The patch below fixes a warning message Im seeing with gcc 4.6.0
CC [M] drivers/net/wireless/hostap/hostap_main.o
drivers/net/wireless/hostap/hostap_main.c: In function 'hostap_set_multicast_list_queue':
drivers/net/wireless/hostap/hostap_main.c:744:27: warning: variable 'iface' set but not used
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use an irq spinlock to hold off the IRQ handler until
enough early card init is complete such that the handler
can run without faulting.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cleanup patch.
Use new __packed annotation in drivers/net/
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
switch and while statements don't need semicolons at end of statement
[ Fixup minor conflicts with recent wimax merge... -DaveM ]
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop cast on the result of kmalloc and similar functions.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
@@
- (T *)
(\(kmalloc\|kzalloc\|kcalloc\|kmem_cache_alloc\|kmem_cache_zalloc\|
kmem_cache_alloc_node\|kmalloc_node\|kzalloc_node\)(...))
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dev_node_t was only used to transport some minor/major numbers
from the PCMCIA device drivers to deprecated userspace helpers.
However, only a few drivers made use of it, and the userspace
helpers are deprecated anyways. Therefore, get rid of dev_node_t .
As a first step, remove any usage of dev_node_t from drivers which
only wrote to this typedef/struct, but did not make use of it.
CC: linux-bluetooth@vger.kernel.org
CC: Harald Welte <laforge@gnumonks.org>
CC: linux-mtd@lists.infradead.org
CC: linux-wireless@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: alsa-devel@alsa-project.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Instead of the old pcmcia_request_irq() interface, drivers may now
choose between:
- calling request_irq/free_irq directly. Use the IRQ from *p_dev->irq.
- use pcmcia_request_irq(p_dev, handler_t); the PCMCIA core will
clean up automatically on calls to pcmcia_disable_device() or
device ejection.
- drivers still not capable of IRQF_SHARED (or not telling us so) may
use the deprecated pcmcia_request_exclusive_irq() for the time
being; they might receive a shared IRQ nonetheless.
CC: linux-bluetooth@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: linux-usb@vger.kernel.org
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
...and use it in hostap_cs and orinoco_cs.
Another PCMCIA device with Intersil Prism chipset has been reported:
Socket 0:
product info: "Gigabyte", "GN-WLM01_P25L_ADAPTER", "ISL37300P", "Eval-RevA"
manfid: 0x02e0, 0x1011
function: 6 (network)
As it's the case with some other Prism based devices, the third ID
string contains a design name that should be sufficient to identify the
card as having Intersil Prism chipset and thus compatible with both
orinoco_cs and hostap_cs.
Introduce PCMCIA_DEVICE_PROD_ID3 that matches the third ID string only.
Use it in orinoco_cs and hostap_cs to match cards with the third ID
string indicating Prism chipset. Remove corresponding entries that use
PCMCIA_DEVICE_PROD_ID123.
Reported-by: Ozzy <ozzymud@gmail.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BugLink: https://bugs.launchpad.net/ubuntu/+bug/254837
Spurious shared interrupts or early probing interrupts can cause the
hostap interrupt handler to oops before the driver has fully configured
the IO base port addresses. In some cases the oops can be because
the hardware shares an interrupt line, on other cases it is due to a
race condition between probing for the hardware and configuring
the IO base port. The latter occurs because the probing is required to
determin the hardware port address which is only determined when the probe
can interrupt the hardware (catch 22).
This patch catches this pre-configured condition to avoid the oops.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Acked-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most of the irq_req_t typedef'd struct can be re-worked quite
easily:
(1) IRQInfo2 was unused in any case, so drop it.
(2) IRQInfo1 was used write-only, so drop it.
(3) Instance (private data to be passed to the IRQ handler):
Most PCMCIA drivers using pcmcia_request_irq() to actually
register an IRQ handler set the "dev_id" to the same pointer
as the "priv" pointer in struct pcmcia_device. Modify the two
exceptions (ipwireless, ibmtr_cs) to also work this waym and
set the IRQ handler's "dev_id" to p_dev->priv unconditionally.
(4) Handler is to be of type irq_handler_t.
(5) Handler != NULL already tells whether an IRQ handler is present.
Therefore, we do not need the IRQ_HANDLER_PRESENT flag in
irq_req_t.Attributes.
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: Jaroslav Kysela <perex@perex.cz>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Karsten Keil <isdn@linux-pingi.de>
for the Bluetooth parts: Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Convert PCMCIA drivers to use the dynamic debug infrastructure, instead of
requiring manual settings of PCMCIA_DEBUG.
Also, remove all usages of the CS_CHECK macro and replace them with proper
Linux style calling and return value checking. The extra error reporting may
be dropped, as the PCMCIA core already complains about any (non-driver-author)
errors.
CC: linux-wireless@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
A few PCMCIA network drivers can make use of values provided by the pcmcia
core, instead of tedious, independent CIS parsing.
xirc32ps_cs.c: manf_id
hostap_cs.c: multifunction count
b43/pcmcia.c: ConfigBase address and "Present"
smc91c92_cs.c: By default, mhz_setup() can use VERS_1 as it is stored
in struct pcmcia_device. Only some cards require workarounds, such as
reading out VERS_1 twice.
CC: David S. Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
With the WLAN_PRE80211 drivers moved to drivers/staging, this
distinction becomes unnecessary.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Refactor wext to
* split out iwpriv handling
* split out iwspy handling
* split out procfs support
* allow cfg80211 to have wireless extensions compat code
w/o CONFIG_WIRELESS_EXT
After this, drivers need to
- select WIRELESS_EXT - for wext support
- select WEXT_PRIV - for iwpriv support
- select WEXT_SPY - for iwspy support
except cfg80211 -- which gets new hooks in wext-core.c
and can then get wext handlers without CONFIG_WIRELESS_EXT.
Wireless extensions procfs support is auto-selected
based on PROC_FS and anything that requires the wext core
(i.e. WIRELESS_EXT or CFG80211_WEXT).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the hostap driver was converted to use net_device_ops, a mistake was
made in hostap_main.c (commit 5ae4efbcd2).
Originally, the tx_queue_len was set to 0 for every other interface than
HOSTAP_INTERFACE_MASTER, but the new fragment of code sets tx_queue_len to
0 only for HOSTAP_INTERFACE_MASTER. The opposite of the previous
behavior makes the driver to drop all packets in AP mode.
Change the way 0 is assigned to tx_queue_len according to the original
logic.
Signed-off-by: Martin Decky <martin@decky.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mostly just simple conversions:
* ray_cs had bogus return of NET_TX_LOCKED but driver
was not using NETIF_F_LLTX
* hostap and ipw2x00 had some code that returned value
from a called function that also had to change to return netdev_tx_t
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hostap_cs driver is programmed for exclusive rather that shared
interrupts.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-and-Tested-by: Jack Schneider <puck@dp-indexing.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts the remaining occurences of raw return values to their
symbolic counterparts in ndo_start_xmit() functions that were missed by the
previous automatic conversion.
Additionally code that assumed the symbolic value of NETDEV_TX_OK to be zero
is changed to explicitly use NETDEV_TX_OK.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.
0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Patch fixes issues with dev->dev_addr changing from array to pointer.
Hopefully there are no others.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mac80211/tx.c: In function ‘ieee80211_tx_h_select_key’:
net/mac80211/tx.c:448: warning: ‘key’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/rc.c: In function ‘ath_rc_rate_getidx’:
drivers/net/wireless/ath/ath9k/rc.c:815: warning: ‘nextindex’ may be used uninitialized in this function
drivers/net/wireless/hostap/hostap_plx.c: In function ‘prism2_plx_probe’:
drivers/net/wireless/hostap/hostap_plx.c:438: warning: ‘cor_index’ may be used uninitialized in this function
drivers/net/wireless/hostap/hostap_plx.c:438: warning: ‘cor_offset’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use pre-existing net_device_stats in network_device struct.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that net/ieee80211.h can be made private to ipw2x00 in a follow-up.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These bits are shared already between ipw2x00 and hostap, and could
probably be shared both more cleanly and with other drivers. This
commit simply relocates the code to lib80211 and adjusts the drivers
appropriately.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Like mac80211 did, this driver makes 'clever' use of skb->cb to pass
information along with an skb as it is requeued from the virtual device
to the physical wireless device. Unfortunately, that trick no longer
works...
Unlike mac80211, code complexity and driver apathy makes this hack
the best option we have in the short run. Hopefully someone will
eventually be motivated to code a proper fix before all the effected
hardware dies.
(Above text by me. Johannes officially disavows all knowledge of this
hack. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
A compilation with the command "make C=2 CF="-D__CHECK_ENDIAN__" \
drivers/net/wireless/hostap/"
yields the following warnings:
CHECK drivers/net/wireless/hostap/hostap_info.c
drivers/net/wireless/hostap/hostap_info.c:156:43: warning: incorrect type in
argument 2 (different signedness)
drivers/net/wireless/hostap/hostap_info.c:156:43: expected unsigned long
volatile *addr
drivers/net/wireless/hostap/hostap_info.c:156:43: got long *<noident>
drivers/net/wireless/hostap/hostap_info.c:294:44: warning: incorrect type in
argument 2 (different signedness)
drivers/net/wireless/hostap/hostap_info.c:294:44: expected unsigned long
volatile *addr
drivers/net/wireless/hostap/hostap_info.c:294:44: got long *<noident>
drivers/net/wireless/hostap/hostap_info.c:487:12: warning: incorrect type in
argument 2 (different signedness)
drivers/net/wireless/hostap/hostap_info.c:487:12: expected unsigned long
volatile *addr
drivers/net/wireless/hostap/hostap_info.c:487:12: got long *<noident>
drivers/net/wireless/hostap/hostap_info.c:491:12: warning: incorrect type in
argument 2 (different signedness)
drivers/net/wireless/hostap/hostap_info.c:491:12: expected unsigned long
volatile *addr
drivers/net/wireless/hostap/hostap_info.c:491:12: got long *<noident>
The warnings are fixed with the following compile-tested fix:
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the newly introduced pci_ioremap_bar() function in drivers/net.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we're just parsing the tuple being passed to this function, we don't
need any device-specific information.
Also, remove the call to pcmcia_validate_cis() from pcmciamtd.c, since it
is already called by the PCMCIA core.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Instead of using own error or success codes, the PCMCIA code should rely on
the generic return values. Therefore, replace all occurrences of CS_SUCCESS
with 0.
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
By passing the current Vcc setting to the pcmcia_config_loop callback
function, we can remove pcmcia_get_configuration_info() calls from many
drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Many drivers use the default CIS entry within their pcmcia_config_loop()
callback function. Therefore, factor the default CIS entry handling out.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Almost all drivers set p_dev->conf.ConfigIndex to cfg->index in
the pcmcia_config_loop() callback function. Therefore, factor it out.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The new address list lock needs to handle the same device layering
issues that the _xmit_lock one does.
This integrates work done by Patrick McHardy.
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_netdev_mq() now allocates an array of netdev_queue
structures for TX, based upon the queue_count argument.
Furthermore, all accesses to the TX queues are now vectored
through the netdev_get_tx_queue() and netdev_for_each_tx_queue()
interfaces. This makes it easy to grep the tree for all
things that want to get to a TX queue of a net device.
Problem spots which are not really multiqueue aware yet, and
only work with one queue, can easily be spotted by grepping
for all netdev_get_tx_queue() calls that pass in a zero index.
Signed-off-by: David S. Miller <davem@davemloft.net>
Accesses are mostly structured such that when there are multiple TX
queues the code transformations will be a little bit simpler.
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide MAC time, rate, channel, signal and noise.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't try to skip any headers in hostap_80211_header_parse(). We never
use that function for interfaces affected by local->monitor_type. Both
the master and the AP interface receive 802.11 frames without any
additional headers.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rewrite AID calculation in handle_pspoll() to avoid truncating bits.
Make hostap_80211_header_parse() static, don't export it. Avoid
shadowing variables.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DEBUG_EXTRA is reported to the kernel log by default, but DEBUG_EXTRA2
is not. Unrelated WDS frames pollute the log unnecessarily.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Three major portions to this change:
1) Add IW_EV_COMPAT_LCP_LEN, IW_EV_COMPAT_POINT_OFF,
and IW_EV_COMPAT_POINT_LEN helper defines.
2) Delete iw_stream_check_add_*(), they are unused.
3) Add iw_request_info argument to iwe_stream_add_*(), and use it to
size the event and pointer lengths correctly depending upon whether
IW_REQUEST_FLAG_COMPAT is set or not.
4) The mechanical transformations to the drivers and wireless stack
bits to get the iw_request_info passed down into the routines
modified in #3. Also, explicit references to IW_EV_LCP_LEN are
replaced with iwe_stream_lcp_len(info).
With a lot of help and bug fixes from Masakazu Mokuno.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the RTNL is held when we invoke flush_scheduled_work() we could
deadlock. One such case is linkwatch, it is a work struct which tries
to grab the RTNL semaphore.
The most common case are net driver ->stop() methods. The
simplest conversion is to instead use cancel_{delayed_}work_sync()
explicitly on the various work struct the driver uses.
This is an OK transformation because these work structs are doing
things like resetting the chip, restarting link negotiation, and so
forth. And if we're bringing down the device, we're about to turn the
chip off and reset it anways. So if we cancel a pending work event,
that's fine here.
Some drivers were working around this deadlock by using a msleep()
polling loop of some sort, and those cases are converted to instead
use cancel_{delayed_}work_sync() as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by Santiago Garcia Mantinan <hostap@manty.net>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The "registers" entry was incorrectly created in the procfs root instead
of the device specific directory. Move "registers" registration
immediately after the containing procfs directory is created.
Signed-off-by: Mathieu Chouquet-Stringer <mchouque@free.fr>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If print_mac() is used inside of a pr_debug() the compiler
can't see that the call is redundant so still performs it
even of pr_debug() ends up being a nop.
So don't use print_mac() in such cases in hot code paths,
use MAC_FMT et al. instead.
As noted by Joe Perches, pr_debug() could be modified to
handle this better, but that is a change to an interface
used by the entire kernel and thus needs to be validated
carefully. This here is thus the less risky fix for
2.6.25
Signed-off-by: David S. Miller <davem@davemloft.net>
Card reported by Ångström user:
http://bugs.openembedded.net/show_bug.cgi?id=3236
Socket 1:
product info: "Wireless LAN", "11Mbps PC Card", "Version 01.02", ""
manfid: 0x0156, 0x0002
function: 6 (network)
Signed-off-by: Marcin Juszkiewicz <openembedded@haerwu.biz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were two identical prototypes for hostap_80211_rx() in
drivers/net/wireless/hostap/hostap_80211.h.
This patch fixes kernel Bugzilla #8930.
Reported by Christoph Burger-Scheidlin.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the third PCMCIA ID string specifies the MAC chip, the fourth ID
string doesn't need to be matched. Even if it's different, it will be
compatible with the driver.
This ensures that other different revisions of the card will be
supported.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just leave hfa384x_info_frame as-is, don't convert in place.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* use irq_handler_t where appropriate
* no need to use 'irq' function arg, its already stored in a data struct
* rename irq handler 'irq' argument to 'dummy', where the function
has been analyzed and proven not to use its first argument.
* remove always-false "dev_id == NULL" test from irq handlers
* remove pointless casts from void*
* declance: irq argument is not const
* add KERN_xxx printk prefix
* fix minor whitespace weirdness
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce scan capabilities to WEXT so that userspace can do intelligent
things with scan behavior such as handling hidden SSIDs more gracefully.
If the driver reports a specific scan capability, the driver must
respect the options specified in the iw_scan_req structure when handling
the SIOCSIWSCAN call, unless it's mode or state does not allow it to do
so, in which case it must return an error.
This version switches to Dave Kilroy's suggestion of claiming unused
padding space for the scan_capa field.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix section mismatch by changing variable name to match one of the
whitelisted (allowable) names for pointing into init data:
WARNING: vmlinux.o(.data+0xce618): Section mismatch: reference to .init.data:prism2_plx_id_table (between 'prism2_plx_drv_id' and 'dev_info')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix section mismatch warning:
WARNING: vmlinux.o(.data+0x36fcc): Section mismatch: reference to .init.data:prism2_pci_id_table (between 'prism2_pci_drv_id' and 'prism2_pci_funcs')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The task_struct->pid member is going to be deprecated, so start
using the helpers (task_pid_nr/task_pid_vnr/task_pid_nr_ns) in
the kernel.
The first thing to start with is the pid, printed to dmesg - in
this case we may safely use task_pid_nr(). Besides, printks produce
more (much more) than a half of all the explicit pid usage.
[akpm@linux-foundation.org: git-drm went and changed lots of stuff]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
define global BIT macro
move all local BIT defines to the new globally define macro.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
deal with signedness of the stuff passed to set_bit() et.al.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As detailed at https://bugs.gentoo.org/159646 hostap with hostapd confuses
udev by presenting 2 interfaces with the same MAC address. Also, at the time
of detection, the 'type' attribute is 1, identical to other hostap interfaces.
The AP interface is supposed to have type ARPHRD_IEEE80211 (801), but this is
not set until after registration.
Setting it before register_netdev() is called allows us to avoid this
confusion. We can do this by propogating the HOSTAP_INTERFACE type through
to hostap_setup_dev().
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hardware header operations are part of the protocol class
not the device instance, make them into a separate object and
save memory.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Host AP driver uses a semaphore as mutex. Use the mutex API
instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes /proc/net per network namespace. It modifies the global
variables proc_net and proc_net_stat to be per network namespace.
The proc_net file helpers are modified to take a network namespace argument,
and all of their callers are fixed to pass &init_net for that argument.
This ensures that all of the /proc/net files are only visible and
usable in the initial network namespace until the code behind them
has been updated to be handle multiple network namespaces.
Making /proc/net per namespace is necessary as at least some files
in /proc/net depend upon the set of network devices which is per
network namespace, and even more files in /proc/net have contents
that are relevant to a single network namespace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove pointless and never-called enable_wake() hook from pci_driver and
from documentation. Evidently this was introduced in the 2.4.6 kernel,
but there's no evidence it was ever called; and it was rarely implemented.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver version number has not been updated since the driver was
included in the main kernel tree and there is no plan on updating this
in the future either. At this point, the only correct way to refer to
the version is to use the kernel version. The 0.4.4 version is
confusing since there are external version with higher version number
even though they are not actually any newer than the in-tree version.
Let's get rid of the version number in the kernel tree in order to
avoid this kind of confusion.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use list_for_each_entry() instead of manual iteration and
substitute some list_for_each() loops with list_for_each_entry().
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This may be useful in mesh setups when most stations act as repeaters only.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hostap_tx_encrypt() tries to allocate enough headroom and
tailroom for ieee80211 encryption, it only makes enough room for the
"mpdu" phase of the operation, but forgets about the "msdu" phase.
(For TKIP, these two phases require, respectively, 4 and 8 bytes of
tailroom, per the "ieee80211_crypt_tkip" structure at the bottom of
net/ieee80211/ieee80211_crypt_tkip.c.)
Signed-off-by: Brandon Craig Rhodes <brandon@rhodesmill.org>
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Justin P. Mattock