This commit changes the CMA early initialization code to use phys_addr_t
for representing physical addresses instead of unsigned long.
Without this change, among other things, dma_declare_contiguous() simply
discards any memory regions whose address is not representable as unsigned
long.
This is a problem on 32-bit PAE machines where unsigned long is 32-bit
but physical address space is larger.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
dmapool always calls dma_alloc_coherent() with GFP_ATOMIC flag,
regardless the flags provided by the caller. This causes excessive
pruning of emergency memory pools without any good reason. Additionaly,
on ARM architecture any driver which is using dmapools will sooner or
later trigger the following error:
"ERROR: 256 KiB atomic DMA coherent pool is too small!
Please increase it with coherent_pool= kernel parameter!".
Increasing the coherent pool size usually doesn't help much and only
delays such error, because all GFP_ATOMIC DMA allocations are always
served from the special, very limited memory pool.
This patch changes the dmapool code to correctly use gfp flags provided
by the dmapool caller.
Reported-by: Soeren Moch <smoch@web.de>
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Soeren Moch <smoch@web.de>
Cc: stable@vger.kernel.org
Some gate clocks have special needs which must be handled during the
disable-unused clocks sequence. These needs might be driven by software
due to the fact that we're disabling a clock outside of the normal
clk_disable path and a clk's enable_count will not be accurate. On the
other hand a specific hardware programming sequence might need to be
followed for this corner case.
This change is needed for the upcoming OMAP port to the common clock
framework. Specifically, it is undesirable to treat the disable-unused
path identically to the normal clk_disable path since other software
layers are involved. In this case OMAP's clockdomain code throws WARNs
and bails early due to the clock's enable_count being set to zero. A
custom callback mitigates this problem nicely.
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The arch/arm64/Makefile was not passing the right target to the
boot/dts/Makefile.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The REALVIEW EB board can host tiles with multiple cores thus needs
to be able to initialise SMP. There is, however, no .smp entry in
the MACHINE_START struct for REALVIEW_EB.
This patch adds the appropriate .smp entry to this struct.
Signed-off-by: Steve Capper <steve.capper@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The kernel can only be entered on HYP mode on CPUs which actually
support it, i.e. >= ARMv7. pre-v6 platform support cannot coexist
in the same kernel as support for v7 and higher, so there is no
advantage in having the HYP mode check on pre-v6 hardware.
At least one pre-v6 board is known to fail when the HYP mode check
code is present, although the exact cause remains unknown and may
be unrelated. [1]
This patch restores the old behaviour for pre-v6 platforms, whereby
the CPSR is forced directly to SVC mode with IRQs and FIQs masked.
All kernels capable of booting on v7 hardware will retain the
check, so this should not impair functionality.
[1] http://lists.arm.linux.org.uk/lurker/message/20121130.013814.19218413.en.html
([ARM] head.S change broke platform device registration?)
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The offset must be multiplied by 4 to be sure to access the correct
32bit word in the stack scratch space.
For instance, a store at scratch memory cell #1 was generating the
following:
st r4, [sp, #1]
While the correct code for this is:
st r4, [sp, #4]
To reproduce the bug (assuming your system has a NIC with the mac
address 52:54:00:12:34:56):
echo 0 > /proc/sys/net/core/bpf_jit_enable
tcpdump -ni eth0 "ether[1] + ether[2] - ether[3] * ether[4] - ether[5] \
== -0x3AA" # this will capture packets as expected
echo 1 > /proc/sys/net/core/bpf_jit_enable
tcpdump -ni eth0 "ether[1] + ether[2] - ether[3] * ether[4] - ether[5] \
== -0x3AA" # this will not.
This bug was present since the original inclusion of bpf_jit for ARM
(ddecdfce: ARM: 7259/3: net: JIT compiler for packet filters).
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
syscall_trace_exit is currently doing things back-to-front; invoking
the audit hook *after* signalling the debugger, which presents an
opportunity for the registers to be re-written by userspace in order to
bypass auditing constaints.
This patch fixes the ordering by moving the audit code first and the
tracehook code last. On the face of it, it looks like
current_thread_info()->syscall may be incorrect for the sys_exit
tracepoint, but that's actually not an issue because it will have been
set during syscall entry and cannot have changed since then.
Reported-by: Andrew Gabbasov <Andrew_Gabbasov@mentor.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Not all the architectures have readsl/writesl,
use the more portable ioread32_rep/iowrite32_rep functions instead.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Official prototype for kzalloc is:
void *kzalloc(size_t, gfp_t);
The ARM bpf_jit code was having the assumption that it was:
void *kzalloc(gfp_t, size);
This was resulting the use of some random GFP flags depending on the
size requested and some random overflows once the really needed size
was more than the value of GFP_KERNEL.
This bug was present since the original inclusion of bpf_jit for ARM
(ddecdfce: ARM: 7259/3: net: JIT compiler for packet filters).
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The matrix-keymap module is currently lacking a proper module license,
add one so we don't have this module tainting the entire kernel. This
issue has been present since commit 1932811f42 ("Input: matrix-keymap
- uninline and prepare for device tree support")
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@vger.kernel.org # v3.5+
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Netlink socket dumping had several missing verifications and checks.
In particular, address comparisons in the request byte code
interpreter could access past the end of the address in the
inet_request_sock.
Also, address family and address prefix lengths were not validated
properly at all.
This means arbitrary applications can read past the end of certain
kernel data structures.
Fixes from Neal Cardwell.
2) ip_check_defrag() operates in contexts where we're in the process
of, or about to, input the packet into the real protocols
(specifically macvlan and AF_PACKET snooping).
Unfortunately, it does a pskb_may_pull() which can modify the
backing packet data which is not legal if the SKB is shared. It
very much can be shared in this context.
Deal with the possibility that the SKB is segmented by using
skb_copy_bits().
Fix from Johannes Berg based upon a report by Eric Leblond.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
ipv4: ip_check_defrag must not modify skb before unsharing
inet_diag: validate port comparison byte code to prevent unsafe reads
inet_diag: avoid unsafe and nonsensical prefix matches in inet_diag_bc_run()
inet_diag: validate byte code to prevent oops in inet_diag_bc_run()
inet_diag: fix oops for IPv4 AF_INET6 TCP SYN-RECV state
Since the aemif driver conversion to DT along with
its movement to drivers/ folder is not yet done,
fix NAND binding documentation to have NAND specific
DT details only.
Signed-off-by: Kumar, Anil <anilkumar.v@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The description for tcp_fin_timeout should be tigher and more clear.
In addition to being tighter, we should make the spelling of the
state name consistent with what utilities report, remove the now
dated reference to 2.2 and put the default in the consistent place.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of updating stats before sending a packet,
update them after processing the packet's status.
This makes minstrel in line with minstrel_ht.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The support was already written, but the binding documentation was
lacking.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This can lead to a panic if the driver isn't ready to
handle them. Since our interrupt line is shared, we can get
an interrupt at any time (and CONFIG_DEBUG_SHIRQ checks
that even when the interrupt is being freed).
If the op_mode has gone away, we musn't call it. To avoid
this the transport disables the interrupts when the hw is
stopped and the op_mode is leaving.
If there is an event that would cause an interrupt the INTA
register is updated regardless of the enablement of the
interrupts: even if the interrupts are disabled, the INTA
will be changed, but the device won't issue an interrupt.
But the ISR can be called at any time, so we ought ignore
the value in the INTA otherwise we can call the op_mode
after it was freed.
I found this bug when the op_mode_start failed, and called
iwl_trans_stop_hw(trans, true). Then I played with the
RFKILL button, and removed the module.
While removing the module, the IRQ is freed, and the ISR is
called (CONFIG_DEBUG_SHIRQ enabled). Panic.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We know that we have issues with the fw in the reclaim path.
This is why iwl_reclaim doesn't complain too loud when it
happens since it is recoverable. Somehow, the caller of
iwl_reclaim however WARNed when it happens. This doesn't
make any sense.
When I digged into the history of that code, I discovered
that this bug occurs only when we receive a BA notification.
So move the W/A in the BA notification handling code where
it was before.
This patch addresses:
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2387
Cc: stable@vger.kernel.org
Reported-by: Florian Reitmeir <florian@reitmeir.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The WARN_ON_ONCE() check for scan_request will not correctly detect
a NULL pointer for scan_type == IWL_SCAN_NORMAL. Make it explicit
that the check only applies to normal scans.
Convert WARN_ON_ONCE to WARN_ON since priv->scan_request really _can't_
be NULL for normal scans. If it is then we should emit frequent warnings.
This smatch warning led to scrutiny of iwlagn_request_scan():
drivers/net/wireless/iwlwifi/dvm/scan.c:894 iwlagn_request_scan() error: we previously assumed 'priv->scan_request' could be null (see line 792)
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_free_txskb() needs to be used instead of dev_kfree_skb_any for
tx packets passed to the driver from mac80211
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_free_txskb() needs to be used instead of dev_kfree_skb_any for
tx packets passed to the driver from mac80211
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calibration data for devices w/o a separate
EEPROM chip can be specified via the 'eeprom_data'
field of 'ath9k_platform_data'. The 'eeprom_data'
is usually filled from board specific setup
functions. It is easy if the EEPROM data is mapped
to the memory, but it can be complicated if it is
stored elsewhere.
The patch adds support for loading of the EEPROM
data via the firmware API to avoid this limitation.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'ath9k_hw_nvram_read' function takes a
'struct ath_common *' as its first argument.
Almost each of its caller has a 'struct ath_hw *'
parameter in their argument list, and that is
dereferenced in order to get the 'struct ath_common'
pointer.
Change the first argument of 'ath9k_hw_nvram_read'
to be a 'struct ath_hw *', and remove the dereference
calls from the callers.
Also change the type of the first argument of the
ar9300_eeprom_read_{byte,word} functions.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Show the EEPROM offset of the failed read operation
in 'ath9k_hw_nvram_read'. The debug message is more
informative this way.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fill_eeprom functions are printing the same
debug message in case the 'ath9k_hw_nvram_read'
function fails. Remove the duplicated code from
fill_eeprom functions and add the ath_dbg call
directly into 'ath9k_hw_nvram_read'.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While AR_PHY_CCA_NOM_VAL_* does contain the expected internal noise floor
for a chip measured in clean air, it refers to the lowest expected reading.
Depending on the frequency, this measurement can vary by about 6db, thus
causing a higher reported channel noise and signal strength.
Factor in the 6db offset when converting internal noisefloor to channel noise.
This patch makes the reported values more accurate for all chips without
affecting NF calibration behavior.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were using wrong IRQ number so clearing wasn't working at all.
Depending on a platform this could result in a one device having two
interrupts assigned. On BCM4706 this resulted in all IRQs being broken.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: stable@vger.kernel.org
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assign the training power for PAPRD based on the chip.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a HW capability to indicate whether PAPRD is enabled
for the card, since PAPRD could be enabled in the EEPROM, but
disabled in the driver. This makes things clearer.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Retraining of PAPRD based on agc2_pwr is required for
chips other than AR9485.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Remove unneeded memset.
All the values in the PAPRD gain table are filled, so there
is no need to zero out the arrays.
* Use GFP_KERNEL in ar9003_paprd_create_curve
This is called from the PAPRD work, so the atomic variant
is not needed.
* Change return type of ar9003_paprd_setup_gain_table
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the PowerSave wrappers outside ath_paprd_activate(),
since they are already being used in ath_paprd_calibrate().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PAPRD training control registers have to be
programmed with values that depend on the chip. This patch
ensures that the correct values are chosen for the chip
in use.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various PAPRD registers are at addresses that are different
from those for the rest of the chips in the AR9003 family.
Fix them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
D-Link DWA-125/B1 is a relatively new USB Wi-Fi adapter, using a
Ralink chipset supported by the rt2800usb driver. Currently, to work
around the problem (it's missing in all present kernel versions,
up to and including 3.7.x), I had to add this to /etc/rc.local:
echo 2001 3c1e >> /sys/bus/usb/drivers/rt2800usb/new_id
After that, the device works without problems. Been using it for over
a week with no bugs in sight.
The attached patch is trivial and simply adds the new USB ID to the
list of devices handled by rt2800usb.
Signed-off-by: Maia Kozheva <sikon@ubuntu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use WARN rather than printk followed by WARN_ON(1), for conciseness.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a regression which was introduced by:
"carl9170: split up carl9170_handle_mpdu"
Previously, the ieee80211_rx_status was kept on the
stack of carl9170_handle_mpdu. Now it's passed into
the function as a pointer parameter. Hence, the old
memcpy call needs to be fixed.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This device can be found on some embedded devices connected to a
Broadcom SoC like the BCM4718.
I tested this with my Netgear WNDR3400 v1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vitaly Andrianov