200629104009.84077-1-luc.vanoostenryck@gmail.com
Added version number info along with firmware name so driver can pick
the correct revision of FW file. Moved FW filename macro as part of
driver code & added MODULE_FIRMWARE to specify FW needed by module.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-6-ajay.kathat@microchip.com
Modify WILC1000 binary filename to use single unified wilc1000 FW.
A single wilc1000 binary is used for different wilc1000 revisions.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-5-ajay.kathat@microchip.com
Avoid below reported warning found when 'CONFIG_PM' config is
undefined.
'warning: unused variable 'wowlan_support' [-Wunused-const-variable]'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-4-ajay.kathat@microchip.com
Make use 'strlcpy' instead of 'strncpy' to overcome 'stringop-truncation'
compiler warning.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-3-ajay.kathat@microchip.com
As Adham's email address is bouncing, remove him from wilc1000 entry and
add Claudiu as a new co-maintainer. Claudiu follows wilc1000 driver
development for a long time and contributed to it already.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-2-ajay.kathat@microchip.com
The code in the BRCM80211 BRCMSMAC driver is using the legacy
GPIO API to to a complex check of the validity of the base of
the GPIO chip and whether it is present at all and then adding
an offset to the base of the chip.
Use the existing function to obtain a GPIO line internally
from a GPIO chip so we can use the offset directly and
modernize the code to use GPIO descriptors instead of integers
from the global GPIO numberspace.
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Frank Kao <frank.kao@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200711210150.4943-1-linus.walleij@linaro.org
The driver relies on the compatible string from DT to determine which
FW configuration file it should load. The DTS spec allows for '/' as
part of the compatible string. We change this to '-' so that we will
still be able to load the config file, even when the compatible has a
'/'. This fixes explicitly the firmware loading for
"solidrun,cubox-i/q".
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Hans deGoede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200701112201.6449-1-matthias.bgg@kernel.org
Linux 3.6 introduces TSQ which has a per socket threshold for TCP Tx
packet to reduce latency. In flow control mode, host driver enqueues skb
in hanger and TCP doesn't push new skb frees until host frees the skb when
receiving fwstatus event. So set pacing shift 8 to send them as a single
large aggregate frame to the bus layer.
43455 TX TCP throughput in different FC modes on Linux 5.4.18
sk_pacing_shift : Throughput (fcmode=0)
10: 245 Mbps
9: 245 Mbps
8: 246 Mbps
7: 246 Mbps
sk_pacing_shift : Throughput (fcmode=1)
10: 182 Mbps
9: 197 Mbps
8: 206 Mbps
7: 207 Mbps
sk_pacing_shift : Throughput (fcmode=2)
10: 180 Mbps
9: 197 Mbps
8: 206 Mbps
7: 207 Mbps
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200624091608.25154-3-wright.feng@cypress.com
When USB or SDIO device got abnormal bus disconnection, host driver
tried to clean up the skbs in PSQ and TXQ (The skb's pointer in hanger
slot linked to PSQ and TSQ), so we should set the state of skb hanger slot
to BRCMF_FWS_HANGER_ITEM_STATE_FREE before freeing skb.
In brcmf_fws_bus_txq_cleanup it already sets
BRCMF_FWS_HANGER_ITEM_STATE_FREE before freeing skb, therefore we add the
same thing in brcmf_fws_psq_flush to avoid following warning message.
[ 1580.012880] ------------ [ cut here ]------------
[ 1580.017550] WARNING: CPU: 3 PID: 3065 at
drivers/net/wireless/broadcom/brcm80211/brcmutil/utils.c:49
brcmu_pkt_buf_free_skb+0x21/0x30 [brcmutil]
[ 1580.184017] Call Trace:
[ 1580.186514] brcmf_fws_cleanup+0x14e/0x190 [brcmfmac]
[ 1580.191594] brcmf_fws_del_interface+0x70/0x90 [brcmfmac]
[ 1580.197029] brcmf_proto_bcdc_del_if+0xe/0x10 [brcmfmac]
[ 1580.202418] brcmf_remove_interface+0x69/0x190 [brcmfmac]
[ 1580.207888] brcmf_detach+0x90/0xe0 [brcmfmac]
[ 1580.212385] brcmf_usb_disconnect+0x76/0xb0 [brcmfmac]
[ 1580.217557] usb_unbind_interface+0x72/0x260
[ 1580.221857] device_release_driver_internal+0x141/0x200
[ 1580.227152] device_release_driver+0x12/0x20
[ 1580.231460] bus_remove_device+0xfd/0x170
[ 1580.235504] device_del+0x1d9/0x300
[ 1580.239041] usb_disable_device+0x9e/0x270
[ 1580.243160] usb_disconnect+0x94/0x270
[ 1580.246980] hub_event+0x76d/0x13b0
[ 1580.250499] process_one_work+0x144/0x360
[ 1580.254564] worker_thread+0x4d/0x3c0
[ 1580.258247] kthread+0x109/0x140
[ 1580.261515] ? rescuer_thread+0x340/0x340
[ 1580.265543] ? kthread_park+0x60/0x60
[ 1580.269237] ? SyS_exit_group+0x14/0x20
[ 1580.273118] ret_from_fork+0x25/0x30
[ 1580.300446] ------------ [ cut here ]------------
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200624091608.25154-2-wright.feng@cypress.com
commit 4684997d9e ("brcmfmac: reset PCIe bus on a firmware crash")
adds a reset function to recover firmware trap for PCIe bus. This commit
adds an implementation for SDIO bus.
Upon SDIO firmware trap, do below:
- Remove the device
- Reset hardware
- Probe the device again
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622144851.165248-1-chi-hsien.lin@cypress.com
Ignore FW event if the event's BSSID is different form the BSSID of the
currently connected AP. Check interface state is connected or not, if
state is not connected that can ignore link down event.
Signed-off-by: Able Liao <Able.Liao@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200618160739.21457-4-chi-hsien.lin@cypress.com
Current brcmf_link_down() always call cfg80211_disconnected() with
locally_generated=1, which is not always the case. Add event source
argument on link down handler and set locally_generated based on the
real trigger.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200618160739.21457-3-chi-hsien.lin@cypress.com
Unable to change back to visiable SSID because there is
no disable hidden ssid routine.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200618160739.21457-2-chi-hsien.lin@cypress.com
Commit 4905432b28b7 ("brcmfmac: Fix P2P Group Formation failure via Go-neg
method") did not initialize requested_dwell properly, resulting in an
always-false dwell time overflow check. Fix it by setting the correct
requested_dwell value.
Fixes: 4905432b28b7 ("brcmfmac: Fix P2P Group Formation failure via Go-neg method")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Joseph Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-7-chi-hsien.lin@cypress.com
This patch move the credit map setting to right place to avoid
brcmf_fws_return_credits() return without setting the credit map.
It fix the thoughput zero stalls issue in softAP mode when STA
using PM 1 mode.
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-6-chi-hsien.lin@cypress.com
There is a mismatch of tx status flag values between host and firmware.
It makes the host mistake the flags and have incorrect behavior of credit
returns. So update the flags to sync with the firmware ones.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-5-chi-hsien.lin@cypress.com
It is observed that sometimes when sdiod is low in tx credits in low
rssi scenarios, the data path consumes all sdiod rx all credits and
there is no sdiod rx credit available for control path causing host
and card to go out of sync resulting in link loss between host and
card. So in order to prevent it some credits are reserved for control
path.
Note that TXCTL_CREDITS can't be larger than the firmware default
credit update threshold 2; otherwise there will be a deadlock for both
side waiting for each other.
Signed-off-by: Amar Shankar <amsr@cypress.com>
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-4-chi-hsien.lin@cypress.com
In wifi firmware, max length of IOCTL/IOVAR buffer size is 8192.
Increase the message buffer max size same as wifi firmware for control
packets so return buffers can come back.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-3-chi-hsien.lin@cypress.com
Current credit borrowing allows only the access category BE to
borrow the credits. This change is to fix the credit borrowing
logic, to make borrowing available for all access categories
and also to borrow only from the lower categories. This fixes WFA
802.11n certs 5.2.27 failures.
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-2-chi-hsien.lin@cypress.com
Bss info flag definition need to be fixed from 0x2 to 0x4
This flag is for rssi info received on channel.
All Firmware branches defined as 0x4 and this is bug in brcmfmac.
Signed-off-by: Prasanna Kerekoppa <prasanna.kerekoppa@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-6-wright.feng@cypress.com
The firmware state machines are not fully suitable for concurrent
station interface support, it may hit unexpected error if we have 2
different SSIDs and the roaming scenarios concurrently.
To avoid the bad user-experience if this is not fully validated, we
dis-allow user to create two concurrent station interfaces.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-5-wright.feng@cypress.com
brcmfmac host driver makes SDIO bus sleep and stops SDIO watchdog if no
pending event or data. As a result, host driver does not poll firmware
console buffer before buffer overflow, which leads to missing firmware
logs. We should not stop SDIO watchdog if console_interval is non-zero
in debug build.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-4-wright.feng@cypress.com
When host driver retrieves mac addresses from dongle, driver copies memory
from drvr->mac to perm_addr. But at the moment, drvr->mac is all zero
array which causes permanent MAC address in wiphy is all zero as well.
To fix this, we set drvr->mac before setting perm_addr.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-3-wright.feng@cypress.com
To truncate the additional bytes, if extra bytes have been received.
Current code only have a warning and proceed without handling it.
But in one of the crash reported by DVT, these causes the
crash intermittently. So the processing is limit to the skb->len.
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-2-wright.feng@cypress.com
This is an immutable branch shared between wireless-drivers-next and
staging-next for moving wilc1000 driver out of staging to drivers/net/wireless
directory.
* Fix links to wiki;
* Some preparations for gcc-10;
* Make FW reconfiguration quieter by not using warn level;
* Some other small fixes and clean-up;
-----BEGIN PGP SIGNATURE-----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=MRiL
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2020-06-11' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First set of patches intended for v5.9
* Fix links to wiki;
* Some preparations for gcc-10;
* Make FW reconfiguration quieter by not using warn level;
* Some other small fixes and clean-up;
# gpg: Signature made Thu 11 Jun 2020 12:03:51 PM EEST using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
Currently need ptk/gtk wmi peer flags in wmi peer assoc cmd
are set based on the rsnie and wpaie of the bss from the bss list.
Since this bss list is not updated with current BSSID for AP mode,
we may not find bss from the bss list. Which results in ptk/gtk peer
flags are not set in the wmi peer assoc cmd. Due to this EAPOL frames
are going in data rates instead of management rates.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591771841-25503-1-git-send-email-vnaralas@codeaurora.org
Add support for collecting and dumping the ring backpressure
stats via debugfs. Stats are dumped only if events are
received for the specific ring.
Below command can be used to obtain these stats as part of soc dp stats.
cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats
Sample Output - When No stats available:
Backpressure Stats
==================
No Ring Backpressure stats received
Sample Output - When ring bp stats available for specific ring
Backpressure Stats
==================
Ring: REO2SW1_RING
count: 1
hp: 2
tp: 2
seen before: 4ms
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591768308-32005-3-git-send-email-srirrama@codeaurora.org
Add support for dp tx error stats which logs tx failure reasons due
to ring full condition, etc. This stats is added in soc_dp_stats
which was earlier used as soc_rx_stats so that all dp related info
are logged in same file.
Below is an example usage,
root@OpenWrt:/# cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats
SOC RX STATS:
err ring pkts: 0
Invalid RBM: 0
<snip>
SOC TX STATS:
Ring Full Failures:
ring0: 4
ring1: 3
ring2: 5
Misc Transmit Failures: 2
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591768308-32005-2-git-send-email-srirrama@codeaurora.org
spectral scan control interface is exposed through debugfs eentry.
Relayfs is used to collect the spectral data. These interfaces are
similar to ath10k spectral.
spectral debugfs interfaces are below,
echo background > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan0 > fft_samples.dump
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591688014-26441-2-git-send-email-periyasa@codeaurora.org
Add direct buffer ring (dbring) with helper API, which is used by the
spectral scan. Initialise the direct buffer ring based on the dma ring
capability, which get announced in the wmi service ready extended event.
This ring is slightly changed from data path rings. Compare to data path
ring this ring shares the hp and tp address to firmware though WMI commands.
Also the replenish buffer size is derived from firmware announcement.
driver receive indication through WMI event
WMI_PDEV_DMA_RING_BUF_RELEASE_EVENTID.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591688014-26441-1-git-send-email-periyasa@codeaurora.org
SafeSetID is capable of making allow/deny decisions for set*uid calls
on a system, and we want to add similar functionality for set*gid
calls. The work to do that is not yet complete, so probably won't make
it in for v5.8, but we are looking to get this simple patch in for
v5.8 since we have it ready. We are planning on the rest of the work
for extending the SafeSetID LSM being merged during the v5.9 merge
window.
This patch was sent to the security mailing list and there were no objections.
-----BEGIN PGP SIGNATURE-----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=I+0L
-----END PGP SIGNATURE-----
Merge tag 'LSM-add-setgid-hook-5.8-author-fix' of git://github.com/micah-morton/linux
Pull SafeSetID update from Micah Morton:
"Add additional LSM hooks for SafeSetID
SafeSetID is capable of making allow/deny decisions for set*uid calls
on a system, and we want to add similar functionality for set*gid
calls.
The work to do that is not yet complete, so probably won't make it in
for v5.8, but we are looking to get this simple patch in for v5.8
since we have it ready.
We are planning on the rest of the work for extending the SafeSetID
LSM being merged during the v5.9 merge window"
* tag 'LSM-add-setgid-hook-5.8-author-fix' of git://github.com/micah-morton/linux:
security: Add LSM hooks to set*gid syscalls
The SafeSetID LSM uses the security_task_fix_setuid hook to filter
set*uid() syscalls according to its configured security policy. In
preparation for adding analagous support in the LSM for set*gid()
syscalls, we add the requisite hook here. Tested by putting print
statements in the security_task_fix_setgid hook and seeing them get hit
during kernel boot.
Signed-off-by: Thomas Cedeno <thomascedeno@google.com>
Signed-off-by: Micah Morton <mortonm@chromium.org>
-----BEGIN PGP SIGNATURE-----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=5S0s
-----END PGP SIGNATURE-----
Merge tag 'for-5.8-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs updates from David Sterba:
"This reverts the direct io port to iomap infrastructure of btrfs
merged in the first pull request. We found problems in invalidate page
that don't seem to be fixable as regressions or without changing iomap
code that would not affect other filesystems.
There are four reverts in total, but three of them are followup
cleanups needed to revert a43a67a2d7 cleanly. The result is the
buffer head based implementation of direct io.
Reverts are not great, but under current circumstances I don't see
better options"
* tag 'for-5.8-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Revert "btrfs: switch to iomap_dio_rw() for dio"
Revert "fs: remove dio_end_io()"
Revert "btrfs: remove BTRFS_INODE_READDIO_NEED_LOCK"
Revert "btrfs: split btrfs_direct_IO to read and write part"
Tzu-En Huang