- Backwards Compatibility:
If userspace wants to determine whether ipv4 RTM_GETADDR requests
support the new IFA_TARGET_NETNSID property it should verify that the
reply includes the IFA_TARGET_NETNSID property. If it does not
userspace should assume that IFA_TARGET_NETNSID is not supported for
ipv4 RTM_GETADDR requests on this kernel.
- From what I gather from current userspace tools that make use of
RTM_GETADDR requests some of them pass down struct ifinfomsg when they
should actually pass down struct ifaddrmsg. To not break existing
tools that pass down the wrong struct we will do the same as for
RTM_GETLINK | NLM_F_DUMP requests and not error out when the
nlmsg_parse() fails.
- Security:
Callers must have CAP_NET_ADMIN in the owning user namespace of the
target network namespace.
Signed-off-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a new IFA_TARGET_NETNSID property to be used by address
families such as PF_INET and PF_INET6.
The IFA_TARGET_NETNSID property can be used to send a network namespace
identifier as part of a request. If a IFA_TARGET_NETNSID property is
identified it will be used to retrieve the target network namespace in
which the request is to be made.
Signed-off-by: Christian Brauner <christian@brauner.io>
Cc: Jiri Benc <jbenc@redhat.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
get_target_net() will be used in follow-up patches in ipv{4,6} codepaths to
retrieve network namespaces based on network namespace identifiers. So
remove the static declaration and export in the rtnetlink header. Also,
rename it to rtnl_get_net_ns_capable() to make it obvious what this
function is doing.
Export rtnl_get_net_ns_capable() so it can be used when ipv6 is built as
a module.
Signed-off-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Wahren says:
====================
net: lan78xx: Minor improvements
This patch series contains some minor improvements for the lan78xx
driver.
Changes in V2:
- Keep Copyright comment as multi-line
- Add Raghuram's Reviewed-by
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes some declaration more consistent.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Raghuram Chary Jallipalli <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for this strcpy because alloc_etherdev() already
does this job.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Raghuram Chary Jallipalli <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to bail out if lan78xx_get_endpoints() fails, otherwise the
result is overwritten.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Raghuram Chary Jallipalli <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VXLAN and GRE FW features have to currently be both advertised
for the driver to enable them. Separate the handling.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
nfp: improve the new rtsym helpers
This set fixes a bug in ABS rtsym handling I added in net-next,
it expands the error checking and reporting on the rtsym accesses.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With the accesses to rtsyms now all going via special helpers
we can easily make sure the driver is not reading past the
end of the symbol.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ease of debug preface all error messages with the name
of the symbol which caused them. Use the same message format
for existing messages while at it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return the error and report value through the output param.
Fixes: 640917dd81 ("nfp: support access to absolute RTsyms")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/net_failover.c: In function 'net_failover_slave_unregister':
drivers/net/net_failover.c:598:35: warning:
variable 'primary_dev' set but not used [-Wunused-but-set-variable]
There should check the validity of 'slave_dev'.
Fixes: cfc80d9a11 ("net: Introduce net_failover driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Linus noted, the test for 0 is needless, groups type can follow the
usual kernel style and 8*sizeof(unsigned long) is BITS_PER_LONG:
> The code [..] isn't technically incorrect...
> But it is stupid.
> Why stupid? Because the test for 0 is pointless.
>
> Just doing
> if (nlk->ngroups < 8*sizeof(groups))
> groups &= (1UL << nlk->ngroups) - 1;
>
> would have been fine and more understandable, since the "mask by shift
> count" already does the right thing for a ngroups value of 0. Now that
> test for zero makes me go "what's special about zero?". It turns out
> that the answer to that is "nothing".
[..]
> The type of "groups" is kind of silly too.
>
> Yeah, "long unsigned int" isn't _technically_ wrong. But we normally
> call that type "unsigned long".
Cleanup my piece of pointlessness.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: netdev@vger.kernel.org
Fairly-blamed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the only way to ignore outgoing packets on a packet socket is
via the BPF filter. With MSG_ZEROCOPY, packets that are looped into
AF_PACKET are copied in dev_queue_xmit_nit(), and this copy happens even
if the filter run from packet_rcv() would reject them. So the presence
of a packet socket on the interface takes away the benefits of
MSG_ZEROCOPY, even if the packet socket is not interested in outgoing
packets. (Even when MSG_ZEROCOPY is not used, the skb is unnecessarily
cloned, but the cost for that is much lower.)
Add a socket option to allow AF_PACKET sockets to ignore outgoing
packets to solve this. Note that the *BSDs already have something
similar: BIOCSSEESENT/BIOCSDIRECTION and BIOCSDIRFILT.
The first intended user is lldpd.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/microchip/lan743x_ptp.c:980:6: warning:
symbol 'lan743x_ptp_set_sync_ts_insert' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/ipoib/ipoib.c:119:6: warning:
symbol 'mlx5i_grp_sw_update_stats' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the changes:
* changes to make PTK rekeying work better, or actually
better/safely if drivers get updated
* VHT extended NSS support - some APs had capabilities
that didn't fit into the VHT (11ac) spec, so the spec
was updated and we follow that now
* some TXQ and A-MSDU building work - will allow iwlwifi
to use this soon
* more HE work, including aligning to 802.11ax Draft 3.0
* L-SIG and 0-length-PSDU support in radiotap
-----BEGIN PGP SIGNATURE-----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=HYA6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-09-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time, we have some pretty impactful work. Among
the changes:
* changes to make PTK rekeying work better, or actually
better/safely if drivers get updated
* VHT extended NSS support - some APs had capabilities
that didn't fit into the VHT (11ac) spec, so the spec
was updated and we follow that now
* some TXQ and A-MSDU building work - will allow iwlwifi
to use this soon
* more HE work, including aligning to 802.11ax Draft 3.0
* L-SIG and 0-length-PSDU support in radiotap
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add validation check for wmm rule when copy rules from fwdb and print
error when rule is invalid.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Both old and new cannot be NULL at the same time, hence checking
new when old is not NULL is unnecessary.
Also, notice that new is being dereferenced before it is checked:
idx = new->conf.keyidx;
The above triggers a static code analysis warning.
Address this by removing the NULL check on new and adding a code
comment based on the following piece of code:
387 /* caller must provide at least one old/new */
388 if (WARN_ON(!new && !old))
389 return 0;
Addresses-Coverity-ID: 1473176 ("Dereference before null check")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some hardwares have limitations on the packets' type in AMSDU.
Add an optional driver callback to determine if two skbs can
be used in the same AMSDU or not.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may have AMSDU size limitation per TID, due to
HW constrains. Add an option to set this limit.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a TXQ abstraction for non-data packets that need
powersave buffering. Since the AP cannot sleep, in case
of station we can use this TXQ for all management frames,
regardless if they are bufferable. Add HW flag to allow
that.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Align to new 11ax draft D3.0. Change/add new MAC and PHY capabilities
and update drivers' 11ax capabilities and mac80211's debugfs
accordingly.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After masking the he_oper_params, to get the requested values as
integers one must rshift and not lshift. Fix that by using the
le32_get_bits() macro.
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
[converted to use le32_get_bits()]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For certain sounding frames, it may be useful to report them
to userspace even though they don't have a PSDU in order to
determine the PHY parameters (e.g. VHT rate/stream config.)
Add support for this to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rekeying PTK keys without "Extended Key ID for Individually Addressed
Frames" did use a procedure not suitable to replace in-use keys and
could caused the following issues:
1) Freeze caused by incoming frames:
If the local STA installed the key prior to the remote STA we still
had the old key active in the hardware when mac80211 switched over
to the new key.
Therefore there was a window where the card could hand over frames
decoded with the old key to mac80211 and bump the new PN (IV) value
to an incorrect high number. When it happened the local replay
detection silently started to drop all frames sent with the new key.
2) Freeze caused by outgoing frames:
If mac80211 was providing the PN (IV) and handed over a clear text
frame for encryption to the hardware prior to a key change the
driver/card could have processed the queued frame after switching
to the new key. This bumped the PN value on the remote STA to an
incorrect high number, tricking the remote STA to discard all frames
we sent later.
3) Freeze caused by RX aggregation reorder buffer:
An aggregation session started with the old key and ending after the
switch to the new key also bumped the PN to an incorrect high number,
freezing the connection quite similar to 1).
4) Freeze caused by repeating lost frames in an aggregation session:
A driver could repeat a lost frame and encrypt it with the new key
while in a TX aggregation session without updating the PN for the
new key. This also could freeze connections similar to 2).
5) Clear text leak:
Removing encryption offload from the card cleared the encryption
offload flag only after the card had deleted the key and we did not
stop TX during the rekey. The driver/card could therefore get
unencrypted frames from mac80211 while no longer be instructed to
encrypt them.
To prevent those issues the key install logic has been changed:
- Mac80211 divers known to be able to rekey PTK0 keys have to set
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0,
- mac80211 stops queuing frames depending on the key during the replace
- the key is first replaced in the hardware and after that in mac80211
- and mac80211 stops/blocks new aggregation sessions during the rekey.
For drivers not setting
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 the user space must avoid PTK
rekeys if "Extended Key ID for Individually Addressed Frames" is not
being used. Rekeys for mac80211 drivers without this flag will generate a
warning and use an extra call to ieee80211_flush_queues() to both
highlight and try to prevent the issues with not updated drivers.
The core of the fix changes the key install procedure from:
- atomic switch over to the new key in mac80211
- remove the old key in the hardware (stops encryption offloading, fall
back to software encryption with a potential clear text packet leak
in between)
- delete the inactive old key in mac80211
- enable hardware encryption offloading for the new key
to:
- if it's a PTK mark the old key as tainted to drop TX frames with the
outgoing key
- replace the key in hardware with the new one
- atomic switch over to the new (not marked as tainted) key in
mac80211 (which also resumes TX)
- delete the inactive old key in mac80211
With the new sequence the hardware will be unable to decrypt frames
encrypted with the old key prior to switching to the new key in mac80211
and thus prevent PNs from packets decrypted with the old key to be
accounted against the new key.
For that to work the drivers have to provide a clear boundary.
Mac80211 drivers setting @NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 confirm
to provide it and mac80211 will then be able to correctly rekey in-use
PTK keys with those drivers.
The mac80211 requirements for drivers to set the flag have been added to
the "Hardware crypto acceleration" documentation section. It drills down
to:
The drivers must not hand over frames decrypted with the old key to
mac80211 once the call to set_key() with %DISABLE_KEY has been
completed. It's allowed to either drop or continue to use the old key
for any outgoing frames which are already in the queues, but it must not
send out any of them unencrypted or encrypted with the new key.
Even with the new boundary in place aggregation sessions with the
reorder buffer are problematic:
RX aggregation session started prior and completed after the rekey could
still dump frames received with the old key at mac80211 after it
switched over to the new key. This is side stepped by stopping all (RX
and TX) aggregation sessions when replacing a PTK key and hardware key
offloading.
Stopping TX aggregation sessions avoids the need to get
the PNs (IVs) updated in frames prepared for the old key and
(re)transmitted after the switch to the new key. As a bonus it improves
the compatibility when the remote STA is not handling rekeys as it
should.
When using software crypto aggregation sessions are not stopped.
Mac80211 won't be able to decode the dangerous frames and discard them
without special handling.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[trim overly long rekey warning]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers able to correctly replace a in-use key should set
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to allow the user space (e.g.
hostapd or wpa_supplicant) to rekey PTK keys.
The user space must detect a PTK rekey attempt and only go ahead with it
when the driver has set this flag. If the driver is not supporting the
feature the user space either must not replace the PTK key or perform a
full re-association instead.
Ignoring this flag and continuing to rekey the connection can still work
but has to be considered insecure and broken. Depending on the driver it
can leak clear text packets or freeze the connection and is only
supported to allow the user space to be updated.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Reviewed-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As before with HE, the data needs to be provided by the
driver in the skb head, since there's not enough space
in the skb CB.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make it possibly for drivers to adjust the default skb_pacing_shift
by storing it in the hardware struct.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
[adjust commit log, move & adjust comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When taking VHT capabilities for a station, copy the new
fields if we support them as a transmitter. Also adjust
the maximum bandwidth the station supports appropriately.
Also, since it was missing, copy tx_highest and rx_highest.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With newer VHT implementations, it's necessary to look at the
HT operation's CCFS2 field to identify the actual bandwidth
used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on whether or not rate control supports selecting
rates depending on the bandwidth, we can use VHT extended
NSS support. In essence, this is dot11VHTExtendedNSSBWCapable
from the spec, since depending on that we'll need to parse
the bandwidth.
If needed, also set/clear the VHT Capability Element bit for
this capability so that we don't advertise it erroneously or
don't advertise it when we actually use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE 802.11-2016 extended the VHT capability fields to allow
indicating the number of spatial streams depending on the
actually used bandwidth, add support for decoding this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP mode, If AP advertises HE capabilities, set to true
bss_conf::he_supported so that the Driver knows about it.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Same as for HT and VHT.
This helps the lower level to know whether the AP supports HE.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The defines of IEEE80211_HE_OPERATION_VHT_OPER_INFO and
IEEE80211_HE_OPERATION_MULTI_BSSID_AP have leading zeroes
that makes the number look like it is bigger than 32 bit.
This is misleading, remove it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may want to also use the TXQ abstraction with
non-data packets that need powersave buffering, so add a
hardware flag to allow this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These checks aren't necessary, cfg80211 never passes NULL.
Some static checkers complain about the missing checks on
the next line, but really the NULL checks are unnecessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Export HE capabilities information via debugfs, similar to HT & VHT.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
1) Must perform TXQ teardown before unregistering interfaces in
mac80211, from Toke Høiland-Jørgensen.
2) Don't allow creating mac80211_hwsim with less than one channel, from
Johannes Berg.
3) Division by zero in cfg80211, fix from Johannes Berg.
4) Fix endian issue in tipc, from Haiqing Bai.
5) BPF sockmap use-after-free fixes from Daniel Borkmann.
6) Spectre-v1 in mac80211_hwsim, from Jinbum Park.
7) Missing rhashtable_walk_exit() in tipc, from Cong Wang.
8) Revert kvzalloc() conversion of AF_PACKET, it breaks mmap() when
kvzalloc() tries to use kmalloc() pages. From Eric Dumazet.
9) Fix deadlock in hv_netvsc, from Dexuan Cui.
10) Do not restart timewait timer on RST, from Florian Westphal.
11) Fix double lwstate refcount grab in ipv6, from Alexey Kodanev.
12) Unsolicit report count handling is off-by-one, fix from Hangbin Liu.
13) Sleep-in-atomic in cadence driver, from Jia-Ju Bai.
14) Respect ttl-inherit in ip6 tunnel driver, from Hangbin Liu.
15) Use-after-free in act_ife, fix from Cong Wang.
16) Missing hold to meta module in act_ife, from Vlad Buslov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (91 commits)
net: phy: sfp: Handle unimplemented hwmon limits and alarms
net: sched: action_ife: take reference to meta module
act_ife: fix a potential use-after-free
net/mlx5: Fix SQ offset in QPs with small RQ
tipc: correct spelling errors for tipc_topsrv_queue_evt() comments
tipc: correct spelling errors for struct tipc_bc_base's comment
bnxt_en: Do not adjust max_cp_rings by the ones used by RDMA.
bnxt_en: Clean up unused functions.
bnxt_en: Fix firmware signaled resource change logic in open.
sctp: not traverse asoc trans list if non-ipv6 trans exists for ipv6_flowlabel
sctp: fix invalid reference to the index variable of the iterator
net/ibm/emac: wrong emac_calc_base call was used by typo
net: sched: null actions array pointer before releasing action
vhost: fix VHOST_GET_BACKEND_FEATURES ioctl request definition
r8169: add support for NCube 8168 network card
ip6_tunnel: respect ttl inherit for ip6tnl
mac80211: shorten the IBSS debug messages
mac80211: don't Tx a deauth frame if the AP forbade Tx
mac80211: Fix station bandwidth setting after channel switch
mac80211: fix a race between restart and CSA flows
...
Not all SFPs implement the registers containing sensor limits and
alarms. Luckily, there is a bit indicating if they are implemented or
not. Add checking for this bit, when deciding if the hwmon attributes
should be visible.
Fixes: 1323061a01 ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1077614 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Immediately after module_put(), user could delete this
module, so e->ops could be already freed before we call
e->ops->release().
Fix this by moving module_put() after ops->release().
Fixes: ef6980b6be ("introduce IFE action")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the formula for calculating the RQ page remainder,
which should be in byte granularity. The result will be
non-zero only for RQs smaller than PAGE_SIZE, as an RQ size
is a power of 2.
Divide this by the SQ stride (MLX5_SEND_WQE_BB) to get the
SQ offset in strides granularity.
Fixes: d7037ad73d ("net/mlx5: Fix QP fragmented buffer allocation")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VSC8584 supports 4 LEDs while VSC8531 only supports 2. Let's factorize
the documentation for LED mode properties and give the 4 default values
(the first two being shared between VSC8531 and VSC8584).
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Brauner