Since commit e042681894 ("ARM: shmobile: r8a7790: Remove legacy
code"), all R-Car Gen2 SoCs are supported by multiplatform kernels only.
As CONFIG_COMMON_CLK is always set for multiplatform kernels, we can
remove related #ifdefs in code specific to R-Car Gen2 SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7790/lager and r8a7791/koelsch development boards have da9063 and
da9210 regulators. Both regulators have their interrupt request lines
tied to the same interrupt pin (IRQ2) on the SoC.
After cold boot or da9063-induced restart, both the da9063 and da9210
seem to assert their interrupt request lines. Hence as soon as one
driver requests this irq, it gets stuck in an interrupt storm, as it
only manages to deassert its own interrupt request line, and the other
driver hasn't installed an interrupt handler yet.
To handle this, install a quirk that masks the interrupts in both the
da9063 and da9210. This quirk has to run after the i2c master driver
has been initialized, but before the i2c slave drivers are initialized.
As it depends on i2c, select I2C if one of the affected platforms is
enabled in the kernel config.
On koelsch, the following happens:
- Cold boot or reboot using the da9063 restart handler:
IRQ2 is asserted, installing da9063/da9210 regulator quirk
...
i2c i2c-6: regulator_quirk_notify: 1, IRQC_MONITOR = 0x3fb
i2c 6-0058: regulator_quirk_notify: 1, IRQC_MONITOR = 0x3fb
i2c 6-0058: Detected da9063
i2c 6-0058: Masking da9063 interrupt sources
i2c 6-0068: regulator_quirk_notify: 1, IRQC_MONITOR = 0x3fb
i2c 6-0068: Detected da9210
i2c 6-0068: Masking da9210 interrupt sources
i2c 6-0068: IRQ2 is not asserted, removing quirk
- Warm boot (reset button):
rcar_gen2_regulator_quirk: IRQ2 is not asserted, not installing quirk
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current sh_mobile_sdhi's platform data is set via sh_mobile_sdhi_info
and it is just copied to tmio_mmc_data.
Now, tmio mmc platform data is specified via tmio_mmc_data.
This patch replace sh_mobile_sdhi_info to tmio_mmc_data
struct sh_mobile_sdhi_info { -> struct tmio_mmc_data {
int dma_slave_tx; -> void *chan_priv_tx;
int dma_slave_rx; -> void *chan_priv_rx;
unsigned long tmio_flags; -> unsigned long flags;
unsigned long tmio_caps; -> unsigned long capabilities;
unsigned long tmio_caps2; -> unsigned long capabilities2;
u32 tmio_ocr_mask; -> u32 ocr_mask;
unsigned int cd_gpio; -> unsigned int cd_gpio;
}; unsigned int hclk;
void (*set_pwr)(...);
void (*set_clk_div)(...);
};
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* Remove the sh7372 SoC and its mackerel board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Lpw8
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh7372-soc-removal-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/multiplatform
Pull "Renesas ARM Based SoC sh7372 SoC Removal Updates for v4.1" from Simon Horman:
* Remove the sh7372 SoC and its mackerel board
* tag 'renesas-sh7372-soc-removal-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
Documentation: Remove ZBOOT MMC/SDHI utility and docs
ARM: shmobile: sh7372 dtsi: Remove Legacy DTSI file
ARM: shmobile: sh7372: Remove DT binding documentation
ARM: shmobile: sh7372: Remove Legacy C SoC code
ARM: shmobile: sh7372: Remove ZBOOT MMC/SDHI support
ARM: shmobile: mackerel: Remove from MAINTAINERS
ARM: shmobile: mackerel: Remove defconfig
ARM: shmobile: mackerel: Remove mach-type entry
ARM: shmobile: mackerel: Remove DT binding documentation
ARM: shmobile: mackerel dts: Remove Legacy DTS file
ARM: shmobile: mackerel: Remove Legacy C board code
ARM: shmobile: mackerel: Remove ZBOOT code
[arnd: The sh7372 platform is rather dated and is believed to
have no active users on modern kernels. It stands in the way
of converting all of mach-shmobile to be multiplatform capable,
as adding pinctrl and common-clock support for it would be more
work than it's worth. As always, should any legitimate upstream
users show up in the future, we will revert this removal]
All r8a73a4 boards are now used with multiplatform kernels only. We can
remove all the unused r8a73a4 legacy device and clock registration code.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove the restart handling hack from the sh73a0 generic multiplatform
case.
Restart on DT-based sh73a0 platforms is now handled through the
R-Mobile reset driver.
This basically reverts commit cad900819f ("ARM: shmobile: sh73a0:
Add restart callback").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
"ARM: shmobile: kzm9g-reference: Remove board C code and DT file"
removed the last user of sh73a0_add_standard_devices_dt(). Hence remove
this function.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the sh73a0 generic multiplatform case has the same feature set
as the kzm9g DT reference board code, we get rid of the latter.
DT reference code in the future shall make use of the sh73a0
multiplatform support code with the generic SoC machine vector.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable sh73a0 Multiplatform support for the generic sh73a0
machine vector. No board support is enabled, and the board
code for KZM9G DT Reference is left by itself.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a generic sh73a0 machine setup callback for the upcoming
sh73a0 multiplatform case. Cache needs to be configured, and
legacy clocks must be omitted.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Allow R-Car Gen2 platforms to boot with CMA enabled
and HIGHMEM disabled. This patch adds code to check
if the R-Car Gen2 specific memory reservation window
is included in the kernel memory range or not. When
HIGHMEM is disabled the R-Car Gen2 reservation area is
outside the kernel memory range and in such case the
memory reservation is simply skipped over.
Without this patch the kernel boot hangs when CMA is
enabled and HIGHMEM is disabled on the r8a7791 Koelsch
hardware platform:
WARNING: CPU: 1 PID: 1 at mm/cma.c:113 cma_init_reserved_areas+0x88/0x1d4()
...
WARNING: CPU: 1 PID: 1 at mm/cma.c:121 cma_init_reserved_areas+0xf8/0x1d4()
...
Unable to handle kernel NULL pointer dereference at virtual address 00000160
pgd = c0003000
[00000160] *pgd=80000040004003, *pmd=00000000
Internal error: Oops: 206 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Tainted: G W
3.19.0-rc4-koelsch-01450-g7f9b6075ce12c3ea-dirty #735
Hardware name: Generic R8A7791 (Flattened Device Tree)
task: edc553c0 ti: edc56000 task.ti: edc56000
PC is at set_pfnblock_flags_mask+0x54/0xa0
LR is at 0x440
In the current shmobile_defconfig HIGHMEM is enabled
while CMA is disabled, so to trigger this the kernel
configuration for both CMA and HIGHMEM needs to be
adjusted.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
By default only the non-boot CPUs can be hotplugged if the
smp_operations structure doesn't have the cpu_disable function
pointer set. r8a7779_cpu_disable() implements the same logic,
only non-boot CPUs can be hotplugged, so it's redundant to
override the default behavior.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Convert ARCH_SHMOBILE_LEGACY to make use of <debug/uncompress.h>
and remove the now unused <mach/uncompress.h>.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move over ARCH_SHMOBILE_LEGACY to use the default legacy ARM
implementations of __clk_get() and __clk_put() in <asm/clkdev.h>
by deselecting HAVE_MACH_CLKDEV. This has the nice side effect
that <mach/clkdev.h> is no longer used and can be removed.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The file <mach/system.h> is no longer included from anywhere so
clean up the code by removing mach-shmobile/include/mach/system.h
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove support for the legacy Cortex-A8 based sh7372 SoC.
The Linux kernel still lacks DT bindings for the sh7372 INTC
interrupt controller so DT multiplatform support is not possibile.
Also, the sh7372 SoC never went into mass production anyway so to
aid migration to DT multiplatform simply get rid of sh7372 support.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove the sh7372 implementation and the shared ZBOOT MMC
and SDHI support code from the compressed ARM boot loader.
With this in place it is no longer possible to boot any
self-contained kernel for sh7372 directly from Mask ROM
via SDHI and MMCIF hardware.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove legacy C code for the sh7372 Mackerel board. There is no
DT multiplatform implementation available for the sh7372 SoC so
simply phase out the board and SoC code support.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove ZBOOT support code for Mackerel. With this patch in place
it is no longer possible to boot a self-contained kernel directly
from the reset vector. ZBOOT is still supported on kzm9g.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Disables the legacy clock framework and passes the mode bits to the CPG
driver if CCF is enabled.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This removes the remains of the legacy ape6evm platform.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the r8a73a4 generic multiplatform case has the same features as the
APE6EVM DT reference board code, we get rid of the latter. DT reference
code in the future shall make use of the r8a73a4 multiplatform support code
with the generic SoC machine vector.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[geert: Update Documentation/devicetree/bindings/arm/shmobile.txt]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Documentation says the last register is at 0x184 (CAxCPUCMCR), so use
proper length. Current APMU code accesses CAxCPUnCR which is currently
outside of the remapped area.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Documentation says the last register is at 0x184 (CAxCPUCMCR), so use
proper length. Current APMU code accesses CAxCPUnCR which is currently
outside of the remapped area.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The definition
static const char *axxia_dt_match[] __initconst = {
...
defines a changable array of constant strings. That is you must not do:
*axxia_dt_match[0] = 'k';
but
axxia_dt_match[0] = "different string";
is fine. So the annotation __initconst is wrong and yields a compiler
error when other really const variables are added with __initconst.
As the struct machine_desc member dt_compat is declared as
const char *const *dt_compat;
making the arrays const is the better alternative over changing all
annotations to __initdata.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
This time around, much of this is for at91, with the bulk of it being syscon
and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJU4upSAAoJEIwa5zzehBx3HkUP/Rc4B1yZChNIFNfVq4dbei6w
dT9WdFmxOIj2JLeXEypFBiNf1nSHmsxrZe9/IDACz2fYQOnaZZ6/786utUJP/PtC
2GDJy9cjL2Xh03We3nQp5z6J33XvpEni1t82cOpCl8wLBOQNnkjEks8UvLgi1LHW
CNLcMm8JtDQ2aB/gRTjzetp9liZluESY5+Mig+loE2F/rzbMbNQDcWDDgUPyIQIS
1onL+Bad3BnGFdo/+qnkurGc81pxoKiQJty06VWFftzvIwxXhsNjrqls2+KzstAx
0lLvW1tqaDhXvUBImRM8GgfbldZslsgoFVmgESS9MpPMBNENYrkAiQNvJUnM7kd9
qHDQNq+zRNsz/k4fVvp/YUp7xEiAo4rLcFmp/dBr535jS2LNyiZnB94q+kXsin/m
tiyEMx+RWxEHTEHN9WdKE61Ty1RbzOa5UTLSzOKFAkF+m2nvuQsJvb97n19coAq9
SSsj/wJgesfqrDEegphCDh1fyVxUzlAjjhTAyvPS155WvPzkbxZxuBbSqRuriRKA
2aCfVne2ELimHAr3LEPgPW2kFBcONHckOGe6MvrTX4zPHU8bb9WIeg+iGdQChnr3
nclT9jq+ZnQro5XTgUtPtadq100oEXlJbqpAzhd+cJbvgzSNbcWfcgE6kOWqd9uK
oeWQWFLCdXLmXf9zCwmk
=T7R2
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
This time around, much of this is for at91, with the bulk of it being
syscon and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
cpuidle: exynos: add coupled cpuidle support for exynos4210
ARM: EXYNOS: apply S5P_CENTRAL_SEQ_OPTION fix only when necessary
soc: ti: knav_qmss_queue: change knav_range_setup_acc_irq to static
soc: ti: knav_qmss_queue: makefile tweak to build as dynamic module
pcmcia: at91_cf: depend on !ARCH_MULTIPLATFORM
soc: ti: knav_qmss_queue: export API calls for use by user driver
of/platform: teardown DMA mappings on device destruction
usb: gadget: at91_udc: Allocate udc instance
usb: gadget: at91_udc: Update DT binding documentation
usb: gadget: at91_udc: Rework for multi-platform kernel support
usb: gadget: at91_udc: Simplify probe and remove functions
usb: gadget: at91_udc: Remove non-DT handling code
usb: gadget: at91_udc: Document DT clocks and clock-names property
usb: gadget: at91_udc: Drop uclk clock
usb: gadget: at91_udc: Fix clock names
mfd: syscon: Add Atmel SMC binding doc
mfd: syscon: Add atmel-smc registers definition
mfd: syscon: Add Atmel Matrix bus DT binding documentation
mfd: syscon: Add atmel-matrix registers definition
clk: shmobile: fix sparse NULL pointer warning
...
New and updated SoC support. Also included are some cleanups where the
platform maintainers hadn't separated cleanups from new developent in
separate branches.
Some of the larger things worth pointing out:
- A large set of changes from Alexandre Belloni and Nicolas Ferre
preparing at91 platforms for multiplatform and cleaning up quite a
bit in the process.
- Removal of CSR's "Marco" SoC platform that never made it out to the
market. We love seeing these since it means the vendor published
support before product was out, which is exactly what we want!
New platforms this release are:
- Conexant Digicolor (CX92755 SoC)
- Hisilicon HiP01 SoC
- CSR/sirf Atlas7 SoC
- ST STiH418 SoC
- Common code changes for Nvidia Tegra132 (64-bit SoC)
We're seeing more and more platforms having a harder time labelling
changes as cleanups vs new development -- which is a good sign that
we've come quite far on the cleanup effort. So over time we might start
combining the cleanup and new-development branches more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=szd9
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Also included are some cleanups where
the platform maintainers hadn't separated cleanups from new developent
in separate branches.
Some of the larger things worth pointing out:
- A large set of changes from Alexandre Belloni and Nicolas Ferre
preparing at91 platforms for multiplatform and cleaning up quite a
bit in the process.
- Removal of CSR's "Marco" SoC platform that never made it out to the
market. We love seeing these since it means the vendor published
support before product was out, which is exactly what we want!
New platforms this release are:
- Conexant Digicolor (CX92755 SoC)
- Hisilicon HiP01 SoC
- CSR/sirf Atlas7 SoC
- ST STiH418 SoC
- Common code changes for Nvidia Tegra132 (64-bit SoC)
We're seeing more and more platforms having a harder time labelling
changes as cleanups vs new development -- which is a good sign that
we've come quite far on the cleanup effort. So over time we might
start combining the cleanup and new-development branches more"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (124 commits)
ARM: at91/trivial: unify functions and machine names
ARM: at91: remove at91_dt_initialize and machine init_early()
ARM: at91: change board files into SoC files
ARM: at91: remove at91_boot_soc
ARM: at91: move alternative initial mapping to board-dt-sama5.c
ARM: at91: merge all SOC_AT91SAM9xxx
ARM: at91: at91rm9200: set idle and restart from rm9200_dt_device_init()
ARM: digicolor: select syscon and timer
ARM: zynq: Simplify SLCR initialization
ARM: zynq: PM: Fixed simple typo.
ARM: zynq: Setup default gpio number for Xilinx Zynq
ARM: digicolor: add low level debug support
ARM: initial support for Conexant Digicolor CX92755 SoC
ARM: OMAP2+: Add dm816x hwmod support
ARM: OMAP2+: Add clock domain support for dm816x
ARM: OMAP2+: Add board-generic.c entry for ti81xx
ARM: at91: pm: remove warning to remove SOC_AT91SAM9263 usage
ARM: at91: remove unused mach/system_rev.h
ARM: at91: stop using HAVE_AT91_DBGUx
ARM: at91: fix ordering of SRAM and PM initialization
...
This is a good healthy set of various code removals. Total net delta is 8100
lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tsjK
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is a good healthy set of various code removals. Total net delta
is 8100 lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (47 commits)
ARM: sirf: drop redundant function and marco declaration
arm: omap: specify PMUs are for ARMv7 CPUs
arm: shmobile: specify PMUs are for ARMv7 CPUs
arm: iop: specify PMUs are for XScale CPUs
arm: pxa: specify PMUs are for XScale CPUs
arm: realview: specify PMU types
ARM: SAMSUNG: remove unused DMA infrastructure
ARM: OMAP3: Add back Kconfig option MACH_OMAP3517EVM for ASoC
ARM: davinci: Remove CDCE949 driver
ARM: at91: remove useless at91rm9200_set_type()
ARM: at91: remove useless at91rm9200_dt_initialize()
ARM: at91: move debug-macro.S into the common space
ARM: at91: remove useless at91_sysirq_mask_rtx
ARM: at91: remove useless config MACH_AT91SAM9_DT
ARM: at91: remove useless config MACH_AT91RM9200_DT
ARM: at91: remove unused mach/memory.h
ARM: at91: remove useless header file includes
ARM: at91: remove unneeded header file
rtc: at91/Kconfig: remove useless options
ARM: at91/Documentation: add a README for Atmel SoCs
...
Now that we can specify which PMU variant we're likely to deal with, do
so in the shmobile board code. This will allow us to split the ARMv6,
ARMv7, and XScale PMU drivers
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
* Instantiate GIC from C board code in legacy builds on r8a7790 and r8a73a4
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/Oq9
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-fixes3-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Third Round of Renesas ARM Based SoC Fixes for v3.19" from Simon Horman:
* Instantiate GIC from C board code in legacy builds on r8a7790 and r8a73a4
* tag 'renesas-soc-fixes3-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: Instantiate GIC from C board code in legacy builds
ARM: shmobile: r8a73a4: Instantiate GIC from C board code in legacy builds
Signed-off-by: Olof Johansson <olof@lixom.net>
As of commit 9a1091ef00 ("irqchip: gic: Support hierarchy irq
domain."), the Lager legacy board support is known to be broken.
The IRQ numbers of the GIC are now virtual, and no longer match the
hardcoded hardware IRQ numbers in the legacy platform board code.
To fix this issue specific to non-multiplatform r8a7790 and Lager:
1) Instantiate the GIC from platform board code and also
2) Skip over the DT arch timer as well as
3) Force delay setup based on DT CPU frequency
With these 3 fixes in place interrupts on Lager are now unbroken.
Partially based on legacy GIC fix by Geert Uytterhoeven, thanks to
him for the initial work.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 9a1091ef00 ("irqchip: gic: Support hierarchy irq
domain."), the APE6EVM legacy board support is known to be broken.
The IRQ numbers of the GIC are now virtual, and no longer match the
hardcoded hardware IRQ numbers in the legacy platform board code.
To fix this issue specific to non-muliplatform r8a73a4 and APE6EVM:
1) Instantiate the GIC from platform board code and also
2) Skip over the DT arch timer as well as
3) Force delay setup based on DT CPU frequency
With these 3 fixes in place interrupts on APE6EVM are now unbroken.
Partially based on legacy GIC fix by Geert Uytterhoeven, thanks to
him for the initial work.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Instantiate GIC from C board code in legacy builds on r8a7778 and r8a7779
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Mb4f
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-fixes2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Second Round of Renesas ARM Based SoC Fixes for v3.19" from Simon
Horman:
* Instantiate GIC from C board code in legacy builds on r8a7778 and r8a7779
* tag 'renesas-soc-fixes2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7779: Instantiate GIC from C board code in legacy builds
ARM: shmobile: r8a7778: Instantiate GIC from C board code in legacy builds
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Renesas ARM Based SoC Fixes for v3.19" from Simon Horman:
Renesas ARM Based SoC Fixes for v3.19
This pull request is based on the last round of SoC updates for v3.19,
Fourth Round of Renesas ARM Based SoC Updates for v3.19, tagged as
renesas-soc3-for-v3.19, merged into your next/soc branch and included in
v3.19-rc1.
- ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds
Set .control_parent for all irqpin instances for sh73a0 SoC when booting
using legacy C.
- ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds
This fixes a long standing problem which has been present since
the sh73a0 SoC started using the INTC External IRQ pin driver.
The patch that introduced the problem is 341eb5465f ("ARM:
shmobile: INTC External IRQ pin driver on sh73a0") which was included
in v3.10.
* tag 'renesas-soc-fixes-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: sh73a0 legacy: Set .control_parent for all irqpin instances
ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds
As of commit 9a1091ef00 ("irqchip: gic: Support hierarchy irq
domain."), Marzen legacy hangs during boot with:
Image Name: 'Linux-3.19.0-rc4'
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3445880 Bytes = 3.3 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Enabling DEBUG_LL does not seem to change the situation, however this
patch by itself fixes this issue and re-enables normal boot.
This issue happens because the IRQ numbers of the GIC are now virtual,
and no longer match the hardcoded hardware IRQ numbers in the platform
board code.
To fix this, instantiate the GIC from platform board code when compiling
a legacy kernel, like is done for the sh73a0, r8a7740 and r8a7778 legacy code.
Follows same style as the r8a7740 legacy GIC fix by Geert Uytterhoeven,
thanks to him for the initial work.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 9a1091ef00 ("irqchip: gic: Support hierarchy irq
domain."), Bock-W legacy hangs during boot with:
Unable to handle kernel paging request at virtual address cf86a128
pgd = c0004000
[cf86a128] *pgd=6f80041e(bad)
Internal error: Oops: 8000000d [#1] SMP ARM
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc4 #1
Hardware name: bockw
task: cf823b40 ti: cf824000 task.ti: cf824000
PC is at 0xcf86a128
LR is at request_threaded_irq+0xbc/0x124
This happens because the IRQ numbers of the GIC are now virtual, and no
longer match the hardcoded hardware IRQ numbers in the platform board
code.
To fix this, instantiate the GIC from platform board code when compiling
a legacy kernel, like is done for the sh73a0 and r8a7740 legacy code.
Follows same style as the r8a7740 legacy GIC fix by Geert Uytterhoeven,
thanks to him for the initial work.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a special case for PM domains containing a memory-controller.
Such a PM domain must not be turned off if memory is in use.
On sh73a0 PM domains A4BC0 and A4BC1 each contain an SDRAM Bus State
Controller (SBSC). On r8a73a4 PM domain A3BC contains two DDR Bus
Controllers (DBSC). In both cases, there are no other devices in these
PM domains, so they were eligible for power down, crashing the system.
On r8a7740 the DDR3 Bus State Controller (DBSC3) is located in A4S,
whose child domain A3SM contains the CPU core. Hence A4S is never turned
off, and no crash happened.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Make adding special PM domains to an array, and looking them up
later, more generic, so it can be used for all special hardware blocks.
The type of PM domain is also stored, so rmobile_setup_pm_domain() can
use a switch() statement instead of a chain of if/else statements.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Consolidate the identical rmobile_pd_suspend_*() routines that just
return -EBUSY to prevent a PM domain from being powered down into a
single rmobile_pd_suspend_busy().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Populate the PM domains from DT, and provide support to hook up devices
to their respective PM domain.
The always-on power area (e.g. C5 on r8a7740) is created as a PM domain
without software control, to allow Run-Time management of module clocks
for hardware blocks inside this area.
Special cases like PM domains containing CPUs, the console device, or
Coresight-ETM, are handled by scanning the DT topology.
As long as the ARM debug/perf code doesn't use resource management with
runtime PM support, the power area containing Coresight-ETM (e.g. D4 on
r8a7740) must be kept powered to avoid a crash during resume from s2ram
(dbg_cpu_pm_notify() calls reset_ctrl_regs() unconditionally, causing an
undefined instruction oops).
Initialization is done from core_initcall(), as the
"renesas,intc-irqpin" driver uses postcore_initcall().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the hardcoded addresses for accessing the SYSC PM domain
registers by register offsets, relative to the SYSC base address stored
in struct rmobile_pm_domain.
In the future, the SYSC base address will come from DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the just introduced genpd attach/detach callbacks to register the
devices' module clocks, instead of doing it directly, to make it
DT-proof.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The sh73a0 INTC can't mask interrupts properly most likely due to a
hardware bug. Set the .control_parent flag to delegate masking to the
parent interrupt controller, like was already done for irqpin1.
Without this, accessing the three-axis digital accelerometer ADXL345
on kzm9g through /dev/input/event1 causes an interrupt storm, which
requires a power-cycle to recover from.
This was inspired by a patch for arch/arm/boot/dts/sh73a0.dtsi from
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 341eb5465f ("ARM: shmobile: INTC External IRQ pin driver on sh73a0")
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Skip the TWD setup in C for r8a7779 Multiplatform.
We should use DTS for the TWD device anyway.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fix "is_e2" warning introduced by:
9ce3fa6 ARM: shmobile: rcar-gen2: Add CA7 arch_timer initialization for r8a7794
Only triggers on kernel configurations that have ARCH_ARM_TIMER=n.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This clock drives the irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
By making it available to the driver, we make sure it gets enabled when
needed, and allow it to be managed by system or runtime PM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7790 boards are now used with multiplatform kernels only. We can
remove all the unused r8a7790 legacy device and clock registration code.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Lager legacy support level is same as the DT case
so remove the legacy code and force people to move
over to using Multiplatform and DT.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
[Remove lager_defconfig and don't build the dtb for legacy kernels]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove redundant C board code for Lager Multiplatform,
everything is supported via DT these days anyway so it
is fine to rely on the MACHINE_START in setup-r8a7790.c.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
[Remove CONFIG_MACH_LAGER from shmobile_defconfig]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 9a1091ef00 ("irqchip: gic: Support hierarchy irq
domain."), armadillo-legacy hangs during boot with:
sh-tmu.0: ch0: used for clock events
sh-tmu.0: ch0: used for periodic clock events
sh-tmu.0: ch0: failed to request irq 230
sh-tmu.0: ch1: used as clock source
sh-cmt-48.1: ch0: failed to request irq 90
sh-cmt-48.1: ch0: registration failed
earlytimer: unable to probe sh-cmt-48 early.
Calibrating delay loop...
This happens because the IRQ numbers of the GIC are now virtual, and no
longer match the hardcoded hardware IRQ numbers in the platform board
code.
To fix this, instantiate the GIC from platform board code when compiling
a legacy kernel, like is done on sh73a0 for kzm9g-legacy.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull drm updates from Dave Airlie:
"Highlights:
- AMD KFD driver merge
This is the AMD HSA interface for exposing a lowlevel interface for
GPGPU use. They have an open source userspace built on top of this
interface, and the code looks as good as it was going to get out of
tree.
- Initial atomic modesetting work
The need for an atomic modesetting interface to allow userspace to
try and send a complete set of modesetting state to the driver has
arisen, and been suffering from neglect this past year. No more,
the start of the common code and changes for msm driver to use it
are in this tree. Ongoing work to get the userspace ioctl finished
and the code clean will probably wait until next kernel.
- DisplayID 1.3 and tiled monitor exposed to userspace.
Tiled monitor property is now exposed for userspace to make use of.
- Rockchip drm driver merged.
- imx gpu driver moved out of staging
Other stuff:
- core:
panel - MIPI DSI + new panels.
expose suggested x/y properties for virtual GPUs
- i915:
Initial Skylake (SKL) support
gen3/4 reset work
start of dri1/ums removal
infoframe tracking
fixes for lots of things.
- nouveau:
tegra k1 voltage support
GM204 modesetting support
GT21x memory reclocking work
- radeon:
CI dpm fixes
GPUVM improvements
Initial DPM fan control
- rcar-du:
HDMI support added
removed some support for old boards
slave encoder driver for Analog Devices adv7511
- exynos:
Exynos4415 SoC support
- msm:
a4xx gpu support
atomic helper conversion
- tegra:
iommu support
universal plane support
ganged-mode DSI support
- sti:
HDMI i2c improvements
- vmwgfx:
some late fixes.
- qxl:
use suggested x/y properties"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (969 commits)
drm: sti: fix module compilation issue
drm/i915: save/restore GMBUS freq across suspend/resume on gen4
drm: sti: correctly cleanup CRTC and planes
drm: sti: add HQVDP plane
drm: sti: add cursor plane
drm: sti: enable auxiliary CRTC
drm: sti: fix delay in VTG programming
drm: sti: prepare sti_tvout to support auxiliary crtc
drm: sti: use drm_crtc_vblank_{on/off} instead of drm_vblank_{on/off}
drm: sti: fix hdmi avi infoframe
drm: sti: remove event lock while disabling vblank
drm: sti: simplify gdp code
drm: sti: clear all mixer control
drm: sti: remove gpio for HDMI hot plug detection
drm: sti: allow to change hdmi ddc i2c adapter
drm/doc: Document drm_add_modes_noedid() usage
drm/i915: Remove '& 0xffff' from the mask given to WA_REG()
drm/i915: Invert the mask and val arguments in wa_add() and WA_REG()
drm: Zero out DRM object memory upon cleanup
drm/i915/bdw: Fix the write setting up the WIZ hashing mode
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i7gx
-----END PGP SIGNATURE-----
Merge tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Two new dvb frontend drivers: mn88472 and mn88473
- A new driver for some PCIe DVBSky cards
- A new remote controller driver: meson-ir
- One LIRC staging driver got rewritten and promoted to mainstream:
igorplugusb
- A new tuner driver (m88rs6000t)
- The old omap2 media driver got removed from staging. This driver
uses an old DMA API and it is likely broken on recent kernels.
Nobody cared enough to fix it
- Media bus format moved to a separate header, as DRM will also use the
definitions there
- mem2mem_testdev were renamed to vim2m, in order to use the same
naming convention taken by the other virtual test driver (vivid)
- Added a new driver for coda SoC (coda-jpeg)
- The cx88 driver got converted to use videobuf2 core
- Make DMABUF export buffer to work with DMA Scatter/Gather and Vmalloc
cores
- Lots of other fixes, improvements and cleanups on the drivers.
* tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (384 commits)
[media] mn88473: One function call less in mn88473_init() after error
[media] mn88473: Remove uneeded check before release_firmware()
[media] lirc_zilog: Deletion of unnecessary checks before vfree()
[media] MAINTAINERS: Add myself as img-ir maintainer
[media] img-ir: Don't set driver's module owner
[media] img-ir: Depend on METAG or MIPS or COMPILE_TEST
[media] img-ir/hw: Drop [un]register_decoder declarations
[media] img-ir/hw: Fix potential deadlock stopping timer
[media] img-ir/hw: Always read data to clear buffer
[media] redrat3: ensure dma is setup properly
[media] ddbridge: remove unneeded check before dvb_unregister_device()
[media] si2157: One function call less in si2157_init() after error
[media] tuners: remove uneeded checks before release_firmware()
[media] arm: omap2: rx51-peripherals: fix build warning
[media] stv090x: add an extra protetion against buffer overflow
[media] stv090x: Remove an unreachable code
[media] stv090x: Some whitespace cleanups
[media] em28xx: checkpatch cleanup: whitespaces/new lines cleanups
[media] si2168: add support for firmware files in new format
[media] si2168: debug printout for firmware version
...
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
* AMLogic Meson8
* ARM Realview in DT mode
* Allwinner A80
* Broadcom BCM47081
* Broadcom Cygnus
* Freescale LS1021A
* Freescale Vybrid 500 series
* Mediatek MT6592, MT8127, MT8135
* STMicroelectronics STiH410
* Samsung Exynos4415
The level of support for the above differs widely, some are just
stubs with nothing more than CPU, memory and a UART, but others
are fairly complete. As usual, these get extended over time.
There are also many new boards getting added, this is the
list of model strings that are showing up in new dts files:
* ARM RealView PB1176
* Altera SOCFPGA Arria 10
* Asus RT-N18U (BCM47081)
* Buffalo WZR-1750DHP (BCM4708)
* Buffalo WZR-600DHP2 (BCM47081)
* Cygnus Enterprise Phone (BCM911360_ENTPHN)
* D-Link DIR-665
* Google Spring
* IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
* IGEPv2 Rev. F (TI OMAP AM/DM37x)
* LS1021A QDS Board
* LS1021A TWR Board
* LeMaker Banana Pi
* MarsBoard RK3066
* MediaTek MT8127 Moose Board
* MediaTek MT8135 evaluation board
* Mele M3
* Merrii A80 Optimus Board
* Netgear R6300 V2 (BCM4708)
* Nomadik STN8815NHK
* NovaTech OrionLXm
* Olimex A20-OLinuXino-LIME2
* Raspberry Pi Model B+
* STiH410 B2120
* Samsung Monk board
* Samsung Rinato board
* Synology DS213j
* Synology DS414
* TBS2910 Matrix ARM mini PC
* TI AM5728 BeagleBoard-X15
* Toradex Colibri VF50 on Colibri Evaluation Board
* Zynq ZYBO Development Board
Other notable changes include:
* exynos: cleanup of existing dts files
* mvebu: improved pinctrl support for Armada 370/XP
* nomadik: restructuring dts files
* omap: added CAN bus support
* shmobile: added clock support for some SoCs
* shmobile: added sound support for some SoCs
* sirf: reset controller support
* sunxi: continuing the relicensing under dual GPL/MIT
* sunxi: lots of new on-chip device support
* sunxi: working simplefb support (long awaited)
* various: provide stdout-path property for earlycon
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BHwA
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Arnd Bergmann:
"The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
- AMLogic Meson8
- ARM Realview in DT mode
- Allwinner A80
- Broadcom BCM47081
- Broadcom Cygnus
- Freescale LS1021A
- Freescale Vybrid 500 series
- Mediatek MT6592, MT8127, MT8135
- STMicroelectronics STiH410
- Samsung Exynos4415
The level of support for the above differs widely, some are just stubs
with nothing more than CPU, memory and a UART, but others are fairly
complete. As usual, these get extended over time.
There are also many new boards getting added, this is the list of
model strings that are showing up in new dts files:
- ARM RealView PB1176
- Altera SOCFPGA Arria 10
- Asus RT-N18U (BCM47081)
- Buffalo WZR-1750DHP (BCM4708)
- Buffalo WZR-600DHP2 (BCM47081)
- Cygnus Enterprise Phone (BCM911360_ENTPHN)
- D-Link DIR-665
- Google Spring
- IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
- IGEPv2 Rev. F (TI OMAP AM/DM37x)
- LS1021A QDS Board
- LS1021A TWR Board
- LeMaker Banana Pi
- MarsBoard RK3066
- MediaTek MT8127 Moose Board
- MediaTek MT8135 evaluation board
- Mele M3
- Merrii A80 Optimus Board
- Netgear R6300 V2 (BCM4708)
- Nomadik STN8815NHK
- NovaTech OrionLXm
- Olimex A20-OLinuXino-LIME2
- Raspberry Pi Model B+
- STiH410 B2120
- Samsung Monk board
- Samsung Rinato board
- Synology DS213j
- Synology DS414
- TBS2910 Matrix ARM mini PC
- TI AM5728 BeagleBoard-X15
- Toradex Colibri VF50 on Colibri Evaluation Board
- Zynq ZYBO Development Board
Other notable changes include:
- exynos: cleanup of existing dts files
- mvebu: improved pinctrl support for Armada 370/XP
- nomadik: restructuring dts files
- omap: added CAN bus support
- shmobile: added clock support for some SoCs
- shmobile: added sound support for some SoCs
- sirf: reset controller support
- sunxi: continuing the relicensing under dual GPL/MIT
- sunxi: lots of new on-chip device support
- sunxi: working simplefb support (long awaited)
- various: provide stdout-path property for earlycon"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (510 commits)
ARM: dts: rk3288: add arm,cpu-registers-not-fw-configured
Revert "ARM: dts: rockchip: temporarily disable smp on rk3288"
ARM: BCM5301X: Add DT for Buffalo WZR-600DHP2
ARM: BCM5301X: Add DT for Asus RT-N18U
ARM: BCM5301X: Add DT for Buffalo WZR-1750DHP
ARM: BCM5301X: Add DT for Netgear R6300 V2
ARM: BCM5301X: Add buttons for Netgear R6250
ARM: dts: rockchip: Add input voltage supply regulators in pmic for Marsboard
ARM: BCM5301X: Add IRQs to Broadcom's bus-axi in DTS file
arm: dts: zynq: Add Digilent ZYBO board
arm: dts: zynq: Move crystal freq. to board level
doc: dt: vendor-prefixes: Add Digilent Inc
Documentation: devicetree: Fix Xilinx VDMA specification
ARM: dts: rockchip: set FIFO size for SDMMC, SDIO and EMMC on rk3066 and rk3188
ARM: dts: rockchip: add label property for leds on Radxa Rock
ARM: BCM5301X: Add LEDs for Netgear R6250 V1
ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file
ARM: dts: add sysreg phandle to i2c device nodes for exynos
ARM: dts: Remove unused bootargs from exynos3250-rinato
ARM: dts: add board dts file for Exynos3250-based Monk board
...
New and updated SoC support, notable changes include:
* bcm: brcmstb SMP support
* bcm: initial iproc/cygnus support
* exynos: Exynos4415 SoC support
* exynos: PMU and suspend support for Exynos5420
* exynos: PMU support for Exynos3250
* exynos: pm related maintenance
* imx: new LS1021A SoC support
* imx: vybrid 610 global timer support
* integrator: convert to using multiplatform configuration
* mediatek: earlyprintk support for mt8127/mt8135
* meson: meson8 soc and l2 cache controller support
* mvebu: Armada 38x CPU hotplug support
* mvebu: drop support for prerelease Armada 375 Z1 stepping
* mvebu: extended suspend support, now works on Armada 370/XP
* omap: hwmod related maintenance
* omap: prcm cleanup
* pxa: initial pxa27x DT handling
* rockchip: SMP support for rk3288
* rockchip: add cpu frequency scaling support
* shmobile: r8a7740 power domain support
* shmobile: various small restart, timer, pci apmu changes
* sunxi: Allwinner A80 (sun9i) earlyprintk support
* ux500: power domain support
Overall, a significant chunk of changes, coming mostly from
the usual suspects: omap, shmobile, samsung and mvebu, all of
which already contain a lot of platform specific code in
arch/arm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lFoH
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support, notable changes include:
- bcm:
brcmstb SMP support
initial iproc/cygnus support
- exynos:
Exynos4415 SoC support
PMU and suspend support for Exynos5420
PMU support for Exynos3250
pm related maintenance
- imx:
new LS1021A SoC support
vybrid 610 global timer support
- integrator:
convert to using multiplatform configuration
- mediatek:
earlyprintk support for mt8127/mt8135
- meson:
meson8 soc and l2 cache controller support
- mvebu:
Armada 38x CPU hotplug support
drop support for prerelease Armada 375 Z1 stepping
extended suspend support, now works on Armada 370/XP
- omap:
hwmod related maintenance
prcm cleanup
- pxa:
initial pxa27x DT handling
- rockchip:
SMP support for rk3288
add cpu frequency scaling support
- shmobile:
r8a7740 power domain support
various small restart, timer, pci apmu changes
- sunxi:
Allwinner A80 (sun9i) earlyprintk support
- ux500:
power domain support
Overall, a significant chunk of changes, coming mostly from the usual
suspects: omap, shmobile, samsung and mvebu, all of which already
contain a lot of platform specific code in arch/arm"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (187 commits)
ARM: mvebu: use the cpufreq-dt platform_data for independent clocks
soc: integrator: Add terminating entry for integrator_cm_match
ARM: mvebu: add SDRAM controller description for Armada XP
ARM: mvebu: adjust mbus controller description on Armada 370/XP
ARM: mvebu: add suspend/resume DT information for Armada XP GP
ARM: mvebu: synchronize secondary CPU clocks on resume
ARM: mvebu: make sure MMU is disabled in armada_370_xp_cpu_resume
ARM: mvebu: Armada XP GP specific suspend/resume code
ARM: mvebu: reserve the first 10 KB of each memory bank for suspend/resume
ARM: mvebu: implement suspend/resume support for Armada XP
clk: mvebu: add suspend/resume for gatable clocks
bus: mvebu-mbus: provide a mechanism to save SDRAM window configuration
bus: mvebu-mbus: suspend/resume support
clocksource: time-armada-370-xp: add suspend/resume support
irqchip: armada-370-xp: Add suspend/resume support
ARM: add lolevel debug support for asm9260
ARM: add mach-asm9260
ARM: EXYNOS: use u8 for val[] in struct exynos_pmu_conf
power: reset: imx-snvs-poweroff: add power off driver for i.mx6
ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A
...
The remaining cleanups for 3.19 are to a large part result of
devicetree conversion nearing completion on two other platforms
besides AT91:
* Like AT91, Renesas shmobile is in the process to migrate to DT and
multiplatform, but using a different approach of doing it one
SoC at a time. For 3.19, the r8a7791 platform and associated\
"Koelsch" board are considered complete and we remove the non-DT
non-multiplatform support for this.
* The ARM Versatile Express has supported DT and multiplatform
for a long time, but we have still kept the legacy board files
around, because not all drivers were fully working before. We
have finally taken the last step to remove the board files.
Other changes in this branch are preparation for the later branches
or just unrelated to the more interesting changes:
* The dts files for arm64 get moved into per-vendor directories for
a clearer structure.
* Some dead code removal (zynq, exynos, davinci, imx)
* Using pr_*() macros more consistently instead of printk(KERN_*)
in some platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Apdh
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"The remaining cleanups for 3.19 are to a large part result of
devicetree conversion nearing completion on two other platforms
besides AT91:
- Like AT91, Renesas shmobile is in the process to migrate to DT and
multiplatform, but using a different approach of doing it one SoC
at a time. For 3.19, the r8a7791 platform and associated "Koelsch"
board are considered complete and we remove the non-DT
non-multiplatform support for this.
- The ARM Versatile Express has supported DT and multiplatform for a
long time, but we have still kept the legacy board files around,
because not all drivers were fully working before. We have finally
taken the last step to remove the board files.
Other changes in this branch are preparation for the later branches or
just unrelated to the more interesting changes:
- The dts files for arm64 get moved into per-vendor directories for a
clearer structure.
- Some dead code removal (zynq, exynos, davinci, imx)
- Using pr_*() macros more consistently instead of printk(KERN_*) in
some platform code"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (71 commits)
ARM: zynq: Remove secondary_startup() declaration from header
ARM: vexpress: Enable regulator framework when MMCI is in use
ARM: vexpress: Remove non-DT code
ARM: imx: Remove unneeded .map_io initialization
ARM: dts: imx6qdl-sabresd: Fix the microphone route
ARM: imx: refactor mxc_iomux_mode()
ARM: imx: simplify clk_pllv3_prepare()
ARM: imx6q: drop unnecessary semicolon
ARM: imx: clean up machine mxc_arch_reset_init_dt reset init
ARM: dts: imx6qdl-rex: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-gw5x: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-sabresd: Use IMX6QDL_CLK_CKO define
ARM: at91: remove useless init_time for DT-only SoCs
ARM: davinci: Remove redundant casts
ARM: davinci: Use standard logging styles
ARM: shmobile: r8a7779: Spelling/grammar s/entity/identity/, s/map/mapping/
ARM: shmobile: sh7372: Spelling/grammar s/entity map/identity mapping/
ARM: shmobile: sh73a0: Spelling/grammar s/entity map/identity mapping/
ARM: EXYNOS: Remove unused static iomapping
ARM: at91: fix build breakage due to legacy board removals
...
* pm-cpuidle:
cpuidle: add MAINTAINERS entry for ARM Exynos cpuidle driver
drivers: cpuidle: Remove cpuidle-arm64 duplicate error messages
drivers: cpuidle: Add idle-state-name description to ARM idle states
drivers: cpuidle: Add status property to ARM idle states
cpuidle: Invert CPUIDLE_FLAG_TIME_VALID logic
* pm-domains:
ARM: shmobile: Convert to genpd flags for PM clocks for R-mobile
ARM: shmobile: Convert to genpd flags for PM clocks for r8a7779
PM / Domains: Initial PM clock support for genpd
PM / Domains: Power on the PM domain right after attach completes
PM / Domains: Move struct pm_domain_data to pm_domain.h
PM / Domains: Extract code to power off/on a PM domain
PM / Domains: Make genpd parameter of pm_genpd_present() const
* pm-sleep:
PM / hibernate: Deletion of an unnecessary check before the function call "vfree"
PM / Hibernate: Migrate to ktime_t
* pm-tools:
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
Instead of using the dev_ops ->stop|start() callbacks for genpd, let's
convert to use genpd's flag field and set it to GENPD_FLAG_PM_CLK.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Instead of using the dev_ops ->stop|start() callbacks for genpd, let's
convert to use genpd's flag field and set it to GENPD_FLAG_PM_CLK.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Platform data support has been removed from the DU driver, drop DU
support from the legacy Marzen board file. The multiplatform DT-based
Marzen support should be used instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Platform data support has been removed from the DU driver, drop DU
support from the legacy Lager board file. The multiplatform DT-based
Lager support should be used instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* Add early debugging support using SCIF(A)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O/9v
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc4-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Pull "Fourth Round of Renesas ARM Based SoC Updates for v3.19" from Simon Horman:
* Add early debugging support using SCIF(A)
* tag 'renesas-soc4-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Add early debugging support using SCIF(A)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Enable DU using DT on marzen/r8a7779, lager/r8a7790 and koelsch/r8a7791
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=m0Ov
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-du-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
Pull "Renesas ARM Based SoC DT DU Updates for v3.19" from Simon Horman:
* Enable DU using DT on marzen/r8a7779, lager/r8a7790 and koelsch/r8a7791
* tag 'renesas-dt-du-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: koelsch: Enable DU device in DT
ARM: shmobile: koelsch-reference: Remove DU platform device
ARM: shmobile: lager: Enable DU device in DT
ARM: shmobile: lager-reference: Remove DU platform device
ARM: shmobile: marzen: Enable DU device in DT
ARM: shmobile: dts: Add common file for AA104XD12 panel
ARM: shmobile: r8a7791: Add DU node to device tree
ARM: shmobile: r8a7790: Add DU node to device tree
ARM: shmobile: r8a7779: Add DU node to device tree
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Enable PCI domains for R-Car Gen2 devices
* Make APMU resource code SoC-specific
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=g7rn
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Pull "Second Round of Renesas ARM Based SoC Soc Updates for v3.19" from Simon Horman:
* Enable PCI domains for R-Car Gen2 devices
* Make APMU resource code SoC-specific
* tag 'renesas-soc2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Enable PCI domains for R-Car Gen2 devices
ARM: shmobile: r8a7791: Correct number of CPU cores
ARM: shmobile: Separate APMU resource data into CPU dependant part
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Select CONFIG_ZONE_DMA when CONFIG_ARM_LPAE is enabled
* Add CA7 arch_timer initialization for r8a7794
* Handle CA7 arch timer delay
* Add shmobile_init_late() to sh7372
- This is consistent with other shmobile SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bG2T
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Pull "Renesas ARM Based SoC Soc Updates for v3.19" from Simon Horman:
* Select CONFIG_ZONE_DMA when CONFIG_ARM_LPAE is enabled
* Add CA7 arch_timer initialization for r8a7794
* Handle CA7 arch timer delay
* Add shmobile_init_late() to sh7372
- This is consistent with other shmobile SoCs
* tag 'renesas-soc-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Select CONFIG_ZONE_DMA when CONFIG_ARM_LPAE is enabled
ARM: shmobile: rcar-gen2: Add CA7 arch_timer initialization for r8a7794
ARM: shmobile: sh7372: Add shmobile_init_late()
ARM: shmobile: Handle CA7 arch timer delay
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add serial port debug macros for the SCIF(A) serial ports.
This includes all supported shmobile SoCs, except for EMEV2.
The configuration logic (both Kconfig and #ifdef) is more complicated than
one would expect, for several reasons:
1. Not all SoCs have the same serial devices, and they're not always
at the same addresses.
2. There are two different types: SCIF and SCIFA. Fortunately they can
easily be distinguished by physical address.
3. Not all boards use the same serial port for the console.
The defaults correspond to the boards that are supported in
mainline. If you want to use a different serial port, just change
the value of CONFIG_DEBUG_UART_PHYS, and the rest will auto-adapt.
4. debug_ll_io_init() maps the SCIF(A) registers to a fixed virtual
address. 0xfdxxxxxx was chosen, as it should lie below VMALLOC_END
= 0xff000000, and must not conflict with the 2 MiB reserved region
at PCI_IO_VIRT_BASE = 0xfee00000.
- On SoCs not using the legacy machine_desc.map_io(),
debug_ll_io_init() is called by the ARM core code.
- On SoCs using the legacy machine_desc.map_io(),
debug_ll_io_init() must be called explicitly. Calls are added
for r8a7740, r8a7779, sh7372, and sh73a0.
This was derived from the r8a7790 version by Laurent Pinchart.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In order to have subsytem agnostic media bus format definitions we've
moved media bus definition to include/uapi/linux/media-bus-format.h and
prefixed values with MEDIA_BUS_FMT instead of V4L2_MBUS_FMT.
Reference new definitions in all platform drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The only place where the time is invalid is when the ACPI_CSTATE_FFH entry
method is not set. Otherwise for all the drivers, the time can be correctly
measured.
Instead of duplicating the CPUIDLE_FLAG_TIME_VALID flag in all the drivers
for all the states, just invert the logic by replacing it by the flag
CPUIDLE_FLAG_TIME_INVALID, hence we can set this flag only for the acpi idle
driver, remove the former flag from all the drivers and invert the logic with
this flag in the different governor.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In a combined ARMv6/v7 kernel, the setup-rcar-gen2.c cannot
currently be compiled correctly because it uses the isb
instruction that is not available on ARMv6. Adding the
-march=armv7-a flag lets the compiler know that it is safe
to build this file for ARMv7.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Port the sh73a0 restart handling from the kzm9g-legacy board code to the
generic sh73a0 code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On sh73a0/kzm9g-legacy, probing of the i2c masters fails with:
i2c-sh_mobile i2c-sh_mobile.0: timing values out of range: L/H=0x208/0x1bf
sh_mobile: probe of i2c-sh_mobile.0 failed with error -22
According to the datasheet, the transfer rate is derived from the HP
clock (which runs at 104 MHz) divided by two. Hence
i2c_sh_mobile_platform_data.clks_per_count should be set to two.
Now probing succeeds, and i2c works:
i2c-sh_mobile i2c-sh_mobile.0: I2C adapter 0 with bus speed 100000 Hz (L/H=0x104/0xe0)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Port the sh73a0 restart handling from the kzm9g-legacy board code to the
kzm9g-reference board code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to the datasheet, the operating clock for IIC0 is the HPP
(RT Peri) clock, not the SUB (Peri) clock. Both clocks run at the same
speed (50 Mhz).
This is consistent with IIC0 being located in the A4R PM domain, and
IIC1 in the A3SP PM domain.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This clock drives the irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
By making it available to the driver, we make sure it gets enabled when
needed, and allow it to be managed by system or runtime PM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PCI core will soon automatically handle the PCI domain number,
allowing the internal PCI and external PCIe bridges work at the same time.
In order for that to work, we need to enable PCI_DOMAINS.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Sort armadillo800eva includes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUUG/UAAoJENfPZGlqN0++BaYQAKCgAlWNFxVQVARtmZOSC97A
7QA/JhwG6eCbPax1dUbhoSXiUEvi3XPzxUAvlV35l1RoVZNi6uY16oXx+FWZ/JYh
f2MgP0TsiUbYJ3m25+mp2Gn8wKYIb9DTW405hffbbQn4BaQVQydNC8iqSs3zW6cV
D3lacaABqX2Gv/m8oGwb96rEHOhFsNNk8t83VutCfvmLJUvaEf4u32NT0WBftSU4
8v5xicGJDszZsu6Zxe3JEd2ol/6lUGlItTQnuD8rE7YHzOIJ3XS5q8Zj1YXrLhiT
XJ8wXA+13MFHX3+ES8YS7HxF8xZrkFAK4Oo3KvkR5RfNuQ5dtUKr+nkL/vSC9WhZ
7Woni2VHuY/SDGUMNGFoIQDmSbj3TfXpu2iDFDuHPaHatBcGyA3epMX3oCvX5RIM
xY2StQ3Avd9nioju9P5aTB9tvc6Gg2uaffaUO4t/ZclprhGozChwjmGsTYSvdpdW
/p3kjtOwX8sYNm9WAXB8RhccsbDs4m1q+nHAu4hhasjyxjjDdpi2pUf/42dljYIr
THCEvGpeLJ7OrcyD0UHcAUUAn0ULZofswBjYRak8RCfJ8TvjKL3EQtX+h1TfVWBF
4JQ65HM811vEHWQHhPhGS2MkVzOT33G6pjB4n2lm5ZPWZYs8ERO3uwrU1Ty4kHLf
9+f2ipE510nuvAh0a3ei
=sMXS
-----END PGP SIGNATURE-----
Merge tag 'renesas-boards-cleanups-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
Merge "Renesas ARM Based SoC Boards Cleanups for v3.19" from Simon Horman:
* Sort armadillo800eva includes
* tag 'renesas-boards-cleanups-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: armadillo800eva: Sort includes
Signed-off-by: Olof Johansson <olof@lixom.net>
The r8a7791 only has 2 CPU CA15 cores, not 4 CA15 and 4 CA7 cores.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
APMU resources are not common to all R-Car SoCs so don't share this data.
A subsequent patch will correct the CPU cores for the r8a7791.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Koelsch board is supported by the r8a7791 generic DT platform
definition. Remove the board-specific definition along with its board
file.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7791 boards are now used with multiplatform kernels only. We can
remove all the unused r8a7791 legacy device and clock registration code.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All features supported by the Koelsch legacy C board code are now
supported by the multiplatform code, it's thus time to say bye to the
legacy code. Nobody should miss it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The function isn't used or needed anymore, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Initialise TMU device using DT when booting bockw
using DT-reference.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The marzen-reference board file doesn't need the clock.h header, don't
include it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU device is now instantiated from the device tree, remove the
corresponding platform device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU device is now instantiated from the device tree, remove the
corresponding platform device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Most IP cores on ARM Renesas platforms can only address 32 bits of
physical memory for DMA. Without CONFIG_ZONE_DMA enabled and with the
recent CMA highmem allocation support, the default CMA zone is reserved
above the 4GiB limit when LPAE is enabled, resulting in various driver
failures.
Fix the problem by selecting CONFIG_ZONE_DMA. Other options to
investigate in the future would be to either enable IOMMU support or use
custom CMA reservations for peripherals not supporting LPAE.
While not a strict dependency, the "[PATCH 0/4] Low/high memory CMA
reservation fixes" series is also required to fix a different but related CMA
allocation problem.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the A3SM power domain, and hook it up as a subdomain of
A4S.
This domain contains the System CPU (Cortex-A9) hardware block. Hence
move the special CPU handling from A4S to A3SM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the A4SU power domain.
This domain contains the USBPHY hardware block, which is currently not
used by any driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the A4R power domain, and hook up the A3RV subdomain,
and the CEU0, TMU0, and IIC0 hardware blocks.
This domain also contains the Realtime CPU (SH-4A), Realtime CPU debug
modules, H-UDI, RT-SHwy, INTCS, RT-HPB, VIO6C, JPU, RTDMAC1/2, SSP,
MSIOF0, CMT0, ICB, DREQPAK (RT), 2DDMAC, IPMMUI, and 2DG hardware
blocks, but these are currently not used by any driver.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the D4 power domain.
This domain contains the Coresight-ETM hardware block.
As long as the ARM debug/perf code doesn't use resource management with
runtime PM support, the D4 power domain must be kept powered to avoid a
crash during resume from s2ram (dbg_cpu_pm_notify() calls
reset_ctrl_regs() unconditionally, causing an undefined instruction
oops).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the A4MP power domain, and hook up the HDMI-Link and FSI
hardware blocks.
This domain also contains the SPU2, FMSI, and BBIF2 hardware blocks,
but these are currently not used by any driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the A3SG power domain, and hook it up as a subdomain of
A4S.
This domain contains the SGX540 hardware block, which is currently not
used by any driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the A3RV power domain.
This domain contains the VPU5F and VCP1 hardware blocks, which are
currently not used by any driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 8459293c27 ("ARM: shmobile: r8a7740: add A4S pm domain
support") added the A4S power domain, but forgot to hook up the GbEther
hardware block.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 802a5639aa ("ARM: shmobile: r8a7740: add A3SP pm domain
support") added the A3SP power domain, but forgot to hook up the TPU,
SDHI0/1, and MMCIF hardware blocks.
Note: As the default PM QoS latency constraint for SDHI is only 100 µs
(cfr. commit c419e611c3 ("tmio_mmc / PM: Use PM QoS latency
constraint"), while DEFAULT_DEV_LATENCY_NS is 250000, suspend fails with
-EBUSY, unless the constraint is increased first to more than 500 µs
using e.g.
echo 501 > /sys/devices/platform/sh_mobile_sdhi.0/power/pm_qos_resume_latency_us
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 8459293c27 ("ARM: shmobile: r8a7740: add A4S pm domain
support") added the A4S power domain, but forgot to hook up the INTCA
hardware block.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 802a5639aa ("ARM: shmobile: r8a7740: add A3SP pm domain
support") added the A3SP power domain, but forgot to hook up the IPPMU,
DMAC0/1/2, and USBDMAC hardware blocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The information is already included in the COPYING file in the kernel
sources root directory, we don't want to modify all source files when
the FSF will move to a new address, and I'm tired of seeing the related
checkpatch.pl warnings.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On E2, the arch timer is hooked up to a different clock, and the CA7's arch
timer CNTVOFF register must be initialized.
Based on work by Hisashi Nakamura.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
sh73a0_init_delay() just calls shmobile_init_delay(), hence replace
calls to it by direct calls to shmobile_init_delay().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
r8a7778_init_delay() just calls shmobile_init_delay(), hence replace
calls to it by direct calls to shmobile_init_delay().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Rename r8a7790_register_cmt() as r8a73a4_register_cmt() to
reflect name of the SoC in use. The use of r8a7790 appears
to be due to historical sharing of code from that SoC.
Shared code is no longer used.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Extend sh7372 SoC machine vector to include shmobile_init_late()
so Suspend-to-RAM and CPUIdle are setup as expected.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the delay code to include arch timer checks
for CA7. From a arch timer availability perspective
CA7 should be treated same as CA15.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Kconfig symbol ARCH_HAS_OPP became redundant in v3.16: commit
049d595a4d ("PM / OPP: Make OPP invisible to users in Kconfig")
removed the only dependency that used it. Setting it had no effect
anymore.
So commit 78c5e0bb14 ("PM / OPP: Remove ARCH_HAS_OPP") removed it. For
some reason that commit did not remove all select statements for that
symbol. These statements are now useless. Remove one from shmobile too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull drm updates from Dave Airlie:
"This is the main git pull for the drm,
I pretty much froze major pulls at -rc5/6 time, and haven't had much
fallout, so will probably continue doing that.
Lots of changes all over, big internal header cleanup to make it clear
drm features are legacy things and what are things that modern KMS
drivers should be using. Also big move to use the new generic fences
in all the TTM drivers.
core:
atomic prep work,
vblank rework changes, allows immediate vblank disables
major header reworking and cleanups to better delinate legacy
interfaces from what KMS drivers should be using.
cursor planes locking fixes
ttm:
move to generic fences (affects all TTM drivers)
ppc64 caching fixes
radeon:
userptr support,
uvd for old asics,
reset rework for fence changes
better buffer placement changes,
dpm feature enablement
hdmi audio support fixes
intel:
Cherryview work,
180 degree rotation,
skylake prep work,
execlist command submission
full ppgtt prep work
cursor improvements
edid caching,
vdd handling improvements
nouveau:
fence reworking
kepler memory clock work
gt21x clock work
fan control improvements
hdmi infoframe fixes
DP audio
ast:
ppc64 fixes
caching fix
rcar:
rcar-du DT support
ipuv3:
prep work for capture support
msm:
LVDS support for mdp4, new panel, gpu refactoring
exynos:
exynos3250 SoC support, drop bad mmap interface,
mipi dsi changes, and component match support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (640 commits)
drm/mst: rework payload table allocation to conform better.
drm/ast: Fix HW cursor image
drm/radeon/kv: add uvd/vce info to dpm debugfs output
drm/radeon/ci: add uvd/vce info to dpm debugfs output
drm/radeon: export reservation_object from dmabuf to ttm
drm/radeon: cope with foreign fences inside the reservation object
drm/radeon: cope with foreign fences inside display
drm/core: use helper to check driver features
drm/radeon/cik: write gfx ucode version to ucode addr reg
drm/radeon/si: print full CS when we hit a packet 0
drm/radeon: remove unecessary includes
drm/radeon/combios: declare legacy_connector_convert as static
drm/radeon/atombios: declare connector convert tables as static
drm/radeon: drop btc_get_max_clock_from_voltage_dependency_table
drm/radeon/dpm: drop clk/voltage dependency filters for BTC
drm/radeon/dpm: drop clk/voltage dependency filters for CI
drm/radeon/dpm: drop clk/voltage dependency filters for SI
drm/radeon/dpm: drop clk/voltage dependency filters for NI
drm/radeon: disable audio when we disable hdmi (v2)
drm/radeon: split audio enable between eg and r600 (v2)
...
- Fix SDIO IRQ bug.
- MMC regulator improvements.
- Fix slot-gpio card detect bug.
- Add support for Driver Stage Register.
- Convert the common MMC OF parser to use GPIO descriptors.
- Convert MMC_CAP2_NO_MULTI_READ into a callback, ->multi_io_quirk().
- Some additional minor fixes.
MMC host:
- mmci: Support Qualcomm specific DML layer for DMA.
- dw_mmc: Use common MMC regulators.
- dw_mmc: Add support for Rock-chips RK3288.
- tmio: Enable runtime PM support.
- tmio: Add support for R-Car Gen2 SoCs.
- tmio: Several fixes and improvements.
- omap_hsmmc: Removed Balaji from MAINTAINERS.
- jz4740: add DMA and pre/post support.
- sdhci: Add support for Intel Braswell.
- sdhci: Several fixes and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VFRY
-----END PGP SIGNATURE-----
Merge tag 'mmc-v3.18-1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Fix SDIO IRQ bug
- MMC regulator improvements
- Fix slot-gpio card detect bug
- Add support for Driver Stage Register
- Convert the common MMC OF parser to use GPIO descriptors
- Convert MMC_CAP2_NO_MULTI_READ into a callback, ->multi_io_quirk()
- Some additional minor fixes
MMC host:
- mmci: Support Qualcomm specific DML layer for DMA
- dw_mmc: Use common MMC regulators
- dw_mmc: Add support for Rock-chips RK3288
- tmio: Enable runtime PM support
- tmio: Add support for R-Car Gen2 SoCs
- tmio: Several fixes and improvements
- omap_hsmmc: Removed Balaji from MAINTAINERS
- jz4740: add DMA and pre/post support
- sdhci: Add support for Intel Braswell
- sdhci: Several fixes and improvements"
* tag 'mmc-v3.18-1' of git://git.linaro.org/people/ulf.hansson/mmc: (119 commits)
ARM: dts: fix MMC2 regulators for Exynos5420 Arndale Octa board
mmc: sdhci-acpi: Fix Braswell eMMC timeout clock frequency
mmc: sdhci-acpi: Pass HID and UID to probe_slot
mmc: sdhci-acpi: Get UID directly from acpi_device
mmc, sdhci, bcm-kona, LLVMLinux: Remove use of __initconst
mmc: sdhci-pci: Fix Braswell eMMC timeout clock frequency
mmc: sdhci: Let a driver override timeout clock frequency
mmc: sdhci-pci: Add Bay Trail and Braswell SD card detect
mmc: sdhci-pci: Set SDHCI_QUIRK2_STOP_WITH_TC for Intel BYT host controllers
mmc: sdhci-acpi: Add a HID and UID for a SD Card host controller
mmc: sdhci-acpi: Set SDHCI_QUIRK2_STOP_WITH_TC for Intel host controllers
mmc: sdhci: Add quirk for always getting TC with stop cmd
mmc: core: restore detect line inversion semantics
mmc: Fix incorrect warning when setting 0 Hz via debugfs
mmc: Fix use of wrong device in mmc_gpiod_free_cd()
mmc: atmel-mci: fix mismatched section on atmci_cleanup_slot
mmc: rtsx_pci: Set power related cap2 macros
mmc: core: Add new power_mode MMC_POWER_UNDEFINED
mmc: sdhci: execute tuning when device is not busy
mmc: atmel-mci: Release mmc resources on failure in probe
..
- Rework the handling of wakeup IRQs by the IRQ core such that
all of them will be switched over to "wakeup" mode in
suspend_device_irqs() and in that mode the first interrupt
will abort system suspend in progress or wake up the system
if already in suspend-to-idle (or equivalent) without executing
any interrupt handlers. Among other things that eliminates the
wakeup-related motivation to use the IRQF_NO_SUSPEND interrupt
flag with interrupts which don't really need it and should not
use it (Thomas Gleixner and Rafael J Wysocki).
- Switch over ACPI to handling wakeup interrupts with the help
of the new mechanism introduced by the above IRQ core rework
(Rafael J Wysocki).
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during
enumeration (Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in
the METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot
(or after resume from system suspend) and rework the ACPI Smart
Battery Subsystem (SBS) driver to work correctly with Apple
platforms (Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the
code, adding support for 133MHz I2C source clock on Intel Baytrail
to it and making it avoid using UART RTS override with Auto Flow
Control (Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak).
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin).
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui).
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes).
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name
change among other things), ppc-corenet, powernv (Viresh Kumar,
Preeti U Murthy, Shilpasri G Bhat, Lucas Stach).
- cpuidle support for DT-based idle states infrastructure, new
ARM64 cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi,
Rasmus Villemoes).
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman).
- Rework of the test_suspend kernel command line argument and
a new trace event for console resume (Srinivas Pandruvada,
Todd E Brandt).
- Second attempt to optimize swsusp_free() (hibernation core) to
make it avoid going through all PFNs which may be way too slow on
some systems (Joerg Roedel).
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS
entry update in MAINTAINERS (Heiko Stübner, Kevin Hilman).
- PM core fix related to clock management (Geert Uytterhoeven).
- PM core's sysfs code cleanup (Johannes Berg).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=sIv/
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"Features-wise, to me the most important this time is a rework of
wakeup interrupts handling in the core that makes them work
consistently across all of the available sleep states, including
suspend-to-idle. Many thanks to Thomas Gleixner for his help with
this work.
Second is an update of the generic PM domains code that has been in
need of some care for quite a while. Unused code is being removed, DT
support is being added and domains are now going to be attached to
devices in bus type code in analogy with the ACPI PM domain. The
majority of work here was done by Ulf Hansson who also has been the
most active developer this time.
Apart from this we have a traditional ACPICA update, this time to
upstream version 20140828 and a few ACPI wakeup interrupts handling
patches on top of the general rework mentioned above. There also are
several cpufreq commits including renaming the cpufreq-cpu0 driver to
cpufreq-dt, as this is what implements generic DT-based cpufreq
support, and a new DT-based idle states infrastructure for cpuidle.
In addition to that, the ACPI LPSS driver is updated, ACPI support for
Apple machines is improved, a few bugs are fixed and a few cleanups
are made all over.
Finally, the Adaptive Voltage Scaling (AVS) subsystem now has a tree
maintained by Kevin Hilman that will be merged through the PM tree.
Numbers-wise, the generic PM domains update takes the lead this time
with 32 non-merge commits, second is cpufreq (15 commits) and the 3rd
place goes to the wakeup interrupts handling rework (13 commits).
Specifics:
- Rework the handling of wakeup IRQs by the IRQ core such that all of
them will be switched over to "wakeup" mode in suspend_device_irqs()
and in that mode the first interrupt will abort system suspend in
progress or wake up the system if already in suspend-to-idle (or
equivalent) without executing any interrupt handlers. Among other
things that eliminates the wakeup-related motivation to use the
IRQF_NO_SUSPEND interrupt flag with interrupts which don't really
need it and should not use it (Thomas Gleixner and Rafael Wysocki)
- Switch over ACPI to handling wakeup interrupts with the help of the
new mechanism introduced by the above IRQ core rework (Rafael Wysocki)
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during enumeration
(Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in the
METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot (or
after resume from system suspend) and rework the ACPI Smart Battery
Subsystem (SBS) driver to work correctly with Apple platforms
(Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the code,
adding support for 133MHz I2C source clock on Intel Baytrail to it
and making it avoid using UART RTS override with Auto Flow Control
(Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak)
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin)
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui)
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes)
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name change
among other things), ppc-corenet, powernv (Viresh Kumar, Preeti U
Murthy, Shilpasri G Bhat, Lucas Stach)
- cpuidle support for DT-based idle states infrastructure, new ARM64
cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi, Rasmus
Villemoes)
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman)
- Rework of the test_suspend kernel command line argument and a new
trace event for console resume (Srinivas Pandruvada, Todd E Brandt)
- Second attempt to optimize swsusp_free() (hibernation core) to make
it avoid going through all PFNs which may be way too slow on some
systems (Joerg Roedel)
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS entry
update in MAINTAINERS (Heiko Stübner, Kevin Hilman)
- PM core fix related to clock management (Geert Uytterhoeven)
- PM core's sysfs code cleanup (Johannes Berg)"
* tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (105 commits)
ACPI / fan: printk replacement
PM / clk: Fix crash in clocks management code if !CONFIG_PM_RUNTIME
PM / Domains: Rename cpu_data to cpuidle_data
cpufreq: cpufreq-dt: fix potential double put of cpu OF node
cpufreq: cpu0: rename driver and internals to 'cpufreq_dt'
PM / hibernate: Iterate over set bits instead of PFNs in swsusp_free()
cpufreq: ppc-corenet: remove duplicate update of cpu_data
ACPI / sleep: Rework the handling of ACPI GPE wakeup from suspend-to-idle
PM / sleep: Rename platform suspend/resume functions in suspend.c
PM / sleep: Export dpm_suspend_late/noirq() and dpm_resume_early/noirq()
ACPICA: Introduce acpi_enable_all_wakeup_gpes()
ACPICA: Clear all non-wakeup GPEs in acpi_hw_enable_wakeup_gpe_block()
ACPI / video: check _DOD list when creating backlight devices
PM / Domains: Move dev_pm_domain_attach|detach() to pm_domain.h
cpufreq: Replace strnicmp with strncasecmp
cpufreq: powernv: Set the cpus to nominal frequency during reboot/kexec
cpufreq: powernv: Set the pstate of the last hotplugged out cpu in policy->cpus to minimum
cpufreq: Allow stop CPU callback to be used by all cpufreq drivers
PM / devfreq: exynos: Enable building exynos PPMU as module
PM / devfreq: Export helper functions for drivers
...
New and updated SoC support. Among the things new for this release are:
- at91: Added support for the new SAMA5D4 SoC, following the earlier SAMA5D3
- bcm: Added support for BCM63XX family of DSL SoCs
- hisi: Added support for HiP04 server-class SoC
- meson: Initial support for the Amlogic Meson6 (aka 8726MX) platform
- shmobile: added support for new r8a7794 (R-Car E2) automotive SoC
Noteworthy changes to existing SoC support are:
- imx: convert i.MX1 to device tree
- omap: lots of power management work
- omap: base support to enable moving to standard UART driver
- shmobile: lots of progress for multiplatform support, still ongoing
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ZHtj
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support. Among the things new for this release
are:
- at91: Added support for the new SAMA5D4 SoC, following the earlier
SAMA5D3
- bcm: Added support for BCM63XX family of DSL SoCs
- hisi: Added support for HiP04 server-class SoC
- meson: Initial support for the Amlogic Meson6 (aka 8726MX) platform
- shmobile: added support for new r8a7794 (R-Car E2) automotive SoC
Noteworthy changes to existing SoC support are:
- imx: convert i.MX1 to device tree
- omap: lots of power management work
- omap: base support to enable moving to standard UART driver
- shmobile: lots of progress for multiplatform support, still
ongoing"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (171 commits)
ARM: hisi: depend on ARCH_MULTI_V7
CNS3xxx: Fix debug UART.
ARM: at91: fix nommu build regression
ARM: meson: add basic support for MesonX SoCs
ARM: meson: debug: add debug UART for earlyprintk support
irq: Export handle_fasteoi_irq
ARM: mediatek: Add earlyprintk support for mt6589
ARM: hisi: Fix platmcpm compilation when ARMv6 is selected
ARM: debug: fix alphanumerical order on debug uarts
ARM: at91: document Atmel SMART compatibles
ARM: at91: add sama5d4 support to sama5_defconfig
ARM: at91: dt: add device tree file for SAMA5D4ek board
ARM: at91: dt: add device tree file for SAMA5D4 SoC
ARM: at91: SAMA5D4 SoC detection code and low level routines
ARM: at91: introduce basic SAMA5D4 support
clk: at91: add a driver for the h32mx clock
ARM: pxa3xx: provide specific platform_devices for all ssp ports
ARM: pxa: ssp: provide platform_device_id for PXA3xx
ARM: OMAP4+: Remove static iotable mappings for SRAM
ARM: OMAP4+: Move SRAM data to DT
...
* pm-cpufreq:
cpufreq: cpufreq-dt: fix potential double put of cpu OF node
cpufreq: cpu0: rename driver and internals to 'cpufreq_dt'
cpufreq: ppc-corenet: remove duplicate update of cpu_data
cpufreq: Replace strnicmp with strncasecmp
cpufreq: powernv: Set the cpus to nominal frequency during reboot/kexec
cpufreq: powernv: Set the pstate of the last hotplugged out cpu in policy->cpus to minimum
cpufreq: Allow stop CPU callback to be used by all cpufreq drivers
cpufreq: cpu0: Make allocate_resources() work for any CPU
cpufreq: cpu0: try regulators with name "cpu-supply"
cpufreq: cpu0: Move per-cluster initialization code to ->init()
cpufreq: cpu0: use dev_{err|warn|dbg} instead of pr_{err|warn|debug}
cpufreq: cpu0: print relevant error when we defer probe
cpufreq: cpu0: don't validate clock on clk_put()
cpufreq: cpu0: Update Module Author
cpufreq: Add support for per-policy driver data
The naming convention of this driver was always under the scanner, people
complained that it should have a more generic name than cpu0, as it manages all
CPUs that are sharing clock lines.
Also, in future it will be modified to support any number of clusters with
separate clock/voltage lines.
Lets rename it to 'cpufreq_dt' from 'cpufreq_cpu0'.
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* r8a7740: Fix documentation error coppied from elsewhere
* r8a7794: Reserve memory for CMA in a manner consistent to
other R-Car Gen2 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUG61hAAoJENfPZGlqN0++YrEP/2AUMZCOUlKOz71JMS9d26vD
g64wXv8SEezY+RwBnxO2CNNPGUQf+3RjGNIyEhE62PbF7y6RcDz6sFxhR7FKrnf4
aDFC/fyh2jot3lsPmEv8fBH94FkmAao/dyO6nAlaJ64ACGDoApecWlL3KFBG6i7a
QRB3e+tRetGEHQsdlwLrap8SJN0YigkjFKorOVHEAHnQlNnULCRYcGgJo742jGyr
6IEiZUGn5OOWWRtiTWs1oWQbMsnbHmgG4l6/51NKkuD/uoxq7gMbBiHu9ht5npmo
e5zPQ+1ILA9hI43Mk52vfilNXdBn7urTjc6CtROXWBer35smJ5kpxj5WSKpT7jTN
MXENqilQiYeTbP5GR3p96p4JiL2U3Zd+frxfsPOMgyfvTGEdYFULfuXgblgwEGv2
RC/8AB8lfcnwPnkI1C21GR2Zbt7bw8ytJD9iQoTb1GEqyVMd/Oxrp0S+/Zk9EoVW
w+3fCRJrBQVmTDi9XArqt5IgpjloZndfkwVX6J45/KJu4/gFCv1AKYSw7bD/rNrD
cZzDYtkj9DbO125gDDfyJo+jMOMJGVUnHv9XSLgBpUbaEKfa9oh2hpwPoM0C/OS5
KHMISR2rFu4vVteLlANLODSFoprM1Xyd4NDFqp5bdwN7RoMZFLOHHwlzmMXn/Xc8
lladCk6BwpEkOUYYriG3
=wfDI
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc5-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Pull "Fifth Round of Renesas ARM Based SoC Soc Updates for v3.18" from Simon Horman:
* r8a7740: Fix documentation error copied from elsewhere
* r8a7794: Reserve memory for CMA in a manner consistent to
other R-Car Gen2 SoCs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'renesas-soc5-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7740 legacy: Fix copied bug in comment
ARM: shmobile: r8a7794: Reserve memory as other R-Car Gen2 SoCs
- PM changes to make the code easier to use on newer SoCs
- PM changes for newer SoCs suspend and resume and wake-up events
- Minor clean-up to remove dead Kconfig options
Note that these have a dependency to the fixes-v3.18-not-urgent
tag and is based on a commit in that series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LW8C
-----END PGP SIGNATURE-----
Merge tag 'soc-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
SoC related changes for omaps for v3.18 merge window:
- PM changes to make the code easier to use on newer SoCs
- PM changes for newer SoCs suspend and resume and wake-up events
- Minor clean-up to remove dead Kconfig options
Note that these have a dependency to the fixes-v3.18-not-urgent
tag and is based on a commit in that series.
* tag 'soc-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (514 commits)
ARM: OMAP5+: Reuse OMAP4 PM code for OMAP5 and DRA7
ARM: dts: OMAP3+: Add PRM interrupt
ARM: omap: Remove stray ARCH_HAS_OPP references
ARM: DRA7: Add hook in SoC initcalls to enable pm initialization
ARM: OMAP5: Add hook in SoC initcalls to enable pm initialization
ARM: OMAP5 / DRA7: Enable CPU RET on suspend
ARM: OMAP5 / DRA7: PM: Provide a dummy startup function for CPU hotplug
ARM: OMAP5 / DRA7: PM: Avoid all SAR saves
ARM: OMAP5 / DRA7: PM: Enable Mercury retention mode on CPUx powerdomains
ARM: OMAP5 / DRA7: PM / wakeupgen: Enables ES2 PM mode by default
ARM: OMAP5 / DRA7: PM: Set MPUSS-EMIF clock-domain static dependency
ARM: OMAP5 / DRA7: PM: Update CPU context register offset
ARM: AM437x: use pdata quirks for pinctrl information
ARM: DRA7: use pdata quirks for pinctrl information
ARM: OMAP5: use pdata quirks for pinctrl information
ARM: OMAP4+: PM: Use only valid low power state for CPU hotplug
ARM: OMAP4+: PM: use only valid low power state for suspend
ARM: OMAP4+: PM: Make logic state programmable
ARM: OMAP2+: powerdomain: introduce logic for finding valid power domain
ARM: OMAP2+: powerdomain: pwrdm_for_each_clkdm iterate only valid clkdms
...
Commit "drm/rcar-du: Use struct videomode in platform data" touches board code
in arch/arm/mach-shmobile. There is, to the best of my knowledge, no risk of
conflict for v3.18. Simon, are you fine with getting those changes merged
through Dave's tree (and could you confirm that no conflict should occur) ?
Simon acked the merge:
Acked-by: Simon Horman <horms+renesas@verge.net.au>
* 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev:
drm/rcar-du: Add OF support
drm/rcar-du: Use struct videomode in platform data
video: Add DT bindings for the R-Car Display Unit
video: Add THC63LVDM83D DT bindings documentation
video: Add ADV7123 DT bindings documentation
video: Add DT binding documentation for VGA connector
devicetree: Add vendor prefix "thine" to vendor-prefixes.txt
devicetree: Add vendor prefix "mitsubishi" to vendor-prefixes.txt
drm/shmob: Update copyright notice
drm/rcar-du: Update copyright notice
The corresponding bug in pm-sh7372.c was fixed in commit
70fe7b2467 ("ARM: shmobile: Do not access sh7372 A4S domain
internals directly").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Other R-Car Gen2 SoCs such as r8a7790 and r8a7791 reserve
the top 256 MiB of memory for use with CMA. Adjust the
board-less r8a7794 code to do the same.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In preparation for DT support where panel timings will be described by a
DRM-agnostic video mode, replace the struct drm_mode_modeinfo instance
in the panel platform data with a struct videomode.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
* Make domain_devices[] static __initdata
* Add and use rmobile_add_devices_to_domain
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5GhR
-----END PGP SIGNATURE-----
Merge tag 'renesas-pm-cleanups-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
Pull "Renesas ARM Based SoC PM Cleanups for v3.18" from Simon Horman:
* Make domain_devices[] static __initdata
* Add and use rmobile_add_devices_to_domain
Signed-off-by: Arnd Bergmann <ardn@arndb.de>
* tag 'renesas-pm-cleanups-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: armadillo800eva legacy: Use rmobile_add_devices_to_domains()
ARM: shmobile: r8a7740: Clean up pm domain table
ARM: shmobile: r8a7740: Use rmobile_add_devices_to_domains()
ARM: shmobile: sh7372: Make domain_devices[] static __initdata
ARM: shmobile: mackerel: Make domain_devices[] static __initdata
The r8a7794 support is always compiled using ARCH_MULTIPLATFORM which
selects USE_OF. So #ifdef CONFIG_USE_OF is unnecessary.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Initial r8a7794 SoC support
* Support Cortex-A7 in shmobile_init_delay()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iaYv
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc3-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Pull "Third Round of Renesas ARM Based SoC Soc Updates for v3.18" from Simon Horman:
* Initial r8a7794 SoC support
* Support Cortex-A7 in shmobile_init_delay()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'renesas-soc3-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Initial r8a7794 SoC support
ARM: shmobile: support Cortex-A7 in shmobile_init_delay()
When booting using the r8a7740/armadillo800eva using dt-reference:
* Use CCF to initialise clocks via DT
* Initialise timers via DT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT/BT6AAoJENfPZGlqN0++MPwQAIzGfi79jMY14Xep790KD17A
wvae1QGyLpIPH/nyVr6iEbHiX3YBfW4kcvrQ1GWOG19tFoWlc4fiOK1ZcCAnydFD
SU1lnkpT6+ZIEeFkdXwMyux2lVeaZSQHOInT7UYZnWLUhfkCkuf7IJNvrYNMGb+Z
3viXbRkqz1cz9nyIRDmryq0IZO8d7ZNFhOSdTTq3Rjzn32V68I2HZVGKOu00bI7J
UEpEXlPqAs8R90NkyLvoEaN3d0NHz6TrX8VqgWW6cNxu8Kv3OCLhkjmGdjmWXZ3P
SuVXJv37vcjkKXuclRVaPV8GcQgJZO34RSUpc0HMYJyutEp3ANLxujT7zFSwJEvK
vUZkPGpzWY9+icqfPOoGlEoGIcVGTnB1rH25ap5y/b7SnfNsw2dJyhx/Mr8nln2b
SwTMXxZZvP8V2qK7CrXU5TXnhl2nYJwvjU8ORhe3ZJrAOmrlfrBNFBTzm/8Txik7
/JUFjInTkOoLX4a0vjJlwc/rRAAe8jASmpWTC6N9mTzJhY7gySpXwxWOwT2f/+YR
otDz1JS4EpqRFiK3ptnPVJ7sVpamz5glCLCCZWMZdwWG7G1B+daXD2shTPk7aup5
EsN0YKIjMfdTL5sQcQIhS5Yoj/KJEhwkNny+EsMofExKZeQerqQT3SG9a798xxLR
8ACepiF2VECSLNCWvUKj
=uu7K
-----END PGP SIGNATURE-----
Merge tag 'renesas-r8a7740-ccf-and-timers-for-v3.18' into dt-timers-for-v3.18
Renesas ARM Based SoC R8a7740 CCF and Timers Updates for v3.18
When booting using the r8a7740/armadillo800eva using dt-reference:
* Use CCF to initialise clocks via DT
* Initialise timers via DT
Use a table and the rmobile_add_devices_to_domains() helper function to
add all platform devices to their power domains at once, which is more
size-efficient than calling rmobile_add_device_to_domain() explicitly
for all devices individually.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- Sort pm domains by bit_shift value,
- Combine closing and opening curly braces on a single line, as the
table will grow much bigger soon.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use a table and the rmobile_add_devices_to_domains() helper function to
add all platform devices to their power domains at once, which is more
size-efficient than calling rmobile_add_device_to_domain() explicitly
for all devices individually.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Make the domain_devices[] array static and __initdata, to reduce kernel
size:
- Making it static gets rid of the code to copy the data to the stack,
- Marking it __initdata allows more init memory to be freed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Make the domain_devices[] array static and __initdata, to reduce kernel
size:
- Making it static gets rid of the code to copy the data to the stack,
- Marking it __initdata allows more init memory to be freed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The dev_irq_safe configuration is redundant, genpd don't have any
special treatmeant for handling it. Let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The dev_irq_safe configuration is redundant, genpd don't have any
special treatmeant for handling it. Let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* Enable timers using DT when booting boards without Legacy-C code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cyP9
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-timers-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Renesas ARM Based SoC DT Timers Updates for v3.18" from Simon Horman:
* Enable timers using DT when booting boards without Legacy-C code
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'renesas-dt-timers-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: genmai-reference: Enable MTU2 in device tree
ARM: shmobile: r7s72100: Add MTU2 device to DT
ARM: shmobile: marzen-reference: Enable TMU0 in device tree
ARM: shmobile: koelsch-reference: Enable CMT0 in device tree
ARM: shmobile: lager-reference: Enable CMT0 in device tree
ARM: shmobile: r8a7779: Add TMU devices to DT
ARM: shmobile: r8a7791: Add CMT devices to DT
ARM: shmobile: r8a7790: Add CMT devices to DT
Conflicts:
arch/arm/mach-shmobile/setup-r8a7779.c
When booting using the r8a7740/armadillo800eva using dt-reference:
* Use CCF to initialise clocks via DT
* Initialise timers via DT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT/BT6AAoJENfPZGlqN0++MPwQAIzGfi79jMY14Xep790KD17A
wvae1QGyLpIPH/nyVr6iEbHiX3YBfW4kcvrQ1GWOG19tFoWlc4fiOK1ZcCAnydFD
SU1lnkpT6+ZIEeFkdXwMyux2lVeaZSQHOInT7UYZnWLUhfkCkuf7IJNvrYNMGb+Z
3viXbRkqz1cz9nyIRDmryq0IZO8d7ZNFhOSdTTq3Rjzn32V68I2HZVGKOu00bI7J
UEpEXlPqAs8R90NkyLvoEaN3d0NHz6TrX8VqgWW6cNxu8Kv3OCLhkjmGdjmWXZ3P
SuVXJv37vcjkKXuclRVaPV8GcQgJZO34RSUpc0HMYJyutEp3ANLxujT7zFSwJEvK
vUZkPGpzWY9+icqfPOoGlEoGIcVGTnB1rH25ap5y/b7SnfNsw2dJyhx/Mr8nln2b
SwTMXxZZvP8V2qK7CrXU5TXnhl2nYJwvjU8ORhe3ZJrAOmrlfrBNFBTzm/8Txik7
/JUFjInTkOoLX4a0vjJlwc/rRAAe8jASmpWTC6N9mTzJhY7gySpXwxWOwT2f/+YR
otDz1JS4EpqRFiK3ptnPVJ7sVpamz5glCLCCZWMZdwWG7G1B+daXD2shTPk7aup5
EsN0YKIjMfdTL5sQcQIhS5Yoj/KJEhwkNny+EsMofExKZeQerqQT3SG9a798xxLR
8ACepiF2VECSLNCWvUKj
=uu7K
-----END PGP SIGNATURE-----
Merge tag 'renesas-r8a7740-ccf-and-timers-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Renesas ARM Based SoC R8a7740 CCF and Timers Updates for v3.18" from Simon Horman:
When booting using the r8a7740/armadillo800eva using dt-reference:
* Use CCF to initialise clocks via DT
* Initialise timers via DT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'renesas-r8a7740-ccf-and-timers-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7740: Remove r8a7740_add_standard_devices_dt
ARM: shmobile: armadillo800eva-reference: Do not use r8a7740_add_standard_devices_dt()
ARM: shmobile: armadillo800eva-reference: Enable CMT1 in device tree
ARM: shmobile: r8a7740: Add CMT1 device to DT
ARM: shmobile: armadillo800eva-reference: add clock overrides to DTS
ARM: shmobile: r8a7740: add MSTP clock assignments to DT
ARM: shmobile: r8a7740: add SoC clocks to DTS
ARM: shmobile: r8a7740: clock register bits
Initial support for the r8a7794 SoC, based on work by Hisashi Nakamura.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now when the r8a7740 generic multiplatform case has the same
features as the DT reference board code then get rid of the
Armadillo800EVA DT reference C board code. DT Reference code
in the future shall make use of the r8a7740 Multiplatform
support code with the generic SoC machine vector.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Port the r8a7740 restart handling from the Armadillo code
to the r8a7740 generic multiplatform case.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable r8a7740 Multiplatform support for the generic r8a7740
machine vector. No board support is enabled, and the board
code for Armadillo 800 EVA DT Reference is left by itself.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As per recent revisions of the datasheet.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Consolidate SH_CLK_CPG under ARCH_SHMOBILE_LEGACY so it can
be shared by the legacy ARM mach-shmobile support code.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Consolidate CPU_V7 under ARCH_SHMOBILE_LEGACY so it can
be shared by the legacy ARM mach-shmobile support code.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adjust the ARM mach-shmobile Kconfig bits to only
select PM_RMOBILE in case of legacy. This allows us
to enable partial multiplatform support for various
SoCs before Power Domains DT bindings are finalized.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a CONFIG_PM_RMOBILE entry and enable it for R-Mobile
SoCs in case CONFIG_PM is set. Consolidate Makefile power
management objects and get rid of #ifdefs in the C code.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a CONFIG_PM_RCAR entry and enable it for R-Car
Generation 1 or 2 in case CONFIG_PM or CONFIG_SMP
is set. Consolidate power management objects and
get rid of #ifdefs in the C code.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a Kconfig entry for R-Car Generation 2 SoCs that
enables CMT timer and the IRQC interrupt driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a Kconfig entry for R-Car Generation 1 SoCs that
enables TMU timer and the INTC IRQPIN driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a Kconfig entry for R-Mobile SoCs that enables
both CMT and TMU timers. Interrupt controller varies
with SoC version so it is excluded.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
This resolves a problem introduced by 4bfb358b1d
("ARM: shmobile: Add r8a7791 legacy SDHI clocks")
which was included in v3.15.
This fix does not have any run-time affect at this time.
* ARM: shmobile: r8a7790: add missing 0x0100 for SDCKCR
This resolves a problem introduced by 9f13ee6f83
("ARM: shmobile: r8a7790: add div4 clocks")
which was included in v3.11.
This fix does not have any run-time affect at this time.
* ARM: shmobile: sh73a0: Remove spurious 0x from SCIFB clock name
This resolves a problem introduced by a0f7e7496d
("ARM: shmobile: sh73a0: add CMT1 clock support for DT")
which was included in v3.17-rc1.
This fix does not have any run-time affect at this time as the clock in
question is used by a SCIF device that is not enabled by default.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jurT
-----END PGP SIGNATURE-----
Merge tag 'renesas-clock-fixes-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Renesas ARM Based SoC Clock Fixes For v3.17" from Simon Horman:
* ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
This resolves a problem introduced by 4bfb358b1d
("ARM: shmobile: Add r8a7791 legacy SDHI clocks")
which was included in v3.15.
This fix does not have any run-time affect at this time.
* ARM: shmobile: r8a7790: add missing 0x0100 for SDCKCR
This resolves a problem introduced by 9f13ee6f83
("ARM: shmobile: r8a7790: add div4 clocks")
which was included in v3.11.
This fix does not have any run-time affect at this time.
* ARM: shmobile: sh73a0: Remove spurious 0x from SCIFB clock name
This resolves a problem introduced by a0f7e7496d
("ARM: shmobile: sh73a0: add CMT1 clock support for DT")
which was included in v3.17-rc1.
This fix does not have any run-time affect at this time as the clock in
question is used by a SCIF device that is not enabled by default.
* tag 'renesas-clock-fixes-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
ARM: shmobile: r8a7790: add missing 0x0100 for SDCKCR
ARM: shmobile: sh73a0: Remove spurious 0x from SCIFB clock name
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that r8a7740_add_standard_devices_dt() is simply a wrapper
for a call to of_platform_populate() remove it and call
of_platform_populate() directly.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that r8a7740_add_standard_devices_dt() is just a wrapper for
of_platform_populate() call the latter directly.
This is in preparation for removing r8a7740_add_standard_devices_dt().
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently the sh-intc driver is compiled on all SuperH and
non-multiplatform SH-Mobile platforms, while it's only used on a limited
number of platforms:
- SuperH: SH2(A), SH3(A), SH4(A)(L) (all but SH5)
- ARM: sh7372, sh73a0
Drop the "default y" on SH_INTC, make all CPU platforms that use it
select it, and protect all sub-options by "if SH_INTC" to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move all definitions for legacy INTC from the common "irqs.h" to the
INTC-specific "intc.h".
Include "intc.h" in sh7372/sh73a0 CPU and board files where needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
[horms+renesas@verge.net.au: omitted whitespace change]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The CPUFreq platform device is already registered by
shmobile_init_late(), so get rid of ape6evm specific bits.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The CPUFreq platform device is already registered by
shmobile_init_late(), so get rid of sh73a0 specific bits.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adjust the KZM9G board support code to use shmobile_init_delay()
together with CPU Frequency settings from the DTS.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adjust the BockW board support code to use shmobile_init_delay()
together with CPU Frequency settings from the DTS.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adjust the r8a7778 SoC support code to use shmobile_init_delay()
together with CPU Frequency settings from the DTS. Get rid of the
C code version.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adjust the sh73a0 SoC support code to use shmobile_init_delay()
together with CPU Frequency settings from the DTS. Get rid of the
C code version.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All ARM mach-shmobile SoCs and boards now rely on DTS for
CPU Frequency information, so remove the unused function
shmobile_setup_delay(). While at it, make the function
shmobile_setup_delay_hz() static.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adjust the r8a73a4 SoC support code to use shmobile_init_delay()
together with CPU Frequency settings from the DTS. Get rid of the
C code version and r8a73a4_init_early() that now are unused.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adjust the sh7372 SoC support code to use shmobile_init_delay()
together with CPU Frequency settings from the DTS. Get rid of the
C code version.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
4bfb358b1d
(ARM: shmobile: Add r8a7791 legacy SDHI clocks)
added r8a7791 SDHI clock support.
But, it is missing
"0x0100: x 1/8" division ratio.
This patch fixes hidden bug.
It is based on R-Car H2 v0.7, R-Car M2 v0.9.
Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
9f13ee6f83
(ARM: shmobile: r8a7790: add div4 clocks)
added r8a7790 DIV4 clock support.
But, it is missing
"0x0100: x 1/8" division ratio.
This patch fixes hidden bug.
It is based on R-Car H2 v0.7, R-Car M2 v0.9.
Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As per arch_probe_nr_irqs(), the default value is NR_IRQS, which maps to
NR_IRQS_LEGACY if CONFIG_SPARSE_IRQ=y.
Since SPARSE_IRQ is selected by both ARCH_MULTIPLATFORM and
ARCH_SHMOBILE_LEGACY, it's always enabled on shmobile.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As per arch_probe_nr_irqs(), the default value is NR_IRQS, which maps to
NR_IRQS_LEGACY if CONFIG_SPARSE_IRQ=y.
Since SPARSE_IRQ is selected by both ARCH_MULTIPLATFORM and
ARCH_SHMOBILE_LEGACY, it's always enabled on shmobile.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove NR_IRQS_LEGACY from the r8a7779 generic machine
vector. The generic r8a7779 machine vector requires use
of Multiplatform, and in such case SPARSE_IRQ is enabled
by default. This in turns means that the default value
of .nr_irqs equals NR_IRQS and NR_IRQS_LEGACY. Because
of this we can simply remove NR_IRQS_LEGACY and move one
step closer to a cruft-free environment.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now when the majority of the include files have moved from
arch/arm/mach-shmobile/include/mach/ to arch/arm/mach-shmobile/
remove the header include file workaround in the Makefile...
... and add another workaround in irqs.h to cope with the fact
that <mach/irqs.h> needs to be where it is until the PFC code
has been updated to remove legacy non-DT interfaces.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Extend r7s72100 SoC machine vector to include shmobile_init_late()
so Suspend-to-RAM and CPUIdle are setup as expected.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Extend r8a73a4 SoC machine vector to include shmobile_init_late()
so Suspend-to-RAM and CPUIdle are setup as expected.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fix r8a7778 SoC machine vector to include shmobile_init_late()
so Suspend-to-RAM and CPUIdle are setup and platform devices
are omitted as expected.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fix r8a7779 SoC machine vector to include shmobile_init_late()
so Suspend-to-RAM and CPUIdle are setup and platform devices
are omitted as expected.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Extend sh73a0 SoC machine vector to include shmobile_init_late()
so Suspend-to-RAM and CPUIdle are setup as expected.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As per arch_probe_nr_irqs(), the default value is NR_IRQS, which maps to
NR_IRQS_LEGACY if CONFIG_SPARSE_IRQ=y.
Since SPARSE_IRQ is selected by both ARCH_MULTIPLATFORM and
ARCH_SHMOBILE_LEGACY, it's always enabled on shmobile.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As per arch_probe_nr_irqs(), the default value is NR_IRQS, which maps to
NR_IRQS_LEGACY if CONFIG_SPARSE_IRQ=y.
Since SPARSE_IRQ is selected by both ARCH_MULTIPLATFORM and
ARCH_SHMOBILE_LEGACY, it's always enabled on shmobile.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove NR_IRQS_LEGACY from the Marzen Reference code.
The Marzen Reference machine vector requires use of
Multiplatform, and in such case SPARSE_IRQ is enabled
by default. This in turns means that the default value
of .nr_irqs equals NR_IRQS and NR_IRQS_LEGACY. Because
of this we can simply remove NR_IRQS_LEGACY and move one
step closer to a cruft-free environment.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a73a4 DTS includes CPU Frequency information so
adjust the APE6EVM board code to use shmobile_init_delay()
instead of relying on CPU Frequency information included
in r8a73a4_init_delay() that is specified in C.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Extend board specific APE6EVM reference machine vectors to include
shmobile_init_late() so Suspend-to-RAM and CPUIdle are setup as expected.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Extend board specific Bock-W DT reference machine vector to include
shmobile_init_late() so Suspend-to-RAM and CPUIdle are setup as expected.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Extend board specific Marzen DT reference machine vector to include
shmobile_init_late() so Suspend-to-RAM and CPUIdle are setup as expected.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Extend board specific KZM9D DT reference machine vector to include
shmobile_init_late() so Suspend-to-RAM and CPUIdle are setup as expected.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There's no legacy board anymore, genmai now boots with multiplatform
support only. Remove the leftovers.
Makefile.boot portion pointed out by Paul Bolle.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Wolfram Sang <wsa@sang-engineering.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
[horms+renesas@verge.net.au: squashed in patch containing
Makefile.boot change]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The genmai board now boots using DT and multiplatform kernel with the
same feature set as the legacy board. Remove the legacy board file and
the board Kconfig option.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The genmai board now boots using the generic R7S72100 DT machine with
the same feature set as the board file. Remove the board file.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the missing call to shmobile_init_late() to r8a7778_init_late().
This should make sure Suspend-to-RAM and CPUIdle are setup as expected
on bockw.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No more device needs to be added from platform code when booting the
reference platform, move MTU2 registration from setup-r7s72100.c to
board-genmai.c and remove the now empty r7s72100_add_dt_devices()
function.
As the genmai_add_standard_devices() function is now identical to the
default init_machine implementation, remove it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No more device needs to be added from platform code when booting the
reference platform, remove the now empty
r8a7779_add_standard_devices_dt() function completely.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No more device needs to be added from platform code when booting the
reference platform, remove the now empty r8a7791_add_dt_devices()
function completely.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No more device needs to be added from platform code when booting the
reference platform, remove the now empty r8a7790_add_dt_devices()
function completely.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new platforms,
but there's also a bit of cleanup and code removal for things that
are moved from platform code to DT contents (some OMAP clock code in
particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no particular
order:
* Rockchip RK3288 SoC support, including DTS for a dev board that they
have seeded with some community developers.
* Better support for Hardkernel Exynos4-based ODROID boards.
* CCF conversions (and dtsi contents) for several Renesas platforms.
* Gumstix Pepper (TI AM335x) board support
* TI eval board support for AM437x
* Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an Ippo
tablet with the chipset.
* Allwinner A31 Hummingbird board support, not to be confused with the
SolidRun i.MX-based Hummingboard.
* Tegra30 Apalis board support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJT5DqvAAoJEIwa5zzehBx3tm0QAJk8zFyZuMhUPz6SoZTtO9ti
zojZ2218oqLRDfLSYdJx/3QE7gb2ef0e2S6FrthecdAY8sqZzDddL7M/cCf1WSgy
+D4dD1UEq+W/hOeEwIWyo3GR/71exgo/LMTIw8HOJh5c9fanQ2wNChNetCgh8b4u
sVOEMmP1UTO2W7mH9cCRhWXFifBNi0yNl1QBYnLPzM2CbSEa4qQRarTn/94NSEiY
U9XgzysklvYEW/30wcEkz8ZonKbJrtP+zEjODU4wN/muhHECeTehDrkJq0WEK/3C
3ptko2xQGURNaLM6HVvQS9qkXxyhCeZxqkELpjkjjM+YPFN8wdHu7gDctGZlDr39
LQ2pZF6K8vaFvxp3UM2wzdDeoNi3rxguzpFoBmfRP5NWguDrOvjT3w8W4hO9q04J
8SqMGca0av9myHmeSjtRRg5rmcC3kBbOgSN6siVJ8W80rHT7tnFjl6eCawDreQzn
szFzGaOOUnf/kJ/00vzm1dCuluowFPdSYgW3aamZhfkqu2qYJ8Ztuooz5eZGKtex
zlUfKtpL26gnamoUT42K7E8J968AjHjUc/zimwYzIgHCzTTApYGJQcbD/Y28b8QH
gTvhRxP+0kFb+NNq4IHStVMvJrFOPvzOHXcL8x07HqTxrl7W4XoW+KJxCJOk433W
5NJ9s4tEmiTRMtFL1kv6
=xxlY
-----END PGP SIGNATURE-----
Merge tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device-tree changes from Olof Johansson:
"Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new
platforms, but there's also a bit of cleanup and code removal for
things that are moved from platform code to DT contents (some OMAP
clock code in particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no
particular order:
- Rockchip RK3288 SoC support, including DTS for a dev board that
they have seeded with some community developers.
- Better support for Hardkernel Exynos4-based ODROID boards.
- CCF conversions (and dtsi contents) for several Renesas platforms.
- Gumstix Pepper (TI AM335x) board support
- TI eval board support for AM437x
- Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an
Ippo tablet with the chipset.
- Allwinner A31 Hummingbird board support, not to be confused with
the SolidRun i.MX-based Hummingboard.
- Tegra30 Apalis board support"
* tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (334 commits)
ARM: dts: Enable USB host0 (EHCI) on rk3288-evb
ARM: dts: add rk3288 ehci usb devices
ARM: dts: Turn on USB host vbus on rk3288-evb
ARM: tegra: apalis t30: fix device tree compatible node
ARM: tegra: paz00: Fix some indentation inconsistencies
ARM: zynq: DT: Clarify Xilinx Zynq platform
ARM: dts: rockchip: add watchdog node
ARM: dts: rockchip: remove pinctrl setting from radxarock uart2
ARM: dts: Add missing pinctrl for uart0/1 for exynos3250
ARM: dts: Remove duplicate 'interrput-parent' property for exynos3250
ARM: dts: Add TMU dt node to monitor the temperature for exynos3250
ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250
ARM: dts: cypress,cyapa trackpad is exynos5250-Snow only
ARM: dts: max77686 is exynos5250-snow only
ARM: zynq: DT: Remove DMA from board DTs
ARM: zynq: DT: Add CAN node
ARM: EXYNOS: Add exynos5260 PMU compatible string to DT match table
ARM: dts: Add PMU DT node for exynos5260 SoC
ARM: EXYNOS: Add support for Exynos5410 PMU
ARM: dts: Add PMU to exynos5410
...
This is the smallest board branch we have ever had. Most of this is a
few cleanups for board code for Renesas shmobile, with a bit of legacy
driver support added. This is strongly trending in the right direction now.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=m3yA
-----END PGP SIGNATURE-----
Merge tag 'boards-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board changes from Olof Johansson:
"This is the smallest board branch we have ever had. Most of this is a
few cleanups for board code for Renesas shmobile, with a bit of legacy
driver support added. This is strongly trending in the right
direction now"
* tag 'boards-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: shmobile: Enable R-Car Gen2 CMA code in board files
ARM: shmobile: armadillo800eva reference: Spelling s/ED/LED/
ARM: shmobile: armadillo800eva legacy: Add LED support
ARM: shmobile: lager-reference: Remove workarounds for core clock issues
ARM: shmobile: koelsch-reference: Remove workarounds for core clock issues
This is the bulk of new SoC enablement and other platform changes for 3.17:
* Samsung S5PV210 has been converted to DT and multiplatform
* Clock drivers and bindings for some of the lower-end i.MX 1/2 platforms
* Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood.
* Hwmod data for TI AM43xx and DRA7 platforms.
* More additions of Renesas shmobile platform support
* Removal of plat-samsung contents that can be removed with S5PV210 being
multiplatform/DT-enabled and the other two old platforms being removed.
New platforms (most with only basic support right now):
* Hisilicon X5HD2 settop box chipset is introduced
* Mediatek MT6589 (mobile chipset) is introduced
* Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=5TJ6
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This is the bulk of new SoC enablement and other platform changes for
3.17:
- Samsung S5PV210 has been converted to DT and multiplatform
- Clock drivers and bindings for some of the lower-end i.MX 1/2
platforms
- Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood
- Hwmod data for TI AM43xx and DRA7 platforms
- More additions of Renesas shmobile platform support
- Removal of plat-samsung contents that can be removed with S5PV210
being multiplatform/DT-enabled and the other two old platforms
being removed
New platforms (most with only basic support right now):
- Hisilicon X5HD2 settop box chipset is introduced
- Mediatek MT6589 (mobile chipset) is introduced
- Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code"
* tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits)
ARM: hisi: remove smp from machine descriptor
power: reset: move hisilicon reboot code
ARM: dts: Add hix5hd2-dkb dts file.
ARM: debug: Rename Hi3716 to HIX5HD2
ARM: hisi: enable hix5hd2 SoC
ARM: hisi: add ARCH_HISI
MAINTAINERS: add entry for Broadcom ARM STB architecture
ARM: brcmstb: select GISB arbiter and interrupt drivers
ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
ARM: configs: enable SMP in bcm_defconfig
ARM: add SMP support for Broadcom mobile SoCs
Documentation: arm: misc updates to Marvell EBU SoC status
Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC
ARM: mvebu: fix build without platforms selected
ARM: mvebu: add cpuidle support for Armada 38x
ARM: mvebu: add cpuidle support for Armada 370
cpuidle: mvebu: add Armada 38x support
cpuidle: mvebu: add Armada 370 support
cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7
ARM: mvebu: export the SCU address
...
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
- ACPICA update to upstream version 20140724. That includes
ACPI 5.1 material (support for the _CCA and _DSD predefined names,
changes related to the DMAR and PCCT tables and ARM support among
other things) and cleanups related to using ACPICA's header files.
A major part of it is related to acpidump and the core code used
by that utility. Changes from Bob Moore, David E Box, Lv Zheng,
Sascha Wildner, Tomasz Nowicki, Hanjun Guo.
- Radix trees for memory bitmaps used by the hibernation core from
Joerg Roedel.
- Support for waking up the system from suspend-to-idle (also known
as the "freeze" sleep state) using ACPI-based PCI wakeup signaling
(Rafael J Wysocki).
- Fixes for issues related to ACPI button events (Rafael J Wysocki).
- New device ID for an ACPI-enumerated device included into the
Wildcat Point PCH from Jie Yang.
- ACPI video updates related to backlight handling from Hans de Goede
and Linus Torvalds.
- Preliminary changes needed to support ACPI on ARM from Hanjun Guo
and Graeme Gregory.
- ACPI PNP core cleanups from Arjun Sreedharan and Zhang Rui.
- Cleanups related to ACPI_COMPANION() and ACPI_HANDLE() macros
(Rafael J Wysocki).
- ACPI-based device hotplug cleanups from Wei Yongjun and
Rafael J Wysocki.
- Cleanups and improvements related to system suspend from
Lan Tianyu, Randy Dunlap and Rafael J Wysocki.
- ACPI battery cleanup from Wei Yongjun.
- cpufreq core fixes from Viresh Kumar.
- Elimination of a deadband effect from the cpufreq ondemand
governor and intel_pstate driver cleanups from Stratos Karafotis.
- 350MHz CPU support for the powernow-k6 cpufreq driver from
Mikulas Patocka.
- Fix for the imx6 cpufreq driver from Anson Huang.
- cpuidle core and governor cleanups from Daniel Lezcano,
Sandeep Tripathy and Mohammad Merajul Islam Molla.
- Build fix for the big_little cpuidle driver from Sachin Kamat.
- Configuration fix for the Operation Performance Points (OPP)
framework from Mark Brown.
- APM cleanup from Jean Delvare.
- cpupower utility fixes and cleanups from Peter Senna Tschudin,
Andrey Utkin, Himangi Saraogi, Rickard Strandqvist, Thomas Renninger.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ZODv
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"Again, ACPICA leads the pack (47 commits), followed by cpufreq (18
commits) and system suspend/hibernation (9 commits).
From the new code perspective, the ACPICA update brings ACPI 5.1 to
the table, including a new device configuration object called _DSD
(Device Specific Data) that will hopefully help us to operate device
properties like Device Trees do (at least to some extent) and changes
related to supporting ACPI on ARM.
Apart from that we have hibernation changes making it use radix trees
to store memory bitmaps which should speed up some operations carried
out by it quite significantly. We also have some power management
changes related to suspend-to-idle (the "freeze" sleep state) support
and more preliminary changes needed to support ACPI on ARM (outside of
ACPICA).
The rest is fixes and cleanups pretty much everywhere.
Specifics:
- ACPICA update to upstream version 20140724. That includes ACPI 5.1
material (support for the _CCA and _DSD predefined names, changes
related to the DMAR and PCCT tables and ARM support among other
things) and cleanups related to using ACPICA's header files. A
major part of it is related to acpidump and the core code used by
that utility. Changes from Bob Moore, David E Box, Lv Zheng,
Sascha Wildner, Tomasz Nowicki, Hanjun Guo.
- Radix trees for memory bitmaps used by the hibernation core from
Joerg Roedel.
- Support for waking up the system from suspend-to-idle (also known
as the "freeze" sleep state) using ACPI-based PCI wakeup signaling
(Rafael J Wysocki).
- Fixes for issues related to ACPI button events (Rafael J Wysocki).
- New device ID for an ACPI-enumerated device included into the
Wildcat Point PCH from Jie Yang.
- ACPI video updates related to backlight handling from Hans de Goede
and Linus Torvalds.
- Preliminary changes needed to support ACPI on ARM from Hanjun Guo
and Graeme Gregory.
- ACPI PNP core cleanups from Arjun Sreedharan and Zhang Rui.
- Cleanups related to ACPI_COMPANION() and ACPI_HANDLE() macros
(Rafael J Wysocki).
- ACPI-based device hotplug cleanups from Wei Yongjun and Rafael J
Wysocki.
- Cleanups and improvements related to system suspend from Lan
Tianyu, Randy Dunlap and Rafael J Wysocki.
- ACPI battery cleanup from Wei Yongjun.
- cpufreq core fixes from Viresh Kumar.
- Elimination of a deadband effect from the cpufreq ondemand governor
and intel_pstate driver cleanups from Stratos Karafotis.
- 350MHz CPU support for the powernow-k6 cpufreq driver from Mikulas
Patocka.
- Fix for the imx6 cpufreq driver from Anson Huang.
- cpuidle core and governor cleanups from Daniel Lezcano, Sandeep
Tripathy and Mohammad Merajul Islam Molla.
- Build fix for the big_little cpuidle driver from Sachin Kamat.
- Configuration fix for the Operation Performance Points (OPP)
framework from Mark Brown.
- APM cleanup from Jean Delvare.
- cpupower utility fixes and cleanups from Peter Senna Tschudin,
Andrey Utkin, Himangi Saraogi, Rickard Strandqvist, Thomas
Renninger"
* tag 'pm+acpi-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (118 commits)
ACPI / LPSS: add LPSS device for Wildcat Point PCH
ACPI / PNP: Replace faulty is_hex_digit() by isxdigit()
ACPICA: Update version to 20140724.
ACPICA: ACPI 5.1: Update for PCCT table changes.
ACPICA/ARM: ACPI 5.1: Update for GTDT table changes.
ACPICA/ARM: ACPI 5.1: Update for MADT changes.
ACPICA/ARM: ACPI 5.1: Update for FADT changes.
ACPICA: ACPI 5.1: Support for the _CCA predifined name.
ACPICA: ACPI 5.1: New notify value for System Affinity Update.
ACPICA: ACPI 5.1: Support for the _DSD predefined name.
ACPICA: Debug object: Add current value of Timer() to debug line prefix.
ACPICA: acpihelp: Add UUID support, restructure some existing files.
ACPICA: Utilities: Fix local printf issue.
ACPICA: Tables: Update for DMAR table changes.
ACPICA: Remove some extraneous printf arguments.
ACPICA: Update for comments/formatting. No functional changes.
ACPICA: Disassembler: Add support for the ToUUID opererator (macro).
ACPICA: Remove a redundant cast to acpi_size for ACPI_OFFSET() macro.
ACPICA: Work around an ancient GCC bug.
ACPI / processor: Make it possible to get local x2apic id via _MAT
...
There've been many updates in ASoC side at this time, especially the
framework enhancement for multiple CODECs on a single DAI and more
componentization works. The only major change in ALSA core is the
addition of timestamp type in sw_params field. This should behave in
backward compatible way. Other than that, there are lots of small
changes and new drivers in wide range, including a large code cut in
HD-audio driver for deprecated static quirks. Some highlights are
below:
ALSA Core:
- Add the new timestamp type field to sw_params to choose
MONOTONIC_RAW type
HD-audio:
- Continued conversion to standard printk macros, generic code
cleanups
- Removal of obsoleted static quirk codes for Conexant and C-Media
codecs
- Fixups for HP Envy TS, Dell XPS 15, HP and Dell mute/mic LED,
Gigabyte BXBT-2807 mobo
- Intel Braswell support
ASoC:
- Support for multiple CODECs attached to a single DAI, enabling
systems with for example multiple DAC/speaker drivers on a single
link, contributed by Benoit Cousson based on work from Misael Lopez
Cruz
- Support for byte controls larger than 256 bytes based on the use of
TLVs contributed by Omair Mohammed Abdullah
- More componentisation work from Lars-Peter Clausen
- The remainder of the conversions of CODEC drivers to params_width()
by Mark Brown
- Drivers for Cirrus Logic CS4265, Freescale i.MX ASRC blocks, Realtek
RT286 and RT5670, Rockchip RK3xxx I2S controllers and Texas
Instruments TAS2552
- Lots of updates and fixes, especially to the DaVinci, Intel,
Freescale, Realtek, and rcar drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=RL72
-----END PGP SIGNATURE-----
Merge tag 'sound-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There've been many updates in ASoC side at this time, especially the
framework enhancement for multiple CODECs on a single DAI and more
componentization works.
The only major change in ALSA core is the addition of timestamp type
in sw_params field. This should behave in backward compatible way.
Other than that, there are lots of small changes and new drivers in
wide range, including a large code cut in HD-audio driver for
deprecated static quirks. Some highlights are below:
ALSA Core:
- Add the new timestamp type field to sw_params to choose
MONOTONIC_RAW type
HD-audio:
- Continued conversion to standard printk macros, generic code
cleanups
- Removal of obsoleted static quirk codes for Conexant and C-Media
codecs
- Fixups for HP Envy TS, Dell XPS 15, HP and Dell mute/mic LED,
Gigabyte BXBT-2807 mobo
- Intel Braswell support
ASoC:
- Support for multiple CODECs attached to a single DAI, enabling
systems with for example multiple DAC/speaker drivers on a single
link, contributed by Benoit Cousson based on work from Misael Lopez
Cruz
- Support for byte controls larger than 256 bytes based on the use of
TLVs contributed by Omair Mohammed Abdullah
- More componentisation work from Lars-Peter Clausen
- The remainder of the conversions of CODEC drivers to params_width()
by Mark Brown
- Drivers for Cirrus Logic CS4265, Freescale i.MX ASRC blocks,
Realtek RT286 and RT5670, Rockchip RK3xxx I2S controllers and Texas
Instruments TAS2552
- Lots of updates and fixes, especially to the DaVinci, Intel,
Freescale, Realtek, and rcar drivers"
* tag 'sound-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (402 commits)
ALSA: usb-audio: Whitespace cleanups for sound/usb/midi.*
ALSA: usb-audio: Respond to suspend and resume callbacks for MIDI input
sound/oss/pss: Remove typedefs pss_mixerdata and pss_confdata
sound/oss/opl3: Remove typedef opl_devinfo
ALSA: fireworks: fix specifiers in format strings for propper output
ASoC: imx-audmux: Use uintptr_t for port numbers
ASoC: davinci: Enable menuconfig entry for McASP
ASoC: fsl_asrc: Don't access members of config before checking it
ASoC: fsl_sarc_dma: Check pair before using it
ASoC: adau1977: Fix truncation warning on 64 bit architectures
ALSA: virtuoso: add Xonar Essence STX II support
ALSA: riptide: fix %d confusingly prefixed with 0x in format strings
ALSA: fireworks: fix %d confusingly prefixed with 0x in format strings
ALSA: hda - add codec ID for Braswell display audio codec
ALSA: hda - add PCI IDs for Intel Braswell
ALSA: usb-audio: Adjust Gamecom 780 volume level
ALSA: usb-audio: improve dmesg source grepability
ASoC: rt5670: Fix duplicate const warnings
ASoC: rt5670: Staticise non-exported symbols
ASoC: Intel: update stream only on stream IPC msgs
...
Pull ARM updates from Russell King:
"Included in this update:
- perf updates from Will Deacon:
The main changes are callchain stability fixes from Jean Pihet and
event mapping and PMU name rework from Mark Rutland
The latter is preparatory work for enabling some code re-use with
arm64 in the future.
- updates for nommu from Uwe Kleine-König:
Two different fixes for the same problem making some ARM nommu
configurations not boot since 3.6-rc1. The problem is that
user_addr_max returned the biggest available RAM address which
makes some copy_from_user variants fail to read from XIP memory.
- deprecate legacy OMAP DMA API, in preparation for it's removal.
The popular drivers have been converted over, leaving a very small
number of rarely used drivers, which hopefully can be converted
during the next cycle with a bit more visibility (and hopefully
people popping out of the woodwork to help test)
- more tweaks for BE systems, particularly with the kernel image
format. In connection with this, I've cleaned up the way we
generate the linker script for the decompressor.
- removal of hard-coded assumptions of the kernel stack size, making
everywhere depend on the value of THREAD_SIZE_ORDER.
- MCPM updates from Nicolas Pitre.
- Make it easier for proper CPU part number checks (which should
always include the vendor field).
- Assembly code optimisation - use the "bx" instruction when
returning from a function on ARMv6+ rather than "mov pc, reg".
- Save the last kernel misaligned fault location and report it via
the procfs alignment file.
- Clean up the way we create the initial stack frame, which is a
repeated pattern in several different locations.
- Support for 8-byte get_user(), needed for some DRM implementations.
- mcs locking from Will Deacon.
- Save and restore a few more Cortex-A9 registers (for errata
workarounds)
- Fix various aspects of the SWP emulation, and the ELF hwcap for the
SWP instruction.
- Update LPAE logic for pte_write and pmd_write to make it more
correct.
- Support for Broadcom Brahma15 CPU cores.
- ARM assembly crypto updates from Ard Biesheuvel"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (53 commits)
ARM: add comments to the early page table remap code
ARM: 8122/1: smp_scu: enable SCU standby support
ARM: 8121/1: smp_scu: use macro for SCU enable bit
ARM: 8120/1: crypto: sha512: add ARM NEON implementation
ARM: 8119/1: crypto: sha1: add ARM NEON implementation
ARM: 8118/1: crypto: sha1/make use of common SHA-1 structures
ARM: 8113/1: remove remaining definitions of PLAT_PHYS_OFFSET from <mach/memory.h>
ARM: 8111/1: Enable erratum 798181 for Broadcom Brahma-B15
ARM: 8110/1: do CPU-specific init for Broadcom Brahma15 cores
ARM: 8109/1: mm: Modify pte_write and pmd_write logic for LPAE
ARM: 8108/1: mm: Introduce {pte,pmd}_isset and {pte,pmd}_isclear
ARM: hwcap: disable HWCAP_SWP if the CPU advertises it has exclusives
ARM: SWP emulation: only initialise on ARMv7 CPUs
ARM: SWP emulation: always enable when SMP is enabled
ARM: 8103/1: save/restore Cortex-A9 CP15 registers on suspend/resume
ARM: 8098/1: mcs lock: implement wfe-based polling for MCS locking
ARM: 8091/2: add get_user() support for 8 byte types
ARM: 8097/1: unistd.h: relocate comments back to place
ARM: 8096/1: Describe required sort order for textofs-y (TEXT_OFFSET)
ARM: 8090/1: add revision info for PL310 errata 588369 and 727915
...
* Add legacy clocks for SCI for SoCs that do not yet have CCF support.
This is to allow timer devices to be enabled using DT and
will be removed after CCF support is added for each SoC.
This is in keeping with the approach taken for enabling
SCI (serial) devices using DT on these SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8vte
-----END PGP SIGNATURE-----
Merge tag 'renesas-clock3-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Third Round of Renesas ARM Based SoC Clock Updates for v3.17" from Simon
Horman:
Third Round of Renesas ARM Based SoC Clock Updates for v3.17
* Add legacy clocks for SCI for SoCs that do not yet have CCF support.
This is to allow timer devices to be enabled using DT and
will be removed after CCF support is added for each SoC.
This is in keeping with the approach taken for enabling
SCI (serial) devices using DT on these SoCs.
* tag 'renesas-clock3-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: sh73a0: add CMT1 clock support for DT
ARM: shmobile: r8a7740: add CMT1 clock support for DT
ARM: shmobile: r8a73a4: add CMT1 clock support for DT
ARM: shmobile: r8a7740: add TMU clock support for DT
ARM: shmobile: r8a7778: add TMU clock support for DT
Signed-off-by: Olof Johansson <olof@lixom.net>
A number of board files in arch/arm and arch/unicore32
explicitly reference platform_bus device as a parent
for new platform devices.
This is unnecessary, as platform device API guarantees
that devices with NULL parent are going to by adopted
by the mentioned "root" device.
This patch removes or replaces with NULL such references.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the OPP layer is a kernel library which has been converted to be
directly selectable by its callers rather than user selectable and
requiring architectures to enable it explicitly the ARCH_HAS_OPP symbol
has become redundant and can be removed. Do so.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* Add legacy clocks for SCI for SoCs that do not yet have CCF support.
This is to allow SCI (serial) devices to be enabled using DT and
will be removed after CCF support is added for each SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTxKxCAAoJENfPZGlqN0++Bt4QAIr9N0wh2V77cQSMegTDlRRg
sawwaTStkG8mbuRdUrYGS/kWJg1UvKvvB4pNG5IHm5vjycg5f4ya8a9fK5rXwXGx
lW1G8xKxb9LSgOtZaMLXzZPI1v6C1GOVzDmouhZ19WvlFtRI7OJKrX7dvvWnU3+R
8XxsU/XRX8o0NWa/vZg/524+pwyffZihREY30LUcJwsFbFpChwki6KETl/RuTB8J
SqlpbXv964D9CZ9fF4UkTkN64wGODxPYTsUTfOl7QlMIkHb9ajA/OordGg5zZWvJ
phk0tgfr0Y/Lar9LzKheR9qLPRdD1oqVsQ+7COpleIiF+Iey8ICsV13CXgsp9qA9
FqFyUd7xneZ0Jeigw4vgCT474I84E9Q/cXLnN/ExBgStAGhf/IDB7U+CvKaDd6qB
+UVKFRjGJgDjzXy05WYtckrH2xHMS4HYdkg+XxKgxXmTl/0NEFRvZa9B1aE3A0FK
adzdxLckOzebgIIpN1IL7V8851h+Yo0YnigMmrf0zlv2QVwn9bjQ3XSfxVCTEhjJ
Qp1ECqGJIluKQ2HC5KDjsxShdTZGicIQlOn2DW6gZPF1zWqTv/A7cD4tP+lwhLhg
ThKALzIj4jPWIKCO0C9Fe73LXZXoQ8NShIGBKhGaIxVYJgz6B8KYv9dkHD+Q262X
mdUAYDVpoKPfpFd8jRyE
=HQjb
-----END PGP SIGNATURE-----
Merge tag 'renesas-clock2-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Second Round of Renesas ARM Based SoC Clock Updates for v3.17" from
Simon Horman:
- Add legacy clocks for SCI for SoCs that do not yet have CCF support.
This is to allow SCI (serial) devices to be enabled using DT and
will be removed after CCF support is added for each SoC.
* tag 'renesas-clock2-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: sh73a0: add SCI clock support for DT
ARM: shmobile: r8a7740: correct SCI clock support for DT
ARM: shmobile: r8a73a4: add SCI clock support for DT
ARM: shmobile: r8a7778: add SCI clock support for DT
Signed-off-by: Olof Johansson <olof@lixom.net>
ARMv6 and greater introduced a new instruction ("bx") which can be used
to return from function calls. Recent CPUs perform better when the
"bx lr" instruction is used rather than the "mov pc, lr" instruction,
and this sequence is strongly recommended to be used by the ARM
architecture manual (section A.4.1.1).
We provide a new macro "ret" with all its variants for the condition
code which will resolve to the appropriate instruction.
Rather than doing this piecemeal, and miss some instances, change all
the "mov pc" instances to use the new macro, with the exception of
the "movs" instruction and the kprobes code. This allows us to detect
the "mov pc, lr" case and fix it up - and also gives us the possibility
of deploying this for other registers depending on the CPU selection.
Reported-by: Will Deacon <will.deacon@arm.com>
Tested-by: Stephen Warren <swarren@nvidia.com> # Tegra Jetson TK1
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> # mioa701_bootresume.S
Tested-by: Andrew Lunn <andrew@lunn.ch> # Kirkwood
Tested-by: Shawn Guo <shawn.guo@freescale.com>
Tested-by: Tony Lindgren <tony@atomide.com> # OMAPs
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com> # Armada XP, 375, 385
Acked-by: Sekhar Nori <nsekhar@ti.com> # DaVinci
Acked-by: Christoffer Dall <christoffer.dall@linaro.org> # kvm/hyp
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com> # PXA3xx
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> # Xen
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> # ARMv7M
Tested-by: Simon Horman <horms+renesas@verge.net.au> # Shmobile
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A stray '0x' crept into a0f7e7496d ("ARM: shmobile: sh73a0: add CMT1
clock support for DT"). This patch removes it.
This change should not have any run-time affect at this time as
the clock in question is used by a SCIF device that is not enabled by
default.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This will be used when initialising CMT1 device using DT
until common clock framework support is added.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This will be used when initialising CMT1 device using DT
until common clock framework support is added.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This will be used when initialising CMT1 device using DT
until common clock framework support is added.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This will be used when initialising TMU devices using DT
until common clock framework support is added.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This will be used when initialising TMU devices using DT
until common clock framework support is added.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Remove opps table check for cpufreq as this is already handled
by the driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sB8x
-----END PGP SIGNATURE-----
Merge tag 'renesas-cpufreq2-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Second Round of Renesas ARM Based SoC CPUFreq Updates for v3.17" from
Simon Horman:
- Remove opps table check for cpufreq as this is already handled
by the driver
* tag 'renesas-cpufreq2-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove opps table check for cpufreq
Signed-off-by: Olof Johansson <olof@lixom.net>
* Correct build failure in APMU code in the case of !SUSPEND
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/k+c
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc3-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Third Round of Renesas ARM Based SoC Updates for v3.17" from Simon
Horman:
- Correct build failure in APMU code in the case of !SUSPEND
* tag 'renesas-soc3-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: fix shmobile_smp_apmu_suspend_init build failure for !SUSPEND
Signed-off-by: Olof Johansson <olof@lixom.net>
* Suspend on non-SMP update for r8a7790
* Move r8a7791.h out of mach directory.
This is part of a multi-stage effort to move headers
out of that directory.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mQ5+
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc2-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Second Round of Renesas ARM Based SoC Updates for v3.17" from Simon
Horman:
* Suspend on non-SMP update for r8a7790
* Move r8a7791.h out of mach directory.
This is part of a multi-stage effort to move headers
out of that directory.
* tag 'renesas-soc2-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Allow r8a7791 to build non-SMP APMU code
ARM: shmobile: Move r8a7791 reset code to pm-r8a7791.c
ARM: shmobile: Allow r8a7790 to build non-SMP APMU code
ARM: shmobile: Move r8a7790 reset code to pm-r8a7790.c
ARM: shmobile: Use __init for APMU suspend init function
ARM: shmobile: Adjust APMU code to build for non-SMP
ARM: shmobile: Allow use of boot code for non-SMP case
ARM: shmobile: Move r8a7791.h
Signed-off-by: Olof Johansson <olof@lixom.net>
* Move SOC-specific headers out of mach directory.
This is part of a multi-stage effort to move headers
out of that directory.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ooGC
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-cleanup2-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
Merge "Second Round of Renesas ARM Based SoC soc-cleanup Updates for v3.17"
from Simon Horman:
* Move SOC-specific headers out of mach directory.
This is part of a multi-stage effort to move headers
out of that directory.
* tag 'renesas-soc-cleanup2-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Move sh7372.h
ARM: shmobile: Move sh73a0.h
ARM: shmobile: Move r8a7790.h
ARM: shmobile: Move r8a7778.h
ARM: shmobile: Move r8a7740.h
ARM: shmobile: Move r8a73a4.h
ARM: shmobile: Move r7s72100.h
Signed-off-by: Olof Johansson <olof@lixom.net>
* Move r8a7779.h out of mach directory.
This is part of a multi-stage effort to move headers
out of that directory.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTsfwOAAoJENfPZGlqN0++uAAP/0VefX1OFTFFfSbBF0srIMGp
LbwxFjxfip8MSQnwL8R93C51jP9OWO1ePKM5EE3uMDicEszlmr5otXTC5m8/c8Mn
BLK8hf0DCF2VH2lnNegH8QuLoNh3p3N7Ck8/PgIh/S0uUiOF0QdOKUEeFaCNqeg5
CTwUVv3xK8kteXcMxgUpB6F1dZA/Kw2KtlMIO4pH07M2bKif8W5wgCbr3GIHiGYP
DawE4s0kxCb0bTM6f+T0Q+KezstgTglYq4zjK4WezH+xAXGfmPRDQnXw/CHCRqdB
Ku87pqa9GSB68aqdk7kLSDk9WRaaPIeeRtsTkejmoXLtO2KesDBlWXV9fU88ueSt
zx/2VUTr2w75N6CvQidtvjU7vO3knokxC+CTKfUWXmw1ge90tMjB97q5NYlx+vxk
yLN5yQbzCED5kK8GUNZ3JptEUqD2rlD9pYz5BqXWh4JmCxNPsPK/4zU9IPZsM1Ga
zmK6hyCBogWPsy0WtdDhSrRSeWaCuE7XPU2tai3TdLl00W9sSgGUBsy86Am2vYq9
bENBVPw7qKOO83A0BnFkwZGQo8cR8FvAlkw1fP1wPgAUGOyivaEzEdbbL1GOl8eV
ucREW8dTkI00dQvByjl0w+6t3mP2cjJbJqNH2jSbeM2PlP+0oGm/olZ89zfFkJO8
snXaY03X+0nY4rtIy2MT
=RNdD
-----END PGP SIGNATURE-----
Merge tag 'renesas-r8a7779-multiplatform2-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Second Round of Renesas ARM Based SoC r8a7779-multiplatform
Updates for v3.17" from Simon Horman:
- Move r8a7779.h out of mach directory.
This is part of a multi-stage effort to move headers
out of that directory.
* tag 'renesas-r8a7779-multiplatform2-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Move r8a7779.h
Signed-off-by: Olof Johansson <olof@lixom.net>
Initialise SCIF device using DT when booting bockw
using DT reference.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This will be used when initialising SCI devices using DT
until common clock framework support is added.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When initialising SCI devices their names will be .serial
not .sci.
This will be used when initialising SCI devices using DT
until common clock framework support is added.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This will be used when initialising SCI devices using DT
until common clock framework support is added.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This will be used when initialising SCI devices using DT
until common clock framework support is added.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch is based on feedback from Viresh Kumar.
Since cpufreq-cpu0 driver has already check opp table, there is no
need to same check in mach-shmobile.
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* armadillo800eva LED support
* Remove now unnecessary work arounds for c\lock issues
* Enable R-Car Gen2 CMA code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/jQc
-----END PGP SIGNATURE-----
Merge tag 'renesas-boards-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards
Merge "Renesas ARM Based SoC Boards Updates for v3.17" from Simon Horman:
- armadillo800eva LED support
- Remove now unnecessary work arounds for c\lock issues
- Enable R-Car Gen2 CMA code
* tag 'renesas-boards-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Enable R-Car Gen2 CMA code in board files
ARM: shmobile: armadillo800eva reference: Spelling s/ED/LED/
ARM: shmobile: armadillo800eva legacy: Add LED support
ARM: shmobile: lager-reference: Remove workarounds for core clock issues
ARM: shmobile: koelsch-reference: Remove workarounds for core clock issues
Signed-off-by: Olof Johansson <olof@lixom.net>
* Use shmobile_init_late on r8a7791 and r8a7790 whien booting using DT-only
* Support Core-Standby for Suspend to RAM on r8a7791 and r8a7790 SoCs
* Shared CMA reservation for R-Car Gen2 SoCs
* Add r8a7791 SYSC power management support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6J6K
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Renesas ARM Based SoC Updates for v3.17" from Simon Horman:
- Use shmobile_init_late on r8a7791 and r8a7790 whien booting using DT-only
- Support Core-Standby for Suspend to RAM on r8a7791 and r8a7790 SoCs
- Shared CMA reservation for R-Car Gen2 SoCs
- Add r8a7791 SYSC power management support
* tag 'renesas-soc-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove ARCH_HAS_CPUFREQ config for shmobile
ARM: shmobile: rcar-gen2: update call to dma_contiguous_reserve_area
ARM: shmobile: rcar-gen2: correct return value of shmobile_smp_apmu_suspend_init
ARM: shmobile: rcar-gen2: Remove useless copied section for LongTrail
ARM: shmobile: rcar-gen2: Use "1ULL" instead of "(u64)1"
ARM: shmobile: rcar-gen2: Update for of_get_flat_dt_prop() update
ARM: shmobile: Add shared R-Car Gen2 CMA reservation code
ARM: shmobile: Use shmobile_init_late() on r8a7791 DT-only
ARM: shmobile: Use shmobile_init_late() on r8a7790 DT-only
ARM: shmobile: Mark all SoCs in shmobile as CPUFreq, capable
ARM: shmobile: r8a7791: Support Core-Standby for Suspend to RAM
ARM: shmobile: r8a7790: Support Core-Standby for Suspend to RAM
ARM: shmobile: APMU: Add Core-Standby-state for Suspend to RAM
ARM: shmobile: r8a7791 SYSC setup code
Signed-off-by: Olof Johansson <olof@lixom.net>
* Use shmobile_init_delay on r8a7790, r7s72100 and EMEV2 SoCs
* Remove unused redundant callbacks on EMEV2 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=UEEy
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-cleanup-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
Merge "Renesas ARM Based SoC Cleanup for v3.17" from Simon Horman:
- Use shmobile_init_delay on r8a7790, r7s72100 and EMEV2 SoCs
- Remove unused redundant callbacks on EMEV2 SoC
* tag 'renesas-soc-cleanup-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove unused r8a7790_init_early()
ARM: shmobile: Use r8a7790 DT CPU Frequency for Lager
ARM: shmobile: Use r8a7790 DT CPU Frequency in common case
ARM: shmobile: Use shmobile_init_delay() on r7s72100
ARM: shmobile: Use shmobile_init_delay() on Genmai boards
ARM: shmobile: Update r7s72100 DTS to include CPU frequency
ARM: shmobile: Get rid of redundant EMEV2 mach callbacks
ARM: shmobile: Use shmobile_init_delay() on EMEV2
ARM: shmobile: Update EMEV2 DTS to include CPU frequency
Signed-off-by: Olof Johansson <olof@lixom.net>
Move r8a7779 SoC and its Marzen board to use common clocks,
multiplatform and initialise SCIF (serial) devices using DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2zqe
-----END PGP SIGNATURE-----
Merge tag 'renesas-r8a7779-multiplatform-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Pull "Renesas ARM Based SoC r8a7779-multiplatform Updates for v3.17" from
Simon Horman:
Move r8a7779 SoC and its Marzen board to use common clocks,
multiplatform and initialise SCIF (serial) devices using DT.
* tag 'renesas-r8a7779-multiplatform-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (32 commits)
ARM: shmobile: marzen: Do not use workaround for scif devices
ARM: shmobile: marzen: Initialise SCIF devices using DT
ARM: shmobile: marzen: Remove early_printk from command line
ARM: shmobile: r8a7779: Add scif nodes to dtsi
ARM: shmobile: r8a7779 dtsi: Correct #address-cells/#size-cells for clocks
ARM: shmobile: r8a7779 dtsi: Update unit-addresses for clocks
ARM: shmobile: r8a7779: Remove unused r8a7779_init_delay()
ARM: shmobile: marzen-reference: Use DT CPU Frequency
ARM: shmobile: r8a7779: Use DT CPU Frequency in common case
ARM: shmobile: r8a7779: Add Maximum CPU Frequency to DTS
ARM: shmobile: marzen-reference: Remove legacy clock support
ARM: shmobile: Remove Marzen reference DTS
ARM: shmobile: Let Marzen multiplatform boot with Marzen DTB
ARM: shmobile: Remove non-multiplatform Marzen reference support
ARM: shmobile: marzen-reference: Instantiate clkdevs for SCIF and TMU
ARM: shmobile: marzen-reference: Initialize CPG device
ARM: shmobile: r8a7779: Initial multiplatform support
ARM: shmobile: marzen-reference: Move clock and OF device initialisation into board code
ARM: shmobile: r8a7779: Move r8a7779_earlytimer_init to clock-r8a7779.c
ARM: shmobile: r8a7779: Add helper to read mode pins
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Patch d6d757c9a4 ("ARM: shmobile: APMU: Add Core-Standby-state for
Suspend to RAM") added both an inline wrapper for shmobile_smp_apmu_suspend_init
and an empty function in arch/arm/mach-shmobile/platsmp-apmu.c. We get a
build failure when both are present, so this patch removes the one in the .c
file and keeps the inline version.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current fsi driver is using SNDRV_DMA_TYPE_CONTINUOUS
for snd_pcm_lib_preallocate_pages_for_all().
But, it came from original dma-sh7760.c,
and no longer needed.
This patch exchange its parameter, and removed
original dma mapping and un-needed
dma_sync_single_xxx() from driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Build the APMU for r8a7791 even though SMP is
disabled in the kernel config. Also initialize
Suspend-to-RAM from pm-r8a7791.c to in the future
cover both UP and SMP use cases of the APMU.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move r8a7791 specific reset vector setup code from the
SMP glue code to PM code. This makes the code one step
closer to allow PM operations such as Suspend-to-RAM
in the case when SMP is disabled in the kernel config.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
[horms+renesas@verge.net.au: updated for recent header file changes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Build the APMU for r8a7790 even though SMP is
disabled in the kernel config. Also initialize
Suspend-to-RAM from pm-r8a7790.c to in the future
cover both UP and SMP use cases of the APMU.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move r8a7790 specific reset vector setup code from the
SMP glue code to PM code. This makes the code one step
closer to allow PM operations such as Suspend-to-RAM
in the case when SMP is disabled in the kernel config.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
[horms+renesas@verge.net.au: updated for recent #include changes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The function shmobile_smp_apmu_suspend_init() should
be put into the init section to not trigger section
mismatch warnings.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adjust the APMU code to allow build when CONFIG_SMP=n.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Allow build of platsmp.c and headsmp.S even though
SMP is disabled in the kernel configuration. With
this in place it is possible to share the reset
vector setup code with power management code that
needs to be built even though SMP is disabled.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change location of r8a7791.h so it can be included as "r8a7791.h"
instead of the old style <mach/r8a7791.h>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change location of r8a7779.h so it can be included as "r8a7779.h"
instead of the old style <mach/r8a7779.h>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change location of sh7372.h so it can be included as "sh7372.h"
instead of the old style <mach/sh7372.h>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change location of sh73a0.h so it can be included as "sh73a0.h"
instead of the old style <mach/sh73a0.h>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change location of r8a7790.h so it can be included as "r8a7790.h"
instead of the old style <mach/r8a7790.h>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change location of r8a7778.h so it can be included as "r8a7778.h"
instead of the old style <mach/r8a7778.h>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change location of r8a7740.h so it can be included as "r8a7740.h"
instead of the old style <mach/r8a7740.h>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change location of r8a73a4.h so it can be included as "r8a73a4.h"
instead of the old style <mach/r8a73a4.h>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change location of r7s72100.h so it can be included using "r7s72100.h"
instead of the old style <mach/r7s72100.h>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The following commit has removed ARCH_HAS_CPUFREQ config:
Commit: e49d9b375628e67c9a718f4befaa8e45e5fad21b
Subject: ARM: Remove ARCH_HAS_CPUFREQ config option
This patch removes the code that is using ARCH_HAS_CPUFREQ
in mach-shmobile.
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 5ea3b1b2f8 'cma: add placement specifier for "cma=" kernel parameter'
adds a new 'fixed' parameter to dma_contiguous_reserve_area(). Update
rcar_gen2_reserve() accordingly.
This fixes the following compilation error:
arch/arm/mach-shmobile/setup-rcar-gen2.c: In function ‘rcar_gen2_reserve’:
arch/arm/mach-shmobile/setup-rcar-gen2.c:182:10: error: too few arguments to function ‘dma_contiguous_reserve_area’
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
A first set of bug fixes that didn't make it for the merge window, and
two Kconfig cleanups that still make sense at this point. Unfortunately,
one of the two cleanups caused an unintended change in the original
version, so we had to revert one part of it and do some more testing
to ensure the rest is really fine. There was also a last-minute
rebase of the patches to remove another bad commit.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/Ylr
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A first set of bug fixes that didn't make it for the merge window, and
two Kconfig cleanups that still make sense at this point.
Unfortunately, one of the two cleanups caused an unintended change in
the original version, so we had to revert one part of it and do some
more testing to ensure the rest is really fine. There was also a
last-minute rebase of the patches to remove another bad commit"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: use menuconfig for sub-arch menus
ARM: multi_v7_defconfig: re-enable SDHCI drivers
ARM: EXYNOS: Fix compilation warning
ARM: exynos: move sysram info to exynos.c
ARM: dts: Specify the NAND ECC scheme explicitly on Armada 385 DB board
ARM: dts: Specify the NAND ECC scheme explicitly on Armada 375 DB board
ARM: exynos: cleanup kconfig option display
misc: vexpress: fix error handling vexpress_syscfg_regmap_init()
ARM: Remove ARCH_HAS_CPUFREQ config option
ARM: integrator: fix section mismatch problem
ARM: mvebu: DT: fix OpenBlocks AX3-4 RAM size
ARM: samsung: make SAMSUNG_DMADEV optional
remoteproc: da8xx: don't select CMA on no-MMU
bus/arm-cci: add dependency on OF && CPU_V7
ARM: keystone requires ARM_PATCH_PHYS_VIRT
ARM: omap2: fix am43xx dependency on l2x0 cache
The System Type menu is getting quite long with platforms and is
inconsistent in handling of sub-arch specific options. Tidy up the menu
by making platform options a menuconfig entry containing any platform
specific config items.
[arnd: change OMAP part according to suggestion from
Tony Lindgren <tony@atomide.com>]
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This config exists entirely to hide the cpufreq menu from the
kernel configuration unless a platform has selected it. Nothing
is actually built if this config is 'Y' and it just leads to more
patches that add a select under a platform Kconfig so that some
other CPUfreq option can be chosen. Let's remove the option so
that we can always enable CPUfreq drivers on ARM platforms.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that SCIF devices are initialised using DT it should
not be necessary to use the work around to provide clocks any more.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Initialise SCIF devices using DT when booting marzen
using multiplatform.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove the now unused r8a7779_init_delay() function.
Based on work for the r8a7740 SoC by Magnus Damm.
Cc: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Convert the Marzen DT reference board support to use shmobile_init_delay()
to be able to migrate away from per-SoC delay setup functions.
Based on work for the Armadillo800 EVA board by Magnus Damm.
Cc: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Convert the common C-code-less r8a7779 DT board support
to use shmobile_init_delay() to be able to migrate away
from per-SoC delay setup functions.
Based on work by Magnus dam for the r8a7740 SoC.
Cc: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Marzen DT reference is now only built for multiplatform
which means that CCF comes with the package. Remove unused legacy
code ifdefs to clean up the code.
Based on similar work for the Koelsch board by Magnus Damm.
Cc: Magnus Damm <damm@opensource.se>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Let the multiplatform Marzen support boot with the legacy DTS for
Marzen as well as the Marzen reference DTS.
Based on work for the Koelsch board by Laurent Pinchart.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that r8a7779 has CCF support remove the legacy Marzen reference
Kconfig bits CONFIG_MACH_MARZEN_REFERENCE for the non-multiplatform
case.
Starting from this commit Marzen board support is always enabled via
CONFIG_MACH_MARZEN, and CONFIG_ARCH_MULTIPLATFORM is used to select
between board-marzen.c and board-marzen-reference.c
The file board-marzen-reference.c can no longer be used together with
the legacy sh-clk clock framework, instead CCF is used.
Based on work for the Koelsch board by Laurent Pinchart.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the common clock framework is supported, the clock lookup
entries in clock-r8a7779.c are not registered anymore. Devices must
instead reference their clocks in the device tree. However, SCIF and CMT
devices are still instantiated through platform code, and thus need a
clock lookup entry.
Retrieve the SCIF and CMT clock entries by name and register clkdevs for
the corresponding devices. This will be removed when the SCIF and CMT
devices will be instantiated from the device tree.
Based on work for the Koelsch board by Laurent Pinchart.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On multiplatform kernels clocks are handled by the CCF CPG driver. It
must be explicitly initialized by a call to r8a7779_clocks_init() with
the value of the boot mode pins.
Based on similar work for the Koelsch board by Laurent Pinchart.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Marzen and r8a7779 to CONFIG_SHMOBILE_MULTI. At this
point CCF is not yet supported so you cannot run this code
yet. For CCF support to happen several different components
are needed, and this is one simple portion that moves us
forward. Other patches need to build on top of this one.
Marzen board support exists in 3 flavours:
1) SHMOBILE_MULTI, MACH_MARZEN - board-marzen-reference.c (CCF + DT)
2) SHMOBILE, MACH_MARZEN_REFERENCE - board-marzen-reference.c (DT)
3) SHMOBILE, MACH_MARZEN - board-marzen.c (legacy C code)
When CCF is done then 2) will be removed. When 1) includes same features
as 3) then 3) will be removed.
Based on work for the Koelsch and r8a7791 by Magnus Damm.
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move the clock initialisation and OF device population from
SoC to board code. This is in keeping with the pattern used by Lager.
And the clock portion is part of decoupling clock initialisation
from SoC code in preparation for moving to the common clock framework.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
r8a7779_earlytimer_init() calls r8a7779_clock_init() and
r8a7779_clock_init() is defined in clock-r8a7779.c.
If both CONFIG_COMMON_CLK and CONFIG_ARCH_R8A7779 are enabled,
as will be the case when marzen-reference moves to use
the common clock framework, then setup-r8a7779.c is compiled
but clock-r8a7779.c is not.
As r8a7779_earlytimer_init() is not used by marzen-reference
simply move it to clock-r8a7779.c.
[horms+renesas@verge.net.au: rebase]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add and use helper to read mode pins.
This will be re-used when moving marzen-reference to
the common clock framework.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Geert Uytterhoeven