Upcoming firmware introduces command interface revision 3, which
changes the way port capabilities are queried and set. Update the
driver to handle both the new and old command interfaces by adding a
new MLX4_FLAG_OLD_PORT_CMDS that it is set after querying the firmware
interface revision and then using the correct interface based on the
setting of the flag.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
New ConnectX firmware introduces FW command interface revision 2,
which requires that for each QP, a chunk of send queue entries (the
"headroom") is kept marked as invalid, so that the HCA doesn't get
confused if it prefetches entries that haven't been posted yet. Add
code to the driver to do this, and also update the user ABI so that
userspace can request that the prefetcher be turned off for userspace
QPs (we just leave the prefetcher on for all kernel QPs).
Unfortunately, marking send queue entries this way is confuses older
firmware, so we change the driver to allow only FW command interface
revisions 2. This means that users will have to update their firmware
to work with the new driver, but the firmware is changing quickly and
the old firmware has lots of other bugs anyway, so this shouldn't be too
big a deal.
Based on a patch from Jack Morgenstein <jackm@dev.mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a dMPT entry has the PA flag (direct physical address) set, then
the (unused) MTT base address field has to be set to 0.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
HCA firmware with incompatible changes to the FW commmand interface is
coming soon. Add a check of the interface revision during
initialization and bail out if the firmware advertises a revision that
the driver doesn't know about. This will avoid strange failures later
if the driver goes on using the wrong interface revision.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We need to pass the same dev_id to free_irq() and request_irq(). When
using MSI-X, the MLX4_EQ_CATAS interrupt uses a different dev_id from
the other interrupts.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We may call mlx4_dispatch_event() before mlx4_register_device() is
called for a device, because for example a catastrophic error happens
immediately after we enable interrupts. Therefore priv->ctx_list and
priv->ctx_lock need to be initialized earlier.
This bug was actually exposed by the MSI-X bug that returned IRQ numbers
to drivers in reverse order, so that the first FW command
interrupt looked to mlx4 like a catastrophic error.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The reserved6 field should be 64 bits, not just 16 bits. Without
this, the structure does not match the hardware layout on 32-bit
architectures: the db_rec_addr field ends up at offset 52 instead of
offset 56. The bug slipped by because the alignment of __be64 members
ends up putting it in the right place on x86-64.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set last allocated object to the object after the one just allocated
before ORing in the extra top bits. Also handle the case where this
wraps around.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't overrun fname[] array when decoding device flags.
This was spotted by the Coverity checker (CID 1642).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB/cm: Optimize stale connection detection
IB/mthca: Set cleaned CQEs back to HW ownership when cleaning CQ
IB/mthca: Fix posting >255 recv WRs for Tavor
RDMA/cma: Add check to validate that cm_id is bound to a device
RDMA/cma: Fix synchronization with device removal in cma_iw_handler
RDMA/cma: Simplify device removal handling code
IB/ehca: Disable scaling code by default, bump version number
IB/ehca: Beautify sysfs attribute code and fix compiler warnings
IB/ehca: Remove _irqsave, move #ifdef
IB/ehca: Fix AQP0/1 QP number
IB/ehca: Correctly set GRH mask bit in ehca_modify_qp()
IB/ehca: Serialize hypervisor calls in ehca_register_mr()
IB/ipath: Shadow the gpio_mask register
IB/mlx4: Fix uninitialized spinlock for 32-bit archs
mlx4_core: Remove unused doorbell_lock
net: Trivial MLX4_DEBUG dependency fix.
Add an InfiniBand driver for Mellanox ConnectX adapters. Because
these adapters can also be used as ethernet NICs and Fibre Channel
HBAs, the driver is split into two modules:
mlx4_core: Handles low-level things like device initialization and
processing firmware commands. Also controls resource allocation
so that the InfiniBand, ethernet and FC functions can share a
device without stepping on each other.
mlx4_ib: Handles InfiniBand-specific things; plugs into the
InfiniBand midlayer.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Roland Dreier