When reaching the end of stream, V4L2 m2m clients may expect the
V4L2_EOS_EVENT. Although the V4L2_EOS_EVENT is deprecated behavior,
drivers must signal that event before dequeuing the buffer that has the
V4L2_BUF_FLAG_LAST flag set.
If a driver queues the V4L2_EOS_EVENT event and returns the buffer after
the check for events but before the check for buffers, vb2_m2m_poll()
will signal that the buffer with V4L2_BUF_FLAG_LAST can be read but not
that the V4L2_EOS_EVENT is available.
Split the check for buffers into a separate function and check for
available buffers before checking for events. This ensures that if
vb2_m2m_poll() signals POLLIN | POLLRDNORM for the V4L2_BUF_FLAG_LAST
buffer, it signals POLLPRI for the V4L2_EOS_EVENT, too.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix checkpatch alignment warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlz8fAYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1asH/3ySguxqtqL1MCBa
4/SZ37PHeWKMerfX6ZyJdgEqK3B+PWlmuLiOMNK5h2bPLzeQQQAmHU/mfKmpXqgB
dHwUbG9yNnyUtTfsfRqAnCA6vpuw9Yb1oIzTCVQrgJLSWD0j7scBBvmzYqguOkto
ThwigLUq3AILr8EfR4rh+GM+5Dn9OTEFAxwil9fPHQo7QoczwZxpURhScT6Co9TB
DqLA3fvXbBvLs/CZy/S5vKM9hKzC+p39ApFTURvFPrelUVnythAM0dPDJg3pIn5u
g+/+gDxDFa+7ANxvxO2ng1sJPDqJMeY/xmjJYlYyLpA33B7zLNk2vDHhAP06VTtr
XCMhQ9s=
=cb80
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc4' into media/master
There are some conflicts due to SPDX changes. We also have more
patches being merged via media tree touching them.
So, let's merge back from upstream and address those.
Linux 5.2-rc4
* tag 'v5.2-rc4': (767 commits)
Linux 5.2-rc4
MAINTAINERS: Karthikeyan Ramasubramanian is MIA
i2c: xiic: Add max_read_len quirk
lockref: Limit number of cmpxchg loop retries
uaccess: add noop untagged_addr definition
x86/insn-eval: Fix use-after-free access to LDT entry
kbuild: use more portable 'command -v' for cc-cross-prefix
s390/unwind: correct stack switching during unwind
block, bfq: add weight symlink to the bfq.weight cgroup parameter
cgroup: let a symlink too be created with a cftype file
drm/nouveau/secboot/gp10[2467]: support newer FW to fix SEC2 failures on some boards
drm/nouveau/secboot: enable loading of versioned LS PMU/SEC2 ACR msgqueue FW
drm/nouveau/secboot: split out FW version-specific LS function pointers
drm/nouveau/secboot: pass max supported FW version to LS load funcs
drm/nouveau/core: support versioned firmware loading
drm/nouveau/core: pass subdev into nvkm_firmware_get, rather than device
block: free sched's request pool in blk_cleanup_queue
pktgen: do not sleep with the thread lock held.
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
...
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Most if not all codecs will need to implement these ioctls and
it is expected to be the same for all codecs. So add this to
the core v4l2-mem2mem framework so that this code can easily be
reused.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit changes the return type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
which currently return void pointer.
In every case, the actual return type is a struct vb2_v4l2_buffer
pointer. Change the return type of the listed functions,
so type checking can be properly used.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: clean up line-too-long checkpatch warnings]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The v4l2_m2m_poll function didn't check whether q->error
was set for either of the two queues. Add support for this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The epoll function expects that whenever the poll file op is
called, the poll_wait function is also called. That didn't
always happen in v4l2_m2m_poll(). Fix this, otherwise
epoll() would timeout when it shouldn't.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If a stream is stopped, or if a USERPTR/DMABUF buffer is queued
backed by a different user address or dmabuf fd, then the timestamp
should be skipped by vb2_find_timestamp since the memory it refers
to is no longer valid.
So keep track of a 'copied_timestamp' state: it is set when the
timestamp is copied from an output to a capture buffer, and is
cleared when it is no longer valid.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The v4l2_m2m_buf_copy_data helper is used to copy the buffer
metadata, such as its timestamp and its flags.
Therefore, the v4l2_m2m_buf_copy_metadata name is more clear
and avoids confusion with a payload data copy.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: also fix cedrus_dec.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Memory-to-memory devices should copy various parts of
struct v4l2_buffer from the output buffer to the capture buffer.
Add a helper function that does that to simplify the driver code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_m2m_job_finish() is typically called when
DMA operations complete, in interrupt handlers or DMA
completion callbacks. Calling .device_run from v4l2_m2m_job_finish
creates a nasty re-entrancy path into the driver.
Moreover, some implementation of .device_run might need to sleep,
as is the case for drivers supporting the Request API,
where controls are applied via v4l2_ctrl_request_setup,
which takes the ctrl handler mutex.
This commit adds a deferred context that calls v4l2_m2m_try_run,
and gets scheduled by v4l2_m2m_job_finish().
Before this change, device_run would be called from these
paths:
vb2_m2m_request_queue, or
v4l2_m2m_streamon, or
v4l2_m2m_qbuf
v4l2_m2m_try_schedule
v4l2_m2m_try_run
.device_run
v4l2_m2m_job_finish
v4l2_m2m_try_run
.device_run
After this change, the latter is now gone and instead:
v4l2_m2m_device_run_work
v4l2_m2m_try_run
.device_run
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The __v4l2_m2m_try_schedule function acquires and releases multiple
spinlocks. Simplify unlocking the job lock by adding labels to unlock
the lock and exit the function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, all the mem2mem driver either use a single mutex
to lock the capture and output videobuf2 queues, or don't
set any mutex.
This means the mutexes match, and so the mem2mem framework
is able to set the m2m context lock.
Enforce this by making it mandatory for drivers to set
the same capture and output mutex, or not set any mutex at all.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To be consistent with the rest of the mem2mem helpers,
rename vb2_m2m_request_queue to v4l2_m2m_request_queue.
This is just a cosmetic change.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
For mem2mem devices we have to make sure that v4l2_m2m_try_schedule()
is called whenever a request is queued.
We do that by creating a vb2_m2m_request_queue() helper that should
be used instead of the 'normal' vb2_request_queue() helper. The m2m
helper function will call v4l2_m2m_try_schedule() as needed.
In addition we also avoid calling v4l2_m2m_try_schedule() when preparing
or queueing a buffer for a request since that is no longer needed.
Instead this helper function will do that when the request is actually
queued.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This implements the V4L2 part of the request support. The main
change is that vb2_qbuf and vb2_prepare_buf now have a new
media_device pointer. This required changes to several drivers
that did not use the vb2_ioctl_qbuf/prepare_buf helper functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
drivers/media/v4l2-core/v4l2-mem2mem.c:90: warning: Function parameter or member 'source_pad' not described in 'v4l2_m2m_dev'
drivers/media/v4l2-core/v4l2-mem2mem.c:90: warning: Function parameter or member 'sink' not described in 'v4l2_m2m_dev'
drivers/media/v4l2-core/v4l2-mem2mem.c:90: warning: Function parameter or member 'sink_pad' not described in 'v4l2_m2m_dev'
drivers/media/v4l2-core/v4l2-mem2mem.c:90: warning: Function parameter or member 'proc' not described in 'v4l2_m2m_dev'
drivers/media/v4l2-core/v4l2-mem2mem.c:90: warning: Function parameter or member 'proc_pads' not described in 'v4l2_m2m_dev'
drivers/media/v4l2-core/v4l2-mem2mem.c:90: warning: Function parameter or member 'intf_devnode' not described in 'v4l2_m2m_dev'
Fixes: be2fff6563 ("media: add helpers for memory-to-memory media controller")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 34dbb848d5 ("media: mem2mem: Remove excessive try_run call")
removed a redundant call to v4l2_m2m_try_run but instead introduced
a bug. Consider the following case:
1) Context A schedules, queues and runs job A.
2) While the m2m device is running, context B schedules
and queues job B. Job B cannot run, because it has to
wait for job A.
3) Job A completes, calls v4l2_m2m_job_finish, and tries
to queue a job for context A, but since the context is
empty it won't do anything.
In this scenario, queued job B will never run. Fix this by calling
v4l2_m2m_try_run from v4l2_m2m_try_schedule.
While here, add more documentation to these functions.
Fixes: 34dbb848d5 ("media: mem2mem: Remove excessive try_run call")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: split >80 cols line]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This can be used to mark the last queued source buffer as the last
buffer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Implementing job_abort() does not make sense on some drivers.
This is not a problem, as the abort is not required to
wait for the job to finish. Quite the opposite, drivers
are encouraged not to wait.
Demote v4l2_m2m_ops.job_abort from required to optional, and
clean all drivers with dummy implementations.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A memory-to-memory pipeline device consists in three
entities: two DMA engine and one video processing entities.
The DMA engine entities are linked to a V4L interface.
This commit add a new v4l2_m2m_{un}register_media_controller
API to register this topology.
For instance, a typical mem2mem device topology would
look like this:
Device topology
- entity 1: source (1 pad, 1 link)
type Node subtype V4L flags 0
pad0: Source
-> "proc":1 [ENABLED,IMMUTABLE]
- entity 3: proc (2 pads, 2 links)
type Node subtype Unknown flags 0
pad0: Source
-> "sink":0 [ENABLED,IMMUTABLE]
pad1: Sink
<- "source":0 [ENABLED,IMMUTABLE]
- entity 6: sink (1 pad, 1 link)
type Node subtype V4L flags 0
pad0: Sink
<- "proc":0 [ENABLED,IMMUTABLE]
[hans.verkuil@cisco.com: mark interface links as IMMUTABLE]
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If there is a schedulable job, v4l2_m2m_try_schedule() calls
v4l2_m2m_try_run(). This makes the unconditional v4l2_m2m_try_run()
called by v4l2_m2m_job_finish superfluous. Remove it.
Fixes: 7f98639def ("V4L/DVB: add memory-to-memory device helper framework for videobuf")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
There are some troubles on kernel-doc markups, as warned:
drivers/media/v4l2-core/v4l2-dv-timings.c:259: warning: No description found for parameter 't1'
drivers/media/v4l2-core/v4l2-dv-timings.c:259: warning: No description found for parameter 't2'
drivers/media/v4l2-core/v4l2-dv-timings.c:259: warning: No description found for parameter 'pclock_delta'
drivers/media/v4l2-core/v4l2-dv-timings.c:259: warning: No description found for parameter 'match_reduced_fps'
drivers/media/v4l2-core/tuner-core.c:242: warning: bad line: internal parameters, like LNA mode
drivers/media/v4l2-core/tuner-core.c:765: warning: No description found for parameter 'mode'
drivers/media/v4l2-core/videobuf2-memops.c:127: warning: cannot understand function prototype: 'const struct vm_operations_struct vb2_common_vm_ops = '
drivers/media/v4l2-core/v4l2-mem2mem.c:190: warning: No description found for parameter 'm2m_dev'
drivers/media/v4l2-core/v4l2-mem2mem.c:291: warning: No description found for parameter 'm2m_ctx'
drivers/media/v4l2-core/videobuf-core.c:233: warning: No description found for parameter 'q'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
this add functions for:
- remove buffers from src/dst queue by index
- remove exact buffer from src/dst queue
also extends m2m API to iterate over a list of src/dst buffers
in safely and non-safely manner.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several routines are somewhat documented at v4l2-mem2mem.c
file. Move what's there to the header file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove v4l2 stuff - v4l2_buf, v4l2_plane - from struct vb2_buffer.
Add new member variables - bytesused, length, offset, userptr, fd,
data_offset - to struct vb2_plane in order to cover all information
of v4l2_plane.
struct vb2_plane {
<snip>
unsigned int bytesused;
unsigned int length;
union {
unsigned int offset;
unsigned long userptr;
int fd;
} m;
unsigned int data_offset;
}
Replace v4l2_buf with new member variables - index, type, memory - which
are common fields for buffer management.
struct vb2_buffer {
<snip>
unsigned int index;
unsigned int type;
unsigned int memory;
unsigned int num_planes;
struct vb2_plane planes[VIDEO_MAX_PLANES];
<snip>
};
v4l2 specific fields - flags, field, timestamp, timecode,
sequence - are moved to vb2_v4l2_buffer in videobuf2-v4l2.c
struct vb2_v4l2_buffer {
struct vb2_buffer vb2_buf;
__u32 flags;
__u32 field;
struct timeval timestamp;
struct v4l2_timecode timecode;
__u32 sequence;
};
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make videobuf2-v4l2 as a wrapper of videobuf2-core for v4l2-use.
And replace videobuf2-core.h with videobuf2-v4l2.h.
This renaming change should be accompanied by the modifications
of all device drivers that include videobuf2-core.h.
It can be done with just running this shell script.
replace()
{
str1=$1
str2=$2
dir=$3
for file in $(find $dir -name *.h -o -name *.c -o -name Makefile)
do
echo $file
sed "s/$str1/$str2/g" $file > $file.out
mv $file.out $file
done
}
replace "videobuf2-core" "videobuf2-v4l2" "include/media/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/media/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/usb/gadget/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/staging/media/"
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The queue owner will be used by videobuf2 trace events to determine and
record the device minor number. It is set in v4l2_m2m_reqbufs instead of
v4l2_m2m_ioctl_reqbufs because several drivers implement their own
vidioc_reqbufs handlers that still call v4l2_m2m_reqbufs directly.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This was never added for some reason, so add it now.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the last buffer was dequeued from a capture queue, let poll return
immediately and let DQBUF return -EPIPE to signal there will no more
buffers to dequeue until STREAMOFF.
The driver signals the last buffer by setting the V4L2_BUF_FLAG_LAST.
To reenable dequeuing on the capture queue, the driver must explicitly
call vb2_clear_last_buffer_queued. The last buffer queued flag is
cleared automatically during STREAMOFF.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The first time b is used, it is assigned to the first element of the rdy_queue
list. There is no need to set it to NULL before.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some drivers might allow to decode remaining frames from an internal ringbuffer
after a decoder stop command. Allow those to call v4l2_m2m_try_schedule
directly.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch makes the queue lock taken in v4l2_m2m_poll interruptible.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds ioctl helpers to the V4L2 mem-to-mem API, so we can avoid
several ioctl handlers in the mem-to-mem video node drivers that are simply
a pass-through to the v4l2_m2m_* calls. These helpers will only be useful
for drivers that use same mutex for both OUTPUT and CAPTURE queue, which
is the case for all currently in tree v4l2 m2m drivers. In order to use
the helpers the drivers are required to use struct v4l2_fh.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the current context is running,
1] If release is called, it waits until the job is finished.
2] As soon as the job is finished, v4l2_mem_ctx_release()tries to
release the vb2 queues.
3] But if the current context can be scheduled in the v4l2_m2m_job_finish()
it schedules the context and tries to call device_run().
4] As the release() and device_run() sequence can't be predicted sometimes
device_run() may get empty vb2 buffers.
This patch adds the ABORT state to the job_flags. Once the job_abort() or
release() is called on the context, the same context will not be scheduled in
the v4l2_m2m_job_finish().
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
v4l2_m2m_streamoff drops the list of ready buffers but failed to reset the
num_rdy counter to zero. This would lead to v4l2_m2m_num_src/dst_bufs_ready
reporting wrong values after streamoff.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just clearing the m2m_ctx->queue list_head will leave the m2m_dev->job_queue
in a broken state and can cause scheduling of device_runs after streamoff was
called.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When streamoff is called on the context and the context
is added to the job_queue,
1] sometimes device_run receives the empty vb2 buffers (as
v4l2_m2m_streamoff is dropping the ready queue).
2] sometimes v4l2_m2m_job_finish may not succeed as the m2m_dev->curr_ctx
is made NULL in the v4l2_m2m_streamoff()
The above points may stop the execution of the other queued contexts.
This patch makes sure that before streamoff is executed on any context,
that context should "not be running" or "not queued" in the job_queue.
1] If the current context is running, then abort job will be called.
2] If the current context is queued, then the context will be removed from
the job_queue.
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On mem2mem decoders with a hardware bitstream ringbuffer, to drain the
buffer at the end of the stream, remaining frames might need to be decoded
from the bitstream buffer without additional input buffers being provided.
To achieve this, allow a queue to be marked as buffered by the driver, and
allow scheduling of device_runs when buffered ready queues are empty.
This also allows a driver to copy input buffers into their bitstream
ringbuffer and immediately mark them as done to be dequeued.
The motivation for this patch is hardware assisted h.264 reordering support
in the coda driver. For high profile streams, the coda can hold back
out-of-order frames, causing a few mem2mem device runs in the beginning, that
don't produce any decompressed buffer at the v4l2 capture side. At the same
time, the last few frames can be decoded from the bitstream with mem2mem device
runs that don't need a new input buffer at the v4l2 output side. The decoder
command ioctl can be used to put the decoder into the ringbuffer draining
end-of-stream mode.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The v4l2_m2m_poll() does not need to wait if there is already a buffer in
done_list of source and destination queues, but current v4l2_m2m_poll() always
waits. So done_list of each queue is checked before calling poll_wait().
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When a v4l2-mem2mem context gets a STREAMOFF call on either its CAPTURE
or OUTPUT queues, we should:
* Drop the corresponding rdy_queue, since a subsequent STREAMON expects
an empty queue.
* Deschedule the context, as it now has at least one empty queue and
cannot run.
Signed-off-by: John Sheu <sheu@google.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In v4l2_m2m_try_schedule(), use the CAPTURE queue lock when accessing
the CAPTURE queue, instead of relying on just holding the OUTPUT queue
lock.
Signed-off-by: John Sheu <sheu@google.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Tretter