Currently BA notifications which don't reclaim any frames
would not cause the RS to be called as no skbs are passed
to mac80211. This is not optimal as RS can benefit from the
statistics of sent vs. acked of such a BA. This can improve the
reaction time of the RS algorithm. Also, an upcoming change in
the firmware would cause BA timeout to be reported as a BA notif
with 0 acked so this change is required for that as well.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The 8000 HW series also includes the revision in the FW
name.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Align the trans->hw_rev variable format with previous series
format.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is a tradeoff between enabling better throughput for
bursty traffic and low latency. The number 6 was found to be
a good tradeoff for the Miracast use case which is the
major use case for low latency.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable RS to get updated directly via iwl_mvm_rs_tx_status
which will be called by the driver and not via mac80211
rate control. This is required for a following patch to
report on BAs which do not cause the BA window to progress.
Also this is a first step in decoupling rs from the
mac80211 rate control.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Improve the initial tx rate and antenna selection to be based on
the rssi of the last rx. This avoids starting at the lowest legacy
rate always and requiring more tx traffic to "climb" up the rates.
Since this option might cause trouble in certain setups, allow to
disable it by default.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We can only determine the final security level when both pairing request
and response have been exchanged. When initiating pairing the starting
target security level is set to MEDIUM unless explicitly specified to be
HIGH, so that we can still perform pairing even if the remote doesn't
have MITM capabilities. However, once we've received the pairing
response we should re-consult the remote and local IO capabilities and
upgrade the target security level if necessary.
Without this patch the resulting Long Term Key will occasionally be
reported to be unauthenticated when it in reality is an authenticated
one.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
As suggeested by checkpatch:
WARNING: Prefer ether_addr_copy() over memcpy() if the Ethernet addresses are __aligned(2)
In wmi.c I had to change due to sparse warnings copying of struct wmi_mac_addr
from form &cmd->peer_macaddr.addr to cmd->peer_macaddr.addr. In
ath10k_wmi_set_ap_ps_param() I also added the missing ".addr" to the copy
command.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Makes it more readable and fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/debug.c:593: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:594: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:595: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:596: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:597: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:599: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:600: WARNING: quoted string split across lines
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
ath10k/htc.c:49: WARNING: Possible unnecessary 'out of memory' message
ath10k/htc.c:810: WARNING: Possible unnecessary 'out of memory' message
ath10k/htt.h:1034: CHECK: Please use a blank line after function/struct/union/enum declarations
ath10k/htt_rx.c:135: CHECK: Unnecessary parentheses around htt->rx_ring.alloc_idx.vaddr
ath10k/htt_rx.c:173: CHECK: Unnecessary parentheses around htt->rx_ring.alloc_idx.vaddr
ath10k/pci.c:633: WARNING: macros should not use a trailing semicolon
ath10k/wmi.c:3594: WARNING: quoted string split across lines
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
WARNING: Missing a blank line after declarations
Please note that some of the cases I fixed by moving the variable declarations
to the beginning of the function, which is the preferred style in ath10k.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The hci_recv_fragment function is no longer used by any driver and thus
do not export it. In fact it is not even needed by the core and it can
be removed altogether.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Enable pulse detection on extension channel if 40MHz channel width has been set
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This happens when CONFIG_ATH9K_CHANNEL_CONTEXT is
not enabled.
../drivers/net/wireless/ath/ath9k/recv.c: In function ‘ath_rx_ps_beacon’:
../drivers/net/wireless/ath/ath9k/recv.c:553:27: error: ‘struct ath_softc’ has no member named ‘offchannel’
if (sc->cur_chan == &sc->offchannel.chan)
^
../scripts/Makefile.build:257: recipe for target 'drivers/net/wireless/ath/ath9k/recv.o' failed
make[10]: *** [drivers/net/wireless/ath/ath9k/recv.o] Error 1
../scripts/Makefile.build:404: recipe for target 'drivers/net/wireless/ath/ath9k' failed
make[9]: *** [drivers/net/wireless/ath/ath9k] Error 2
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize neighbor linked list used by dynack to compute ACK timeout
as the maximum STA ACK timeout
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable ACK timeout estimation algorithm if set_coverage_class routine has been
called with negative coverage_class parameter. Dynack is automatically disabled
setting valid value for coverage class
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ack_to entry to debugfs in order to dump current ACK timeout value
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set control frame bit in rx filter if dynack processing has been activated
in order to enable ACK frame reception
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add sampling methods for ACK RX timestamp in ath_rx_tasklet() and for TX frame
timestamp in ath_tx_complete_aggr() and in ath_tx_process_buffer(). These
samples will be used in dynack processing for ACK timeout estimation
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not overwrite ACK timeout estimation in ath9k_hw_init_global_settings() if
dynack processing has been enabled
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ACK timeout estimation algorithm to ath9k Makefile and Kconfig
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add dynamic ACK timeout estimation algorithm based on ACK frame RX timestamp,
TX frame timestamp and frame duration.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Tested-by: Philippe Duchein <wireless-dev@duchein.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add duration field to ath_tx_status in order to report frame duration for each
entry in multi-retry chain. These fields will be used in ACK timeout estimation
algorithm (dynack)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove static keyword and export ath9k_hw_setslottime(),
ath9k_hw_set_ack_timeout() and ath9k_hw_set_cts_timeout() in hw.h.
These methods will be used in ACK timeout estimation algorithm (dynack)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receiving USB interrupt, bulk or isochronous packet, they normally
come in fragments. So far the driver just handed each fragment off to
the hci_recv_fragment function of the Bluetooth core. That function is
however so specific that is does not belong in the core. This patch
implements the same reassembly logic in the driver.
In addition this fixes a long standing bug where multiple complete
packets are received within a single USB packet.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In the past when schedule scan was started while connected on one of
interfaces FW crashes were observed. In the newest FW this issue is
solved, so remove limitaion after examining corresponding TLV flag.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When read, this new debugfs entry requests the current temperature
from the firmware and outputs it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The scheduler is a HW sub-block that directs the work of the Flow
Handler by issuing requests for frame transfers, specifying source
and destination. Its primary function is to allocate flows into the
TX FIFOs based upon a pre-determined mapping.
The driver has some responsibilities to the scheduler, namely
initialising and maintaining the hardware registers. This is
currently done by directly accessing them, which can cause races
with the firmware also accessing the registers.
To address this problem, change the driver to no longer directly
access the registers but go through the firmware for this if the
firmware has support for DQA and thus the new command.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Set RRM_ENABLED (bit 6) flag in scan commands. When this flag is set
the fw will add WFA vendor-specific TPC report and DS parameter set
IEs into probe requests.
This bit is set for SCAN_OFFLOAD_REQUEST_CMD(0x51).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Assaf Krauss <assaf.krauss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add a ucode capability flag for support of Quiet Period (part of RRM).
If this flag is set, advertise device support.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Introduce new tx command flag (TX_CMD_FLG_WRITE_TX_POWER) which requests the
fw to update the tx power value at some constant offset.
Set this flag when transmitting either TPC report or Link measurement report
action frames.
In addition, introduce new tlv which indicates whether the fw supports power
insertion (IWL_UCODE_TLV_CAPA_TXPOWER_INSERTION_SUPPORT) and publish the
corresponding nl80211 feature.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since tx skbs are not modified by the driver, let mac80211 know the
driver can handle cloned skbs.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The actual packet reassembly should be done inside the driver. To allow
this to happen cleanly in future patches, split the fragment reception
into its own functions.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btusb driver has been around for a while now and it is time to
bring its coding style in sync with what has been done for the
Bluetooth subsystem and other drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Assign 'primary_sta' to the active primary station
interface after iterating over the list of interfaces.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The opmode is verified to be NL80211_IFTYPE_STATION
before calling ath9k_set_assoc_state().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When switching offchannel, BSS related information
in the HW has to be reset to default values. Add a routine
to do this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In MCC mode, the TSF of a context needs to be
adjusted only if it is GO/AP.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The next_tbtt variable in the scheduler is needed only
for GO/AP mode operation and is always read from the
NEXT_TBTT_TIMER in the HW. There is no need to store
the timestamp for received beacons.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some constants were missing and are added now.
The rate mode was renamed, at least the ucode in brcsmac uses 2 for HT
rates (iee80211n) and the more recent ucodes are using 3 for VHT
(ieee80211ac).
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eyal Shapira