Commit Graph

5097 Commits

Author SHA1 Message Date
John W. Linville 96da266e77 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem 2014-03-31 15:22:17 -04:00
Chun-Yeow Yeoh 52e346d1e7 ath10k: add extra pdev stats on 10.1 firmware
As pointed out by Michal Kazior, add extra pdev stats
for 10.1 firmware.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 17:00:00 +02:00
Ben Greear 23c3aae4a0 ath10k: add the Rx rate in FW stats
FW stats does provide the Rx rate information. Add this.
Tested with firmware 10x firmware.

Increase buffer size so more peers can be shown.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 16:58:50 +02:00
Ben Greear db9cdda650 ath10k: fix getting stats from firmware
Tested on 10.x firmware, and others report it at least
makes older firmware no more broken than it already was.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 16:56:14 +02:00
Bartosz Markowski 34d714e0cf ath10k: update wal_dbg_tx_stats structure with missing parameter.
The filed has been missing (missmatched with FW ABI)
since 999.999.0.629 firmware release.

It's very imporatant to keep these structs up to date with FW,
due to the arithmetic we use while read the fw_stats.

Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 16:53:48 +02:00
Michal Kazior df5e85250a ath10k: deinit copy engine before resetting
Since copy engine allocation has been revised the
ath10k_pci_ce_deinit() now simply zeroes copy
engine registers. It's probably a good idea to do
that before reseting for a more graceful device
reset.

Before ath10k_pci_ce_deinit() freed copy engine
ringbuffer memory so it was required to call it
after resetting. Otherwise it was possible for
device to access unmapped/freed copy engine
ringbuffer memory.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 14:32:18 +02:00
Michal Kazior 25d0dbcbd5 ath10k: split ce initialization and allocation
Definitions by which copy engine structure are
allocated do not change so it doesn't make much
sense to re-create those structures each time
device is booted (e.g. due to firmware recovery).

This should decrease chance of memory allocation
failures.

While at it remove per_transfer_context pointer
indirection. The array has been trailing the copy
engine ringbuffer structure anyway. This also
saves pointer size worth of bytes for each copy
engine ringbuffer.

Reported-By: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 14:32:10 +02:00
Michal Kazior 68c03249f3 ath10k: convert pci_alloc_consistent() to dma_alloc_coherent()
This allows to use GFP_KERNEL allocation. This
should decrease chance of allocation failure, e.g.
during firmware recovery.

Reported-By: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 14:32:01 +02:00
Kalle Valo c508671dd5 ath10k: print chip id during boot
This makes it easier to debug what kind of board is used.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 14:22:53 +02:00
Kalle Valo 78a9cb4ce7 ath10k: add module parameter values to the pci info print
Hopefully this makes it easier to debug problems in the future.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 14:22:45 +02:00
Kalle Valo 50f87a674f ath10k: improve pci debug messages
To make it easier to debug pci problems improve the log messages in pci.c. Also
change some debug messages to warning messages to more easily catch problems.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 14:22:37 +02:00
Kalle Valo b39712ce29 ath10k: delete ar_pci->fw_indicator_address
It always contains the same constant, no need to have a separate variable for it.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 14:22:30 +02:00
Kalle Valo 929417cf0e ath10k: advertise only firmware API 2 files
We do not really support older firmware API 1 anymore, so better remove
MODULE_FIRMWARE() declarations for them and only list for API 2 files.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 14:22:21 +02:00
Kalle Valo e42c1fbd13 ath10k: fix name of target_ps module parameter
The parameter name was ath10k_target_ps, but actually it should be just
target_ps. Module parameter names should not use the ath10k_ prefix.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 14:22:04 +02:00
Kalle Valo 35098463a8 ath10k: add module parameter to disable cold reset
As cold reset is not reliable with CUS223 boards, make it possible
to disable cold reset entirely and only use warm reset. This makes it also
easier to debug warm reset problems.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 14:21:50 +02:00
Kalle Valo 0399eca800 ath10k: cleanup ath10k_pci_wait_for_target_init()
ath10k_pci_wait_for_target_init() did really follow the style used elsewhere in
ath10k. Use ath10k_pci_read/write() wrappers, simplify the while loop and
improve warning messages.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 14:21:41 +02:00
Ben Greear 36a8f413a3 ath10k: add otp and firmware boot error messages
If OTP or firmware fails to load properly, print out some
extra info in the kernel logs.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 09:43:26 +02:00
Ben Greear 53c0228456 ath10k: better firmware loading error messages
Let user know the name of the board file if it is not
found, and make it easier to determine the firmware
api being used.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 09:43:02 +02:00
Kalle Valo be6546fcc2 ath10k: unify warning messages in mac.c
Currently there are different styles used for warning messages, unify them to
look similar. The style basically is:

1) start with a verb (if possible)

2) lower case letters

3) use plain english as much as possible

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 09:41:03 +02:00
Joe Perches 8986992de4 carl9170: Remove casts of pointer to same type
Casting a pointer to a pointer of the same type is pointless,
so remove these unnecessary casts.

Done via coccinelle script:

$ cat typecast_2.cocci
@@
type T;
T *foo;
@@

-	(T *)foo
+	foo

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-27 14:20:05 -04:00
David S. Miller 04f58c8854 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	Documentation/devicetree/bindings/net/micrel-ks8851.txt
	net/core/netpoll.c

The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.

In micrel-ks8851.txt we simply have overlapping changes.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-25 20:29:20 -04:00
Janusz Dziedzic 2289188c27 ath10k: fix rssi and rate reporting
RSSI and RATES fields are valid only when START_VALID
bit is set. So, in current implementation we have to
remember/caclulate them when START_VALID and report the same
when only END_VALID is set.
Currently during heavy traffic we could have:
- 10 packets with START_VALID - correct RSSI and RATES
- 10 packets with END_VALID
- 10 packets with START_VALID - correct RSSI and RATES
- 10 packets with END_VALID
...
Next using monitor interface we will see:
- 10 packets with correct rssi/rates
- 10 packets with rssi=-95/rate=6Mbps

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-25 14:15:27 +02:00
Janusz Dziedzic 6df92a3d02 ath10k: introduce rx_status htt template
Introduce rx_status htt template instead of
stack version, as a preparation for fix
rssi and rates reporting.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-25 14:15:19 +02:00
Janusz Dziedzic 85f6d7cfbb ath10k: finally kill htt_rx_info
Struct htt_rx_info is not needed anymore while
we will use ieee80211_rx_status structure as
a template.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-25 14:12:46 +02:00
Janusz Dziedzic 78433f9653 ath10k: improve way we play with attention flags
Remove almost the same code, and do only once
__le32_to_cpu() conversion.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-25 14:12:37 +02:00
Janusz Dziedzic d84dd60f2c ath10k: return error when ath10k_htt_rx_amsdu_pop() fail
Return error when rx_amsdu_pop() will fail.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-25 14:12:29 +02:00
Janusz Dziedzic 87326c97b8 ath10k: kill not needed fields from htt_rx_info
Kill rates, tsf, fcs_err, mic_err, amsdu_more, encrypt_type, signal
from htt_rx_info and setup this directly in ieee80211_rx_status.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-25 14:12:18 +02:00
Janusz Dziedzic 36653f050b ath10k: setup rx channel per ppdu
Setup band and frequency in ieee80211_rx_status
only once - for ppdu.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-25 14:12:07 +02:00
Janusz Dziedzic 8f739db0c4 ath10k: introduce ieee80211_rx_status to htt_rx_info
Will be used as a template, and final storage for
rx_status.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-25 14:11:58 +02:00
Janusz Dziedzic cfadd9ba9a ath10k: rename process_rx_rates to ath10k_htt_rx_h_rates
No functional changes.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-25 14:11:41 +02:00
Janusz Dziedzic 73539b406c ath10k: move rx related functions to htt_rx.c
No functional changes.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-25 14:11:23 +02:00
Chun-Yeow Yeoh cf0fd56235 ath10k: fix the peer mac address in getting stats
Using the macro to convert the MAC address from WMI word
format to char array has lead to the wrong peer mac
address printed out while retrieving the peer stats from
FW. Fix this.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Reviewed-By: Michał Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-24 10:28:44 +02:00
Marek Puzyniak 821af6ae26 ath10k: update regulatory domain settings for 10.x firmware
Regulatory domain settings for firmware 10.x has more options
than main firmware, so handle regulatory domain setup separately
for both supported firmwares. Fill in additional dfs domain
parameter according to current regulatory.
This patch does not solve any known bug. Not handled parameter
for firmware 10.x was found during code review.

Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-24 10:25:46 +02:00
Marek Puzyniak 8c65699274 ath10k: add soft/hard firmware crash option to simulate_fw_crash
Command WMI_FORCE_FW_HANG_CMDID is not supported in firmware 10.1.
In order to have firmware crash simulation functionality also
in firmware 10.1 driver can force firmware crash by performing not allowed
operation. Driver can deliberately crash firmware when setting vdev param for
vdev id out of range.  This patch introduces two keywords to simulate_fw_crash:

'soft' which will cause firmware crash that is recoverable
       by warm firmware reset but supported only in main firmware.
'hard' which will cause firmware crash recoverable by cold
       firmware reset, this option works for both firmwares.

Commands to trigger firmware soft/hard crash:

echo 'soft' > /sys/kernel/debug/ieee80211/phyX/ath10k/simulate_fw_crash
echo 'hard' > /sys/kernel/debug/ieee80211/phyX/ath10k/simulate_fw_crash

kvalo: remove '\n' before checking the command and simplify how buf is null
terminated

Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-24 10:23:50 +02:00
John W. Linville 49c0ca17ee Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem 2014-03-21 14:02:04 -04:00
Janusz Dziedzic e8dc1a968d ath10k: Fill per-ppdu info in rx_info only once
Don't fill this for each msdu, while this is the
same.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-21 17:42:22 +02:00
Janusz Dziedzic 2acc4eb2d0 ath10k: add ath10k_htt_rx_amsdu_allowed function
Introduce ath10k_htt_rx_amsdu_allowed() function, that
group code for checking if skip amsdu packets.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-21 17:41:15 +02:00
Kalle Valo 7f06ea1e79 ath10k: check otp.bin result
When we execute otp.bin in the target check that the result it returns doesn't
contain an error. This is to make sure that we don't accidentally use invalid
calibration data.

While at it, remove the useless label in the function and add few debug messages.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-21 17:41:03 +02:00
Kalle Valo d6d4a58dcb ath10k: separate result parameter in ath10k_bmi_execute()
It's just cleaner to have separate argument for the parameter and result. Also
fix returned error value if response length is invalid.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-21 17:40:53 +02:00
Vladimir Kondratiev 097638a08a wil6210: fix race between disconnect and Tx NAPI
When disconnecting some CID, corresponded Tx vring get released. During vring
release, all descriptors get freed. It is possible that Tx NAPI working on the same
vring simultaneously. If it happens, descriptor may be double freed.

To protect from the race above, make sure NAPI won't process the same vring.
Introduce 'enabled' flag in the struct vring_tx_data. Proceed with Tx NAPI only if
'enabled' flag set. Prior to Tx vring release, clear this flag and make sure NAPI
get synchronized.

NAPI enablement status protected by wil->mutex, add protection where it was
missing and check for it.

During reset, disconnect all peers first, then proceed with the Rx vring. It allows for
the disconnect flow to observe proper 'wil->status' and correctly notify cfg80211 about
connection status change

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:19 -04:00
Vladimir Kondratiev 260e695196 wil6210: add memory barriers for the reset flow
make sure reset flow executed in order

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:19 -04:00
Vladimir Kondratiev d28bcc3026 wil6210: target reset flow update
Use 'real' indication for hardware state.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:19 -04:00
Vladimir Kondratiev b5998e6a3d wil6210: use GRO
GRO is easy to enable when already using NAPI framework,
and it improves CPU utilisation. Enable it by default.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:18 -04:00
Vladimir Kondratiev 9c3bde56b7 wil6210: serialize fw_recovery and start_ap
These methods can change device state, serialize with others
similar ones like up/down

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:18 -04:00
Vladimir Kondratiev 4cd9e8377f wil6210: fix secondary connect
when STA receiving connect() when already connected,
it should return error

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:18 -04:00
Vladimir Kondratiev ed6f9dc62f wil6210: fw error recovery
upon fw error interrupt - in STA mode, disconnect/cancel scan and
then reset FW/HW
added module param - no_fw_recovery which is false by default

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:18 -04:00
Vladimir Kondratiev 0fef1818d0 wil6210: Fix kernel oops in reset flow
wil_reset() removes vring's
At the same time NAPI may be active performing Rx/Tx completion.
If this happens, Rx/Tx polling functions going to access already removed vrings

Make sure NAPI is idle and won't be started prior to vring removal.
For this, track NAPI enabled state

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:18 -04:00
Vladimir Kondratiev 8bf6adb988 wil6210: fix memory leak in the AP flow
When switching between STA and AP modes, memory allocated for Rx vring leaks
This is because start_ap() allocates Rx vring but stop_ap() do not free it.
Logically, Rx vring is not valid (HW can't use it anymore), so free it in reset()
Also, check double init for Rx vring and bail out with -EINVAL

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:18 -04:00
Vladimir Kondratiev fa4a18e73b wil6210: reduce printing
Convert 2 often printed messages to dynamic ones

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:17 -04:00
Vladimir Kondratiev 972072aa79 wil6210: reset on power good
Configure hardware to perform full reset on "power good". This mean,
reset HW on system boot. This improves card stability.
By default this is off.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:17 -04:00
Vladimir Kondratiev 1712399121 wil6210: sort HW registers definitions
Put all registers in order for easier navigation;
fix naming to reflect hardware cluster

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:17 -04:00
Vladimir Kondratiev f4b5a8032d wil6210: fix for HW bug in interrupt setup logic
Hardware bug triggered by the MSI init while INTx asserted for some reason.
De-assert INTx prior to MSI set-up

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:17 -04:00
Vladimir Kondratiev 98a65b59f8 wil6210: report reset time
Useful to detect hardware problems

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:17 -04:00
Vladimir Kondratiev aa27deaabf wil6210: reduce dmesg pollution after FW crash
When FW crashes, dmesg get polluted with the "FW not ready"
error message. Print it only once per FW lifecycle

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:17 -04:00
Vladimir Kondratiev 36b10a7239 wil6210: update target reset to support new HW
Support for new chip revision. Revision read from the
internal register, PCIE config's "revision id" register
do not indicate HW version properly

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:17 -04:00
Vladimir Kondratiev 2232abd59a wil6210: generalize tx desc mapping
Introduce enum to describe mapping type; allow 'none' in addition to
'single' and 'page'; this is preparation for GSO

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:16 -04:00
Vladimir Kondratiev c236658f14 wil6210: add scatter-gather support
When setting fragmented skb for Tx, assign skb to the last descriptor
and set number of fragments in the 1-st one
On Tx complete, HW sets "DU" bit in Tx descriptor only for the last
descriptor; so search for it using number of fragments field.
Middle descriptors may have "DU" bit not set by the hardware.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:16 -04:00
Vladimir Kondratiev e83eb2fcae wil6210: enable scan while connected
New firmware do support scan while connected. Enable it.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:16 -04:00
Vladimir Kondratiev e58c9f7043 wil6210: Block data till "data port open" reported
When connection established, as reported by WMI_CONNECT_EVENTID,
4-way handshaking required for the secure connection is not done
yet. It is indicated by another WMI event. Wait for it and only then
allow data traffic. In case of non-secure connection, FW reports
"data port open" immediately after connection.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:16 -04:00
Vladimir Kondratiev a70abea5f5 wil6210: Helpers to deal with 'cidxtid' fields
Encode/decode helpers

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:16 -04:00
Sujith Manoharan d65b1278e3 ath9k: Fix temperature compensation
The registers for temperature compensation need to
be programmed only for active chains. Use the TX chainmask
to make sure that this is done properly for QCA953x.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:16 -04:00
Sujith Manoharan c90d4f7bc5 ath9k: Disable AR_INTR_SYNC_HOST1_FATAL for QCA953x
Along with AR9340 and AR955x, this is also needed for
the QCA953x SoC.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:15 -04:00
Sujith Manoharan c08148bb75 ath9k: Add QCA953x WMAC platform support
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:44:15 -04:00
Oleksij Rempel 5f667642f4 ath9k_htc: move DEFAULT_SWBA_RESPONSE check to ath9k_htc_beacon_init
... to remove some more dups.

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:09 -04:00
Oleksij Rempel 4b2d841f5b ath9k_htc: use ath9k_cmn_beacon_config_ap
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:08 -04:00
Oleksij Rempel 6a77dd33fc ath9k: remove unused ath9k_get_next_tbtt
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:08 -04:00
Oleksij Rempel fa7b52fadb ath9k: move ath9k_beacon_config_ap common
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:08 -04:00
Oleksij Rempel 12f53c308e ath9k_htc: use ath9k_cmn_beacon_config_adhoc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:08 -04:00
Oleksij Rempel f7197924d5 ath9k_htc: use ath9k_htc_beacon_init in ath9k_htc_beacon_config_adhoc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:08 -04:00
Oleksij Rempel 4a4495a5fd ath9k_htc: use ath9k_htc_beacon_init in ath9k_htc_beacon_config_ap
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:08 -04:00
Oleksij Rempel 7f5c4c8320 ath9k_htc: add ath9k_htc_beacon_init (but not use it)
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:07 -04:00
Oleksij Rempel 4c9a1f3260 ath9k: move ath9k_beacon_config_adhoc to common
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:07 -04:00
Oleksij Rempel f84224402b ath9k_htc: use ath9k_cmn_beacon_config_sta
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:07 -04:00
Oleksij Rempel cbbdf2ae2d ath9k: move ath9k_beacon_config_sta to common-beacon
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:07 -04:00
Oleksij Rempel a2030b9dbc ath9k-common: add nexttbtt and intval to ath_beacon_config
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:07 -04:00
Oleksij Rempel c7303263a0 ath9k|ath9k_htc: move IEEE80211_MS_TO_TU to common
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:07 -04:00
Oleksij Rempel df728780d2 ath9k: remove unused beacon_qi
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:06 -04:00
Oleksij Rempel cc24c86f7c ath9k_htc: sync beacon slot code with ath9k
we will need it for common-beacon

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:06 -04:00
Oleksij Rempel ed51fe314f ath9k: remove unused bc_tstamp
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:06 -04:00
Oleksij Rempel c35ccb38d4 ath9k_htc: add ATH_OP_PRIM_STA_VIF
we will need it to make common-beacon code work.

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:06 -04:00
Oleksij Rempel 92c3f7ef2c ath9k_htc: use common->op_flags
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:06 -04:00
Oleksij Rempel eefa01ddd5 ath9k: move sc_flags to ath_common
we will need it for ath9k_htc, may be other drivers too

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:06 -04:00
Oleksij Rempel 88a4f56ef0 ath9k_htc: use ath_beacon_conf.enable_beacon
to reduce difference between ath9k and ath9k_htc

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:05 -04:00
Oleksij Rempel a099874ed9 ath9k_htc: move beaconq to struct htc_beacon
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:05 -04:00
Oleksij Rempel 3c4816d9a3 ath9k_htc: use common ath_beacon_config
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:05 -04:00
Oleksij Rempel fd0ab79335 ath9k: move struct ath_beacon_config to common
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17 13:13:05 -04:00
Joe Perches 1b5c8d60d2 ath9k: Convert uses of __constant_<foo> to <foo>
The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-14 14:49:16 -04:00
John Greene b499abdc76 ath5k: add missing dma_map_error call
Trivial patch to address this trace. Now calls dma_mapping_error and
return -ENOSPC if a problem found.

WARNING: at lib/dma-debug.c:933 check_unmap+0x47b/0x960()
Hardware name: Aspire 5515
ath5k 0000:02:00.0: DMA-API: device driver failed to check map
error[device address=0x00000000874fcd42] [size=45 bytes] [mapped as
single]
Modules linked in: bnep bluetooth ebtable_filter ebtables
ip6table_filter ip6_tables be2iscsi iscsi_boot_sysfs bnx2i cnic uio
cxgb4i cxgb4 cxgb3i cxgb3 mdio libcxgbi ib_iser rdma_cm ib_addr iw_cm
ib_cm ib_sa ib_mad ib_core iscsi_tcp libiscsi_tcp libiscsi
scsi_transport_iscsi arc4 snd_hda_codec_realtek snd_hda_intel
snd_hda_codec snd_hwdep snd_seq snd_seq_device ath5k ath snd_pcm
sparse_keymap snd_page_alloc mac80211 snd_timer sp5100_tco snd edac_core
k8temp soundcore edac_mce_amd i2c_piix4 cfg80211 rfkill shpchp vhost_net
tun macvtap macvlan kvm_amd kvm uinput dm_crypt ata_generic pata_acpi
radeon i2c_algo_bit pata_atiixp drm_kms_helper ttm drm r8169 mii
i2c_core wmi video sunrpc
Pid: 820, comm: firewalld Not tainted 3.9.0-0.rc3.git1.4.fc19.x86_64 #1
Call Trace:
 <IRQ>  [<ffffffff81068df0>] warn_slowpath_common+0x70/0xa0
 [<ffffffff81068e6c>] warn_slowpath_fmt+0x4c/0x50
 [<ffffffff8137ebeb>] check_unmap+0x47b/0x960
 [<ffffffff81021cf5>] ? native_sched_clock+0x15/0x80
 [<ffffffff81021d69>] ? sched_clock+0x9/0x10
 [<ffffffff8137f12f>] debug_dma_unmap_page+0x5f/0x70
 [<ffffffffa048fa07>] ath5k_tasklet_tx+0x157/0x3f0 [ath5k]
 [<ffffffff810acc0d>] ? sched_clock_local+0x1d/0x80
 [<ffffffff81072aa6>] ? tasklet_action+0x56/0x210
 [<ffffffff81072ae7>] tasklet_action+0x97/0x210
 [<ffffffff8107343f>] __do_softirq+0xff/0x400
 [<ffffffff81073905>] irq_exit+0xb5/0xc0
 [<ffffffff81728916>] do_IRQ+0x56/0xc0
 [<ffffffff8171dc32>] common_interrupt+0x72/0x72
 <EOI>  [<ffffffff811f1f81>] ? dput+0x111/0x310
 [<ffffffff811f1ea7>] ? dput+0x37/0x310
 [<ffffffff811e75e8>] link_path_walk+0x528/0x910
 [<ffffffff811ea624>] path_openat+0x94/0x530
 [<ffffffff811eb148>] do_filp_open+0x38/0x80
 [<ffffffff811e1dda>] open_exec+0x4a/0x130
 [<ffffffff81238be3>] load_elf_binary+0x7f3/0x18e0
 [<ffffffff81021d69>] ? sched_clock+0x9/0x10
 [<ffffffff810acc0d>] ? sched_clock_local+0x1d/0x80
 [<ffffffff810acd98>] ? sched_clock_cpu+0xa8/0x100
 [<ffffffff810d515d>] ? trace_hardirqs_off+0xd/0x10
 [<ffffffff810acedf>] ? local_clock+0x5f/0x70
 [<ffffffff810d5dbf>] ? lock_release_holdtime.part.28+0xf/0x190
 [<ffffffff812383f0>] ? elf_core_dump+0x1980/0x1980
 [<ffffffff811e1151>] search_binary_handler+0x1a1/0x4f0
 [<ffffffff811e1017>] ? search_binary_handler+0x67/0x4f0
 [<ffffffff811e28fc>] do_execve_common.isra.26+0x64c/0x710
 [<ffffffff811e23c2>] ? do_execve_common.isra.26+0x112/0x710
 [<ffffffff811e2cc6>] sys_execve+0x36/0x50
 [<ffffffff81727249>] stub_execve+0x69/0xa0

Signed-off-by: John Greene <jogreene@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-14 14:49:16 -04:00
Felix Fietkau 9301ca90b6 ath9k_hw: set ANI firstep as absolute values instead of relative
On older chips, the INI value differ in similar ways as cycpwr_thr1, so
convert it to absolute values as well.

Since the ANI algorithm is different here compared to the old
implementation (fewer steps, controlled at a different point in time),
it makes sense to use values similar to what would be applied for newer
chips, just without relying on INI defaults.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-14 14:49:15 -04:00
Felix Fietkau 28327fd096 ath9k_hw: set ANI cycpwr_thr1 as absolute values instead of relative
The table was copied from the ANI implementation of AR9300. It assumes
that the INI values contain a baseline value that is usable as reference
from which to increase/decrease based on the noise immunity value.

On older chips, the differences are bigger and especially AR5008/AR9001
are configured to much more sensitive values than what is useful.

Improve ANI behavior by reverting to the absolute values used in the
previous implementation (expressed as a simple formula instead of the
old table).

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-14 14:49:15 -04:00
Felix Fietkau afdc05f09d ath9k_hw: remove ANI function restrictions for AP mode
The primary purpose of this piece of code was to selectively disable
OFDM weak signal detection. The checks for this are elsewhere, and an
earlier commit relaxed the restrictions for older chips, which are more
sensitive to interference.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-14 14:49:15 -04:00
Felix Fietkau abee4c8414 ath9k: clean up and enhance ANI debugfs file
Unify scnprintf calls and include the current OFDM/CCK immunity level.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-14 14:49:14 -04:00
Felix Fietkau 3b3e0efb5c ath9k: fix ready time of the multicast buffer queue
qi->tqi_readyTime is written directly to registers that expect
microseconds as unit instead of TU.
When setting the CABQ ready time, cur_conf->beacon_interval is in TU, so
convert it to microseconds before passing it to ath9k_hw.

This should hopefully fix some Tx DMA issues with buffered multicast
frames in AP mode.

Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-14 14:49:14 -04:00
John W. Linville 1698aca040 Merge branch 'for-linville' of git://github.com/kvalo/ath 2014-03-14 14:25:53 -04:00
Helmut Schaa 5998be8797 ath9k: Fix sequence number assignment for non-data frames
Since commit 558ff225de (ath9k: fix
ps-poll responses under a-mpdu sessions) non-data frames would have
gotten a sequence number from a TIDs sequence counter instead of
using the global sequence counter.

This can lead to instable connections.

To fix this only select the correct TID if we are processing a
data frame. Furthermore, prevent non-data frames to get a sequence
number from a TID sequence counter by adding a check to
ath_tx_setup_buffer.

Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-13 14:57:26 -04:00
Felix Fietkau 105ff411c9 ath9k_hw: fix unreachable code in baseband hang detection code
The commit "ath9k: reduce baseband hang detection false positive rate"
added a delay in the loop checking the baseband state, however it was
unreachable due to previous 'continue' statements.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-13 14:57:26 -04:00
John W. Linville 42775a34d2 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
	drivers/net/wireless/ath/ath9k/recv.c
2014-03-13 14:21:43 -04:00
Kalle Valo b5a637881f ath6kl: update Kconfig descriptions
The help text were either out of date, too small or didn't exist at all. Also
move cfg80211 dependency to ath6kl_core module as it has all the calls to
cfg80211.

Fixes checkpatch warning:

WARNING: please write a paragraph that describes the config symbol fully

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-13 07:47:26 +02:00
Kalle Valo 996bc93231 ath6kl: remove unnecessary line continuations
Fixes checkpatch warning:

WARNING: Avoid unnecessary line continuations

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-13 07:47:14 +02:00
Kalle Valo c28d5559e9 ath6kl: remove spaces before semicolon
Fixes checkpatch warning:

CHECK: space prohibited before semicolon

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-13 07:47:05 +02:00
Kalle Valo a5d8f9dfcf ath6kl: use braces on both arms of if statement
Fixes checkpatch warning:

CHECK: braces {} should be used on all arms of this statement

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-13 07:46:56 +02:00
Kalle Valo 3629fa1438 ath6kl: fix blank lines before and after braces
Fixes checkpatch warnings:

CHECK: Blank lines aren't necessary after an open brace '{'
CHECK: Blank lines aren't necessary before a close brace '}'

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-13 07:46:31 +02:00
Kalle Valo 31b9cc9a87 ath6kl: fix struct hif_scatter_req list handling
Jason noticed that with Yocto GCC 4.8.1 ath6kl crashes with this iperf command:

iperf -c $TARGET_IP -i 5 -t 50 -w 1M

The crash was:

Unable to handle kernel paging request at virtual address 1a480000
pgd = 80004000
[1a480000] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
Modules linked in: ath6kl_sdio ath6kl_core [last unloaded: ath6kl_core]
CPU: 0 PID: 1953 Comm: kworker/u4:0 Not tainted 3.10.9-1.0.0_alpha+dbf364b #1
Workqueue: ath6kl ath6kl_sdio_write_async_work [ath6kl_sdio]
task: dcc9a680 ti: dc9ae000 task.ti: dc9ae000
PC is at v7_dma_clean_range+0x20/0x38
LR is at dma_cache_maint_page+0x50/0x54
pc : [<8001a6f8>]    lr : [<800170fc>]    psr: 20000093
sp : dc9afcf8  ip : 8001a748  fp : 00000004
r10: 00000000  r9 : 00000001  r8 : 00000000
r7 : 00000001  r6 : 00000000  r5 : 80cb7000  r4 : 03f9a480
r3 : 0000001f  r2 : 00000020  r1 : 1a480000  r0 : 1a480000
Flags: nzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c53c7d  Table: 6cc5004a  DAC: 00000015
Process kworker/u4:0 (pid: 1953, stack limit = 0xdc9ae238)
Stack: (0xdc9afcf8 to 0xdc9b0000)
fce0:                                                       80c9b29c 00000000
fd00: 00000000 80017134 8001a748 dc302ac0 00000000 00000000 dc454a00 80c12ed8
fd20: dc115410 80017238 00000000 dc454a10 00000001 80017588 00000001 00000000
fd40: 00000000 dc302ac0 dc9afe38 dc9afe68 00000004 80c12ed8 00000000 dc454a00
fd60: 00000004 80436f88 00000000 00000000 00000600 0000ffff 0000000c 80c113c4
fd80: 80c9b29c 00000001 00000004 dc115470 60000013 dc302ac0 dc46e000 dc302800
fda0: dc9afe10 dc302b78 60000013 dc302ac0 dc46e000 00000035 dc46e5b0 80438c90
fdc0: dc9afe10 dc302800 dc302800 dc9afe68 dc9afe38 80424cb4 00000005 dc9afe10
fde0: dc9afe20 80424de8 dc9afe10 dc302800 dc46e910 80424e90 dc473c00 dc454f00
fe00: 000001b5 7f619d64 dcc7c830 00000000 00000000 dc9afe38 dc9afe68 00000000
fe20: 00000000 00000000 dc9afe28 dc9afe28 80424d80 00000000 00000035 9cac0034
fe40: 00000000 00000000 00000000 00000000 000001b5 00000000 00000000 00000000
fe60: dc9afe68 dc9afe10 3b9aca00 00000000 00000080 00000034 00000000 00000100
fe80: 00000000 00000000 dc9afe10 00000004 dc454a00 00000000 dc46e010 dc46e96c
fea0: dc46e000 dc46e964 00200200 00100100 dc46e910 7f619ec0 00000600 80c0e770
fec0: dc15a900 dcc7c838 00000000 dc46e954 8042d434 dcc44680 dc46e954 dc004400
fee0: dc454500 00000000 00000000 dc9ae038 dc004400 8003c450 dcc44680 dc004414
ff00: dc46e954 dc454500 00000001 dcc44680 dc004414 dcc44698 dc9ae000 dc9ae030
ff20: 00000001 dc9ae000 dc004400 8003d158 8003d020 00000000 00000000 80c53941
ff40: dc9aff64 dcb71ea0 00000000 dcc44680 8003d020 00000000 00000000 00000000
ff60: 00000000 80042480 00000000 00000000 000000f8 dcc44680 00000000 00000000
ff80: dc9aff80 dc9aff80 00000000 00000000 dc9aff90 dc9aff90 dc9affac dcb71ea0
ffa0: 800423cc 00000000 00000000 8000e018 00000000 00000000 00000000 00000000
ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<8001a6f8>] (v7_dma_clean_range+0x20/0x38) from [<800170fc>] (dma_cache_maint_page+0x50/0x54)
[<800170fc>] (dma_cache_maint_page+0x50/0x54) from [<80017134>] (__dma_page_cpu_to_dev+0x34/0x9c)
[<80017134>] (__dma_page_cpu_to_dev+0x34/0x9c) from [<80017238>] (arm_dma_map_page+0x64/0x68)
[<80017238>] (arm_dma_map_page+0x64/0x68) from [<80017588>] (arm_dma_map_sg+0x7c/0xf4)
[<80017588>] (arm_dma_map_sg+0x7c/0xf4) from [<80436f88>] (sdhci_send_command+0x894/0xe00)
[<80436f88>] (sdhci_send_command+0x894/0xe00) from [<80438c90>] (sdhci_request+0xc0/0x1ec)
[<80438c90>] (sdhci_request+0xc0/0x1ec) from [<80424cb4>] (mmc_start_request+0xb8/0xd4)
[<80424cb4>] (mmc_start_request+0xb8/0xd4) from [<80424de8>] (__mmc_start_req+0x60/0x84)
[<80424de8>] (__mmc_start_req+0x60/0x84) from [<80424e90>] (mmc_wait_for_req+0x10/0x20)
[<80424e90>] (mmc_wait_for_req+0x10/0x20) from [<7f619d64>] (ath6kl_sdio_scat_rw.isra.10+0x1dc/0x240 [ath6kl_sdio])
[<7f619d64>] (ath6kl_sdio_scat_rw.isra.10+0x1dc/0x240 [ath6kl_sdio]) from [<7f619ec0>] (ath6kl_sdio_write_async_work+0x5c/0x104 [ath6kl_sdio])
[<7f619ec0>] (ath6kl_sdio_write_async_work+0x5c/0x104 [ath6kl_sdio]) from [<8003c450>] (process_one_work+0x10c/0x370)
[<8003c450>] (process_one_work+0x10c/0x370) from [<8003d158>] (worker_thread+0x138/0x3fc)
[<8003d158>] (worker_thread+0x138/0x3fc) from [<80042480>] (kthread+0xb4/0xb8)
[<80042480>] (kthread+0xb4/0xb8) from [<8000e018>] (ret_from_fork+0x14/0x3c)
Code: e1a02312 e2423001 e1c00003 f57ff04f (ee070f3a)
---[ end trace 0c038f0b8e0b67a3 ]---
Kernel panic - not syncing: Fatal exception

Jason's analysis:

  "The GCC 4.8.1 compiler will not do the for-loop till scat_entries, instead,
   it only run one round loop. This may be caused by that the GCC 4.8.1 thought
   that the scat_list only have one item and then no need to do full iteration,
   but this is simply wrong by looking at the assebly code. This will cause the sg
   buffer not get set when scat_entries > 1 and thus lead to kernel panic.

   Note: This issue not observed with GCC 4.7.2, only found on the GCC 4.8.1)"

Fix this by using the normal [0] style for defining unknown number of list
entries following the struct. This also fixes corruption with scat_q_depth, which
was mistankely added to the end of struct and overwritten if there were more
than item in the scat list.

Reported-by: Jason Liu <r64343@freescale.com>
Tested-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-13 07:20:00 +02:00
Marek Kwaczynski e81bd10482 ath10k: add recalc RTS/CTS protection method
Add recalculation of RTS/CTS protection when one or more legacy
stations are connected to ath10k. In this case enable RTS/CTS
protection and set sw retry profile are needed in the FW.
Without this change legacy station is starved and has very low
throughput.

Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-13 07:14:28 +02:00
Chun-Yeow Yeoh 44d6fa90a8 ath10k: allow the supported rate change by reassociate peer
IBSS mode requires the changing of supported rate. Do this
by reassociate the peer. The investigation shows that if move
from legacy to HT, the rate control won't work after changing
the supported rate. But once changing the supported rate to HT,
user can assign the TxRate in HT mode.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-11 12:18:39 +02:00
Marek Puzyniak 70dd77b4c5 ath10k: do not overwrite max_antenna_gain
Seems like we have an old bug, where we incidently overwrites
the max_antenna_gain we pass to firmware, with zero value.

End of all we are artifically reducing the output power.

This patch removes the excessive assignment on max_antenna_gain,
which is being provided by regulatory domain, and consequently
improves the tx power.

Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-07 10:14:10 +02:00
Ben Greear bfa353689a ath10k: support msdu chaining
Consolidate the list of msdu skbs into the msdu-head skb, delete the
rest of the skbs, pass the msdu-head skb on up the stack as normal.

Tested with high-speed TCP and UDP traffic on modified firmware that
supports raw-rx.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-07 10:11:21 +02:00
David S. Miller 67ddc87f16 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/wireless/ath/ath9k/recv.c
	drivers/net/wireless/mwifiex/pcie.c
	net/ipv6/sit.c

The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.

The two wireless conflicts were overlapping changes.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-05 20:32:02 -05:00
John W. Linville f3b6a488a6 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
	drivers/net/wireless/ath/ath9k/recv.c
	drivers/net/wireless/mwifiex/pcie.c
2014-03-04 13:05:12 -05:00
Vladimir Kondratiev c14c5d99a4 wil6210: fix smatch warning in wil_cfg80211_get_station()
Smatch suggests to propagate error code from wil_find_cid(), and, indeed,
it is a good idea.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-03 15:35:56 -05:00
Vladimir Kondratiev af31cb5a57 wil6210: fix buffer overflow in wil_txdesc_debugfs_show()
Wrong index comparison logic, found by smatch:

drivers/net/wireless/ath/wil6210/debugfs.c:402 wil_txdesc_debugfs_show() warn: buffer overflow 'wil->vring_tx' 24 <= 24

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-03 15:35:56 -05:00
Felix Fietkau f554724521 ath9k_hw: tweak noise immunity thresholds for older chipsets
Older chipsets are more sensitive to high PHY error counts, and the
current noise immunity thresholds were based on tests run at QCA with
newer chipsets.

This patch brings back the values from the old ANI implementation for
old chipsets, and it also disables weak signal detection on an earlier
noise immunity level, to improve overall radio stability on affected
devices.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-03 15:35:55 -05:00
Felix Fietkau 6241226f68 ath9k_hw: toggle weak signal detection in AP mode on older chipsets
The commit 80b4205b "ath9k: Fix OFDM weak signal detection for AP mode"
prevented weak signal detection changes from taking effect in AP mode on
all chipsets, claiming it is "not allowed".

The main reason for not disabling weak signal detection in AP mode is
that typically beacon RSSI is used to track whether it is needed to
boost range, and this is unavailable in AP mode for obvious reasons.

The problem with not disabling weak signal detection is that older
chipsets are very sensitive to high PHY error counts. When faced with
heavy noise, this can lead to an excessive amount of "Failed to stop
TX DMA" errors in the field.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-03 15:35:55 -05:00
Sylvain Roger Rieunier 727b662c2b ath9k: fix invalid max frame length
According to 802.11n-2012 standard in paragraph PPDU Fromat(20.3.2) HT-mixed
format  Hearder PPDU contains : L_STF, L_LTF, L_SIG, HT_SIG, HT_STF, HT_LTF
they are symbols in the preamble, there are in time unit(us) that's for why
it can't be computed in bytes

Signed-off-by: Sylvain ROGER RIEUNIER <sylvain.roger.rieunier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-03 15:35:55 -05:00
Ben Greear 69244e5656 ath10k: add vdev-id, return code to error codes
When using multiple vdevs (stations, aps, etc), it is
nice to be able to associate log messages with specific
interfaces.  So, add vdev-id to most logging messages.
Add return code as well, where it was missing.

kvalo: unify some of the messages to follow the same style

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-03 17:38:46 +02:00
Vladimir Kondratiev 0bbc4adebd wil6210: do not reorder groupcast Rx
Groupcast frames are not subject for BACK reordering because they are not
ACK'ed and one can't request re-transmitt

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:38 -05:00
Vladimir Kondratiev 4d55a0a1a8 wil6210: single station disconnect
implement del_station() method in the struct cfg80211_ops
It allows to disconnect single peer from the AP

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:37 -05:00
Vladimir Kondratiev 108d1eb612 wil6210: use ether_addr_equal
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:37 -05:00
Vladimir Kondratiev b8b33a3a67 wil6210: Provide signal strength indication
When notifying about Rx mgmt (ex: during scan), extract
signal strength reported by the hardware.
signal is not MBM, it is arbitrary units 0..100

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:36 -05:00
Vladimir Kondratiev 93ae6d49e2 wil6210: Fill vring2cid_tid table early
Need to fill translation table before calling WMI with WMI_VRING_CFG_CMDID
since firmware may generate events during this call; and events need translation
table filled to be properly dispatched

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:35 -05:00
Vladimir Kondratiev 91886b0b7d wil6210: disconnect only requested peer
Disconnect event reported by the FW, should lead to disconnection
of only requested peer. Find for the appropriate CID and disconnect
only it

For AP-like interface, notify cfg80211 with del_sta(),
for the client type interface, disconnect and turn link off.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:34 -05:00
Vladimir Kondratiev c8b78b5f0f wil6210: per-connection statistics
Calculate statistics per connection, report with "iw station dump"

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:34 -05:00
Vladimir Kondratiev ef28afdb1c wil6210: dump_station initial support
Rx stats is not calculated per STA - just give some number

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:33 -05:00
Vladimir Kondratiev 7b05b0ab89 wil6210: fix BACK status processing
When FW notifies about BACK status change, it provides ring ID.
Process BA status for requested connection only. As for now, FW
don't report Rx BACK status, it reports Tx one instead.
As per current algorithm used in the firmware, imply Rx BACK
state is in sync with Tx one

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:32 -05:00
Vladimir Kondratiev fb3cac5726 wil6210: broadcast Tx
Hardware do not support "real" broadcast on the air.
Use method similar to the Directed Multicast Service (DMS) as
described in the 10.23.15.2 "DMS procedures"

This service copies frame and delivers unicast for each associated peer

Do the following: send original frame to 1-st Tx vring, and send copies
to all other active vrings.

As currently hardware/firmware don't support A-MSDU, convert broadcast
frame to unicast instead of wrapping it in A-MSDU

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:31 -05:00
Vladimir Kondratiev 9a1773847d wil6210: Find free vring for Tx
There are 24 possible Tx vrings; when doind multiple connections, more then
one vring has to be used. Search for free one and select it.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:31 -05:00
Vladimir Kondratiev b4490f423c wil6210: Block ACK
When running multiple connections, hardware can't do BACK reordering
and it should be done on the host.

Model after mac80211's implementation. Drop RCU for now;
to be re-added when BACK will be stabilized

BACK handshaking is not implemented yet in the hardware,
pretend it was done to support the way FW operating

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:30 -05:00
Vladimir Kondratiev 3df2cd3618 wil6210: multiple connect - initial support
Enable multiple (up to 8 - HW/FW limitation) simultaneous connections.
Each connection has its own CID (connection ID) that describes chip's
beam-forming entity. Tx Vring should refer to correct CID for frame to reach
its destination.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:29 -05:00
Vladimir Kondratiev 59f7c0a957 wil6210: [DEBUG] Improve Vring printing
Print '_' for the 'idle' descriptors - this makes vring representation more visible.
Also, for the Tx side, differentiate descriptors having associated skb's - print ones
with skb as 'H' and without as 'h'. Good to represent scattered frames.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:28 -05:00
Vladimir Kondratiev 3a85543e9f wil6210: [DEBUG] allow to query Rx and all Tx VRING descriptors
Expand debug capabilities to query all Tx/Rx descriptors. Usefull to analyse
various hardware/software stall situations. Printed is whole descriptor content
and the frame itself.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:28 -05:00
Vladimir Kondratiev 1647f12f1b wil6210: Tx management frame
Implement management frame passing. In order to receive frame on the other
side, remain_on_channel() should be implemented as well

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:27 -05:00
Oleksij Rempel 2259ba38a5 ath9k_htc: add function ath9k_regwrite_multi
... to remove duplicate code

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:25 -05:00
Oleksij Rempel 527492eefc ath9k_htc: remove unused variable sleepduration
sleepduration is always = intval.

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:25 -05:00
Oleksij Rempel 7fbdaa2a27 ath9k: remove unused listen_interval and sleepduration.
this variable never changed.

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:24 -05:00
Oleksij Rempel 6da2f4ad9d ath9k_htc: use ath9k_cmn_reload_chainmask
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:16 -05:00
Oleksij Rempel b57ba3b2f7 ath9k: move ath9k_reload_chainmask_settings to common
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:16 -05:00
Oleksij Rempel 91884fad85 ath9k-common: set maxstream=1 for ar9271
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:15 -05:00
Oleksij Rempel e9fb588867 ath9k_htc: use ath9k_cmn_setup_ht_cap
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:14 -05:00
Oleksij Rempel b60d105242 ath9k: move setup_ht_cap to common-init
and rename it to ath9k_cmn_setup_ht_cap

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:13 -05:00
Oleksij Rempel 31f023a1cb ath9k_htc: use ath9k_cmn_init_channels_rates
and ath_common sbands.

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:13 -05:00
Oleksij Rempel 13f71050c1 ath9k: move ath9k_init_channels_rates to common-init
and rename it to ath9k_cmn_init_channels_rates.
sbands are move to ath_common as well.

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-28 14:33:12 -05:00
Michal Kazior 8d60ee87a7 ath10k: minimize coherent dma accesses
It doesn't make much sense to calculate the ring
size fill count because it already is memoized in
a separate variable.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-28 12:00:41 +02:00
Michal Kazior 2f5280da40 ath10k: remove pci completion list
One of the premises was to guarantee serialized
completion handling for upper layers
(HTC/WMI/HTT). Since quite some time now it is no
longer necessary.

The other premise was to batch up tx/rx
completions to take advantage of hot caches.
However frame tx/rx completion indications come in
on a single pipe already so they are already
batched up. More meaningful batching is done in
HTT itself.

This means PCI completion is no longer necessary
to keep around. It just wastes memory, cycles and
SLOC.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-28 12:00:30 +02:00
Michal Kazior 45967089d2 ath10k: reduce htt tx/rx spinlock overhead
It is inefficient to grab irqsave spinlocks for
skb lists for each queue/dequeue action.

Using rx_ring.lock and tx_lock allows to use less
heavy bh spinlock functions and moving locking
upwards allows to toggle spinlocks less often.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-28 11:59:55 +02:00
Michal Kazior 6c5151a9ff ath10k: batch htt tx/rx completions
HTT Rx endpoint processes both frame rx
indications and frame tx completion indications.

Those completions typically come in batches and
may be mixed so it makes sense to defer processing
hoping to get a bunch of them and take advantage
of hot caches.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-28 11:59:25 +02:00
Michal Kazior a16942e630 ath10k: bypass htc for htt tx path
Going through full htc tx path for htt tx is a
waste of resources. By skipping it it's possible
to easily submit scatter-gather to the pci hif for
reduced host cpu load and improved performance.

The new approach uses dma pool to store the
following metadata for each tx request:
 * msdu fragment list
 * htc header
 * htt tx command

The htt tx command contains a msdu prefetch.
Instead of copying it original mapped msdu address
is used to submit a second scatter-gather item to
hif to make a complete htt tx command.

The htt tx command itself hands over dma mapped
pointers to msdus and completion of the command
itself doesn't mean the frame has been sent and
can be unmapped/freed. This is why htc tx
completion is skipped for htt tx as all tx related
resources are freed upon htt tx completion
indication event (which also implicitly means htt
tx command itself was completed).

Since now each htt tx request effectively consists
of 2 copy engine items CE_HTT_H2T_MSG_SRC_NENTRIES
is updated to allow maximum of
TARGET_10X_NUM_MSDU_DESC msdus being queued. This
keeps the tx path resource management simple.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-28 11:59:17 +02:00
Michal Kazior 726346fc71 ath10k: replace send_head() with tx_sg()
PCI is capable of handling scatter-gather lists.
This can be used to avoid copying memory.

Change the name of the callback while at to
reflect its purpose.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-28 11:59:06 +02:00
Michal Kazior 7676a88876 ath10k: remove is_aborted from skb_cb
The flag wasn't used anymore. No need to keep it.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-28 11:58:53 +02:00
Michal Kazior 767d34fc67 ath10k: remove DMA mapping wrappers
There's no real benefit from using them. DMA-API
already provides debugging. Some skbuffs are
already mapped directly with DMA-API since wrapper
arguments were insufficient and extending them
would be pointless.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-28 11:58:38 +02:00
Janusz Dziedzic a80ddb003a ath10k: skip management frames in HTT path
After we pass frames with INV_PEER to upper layer in commit 716ae53c56
("ath10k: pass frames with invalid peer status to upper layer") we could pass
some management frames (in case INVALID_PEER and MGMT_CTRL) twice to upper
layer, once via WMI and once via HTT. Next we could handle assoc request twice.
This patch remove such regression.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-27 18:42:08 +02:00
Janusz Dziedzic 9f81f72556 ath10k: bitrate_mask add force_sgi support
Add force SGI support.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-27 18:40:37 +02:00
Janusz Dziedzic 2f0f112111 ath10k: enable spectrum management support
Indicate spectrum management support in hardware
flags, while we already handle power set
(IEEE80211_CONF_CHANGE_POWER) in the ath10k driver.
This enable 802.11h support for station mode.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-27 18:39:05 +02:00
Chun-Yeow Yeoh e72698f8a9 ath10k: set the mactime of ieee80211_rx_status
Retrieve the mactime of ieee80211_rx_status based on received
data frame. The value is obtained from the htt_rx_indication_ppdu
structure and only available in 32-bit.

kvalo: white space fixes

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-27 18:37:05 +02:00
Michal Kazior 76f900244f ath10k: fix sta_rc_update for non-ap iftype
The arsta structure wasn't initialized for
non-ap interfaces. This should fix related
warnings/crashes.

Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-26 18:39:12 +02:00
Michal Kazior d960c369c8 ath10k: fix 4addr rx
The nwifi header is padded to 4 bytes. This wasn't
a problem until one tried to (at least) rx 4addr
frames.

This finally allows managed iface to be used in a
bridge.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-26 18:37:38 +02:00
Ben Greear 9ba4c787aa ath10k: add more details to some debug messages
Makes it easier to determine why some failures
happened.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-26 18:36:01 +02:00
Chun-Yeow Yeoh 26ebbccfb7 ath10k: implement drv_get_tsf for ibss merging
Implement the get TSF by simply returning 0 so that IBSS
merging is happening. Otherwise, IBSS nodes that have similar
SSID naming won't merge. This is simply fooling the mac80211
that the TSF in the received beacon is higher than the local TSF.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-26 18:30:57 +02:00
Felix Fietkau b7b146c9c9 ath9k: fix invalid descriptor discarding
Only set sc->rx.discard_next to rx_stats->rs_more when actually
discarding the current descriptor.

Also, fix a detection of broken descriptors:
First the code checks if the current descriptor is not done.
Then it checks if the next descriptor is done.
Add a check that afterwards checks the first descriptor again, because
it might have been completed in the mean time.

This fixes a regression introduced in
commit 723e711356
"ath9k: fix handling of broken descriptors"

Cc: stable@vger.kernel.org
Reported-by: Marco André Dinis <marcoandredinis@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-25 14:54:11 -05:00
Felix Fietkau d31a36a6d8 ath9k: reduce baseband hang detection false positive rate
Check if the baseband state remains stable, and add a small delay
between register reads.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-25 14:54:11 -05:00
Felix Fietkau ef1b4141d0 ath5k: set SURVEY_INFO_IN_USE on get_survey
Only one channel is returned - the one currently being used.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-24 15:38:39 -05:00
Felix Fietkau affad456f2 ath9k: make some hardware reset log messages debug-only
On some chips, baseband watchdog hangs are more common than others, and
the driver has support for handling them.
Interrupts even after a watchdog hang are also quite common, so there's
not much point in spamming the user's logfiles.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-24 15:38:39 -05:00
Felix Fietkau cd6cfd7311 ath9k: do not set half/quarter channel flags in AR_PHY_MODE
5/10 MHz channel bandwidth is configured via the PLL clock, instead of
the AR_PHY_MODE register. Using that register is AR93xx specific, and
makes the mode incompatible with earlier chipsets.

In some early versions, these flags were apparently applied at the wrong
point in time and thus did not cause connectivity issues, however now
they are causing problems, as pointed out in this OpenWrt ticket:

https://dev.openwrt.org/ticket/14916

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-24 15:38:38 -05:00
Joe Perches 2120ac9674 ath9k: Use static const
Trivially reduces text size too.

$ size drivers/net/wireless/ath/ath9k/debug.o*
   text	   data	    bss	    dec	    hex	filename
  34436	   2528	   5128	  42092	   a46c	drivers/net/wireless/ath/ath9k/debug.o.new
  34464	   2528	   5128	  42120	   a488	drivers/net/wireless/ath/ath9k/debug.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-24 15:38:38 -05:00
Felix Fietkau 443626e5a9 ath9k: list more reset causes in debugfs
Number of MAC hangs and stuck beacons were missing

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-24 15:38:37 -05:00
Jouni Malinen 7b4f663ee6 ath9k: Enable U-APSD AP mode support
mac80211 handles the actual operations, so ath9k can just indicate
support for this. Based on initial tests, this combination seems to
work fine.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-24 15:21:54 -05:00
John W. Linville 9e4b4269ec Merge branch 'for-linville' of git://github.com/kvalo/ath 2014-02-24 15:02:36 -05:00
Felix Fietkau 558ff225de ath9k: fix ps-poll responses under a-mpdu sessions
When passing tx frames to the U-APSD queue for powersave poll responses,
the ath_atx_tid pointer needs to be passed to ath_tx_setup_buffer for
proper sequence number accounting.

This fixes high latency and connection stability issues with ath9k
running as AP and a few kinds of mobile phones as client, when PS-Poll
is heavily used

Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-24 14:55:27 -05:00
Sujith Manoharan b3050248c1 ath9k: Fix ETSI compliance for AR9462 2.0
The minimum CCA power threshold values have to be adjusted
for existing cards to be in compliance with new regulations.
Newer cards will make use of the values obtained from EEPROM,
support for this was added earlier. To make sure that cards
that are already in use and don't have proper values in EEPROM,
do not violate regulations, use the initvals instead.

Cc: stable@vger.kernel.org
Reported-by: Jeang Daniel <dyjeong@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-20 15:53:20 -05:00
Stanislaw Gruszka 21f8aaee0c ath9k: protect tid->sched check
We check tid->sched without a lock taken on ath_tx_aggr_sleep(). That
is race condition which can result of doing list_del(&tid->list) twice
(second time with poisoned list node) and cause crash like shown below:

[424271.637220] BUG: unable to handle kernel paging request at 00100104
[424271.637328] IP: [<f90fc072>] ath_tx_aggr_sleep+0x62/0xe0 [ath9k]
...
[424271.639953] Call Trace:
[424271.639998]  [<f90f6900>] ? ath9k_get_survey+0x110/0x110 [ath9k]
[424271.640083]  [<f90f6942>] ath9k_sta_notify+0x42/0x50 [ath9k]
[424271.640177]  [<f809cfef>] sta_ps_start+0x8f/0x1c0 [mac80211]
[424271.640258]  [<c10f730e>] ? free_compound_page+0x2e/0x40
[424271.640346]  [<f809e915>] ieee80211_rx_handlers+0x9d5/0x2340 [mac80211]
[424271.640437]  [<c112f048>] ? kmem_cache_free+0x1d8/0x1f0
[424271.640510]  [<c1345a84>] ? kfree_skbmem+0x34/0x90
[424271.640578]  [<c10fc23c>] ? put_page+0x2c/0x40
[424271.640640]  [<c1345a84>] ? kfree_skbmem+0x34/0x90
[424271.640706]  [<c1345a84>] ? kfree_skbmem+0x34/0x90
[424271.640787]  [<f809dde3>] ? ieee80211_rx_handlers_result+0x73/0x1d0 [mac80211]
[424271.640897]  [<f80a07a0>] ieee80211_prepare_and_rx_handle+0x520/0xad0 [mac80211]
[424271.641009]  [<f809e22d>] ? ieee80211_rx_handlers+0x2ed/0x2340 [mac80211]
[424271.641104]  [<c13846ce>] ? ip_output+0x7e/0xd0
[424271.641182]  [<f80a1057>] ieee80211_rx+0x307/0x7c0 [mac80211]
[424271.641266]  [<f90fa6ee>] ath_rx_tasklet+0x88e/0xf70 [ath9k]
[424271.641358]  [<f80a0f2c>] ? ieee80211_rx+0x1dc/0x7c0 [mac80211]
[424271.641445]  [<f90f82db>] ath9k_tasklet+0xcb/0x130 [ath9k]

Bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=70551

Reported-and-tested-by: Max Sydorenko <maxim.stargazer@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-20 15:53:20 -05:00
John W. Linville 88daf80dcc Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem 2014-02-20 15:02:02 -05:00
David S. Miller 1e8d6421cf Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/bonding/bond_3ad.h
	drivers/net/bonding/bond_main.c

Two minor conflicts in bonding, both of which were overlapping
changes.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-19 01:24:22 -05:00
Alexander Gordeev b4b39061da wil6210: Use pci_enable_msi_range() instead of pci_enable_msi_block()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.

Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: wil6210@qca.qualcomm.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-18 15:33:34 -05:00
Michal Kazior 9797febc4c ath10k: implement sta_rc_update()
This allows dynamic changes of bandwidth/nss/smps,
e.g. via ht/vht operation mode change
notification.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-15 08:49:02 +02:00
Michal Kazior 90046f509d ath10k: fix SMPS support
Firmware ignores SMPS flags in peer assoc command.

For SMPS to work it is necessary to set peer
parameter after peer assoc command so that tx
chainmask is setup properly.

This should fix packet loss and improve throughput
with stations that have SMPS enabled upon
association.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-15 08:47:36 +02:00
Kalle Valo 75459e3338 ath10k: release conf_mutex if vdev_start() fails
I modified Michal's commit c930f744bd ("ath10k: implement channel switching") to return
when vdev_start() fails, but forgot to release conf_mutex.

Found by coccinelle:

>> drivers/net/wireless/ath/ath10k/mac.c:2745:5-11: preceding lock on line 2663

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-14 13:20:45 +02:00
Kalle Valo ef8c00174a ath: remove camel case from struct reg_dmn_pair_mapping
Fixes a checkpatch warning in ath10k:

drivers/net/wireless/ath/ath10k/mac.c:1636: WARNING: Avoid CamelCase: <regpair->regDmnEnum>

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-14 13:20:32 +02:00
Kalle Valo 2e05f01bd1 ath10k: fix alignment in ath10k_dbg()
Fix a checkpatch warning:

drivers/net/wireless/ath/ath10k/debug.h:95: CHECK: Alignment should match open parenthesis

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-14 13:19:55 +02:00
Pontus Fuchs 908628db14 wcn36xx: Update dtim period before starting BSS
The dtim period sent to FW was 0 because the dtim period
was never set. This caused an incorrect dtim count to be sent in
beacons.

Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-13 15:20:18 -05:00
Pontus Fuchs 82cad2a0b0 wcn36xx: Track dpu signature per sta
This fixes problems seen with multiple softap clients and reconnecting
softap clients.

Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-13 15:20:17 -05:00
Pontus Fuchs 2ba0b46175 wcn36xx: Rename wcn36xx_vif.ucast_dpu_signature to self_ucast_dpu_sign
This is more line with the names of the other members

Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-13 15:20:17 -05:00
Pontus Fuchs f2ed5d2499 wcn36xx: Add support for 3680
3680 has a few registers on other addresses.

Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-13 15:20:17 -05:00
Pontus Fuchs 2be6636a96 wcn36xx: Print FW capabilities
After fw caps exchange, print the FW's capabilities.

Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-13 15:20:17 -05:00
Pontus Fuchs 4bda7faf61 wcn36xx: Cache nv to avoid request_firmware on resume path
If wowlan if off mac80211 will stop / start the driver on suspend /
resume. This causes problems on resume since request_firmware is called
from start. Fix this by caching the nv.

Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-13 15:20:17 -05:00
Pontus Fuchs 546c505bdc wcn36xx: Wait longer for SMD commands to complete
On some wcnss firmwares the start command can take up to 300ms to
complete. Currently there is a 200ms timeout for SMD command to
complete which causes the start to fail.

Increase the timeout to 500ms. Also improve debug information
regarding SMD command completion time.

Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-13 15:20:17 -05:00
Pontus Fuchs c951da4615 wcn36xx: Improve feature caps exchange
* Response format is not in the canonical format.
  wcn36xx_smd_rsp_status_check cannot be used.

* Save the FW caps in wcn36xx struct for later use.

Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-13 15:20:17 -05:00
Pontus Fuchs 08762322c3 wcn36xx: Fix copy paste error hal_exit_bmps -> hal_keep_alive
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-13 15:20:17 -05:00
Dan Carpenter 4a0732d1f9 ath5k: shifting the wrong variable for AR5K_AR5210
In the original code we shift "AR5K_PHY(256) >> 28" which is zero but
the intent was to shift the return value of ath5k_hw_reg_read() like we
do a couple lines later.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-13 14:58:12 -05:00
John W. Linville 0e028ab0fb Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless 2014-02-13 14:43:02 -05:00
Alexander Gordeev 5ad6867cb5 ath10k: Use pci_enable_msi_range()
As result deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.

Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-13 18:04:26 +02:00
Alexander Gordeev bb8b621ac3 ath10k: Disable MSI in case IRQ configuration is unknown
In case IRQ configuration is unknown possibly enabled MSIs
are left enabled in ath10k_pci_deinit_irq(). This update
fixes the described misbehaviour.

Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-13 18:04:00 +02:00
Alexander Gordeev bdcb2c9e2f ath10k: Get rid of superfluous call to pci_disable_msi()
The documentation states that pci_enable_msi_block() returns the number of
requests 'could have been allocated', not 'could allocate'. IOW, MSIs are *not*
enabled if a positive value returned.

kvalo: add commit log based on Alexander's email

Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-13 18:01:36 +02:00
Janusz Dziedzic 716ae53c56 ath10k: pass frames with invalid peer status to upper layer
Pass frames with invalid peer status to upper layer.
Next mac80211 will validate frames and drop if required.
This is required to detect spurious frames and pass
this info to user mode (detect CLASS2 CLASS3 frames from
nonauthenticated/nonassociated stations).

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-13 17:53:10 +02:00
Bartosz Markowski fd71f80737 ath10k: AP: handle HT station which does not have HT RX MCS
This is a workaround for HT-enabled STAs which break the spec
and have no HT capabilities RX mask (no HT RX MCS map).

As per spec, in section 20.3.5 Modulation and coding scheme (MCS),
MCS 0 through 7 are mandatory in 20MHz with 800 ns GI at all STAs.

Firmware asserts if such situation occurs.

Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-13 17:46:06 +02:00
Marek Puzyniak 00f5482bcd ath10k: suspend hardware before reset
In case of warm reset target need to be suspended.
Suspend function is extented to handle both cases
with disabling interrupts and without disabling interrupts.
Warm target reset requires suspend with all interrupts
disabled.

This patch depends on
ath10k: fix device initialization routine

Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-13 17:24:17 +02:00
Marek Puzyniak 9042e17df8 ath10k: refactor suspend/resume functions
Suspend/resume callbacks are not protected by configuration mutex
so adding such protection. Also in order to simplify implemetation
of suspend function wait queue is replaced by completion.

Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-13 17:24:01 +02:00
Michal Kazior fc36e3ffcd ath10k: fix device initialization routine
Hardware CUS232 version 2 has some issues with cold
reset that lead to Data Bus Errors or system hangs
in some cases. It's safer to use warm reset when
possible as it shouldn't trigger the
aforementioned issues.

Prefer warm reset over cold reset. However since
warm reset doesn't work after FW crash make sure to
fallback to cold reset when booting up the HW.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-13 16:55:01 +02:00
Marek Kwaczynski 36786024df ath10k: Set proper nss value for the peer
It was found during testing the nss calculation does not
cover all corner cases. Station could request eq. only MCS8
and MCS9 (nss=2 specific). Next num_rates=2 so the driver
sets nss=(max((2+7)/8, 1))=1. Which is wrong. The in-driver
calculation was introduced prior (commit ddcc347b70
mac80211: fix rx_nss calculation for drivers with hw rc).
Since it's fixed, use mac80211 provided value from now.
End user will experience lower throuhputs than expected
if the nss is wrongly calculated.

Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-13 16:48:46 +02:00
Bartosz Markowski 7c61385454 ath10k: remove excessive rx msdu len check
This throw a lot of pointless warnings in case of DFS (radar
detection) and PHYERR events from firmware, when firmware may
actually insert more data, than we assume.

Besides of being noisy this debug does not protect or check
anything usefull currently. It was introduced long time ago
while debugging aggregations. So just removing it.

Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-13 16:47:45 +02:00
Ben Greear 75fb2f94f2 ath10k: better tx/rx debugging
Make it easier to grep for htt rx errors.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-13 16:32:51 +02:00
Ben Greear c6b56b03a7 ath10k: add more debugging for receive errors
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-13 16:31:58 +02:00