Symptoms were seen of the driver not having valid data for mailbox
commands. After debugging, the following sequence was found:
The driver maintains a port-wide pointer of the mailbox command that is
currently in execution. Once finished, the port-wide pointer is cleared
(done in lpfc_sli4_mq_release()). The next mailbox command issued will set
the next pointer and so on.
The mailbox response data is only copied if there is a valid port-wide
pointer.
In the failing case, it was seen that a new mailbox command was being
attempted in parallel with the completion. The parallel path was seeing
the mailbox no long in use (flag check under lock) and thus set the port
pointer. The completion path had cleared the active flag under lock, but
had not touched the port pointer. The port pointer is cleared after the
lock is released. In this case, the completion path cleared the just-set
value by the parallel path.
Fix by making the calls that clear mbox state/port pointer while under
lock. Also slightly cleaned up the error path.
Link: https://lore.kernel.org/r/20190922035906.10977-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When target-side fault injections are made, the driver isn't reconnecting
to the remote port. The driver is logging "2753" error messages which
state:
"PLOGI failure DID:1B2400 Status:x3/xf0240008"
The failures status is indicating a Illegal field error, which points to
the Temporary RPI field being used for the ELS. This error typically means
the driver used an RPI that was already registered (shouldn't be registered
if using it in this context).
Study has found that if the driver were in discovery attempts and
encountered an error, it wouldn't flag the temporary rpi in error. Yet the
rpi was released for reallocation in these error paths and another ELS
could allocate the rpi. In the failure situation a retry was done on an ELS
that had encountered an error, and as the rpi wasn't marked in error, the
ELS reused the rpi it originally allocated. But that rpi had been allocated
by a different ELS issued after the original error and before the retry
attempt. The different ELS had succeeded and the RPI was registered.
Fix by marking the rpi state for the node to be in error, aka as needing
reallocation, upon an error in the els processing. Error state marking is
always done prior to release back to the internal rpi free list, which the
driver wasn't doing in cases prior.
Also enhanced some of the logging to help in the next case of problem
troubleshooting.
Link: https://lore.kernel.org/r/20190922035906.10977-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A prior use-after-free mailbox fix solved it's problem by null'ing a ndlp
pointer. However, further testing has shown that this change causes a
later state change to occasionally be skipped, which results in a reference
count never being decremented thus the rpi is never released, which causes
a vport delete to never succeed.
Revise the fix in the prior patch to no longer null the ndlp. Instead the
RELEASE_RPI flag is set which will drive the release of the rpi.
Given the new code was added at a deep indentation level, refactor the code
block using a new routine that avoids the indentation issues.
Fixes: 9b16406864 ("scsi: lpfc: Fix use-after-free mailbox cmd completion")
Link: https://lore.kernel.org/r/20190922035906.10977-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The nvme-fc transport may call to abort an io on controller reset. If the
driver is out of resources to issue an abort command, it just gives up and
does nothing. The transport expects the lldd to always be able to terminate
an io it has issued. At that point, the controller hangs waiting for
aborted ios to be returned. Note: flaged by "6136" and "6176" error
messages.
Root issue was the adapter mis-allocated the number resources it allocated
for command entries for the adapter.
Convert the driver to allocate command resources based on the number of
xris supported by the FC port - 1 resource for the original command and 1
resource for the abort request.
Link: https://lore.kernel.org/r/20190922035906.10977-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use of spin_lock_irq may re-enable interrupts prematurely.
Convert to spin_lock. Note: code is under the phba->hba_lock which has been
locked with irqsave.
Link: https://lore.kernel.org/r/20190922035906.10977-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A recent patch unconditionally marks the hba as in error as part of
resetting the adapter. The driver flow that called the adapter reset was a
recovery path, which expects the adapter to not be in an error state in
order to finish the recovery. Given the new error state being set, the
recovery fails and the adapter is left in limbo.
Revise the adapter reset routine so that it will only mark the adapter in
error if it was unable to reset the adapter.
Fixes: 8c24a4f643 ("scsi: lpfc: Fix crash due to port reset racing vs adapter error handling")
Link: https://lore.kernel.org/r/20190903215441.10490-1-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert the remaining %pf users to %ps to prepare for the removal of the
old %pf conversion specifier support.
Fixes: 3235066449 ("scsi: lpfc: Migrate to %px and %pf in kernel print calls")
Link: https://lore.kernel.org/r/20190904160423.3865-1-sakari.ailus@linux.intel.com
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 12.4.0.0 patch that merged WQ/CQ pairs into single per-cpu pair
contained a bug: a local variable was set to the queue pair by index. This
should have allowed the local variable to be natively used. Instead, the
code reused the index relative to the local variable, obtaining a random
pointer value that when used eventually faulted the system
Convert offending code to use local variable.
Fixes: c00f62e6c5 ("scsi: lpfc: Merge per-protocol WQ/CQ pairs into single per-cpu pair")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, each hardware queue, typically allocated per-cpu, consists of a
WQ/CQ pair per protocol. Meaning if both SCSI and NVMe are supported 2
WQ/CQ pairs will exist for the hardware queue. Separate queues are
unnecessary. The current implementation wastes memory backing the 2nd set
of queues, and the use of double the SLI-4 WQ/CQ's means less hardware
queues can be supported which means there may not always be enough to have
a pair per cpu. If there is only 1 pair per cpu, more cpu's may get their
own WQ/CQ.
Rework the implementation to use a single WQ/CQ pair by both protocols.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Typical SLI-4 hardware supports up to 2 4KB pages to be registered per XRI
to contain the exchanges Scatter/Gather List. This caps the number of SGL
elements that can be in the SGL. There are not extensions to extend the
list out of the 2 pages.
The G7 hardware adds a SGE type that allows the SGL to be vectored to a
different scatter/gather list segment. And that segment can contain a SGE
to go to another segment and so on. The initial segment must still be
pre-registered for the XRI, but it can be a much smaller amount (256Bytes)
as it can now be dynamically grown. This much smaller allocation can
handle the SG list for most normal I/O, and the dynamic aspect allows it to
support many MB's if needed.
The implementation creates a pool which contains "segments" and which is
initially sized to hold the initial small segment per xri. If an I/O
requires additional segments, they are allocated from the pool. If the
pool has no more segments, the pool is grown based on what is now
needed. After the I/O completes, the additional segments are returned to
the pool for use by other I/Os. Once allocated, the additional segments are
not released under the assumption of "if needed once, it will be needed
again". Pools are kept on a per-hardware queue basis, which is typically
1:1 per cpu, but may be shared by multiple cpus.
The switch to the smaller initial allocation significantly reduces the
memory footprint of the driver (which only grows if large ios are
issued). Based on the several K of XRIs for the adapter, the 8KB->256B
reduction can conserve 32MBs or more.
It has been observed with per-cpu resource pools that allocating a resource
on CPU A, may be put back on CPU B. While the get routines are distributed
evenly, only a limited subset of CPUs may be handling the put routines.
This can put a strain on the lpfc_put_cmd_rsp_buf_per_cpu routine because
all the resources are being put on a limited subset of CPUs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added code to support driver loopback with MDS Diagnostics. This style of
diagnostics passes frames from the fabric to the driver who then echo them
back out the link. SEND_FRAME WQEs are used to transmit the frames. Added
the SOF and EOF field location definitions for use by SEND_FRAME.
Also ensure that enable_mds_diags is a RW parameter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In order to see real addresses, convert %p with %px for kernel addresses
and replace %p with %pf for functions.
While converting, standardize on "x%px" throughout (not %px or 0x%px).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Running on Coverity produced the following errors:
- coding style (indentation)
- memset size mismatch errors
note: comment cases where it is purposely a mismatch
Fix the errors.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As part of firmware download, the adapter is reset. On the adapter the
reset causes the function to stop and all outstanding io is terminated
(without responses). The reset path then starts teardown of the adapter,
starting with deregistration of the remote ports with the nvme-fc
transport. The local port is then deregistered and the driver waits for
local port deregistration. This never finishes.
The remote port deregistrations terminated the nvme controllers, causing
them to send aborts for all the outstanding io. The aborts were serviced in
the driver, but stalled due to its state. The nvme layer then stops to
reclaim it's outstanding io before continuing. The io must be returned
before the reset on the controller is deemed complete and the controller
delete performed. The remote port deregistration won't complete until all
the controllers are terminated. And the local port deregistration won't
complete until all controllers and remote ports are terminated. Thus things
hang.
The issue is the reset which stopped the adapter also stopped all the
responses that would drive i/o completions, and the aborts were also
stopped that stopped i/o completions. The driver, when resetting the
adapter like this, needs to be generating the completions as part of the
adapter reset so that I/O complete (in error), and any aborts are not
queued.
Fix by adding flush routines whenever the adapter port has been reset or
discovered in error. The flush routines will generate the completions for
the scsi and nvme outstanding io. The abort ios, if waiting, will be caught
and flushed as well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the adapter encounters a condition which causes the adapter to fail
(driver must detect the failure) simultaneously to a request to the driver
to reset the adapter (such as a host_reset), the reset path will be racing
with the asynchronously-detect adapter failure path. In the failing
situation, one path has started to tear down the adapter data structures
(io_wq's) while the other path has initiated a repeat of the teardown and
is in the lpfc_sli_flush_xxx_rings path and attempting to access the
just-freed data structures.
Fix by the following:
- In cases where an adapter failure is detected, rather than explicitly
calling offline_eratt() to start the teardown, change the adapter state
and let the later calls of posted work to the slowpath thread invoke the
adapter recovery. In essence, this means all requests to reset are
serialized on the slowpath thread.
- Clean up the routine that restarts the adapter. If there is a failure
from brdreset, don't immediately error and leave things in a partial
state. Instead, ensure the adapter state is set and finish the teardown
of structures before returning.
- If in the scsi host reset handler and the board fails to reset and
restart (which can be due to parallel reset/recovery paths), instead of
hard failing and explicitly calling offline_eratt() (which gets into the
redundant path), just fail out and let the asynchronous path resolve the
adapter state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In tests with remote ports contantly logging out/logging coupled with
occassional local link bounce, if a remote port is disocnnected for longer
than devloss_tmo and then subsequently reconnected, eventually the test
will fail to login with the remote port and remote port connectivity is
lost.
When devloss_tmo expires, the driver does not free the node struct until
the port or npiv instances is being deleted. The node is left allocated but
the state set to UNUSED. If the node was in the process of logging in when
the local link drop occurred, meaning the RPI was allocated for the node in
order to send the ELS, but not yet registered which comes after successful
login, the node is moved to the NPR state, and if devloss expires, to
UNUSED state. If the remote port comes back, the node associated with it
is restarted and this path happens to allocate a new RPI and overwrites the
prior RPI value. In the cases where the port was logged in and loggs out,
the path did release the RPI but did not set the node rpi value. In the
cases where the remote port never finished logging in, the path never did
the call to release the rpi. In this latter case, when the node is
subsequently restore, the new rpi allocation overwrites the rpi that was
not released, and the rpi is now leaked. Eventually the port will run out
of RPI resources to log into new remote ports.
Fix by following changes:
- When an rpi is released, do so under locks and ensure the node rpi value
is set to a non-allocated value (LPFC_RPI_ALLOC_ERROR). Note:
refactored to a small service routine to avoid indentation issues.
- When re-enabling a node, check the rpi value to determine if a new
allocation is necessary. If already set, use the prior rpi.
Enhanced logging to help in the future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The adapter reset path (lpfc_sli_hba_down) is taking/releasing a lock with
irq. But, the path is already under the hbalock which raised irq so it's
unnecessary.
Convert to simple lock/unlock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the adapter is reset while there are outstanding ELS's, subsequent
reinitialization of the adapter will fail as it has not recovered all of
the io contexts relative to the ELS's.
If an ELS timed out or otherwise failed and an the ELS was attempted to be
aborted (which changes the ELS completion context), in causes where the
driver generates completions for the outstanding IO as the adapter would
not due to being reset, the driver released only the ELS context and failed
to release the abort context. When the adapter went to reinit, as it had
not received all of the contexts, it failed to reinit.
Fix by having the ELS completion handler identify the driver-generated
completion status and release the abort context.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When connected to a high number of remote ports, the driver is encountering
PLOGI errors. The errors are due to adapter detected failures indicating
illegal field values.
Turns out the driver was prematurely clearing an RPI bitmask before waiting
for an UNREG_RPI mailbox completion. This allowed the RPI to be reused
before it was actually available.
Fix by clearing RPI bitmask only after UNREG_RPI mailbox completion.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the redundant initialization code.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTl4yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdcxAQDCJVbd
fPUX76/V1ldupunF97+3DTharxxbst+VnkOnCwD8D4c0KFFFOI9+F36cnMGCPegE
fjy17dQLvsJ4GsidHy8=
=aS5B
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
The big merge conflict this time around is the SPDX licence tags.
Following discussion on linux-next, we believe our version to be more
accurate than the one in the tree, so the resolution is to take our
version for all the SPDX conflicts"
Note on the SPDX license tag conversion conflicts: the SCSI tree had
done its own SPDX conversion, which in some cases conflicted with the
treewide ones done by Thomas & co.
In almost all cases, the conflicts were purely syntactic: the SCSI tree
used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the
treewide conversion had used the new-style ones ("GPL-2.0-only" and
"GPL-2.0-or-later").
In these cases I picked the new-style one.
In a few cases, the SPDX conversion was actually different, though. As
explained by James above, and in more detail in a pre-pull-request
thread:
"The other problem is actually substantive: In the libsas code Luben
Tuikov originally specified gpl 2.0 only by dint of stating:
* This file is licensed under GPLv2.
In all the libsas files, but then muddied the water by quoting GPLv2
verbatim (which includes the or later than language). So for these
files Christoph did the conversion to v2 only SPDX tags and Thomas
converted to v2 or later tags"
So in those cases, where the spdx tag substantially mattered, I took the
SCSI tree conversion of it, but then also took the opportunity to turn
the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag.
Similarly, when there were whitespace differences or other differences
to the comments around the copyright notices, I took the version from
the SCSI tree as being the more specific conversion.
Finally, in the spdx conversions that had no conflicts (because the
treewide ones hadn't been done for those files), I just took the SCSI
tree version as-is, even if it was old-style. The old-style conversions
are perfectly valid, even if the "-only" and "-or-later" versions are
perhaps more descriptive.
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits)
scsi: qla2xxx: move IO flush to the front of NVME rport unregistration
scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition
scsi: qla2xxx: on session delete, return nvme cmd
scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices
scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1
scsi: megaraid_sas: Introduce various Aero performance modes
scsi: megaraid_sas: Use high IOPS queues based on IO workload
scsi: megaraid_sas: Set affinity for high IOPS reply queues
scsi: megaraid_sas: Enable coalescing for high IOPS queues
scsi: megaraid_sas: Add support for High IOPS queues
scsi: megaraid_sas: Add support for MPI toolbox commands
scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver
scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura
scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD
scsi: megaraid_sas: Handle sequence JBOD map failure at driver level
scsi: megaraid_sas: Don't send FPIO to RL Bypass queue
scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault
scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout
scsi: megaraid_sas: Call disable_irq from process IRQ poll
scsi: megaraid_sas: Remove few debug counters from IO path
...
This patch adds general RSCN support:
- The ability to transmit an RSCN to the port on the other end of
the link (regular port if pt2pt, or fabric controller if fabric).
- And general recognition of an RSCN ELS when an ELS is received.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fix sparse warnings:
drivers/scsi/lpfc/lpfc_sli.c:115:1: warning: symbol 'lpfc_sli4_pcimem_bcopy' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_sli.c:7854:1: warning: symbol 'lpfc_sli4_process_missed_mbox_completions' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:223:27: warning: symbol 'lpfc_nvmet_get_ctx_for_xri' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:245:27: warning: symbol 'lpfc_nvmet_get_ctx_for_oxid' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_init.c:75:10: warning: symbol 'lpfc_present_cpu' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While fixing the resources per socket, realized the driver was not using
hardware queues (up to 1 per cpu) if there were fewer interrupt
vectors. The driver was only using the hardware queue assigned to the cpu
with the vector.
Rework the affinity map check to use the additional hardware queue elements
that had been allocated. If the cpu count exceeds the hardware queue count
- share, but choose what is shared with by: hyperthread peer, core peer,
socket peer, or finally similar cpu in a different socket.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
eq create is leaking mailbox memory if it encounters an error.
rework error path to free the memory.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver is notified of new command frame receipt by CQEs. As
part of the CQE processing, the driver upcalls the nvmet_fc transport to
deliver the command. nvmet_fc, as part of receiving the command builds out
a context for it, where one of the first steps is to allocate memory for
the io.
When running with tests that do large ios (1MB), it was found on some
systems, the total number of outstanding I/O's, at 1MB per, completely
consumed the system's memory. Thus additional ios were getting blocked in
the memory allocator. Given that this blocked the lpfc thread processing
CQEs, there were lots of other commands that were received and which are
then held up, and given CQEs are serially processed, the aggregate delays
for an IO waiting behind the others became cummulative - enough so that the
initiator hit timeouts for the ios.
The basic fix is to avoid the direct upcall and instead schedule a work
item for each io as it is received. This allows the cq processing to
complete very quickly, and each io can then run or block on it's own.
However, this general solution hurts latency when there are few ios. As
such, implemented the fix such that the driver watches how many CQEs it has
processed sequentially in one run. As long as the count is below a
threshold, the direct nvmet_fc upcall will be made. Only when the count is
exceeded will it revert to work scheduling.
Given that debug of this showed a surprisingly long delay in cq processing,
the io timer stats were updated to better reflect the processing of the
different points.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There were a number of erroneous comments and incorrect older lockdep
checks that were causing a number of warnings.
Resolve the following:
- Inconsistent lock state warnings in lpfc_nvme_info_show().
- Fixed comments and code on sequences where ring lock is now held instead
of hbalock.
- Reworked calling sequences around lpfc_sli_iocbq_lookup(). Rather than
locking prior to the routine and have routine guess on what lock, take
the lock within the routine. The lockdep check becomes unnecessary.
- Fixed comments and removed erroneous hbalock checks.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Bart Van Assche <bvanassche@acm.org>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that a kernel warning appears when smp_processor_id() is
called with preempt debugging enabled.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove those functions that are not called from outside the removed
functions.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoid that smatch complains about misleading indentation.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler complains about missing declarations
when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Declaring interrupt clear routines as inline is bogus as they are used as
an indirect pointer.
Remove the inline references.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
You can't declare a function inline in a header if it doesn't have a body
available to the compiler. So realistically you either don't declare it
inline or you make it a static inline in the header. I think the latter
applies in this case, so this should be the fix
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change the SLI4 queue creation code to use NUMA node based memory
allocation based on the cpu the queues will be related to.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver maintains a sideband structure which has a pointer for
each queue element. However, at 8 bytes per pointer, and up to 4k elements
per queue, and 100s of queues, this can take up a lot of memory.
Convert the driver to using an access routine that calculates the element
address based on its index rather than using the pointer table.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently reporting the firmware revision not the actual boot
bios version in FDMI data.
Modify the driver to obtain the boot bios version from the adapter and use
that data in the FMDI data sent to the switch.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The adapter initialization sequence enables interrupts, initializes the
adapter link_state to LINK_DOWN, then issues commands to initialize the
adapter. The interrupt handler on the adapter validates the link_state (has
to be at least LINK_DOWN) and if invalid, will discard the interrupting
event.
In most cases, there is not a command completion, thus an interrupt until
the initialization commands have been sent which is post the setting of
state to LINK_DOWN. However, in cases of firmware reset, the reset will
modify the link_state to an invalid value (indicating a reset of the
adapter) and there occasionally are cases where the adapter will generate
an asynchronous event which shares the eq/cq used for mailbox commands. In
the failure case, an interrupt is generated immediately after enabling them
due to the async event. As link_state is invalid, the eq is list and the
CQ not serviced. At this point link_state is initialized and the mailbox
command sent. As the CQ has not been serviced, it is not armed, so no
interrupt event is generated when the mailbox command completes.
Modify the initialization sequence so that interrupts are enabled after
link_state is properly initialized, which avoids the race condition with
the async event.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code is using msleep when polling for hw ready. Unfortunately the
msleep routine isn't very accurate on rescheduling. In fact, on a busy
systems which reset the adapter, it became 10s of seconds before it was
rescheduled.
Fix by busy waiting using udelay. As we're now busy waiting, significantly
reduce the wait time so that we can exit the pool loop as soon as possible.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver periodically checks for adapter error in a background thread. If
the thread detects an error, the adapter will be reset including the
deletion and reallocation of workqueues on the adapter. Simultaneously,
there may be a user-space request to offline the adapter which may try to
do many of the same steps, in parallel, on a different thread. As memory
was deallocated while unexpected, the parallel offline request hit a bad
pointer.
Add coordination between the two threads. The error recovery thread has
precedence. So, when an error is detected, a flag is set on the adapter to
indicate the error thread is terminating the adapter. But, before doing
that work, it will look for a flag that is set by the offline flow, and if
set, will wait for it to complete before then processing the error handling
path. Similarly, in the offline thread, it first checks for whether the
error thread is resetting the adapter, and if so, will then wait for the
error thread to finish. Only after it has finished, will it set its flag
and offline the adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a couple of cases, the driver detected a pci error (via pci device state
or via failed register reads) but didn't take any action to disable the
device. Additionally, the driver is ignoring the status of pci
configuration space reads.
Having the driver take the adapter offline whenever the pci error is
detected. Pay attention to pci_config_space_read status and return failure
if an error is seen.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With negative test injection, the driver is receiving a command with first
burst enabled, meaning Sequence initiative is not passed with the command
frame. The driver notes the condition and discards the frame. However the
driver calls the incorrect buffer free routine, resulting in a NULL pointer
reference.
For hbq buffer free, convert to using lpfc_rq_buf_free().
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When unloading the driver, mailbox commands may be sent without holding a
reference on the ndlp. By the time the mailbox command completes, the ndlp
may have reduced its ref counts and been freed. The problem was reported
by KASAN.
While unregistering due to driver unload, have the completion noop'd by
setting the ndlp context NULL'd. Due to the unload, no further action was
necessary. Also, while reviewing this path, the generic nulling of the
context after handling should be slightly moved.
Reported by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the final round of mostly small fixes and performance
improvements to our initial submit. The main regression fix is the
ia64 simscsi build failure which was missed in the serial number
elimination conversion.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIxBayYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pisherpAP4rxLpX
bcUnQnEsvoxys/JyoK08Qfv1JebZo1B2MAZ62wD/VZ7LpOuzVLhsM2KhLFGRrs1/
7D2K4tgtO2dQsFix7H0=
=pcHl
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the final round of mostly small fixes and performance
improvements to our initial submit.
The main regression fix is the ia64 simscsi build failure which was
missed in the serial number elimination conversion"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: ia64: simscsi: use request tag instead of serial_number
scsi: aacraid: Fix performance issue on logical drives
scsi: lpfc: Fix error codes in lpfc_sli4_pci_mem_setup()
scsi: libiscsi: Hold back_lock when calling iscsi_complete_task
scsi: hisi_sas: Change SERDES_CFG init value to increase reliability of HiLink
scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of STP target port
scsi: hisi_sas: Set PHY linkrate when disconnected
scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw
scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
scsi: hisi_sas: Change return variable type in phy_up_v3_hw()
scsi: qla2xxx: check for kstrtol() failure
scsi: lpfc: fix 32-bit format string warning
scsi: lpfc: fix unused variable warning
scsi: target: tcmu: Switch to bitmap_zalloc()
scsi: libiscsi: fall back to sendmsg for slab pages
scsi: qla2xxx: avoid printf format warning
scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset
scsi: lpfc: Correct __lpfc_sli_issue_iocb_s4 lockdep check
scsi: ufs: hisi: fix ufs_hba_variant_ops passing
scsi: qla2xxx: Fix panic in qla_dfs_tgt_counters_show
...
This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core. Additionally Christoph
refactored gdth as part of the dma changes. The major mid-layer
change this time is the removal of bidi commands and with them the
whole of the osd/exofs driver and filesystem.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIC54SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishT1GAPwJEV23
ExPiPsnuVgKj49nLTagZ3rILRQcYNbL+MNYqxQEA0cT8FHzSDBfWY5OKPNE+RQ8z
f69LpXGmMpuagKGvvd4=
=Fhy1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
The outer routine lpfc_sli_issue_iocb(), which decomposes into the
SLI3 (s3) or SLI4 (s4) subroutines takes out the locks. For s3, it takes
out the hbalock. For s4, it takes out the ring_lock. The lockdep check in
the s3 and s4 subroutines both check hbalock, which is incorrect for s4.
Revise the s4 subroutine to lockdep check the ring_lock.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are a handful of statements that are indented incorrectly. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For files modified as part of 12.2.0.0 patches, update copyright to 2019
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A scsi host lock is taken on every io completion to check whether the abort
handler is waiting on the io completion. This is an expensive lock to take
on all completion when rarely in an abort condition.
Replace scsi host lock with command-specific lock. Synchronize completion
and abort paths by new cmd lock. Ensure all flag changing and nulling of
context pointers taken under lock. When adding lock to task management
abort, realized it was missing other synchronization locks. Added that
synchronization to match normal paths.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driving high iop counts, auto_imax coalescing kicks in and drives the
performance to extremely small iops levels.
There are two issues:
1) auto_imax is enabled by default. The auto algorithm, when iops gets
high, divides the iops by the hdwq count and uses that value to
calculate EQ_Delay. The EQ_Delay is set uniformly on all EQs whether
they have load or not. The EQ_delay is only manipulated every 5s (a
long time). Thus there were large 5s swings of no interrupt delay
followed by large/maximum delay, before repeating.
2) When processing a CQ, the driver got mixed up on the rate of when
to ring the doorbell to keep the chip appraised of the eqe or cqe
consumption as well as how how long to sit in the thread and
process queue entries. Currently, the driver capped its work at
64 entries (very small) and exited/rearmed the CQ. Thus, on heavy
loads, additional overheads were taken to exit and re-enter the
interrupt handler. Worse, if in the large/maximum coalescing
windows,k it could be a while before getting back to servicing.
The issues are corrected by the following:
- A change in defaults. Auto_imax is turned OFF and fcp_imax is set
to 0. Thus all interrupts are immediate.
- Cleanup of field names and their meanings. Existing names were
non-intuitive or used for duplicate things.
- Added max_proc_limit field, to control the length of time the
handlers would service completions.
- Reworked EQ handling:
Added common routine that walks eq, applying notify interval and max
processing limits. Use queue_claimed to claim ownership of the queue
while processing. Always rearm the queue whenever the common routine
is called.
Rework queue element processing, namely to eliminate hba_index vs
host_index. Only one index is necessary. The queue entry can be
marked invalid and the host_index updated immediately after eqe
processing.
After rework, xx_release routines are now DB write functions. Renamed
the routines as such.
Moved lpfc_sli4_eq_flush(), which does similar action, to same area.
Replaced the 2 individual loops that walk an eq with a call to the
common routine.
Slightly revised lpfc_sli4_hba_handle_eqe() calling syntax.
Added per-cpu counters to detect interrupt rates and scale
interrupt coalescing values.
- Reworked CQ handling:
Added common routine that walks cq, applying notify interval and max
processing limits. Use queue_claimed to claim ownership of the queue
while processing. Always rearm the queue whenever the common routine
is called.
Rework queue element processing, namely to eliminate hba_index vs
host_index. Only one index is necessary. The queue entry can be
marked invalid and the host_index updated immediately after cqe
processing.
After rework, xx_release routines are now DB write functions. Renamed
the routines as such.
Replaced the 3 individual loops that walk a cq with a call to the
common routine.
Redefined lpfc_sli4_sp_handle_mcqe() to commong handler definition with
queue reference. Add increment for mbox completion to handler.
- Added a new module/sysfs attribute: lpfc_cq_max_proc_limit To allow
dynamic changing of the CQ max_proc_limit value being used.
Although this leaves an EQ as an immediate interrupt, that interrupt will
only occur if a CQ bound to it is in an armed state and has cqe's to
process. By staying in the cq processing routine longer, high loads will
avoid generating more interrupts as they will only rearm as the processing
thread exits. The immediately interrupt is also beneficial to idle or
lower-processing CQ's as they get serviced immediately without being
penalized by sharing an EQ with a more loaded CQ.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Review of the eq coalescing logic showed the code was a bit fragmented.
Sometimes it would save/set via an interrupt max value, while in others it
would do so via a usdelay. There were also two places changing eq delay,
one place that issued mailbox commands, and another that changed via
register writes if supported.
Clean this up by:
- Standardizing the operation of lpfc_modify_hba_eq_delay() routine so
that it is always told of a us delay to impose. The routine then chooses
the best way to set that - via register or via mbx.
- Rather than two value types stored in eq->q_mode (usdelay if change via
register, imax if change via mbox) - q_mode always contains usdelay.
Before any value change, old vs new value is compared and only if
different is a change done.
- Revised the dmult calculation. dmult is not set based on overall imax
divided by hardware queues - instead imax applies to a single cpu and
the value will be replicated to all cpus.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
So far MSIX vector allocation assumed it would be 1:1 with hardware
queues. However, there are several reasons why fewer MSIX vectors may be
allocated than hardware queues such as the platform being out of vectors or
adapter limits being less than cpu count.
This patch reworks the MSIX/EQ relationships with the per-cpu hardware
queues so they can function independently. MSIX vectors will be equitably
split been cpu sockets/cores and then the per-cpu hardware queues will be
mapped to the vectors most efficient for them.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Default behavior is to use the information from the upper IO stacks to
select the hardware queue to use for IO submission. Which typically has
good cpu affinity.
However, the driver, when used on some variants of the upstream kernel, has
found queuing information to be suboptimal for FCP or IO completion locked
on particular cpus.
For command submission situations, the lpfc_fcp_io_sched module parameter
can be set to specify a hardware queue selection policy that overrides the
os stack information.
For IO completion situations, rather than queing cq processing based on the
cpu servicing the interrupting event, schedule the cq processing on the cpu
associated with the hardware queue's cq.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The XRI get/put lists were partitioned per hardware queue. However, the
adapter rarely had sufficient resources to give a large number of resources
per queue. As such, it became common for a cpu to encounter a lack of XRI
resource and request the upper io stack to retry after returning a BUSY
condition. This occurred even though other cpus were idle and not using
their resources.
Create as efficient a scheme as possible to move resources to the cpus that
need them. Each cpu maintains a small private pool which it allocates from
for io. There is a watermark that the cpu attempts to keep in the private
pool. The private pool, when empty, pulls from a global pool from the
cpu. When the cpu's global pool is empty it will pull from other cpu's
global pool. As there many cpu global pools (1 per cpu or hardware queue
count) and as each cpu selects what cpu to pull from at different rates and
at different times, it creates a radomizing effect that minimizes the
number of cpu's that will contend with each other when the steal XRI's from
another cpu's global pool.
On io completion, a cpu will push the XRI back on to its private pool. A
watermark level is maintained for the private pool such that when it is
exceeded it will move XRI's to the CPU global pool so that other cpu's may
allocate them.
On NVME, as heartbeat commands are critical to get placed on the wire, a
single expedite pool is maintained. When a heartbeat is to be sent, it will
allocate an XRI from the expedite pool rather than the normal cpu
private/global pools. On any io completion, if a reduction in the expedite
pools is seen, it will be replenished before the XRI is placed on the cpu
private pool.
Statistics are added to aid understanding the XRI levels on each cpu and
their behaviors.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SLI4 nvme functions are passing the SLI3 ring number when posting wqe to
hardware. This should be indicating the hardware queue to use, not the ring
number.
Replace ring number with the hardware queue that should be used.
Note: SCSI avoided this issue as it utilized an older lfpc_issue_iocb
routine that properly adapts.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Both NVME and SCSI aborts are now processed off the CQ workqueue and do not
generate events for the slowpath any more.
Remove the unused event code.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Once the IO buff allocations were made shared, there was a single XRI
buffer list shared by all hardware queues. A single list isn't great for
performance when shared across the per-cpu hardware queues.
Create a separate XRI IO buffer get/put list for each Hardware Queue. As
SGLs and associated IO buffers get allocated/posted to the firmware; round
robin their assignment across all available hardware Queues so that there
is an equitable assignment.
Modify SCSI and NVME IO submit code paths to use the Hardware Queue logic
for XRI allocation.
Add a debugfs interface to display hardware queue statistics
Added new empty_io_bufs counter to track if a cpu runs out of XRIs.
Replace common_ variables/names with io_ to make meanings clearer.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, both nvme and fcp each have their own concept of an io_channel,
which is a combination wq/cq and associated msix. Different cpus would
share an io_channel.
The driver is now moving to per-cpu wq/cq pairs and msix vectors. The
driver will still use separate wq/cq pairs per protocol on each cpu, but
the protocols will share the msix vector.
Given the elimination of the nvme and fcp io channels, the module
parameters will be removed. A new parameter, lpfc_hdw_queue is added which
allows the wq/cq pair allocation per cpu to be overridden and allocated to
lesser value. If lpfc_hdw_queue is zero, the number of pairs allocated will
be based on the number of cpus. If non-zero, the parameter specifies the
number of queues to allocate. At this time, the maximum non-zero value is
64.
To manage this new paradigm, a new hardware queue structure is created to
track queue activity and relationships.
As MSIX vector allocation must be known before setting up the
relationships, msix allocation now occurs before queue datastructures are
allocated. If the number of vectors allocated is less than the desired
hardware queues, the hardware queue counts will be reduced to the number of
vectors
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a extra queue and msix vector for expresslane. Now that the driver
will be doing queues per cpu, this oddball queue is no longer needed.
Expresslane will utilize the normal per-cpu queues.
Updated debugfs sli4 queue output to go along with the change
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, both NVME and SCSI get their IO buffers from separate
pools. XRI's are associated 1:1 with IO buffers, so XRI's are also split
between protocols.
Eliminate the independent pools and use a single pool. Each buffer
structure now has a common section and a protocol section. Per protocol
routines for SGL initialization are removed and replaced by common
routines. Initialization of the buffers is only done on the common area.
All other fields, which are protocol specific, are initialized when the
buffer is allocated for use in the per-protocol allocation routine.
In the past, the SCSI side allocated IO buffers as part of slave_alloc
calls until the maximum XRIs for SCSI was reached. As all XRIs are now
common and may be used for either protocol, allocation for everything is
done as part of adapter initialization and the scsi side has no action in
slave alloc.
As XRI's are no longer split, the lpfc_xri_split module parameter is
removed.
Adapters based on SLI3 will continue to use the older scsi_buf_list_get/put
routines. All SLI4 adapters utilize the new IO buffer scheme
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A set of 17 fixes. Most of these are minor or trivial. The one fix
that may be serious is the isci one: the bug can cause hba parameters
to be set from uninitialized memory. I don't think it's exploitable,
but you never know.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXEKL0SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishVZpAQCwuPTk
fqOt4v4hJ0oUHtEBsQK3VMXSdUvWdb5Lbn3WeQD/RFYTyNxcIF7ADSWw71b+IigT
ejUrMzI8ig+nZ1jbFZ4=
=BdS/
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A set of 17 fixes. Most of these are minor or trivial.
The one fix that may be serious is the isci one: the bug can cause hba
parameters to be set from uninitialized memory. I don't think it's
exploitable, but you never know"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxgb4i: add wait_for_completion()
scsi: qla1280: set 64bit coherent mask
scsi: ufs: Fix geometry descriptor size
scsi: megaraid_sas: Retry reads of outbound_intr_status reg
scsi: qedi: Add ep_state for login completion on un-reachable targets
scsi: ufs: Fix system suspend status
scsi: qla2xxx: Use correct number of vectors for online CPUs
scsi: hisi_sas: Set protection parameters prior to adding SCSI host
scsi: tcmu: avoid cmd/qfull timers updated whenever a new cmd comes
scsi: isci: initialize shost fully before calling scsi_add_host()
scsi: lpfc: lpfc_sli: Mark expected switch fall-throughs
scsi: smartpqi_init: fix boolean expression in pqi_device_remove_start
scsi: core: Synchronize request queue PM status only on successful resume
scsi: pm80xx: reduce indentation
scsi: qla4xxx: check return code of qla4xxx_copy_from_fwddb_param
scsi: megaraid_sas: correct an info message
scsi: target/iscsi: fix error msg typo when create lio_qr_cache failed
scsi: sd: Fix cache_type_store()
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "Drop thru" and "Fall
Thru" with "fall through" annotations, which is what GCC is expecting to
find.
Also, in some cases a dash is added as a token in order to separate the
"fall through" annotation from the rest of the comment on the same line,
which is what GCC is expecting to find.
Addresses-Coverity-ID: 114979 ("Missing break in switch")
Addresses-Coverity-ID: 114980 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas. Additionally, we have
a pile of annotation, unused variable and minor updates. The big API
change is the updates for Christoph's DMA rework which include
removing the DISABLE_CLUSTERING flag. And finally there are a couple
of target tree updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXCEUNiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdjKAP9vrTTv
qFaYmAoRSbPq9ZiixaXLMy0K/6o76Uay0gnBqgD/fgn3jg/KQ6alNaCjmfeV3wAj
u1j3H7tha9j1it+4pUw=
=GDa+
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas.
Additionally, we have a pile of annotation, unused variable and minor
updates.
The big API change is the updates for Christoph's DMA rework which
include removing the DISABLE_CLUSTERING flag.
And finally there are a couple of target tree updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (259 commits)
scsi: isci: request: mark expected switch fall-through
scsi: isci: remote_node_context: mark expected switch fall-throughs
scsi: isci: remote_device: Mark expected switch fall-throughs
scsi: isci: phy: Mark expected switch fall-through
scsi: iscsi: Capture iscsi debug messages using tracepoints
scsi: myrb: Mark expected switch fall-throughs
scsi: megaraid: fix out-of-bound array accesses
scsi: mpt3sas: mpt3sas_scsih: Mark expected switch fall-through
scsi: fcoe: remove set but not used variable 'port'
scsi: smartpqi: call pqi_free_interrupts() in pqi_shutdown()
scsi: smartpqi: fix build warnings
scsi: smartpqi: update driver version
scsi: smartpqi: add ofa support
scsi: smartpqi: increase fw status register read timeout
scsi: smartpqi: bump driver version
scsi: smartpqi: add smp_utils support
scsi: smartpqi: correct lun reset issues
scsi: smartpqi: correct volume status
scsi: smartpqi: do not offline disks for transient did no connect conditions
scsi: smartpqi: allow for larger raid maps
...
This patch adds a "pci_bus_reset" option to the board_mode sysfs attribute.
This option uses the pci_reset_bus() api to reset the PCIe link the adapter
is on, which will reset the chip/adapter. Prior to issuing this option,
all functions on the same chip must be placed in the offline state by the
admin. After the reset, all of the instances may be brought online again.
The primary purpose of this functionality is to support cases where
firmware update required a chip reset but the admin did not want to reboot
the machine in order to instantiate the firmware update.
Sanity checks take place prior to the reset to ensure the adapter is the
sole entity on the PCIe bus and that all functions are in the offline
state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a target's link dropped, an RSCN was received to communicate the
change. The driver detected the loss of the target and issued and UNREG_RPI
mailbox command. While that was being processed, another RSCN was received
to communicate the port coming back. The driver deferred the PLOGI to the
port until the mailbox command finishes. When the mailbox command completed
it saw the pending port and called the routines to issue the
PLOGI. However, it forgot to clear the UNREG_INP state flag, so the PLOGI
xmt routine nooped the PLOGI request assuming it needed to wait for the
mailbox command. At this point, login would never be re-attempted.
Clear UNREG_INP before issuing the deferred PLOGI.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The existing MDS loopback diagnostics support processing received frames in
the slowpath work thread. It caps the number of frames it will process at
64, before waiting for another event to indicate additional frame
reception. The net-net is this results in very slow frame processing during
loopback tests and sometimes orphans an io, causing the loopback test to
report failure by the switch.
Move MDS loopback frame processing out of the slow path worker thread and
into the normal RQ processing routines.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Certain older adapters such as the OneConnect OCe10100 may not have a valid
wqpcnt value. In this case, do not set queue->page_count to 0 in
lpfc_sli4_queue_alloc() as this will prevent the driver from initializing.
Fixes: 895427bd01 ("scsi: lpfc: NVME Initiator: Base modifications")
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On driver termination, after the driver stops fw logging by writing a
register on the chip, the driver immediately unmaps and frees the logging
buffer, without confirming in any way that the chip has received the write
and terminated the logging. As termination on the chip is not immediate,
the chip may issue a dma request to the now unmapped dma buffer, resulting
in a iommu fault.
Change the driver to receive a confirmation that logging ahs been
terminated. As the driver always issues an SLI reset with the device as
part of shutdown, and as part of that is receiving confirmation that the
reset is complete - the driver was modified to perform the write to disable
fw logging prior to the SLI reset and only free the fw log buffer after the
SLI reset is complete. That guarantees use of the fw log buffer is fully
terminated when it is unmapped.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver is setting bits in word 10 of the SLI4 ABORT WQE (the wqid). The
field was a carry over from a prior SLI revision. The field does not exist
in SLI4, and the action may result in an overlap with future definition of
the WQE.
Remove the setting of WQID in the ABORT WQE.
Also cleaned up WQE field settings - initialize to zero, don't bother to
set fields to zero.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver is hitting null pring pointers in lpfc_do_work().
Pointer assignment occurs based on SLI-revision. If recovering after an
error, its possible the sli revision for the port was cleared, making the
lpfc_phba_elsring() not return a ring pointer, thus the null pointer.
Add SLI revision checking to lpfc_phba_elsring() and status checking to all
callers.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is getting hit with 100s of RSCNs during remote port address
changes. Each of those RSCN's ends up generating UNREG_RPI and REG_PRI
mailbox commands. The discovery engine within the driver doesn't wait for
the mailbox command completions. Instead it sets state flags and moves
forward. At some point, there's a massive backlog of mailbox commands which
take time for the adapter to process. Additionally, it appears there were
duplicate events from the switch so the driver generated duplicate mailbox
commands for the same remote port. During this window, failures on PLOGI
and PRLI ELS's are see as the adapter is rejecting them as they are for
remote ports that still have pending mailbox commands.
Streamline the discovery engine so that PLOGI log checks for outstanding
UNREG_RPIs and defer the processing until the commands complete. This
better synchronizes the ELS transmission vs the RPI registrations.
Filter out multiple UNREG_RPIs being queued up for the same remote port.
Beef up log messages in this area.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver data structure for managing a mailbox command contained two
context fields. Unfortunately, the context were considered "generic" to be
used at the whim of the command code. Of course, one section of code used
fields this way, while another did it that way, and eventually there were
mixups.
Refactored the structure so that the generic contexts become a node context
and a buffer context and all code standardizes on their use.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While trying to get adapter fw-log for a function whose buffsize was set to
0, kernel panic occurred.
When buffsize is 0, the kernel buffer for the log won't be allocated. When
fw log usage was enabled, it failed to check the buffer size, and log usage
was started. Eventually the driver referenced the unallocated log buffer.
Added checks of the buffer size before allowing fw logging to be enabled
and added check for valid buffer if enabling fw log.
Performed a couple other minor cleanups while fixing this:
- clarified log messages
- re-evaluated log message severity
- treat any error as an error, not only a couple codes
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since f44ac12f1d, BG enablement is tracked with the LPFC_SLI3_BG_ENABLED
bit, which is set in lpfc_get_cfgparam before lpfc_sli_config_sli_port() is
called. The bit shouldn't be cleared before checking the feature. Based on
problem analysis by David Bond.
Fixes: f44ac12f1d "scsi: lpfc: Memory allocation error during driver start-up on power8"
Tested-by: David Bond <dbond@suse.com>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Cc: stable@vger.kernel.org # 4.17.x
Cc: stable@vger.kernel.org # 4.18.x
Cc: stable@vger.kernel.org # 4.19.x
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replaced dma_alloc_coherent + memset with dma_zalloc_coherent.
Signed-off-by: Sabyasachi Gupta <sabyasachi.linux@gmail.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add trunking support to the driver. Trunking is found on more recent
asics. In general, trunking appears as a single "port" to the driver
and overall behavior doesn't differ. Link speed is reported as an
aggregate value, while link speed control is done on a per-physical
link basis with all links in the trunk symmetrical. Some commands
returning port information are updated to additionally provide
trunking information. And new ACQEs are generated to report physical
link events relative to the trunk.
This patch contains the following modifications:
- Added link speed settings of 128GB and 256GB.
- Added handling of trunk-related ACQEs, mainly logging and trapping
of physical link statuses.
- Added additional bsg interface to query trunk state by applications.
- Augment link_state sysfs attribtute to display trunk link status
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On FCoE adapters, when running link bounce test in a loop, initiator
failed to login with switch switch and required driver reload to
recover. Switch reached a point where all subsequent FLOGIs would be
LS_RJT'd. Further testing showed the condition to be related to not
performing FCF discovery between FLOGI's.
Fix by monitoring FLOGI failures and once a repeated error is seen
repeat FCF discovery.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/lpfc/lpfc_sli.c: In function 'lpfc_sli4_sp_handle_rcqe':
drivers/scsi/lpfc/lpfc_sli.c:13430:26: warning:
variable 'fc_hdr' set but not used [-Wunused-but-set-variable]
drivers/scsi/lpfc/lpfc_sli.c: In function 'lpfc_cq_create':
drivers/scsi/lpfc/lpfc_sli.c:14852:11: warning:
variable 'hw_page_size' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds the ability to read firmware logs from the adapter. The driver
registers a buffer with the adapter that is then written to by the adapter.
The adapter posts CQEs to indicate content updates in the buffer. While the
adapter is writing to the buffer in a circular fashion, an application will
poll the driver to read the next amount of log data from the buffer.
Driver log buffer size is configurable via the ras_fwlog_buffsize sysfs
attribute. Verbosity to be used by firmware when logging to host memory is
controlled through the ras_fwlog_level attribute. The ras_fwlog_func
attribute enables or disables loggy by firmware.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During attachment, the driver writes the EQ doorbell to disable potential
interrupts from an EQ. The current EQ doorbell format used for clearing the
interrupt is incorrect and uses an if_type=2 format, making the operation act
on the wrong EQ.
Correct the code to use the proper if_type=6 EQ doorbell format.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When taking the board offline while performing i/o, unsafe locking errors
occurred and irq level isn't properly managed.
In lpfc_sli_hba_down, spin_lock_irqsave(&phba->hbalock, flags) does not
disable softirqs raised from timer expiry. It is possible that a softirq is
raised from the lpfc_els_retry_delay routine and recursively requests the same
phba->hbalock spinlock causing deadlock.
Address the deadlocks by creating a new port_list lock. The softirq behavior
can then be managed a level deeper into the calling sequences.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When running an mds diagnostic that passes frames with the switch, soft
lockups are detected. The driver is in a CQE processing loop and has
sufficient amount of traffic that it never exits the ring processing routine,
thus the "lockup".
Cap the number of elements in the work processing routine to 64 elements. This
ensures that the cpu will be given up and the handler reschedule to process
additional items.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For ABORT_XRI_CN command, firmware identifies XRI to abort by IOTAG and RPI
combination. For ELS aborts, driver specifies IOTAG correctly but RPI is
not specified.
Fix by setting RPI in WQE.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A race condition between the context of devloss timeout handler and I/O
completion caused devloss timeout handler de-referencing pointer that had
been released.
Added the check in lpfc_sli_validate_fcp_iocb() on LPFC_IO_ON_TXCMPLQ to
capture the race condition of I/O completion and devloss timeout handler
attemption for aborting the I/O. Also, added check on lpfc_cmd->rdata
pointer before de-referenceing lpfc_cmd->rdata->pnode.
Also, added protection in lpfc_sli_abort_iocb() routine on driver performed
FCP I/O FLUSHING already under way before proceeding to aborting I/Os.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PBDE optimizations aren't supported in all firmware revs.
Make optimizations configurable in case there's a side effect on old
firmware.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver is incorrectly formatting a register on new hardware, using a format
for an older chip. This can result in non-deterministic behavior.
Ensure driver is not setting "workqueue index" in the WQ doorbell when
making a non-dpp doorbell write. The field must be zero when non-dpp.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The get_seconds() function suffers from a possible overflow in 2038 or
2106, as well as jitter due to settimeofday or leap second updates, and is
deprecated.
As we are interested in elapsed time only, using ktime_get_seconds() to
read the CLOCK_MONOTONIC timebase is ideal here. This also lets us remove
the hack that tries to deal with get_seconds() going slightly backwards,
which cannot happen with montonic timestamps.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MDS diagnostics fail because of frame count mismatch.
Unavailability of SGL is the trigger for this issue. If ELS SGL is not
available to process MDS frame, IOCB is put in FCP txq but not attempted to
post afterwards. So, driver stops processing incoming frames as it runs out
of IOCB. lpfc_drain_txq attempts to submit IOCBS that are queued in ELS
txq but MDS frames are posted to FCP WQ.
Attempt to submit IOCBs that are present in FCP txq when MDS loopback is
running.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix small formatting and wording nits in Broadcom copyright header
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enhance log messages for CQEs as they were not reporting certain fields.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver builds the control structures in host memory using
definitions that are based on 32-bit words. After building the structure
it is then written to the adapter.
This patch slightly optimizes LE hosts by copying the structures via
64-bit copies. This is doable as the adapter interface is LE thus there
is no byteswapping as the copy is performed.
The same optimization would be nice on BE systems, but when byteswapping
occurs, it swaps 32-bit words as well, thus trashing the control
structure. Given amount of code that is dependent upon the 32-bit word
definition, it was decided to not change things for the minor
optimization. Thus PPC 64-bit systems sticks with doing 32-bit copies.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When running loads that generated aborts, io errors where seen. Turns
out the abort requests where not placed on the proper WQ resulting in
the errors. Closer inspection inspection of this error also showed
improper spinlock api use.
Correct the WQ selection policy for the abort requests. Correct
spin_lock/spin_lock_irq/spin_lock_irqsave usage.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under large io load, the current sizing of asynchronous buffer counts
could be exceeded, indicated by a 2885 log message:
2885 Port Status Event: port status reg 0x81800000, port smphr
reg 0xc000, error 1=0x52004a01, error 2=0x0
Enlarge the async receive queue size. Allow for a configurable number
of buffers to be posted to each RQ, using the new attribute
lpfc_nvmet_mrq_post.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver fails to allocate command buffers in the routine
lpfc_new_scsi_buf_s4
There is an inconsistency between lpfc_mem_alloc(), where the
phba->lpfc_sg_dma_buf_pool is created, and lpfc_new_scsi_buf_s4(),
when we allocate a buffer from the pool and check the alignment. The
alignment should be on a page boundary, based on LPFC_SLI3_BG_ENABLED in
sli3_options, for both cases.
Fix by explicitly tracking sli4 vs sli3 and BG options. The result is that
phba->cfg_sg_dma_buf_size is now set correctly for SLI-4.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
POST_SGL_PAGES mailbox command failed with status (timeout).
wait_event_interruptible_timeout when called from mailbox wait interface,
gets interrupted, and will randomly fail. Behavior seems very specific to 1
particular server type.
Fix by changing from wait_event_interruptible_timeout to
wait_for_completion_timeout.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is very sloppy about the WQE structure passed between routines.
The base struct type is a 64byte wqe. But in many routines they typecast and
access 128byte wqes. There were a couple of cases in the past (corrected
already) where the typecasts were incorrectly done and the 64byte buffer was
accessed as a 128 byte buffer.
Clean this up by properly declaring wqe's as 128byte wqe's and removing the
typecasts. 64byte wqes are considered a subset of the 128byte wqes.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 1351e69fc6 ("scsi: lpfc: Add push-to-adapter support to sli4")
fails compilation on some 32-bit systems as writeq() is not supported on
all architectures. Additionally, it was pointed out that as writeX()
does byteswapping if necessary for pci vs the cpu endianness, the code
was broken on BE PPC.
After discussions with Arnd Bergmann, we've resolved the issue
to the following:
Instead of writeX(), use __raw_writeX() - which writes to io
space while preserving byte order. To use this, the code
was changed to use a different buffer that lpfc prepped
via sli_pcimem_bcopy() that was set to the bytestream to
be written.
On platforms with __raw_writeq support, use the routine, otherwise
use __raw_writel()
[mkp: checkpatch]
Fixes: 1351e69fc6 ("scsi: lpfc: Add push-to-adapter support to sli4")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hardware offload for NVME commands was created when the
FC-NVME standard was setting SGL Descriptor Type to SGL Data
Block Descriptor (0h) and SGL Descriptor Sub Type to Address (0h).
A late change in NVMe-over-Fabrics obsoleted these values, creating
a transport SGL descriptor type with new values to go into these
fields.
For initial hardware support, in order to be compliant to the spec,
use host-supplied cmd IU buffers instead of the adapter generated
values. Later hardware will correct this.
Add a module parameter to override this offload disablement if looking
for lowest latency. This is reasonable as nothing in FC-NVME uses
the SQE SGL values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current driver isn't taking advantage of a performance hint whereby
the initial data buffer descriptor can be placed in the WQE as well as
the SGL.
Add the logic to detect support for the feature and to use it when
supported.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code is very explicit in what it allows to be downloaded.
The driver checking prevented G7 firmware download. The driver
checking is unnecessary as the device will validate what it receives.
Revise the firmware download interface checking.
Added a little debug support in case there is still a failure.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Traditional SLI4 required the driver to clear Valid bits on
EQEs and CQEs after consuming them.
The new if_type=6 hardware will cycle the value for what is
valid on each queue itteration. The driver no longer has to
touch the valid bits. This also means all the cpu cache
dirtying and perhaps flush/refill's done by the hardware
in accessing the EQ/CQ elements is eliminated.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
New if_type=6 adapters support an additional BAR that provides
apertures to allow direct WQE to adapter push support - termed
Direct Packet Push (DPP). WQ creation differs slightly to ask for
a WQ to be DPP-ized. When submitting a WQE to a DPP WQ, it is
submitted to the host memory for the WQ normally, but is also
written by the host cpu directly to a BAR aperture. Write buffer
coalescing in hardware is (hopefully) turned on, enabling single
pci write operation support. The doorbell is thing rung to indicate
the WQE is available and was pushed to the aperture.
This patch:
- Updates the WQ Create commands for the DPP options
- Adds the bar mapping for if_type=6 DPP bar
- Adds the WQE pushing to the DDP aperture received from WQ create
- Adds a new module parameter to disable DPP operation if desired.
Default is enabled.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
New hardware supports a SLI-4 interface, but with a new if_type
variant of 6.
If_type=6 has a different PCI BAR map, separate EQ/CQ doorbells,
and some changes in doorbell formats.
Add the changes for the if_type into headers, adapter initialization
and control flows. Add new eq and cq handlers.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Up until now, all SLI-4 devices had the same doorbells at the same
bar locations. With newer hardware, there are now independent EQ and
CQ doorbells and the bar locations differ.
Prepare the code for new hardware by separating the eq/cq doorbell into
separate components. The components can be set based on if_type.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Up until now, an SLI-4 device had no variance in the way it handled
its EQs and CQs. With newer hardware, there are now differences in
doorbells and some differences in how entries are valid.
Prepare the code for new hardware by creating a sli4-based callout
table that can be set based on if_type.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated Copyright in files updated 11.4.0.7
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During SCSI error handling escalation to host reset, the SCSI io
routines were moved off the txcmplq, but the individual io's ON_CMPLQ
flag wasn't cleared. Thus, a background thread saw the io and attempted
to access it as if on the txcmplq.
Clear the flag upon removal.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When nvme target deferred receive logic waits for exchange resources,
the corresponding receive buffer is not replenished with the hardware.
This can result in a lack of asynchronous receive buffer resources in
the hardware, resulting in a "2885 Port Status Event: ... error
1=0x52004a01 ..." message.
Correct by replenishing the buffer whenenver the deferred logic kicks
in. Update corresponding debug messages and statistics as well.
[mkp: applied by hand]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I/O conditions on the nvme target may have the driver submitting to a
full hardware wq. The hardware wq is a shared resource among all nvme
controllers. When the driver hit a full wq, it failed the io posting
back to the nvme-fc transport, which then escalated it into errors.
Correct by maintaining a sideband queue within the driver that is added
to when the WQ full condition is hit, and drained from as soon as new WQ
space opens up.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Increased CQ and WQ sizes for SCSI FCP, matching those used for NVMe
development.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver controls when the hardware sends completions that communicate
consumption of elements from the WQ. This is done by setting a WQEC bit
on a WQE.
The current driver sets it on every Nth WQE posting. However, the driver
isn't clearing the bit if the WQE is reused. Thus, if the queue depth
isn't evenly divisible by N, with enough time, it can be set on every
element, creating a lot of overhead and risking CQ full conditions.
Correct by clearing the bit when not setting it on an Nth element.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is all set to handle the defer_rcv api for the nvmet_fc
transport, yet didn't properly recognize the return status when the
defer_rcv occurred. The driver treated it simply as an error and aborted
the io. Several residual issues occurred at that point.
Finish the defer_rcv support: recognize the return status when the io
request is being handled in a deferred style. This stops the rogue
aborts; Replenish the async cmd rcv buffer in the deferred receive if
needed.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Performing an LS abort results in the following message being seen:
0603 Invalid CQ subtype 6: 00000300 22000002 ffff0016 d0050000
and the associated exchange is not properly freed.
The code did not recognize the exchange type that was aborted, thus it
was not properly handled.
Correct by adding the NVME LS ELS type to the exchange types that are
recognized.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
XRI_ABORTED_CQE completions were not being handled in the fast path.
They were being queued and deferred to the lpfc worker thread for
processing. This is an artifact of the driver design prior to moving
queue processing out of the isr and into a workq element. Now that queue
processing is already in a deferred context, remove this artifact and
process them directly.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hardware queues are a fast staging area to push commands into the
adapter. The adapter should drain them extremely quickly. However,
under heavy io load, the host cpu is pushing commands faster than the
drain rate of the adapter causing the driver to resource busy commands.
Enlarge the hardware queue (wq & cq) to support a larger number of queue
entries (4x the prior size) before backpressure. Enlarging the queue
requires larger contiguous buffers (16k) per logical page for the
hardware. This changed calling sequences that were expecting 4K page
sizes that now must pass a parameter with the page sizes. It also
required use of a new version of an adapter command that can vary the
page size values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3O85
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: lpfc: Fix hard lock up NMI in els timeout handling.
scsi: mpt3sas: remove a stray KERN_INFO
scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event()
scsi: aacraid: use timespec64 instead of timeval
scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions
scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
scsi: mpt3sas: fix dma_addr_t casts
scsi: be2iscsi: Use kasprintf
scsi: storvsc: Avoid excessive host scan on controller change
scsi: lpfc: fix kzalloc-simple.cocci warnings
scsi: mpt3sas: Update mpt3sas driver version.
scsi: mpt3sas: Fix sparse warnings
scsi: mpt3sas: Fix nvme drives checking for tlr.
scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info
scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives.
scsi: mpt3sas: scan and add nvme device after controller reset
scsi: mpt3sas: Set NVMe device queue depth as 128
scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.
scsi: mpt3sas: API's to remove nvme drive from sml
scsi: mpt3sas: API 's to support NVMe drive addition to SML
...
System crashed due to a hard lockup at lpfc_els_timeout_handler+0x128.
The els ring's txcmplq list is corrupted: the last element in the list
does not point back the the head causing a loop. Issue is the els
processing path for sli4 hbas are using the hbalock instead of the
ring_lock for removing elements from the txcmplq list.
Use the adapter SLI_REV to determine which lock should be used for
removing iocbqs from the els rings txcmplq.
note: the future refactoring will address this so that we don't have
this ugly type-based lock code.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is encountering oops in lpfc_sli_calc_ring.
The driver is setting hba_wqidx for FCP based on the policy in use for
NVME. The two may not be the same. Change to set the wqidx based on the
FCP policy.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under heavy target nvme load duration, the lpfc irq handler is
encountering cpu lockup warnings.
Convert the driver to a shortened ISR handler which identifies the
interrupting condition then schedules a workq thread to process the
completion queue the interrupt was for. This moves all the real work
into the workq element.
As nvmet_fc upcalls are no longer in ISR context, don't set the feature
flags
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Need to make ktime samples more accurate
If ktime is turned on in the middle of an IO, the max calculation could
be misleading. Base sampling on the start time of the IO as opposed to
ktime_on.
Make ISR ktime timestamps be from when CQE is read instead of EQE.
Added additional sanity checks when deciding whether to accept an IO
sample or not.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver crashes when attempting to use a freed ndpl pointer.
The pci_remove_one handler runs on a separate kernel thread. The order
of the removal is starting by freeing all of the ndlps and then
disabling interrupts. In between these two events the driver can still
receive an ELS and process it. When it tries to use the ndlp pointer
will be NULL
Change the order of the pci_remove_one vs disable interrupts so that
interrupts are disabled before the ndlp's are freed.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During pci hot plug, the kernel crashes in a list_add_call
The lookup by tag function will return null if the IOCB is out of range
or does not have the on txcmplq flag set.
Fix: Check for null return from lookup by tag.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The pointer eqe is always non-null inside the while loop, so the check
to see if eqe is NULL is redudant and hence can be removed.
Detected by CoverityScan CID#1248693 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Various oops including cpu LOCKUPs were seen.
For asynchronously received ius where the driver must assign exchange
resources, the resources were on a single get (free) list and put list
(finished, waiting to be put on get list). As all cpus are sharing the
lists, an interrupt for a receive frame may have to wait for all the
other cpus to place their done work onto the put list before it can
acquire the lock to pull from the list.
Fix by breaking the resource lists into per-cpu lists or at least more
than 1 list with cpu's sharing the lists). A cpu would allocate from the
free list for its own cpu, and put its done work on the its own put list
- avoiding the contention. As cpu load may vary, when empty, a cpu may
grab from another cpu, thereby changing resource distribution. But
searching for a resource only occurs on 1 or a few cpus until a single
resource can be allocated. if the condition reoccurs, it starts looking
at a different cpu.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Various oops being seen on being in the ISR too long and cpu lockups,
when under heavy load.
The amount of work being posted off of completion queues kept the ISR
running almost all the time
Correct the issue by limiting the amount of work per iteration.
[mkp: typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify driver return error codes to align with host nvme transport.
Driver isn't returning Exxx error codes to properly reflect out of
resource or connectivity conditions (-EBUSY), yet there were hard error
conditions returning -EBUSY.
Ensure the following situations return the proper return code:
- Temporary failures or temporary resource availability: -EBUSY
- Connectivity issues: -ENODEV
All others are treated as hard errors and return an -Exxx value that
indicates the type of error.
Also, lpfc_sli4_issue_wqe() was modified to not translate error from
-Exxx to WQE state. This allows lpfc_nvme_fcp_io_submit() routine to
just return whatever -E value was returned from other routines.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API. It also updates
some comments, accordingly.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During every reset, IOCBs are allocated. So, at one point, number of
allocated IOCBs reaches maximum limit and lpfc_sli_next_iotag fails.
Allocate IOCBs only during initialization. Reuse them after every reset
instead of allocating new set of IOCBs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
OS crashes after the completion of firmware download.
Failure in posting SCSI SGL buffers because number of SGL buffers is
less than total count. Some of the pending IOs are not completed by
driver. SGL buffers for these IOs are not added back to the list.
Pending IOs are not completed because lpfc_wq_list list is initialized
before completion of pending IOs.
Postpone lpfc_wq_list reinitialization by moving
lpfc_sli4_queue_destroy() after lpfc_hba_down_post().
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a null pointer dereference that can happen in the FOF interrupt
handler.
The driver was not setting up cq->assoc_qp_for sli4_hba->oas_cq.
Initialize cq->assoc_qp before accessing it.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Administrator intervention is currently required to get good numbers
when switching from running latency tests to IOPS tests.
The configured interrupt coalescing values will greatly effect the
results of these tests. Currently, the driver has a single coalescing
value set by values of the module attribute. This patch changes the
driver to support auto-configuration of the coalescing value based on
the total number of outstanding IOs and average number of CQEs processed
per interrupt for an EQ. Values are checked every 5 seconds.
The driver defaults to the automatic selection. Automatic selection can
be disabled by the new lpfc_auto_imax module_parameter.
Older hardware can only change interrupt coalescing by mailbox
command. Newer hardware supports change via a register. The patch
support both.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addressed the following reported defects:
** CID 1411552: Control flow issues (MISSING_BREAK)
/drivers/scsi/lpfc/lpfc_sli.c: 13259 in lpfc_sli4_nvmet_handle_rcqe()
** CID 1411553: Memory - illegal accesses (OVERRUN)
/drivers/scsi/lpfc/lpfc_sli.c: 16218 in lpfc_fc_frame_check()
** CID 1411553: Memory - illegal accesses (OVERRUN)
Overrunning array "lpfc_rctl_names" of 202 8-byte elements at element
index 244 (byte offset 1952) using index "fc_hdr->fh_r_ctl" (which
evaluates to 244).
** CID 1411554: Null pointer dereferences (REVERSE_INULL)
/drivers/scsi/lpfc/lpfc_nvmet.c: 2131 in lpfc_nvmet_unsol_fcp_abort_cmp()
** CID 1411555: Memory - illegal accesses (UNINIT)
/drivers/scsi/lpfc/lpfc_nvmet.c: 180 in lpfc_nvmet_ctxbuf_post()
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kernel panic when log_verbose is set to 0xffffffff
phba->pport is dereferenced before it is initialized
Fix: Do not dereference phba->pport if it is NULL
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Null pointer dereference when BFS VM is powered off
The driver incorrectly uses sli3_ring on SLI-4 adapters
Use the correct ring structure based on sli_rev
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Tested-by: Raphael Silva <raphasil@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Observing lpfc port down after issuing hbacmd reset command
Failure in posting SGL buffers. If there is only one SGL buffer and rrq
is valid for its XRI, we are rightly returning NULL but not adding the
buffer back to the SGL list. So, number of buffers become less than
total count and repost fails during reset.
Add SGL buffer back to list before returning NULL.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added code to support Cisco MDS loopback diagnostic. The diagnostics run
various loopbacks including one which loops-back frame through the
driver.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Too many work items being processed in IRQ context take a lot of CPU
time and cause problems.
With a recent change, we get out of the ISR after hitting entry_repost
work items on a queue. However, the actual values for entry repost are
still high. EQ is 128 and CQ is 128, this could translate into
processing 128 * 128 (16384) work items under IRQ context.
Set entry_repost in the actual queue creation routine now. Limit EQ
repost to 8 and CQ repost to 64 to further limit the amount of time
spent in the IRQ.
Fix fof IRQ routines as well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Previous logic would just drop the IO.
Added logic to queue the IO to wait for an IO context resource from an
IO thats already in progress.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently IO resources are mapped 1 to 1 with RQ buffers posted
Added logic to separate RQE buffers from IO op resources
(sgl/iocbq/context). During initialization, the driver will determine
how many SGLs it will allocate for NVMET (based on what the firmware
reports) and associate a NVMET IOCBq and NVMET context structure with
each one.
Now that hdr/data buffers are immediately reposted back to the RQ, 512
RQEs for each MRQ is sufficient. Also, since NVMET data buffers are now
128 bytes, lpfc_nvmet_mrq_post is not necessary anymore as we will
always post the max (512) buffers per NVMET MRQ.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Using 2048 byte buffer and onle 128 bytes is needed.
Create nee LFPC_NVMET_DATA_BUF_SIZE define to use for NVMET RQ/MRQs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After running IOPS test for 30 second we get kernel:NMI watchdog:
Watchdog detected hard LOCKUP on cpu 0
The driver is speend too much time in its ISR.
In ISR EQ and CQ processing routines, if we hit the entry_repost numbers
of EQE/CQEs just break out of the routine as opposed to hitting the
doorbell with NOARM and continue processing.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Large block writes to the nvme target were failing because the default
number of RQs posted was insufficient.
Expand the NVMET RQs to 2048 RQEs and ensure a minimum of 512 RQEs are
posted, no matter how many MRQs are configured.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
More debug messages added for nvme statistics.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With 255 vports created a link trasition can casue a crash.
When going through discovery after a link bounce the driver is using
rpis before the cmd FCOE_POST_HDR_TEMPLATES completes. By doing that the
next rpi bumps the rpi range out of the boundary.
The fix it to increment the next_rpi only when the
FCOE_POST_HDR_TEMPLATE succeeds.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To select the appropriate shost template, the driver is issuing a
mailbox command to retrieve the wwn. Turns out the sending of the
command precedes the reset of the function. On SLI-4 adapters, this is
inconsequential as the mailbox command location is specified by dma via
the BMBX register. However, on SLI-3 adapters, the location of the
mailbox command submission area changes. When the function is first
powered on or reset, the cmd is submitted via PCI bar memory. Later the
driver changes the function config to use host memory and DMA. The
request to start a mailbox command is the same, a simple doorbell write,
regardless of submission area. So.. if there has not been a boot driver
run against the adapter, the mailbox command works as defaults are
ok. But, if the boot driver has configured the card and, and if no
platform pci function/slot reset occurs as the os starts, the mailbox
command will fail. The SLI-3 device will use the stale boot driver dma
location. This can cause PCI eeh errors.
Fix is to reset the sli-3 function before sending the mailbox command,
thus synchronizing the function/driver on mailbox location.
Note: The fix uses routines that are typically invoked later in the call
flow to reset the sli-3 device. The issue in using those routines is
that the normal (non-fix) flow does additional initialization, namely
the allocation of the pport structure. So, rather than significantly
reworking the initialization flow so that the pport is alloc'd first,
pointer checks are added to work around it. Checks are limited to the
routines invoked by a sli-3 adapter (s3 routines) as this fix/early call
is only invoked on a sli3 adapter. Nothing changes post the
fix. Subsequent initialization, and another adapter reset, still occur -
both on sli-3 and sli-4 adapters.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Fixes: 96418b5e2c ("scsi: lpfc: Fix eh_deadline setting for sli3 adapters.")
Cc: stable@vger.kernel.org # v4.11+
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver with nvme had this routine stubbed.
Right now XRI_ABORTED_CQE is not handled and the FC NVMET
Transport has a new API for the driver.
Missing code path, new NVME abort API
Update ABORT processing for NVMET
There are 3 new FC NVMET Transport API/ template routines for NVMET:
lpfc_nvmet_xmt_fcp_release
This NVMET template callback routine called to release context
associated with an IO This routine is ALWAYS called last, even
if the IO was aborted or completed in error.
lpfc_nvmet_xmt_fcp_abort
This NVMET template callback routine called to abort an exchange that
has an IO in progress
nvmet_fc_rcv_fcp_req
When the lpfc driver receives an ABTS, this NVME FC transport layer
callback routine is called. For this case there are 2 paths thru the
driver: the driver either has an outstanding exchange / context for the
XRI to be aborted or not. If not, a BA_RJT is issued otherwise a BA_ACC
NVMET Driver abort paths:
There are 2 paths for aborting an IO. The first one is we receive an IO and
decide not to process it because of lack of resources. An unsolicated ABTS
is immediately sent back to the initiator as a response.
lpfc_nvmet_unsol_fcp_buffer
lpfc_nvmet_unsol_issue_abort (XMIT_SEQUENCE_WQE)
The second one is we sent the IO up to the NVMET transport layer to
process, and for some reason the NVME Transport layer decided to abort the
IO before it completes all its phases. For this case there are 2 paths
thru the driver:
the driver either has an outstanding TSEND/TRECEIVE/TRSP WQE or no
outstanding WQEs are present for the exchange / context.
lpfc_nvmet_xmt_fcp_abort
if (LPFC_NVMET_IO_INP)
lpfc_nvmet_sol_fcp_issue_abort (ABORT_WQE)
lpfc_nvmet_sol_fcp_abort_cmp
else
lpfc_nvmet_unsol_fcp_issue_abort
lpfc_nvmet_unsol_issue_abort (XMIT_SEQUENCE_WQE)
lpfc_nvmet_unsol_fcp_abort_cmp
Context flags:
LPFC_NVMET_IOP - his flag signifies an IO is in progress on the exchange.
LPFC_NVMET_XBUSY - this flag indicates the IO completed but the firmware
is still busy with the corresponding exchange. The exchange should not be
reused until after a XRI_ABORTED_CQE is received for that exchange.
LPFC_NVMET_ABORT_OP - this flag signifies an ABORT_WQE was issued on the
exchange.
LPFC_NVMET_CTX_RLS - this flag signifies a context free was requested,
but we are deferring it due to an XBUSY or ABORT in progress.
A ctxlock is added to the context structure that is used whenever these
flags are set/read within the context of an IO.
The LPFC_NVMET_CTX_RLS flag is only set in the defer_relase routine when
the transport has resolved all IO associated with the buffer. The flag is
cleared when the CTX is associated with a new IO.
An exchange can has both an LPFC_NVMET_XBUSY and a LPFC_NVMET_ABORT_OP
condition active simultaneously. Both conditions must complete before the
exchange is freed.
When the abort callback (lpfc_nvmet_xmt_fcp_abort) is envoked:
If there is an outstanding IO, the driver will issue an ABORT_WQE. This
should result in 3 completions for the exchange:
1) IO cmpl with XB bit set
2) Abort WQE cmpl
3) XRI_ABORTED_CQE cmpl
For this scenerio, after completion #1, the NVMET Transport IO rsp
callback is called. After completion #2, no action is taken with respect
to the exchange / context. After completion #3, the exchange context is
free for re-use on another IO.
If there is no outstanding activity on the exchange, the driver will send a
ABTS to the Initiator. Upon completion of this WQE, the exchange / context
is freed for re-use on another IO.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
When RPI is not available, driver sends WQE with invalid RPI value and
rejected by HBA.
lpfc 0000:82:00.3: 1:3154 BLS ABORT RSP failed, data: x3/xa0320008
and
lpfc :2753 PLOGI failure DID:FFFFFA Status:x3/xa0240008
In this case, driver accesses rpi_ids array out of bounds.
Fix:
Check return value of lpfc_sli4_alloc_rpi(). Do not allocate
lpfc_nodelist entry if RPI is not available.
When RPI is not available, we will get discovery timeouts and
command drops for some of the vports as seen below.
lpfc :0273 Unexpected discovery timeout, vport State x0
lpfc :0230 Unexpected timeout, hba link state x5
lpfc :0111 Dropping received ELS cmd Data: x0 xc90c55 x0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
There are two versions of a structure for queue creation and setup that the
driver shares with FW. The driver was only treating as version 0.
Verify WQ_CREATE with 128B WQEs in V0 and V1.
Code review of another bug showed the driver passing
128B WQEs and 8 pages in WQ CREATE and V0.
Code inspection/instrumentation showed that the driver
uses V0 in WQ_CREATE and if the caller passes queue->entry_size
128B, the driver sets the hdr_version to V1 so all is good.
When I tested the V1 WQ_CREATE, the mailbox failed causing
the driver to unload.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
James Smart