.check_plane() already gets the plane state, so we can dig out the plane
from there if needed. No need in passing it separately.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180828142707.31583-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
gcc is too smart for us and doesn't evaluate BUILD_BUG_ON()s in
unused static inlines. Collect them up in one static inline and
actually call it to make sure gcc sees it.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180828133723.18505-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
We currently verify that all doorbells can be registered with GuC and
HW but don't check that all works as expected after a db ring.
Do a nop ring of all doorbells to make sure we haven't misprogrammed
any WQ or stage descriptor data. This will also help validating
upcoming changes in the db programming flow.
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Acked-by: Katarzyna Dec <katarzyna.dec@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180827223614.22789-1-daniele.ceraolospurio@intel.com
CI runs show PSR2 does not go to IDLE with selective update enabled on
all PSR exit triggers. Specifically, logs indicate the hardware enters
"SLEEP Selective Update" and not "IDLE Reset state', like the kernel
expects, when vblank interrupts are enabled. This check was added for PSR1
but incorrectly extended to PSR2, remove the check as it breaks tests
and prints out misleading error messages.
v2: Split out non-code changes (Rodrigo)
Cc: Tarun Vyas <tarun.vyas@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Fixes: c43dbcbbcc ("drm/i915/psr: Lockless version of psr_wait_for_idle")
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180824230844.12428-1-dhinakaran.pandiyan@intel.com
This re-applies the workaround for "some DP sinks, [which] are a
little nuts" from commit 1a36147bb9 ("drm/i915: Perform link
quality check unconditionally during long pulse").
It makes the secondary AOC E2460P monitor connected via DP to an
acer Veriton N4640G usable again.
This hunk was dropped in commit c85d200e83 ("drm/i915: Move SST
DP link retraining into the ->post_hotplug() hook")
Fixes: c85d200e83 ("drm/i915: Move SST DP link retraining into the ->post_hotplug() hook")
[Cleaned up commit message, added stable cc]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jan-Marek Glogowski <glogow@fbihome.de>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20180825191035.3945-1-lyude@redhat.com
None of the current lookup_power_well() callers are actually checking
for NULL return values, they all just use the pointer right away. The
first idea was to replace these theoretical segfaults with a BUG()
since this would at least make our code a little more explicit to the
reader. It was suggested that just converting the BUG() to a WARN()
and returning any power well would probably be better since it would
still keep the system running while at the same time exposing the
driver bug.
We can only hit this NULL/BUG()/WARN() condition if we try to lookup a
power well that isn't defined on a given platform. If that ever
happens, we have to fix our code, making it lookup the correct power
well. Because of this, I don't think it's worth trying to implement
error checking in every caller. Improving our CI system will be a
better use of our time once a bug is found in the wild.
v2: Avoid the BUG() with a WARN() return a random PW (Michal).
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180820233139.11936-2-paulo.r.zanoni@intel.com
Unlike the other ports, TC ports are not available to use as soon as
we get a hotplug. The TC PHYs can be shared between multiple
controllers: display, USB, etc. As a result, handshaking through FIA
is required around connect and disconnect to cleanly transfer
ownership with the controller and set the type-C power state.
This patch implements the flow sequences described by our
specification. We opt to grab ownership of the ports as soon as we get
the hotplugs in order to simplify the interactions and avoid surprises
in the user space side. We may consider changing this in the future,
once we improve our testing capabilities on this area.
v2:
* This unifies the DP and HDMI patches so we can discuss everything
at once so people looking at random single patches can actually
understand the direction.
* I found out the spec was updated a while ago. There's a small
difference in the connect flow and the patch was updated for that.
* Our spec also now gives a good explanation on what is really
happening. As a result, comments were added.
* Add some more comments as requested by Rodrigo (Rodrigo).
v3:
* Downgrade a DRM_ERROR that shouldn't ever happen but we can't act
on in case it does (Chris).
BSpec: 21750, 4250.
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180801173441.9789-1-paulo.r.zanoni@intel.com
We use kzalloc to allocate the write_buf that we use for
i2c transfer on hdcp write. But it seems that we are forgetting
to free the memory that is not needed after i2c transfer is
completed.
Reported-by: Brian J Wood <brian.j.wood@intel.com>
Fixes: 2320175feb ("drm/i915: Implement HDCP for HDMI")
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180823205136.31310-1-rodrigo.vivi@intel.com
For S0ix we want to deinit power domains (and so deactivate the DMC
firmware) exactly when the platform supports the DC9 state. To reach
S0ix we need DC9 on these platforms (for which the DMC FW needs to be
deactivated) while to reach S0ix on the rest of the DMC platforms we
need DC6 (which needs the DMC FW to stay active).
Simplify the condition accordingly so it will be automatically
correct for upcoming DC9 platforms like ICL.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180822112602.27543-1-imre.deak@intel.com
Commit cafa0010cd ("Raise the minimum required gcc version to 4.6")
recently exposed a brittle part of the build for supporting non-gcc
compilers.
Both Clang and ICC define __GNUC__, __GNUC_MINOR__, and
__GNUC_PATCHLEVEL__ for quick compatibility with code bases that haven't
added compiler specific checks for __clang__ or __INTEL_COMPILER.
This is brittle, as they happened to get compatibility by posing as a
certain version of GCC. This broke when upgrading the minimal version
of GCC required to build the kernel, to a version above what ICC and
Clang claim to be.
Rather than always including compiler-gcc.h then undefining or
redefining macros in compiler-intel.h or compiler-clang.h, let's
separate out the compiler specific macro definitions into mutually
exclusive headers, do more proper compiler detection, and keep shared
definitions in compiler_types.h.
Fixes: cafa0010cd ("Raise the minimum required gcc version to 4.6")
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Eli Friedman <efriedma@codeaurora.org>
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are several blockable mmu notifiers which might sleep in
mmu_notifier_invalidate_range_start and that is a problem for the
oom_reaper because it needs to guarantee a forward progress so it cannot
depend on any sleepable locks.
Currently we simply back off and mark an oom victim with blockable mmu
notifiers as done after a short sleep. That can result in selecting a new
oom victim prematurely because the previous one still hasn't torn its
memory down yet.
We can do much better though. Even if mmu notifiers use sleepable locks
there is no reason to automatically assume those locks are held. Moreover
majority of notifiers only care about a portion of the address space and
there is absolutely zero reason to fail when we are unmapping an unrelated
range. Many notifiers do really block and wait for HW which is harder to
handle and we have to bail out though.
This patch handles the low hanging fruit.
__mmu_notifier_invalidate_range_start gets a blockable flag and callbacks
are not allowed to sleep if the flag is set to false. This is achieved by
using trylock instead of the sleepable lock for most callbacks and
continue as long as we do not block down the call chain.
I think we can improve that even further because there is a common pattern
to do a range lookup first and then do something about that. The first
part can be done without a sleeping lock in most cases AFAICS.
The oom_reaper end then simply retries if there is at least one notifier
which couldn't make any progress in !blockable mode. A retry loop is
already implemented to wait for the mmap_sem and this is basically the
same thing.
The simplest way for driver developers to test this code path is to wrap
userspace code which uses these notifiers into a memcg and set the hard
limit to hit the oom. This can be done e.g. after the test faults in all
the mmu notifier managed memory and set the hard limit to something really
small. Then we are looking for a proper process tear down.
[akpm@linux-foundation.org: coding style fixes]
[akpm@linux-foundation.org: minor code simplification]
Link: http://lkml.kernel.org/r/20180716115058.5559-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Christian König <christian.koenig@amd.com> # AMD notifiers
Acked-by: Leon Romanovsky <leonro@mellanox.com> # mlx and umem_odp
Reported-by: David Rientjes <rientjes@google.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Sudeep Dutt <sudeep.dutt@intel.com>
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch make changes to allocate crc-entries buffer before
enabling CRC generation.
It moves all the failure check early in the function before setting
the source or memory allocation.
Now set_crc_source takes only two variable inputs, values_cnt we
already gets as part of verify_crc_source.
Changes since V1:
- refactor code to use single spin lock
Changes since V2:
- rebase
Changes since V3:
- rebase on top of VKMS driver
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Haneen Mohammed <hamohammed.sa@gmail.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Leo Li <sunpeng.li@amd.com> (V2)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> (V3)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180821083858.26275-3-mahesh1.kumar@intel.com
The workaround was supposed to look at the plane destination
coordinates. Currently it's looking at some mixture of src
and dst coordinates that doesn't make sense. Fix it up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180719182214.4323-2-ville.syrjala@linux.intel.com
Fixes: 394676f05b (drm/i915: Add WA for planes ending close to left screen edge)
Reviewed-by: Imre Deak <imre.deak@intel.com>
gen8_de_irq_postinstall() wasn't masking the IRQ bit before passing the
debug flag to psr_irq_control(). This check was missed when new debug bits
were defined in 'commit c44301fce6 ("drm/i915: Allow control of PSR at
runtime through debugfs, v6")'. Instead of ANDing the irq bit in all the
callers, move it to the callee.
v2: Rebased.
Fixes: c44301fce6 ("drm/i915: Allow control of PSR at runtime through
debugfs, v6")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180821221156.2442-3-dhinakaran.pandiyan@intel.com
We print the last attempted entry and last exit timestamps only when
IRQ debug is requested. This check was missed when new debug flags were
added in 'commit c44301fce6 ("drm/i915: Allow control of PSR at
runtime through debugfs, v6")
Fixes: c44301fce6 ("drm/i915: Allow control of PSR at runtime through
debugfs, v6")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180821221156.2442-2-dhinakaran.pandiyan@intel.com
Knowing the status of the PSR HW state machine is useful for debug,
especially since we are seeing errors with PSR2 in CI.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180821221156.2442-1-dhinakaran.pandiyan@intel.com
Since we no longer maintain our read position in the CSB pointers
register, it always returns 0 and not where we last read up to. As a
result the CSB probing in the state dumper starts from 0, either missing
entries or showing stale one.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180821101138.15822-1-chris@chris-wilson.co.uk
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
- New Device Support
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
- New Functionality
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
- Fix-ups
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
- Bug Fixes
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501
-----BEGIN PGP SIGNATURE-----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=4Yj4
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
mfd: bd71837: Core driver for ROHM BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
PLLs are the source clocks for the DDIs so in order to determine the
ddi clock we need to check the PLL configuration.
For MG PHy Ports (C - F), depending on whether it is a TBT PLL or MG
PLL the link lock can be obtained from the the PLL divisors based on
the specification.
v2 (from Paulo):
* Make the algorithm look more like what's in the spec, also document
where we differ form the spec and why.
* Make the code a little more consistent with our coding style.
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180817215209.29133-2-paulo.r.zanoni@intel.com
The register value of Divider Ratio for high speed divider
(hsdiv_ratio) in MG_CLKTOP2_HSCLKCTL_PORT register is not same as the
actual numerical value of the divider. So this patch implements
separate divider value defines for that field.
icl_mg_pll_find_divisors() can use these defines instead of magic
register values.
The new defines are going to be used in the next patch.
v2 (from Paulo):
* Rebase.
* Make it look a little more like the rest of our code.
v3 (from Paulo):
* Make hsdiv u32 now that it's a bit field (José).
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Suggested-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180817215209.29133-1-paulo.r.zanoni@intel.com
If the display has been disabled by modparam, we still want to connect
together the HW bits and bobs with the associated drivers so that we can
continue to manage their runtime power gating.
Fixes: 108109444f ("drm/i915: Check num_pipes before initializing audio component")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Elaine Wang <elaine.wang@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180817100241.4628-1-chris@chris-wilson.co.uk
100 ms is not enough time for the LSPCON adapter on Intel NUC devices to
settle. This causes dropped display modes at boot or screen reconfiguration.
Empirical testing can reproduce the error up to a timeout of 190 ms. Basic
boot and stress testing at 200 ms has not (yet) failed.
Increase timeout to 400 ms to get some margin of error.
Changes from v1:
The initial suggestion of 1000 ms was lowered due to concerns about delaying
valid timeout cases.
Update patch metadata.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107503
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1570392
Fixes: 357c0ae919 ("drm/i915/lspcon: Wait for expected LSPCON mode to settle")
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v4.11+
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Fredrik Schön <fredrik.schon@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180817200728.8154-1-fredrik.schon@gmail.com
After
commit 2cd9a689e9 ("drm/i915: Refactor intel_display_set_init_power() logic")
it makes more sense to check the power domain/well refcounts after
enabling the power domains functionality. Before that it's guaranteed
that most power wells (in the INIT domain) will have a reference held,
so not an interesting state.
While at it also add the check after the init_hw/fini_hw, disable and
suspend/resume steps. Make the test optional on a Kconfig option since
it may add substantial overhead: on VLV/CHV the corresponding PUNIT reg
access for each power well may take up to 20ms.
v2:
- Add the state check to more spots. (Chris)
v3:
- During suspend check the state before deiniting display core.
Afterwards DC states are disabled (and so the dc_off power well is
enabled) even though we don't hold a reference on it.
- Do the test conditionally based on a new Kconfig option. (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[Add DRM_I915_DEBUG_RUNTIME_PM to welcome messages]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180817145837.26592-1-imre.deak@intel.com
Let us reuse the already defined has_csr check and not
redefine it.
The main difference is that in effect this will flip .has_csr to 1
(via GEN9_FEATURES which GEN11_FEATURES pulls in).
Suggested-by: Imre Deak <imre.deak@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=107382
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1534527210-16841-1-git-send-email-anusha.srivatsa@intel.com
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJbdhlUAAoJEAx081l5xIa++08P/jdvasJkTu3eyAczNVW2EPyG
JQcpIj774tyN0Dwy9rjkW5KxlNo5cQlchlAQ/LqPnRJp8c3qSe3obwjFzmXkQgxP
j//1FB1XkxK/YZbXRjudV7xUov/sMyBnXIwvmWP3NDu5rDrWfLZDznvq6r7vDy/o
ImmxZboWqI94oGhrtAuwMpcFjOOuOvJQg9FSHAOMkNhRHs1xl50y5R/WSeAoY1fC
R22SZEcGQkQJuq6kHa2Dgysd1uMULLpgQnbw/9rD72PeQXzIIw48xdjJkTBjPu5A
ulrCaMd+loaCO3xdtIdpLqbKo4XQwGCm1gShDUWZhgVy21Z3M78u6isEtBkYDbZZ
MJECEYzbp8EYkm8QiqSzTTdqvrlH3CjukKhhZeNdpVNxmIvsjZDQGTKYp21mA3S1
I+FVPFH6sykMFxIcpRa87bn4ImrJ2xSDSrWU3HhNQiWpJf+fSaZsKQkUCLdY9rxX
WcwvtP5zspL0rWwtkStkKd0BSkBK+S6uZ17xlvUEK17kih2E2TTpJoGnqNE1HNUP
7Kts/UgXrxobSGhRJLxf+b7gJqWwrLmeCfF4ZWRvMpG727k6Dw87mIfkMGy0v/fJ
rKp2/RYqPGVF2A++2kp5GFPfIFlHtiCCDNYwoBJKqwCFkm+ow+ehFWwLXPXeBDFH
PRfMeYj5freNp2C78TTD
=RsR5
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-08-17' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"First round of fixes for -rc1. I'll follow this up with the msm new hw
support pull request.
This just has three sets of fixes, some for msm before the new hw, a
bunch of AMD fixes (includiing some required firmware changes for new
hw), and a set of i915 (+gvt) fixes"
* tag 'drm-next-2018-08-17' of git://anongit.freedesktop.org/drm/drm: (30 commits)
drm/amdgpu: Use kvmalloc for allocating UVD/VCE/VCN BO backup memory
drm/i915: set DP Main Stream Attribute for color range on DDI platforms
drm/i915/selftests: Hold rpm for unparking
drm/i915: Restore user forcewake domains across suspend
drm/i915: Unmask user interrupts writes into HWSP on snb/ivb/vlv/hsw
drm/i915/gvt: fix memory leak in intel_vgpu_ioctl()
drm/i915/gvt: Off by one in intel_vgpu_write_fence()
drm/i915/kvmgt: Fix potential Spectre v1
drm/i915/gvt: return error on cmd access
drm/i915/gvt: initialize dmabuf mutex in vgpu_create
drm/i915/gvt: fix cleanup sequence in intel_gvt_clean_device
drm/amd/display: Guard against null crtc in CRC IRQ
drm/amd/display: Pass connector id when executing VBIOS CT
drm/amd/display: Check if clock source in use before disabling
drm/amd/display: Allow clock sharing b/w HDMI and DVI
drm/amd/display: Fix warning observed in mode change on Vega
drm/amd/display: fix single link DVI has no display
drm/amdgpu/vce: VCE entity initialization relies on ring initializtion
drm/amdgpu/uvd: UVD entity initialization relys on ring initialization
drm/amdgpu:add VCN booting with firmware loaded by PSP
...
dma_fence_default_wait is the default now, same for the trivial
enable_signaling implementation.
v2: Also remove the relase hook, dma_fence_free is the default.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20180704092909.6599-2-daniel.vetter@ffwll.ch
Instead of defining all registers twice, define just a PCH_GPIO_BASE
that has the same address as PCH_GPIO_A and use that to calculate all
the others. This also brings VLV and !HAS_GMCH_DISPLAY in line, doing
the same thing.
v2: Fix GMBUS registers to be relative to gpio base; create GPIO()
macro to return a particular gpio address and move the enum out of
i915_reg.h (suggested by Jani)
v3: Move base offset inside the GPIO() macro so the GMBUS defines don't
actually need to be changed (suggested by Daniel/Ville)
v4: Move definition of i915_gpio to intel_display.h and remove
GMBUS/GPIO handling from gvt since now they have their own
defines.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180727193647.8639-3-lucas.demarchi@intel.com
The definition on i915_reg.h is going to change to depend on
dev_priv->gpio_mmio_base being properly initialized. Define our own
macros since init_generic_mmio_info() is called before than
gpio_mmio_base being set.
Cc: intel-gvt-dev@lists.freedesktop.org
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180727193647.8639-2-lucas.demarchi@intel.com
The device global init_power_on flag is somewhat arbitrary and makes
debugging power refcounting problems difficult. Instead arrange things
so that all display power domain get has a corresponding put call. After
this change we have the following sequences:
driver loading:
intel_power_domains_init_hw();
<other init steps>
intel_power_domains_enable();
driver unloading:
intel_power_domains_disable();
<other uninit steps>
intel_power_domains_fini_hw();
system suspend:
intel_power_domains_disable();
<other suspend steps>
intel_power_domains_suspend();
system resume:
intel_power_domains_resume();
<other resume steps>
intel_power_domains_enable();
at other times while the driver is loaded:
intel_display_power_get();
...
intel_display_power_put();
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180816123757.3286-2-imre.deak@intel.com
Currently, we cancel the extra wakeref we have for !runtime-pm devices
inside power_wells_fini_hw. However, this is not strictly paired with
the acquisition of that wakeref in runtime_pm_enable (as the fini_hw may
be called on errors paths before we even call runtime_pm_enable). Make
the symmetry more explicit and include a check that we do release all of
our rpm wakerefs.
v2: Fixup transfer of ownership back to core whilst keeping our wakeref
count balanced.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180816123757.3286-1-imre.deak@intel.com
The context owns both the ppgtt and the vma within it, and our activity
tracking on the context ensures that we do not release active ppgtt. As
the context fulfils our obligations for active memory tracking, we can
relinquish the reference from the vma.
This fixes a silly transient refleak from closed vma being kept alive
until the entire system was idle, keeping all vm alive as well.
Reported-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Testcase: igt/gem_ctx_create/files
Fixes: 3365e2268b ("drm/i915: Lazily unbind vma on close")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Tested-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180816073448.19396-1-chris@chris-wilson.co.uk
-----BEGIN PGP SIGNATURE-----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=g9rD
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.19.
Rob has some new hardware support for new qualcomm hw that I'll send
along separately. This has the display part of it, the remaining pull
is for the acceleration engine.
This also contains a wound-wait/wait-die mutex rework, Peter has acked
it for merging via my tree.
Otherwise mostly the usual level of activity. Summary:
core:
- Wound-wait/wait-die mutex rework
- Add writeback connector type
- Add "content type" property for HDMI
- Move GEM bo to drm_framebuffer
- Initial gpu scheduler documentation
- GPU scheduler fixes for dying processes
- Console deferred fbcon takeover support
- Displayport support for CEC tunneling over AUX
panel:
- otm8009a panel driver fixes
- Innolux TV123WAM and G070Y2-L01 panel driver
- Ilitek ILI9881c panel driver
- Rocktech RK070ER9427 LCD
- EDT ETM0700G0EDH6 and EDT ETM0700G0BDH6
- DLC DLC0700YZG-1
- BOE HV070WSA-100
- newhaven, nhd-4.3-480272ef-atxl LCD
- DataImage SCF0700C48GGU18
- Sharp LQ035Q7DB03
- p079zca: Refactor to support multiple panels
tinydrm:
- ILI9341 display panel
New driver:
- vkms - virtual kms driver to testing.
i915:
- Icelake:
Display enablement
DSI support
IRQ support
Powerwell support
- GPU reset fixes and improvements
- Full ppgtt support refactoring
- PSR fixes and improvements
- Execlist improvments
- GuC related fixes
amdgpu:
- Initial amdgpu documentation
- JPEG engine support on VCN
- CIK uses powerplay by default
- Move to using core PCIE functionality for gens/lanes
- DC/Powerplay interface rework
- Stutter mode support for RV
- Vega12 Powerplay updates
- GFXOFF fixes
- GPUVM fault debugging
- Vega12 GFXOFF
- DC improvements
- DC i2c/aux changes
- UVD 7.2 fixes
- Powerplay fixes for Polaris12, CZ/ST
- command submission bo_list fixes
amdkfd:
- Raven support
- Power management fixes
udl:
- Cleanups and fixes
nouveau:
- misc fixes and cleanups.
msm:
- DPU1 support display controller in sdm845
- GPU coredump support.
vmwgfx:
- Atomic modesetting validation fixes
- Support for multisample surfaces
armada:
- Atomic modesetting support completed.
exynos:
- IPPv2 fixes
- Move g2d to component framework
- Suspend/resume support cleanups
- Driver cleanups
imx:
- CSI configuration improvements
- Driver cleanups
- Use atomic suspend/resume helpers
- ipu-v3 V4L2 XRGB32/XBGR32 support
pl111:
- Add Nomadik LCDC variant
v3d:
- GPU scheduler jobs management
sun4i:
- R40 display engine support
- TCON TOP driver
mediatek:
- MT2712 SoC support
rockchip:
- vop fixes
omapdrm:
- Workaround for DRA7 errata i932
- Fix mm_list locking
mali-dp:
- Writeback implementation
PM improvements
- Internal error reporting debugfs
tilcdc:
- Single fix for deferred probing
hdlcd:
- Teardown fixes
tda998x:
- Converted to a bridge driver.
etnaviv:
- Misc fixes"
* tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm: (1506 commits)
drm/amdgpu/sriov: give 8s for recover vram under RUNTIME
drm/scheduler: fix param documentation
drm/i2c: tda998x: correct PLL divider calculation
drm/i2c: tda998x: get rid of private fill_modes function
drm/i2c: tda998x: move mode_valid() to bridge
drm/i2c: tda998x: register bridge outside of component helper
drm/i2c: tda998x: cleanup from previous changes
drm/i2c: tda998x: allocate tda998x_priv inside tda998x_create()
drm/i2c: tda998x: convert to bridge driver
drm/scheduler: fix timeout worker setup for out of order job completions
drm/amd/display: display connected to dp-1 does not light up
drm/amd/display: update clk for various HDMI color depths
drm/amd/display: program display clock on cache match
drm/amd/display: Add NULL check for enabling dp ss
drm/amd/display: add vbios table check for enabling dp ss
drm/amd/display: Don't share clk source between DP and HDMI
drm/amd/display: Fix DP HBR2 Eye Diagram Pattern on Carrizo
drm/amd/display: Use calculated disp_clk_khz value for dce110
drm/amd/display: Implement custom degamma lut on dcn
drm/amd/display: Destroy aux_engines only once
...
Since Haswell we have no color range indication either in the pipe or
port registers for DP. Instead, there's a separate register for setting
the DP Main Stream Attributes (MSA) directly. The MSA register
definition makes no references to colorimetry, just a vague reference to
the DP spec. The connection to the color range was lost.
Apparently we've failed to set the proper MSA bit for limited, or CEA,
range ever since the first DDI platforms. We've started setting other
MSA parameters since commit dae847991a ("drm/i915: add
intel_ddi_set_pipe_settings").
Without the crucial bit of information, the DP sink has no way of
knowing the source is actually transmitting limited range RGB, leading
to "washed out" colors. With the colorimetry information, compliant
sinks should be able to handle the limited range properly. Native
(i.e. non-LSPCON) HDMI was not affected because we do pass the color
range via AVI infoframes.
Though not the root cause, the problem was made worse for DDI platforms
with commit 55bc60db59 ("drm/i915: Add "Automatic" mode for the
"Broadcast RGB" property"), which selects limited range RGB
automatically based on the mode, as per the DP, HDMI and CEA specs.
After all these years, the fix boils down to flipping one bit.
[Per testing reports, this fixes DP sinks, but not the LSPCON. My
educated guess is that the LSPCON fails to turn the CEA range MSA into
AVI infoframes for HDMI.]
Reported-by: Michał Kopeć <mkopec12@gmail.com>
Reported-by: N. W. <nw9165-3201@yahoo.com>
Reported-by: Nicholas Stommel <nicholas.stommel@gmail.com>
Reported-by: Tom Yan <tom.ty89@gmail.com>
Tested-by: Nicholas Stommel <nicholas.stommel@gmail.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=100023
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107476
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94921
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.9+
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180814060001.18224-1-jani.nikula@intel.com
(cherry picked from commit dc5977da99)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The call to i915_gem_unpark() checks that we hold a rpm wakeref before
taking a long term wakeref for i915->gt.awake. We should therefore make
sure we do hold the wakeref when directly calling unpark to disable
the retire worker.
Fixes: 932cac10c8 ("drm/i915/selftests: Prevent background reaping of active objects")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180809063449.4474-1-chris@chris-wilson.co.uk
(cherry picked from commit 7b5ee80a5d)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
On suspend, we cancel the automatic forcewake and clear all other sources
of forcewake so the machine can sleep before we do suspend. However, we
expose the forcewake to userspace (only via debugfs, but nevertheless we
do) and want to restore that upon resume or else our accounting will be
off and we may not acquire the forcewake before we use it. So record
which domains we cleared on suspend and reacquire them early on resume.
v2: Hold the spinlock to appease our sanitychecks
v3: s/fw_domains_user/fw_domains_saved/ to convey intent more clearly
Reported-by: Imre Deak <imre.deak@linux.intel.com>
Fixes: b847305080 ("drm/i915: Fix forcewake active domain tracking")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Imre Deak <imre.deak@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180808210842.3555-1-chris@chris-wilson.co.uk
(cherry picked from commit d60996ab43)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
An oddity occurs on Sandybridge, Ivybridge and Haswell (and presumably
Valleyview) in that for the period following the GPU restart after a
reset, there are no GT interrupts received. From Ville's notes, bit 0 in
the HWSTAM corresponds to the render interrupt, and if we unmask it we
do see immediate resumption of GT interrupt delivery (via the master irq
handler) after the reset.
v2: Limit the w/a to the render interrupt from rcs
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107500
Fixes: c549808946 ("drm/i915: Mask everything in ring HWSTAM on gen6+ in ringbuffer mode")
References: d420a50c21 ("drm/i915: Clean up the HWSTAM mess")
Testcase: igt/gem_eio/reset-stress
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180808105101.913-2-chris@chris-wilson.co.uk
(cherry picked from commit a4a717010f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The case where the firmware isn't specified for a platform (although
runtime PM works only with DMC on this platform) is the same case where
the firmware is specified but can't be loaded for some reason. Hence we
need to get a display init power domain ref in the first case too to
keep the refcount bookkeeping in balance.
Also convert the related log message to be a debug one, since it's a
valid scenario for a new platform, where we need to have
dev_info->has_csr=1 set, but add support for actually loading the
firmware only later.
v2:
- In addition to the debug log, WARN on non-alpha support platforms,
since then the first case isn't valid scenario. (Chris)
References: https://bugs.freedesktop.org/show_bug.cgi?id=107382
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180815131038.24446-1-imre.deak@intel.com
If we pardon a per-engine reset, we may leave the STOP_RING bit asserted
in RING_MI_MODE resulting in the engine hanging. Unconditionally clear
it on the per-engine exit path as we know that either we skipped the
reset and so need the cancellation, or the reset was successful and the
cancellation is a no-op, or there was an error and we will follow up
with a full-reset or wedging (both of which will stop the engines again
as required).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107188
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106560
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180814171857.24673-1-chris@chris-wilson.co.uk
It's been busy summer weeks and hence lots of changes, partly for a
few new drivers and partly for a wide range of fixes.
Here are highlights:
ALSA Core:
- Fix rawmidi buffer management, code cleanup / refactoring
- Fix the SG-buffer page handling with incorrect fallback size
- Fix the stall at virmidi trigger callback with a large buffer;
also offloading and code-refactoring along with it
- Various ALSA sequencer code cleanups
ASoC:
- Deploy the standard snd_pcm_stop_xrun() helper in several drivers
- Support for providing name prefixes to generic component nodes
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing
- Generalization of the DIO2125 support to a simple amplifier driver
- Accessory detection support for the audio graph card
- DT support for PXA AC'97 devices
- Quirks for a number of new x86 systems
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707
HD-audio:
- Code refactoring in HD-audio ext codec codes to drop own classes;
preliminary works for the upcoming legacy codec support
- Generalized DRM audio component for the upcoming radeon / amdgpu
support
- Unification of mic mute-LED and GPIO support for various codecs
- Further improvement of CA0132 codec support including Recon3D
- Proper vga_switcheroo handling for AMD i-GPU
- Update of model list in documentation
- Fixups for another HP Spectre x360, Conexant codecs, power-save
blacklist update
USB-audio:
- Fix the invalid sample rate setup with external clock
- Support of UAC3 selector units and processing units
- Basic UAC3 power-domain support
- Support for Encore mDSD and Thesycon-based DSD devices
- Preparation for future complete callback changes
Firewire:
- Add support for MOTU Traveler
Misc:
- The endianess notation fixes in various drivers
- Add fall-through comment in lots of drivers
- Various sparse warning fixes, e.g. about PCM format types
-----BEGIN PGP SIGNATURE-----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=eTIC
-----END PGP SIGNATURE-----
Merge tag 'sound-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It's been busy summer weeks and hence lots of changes, partly for a
few new drivers and partly for a wide range of fixes.
Here are highlights:
ALSA Core:
- Fix rawmidi buffer management, code cleanup / refactoring
- Fix the SG-buffer page handling with incorrect fallback size
- Fix the stall at virmidi trigger callback with a large buffer; also
offloading and code-refactoring along with it
- Various ALSA sequencer code cleanups
ASoC:
- Deploy the standard snd_pcm_stop_xrun() helper in several drivers
- Support for providing name prefixes to generic component nodes
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing
- Generalization of the DIO2125 support to a simple amplifier driver
- Accessory detection support for the audio graph card
- DT support for PXA AC'97 devices
- Quirks for a number of new x86 systems
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707
HD-audio:
- Code refactoring in HD-audio ext codec codes to drop own classes;
preliminary works for the upcoming legacy codec support
- Generalized DRM audio component for the upcoming radeon / amdgpu
support
- Unification of mic mute-LED and GPIO support for various codecs
- Further improvement of CA0132 codec support including Recon3D
- Proper vga_switcheroo handling for AMD i-GPU
- Update of model list in documentation
- Fixups for another HP Spectre x360, Conexant codecs, power-save
blacklist update
USB-audio:
- Fix the invalid sample rate setup with external clock
- Support of UAC3 selector units and processing units
- Basic UAC3 power-domain support
- Support for Encore mDSD and Thesycon-based DSD devices
- Preparation for future complete callback changes
Firewire:
- Add support for MOTU Traveler
Misc:
- The endianess notation fixes in various drivers
- Add fall-through comment in lots of drivers
- Various sparse warning fixes, e.g. about PCM format types"
* tag 'sound-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (529 commits)
ASoC: adav80x: mark expected switch fall-through
ASoC: da7219: Add delays to capture path to remove DC offset noise
ALSA: usb-audio: Mark expected switch fall-through
ALSA: mixart: Mark expected switch fall-through
ALSA: opl3: Mark expected switch fall-through
ALSA: hda/ca0132 - Add exit commands for Recon3D
ALSA: hda/ca0132 - Change mixer controls for Recon3D
ALSA: hda/ca0132 - Add Recon3D input and output select commands
ALSA: hda/ca0132 - Add DSP setup defaults for Recon3D
ALSA: hda/ca0132 - Add Recon3D startup functions and setup
ALSA: hda/ca0132 - Add bool variable to enable/disable pci region2 mmio
ALSA: hda/ca0132 - Add Recon3D pincfg
ALSA: hda/ca0132 - Add quirk ID and enum for Recon3D
ALSA: hda/ca0132 - Add alt_functions unsolicited response
ALSA: hda/ca0132 - Clean up ca0132_init function.
ALSA: hda/ca0132 - Create mmio gpio function to make code clearer
ASoC: wm_adsp: Make DSP name configurable by codec driver
ASoC: wm_adsp: Declare firmware controls from codec driver
ASoC: max98373: Added software reset register to readable registers
ASoC: wm_adsp: Correct DSP pointer for preloader control
...
If we cannot setup rc6, we cannot let the GPU suspend itself as it
cannot save its state (to a powercontext). As such, we must disable
runtime-pm, but we should do so using the low-level pm-runtime function
which leaves our own debugging functions intact (and continue to detect
errors in our runtime-pm handling should we ever be able to enable rc6).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180812223642.24865-3-chris@chris-wilson.co.uk
Since Haswell we have no color range indication either in the pipe or
port registers for DP. Instead, there's a separate register for setting
the DP Main Stream Attributes (MSA) directly. The MSA register
definition makes no references to colorimetry, just a vague reference to
the DP spec. The connection to the color range was lost.
Apparently we've failed to set the proper MSA bit for limited, or CEA,
range ever since the first DDI platforms. We've started setting other
MSA parameters since commit dae847991a ("drm/i915: add
intel_ddi_set_pipe_settings").
Without the crucial bit of information, the DP sink has no way of
knowing the source is actually transmitting limited range RGB, leading
to "washed out" colors. With the colorimetry information, compliant
sinks should be able to handle the limited range properly. Native
(i.e. non-LSPCON) HDMI was not affected because we do pass the color
range via AVI infoframes.
Though not the root cause, the problem was made worse for DDI platforms
with commit 55bc60db59 ("drm/i915: Add "Automatic" mode for the
"Broadcast RGB" property"), which selects limited range RGB
automatically based on the mode, as per the DP, HDMI and CEA specs.
After all these years, the fix boils down to flipping one bit.
[Per testing reports, this fixes DP sinks, but not the LSPCON. My
educated guess is that the LSPCON fails to turn the CEA range MSA into
AVI infoframes for HDMI.]
Reported-by: Michał Kopeć <mkopec12@gmail.com>
Reported-by: N. W. <nw9165-3201@yahoo.com>
Reported-by: Nicholas Stommel <nicholas.stommel@gmail.com>
Reported-by: Tom Yan <tom.ty89@gmail.com>
Tested-by: Nicholas Stommel <nicholas.stommel@gmail.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=100023
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107476
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94921
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.9+
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180814060001.18224-1-jani.nikula@intel.com
This reapplies commit 39f3be162c ("drm/i915: Kick waiters on resetting
legacy rings") after the improved gem_eio was run across all machines we
found that gen3 and early gen4 still lost the immediate interrupt
following reset, and the HWSTAM w/a applied to gen6+ is inadequate.
Unlike the later gen, on gen3/4 the principle (and only tests to fail so
far) are the wait vs reset test cases, whereas the reset stress case
works fine (which was the predominantly failing case for gen6+). That is
enough to suggest the underlying issue is sufficiently different to
support the difference in HWSTAM efficacy.
Testcase: igt/gem_eio/wait-10ms
References: 39f3be162c ("drm/i915: Kick waiters on resetting legacy rings")
References: a69ab52b03 ("drm/i915: Remove extra waiter kick on legacy resets")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180814104056.27001-1-chris@chris-wilson.co.uk
The 'sparse' variable may leak when return in function
intel_vgpu_ioctl(), and this patch fix this.
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Reviewed-by: Jiang Biao <jiang.biao2@zte.com.cn>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
The > should be >= here so that we don't read one element beyond the
end of the array.
Fixes: 28a60dee2c ("drm/i915/gvt: vGPU HW resource management")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
info.index can be indirectly controlled by user-space, hence leading
to a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/gpu/drm/i915/gvt/kvmgt.c:1232 intel_vgpu_ioctl() warn:
potential spectre issue 'vgpu->vdev.region' [r]
Fix this by sanitizing info.index before indirectly using it to index
vgpu->vdev.region
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
If a register is not cmd accessible, should not just print error
message. Return error here so as not to deliver this cmd.
v2: return -EBADRQC to align with return value elsewhere. (kevin tian)
Signed-off-by: Zhao Yan <yan.y.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Currently, the mutex used in GVT dmabuf support is not initialized until
vgpu device is opened. If one vgpu device is opened and then removed, the
mutex will be used in vgpu remove operation without initialization. This
patch initializes the mutex in vgpu create operation to avoid the problem.
Fixes: e546e281d33d("drm/i915/gvt: Dmabuf support for GVT-g")
Signed-off-by: Hang Yuan <hang.yuan@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
If engine reports that it is not ready for reset, we
give up. Evidence shows that forcing a per engine reset
on an engine which is not reporting to be ready for reset,
can bring it back into a working order. There is risk that
we corrupt the context image currently executing on that
engine. But that is a risk worth taking as if we unblock
the engine, we prevent a whole device wedging in a case
of full gpu reset.
Reset individual engine even if it reports that it is not
prepared for reset, but only if we aim for full gpu reset
and not on first reset attempt.
v2: force reset only on later attempts, readability (Chris)
v3: simplify with adequate caffeine levels (Chris)
v4: comment about risks and migitations (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813130116.7250-1-mika.kuoppala@linux.intel.com
There is a possibility for per gen reset logic to
be more nasty if the softer approach on resetting does
not bear fruit.
Expose retry count to per gen reset logic if it
wants to take such tough measures.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180810140036.24240-1-mika.kuoppala@linux.intel.com
We require that we keep the list of outstanding work short so that we do
not "leak" memory while pageflipping under stress. However that system
stress may delay kernel workers virtually indefinitely, which incurs the
pageflips stall and eventually hit a timeout waiting for the cleanup.
Try to combat CPU starvation of our short-lived cleanup workers by
switching to a high priority workqueue.
Testcase: igt/kms_cursor_legacy/all-pipes-torture-move
References: https://bugs.freedesktop.org/show_bug.cgi?id=107122
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712115729.3506-1-chris@chris-wilson.co.uk
This patch implements get_crc_sources callback, which returns list of
all the valid crc sources supported by driver in current platform.
Changes since V1:
- Return array of crc sources
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180713135942.25061-8-mahesh1.kumar@intel.com
Some workloads may be prepared in vgpu's queue but not be scheduled
to run yet. If vgpu is released at this time, they will not be freed
in workload complete callback and so need to be freed in vgpu release
operation.
Add new vgpu_release operation in gvt_ops to stop vgpu and release
runtime resources. gvt_ops vgpu_deactivate operation will only stop
vgpu.
v2: add new gvt ops to clean vgpu running status (Xiong Zhang)
Signed-off-by: Hang Yuan <hang.yuan@linux.intel.com>
Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
The RS_CTX_ENABLE and CTX_SAVE_INHIBIT bits are not present on ICL
anymore, but we still try to set them and then check them with
GEM_BUG_ON, resulting in a BUG() call. The bug can be reproduced by
igt/drv_selftest/live_hangcheck/others-priority and our CI was able
to catch it.
It is worth noticing that commit 05f0addd9b ("drm/i915/icl: Enhanced
execution list support") already tried to avoid the save bits
on ICL, but only inside populate_lr_context().
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Testcase: igt/drv_selftest/live_hangcheck/others-priority
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107399
References: 05f0addd9b ("drm/i915/icl: Enhanced execution list support")
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180809235852.24516-1-paulo.r.zanoni@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This will make it easier to test PSR1 on PSR2 capable eDP machines.
Changes since v1:
- Remove I915_PSR_DEBUG_FORCE_PSR2, it did nothing, not sure forcing
PSR2 would even work.
- Handle NULL crtc in intel_psr_set_debugfs_mode. (dhnkrn)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180808141911.7647-2-maarten.lankhorst@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Currently tests modify i915.enable_psr and then do a modeset cycle
to change PSR. We can write a value to i915_edp_psr_debug to force
a certain PSR mode without a modeset.
To retain compatibility with older userspace, we also still allow
the override through the module parameter, and add some tracking
to check whether a debugfs mode is specified.
Changes since v1:
- Rename dev_priv->psr.enabled to .dp, and .hw_configured to .enabled.
- Fix i915_psr_debugfs_mode to match the writes to debugfs.
- Rename __i915_edp_psr_write to intel_psr_set_debugfs_mode, simplify
it and move it to intel_psr.c. This keeps all internals in intel_psr.c
- Perform an interruptible wait for hw completion outside of the psr
lock, instead of being forced to trywait and return -EBUSY.
Changes since v2:
- Rebase on top of intel_psr changes.
Changes since v3:
- Assign psr.dp during init. (dhnkrn)
- Add prepared bool, which should be used instead of relying on psr.dp. (dhnkrn)
- Fix -EDEADLK handling in debugfs. (dhnkrn)
- Clean up waiting for idle in intel_psr_set_debugfs_mode.
- Print PSR mode when trying to enable PSR. (dhnkrn)
- Move changing psr debug setting to i915_edp_psr_debug_set. (dhnkrn)
Changes since v4:
- Return error in _set() function.
- Change flag values to make them easier to remember. (dhnkrn)
- Only assign psr.dp once. (dhnkrn)
- Only set crtc_state->has_psr on the crtc with psr.dp.
- Fix typo. (dhnkrn)
Changes since v5:
- Only wait for PSR idle on the PSR connector correctly. (dhnkrn)
- Reinstate WARN_ON(drrs.dp) in intel_psr_enable. (dhnkrn)
- Remove stray comment. (dhnkrn)
- Be silent in intel_psr_compute_config on wrong connector. (dhnkrn)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180809142101.26155-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
The call to i915_gem_unpark() checks that we hold a rpm wakeref before
taking a long term wakeref for i915->gt.awake. We should therefore make
sure we do hold the wakeref when directly calling unpark to disable
the retire worker.
Fixes: 932cac10c8 ("drm/i915/selftests: Prevent background reaping of active objects")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180809063449.4474-1-chris@chris-wilson.co.uk
On suspend, we cancel the automatic forcewake and clear all other sources
of forcewake so the machine can sleep before we do suspend. However, we
expose the forcewake to userspace (only via debugfs, but nevertheless we
do) and want to restore that upon resume or else our accounting will be
off and we may not acquire the forcewake before we use it. So record
which domains we cleared on suspend and reacquire them early on resume.
v2: Hold the spinlock to appease our sanitychecks
v3: s/fw_domains_user/fw_domains_saved/ to convey intent more clearly
Reported-by: Imre Deak <imre.deak@linux.intel.com>
Fixes: b847305080 ("drm/i915: Fix forcewake active domain tracking")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Imre Deak <imre.deak@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180808210842.3555-1-chris@chris-wilson.co.uk
Now with a more efficacious workaround for the lost interrupts after
reset, we can remove the hack of kicking the waiters after reset. The
issue was that the kick only worked for the immediate window after the
reset (those seqno that would complete in the time it took for the
waiter thread to perform its check) but miss any seqno that lacked an
interrupt afterwards.
References: 39f3be162c ("drm/i915: Kick waiters on resetting legacy rings")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180808105101.913-3-chris@chris-wilson.co.uk
An oddity occurs on Sandybridge, Ivybridge and Haswell (and presumably
Valleyview) in that for the period following the GPU restart after a
reset, there are no GT interrupts received. From Ville's notes, bit 0 in
the HWSTAM corresponds to the render interrupt, and if we unmask it we
do see immediate resumption of GT interrupt delivery (via the master irq
handler) after the reset.
v2: Limit the w/a to the render interrupt from rcs
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107500
Fixes: c549808946 ("drm/i915: Mask everything in ring HWSTAM on gen6+ in ringbuffer mode")
References: d420a50c21 ("drm/i915: Clean up the HWSTAM mess")
Testcase: igt/gem_eio/reset-stress
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180808105101.913-2-chris@chris-wilson.co.uk
Hitting the timeout and finding that all engines are actually idle is
indicative of an interrupt delivery problem. This problem is an issue
that we need to fix, so make sure we log it and provide the GEM trace.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180808105101.913-1-chris@chris-wilson.co.uk
On ICL there are 5 fused power gates, so add the two missing ones for
clarity.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-11-imre.deak@intel.com
There is no need for separate IDs for power wells on a new platform with
the same functionality as an other power well on a previous platform, we
can just reuse the ID from the previous platform. This is only possible
after the previous patches where we removed dependence on the actual
enum values.
This also fixes a problem on ICL where in assert_can_enable_dc5/9() we
would've failed to look up the PW#2 power well.
v2:
- Keep an ID assigned for the ICL PW#2 power well too. (Paulo)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
[Added comment about the ICL PW#2 fix to the commit log]
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-10-imre.deak@intel.com
The format for the ID names is <platform>_DISP_PW_* so rename the IDs
not following this accordingly. Leave BXT_DPIO_CMN_BC as-is since we'll
change that to use another existing ID in the next patch.
v2:
- Fix line over 80 chars checkpatch warning.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-9-imre.deak@intel.com
Now that we removed dependence on the power well IDs to determine the
control register and request/status flag offsets the only purpose of
power well IDs is to look up power wells directly bypassing the power
domains framework. However this direct lookup isn't needed for most of
the exisiting power wells and hopefully won't be needed for any new
power wells in the future. To make maintenance of the power well ID enum
easier, don't require a unique ID for each power well, only if it's
necessary. Remove the IDs becoming redundant this way and assign to all
the corresponding power wells a new DISP_PW_ID_NONE ID.
After the previous two patches the IDs don't need to have a fixed value,
so remove the explicit initializers and adjust the enum's code comment
accordingly.
v2:
- Keep required ID assignments for HSW_DISP_PW_GLOBAL and ICL_DISP_PW_2.
(Paulo)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-8-imre.deak@intel.com
Similarly to the previous patch use a separate request/status HW flag
index defined right after the corresponding control registers instead of
depending for this on the power well IDs. Since the set of
control/status registers varies among the different power wells (on a
single platform), also add a new i915_power_well_registers struct that
we populate and assign to each DDI power well as needed.
Also clarify a bit the code comment describing the function and layout
of the control registers.
This also fixes a problem on ICL, where we incorrectly read the KVMR
control register in hsw_power_well_requesters() even for DDI and AUX
power wells.
v2:
- Clarify platform range tags in code comments. (Paulo)
- Fix line over 80 chars checkpatch warning.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-7-imre.deak@intel.com
Atm, we determine the control/status flag offsets within the PUNIT
control/status registers based on the power well's ID. Since the power
well ID enum is global across all platforms, the associated macros to
get the flag offsets involves some magic. This makes checking the
register/bit definitions against the specification more difficult than
necessary. Also the values in the power well ID enum must stay fixed,
making code maintenance of the enum cumbersome.
To solve the above define the control/status flag indices right after
the corresponding registers and use these to derive the control/status
flag values by storing the indices in the i915_power_well_desc struct.
Initializing anonymous union fields require the preceding field in the
struct to be explicitly initialized - even when using named
initializers - and the initialization to be done right before the union
initialization, hence the reordering of the .id fields.
v2:
- Clarify commit log message about anonymous union initializers. (Paulo)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-6-imre.deak@intel.com
It makes sense to keep unchanging data const. Extract such fields from
the i915_power_well struct into a new i915_power_well_desc struct that
we initialize during compile time. For the rest of the dynamic
fields allocate an array of i915_power_well objects in i915 dev_priv,
and link to each of these objects their corresponding
i915_power_well_desc object.
v2:
- Fix checkpatch warnings about missing param name in fn declaration and
lines over 80 chars. (Paulo)
- Move check for unique IDs to __set_power_wells().
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
[Fixed checkpatch warn in __set_power_wells()]
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-5-imre.deak@intel.com
The callbacks these asserts are called from are used from a single power
well, so not much point in checking that. The check also requires a unique
power well ID that we would need to keep around only for this purpose.
(A follow-up patch removes power well IDs not needed for direct power
well access).
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-4-imre.deak@intel.com
intel_power_domains_fini() rolls back what was done in
intel_power_domains_init_hw(), so rename and move it accordingly. This
allows us adding a cleanup function later for intel_power_domains_init()
in a cleaner way.
No functional change.
v2:
- Fix checkpatch error adding missing param name to function
declaration. (Paulo)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-3-imre.deak@intel.com
Similarly to commit 0a445945be
("drm/i915: Work around GCC anonymous union initialization bug")
we need to initialize anonymous unions inside extra braces to work
around a GCC4.4 build error.
v2:
- Fix checkpatch errors in commit log. (Paulo)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-2-imre.deak@intel.com
We have a few instances of checking seqno-1 to see if the HW has started
the request. Pull those together under a helper.
v2: Pull the !seqno assertion higher, as given seqno==1 we may indeed
check to see if we have started using seqno==0.
Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806112605.20725-1-chris@chris-wilson.co.uk
We distribute DDB equally among all pipes irrespective of display
buffer requirement of each pipe. This leads to a situation where high
resolution y-tiled display can not be enabled with 2 low resolution
displays.
Main contributing factor for DDB requirement is width of the display.
This patch make changes to distribute ddb based on display width.
So display with higher width will get bigger chunk of DDB.
Changes Since V1:
- pipe_size/ddb_size will not overflow u16 so use appropriate
data-types during computation (Chris)
Changes Since V2:
- avoid redundancy and possible truncation errors (Chris)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107113
Cc: raviraj.p.sitaram@intel.com
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180801151113.5337-1-mahesh1.kumar@intel.com
ddb_size is u16 so use same return type for intel_get_ddb_size
wrapper.
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180731142445.30723-2-mahesh1.kumar@intel.com
The dma_mapping_error() returns true on error but we want to return
-ENOMEM here.
Fixes: 79e542f5af ("drm/i915/kvmgt: Support setting dma map for huge pages")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
To consolidate all gvt private MMIO definition in one place,
this moves some not yet used in i915 to reg.h.
Reviewed-by: Hang Yuan <hang.yuan@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Caught by W=1 to fix left wrong function comment doc.
Reviewed-by: Hang Yuan <hang.yuan@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Make kvmgt_dma_map/unmap_guest_page as static function.
Reviewed-by: Hang Yuan <hang.yuan@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Experience teaches us over and over again that coherency on Baytrail
requires the odd heavy hammer, and in particular clflush alone is not
enough to guarrantee that writes from the CPU are picked up by the CS.
Do as we do elsewhere and ensure we have an unconditional
i915_gem_chipset_flush() after writing to memory and submitting a batch
to HW.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107499
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806144604.8346-1-chris@chris-wilson.co.uk
gvt_pin_guest_page extracted some of the gvt_dma_map_page functionality:
commit 79e542f5af ("drm/i915/kvmgt: Support setting dma map for huge pages")
And yet, part of it was reintroduced in:
commit 39b4cbadb9 ("drm/i915/kvmgt: Check the pfn got from vfio_pin_pages")
Causing kvmgt part to no longer build. Let's remove it.
Reported-by: Tomasz Lis <tomasz.lis@intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Changbin Du <changbin.du@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712155330.32055-1-michal.winiarski@intel.com
(cherry picked from commit 4eaf317a60)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The LPE audio is a child device of i915, it is powered up and down
alongside the igfx and presents no independent runtime interface. This
aptly fulfils the description of a "No-Callback" Device, so mark it
thus.
Fixes: 183c00350c ("drm/i915: Fix runtime PM for LPE audio")
Testcase: igt/pm_rpm/basic-pci-d3-state
Testcase: igt/pm_rpm/basic-rte
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180802140416.6062-1-chris@chris-wilson.co.uk
(cherry picked from commit 46e831abe8)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The register for 0xe420 is unable to hold any value, including
this bit. The documentation is also mixed between having a
register bit for toggle and having a state command setup
for it. Apparently the register toggle is deprecated.
Remove the register toggle as evidence shows it's futile.
The thing remaining is an apology and humble request for
Mesa folks to resurrect their state setup for this as they
were on right track from start.
This reverts commit 0bf059f353.
Fixes: 0bf059f353 ("drm/i915/icl: WaEnableFloatBlendOptimization")
References: HSDES#1406393558
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Anuj Phogat <anuj.phogat@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180730120636.26958-1-mika.kuoppala@linux.intel.com
(cherry picked from commit c358514ba8)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
RPS provides a feedback loop where we use the load during the previous
evaluation interval to decide whether to up or down clock the GPU
frequency. Our responsiveness is split into 3 regimes, a high and low
plateau with the intent to keep the gpu clocked high to cover occasional
stalls under high load, and low despite occasional glitches under steady
low load, and inbetween. However, we run into situations like kodi where
we want to stay at low power (video decoding is done efficiently
inside the fixed function HW and doesn't need high clocks even for high
bitrate streams), but just occasionally the pipeline is more complex
than a video decode and we need a smidgen of extra GPU power to present
on time. In the high power regime, we sample at sub frame intervals with
a bias to upclocking, and conversely at low power we sample over a few
frames worth to provide what we consider to be the right levels of
responsiveness respectively. At low power, we more or less expect to be
kicked out to high power at the start of a busy sequence by waitboosting.
Prior to commit e9af4ea2b9 ("drm/i915: Avoid waitboosting on the active
request") whenever we missed the frame or stalled, we would immediate go
full throttle and upclock the GPU to max. But in commit e9af4ea2b9, we
relaxed the waitboosting to only apply if the pipeline was deep to avoid
over-committing resources for a near miss. Sadly though, a near miss is
still a miss, and perceptible as jitter in the frame delivery.
To try and prevent the near miss before having to resort to boosting
after the fact, we use the pageflip queue as an indication that we are
in an "interactive" regime and so should sample the load more frequently
to provide power before the frame misses it vblank. This will make us
more favorable to providing a small power increase (one or two bins) as
required rather than going all the way to maximum and then having to
work back down again. (We still keep the waitboosting mechanism around
just in case a dramatic change in system load requires urgent uplocking,
faster than we can provide in a few evaluation intervals.)
v2: Reduce rps_set_interactive to a boolean parameter to avoid the
confusion of what if they wanted a new power mode after pinning to a
different mode (which to choose?)
v3: Only reprogram RPS while the GT is awake, it will be set when we
wake the GT, and while off warns about being used outside of rpm.
v4: Fix deferred application of interactive mode
v5: s/state/interactive/
v6: Group the mutex with its principle in a substruct
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107111
Fixes: e9af4ea2b9 ("drm/i915: Avoid waitboosting on the active request")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180731132629.3381-1-chris@chris-wilson.co.uk
(cherry picked from commit 60548c554b)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
First of all don't try to read dpcd if PSR is not even supported.
But also, if read failed return -EIO instead of reporting via a
backchannel.
v2: fix dev_priv: At this level m->private is the connector. (CI/DK)
don't convert dpcd read errors to EIO. (DK)
Fixes: 5b7b30864d ("drm/i915/psr: Split sink status into a separate debugfs node")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180720003155.16290-1-rodrigo.vivi@intel.com
(cherry picked from commit 7a72c78bdd)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
A long time ago, we were afraid of handling interrupts and signaling
waiters during a reset, worrying that the confusion in request handling
would interfere with our attempts to process the reset in an orderly
fashion. Since then, we have isolated our irq-driven request handling by
virtue of the engine->timeline.lock and control of kthreads where
required, eliminating the danger of concurrently processing interrupts.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806145647.13131-1-chris@chris-wilson.co.uk
After disabling resource streamer on ICL (due to it actually not
existing there), I got feedback that there have been some experimental
patches for mesa to use RS years ago, but nothing ever landed or shipped
because there was no performance improvement.
This removes it from kernel keeping the uapi defines around for
compatibility.
v2: - re-add the inadvertent removal of CTX_CTRL_INHIBIT_SYN_CTX_SWITCH
- don't bother trying to document removed params on uapi header:
applications should know that from the query.
(from Chris)
v3: - disable CTX_CTRL_RS_CTX_ENABLE istead of removing it
- reword commit message after Daniele confirmed no performance
regression on his machine
- reword commit message to make clear RS is being removed due to
never been used
v4: - move I915_EXEC_RESOURCE_STREAMER to __I915_EXEC_ILLEGAL_FLAGS so
the check on ioctl() is made much earlier by
i915_gem_check_execbuffer() (suggested by Tvrtko)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180803232443.17193-1-lucas.demarchi@intel.com
The next patch in this series will have to make the definition of
irq_cpustat_t available to entering_irq().
Inclusion of asm/hardirq.h into asm/apic.h would cause circular header
dependencies like
asm/smp.h
asm/apic.h
asm/hardirq.h
linux/irq.h
linux/topology.h
linux/smp.h
asm/smp.h
or
linux/gfp.h
linux/mmzone.h
asm/mmzone.h
asm/mmzone_64.h
asm/smp.h
asm/apic.h
asm/hardirq.h
linux/irq.h
linux/irqdesc.h
linux/kobject.h
linux/sysfs.h
linux/kernfs.h
linux/idr.h
linux/gfp.h
and others.
This causes compilation errors because of the header guards becoming
effective in the second inclusion: symbols/macros that had been defined
before wouldn't be available to intermediate headers in the #include chain
anymore.
A possible workaround would be to move the definition of irq_cpustat_t
into its own header and include that from both, asm/hardirq.h and
asm/apic.h.
However, this wouldn't solve the real problem, namely asm/harirq.h
unnecessarily pulling in all the linux/irq.h cruft: nothing in
asm/hardirq.h itself requires it. Also, note that there are some other
archs, like e.g. arm64, which don't have that #include in their
asm/hardirq.h.
Remove the linux/irq.h #include from x86' asm/hardirq.h.
Fix resulting compilation errors by adding appropriate #includes to *.c
files as needed.
Note that some of these *.c files could be cleaned up a bit wrt. to their
set of #includes, but that should better be done from separate patches, if
at all.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make sure that the RPS IIR is completely clear on disabling so we should
not get any more interrupts after idling. Since the IIR is shared with
the guc, we have to be careful to only clobber RPS events.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180802100631.31305-3-chris@chris-wilson.co.uk
The LPE audio is a child device of i915, it is powered up and down
alongside the igfx and presents no independent runtime interface. This
aptly fulfils the description of a "No-Callback" Device, so mark it
thus.
Fixes: 183c00350c ("drm/i915: Fix runtime PM for LPE audio")
Testcase: igt/pm_rpm/basic-pci-d3-state
Testcase: igt/pm_rpm/basic-rte
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180802140416.6062-1-chris@chris-wilson.co.uk
We don't have proper watermark NV12 support on ICL due to differences
in how it should be implemented. In commit 234059da0f
("drm/i915/icl: NV12 y-plane ddb is not in same plane") we avoided
writing the non-existent PLANE_NV12_BUF_CFG registers but we forgot to
also avoid them on the hardware state readout. While the code is still
not correct, at least now we can avoid unclaimed register error
messages when dealing with RGB formats, which makes CI happier.
Also add some FIXME comments in order to make it even more clear that
there's still work to do.
References: commit 234059da0f ("drm/i915/icl: NV12 y-plane ddb is
not in same plane")
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180801004614.22149-1-paulo.r.zanoni@intel.com
We used to reset last_adj to 0 on crossing a power domain boundary, to
slow down our rate of change. However, commit 60548c554b ("drm/i915:
Interactive RPS mode") accidentally caused it to be reset on every
frequency update, nerfing the fast response granted by the slow start
algorithm.
Fixes: 60548c554b ("drm/i915: Interactive RPS mode")
Testcase: igt/pm_rps/mix-max-config-loaded
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180802100631.31305-1-chris@chris-wilson.co.uk
if a context is a restore inhibit context, gfx hw only load the first page
for ring context, so we only need to copy from guest the 1 page too.
v3: use "return" instead of "goto" for inhibit case. (zhenyu wang)
v2: move judgement of restore inhibit to a macro in mmio_context.h
Signed-off-by: Zhao Yan <yan.y.zhao@intel.com>
Acked-by: Hang Yuan <hang.yuan@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
MI_NOOP is a common command appearing in almost all command buffers, put it
into a fastpath can improve perfomance, especially in command buffers
contains lots of MI_NOOPs (0s).
Take glmark2 as an example, 3% performance increase is observed after
introduced this patch. Meanwhile, in case where abundant in MI_NOOPs,
up to 12% performance increase is measured.
v2: use lowercase for index of MI_NOOP in cmd_info (zhenyu wang)
Signed-off-by: Li Weinan <weinan.z.li@intel.com>
Signed-off-by: Zhao Yan <yan.y.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
In the aub trace utility, the context images are terminated with a
MI_BATCH_BUFFER_END; the simulator is reported as complaining otherwise.
Do the same for our protocontext image for completeness, and in passing
apply the magic bit for gen10 to mark the end of the context image.
Reported-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180730164325.12770-1-chris@chris-wilson.co.uk
The register for 0xe420 is unable to hold any value, including
this bit. The documentation is also mixed between having a
register bit for toggle and having a state command setup
for it. Apparently the register toggle is deprecated.
Remove the register toggle as evidence shows it's futile.
The thing remaining is an apology and humble request for
Mesa folks to resurrect their state setup for this as they
were on right track from start.
This reverts commit 0bf059f353.
Fixes: 0bf059f353 ("drm/i915/icl: WaEnableFloatBlendOptimization")
References: HSDES#1406393558
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Anuj Phogat <anuj.phogat@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180730120636.26958-1-mika.kuoppala@linux.intel.com
A bit larger this time around, due to introduction of "dpu1" support
for the display controller in sdm845 and beyond. This has been on
list and undergoing refactoring since Feb (going from ~110kloc to
~30kloc), and all my review complaints have been addressed, so I'd be
happy to see this upstream so further feature work can procede on top
of upstream.
Also includes the gpu coredump support, which should be useful for
debugging gpu crashes. And various other misc fixes and such.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGv-8y3zguY0Mj1vh=o+vrv_bJ8AwZ96wBXYPvMeQT2XcA@mail.gmail.com
RPS provides a feedback loop where we use the load during the previous
evaluation interval to decide whether to up or down clock the GPU
frequency. Our responsiveness is split into 3 regimes, a high and low
plateau with the intent to keep the gpu clocked high to cover occasional
stalls under high load, and low despite occasional glitches under steady
low load, and inbetween. However, we run into situations like kodi where
we want to stay at low power (video decoding is done efficiently
inside the fixed function HW and doesn't need high clocks even for high
bitrate streams), but just occasionally the pipeline is more complex
than a video decode and we need a smidgen of extra GPU power to present
on time. In the high power regime, we sample at sub frame intervals with
a bias to upclocking, and conversely at low power we sample over a few
frames worth to provide what we consider to be the right levels of
responsiveness respectively. At low power, we more or less expect to be
kicked out to high power at the start of a busy sequence by waitboosting.
Prior to commit e9af4ea2b9 ("drm/i915: Avoid waitboosting on the active
request") whenever we missed the frame or stalled, we would immediate go
full throttle and upclock the GPU to max. But in commit e9af4ea2b9, we
relaxed the waitboosting to only apply if the pipeline was deep to avoid
over-committing resources for a near miss. Sadly though, a near miss is
still a miss, and perceptible as jitter in the frame delivery.
To try and prevent the near miss before having to resort to boosting
after the fact, we use the pageflip queue as an indication that we are
in an "interactive" regime and so should sample the load more frequently
to provide power before the frame misses it vblank. This will make us
more favorable to providing a small power increase (one or two bins) as
required rather than going all the way to maximum and then having to
work back down again. (We still keep the waitboosting mechanism around
just in case a dramatic change in system load requires urgent uplocking,
faster than we can provide in a few evaluation intervals.)
v2: Reduce rps_set_interactive to a boolean parameter to avoid the
confusion of what if they wanted a new power mode after pinning to a
different mode (which to choose?)
v3: Only reprogram RPS while the GT is awake, it will be set when we
wake the GT, and while off warns about being used outside of rpm.
v4: Fix deferred application of interactive mode
v5: s/state/interactive/
v6: Group the mutex with its principle in a substruct
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107111
Fixes: e9af4ea2b9 ("drm/i915: Avoid waitboosting on the active request")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180731132629.3381-1-chris@chris-wilson.co.uk
Entries will either be pointing to scratch or real PD, making the
px_page(pd) check pointless. Also since there are no other users of
px_page, just remove it.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180730120544.20784-1-matthew.auld@intel.com
The i915 DRM driver very cleverly used ascii85 encoding for their
GPU state file. Move the encode functions to a general header file to
support other drivers that might be interested in the same
functionality.
v4: Make the return value const char * as suggested by Chris Wilson
v3: Fix error_puts -> err_puts pointed out by the 01.org bot
v2: Update API to be cleaner for the caller as suggested by Chris Wilson
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We occasionally see that the clflush prior to a read of GPU data is
returning stale data, reminiscent of much earlier bugs fixed by adding a
second clflush for serialisation. As drm_clflush_virt_range() already
supplies the workaround, use it rather than open code the clflush
instruction.
References: 396f5d62d1 ("drm: Restore double clflush on the last partial cacheline")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180730075351.15569-3-chris@chris-wilson.co.uk
According to intel_read_wm_latency() it is perfectly legal for one WM
and all subsequent levels to be 0 (and the deeper powersaving states
disabled), so don't shout *ERROR*, over and over again.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180726161527.10516-1-chris@chris-wilson.co.uk
For a TBT sequence, we need to set the IO type to TBT
in DDI_AUX_CTL.
v2: Avoid duplications.(Paulo)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1532648115-29795-2-git-send-email-anusha.srivatsa@intel.com
Add missing TBT check in the Pll calculation.
v2: do not use a auxiliary function to check if status is
TBT or not. (Paulo)
v3: Code style changes. (Paulo)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1532648115-29795-1-git-send-email-anusha.srivatsa@intel.com
While things may have been different before, right now the function is
very simple and has a single caller. IMHO any possible benefits from
an abstraction here are gone and not worth the price of the current
indirection while reading the code.
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180607230700.28359-1-paulo.r.zanoni@intel.com
The new recommendation from the spec is to simply not set this bit
anymore. Not setting the bit would prevent some hangs that our driver
manages to avoid since commit c8af5274c3 ("drm/i915: enable the
pipe/transcoder/planes later on HSW+"), and the theoretical downside
of not setting the bit doesn't seem realistic according to the HW
team. Let's follow their recommendation.
BSpec: 20233
References: commit c8af5274c3 ("drm/i915: enable the
pipe/transcoder/planes later on HSW+")
Cc: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180726001229.13791-1-paulo.r.zanoni@intel.com
Add a fault injection point in the WOPCM initialization path.
v4:
Move the injection inside the WOPCM init function.
Signed-off-by: Jakub Bartmiński <jakub.bartminski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180727141148.30874-5-jakub.bartminski@intel.com
Since ggtt_offset_bias is now stored in ggtt.pin_bias, it is duplicated
inside i915_gem_context, and can instead be accessed directly from ggtt.
v3:
Added a helper function to retrieve the ggtt.pin_bias from the vma.
v4:
Moved the helper function to the previous patch in the series.
Dropped the bias from intel_ring_pin. This introduces a slight functional
change since we are always pinning the ring a bit higher if GuC is present
even though we don't really need to.
v8:
Fixed patch not applying on the most recent upstream.
Signed-off-by: Jakub Bartmiński <jakub.bartminski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180727141148.30874-4-jakub.bartminski@intel.com
Removing the pin bias from GuC allows us to not check for GuC every time
we pin a context, which fixes the assertion error on unresolved GuC
platform default in mock contexts selftest.
It also seems that we were using uninitialized WOPCM variables when
setting the GuC pin bias. The pin bias has to be set after the WOPCM,
but before the call to i915_gem_contexts_init where the first contexts
are pinned.
v2:
This also makes it so that there's no need to set GuC variables from
within the WOPCM init function or to move the WOPCM init, while keeping
the correct initialization order. Also for mock tests the pin bias is
left at 0 and we make sure that the pin bias with GuC will not be
smaller than without GuC.
v3:
Avoid unused i915 in intel_guc_ggtt_offset if debug is disabled.
v4:
Squash with WOPCM init reordering.
Moved the i915_ggtt_pin_bias helper to this patch, and made some
functions use it instead of directly dereferencing i915->ggtt.
v5:
Since we now don't use wopcm.guc.base for the pin bias there's no need to
validate it. It also has already been verified in WOPCM init.
v6:
Deleted the now unnecessarily introduced includes from previous versions.
Dropped naming changes from dev_priv to i915 for better patch readability.
v7:
Changed some comments to make more sense in the context they're in.
v8:
Moved and renamed the function which now returns the wopcm.guc.size to
intel_guc.c:intel_guc_reserved_gtt_size to avoid any possible confusion
with the pin_bias in ggtt, which should be used for pinning.
Fixed patch not applying or the most recent upstream.
Fixes: f7dc0157e4 ("drm/i915/uc: Fetch GuC/HuC firmwares from guc/huc specific init")
Testcase: igt/drv_selftest/mock_contexts #GuC
Signed-off-by: Jakub Bartmiński <jakub.bartminski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180727141148.30874-3-jakub.bartminski@intel.com
There seems to be no reason for doing extra work on WOPCM partitioning
in the case GuC is not used, as the partitioning will not be used by the
intel_wopcm_init_hw function anyway.
Signed-off-by: Jakub Bartmiński <jakub.bartminski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180727141148.30874-2-jakub.bartminski@intel.com
It would appear that the calculated GuC pin bias was larger than it should
be, as the GuC address space does NOT contain the "HW contexts RSVD" part
of the WOPCM. Thus, the GuC pin bias is simply the GuC WOPCM size.
v5:
Clarify the diagram to better represent the GuC address space.
Since we now don't use guc.base for the pin bias there's no need to
validate it. It also has already been verified in WOPCM init.
Bspec: 1180
Signed-off-by: Jakub Bartmiński <jakub.bartminski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180727141148.30874-1-jakub.bartminski@intel.com
As GEN8_LR_CONTEXT_ALIGN is I915_GTT_MIN_ALIGNMENT is it functionally
equivalent to 0, and we will not be able to reduce the min-alignment for
the GTT, so passing 0 is and will remain equivalent.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180727092947.1953-1-chris@chris-wilson.co.uk
Using PAGE_SIZE for virtual offset alignment is superfluous as it is
equal to the minimum gtt alignment and so equivalent to 0. It is also
the wrong value to use as we stopped using physical page constructs for
the virtual GTT, i.e. it would be preferrable to use I915_GTT_PAGE_SIZE
and in these cases merely imply I915_GTT_MIN_ALIGNMENT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180727091855.1879-1-chris@chris-wilson.co.uk
Immutable Branch which moves the cros_ec_i2c and cros_ec_spi
transport drivers from mfd to platform/chrome. Changes in arm are a simple
rename in defconfigs. Change in input is a rename in help text.
-----BEGIN PGP SIGNATURE-----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=EhHj
-----END PGP SIGNATURE-----
Merge branches 'ib-mfd-4.19', 'ib-mfd-gpio-pinctrl-4.19', 'ib-mfd-i915-media-platform-4.19' and 'ib-mfd-regulator-4.19', tag 'ib-platform-chrome-mfd-move-cros-ec-transport-for-4.19' into ibs-for-mfd-merged
Immutable branch (mfd, chrome) due for the v4.19 window
Immutable Branch which moves the cros_ec_i2c and cros_ec_spi
transport drivers from mfd to platform/chrome. Changes in arm are a simple
rename in defconfigs. Change in input is a rename in help text.
On older HW, gen2/3, fence registers are used for detiling GPU commands
and as such changing those registers requires serialisation with the
requests on the GPU. Anything running on the GPU is subject to a hang,
and so we must be able to recover cleanly in the middle of a stuck wait
on a fence register.
We can simulate using the fence on the GPU simply by marking the fence
as active on the request for this vma, the interface being common to all
gen, thus broadening the test.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180719194746.19111-2-chris@chris-wilson.co.uk
To test eviction from a ppgtt, we just want a ppgtt i.e. something other
than the Global GTT which is shared and used by the kernel for HW
features like fencing and scanout. However, we also need it to pass
!i915_is_ggtt() and the simplest way is to emulate a full user context
rather than the internal kernel context that is used for the GGTT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180719194746.19111-1-chris@chris-wilson.co.uk
If we issue a device level GPU reset on the older gen, it will disable
key components of the GMCH and the display engine. The purpose of
wedging is to simply prevent further GEM usage without disabling KMS, so
we need to be careful when we do issue the reset on wedging.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180726085033.4044-3-chris@chris-wilson.co.uk
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
If we fail during GEM initialisation, we scrub the HW state by
performing a device level GPU resuet. However, we want to leave the
system in a usable state (with functioning KMS but no GEM) so after
scrubbing the HW state, we need to restore some sane defaults and
re-enable the low-level common parts of the GPU (such as the GMCH).
v2: Restore GTT entries.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180726085033.4044-2-chris@chris-wilson.co.uk
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
i915_gem_tile_height() asserts that the object is tiled, but inside the
error printer for the selftest we computed the row size regardless of
tiling, tripping over the assert.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180726104759.8684-1-chris@chris-wilson.co.uk
We are too late in the enabling sequence to back out cleanly, not updating
state tracking variables, like intel_dp->active_mst_links in this
instance, results in incorrect behaviour further along.
v2: Fixed int v/s bool comparison
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107281
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Tested-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180718171943.3246-2-dhinakaran.pandiyan@intel.com
The short pulse handler checks if channel equalization is okay and
goes onto retrain a link if there are active MST links. This retraining
path is not meant for new MST connections, but due to a bug elsewhere, if
active_mst_links is < 0 the boolean check for active_mst_links passes and
we proceed to retrain a new link. This results in a sequence of failed link
training attempts, most likely due to the hardware not setup for link
training at that point i.e., missing the DDI pre_enable sequence.
[ 80.301272] [drm:intel_dp_check_mst_status] channel EQ not ok, retraining
[ 80.301312] [drm:intel_ddi_prepare_link_retrain] *ERROR* Timeout waiting for DDI BUF C idle bit
The above error gives us a hint something went wrong before link
training started.
Check for a positive value of active_mst_links and throw in a warning for
invalid active_mst_links as debug aid.
Cc: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Tested-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180718171943.3246-1-dhinakaran.pandiyan@intel.com
On GLK NUC platforms the HDMI retiming buffer needs additional disabled
time to correctly sync to a faster incoming signal.
When measured on a scope the highspeed lines of the HDMI clock turn off
for ~400uS during a normal resolution change. The HDMI retimer on the
GLK NUC appears to require at least a full frame of quiet time before a
new faster clock can be correctly sync'd. Wait 100ms due to msleep
inaccuracies while waiting for a completed frame. Add a quirk to the
driver for GLK boards that use ITE66317 HDMI retimers.
V2: Add more devices to the quirk list
V3: Delay increased to 100ms, check to confirm crtc type is HDMI.
V4: crtc type check extended to include _DDI and whitespace fixes
v5: Fix white spaces, remove the macro for delay. Revert the crtc type
check introduced in v4.
Cc: Imre Deak <imre.deak@intel.com>
Cc: <stable@vger.kernel.org> # v4.14+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105887
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Tested-by: Daniel Scheller <d.scheller.oss@gmail.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710200205.1478-1-radhakrishna.sripada@intel.com
(cherry picked from commit 90c3e21987)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The Gen11 TypeC PHY DDI Buffer chapter, PHY Clock Gating Programming
section says that PHY clock gating should be disabled before starting
voltage swing programming, then enabled after any link training is
complete.
v2: Simple rebase.
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725002813.6938-6-paulo.r.zanoni@intel.com
Programming this register is part of the Enable Sequence for
DisplayPort on ICL. Do as the spec says.
v2: Simple rebase.
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725002813.6938-5-paulo.r.zanoni@intel.com
In ICL, Flexible IO Adapter (FIA) muxes data and clocks of USB 3.1,
tbt and display controller. In DP alt mode FIA configure the
number of lanes and will be used apart from DPCD read to calculate max
available lanes for DP enablement.
v2 (from Paulo): Simple rebase.
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com> (v1).
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
[Paulo: significant rewrite of the patch.]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725002813.6938-4-paulo.r.zanoni@intel.com
The type is detected based on the live status bits. Once detected,
it's not supposed to be changed, so we have some sanity checks for
that.
v2: Rebase.
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725002813.6938-3-paulo.r.zanoni@intel.com
Do like the other functions and check for the status bits. The "Hot
Plug Detection" page from our documentation says we can't just use the
ISR bits on the CPU side (North Display, which has the TC and TBT
modes), so use the correct register: DFLEXDPSP, TC Live State field.
v2: Rebase.
v3:
- Simplify true/false assignment (Rodrigo).
- Reorganize is_gen if ladder (Rodrigo).
- Don't use the ISR for TC/TBT CPU bits.
v4:
- Improve commit message wording (Lucas).
v5:
- COMMIT_LOG_LONG_LINE (Checkpatch).
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> (v3).
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725195927.12059-1-paulo.r.zanoni@intel.com
Clarifies the clock recovery loop limit comment that 80
max_cr_tries for pre-DP1.4 devices was chosen as a very
tolerant upper bound.
Assumptions made:
- DP1.4 syncs should be smarter so they won't need more
than 10 tries
- pre-DP1.4 syncs should be compliant enough to not need
that many tries (80) but we should tolerate any that may
trigger this corner case
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Marc Herbert <marc.herbert@intel.com>
Suggested-by: Marc Herbert <marc.herbert@intel.com>
Signed-off-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Reviewed-by: Marc Herbert <marc.herbert@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1532471612-30001-1-git-send-email-nathan.d.ciobanu@linux.intel.com
This sequence is used to setup voltage swing before enabling MG PHY DDI
as well as for changing the voltage during DisplayPort Link training.
For ICL, there are two types of DDIs. This sequence needs to be used
for MG PHY DDI which is ports C-F.
v6 (From Manasi):
* Add programming for MG_CLKHUB and MG_TX_DCC as per the
spec updates
v5 (from Paulo):
* Checkpatch.
v4 (from Paulo):
* Fix bogus error message
* Fix copy+paste bugs (missing s/TX1/TX2/ after copy+paste)
* Use the new mask names
* Stay under 80 columns
* Add some blank lines
v3:
* Clear the regs before writing (Paulo)
v2:
* Rename to MG PHY in the function def (Jani Nikula)
* Rebase on top of new revision of other patches in series
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530225344-20373-2-git-send-email-manasi.d.navare@intel.com
This patch adds the remaining register definitions and bit fields
required for MG PHy DDI buffer initializations and voltage
swing programming for MG PHy DDI ports.
While at it this patch also fixes the naming for previously defined
MG PHY registers in original commit id (c92f47b5ec "drm/i915/icl:
Add register defs for voltage swing sequences for MG PHY DDI").
Since the MG PHY registers are first defined in ICL platform, there
is no need for _ICL prefix.
v4 (from Paulo): add two white spaces to CRI_CALCINIT too.
v3:
* Fix register names, add spaces for MASK defines, correct the order
of #defines (Paulo)
v2:
* Change the MG_TX_DRVCTL registers names to match the spec (Anusha)
Cc: James Ausmus <james.ausmus@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1531510993-6606-1-git-send-email-manasi.d.navare@intel.com
On Sandybridge, we need a workaround to wait for the CPU thread to wake
up before we are sure that we have enabled the GT power well. However,
we do see the errors being reported and failed reads returning spurious
results. To try and capture more details as it fails, promote the error
into a WARN so we grab the stacktrace, and to try and reduce the
frequency of error increase the timeout from 500us to 5ms.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180720111102.11549-1-chris@chris-wilson.co.uk
A reasonably common operation is to pin the map of the vma alongside the
vma itself for the lifetime of the vma, and so release both pins at the
same time as destroying the vma. It is common enough to pull into the
release function, making that central function more attractive to a
couple of other callsites.
The continual ulterior motive is to sweep over errors on module load
aborting...
Testcase: igt/drv_module_reload/basic-reload-inject
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180721125037.20127-1-chris@chris-wilson.co.uk
Changes the type and renames the max_vswing_tries variable
which was declared as an integer but used as a boolean
making it easy to be confused with a counter.
Changes in v2:
- updated the title and commit message
- left the loop exit point in place
v3: fix typo in title
v4: renamed max_vswing to max_vswing_reached (Ville)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Marc Herbert <marc.herbert@intel.com>
Signed-off-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180720214413.29506-2-rodrigo.vivi@intel.com
Limit the link training clock recovery loop to 10 attempts at
LANEx_CR_DONE per DP 1.4 spec section 3.5.1.2.2 and 80 attempts for
pre-DP 1.4 (4 voltage levels x 4 preemphasis levels x
x 5 identical voltages tries). Some faulty USB-C MST hubs can
cause us to get stuck in this loop indefinitely requesting something
like:
voltage swing: 0, pre-emphasis level: 2
voltage swing: 1, pre-emphasis level: 2
voltage swing: 0, pre-emphasis level: 3
over and over so max_vswing would never be reached,
drm_dp_clock_recovery_ok() would never return true and voltage_tries
would always get reset to 1. The driver sends those values to the hub
but the hub keeps requesting new values every time.
Changes in v2:
- updated commit message (DK, Manasi)
- defined DP_DP14_MAX_CR_TRIES (Marc)
- made the loop iterate for max 10 times (Rodrigo, Marc)
Changes in v3:
- changed error message to use DP_DP14_MAX_CR_TRIES
Changes in v4:
- Updated the title to reflect the change
- Updated the commit message
- Added 80 attempts for pre-DP 1.4 devices
Changes in v5:
- Removed DP_DP14_MAX_CR_TRIES from drm
v6: Updated comment to match kernel style (Rodrigo)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Marc Herbert <marc.herbert@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180720214413.29506-1-rodrigo.vivi@intel.com
gvt_pin_guest_page extracted some of the gvt_dma_map_page functionality:
commit 79e542f5af ("drm/i915/kvmgt: Support setting dma map for huge pages")
And yet, part of it was reintroduced in:
commit 39b4cbadb9 ("drm/i915/kvmgt: Check the pfn got from vfio_pin_pages")
Causing kvmgt part to no longer build. Let's remove it.
Reported-by: Tomasz Lis <tomasz.lis@intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Changbin Du <changbin.du@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712155330.32055-1-michal.winiarski@intel.com
We need a backmerge to get DP_DPCD_REV_14 before we push other
i915 changes to dinq that could break compilation.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
First of all don't try to read dpcd if PSR is not even supported.
But also, if read failed return -EIO instead of reporting via a
backchannel.
v2: fix dev_priv: At this level m->private is the connector. (CI/DK)
don't convert dpcd read errors to EIO. (DK)
Fixes: 5b7b30864d ("drm/i915/psr: Split sink status into a separate debugfs node")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180720003155.16290-1-rodrigo.vivi@intel.com
Just a small clean-up with no functional change, only
removing a variable that is never actually used.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: <nathan.d.ciobanu@linux.intel.com>
Reviewed-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180719234217.7855-1-rodrigo.vivi@intel.com
Not all chipsets have an internal buffer delaying the visibility of
writes via the GGTT being visible by other physical paths, but we use a
very heavy workaround for all. We only need to apply that workarounds to
the chipsets we know suffer from the delay and the resulting coherency
issue.
Similarly, the same inconsistent coherency fouls up our ABI promise that
a write into a mmap_gtt is immediately visible to others. Since the HW
has made that a lie, let userspace know when that contract is broken.
(Not that userspace would want to use mmap_gtt on those chipsets for
other performance reasons...)
Testcase: igt/drv_selftest/live_coherency
Testcase: igt/gem_mmap_gtt/coherency
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100587
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tomasz Lis <tomasz.lis@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180720101910.11153-1-chris@chris-wilson.co.uk
Another step in the drv_module_reload fault-injection saga, is that we
try to disable the guc twice. Probably. It's a little unclear exactly
what is going on in the unload sequence that catches us out, so for the
time being suppress the assertion to get the test re-enabled.
Testcase: igt/drv_module_reload/basic-reload-inject
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Acked-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180720095144.5885-1-chris@chris-wilson.co.uk
Core Changes:
- add support for DisplayPort CEC-Tunneling-over-AUX (Hans Verkuil)
- more doc updates (Daniel Vetter)
- fourcc: Add is_yuv field to drm_format_info (Ayan Kumar Halder)
- dma-buf: correctly place BUG_ON (Michel Dänzer)
Driver Changes:
- more vkms support(Rodrigo Siqueira)
- many fixes and small improments to all drivers
-----BEGIN PGP SIGNATURE-----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=HyBh
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-07-18' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 4.19:
Core Changes:
- add support for DisplayPort CEC-Tunneling-over-AUX (Hans Verkuil)
- more doc updates (Daniel Vetter)
- fourcc: Add is_yuv field to drm_format_info (Ayan Kumar Halder)
- dma-buf: correctly place BUG_ON (Michel Dänzer)
Driver Changes:
- more vkms support(Rodrigo Siqueira)
- many fixes and small improments to all drivers
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180718200826.GA20165@juma
On KBL, WHL RVPs, booting up with an external display connected, triggers
below warning, when the BiOS brings up the external display too.
This warning is not seen during hotplug.
[ 3.615226] ------------[ cut here ]------------
[ 3.619829] plane 1A assertion failure (expected on, current off)
[ 3.632039] WARNING: CPU: 2 PID: 354 at drivers/gpu/drm/i915/intel_display.c:1294 assert_plane+0x71/0xbb
[ 3.633920] iwlwifi 0000:00:14.3: loaded firmware version 38.c0e03d94.0 op_mode iwlmvm
[ 3.647157] Modules linked in: iwlwifi cfg80211 btusb btrtl btbcm btintel bluetooth ecdh_generic
[ 3.647163] CPU: 2 PID: 354 Comm: frecon Not tainted 4.17.0-rc7-50176-g655af12d39c2 #3
[ 3.647165] Hardware name: Intel Corporation CoffeeLake Client Platform/WhiskeyLake U DDR4 ERB, BIOS CNLSFWR1.R00.X140.B00.1804040304 04/04/2018
[ 3.684509] RIP: 0010:assert_plane+0x71/0xbb
[ 3.764451] Call Trace:
[ 3.766888] intel_atomic_commit_tail+0xa97/0xb77
[ 3.771569] intel_atomic_commit+0x26a/0x279
[ 3.771572] drm_atomic_helper_set_config+0x5c/0x76
[ 3.780670] __drm_mode_set_config_internal+0x66/0x109
[ 3.780672] drm_mode_setcrtc+0x4c9/0x5cc
[ 3.780674] ? drm_mode_getcrtc+0x162/0x162
[ 3.789774] ? drm_mode_getcrtc+0x162/0x162
[ 3.798108] drm_ioctl_kernel+0x8d/0xe4
[ 3.801926] drm_ioctl+0x27d/0x368
[ 3.805311] ? drm_mode_getcrtc+0x162/0x162
[ 3.805314] ? selinux_file_ioctl+0x14e/0x199
[ 3.805317] vfs_ioctl+0x21/0x2f
[ 3.813812] do_vfs_ioctl+0x491/0x4b4
[ 3.813813] ? security_file_ioctl+0x37/0x4b
[ 3.813816] ksys_ioctl+0x55/0x75
[ 3.820672] __x64_sys_ioctl+0x1a/0x1e
[ 3.820674] do_syscall_64+0x51/0x5f
[ 3.820678] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 3.828221] RIP: 0033:0x7b5e04953967
[ 3.835504] RSP: 002b:00007fff2eafb6f8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[ 3.835505] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007b5e04953967
[ 3.835505] RDX: 00007fff2eafb730 RSI: 00000000c06864a2 RDI: 000000000000000f
[ 3.835506] RBP: 00007fff2eafb720 R08: 0000000000000000 R09: 0000000000000000
[ 3.835507] R10: 0000000000000070 R11: 0000000000000246 R12: 000000000000000f
[ 3.879988] R13: 000056bc9dd7d210 R14: 00007fff2eafb730 R15: 00000000c06864a2
[ 3.887081] Code: 48 c7 c7 06 71 a5 be 84 c0 48 c7 c2 06 fd a3 be 48 89 f9 48 0f 44 ca 84 db 48 0f 45 d7 48 c7 c7 df d3 a4 be 31 c0 e8 af a0 c0 ff <0f> 0b eb 2b 48 c7 c7 06 fd a3 be 84 c0 48 c7 c2 06 71 a5 be 48
[ 3.905845] WARNING: CPU: 2 PID: 354 at drivers/gpu/drm/i915/intel_display.c:1294 assert_plane+0x71/0xbb
[ 3.920964] ---[ end trace dac692f4ac46391a ]---
The warning is seen when mode_setcrtc() is called for pipeB
during bootup and before we get a mode_setcrtc() for pipeA,
while doing update_crtcs() in intel_atomic_commit_tail().
Now since, plane1A is still active after commit, update_crtcs()
is done for pipeA and eventually update_plane() for plane1A.
intel_plane_state->ctl for plane1A is not updated since set_modecrtc() is
called for pipeB. So intel_plane_state->ctl for plane 1A will be 0x0.
So doing an update_plane() for plane1A, will result in clearing
PLANE_CTL_ENABLE bit, and hence the warning.
To fix this warning, force all active planes to recompute their states
in probe.
Changes in v8:
- Actually add Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Changes in v7:
- Move call to intel_initial_commit() after sanitize_watermarks()
Otherwise the plane update will still consult potentially bogus
watermarks we read out from the hardware. (Ville)
- Carry Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
from v6
Changes in v6:
- Handle EDEADLK for drm_atomic_get_crtc_state() and
drm_atomic_add_affected_planes()
- Remove optimization of calling intel_initial_commit()
only when there is more than one active pipe in probe.
- Avoid using intel_ types.
Changes in v5:
- Drop drm_modeset_lock_all_ctx() since locks will be taken later.
Changes in v4:
- Handle locking in intel_initial_commit()
- Move the for loop inside intel_initial_commit() so that
drm_atomic_commit() is called only once
- Call intel_initial_commit() only for more than one active crtc on boot.
- Save the return value of intel_initial_commit() and print a message in
case of an error
Changes in v3:
- Add comments
Changes in v2:
- Force all planes to recompute their states.(Ville Syrjälä)
- Update the commit message
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530902250-44583-1-git-send-email-azhar.shaikh@intel.com
We believe we have all the kinks worked out, even for the early
Valleyview devices, for whom we currently disable all ppgtt.
References: 62942ed727 ("drm/i915/vlv: disable PPGTT on early revs v3")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180717095751.1034-2-chris@chris-wilson.co.uk
We should we have all the kinks worked out and full-ppgtt now works
reliably on gen7 (Ivybridge, Valleyview/Baytrail and Haswell). If we can
let userspace have full control over their own ppgtt, it makes softpinning
far more effective, in turn making GPU dispatch far more efficient by
virtue of better mm segregation. On the other hand, switching over to a
different GTT for every client does incur noticeable overhead, but only
for very lightweight tasks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jason Ekstrand <jason.ekstrand@intel.com>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Acked-by: Kenneth Graunke <kenneth@whitecape.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180717095751.1034-1-chris@chris-wilson.co.uk
We broke the LVDS notifier resume thing in (presumably) commit
e2c8b8701e ("drm/i915: Use atomic helpers for suspend, v2.") as
we no longer duplicate the current state in the LVDS notifier and
thus we never resume it properly either.
Instead of trying to fix it again let's just kill off the lid
notifier entirely. None of the machines tested thus far have
apparently needed it. Originally the lid notifier was added to
work around cases where the VBIOS was clobbering some of the
hardware state behind the driver's back, mostly on Thinkpads.
We now have a few report of Thinkpads working just fine without
the notifier. So maybe it was misdiagnosed originally, or
something else has changed (ACPI video stuff perhaps?).
If we do end up finding a machine where the VBIOS is still causing
problems I would suggest that we first try setting various bits in
the VBIOS scratch registers. There are several to choose from that
may instruct the VBIOS to steer clear.
With the notifier gone we'll also stop looking at the panel status
in ->detect().
v2: Nuke enum modeset_restore (Rodrigo)
Cc: stable@vger.kernel.org
Cc: Wolfgang Draxinger <wdraxinger.maillist@draxit.de>
Cc: Vito Caputo <vcaputo@pengaru.com>
Cc: kitsunyan <kitsunyan@airmail.cc>
Cc: Joonas Saarinen <jza@saunalahti.fi>
Tested-by: Vito Caputo <vcaputo@pengaru.com> # Thinkapd X61s
Tested-by: kitsunyan <kitsunyan@airmail.cc> # ThinkPad X200
Tested-by: Joonas Saarinen <jza@saunalahti.fi> # Fujitsu Siemens U9210
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105902
References: https://lists.freedesktop.org/archives/intel-gfx/2018-June/169315.html
References: https://bugs.freedesktop.org/show_bug.cgi?id=21230
Fixes: e2c8b8701e ("drm/i915: Use atomic helpers for suspend, v2.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180717174216.22252-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
There's a race between idling the engine and finishing off the last
tasklet (as we may kick the tasklets after declaring an individual
engine idle). However, since we do not need to access the device until
we try to submit to the ELSP register (processing the CSB just requires
normal CPU access to the HWSP, and when idle we should not need to
submit!) we can defer the assertion unto that point. The assertion is
still useful as it does verify that we do hold the longterm GT wakeref
taken from request allocation until request completion.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107274
Fixes: 9512f985c3 ("drm/i915/execlists: Direct submission of new requests (avoid tasklet/ksoftirqd)")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180719075029.28643-1-chris@chris-wilson.co.uk
If we call into the shrinker for direct relcaim inside kmalloc, it will
retire the requests. If we retire the vma->last_active while processing a
new i915_vma_move_to_active() we can upset the delicate bookkeeping
required for the cache. After the possible invocation of the shrinker, we
need to double check the vma->last_active is still valid.
Fixes: 8b293eb53a ("drm/i915: Track the last-active inside the i915_vma")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105600#c39
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180719072206.16015-1-chris@chris-wilson.co.uk
We make a decision at module load whether to use the GuC backend or not,
but lose that setup across set-wedge. Currently, the guc doesn't
override the engine->set_default_submission hook letting execlists sneak
back in temporarily on unwedging leading to an unbalanced park/unpark.
v2: Remove comment about switching back temporarily to execlists on
guc_submission_disable(). We currently only call disable on shutdown,
and plan to also call disable before suspend and reset, in which case we
will either restore guc submission or mark the driver as wedged, making
the reset back to execlists pointless.
v3: Move reset.prepare across
Fixes: 63572937ce ("drm/i915/execlists: Flush pending preemption events during reset")
Testcase: igt/drv_module_reload/basic-reload-inject
Testcase: igt/gem_eio
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180717202932.1423-1-chris@chris-wilson.co.uk
RC model has these parameters that correspond with each of
15 ranges of RC buffer threshold value in the RC model.
The three elements are range_min_qp, range_max_qp and
range_bpg_offset.
Add the Rate Control range values for eDP/MIPI and DP case.
The actual values are calculated usung a helper function.
This patch adds the shifts to registers where the value will
be written during atomic commit.
v2:
- Use _MMIO_PIPE() instead of _MMIO(_PICK()) (Manasi)
- Combine shifts (Manasi)
Cc: Jose Souza <jose.souza@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1531861861-10950-4-git-send-email-anusha.srivatsa@intel.com
Add register defines and shifts that control the RC buffer threshold
between encoder and decoder for eDP/MIPI and DP cases.
The actual values are calculated usung a helper function.
This patch adds the shifts to registers where the value will
be written during atomic commit.
v2:
- Use _MMIO_PIPE() instead of _MMIO_(_PICK()) (Manasi)
- Combine shifts (Manasi)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1531861861-10950-3-git-send-email-anusha.srivatsa@intel.com
Display Stream Compression(DSC) has a set of Picture
Parameter Set(PPS) components that the encoder must
communicate to the decoder.
This patch adds register definitions to
the PPS parameters for eDP/MIPI case and Display Port.
v2:
- Use _MMIO_PIPE instead of _MMIO(_PICK()). (Manasi)
- Use DSC constants as arguments. (Manasi)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1531861861-10950-2-git-send-email-anusha.srivatsa@intel.com
The Picture Parameter Set metadata for DSC has to be sent
to the panel through secondary data packets. Add the error
correction registers, data registers and control registers
for the same.
The control registers for transcoders A and B are already
defined and will be reused for Icelake purpose. This patch adds
Control register for EDP and transcoder C apart from adding the
PPS data and error registers.
v2: reuse MMIO_TRANS2 for _PPS_DATA and _PPS_ECC.
The _MMIO_TRANS2(pipe, reg) macro definition takes care of the eDp case
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1531861861-10950-1-git-send-email-anusha.srivatsa@intel.com
It was originally introduced following the VESA spec in order to validate PSR.
However we found so many issues around sink_crc that instead of helping PSR
development it only brought another layer of trouble to the table.
So, sink_crc has been a black whole for us in question of time, effort and hope.
First of the problems is that HW statement is clear: "Do not attempt to use
aux communication with PSR enabled". So the main reason behind sink_crc is
already compromised.
For a while we had hope on the aux-mutex could workaround this problem on SKL+
platforms, but that mutex was not reliable, not tested,
and we shouldn't use according to HW engineers.
Also, nor source, nor sink designed and implemented the sink_crc to be used like
we are trying to use here.
Well, the sink side of things is also apparently not prepared for this
case. Each panel that we tried seemed to have a different behavior with same
code and same source.
So, for all the time we lost on trying to ducktape all these different issues
I believe it is now time to move PSR to a more reliable validation.
Maybe not a perfect one as we dreamed for this sink_crc, but at least more
reliable.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705192528.30515-1-rodrigo.vivi@intel.com
power well support and begin of DSI support addition. Also there were many improvements
on execlists and interrupts for minimal latency on command submission; and many fixes
on selftests, mostly caught by our CI.
General driver:
- Clean-up on aux irq (Lucas)
- Mark expected switch fall-through for dealing with static analysis tools (Gustavo)
Gem:
- Different fixes for GuC (Chris, Anusha, Michal)
- Avoid self-relocation BIAS if no relocation (Chris)
- Improve debugging cases in on EINVAL return and vma allocation (Chris)
- Fixes and improvements on context destroying and freeing (Chris)
- Wait for engines to idle before retiring (Chris)
- Many improvements on execlists and interrupts for minimal latency on command submission (Chris)
- Many fixes in selftests, specially on cases highlighted on CI (Chris)
- Other fixes and improvements around GGTT (Chris)
- Prevent background reaping of active objects (Chris)
Display:
- Parallel modeset cleanup to fix driver reset (Chris)
- Get AUX power domain for DP main link (Imre)
- Clean-up on PSR unused func pointers (Rodrigo)
- Many PSR/PSR2 fixes and improvements (DK, Jose, Tarun)
- Add a PSR1 live status (Vathsala)
- Replace old drm_*_{un/reference} with put,get functions (Thomas)
- FBC fixes (Maarten)
- Abstract and document the usage of picking macros (Jani)
- Remove unnecessary check for unsupported modifiers for NV12. (DK)
- Interrupt fixes for display (Ville)
- Clean up on sdvo code (Ville)
- Clean up on current DSI code (Jani)
- Remove support for legacy debugfs crc interface (Maarten)
- Simplify get_encoder_power_domains (Imre)
Icelake:
- MG PLL fixes (Imre)
- Add hw workaround for alpha blending (Vandita)
- Add power well support (Imre)
- Add Interrupt Support (Anusha)
- Start to add support for DSI on Ice Lake (Madhav)
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbQ+ShAAoJEPpiX2QO6xPKas0H/igf9RFubtkMK7gHTef4FM+d
Bg+Qaq+O1vXlS/gidimL4NsVp1FxkejuCab0IffbTMvvjY0mv5NUA3kiIreAB0QZ
XO2hXr4fjjOINAQrdv5wiVMOqRjDws+fPgFFgZ8s5h1aJbofO27fjY/1MNtHwcA0
8VgtABpk+D3mkWvI8VTL0jCjYk2KocEvqUciz/Y7SQcPGV1iYFXqgBt5PR//rSvP
DU3u4R3KJGLDFbQwbe3uz2GxMfodAI6ijrqFeiizNSVqZORdTwnWlzKi6b6Cj9gl
SuleZacHPfv/+Ia7jmbmBqJEqi2GiAs948ne8QWL5/hsB9MMFO/UzwX/wYLNrP4=
=w6zC
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2018-07-09' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
Higlights here goes to many PSR fixes and improvements; to the Ice lake work with
power well support and begin of DSI support addition. Also there were many improvements
on execlists and interrupts for minimal latency on command submission; and many fixes
on selftests, mostly caught by our CI.
General driver:
- Clean-up on aux irq (Lucas)
- Mark expected switch fall-through for dealing with static analysis tools (Gustavo)
Gem:
- Different fixes for GuC (Chris, Anusha, Michal)
- Avoid self-relocation BIAS if no relocation (Chris)
- Improve debugging cases in on EINVAL return and vma allocation (Chris)
- Fixes and improvements on context destroying and freeing (Chris)
- Wait for engines to idle before retiring (Chris)
- Many improvements on execlists and interrupts for minimal latency on command submission (Chris)
- Many fixes in selftests, specially on cases highlighted on CI (Chris)
- Other fixes and improvements around GGTT (Chris)
- Prevent background reaping of active objects (Chris)
Display:
- Parallel modeset cleanup to fix driver reset (Chris)
- Get AUX power domain for DP main link (Imre)
- Clean-up on PSR unused func pointers (Rodrigo)
- Many PSR/PSR2 fixes and improvements (DK, Jose, Tarun)
- Add a PSR1 live status (Vathsala)
- Replace old drm_*_{un/reference} with put,get functions (Thomas)
- FBC fixes (Maarten)
- Abstract and document the usage of picking macros (Jani)
- Remove unnecessary check for unsupported modifiers for NV12. (DK)
- Interrupt fixes for display (Ville)
- Clean up on sdvo code (Ville)
- Clean up on current DSI code (Jani)
- Remove support for legacy debugfs crc interface (Maarten)
- Simplify get_encoder_power_domains (Imre)
Icelake:
- MG PLL fixes (Imre)
- Add hw workaround for alpha blending (Vandita)
- Add power well support (Imre)
- Add Interrupt Support (Anusha)
- Start to add support for DSI on Ice Lake (Madhav)
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Tue 10 Jul 2018 08:41:37 AM AEST
# gpg: using RSA key FA625F640EEB13CA
# gpg: Good signature from "Rodrigo Vivi <rodrigo.vivi@intel.com>"
# gpg: aka "Rodrigo Vivi <rodrigo.vivi@gmail.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6D20 7068 EEDD 6509 1C2C E2A3 FA62 5F64 0EEB 13CA
Link: https://patchwork.freedesktop.org/patch/msgid/20180710234349.GA16562@intel.com
If the driver is wedged, we skip idling the GPU. However, we may still
have a few requests still not retired following the wedging (since they
will be waiting for a background worker trying to acquire struct_mutex).
As we hold the struct_mutex, always do a quick request retirement in
order to flush the wedged path.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107257
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180717084121.28185-1-chris@chris-wilson.co.uk
This is the final step for more generic support of DRM audio
component. The generic audio component code is now moved to its own
file, and the symbols are renamed from snd_hac_i915_* to
snd_hdac_acomp_*, respectively. The generic code is enabled via the
new kconfig, CONFIG_SND_HDA_COMPONENT, while CONFIG_SND_HDA_I915 is
kept as the super-class.
Along with the split, three new callbacks are added to audio_ops:
pin2port is for providing the conversion between the pin number and
the widget id, and master_bind/master_unbin are called at binding /
unbinding the master component, respectively. All these are optional,
but used in i915 implementation and also other later implementations.
A note about the new snd_hdac_acomp_init() function: there is a slight
difference between this and the old snd_hdac_i915_init(). The latter
(still) synchronizes with the master component binding, i.e. it
assures that the relevant DRM component gets bound when it returns, or
gives a negative error. Meanwhile the new function doesn't
synchronize but just leaves as is. It's the responsibility by the
caller's side to synchronize, or the caller may accept the
asynchronous binding on the fly.
v1->v2: Fix missing NULL check in master_bind/unbind
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For allowing other drivers to use the DRM audio component, rename the
i915_audio_component_* with drm_audio_component_*, and split the
generic part into drm_audio_component.h. The i915 specific stuff
remains in struct i915_audio_component, which contains
drm_audio_component as the base.
The license of drm_audio_component.h is kept to MIT as same as the the
original i915_component.h.
This is a preliminary change for further development, and no
functional changes by this patch itself, merely code-split and
renames.
v1->v2: Use SPDX for drm_audio_component.h, fix remaining i915
argument in drm_audio_component.h
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Our I915g (early gen3, the oldest machine we have in the farm) is still
reporting occasional incoherency performing the following operations:
1) write through GGTT (indirect write into memory)
2) write through either CPU or WC (direct write into memory)
3) read from GGTT (indirect read)
Instead of reporting the value from (2), the read from GGTT reports the
earlier value written via the GGTT. We have made sure that the writes are
flushed from the CPU (commit 3a32497f0d ("drm/i915/selftests: Provide
full mb() around clflush") and commit add00e6d89 ("drm/i915: Flush the
WCB following a WC write")), but still see the error, just less
frequently. The only remaining cache that might be affected here is a
chipset cache, so flush that as well.
Testcase: igt/drv_selftest/live_coherency #gdg
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180717092655.28417-1-chris@chris-wilson.co.uk
In the huge pages tests, we may have lots of objects being trapped on
the freelist as we hold the struct_mutex allowing the free worker no
opportunity to recover the backing store. We also have stricter
requirements and the desire for large contiguous pages, further
increasing the allocation pressure. To reduce the chance of running out
of memory, we could either drop the mutex and flush the free worker, or
we could release the backing store directly. We do the latter in this
patch for simplicity.
References: https://bugs.freedesktop.org/show_bug.cgi?id=107254
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180717082334.18774-1-chris@chris-wilson.co.uk
We must be able to reset the GPU while we are waiting on it to perform
an eviction (unbinding an active vma). So attach a spinning request to a
target vma and try and it evict it from a thread to see if that blocks
indefinitely.
v2: Add a wait for the thread to start just in case that takes more than
10ms...
v3: complete() not completion_done() to signal the completion.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180716134009.13143-1-chris@chris-wilson.co.uk
Inject a failure into preemption completion to pretend as if the HW
didn't successfully handle preemption and we are forced to do a reset in
the middle.
v2: Wait for preemption, to force testing with the missed preemption.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180716132154.12539-1-chris@chris-wilson.co.uk
On reset/wedging, we cancel all pending replies from the HW and we also
want to cancel an outstanding preemption event. Since we use the same
function to cancel the pending replies for reset and for a preemption
event, we can simply clear the active tracking for all.
v2: Keep execlists_user_end() markup for wedging
v3: Move assignment to inline to hide the bare assignment.
Fixes: 60a9432454 ("drm/i915/execlists: Drop clear_gtiir() on GPU reset")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180716125424.5715-1-chris@chris-wilson.co.uk
If we declare the driver wedged before the GPU truly is, then we may see
the GPU complete some CS events following our cancellation. This leaves
us quite confused as we deleted all the bookkeeping and thus complain
about the inconsistent state.
We can just ignore the remaining events and let the GPU idle by not
feeding it, and so avoid trying to racily overwrite shared state. We
rely on there being a full GPU reset before unwedging, giving us the
opportunity to reset the shared state.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107188
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180716080332.32283-4-chris@chris-wilson.co.uk
On an aborted module load, we unwind and free our device private - but
we left a dangling pointer to our privates inside the pci_device. After
the attempted aborted unload, we may still get a call to i915_pci_remove()
when the module is removed, potentially chasing stale data.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180716080332.32283-5-chris@chris-wilson.co.uk
Give in, since CI continues to incorrectly insist that KERN_NOTICE is a
warning and flags the timeout message as unwanted spam. At first, the
intention was to use the message to indicate which tests might warrant
an extended run, but virtually all tests require a timeout so it is
simply not as interesting as first thought.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103667
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180716080332.32283-6-chris@chris-wilson.co.uk
We're seeing "RPM wakelock ref not held during HW access" warning
otherwise. Since IRQs are synced for runtime suspend we can just disable
the wakeref asserts.
Reported-by: Marta Löfstedt <marta.lofstedt@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105710
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180714173703.7894-1-chris@chris-wilson.co.uk
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Inside intel_engine_is_idle(), we flush the tasklet to ensure that is
being run in a timely fashion (ksoftirqd has taught us to expect the
worst). However, if we are in the middle of reset, the HW may not yet be
ready to execute the submission tasklet and so we must respect the
disable flag.
Fixes: dd0cf235d8 ("drm/i915: Speed up idle detection by kicking the tasklets")
Testcase: igt/drv_selftest/live_hangcheck
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180713203529.1973-2-chris@chris-wilson.co.uk
Since there's very few callers of these I've decided to do them all in
one patch. With this the unecessarily long drm_mode_connector_ prefix
is gone from the codebase! The only exception being struct
drm_mode_connector_set_property, which is part of the uapi so can't be
renamed.
Again done with sed+some manual fixups for indent issues.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709084016.23750-8-daniel.vetter@ffwll.ch
We're doing a pointless translation from hpd_pin to port simply for
passing the thing to long_pulse_detect(). Let's pass the hpd_pin
directly instead.
This removes the assumption that the hpd_pin and port always
match. The only other place where we make that assumption anymore
is intel_hpd_pin_default() and that's fine as it's what determines
the relationship between the two. If we ever get hardware where
the hpd pins are wired in more interesting ways it should be
trivial to handle from now on.
This should also fix the IS_CNL_WITH_PORT_F() case as that mapped
pin E back to port F and passed that to
spt_port_hotplug2_long_detect() which would always return false
for port F. Now that we pass in pin E directly it'll actually
do the right thing.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Fixes: cf53902f48 ("drm/i915/cnl: Add HPD support for Port F.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705164357.28512-7-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Instead of looping over ports and hpd_pins, let's loop over
the encoders when doing hotplug processing. And instead of
depending on dev_priv->irq_port[] to tell us whether the
encoder has the ->hpd_pulse() hook or not, we can just
check for that directly. So we can just nuke irq_port[] entirely.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705164357.28512-5-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Rather than looping over all the ports and picking the encoder based on
the port, let's just loop over all the encoders instead. Gets rid of
some irq_port[] usage, which is a bit of an eye sore.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705164357.28512-4-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
On gen8 and onwards, we can mark GPU accesses through the ppGTT as being
read-only, that is cause any GPU write onto that page to be discarded
(not triggering a fault). This is all that we need to finally support
the read-only flag for userptr!
v2: Check default address space for read only support as a proxy for the
user context/ppgtt.
Testcase: igt/gem_userptr_blits/readonly*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712191430.9269-1-chris@chris-wilson.co.uk
If the user created a read-only object, they should not be allowed to
circumvent the write protection using the pwrite ioctl.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712185315.3288-5-chris@chris-wilson.co.uk
If the user has created a read-only object, they should not be allowed
to circumvent the write protection by using a GGTT mmapping. Deny it.
Also most machines do not support read-only GGTT PTEs, so again we have
to reject attempted writes. Fortunately, this is known a priori, so we
can at least reject in the call to create the mmap (with a sanity check
in the fault handler).
v2: Check the vma->vm_flags during mmap() to allow readonly access.
v3: Remove VM_MAYWRITE to curtail mprotect()
Testcase: igt/gem_userptr_blits/readonly_mmap*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com> #v1
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712185315.3288-4-chris@chris-wilson.co.uk
GVT is not propagating the PTE bits, and is always setting the
read-write bit, thus breaking read-only support.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712185315.3288-3-chris@chris-wilson.co.uk
Hook up the flags to allow read-only ppGTT mappings for gen8+
v2: Include a selftest to check that writes to a readonly PTE are
dropped
v3: Don't duplicate cpu_check() as we can just reuse it, and even worse
don't wholesale copy the theory-of-operation comment from igt_ctx_exec
without changing it to explain the intention behind the new test!
v4: Joonas really likes magic mystery values
Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712185315.3288-2-chris@chris-wilson.co.uk
We can set a bit inside the ppGTT PTE to indicate a page is read-only;
writes from the GPU will be discarded. We can use this to protect pages
and in particular support read-only userptr mappings (necessary for
importing PROT_READ vma).
Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712185315.3288-1-chris@chris-wilson.co.uk
On GLK NUC platforms the HDMI retiming buffer needs additional disabled
time to correctly sync to a faster incoming signal.
When measured on a scope the highspeed lines of the HDMI clock turn off
for ~400uS during a normal resolution change. The HDMI retimer on the
GLK NUC appears to require at least a full frame of quiet time before a
new faster clock can be correctly sync'd. Wait 100ms due to msleep
inaccuracies while waiting for a completed frame. Add a quirk to the
driver for GLK boards that use ITE66317 HDMI retimers.
V2: Add more devices to the quirk list
V3: Delay increased to 100ms, check to confirm crtc type is HDMI.
V4: crtc type check extended to include _DDI and whitespace fixes
v5: Fix white spaces, remove the macro for delay. Revert the crtc type
check introduced in v4.
Cc: Imre Deak <imre.deak@intel.com>
Cc: <stable@vger.kernel.org> # v4.14+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105887
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Tested-by: Daniel Scheller <d.scheller.oss@gmail.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710200205.1478-1-radhakrishna.sripada@intel.com
This patchs adds the cec_notifier feature to the intel_hdmi part
of the i915 DRM driver. It uses the HDMI DRM connector name to differentiate
between each HDMI ports.
The changes will allow the i915 HDMI code to notify EDID and HPD changes
to an eventual CEC adapter.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reduce the module parameter to enable or disable.
The link stand by vs full link off was used only once.
And it was actually masking another bug fixed by commit
'84bb2916a683 ("drm/i915/psr: Check for SET_POWER_CAPABLE
bit at PSR init time.")'
So, let's remove these options for now. End goal is to
fully remove the mod param, moving it to a debugfs
interface in upcoming patches.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Tarun Vyas <tarun.vyas@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712052715.8177-1-rodrigo.vivi@intel.com
This allows to read i915_edp_psr_status from tests without triggering
any AUX communication. Take this opportunity to move this under the
eDP-1 connector directory as the status we print is of the sink.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Suggested-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705003121.2478-1-dhinakaran.pandiyan@intel.com
In commit "drm/i915: Wait for PSR exit before checking for vblank
evasion", the idea was to limit the PSR IDLE checks when PSR is
actually supported. While CAN_PSR does do that check, it doesn't
applies on a per-crtc basis. crtc_state->has_psr is a more granular
check that only applies to pipe(s) that have PSR enabled.
Without the has_psr check, we end up waiting on the eDP transcoder's
PSR_STATUS register irrespective of whether the pipe being updated is
driving it or not.
v2: Remove unnecessary parantheses, make checkpatch happy.
v3: Move the has_psr check to intel_psr_wait_for_idle and commit
message changes (DK).
v4: Derive dev_priv from intel_crtc_state (DK)
v5: Commit message changes to reflect the HW behavior (DK)
Fixes: a608987970 ("drm/i915: Wait for PSR exit before checking for vblank evasion")
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Tarun Vyas <tarun.vyas@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712053323.26266-1-tarun.vyas@intel.com
Support for Burst read in HW is added for HDCP2.2 compliance
requirement.
This patch enables the burst read for all the gmbus read of more than
511Bytes, on capable platforms.
v2:
Extra line is removed.
v3:
Macro is added for detecting the BURST_READ Support [Jani]
Runtime detection of the need for burst_read [Jani]
Calculation enhancement.
v4:
GMBUS0 reg val is passed from caller [ville]
Removed a extra var [ville]
Extra brackets are removed [ville]
Implemented the handling of 512Bytes Burst Read.
v5:
Burst read max length is fixed at 767Bytes [Ville]
v6:
Collecting the received reviewed-by.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1530192889-5789-3-git-send-email-ramalingam.c@intel.com
GMBUS HW supports 511Bytes as Max Bytes per single RD/WR op. Instead of
enabling the 511Bytes per RD/WR cycle on legacy platforms for no
absolute ROIs, this change allows the max bytes per op upto 511Bytes
from Gen9 onwards.
v2:
No Change.
v3:
Inline function for max_xfer_size and renaming of the macro.[Jani]
v4:
Extra brackets removed [ville]
Commit msg is modified.
v5:
Collecting the Reviewed-By received.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1530192889-5789-2-git-send-email-ramalingam.c@intel.com
Since:
0d4b78b3d2 ("drm/i915/guc: Assert we have the doorbell before setting it up")
We have asserts in GuC doorbell related functions, which is a good thing.
Unfortunately, we were using those to check whether GuC FW is refusing
to allocate invalid doorbell - which makes the test fail.
Well, it would make the test WARN, except we fumbled cleanup ordering
and eat the BUG_ON instead.
Let's keep the asserts and use the internal implementation in the test.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107186
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712112013.3253-1-chris@chris-wilson.co.uk
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Let's reorder things so that we can do onion teardown rather than double
goto.
References: b96f6ebfd0 ("drm/i915: Correctly handle error path in i915_gem_init_hw")
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712124810.25241-1-michal.winiarski@intel.com
If we fail the module load, we may try and cleanup before we even
allocate the GuC clients. KISS in order to try and re-enable
drv_module_reload for BAT.
Testcase: igt/drv_module_reload/basic-reload-inject
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712105830.20390-1-chris@chris-wilson.co.uk
The kernel recently gained an augmented rbtree with the purpose of
cacheing the leftmost element of the rbtree, a frequent optimisation to
avoid calls to rb_first() which is also employed by the
execlists->queue. Switch from our open-coded cache to the library.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180629075348.27358-9-chris@chris-wilson.co.uk
Since live_workarounds poke around the w/a registers and checks to see
if they survive across a reset, we are prone to fouling the machine and
leaving it in a non-recoverable state. Wrap the probe inside a timeout
to abort the test if the reset fails.
v2: Include GEM_TRACE on declaring wedged.
v3: Add a few includes to make the header look standalone.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107188
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180711122952.18448-1-chris@chris-wilson.co.uk
Add a mutex into struct i915_address_space to be used while operating on
the vma and their lists for a particular vm. As this may be called from
the shrinker, we taint the mutex with fs_reclaim so that from the start
lockdep warns us if we are caught holding the mutex across an
allocation. (With such small steps we will eventually rid ourselves of
struct_mutex recursion!)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180711073608.20286-2-chris@chris-wilson.co.uk
Now that our stolen memory is already reserved by the x86 subsystem
(since commit "x86/gpu: reserve ICL's graphics stolen memory"), make
use of it.
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: x86@kernel.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180504203252.28048-2-paulo.r.zanoni@intel.com
On unwinding following a critical failure inside GEM init, we also need
to be sure to flush the workers before unloading the module.
Testcase: igt/drv_module_reload/basic-reload-inject
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710094421.16223-1-chris@chris-wilson.co.uk
In the next patch, we will make a fairly minor change to flush
outstanding resets before suspend. In order to keep churn to a minimum
in that functional patch, we fix up the comments and coding style now.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709130208.11730-7-chris@chris-wilson.co.uk
Across a reset, the seqno (and thus hangcheck) should restart and the
hangcheck naturally progress, for when it does not, we want to declare an
emergency. Currently, we only detect if reset and reinit fails, but we
do not detect if the call to reinit succeeds but the HW is fried - as we
are resetting hangcheck on initialisation the engine. Remove that and
rely on the natural progress to reset the hangcheck timer.
References: e21b141376 ("drm/i915: Mark the hangcheck as idle when unparking the engines")
References: 1fd00c0fae ("drm/i915: Declare the driver wedged if hangcheck makes no progress")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709130208.11730-2-chris@chris-wilson.co.uk
In our swizzling selftests, we cannot predict the physical address of
the target page (at least not simply!) and so skip bit17 swizzles.
However, there are two bit17 swizzle modes and we only skipped one, with
the second being observed on the lab gdg causing the test to fail,
as soon as we hit a page with bit17 set in its address.
Testcase: igt/drv_selftest/live_objects #gdg
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709194915.5789-1-chris@chris-wilson.co.uk
Be pessimistic and presume that we actually allocate every page we
exercise via the mock_gtt (e.g. for gvt). In which case we have to keep
our working set under the available physical memory to prevent oom.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710080424.7821-1-chris@chris-wilson.co.uk
Error messages are intended to be addressed to the user; be clear,
succinct, instructive and unambiguous. Adding the function name to
that message does not add any information the user requires and in
the process makes the message less clear.
E.g.
[ 245.539711] i915 0000:00:02.0: [drm:i915_gem_init [i915]] Failed to initialize GPU, declaring it wedged!
becomes
[ 245.539711] i915 0000:00:02.0: Failed to initialize GPU, declaring it wedged!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709134858.12446-1-chris@chris-wilson.co.uk
This helps initramfs builder and other tools to know the full dependencies
of i915 and have gvt module loaded with i915.
v2: add condition and change to pre-dependency (Chris)
v3: move declaration to gvt.c. (Chris)
v4: remove xengt (Zhenyu)
Signed-off-by: Hang Yuan <hang.yuan@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Just like with PIPESTAT, the edge triggered IIR on i965/g4x
also causes problems for hotplug interrupts. To make sure
we don't get the IIR port interrupt bit stuck low with the
ISR bit high we must force an edge in ISR. Unfortunately
we can't borrow the PIPESTAT trick and toggle the enable
bits in PORT_HOTPLUG_EN as that act itself generates hotplug
interrupts. Instead we just have to loop until we've cleared
PORT_HOTPLUG_STAT, or we just give up and WARN.
v2: Don't frob with PORT_HOTPLUG_EN
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614175625.1615-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit 0ba7c51a6f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In igt_flush_test() we install a background timer in order to ensure
that the wait completes within a certain time. We can now tell the wait
that it has to complete within a timeout, and so no longer need the
background timer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709122044.7028-3-chris@chris-wilson.co.uk
With a broken GPU we expect it to fail during the initial
GPU setup where do a couple of context switches to record the defaults.
This is a task that takes a few milliseconds even on the slowest of
devices, but we may have to wait 60s for hangcheck to give in and
declare the machine inoperable. In this a case where any gpu hang is
unacceptable, both from a timeliness and practical standpoint.
We can therefore set a timeout on our wait-for-idle that is shorter than
the hangcheck (which may be up to 60s for a declaring a wedged driver)
and so detect the broken GPU much more quickly during driver load (and
so prevent stalling userspace for ages).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709122044.7028-2-chris@chris-wilson.co.uk
Usually we have no idea about the upper bound we need to wait to catch
up with userspace when idling the device, but in a few situations we
know the system was idle beforehand and can provide a short timeout in
order to very quickly catch a failure, long before hangcheck kicks in.
In the following patches, we will use the timeout to curtain two overly
long waits, where we know we can expect the GPU to complete within a
reasonable time or declare it broken.
In particular, with a broken GPU we expect it to fail during the initial
GPU setup where do a couple of context switches to record the defaults.
This is a task that takes a few milliseconds even on the slowest of
devices, but we may have to wait 60s for hangcheck to give in and
declare the machine inoperable. In this a case where any gpu hang is
unacceptable, both from a timeliness and practical standpoint.
The other improvement is that in selftests, we do not need to arm an
independent timer to inject a wedge, as we can just limit the timeout on
the wait directly.
v2: Include the timeout parameter in the trace.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709122044.7028-1-chris@chris-wilson.co.uk
BXT supports EDP. However since GVT-g only simulate DP monitor
to guest and handles EDP_PSR_IMR and EDP_PSR_IIR as default MMIO
r/w. If guest r/w these IMR/IIR, GVT-g won't simulate the real
HW behavior and below warning is printed:
--------
Interrupt register 0x64838 is not zero: 0xffffffff
WARNING: CPU: 1 PID: 1 at drivers/gpu/drm/i915/i915_irq.c:161
gen3_assert_iir_is_zero+0x34/0xa0
Call Trace:
gen8_de_irq_postinstall+0xad/0x330
gen8_irq_postinstall+0x23/0x80
drm_irq_install+0xb5/0x130
i915_driver_load+0xafd/0xf70
--------
Since GVT-g won't simulate EDP to guest, always set EDP_PSR_IMR
and EDP_PSR_IIR IMR/IIR to 0.
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Now GVTg supports shadowing both 2M/64K huge gtt pages. So let's turn on
the cap info bit VGT_CAPS_HUGE_GTT.
v2: Split changes in i915 side into a separated patch.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Don't forget to free allocated spt if shadowing failed.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
If the guest update the 64K gtt entry before changing IPS bit of PDE, we
need to re-shadow the whole page table. Because we have ignored all
updates to unused entries.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
This add 2M huge gtt support for GVTg. Unlike 64K gtt entry, we can
shadow 2M guest entry with real huge gtt. But before that, we have to
check memory physical continuous, alignment and if it is supported on
the host. We can get all supported page sizes from
intel_device_info.page_sizes.
Finally we must split the 2M page into smaller pages if we cannot
satisfy guest Huge Page.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
To support huge gtt, we need to support huge pages in kvmgt first.
This patch adds a 'size' param to the intel_gvt_mpt::dma_map_guest_page
API and implements it in kvmgt.
v2: rebase.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Finally, this add the first huge gtt support for GVTg - 64K pages. Since
64K page and 4K page cannot be mixed on the same page table, so we always
split a 64K entry into small 4K page. And when unshadow guest 64K entry,
we need ensure all the shadowed entries in shadow page table also get
cleared.
For page table which has 64K gtt entry, only PTE#0, PTE#16, PTE#32, ...
PTE#496 are used. Unused PTEs update should be ignored.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
64K PTE is special, only PTE#0, PTE#16, PTE#32, ... PTE#496 are used in
the page table.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
We need a interface to allocate a pure shadow page which doesn't have
a guest page associated with. Such shadow page is used to shadow 2M
huge gtt entry.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Add clear_pse operation in case we need to split huge gtt into small pages.
v2: correct description.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
This add a software PTE flag on the Ignored bit of PTE. It will be used
to identify splited 64K shadow entries.
v2: fix mask definition.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
This change help us detect the real entry type per PSE and IPS setting.
For 64K entry, we also need to check reg GEN8_GAMW_ECO_DEV_RW_IA.
v2: Extend IPS mmio control to Gen10. (Matthew Auld)
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
The register RENDER_HWS_PGA_GEN7 is renamed to GEN8_GAMW_ECO_DEV_RW_IA
from GEN8 which can control IPS enabling.
v3: MMIO control for IPS is not removed from gen9 but gen10 (Matthew Auld)
v2: IPS of all engines must be enabled together for gen9.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Add three IPS operation functions to test/set/clear IPS in PDE.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Add a new entry type GTT_TYPE_PPGTT_PTE_64K_ENTRY. 64K entry is very
different from 2M/1G entry. 64K entry is controlled by IPS bit in upper
PDE. To leverage the current logic, I take IPS bit as 'PSE' for PTE
level. Which means, 64K entries can also processed by get_pse_type().
v2: Make it bisectable.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
In the next patch, we will want a third distinct class of timeline that
may overlap with the current pair of client and engine timeline classes.
Rather than use the ad hoc markup of SINGLE_DEPTH_NESTING, initialise
the different timeline classes with an explicit subclass.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706210710.16251-1-chris@chris-wilson.co.uk
Inside the mock GEM device, we try to grab the runtime pm for the fake
device to prevent it from ever suspending. However, if CONFIG_PM is not
set, trying to obtain the wakref returns an error which we WARN about.
Suppress the expected warning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706205947.11209-1-chris@chris-wilson.co.uk
clflush is an unserialised instruction and the IA manual strongly advises
you to serialise it with a mb. To be cautious, apply one before and one
after, so that it is serialised with both writes and reads without
worrying too much about the required direction.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706174926.4712-1-chris@chris-wilson.co.uk
Using a VMA on more than one timeline concurrently is the exception
rather than the rule (using it concurrently on multiple engines). As we
expect to only use one active tracker, store the most recently used
tracker inside the i915_vma itself and only fallback to the rbtree if
we need a second or more concurrent active trackers.
v2: Comments on how we overwrite any existing last_active cache.
v3: __list_del_entry() before list_replace_init() is confusing and, much
more important, entirely redundant.
v4: Note that both last_active and the rbtree may be simultaneously
tracking this timeline, albeit with different requests, and so the vma
may be retired twice for the same timeline.
v5: No, that list_del is required!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706123157.9645-1-chris@chris-wilson.co.uk
In the next patch, we will want to be able to use more flexible request
timelines that can hop between engines. From the vma pov, we can then
not rely on the binding of this request to an engine and so can not
ensure that different requests are ordered through a per-engine
timeline, and so we must track activity of all timelines. (We track
activity on the vma itself to prevent unbinding from HW before the HW
has finished accessing it.)
v2: Switch to a rbtree for 32b safety (since using u64 as a radixtree
index is fraught with aliasing of unsigned longs).
v3: s/lookup_active/active_instance/ because we can never agree on names
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706103947.15919-5-chris@chris-wilson.co.uk
Handling such a late error in request construction is tricky, but to
accommodate future patches which may allocate here, we potentially could
err. To handle the error after already adjusting global state to track
the new request, we must finish and submit the request. But we don't
want to use the request as not everything is being tracked by it, so we
opt to cancel the commands inside the request.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706103947.15919-3-chris@chris-wilson.co.uk
In the next patch, we will want to start skipping requests on failing to
complete their payloads. So export the utility function current used to
make requests inoperable following a failed gpu reset.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706103947.15919-2-chris@chris-wilson.co.uk
Currently all callers are responsible for adding the vma to the active
timeline and then exporting its fence. Combine the two operations into
i915_vma_move_to_active() to move all the extra handling from the
callers to the single site.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706103947.15919-1-chris@chris-wilson.co.uk
Pull in the malidp writeback implementation for further work on writeback in drm-misc-next.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Replace the magic bit with the proper symbolic name for instructing
MI_STORE_DWORD_IMM to use a virtual address (on gen3) or the global GTT
address (still virtual!) on gen4+.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706142323.25699-1-chris@chris-wilson.co.uk
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Limit the GTT size we try and allocate to ensure that it fits within RAM
and does not trigger the oomkiller indiscriminately.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706125338.24432-1-chris@chris-wilson.co.uk
We already maually control the CPU cache for our page table directories,
so we can tell the dma mapper to skip doing it as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706122611.4142-2-chris@chris-wilson.co.uk
As we propagate back the error to the caller for them to handle, we do
not need the lowest level spitting out a redundant warning upon an
allocation failure inside dma_map_page().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706122611.4142-1-chris@chris-wilson.co.uk
If we have just completed a WC write, we must ensure that the WCB (Write
Combining Buffer) is flushed out to main memory before we can expect to
see the results. This is especially important when mixing WC with GTT as
the physical paths are different and cachelines are not naturally flushed.
Testcase: igt/drv_selftests/live_coherency #gdg
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706115402.18547-1-chris@chris-wilson.co.uk
If the GPU is irrecoverably wedged, we can not execute any requests
making testing execlists (request execution) pointless. Skip!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706114510.18467-1-chris@chris-wilson.co.uk
If the HW (or driver) doesn't support logical contexts, don't pretend we
gain anything from trying to execute GPU commands with them. At best it
reports -ENODEV, which is an unhelpful failure that we should just skip.
v2: Be more specific and check the driver/engine caps for logical (HW)
context support.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706101923.28548-1-chris@chris-wilson.co.uk
Avoid looking at the magical engines[RCS] to decide if the HW and driver
supports logical contexts, and instead record that knowledge during
initialisation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706101442.21279-1-chris@chris-wilson.co.uk
We can simplify the encoder's get_power_domains() hook by calling it
only if the encoder is active. That way the hook can return its power
domains unconditionally without checking the active state by calling
encoder::get_hw_state(). This get_hw_state() query is in fact
redundant since it's already done by intel_modeset_readout_hw_state()
setting the encoder's crtc or leaving it NULL accordingly. Let's use
this fact to decide if the encoder is active.
While at it clarify the comment in intel_ddi_get_power_domains() about
primary vs. fake MST encoders and make sure we never do an incorrect
encoder->dig_port cast for fake MST encoders.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705122654.17072-1-imre.deak@intel.com
This interface is deprecated, and has been replaced by the upstream
drm crc interface.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Cc: Petri Latvala <petri.latvala@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628072303.14175-1-maarten.lankhorst@linux.intel.com
If the GPU is terminally wedged we cannot submit any requests into a
context, completely unfulfilling our purpose of doing so. As this
expectedly fails, skip over the test.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706065332.15214-9-chris@chris-wilson.co.uk
We test the GPU handling of huge pages by submitting requests that write
into a huge page, but if the GPU is irrecoverably wedged we cannot
submit any requests. As the test expectedly fails, skip over it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706065332.15214-8-chris@chris-wilson.co.uk
If the GPU is irrecoverably wedged, we cannot submit any requests and so
cannot make the GTT busy in order to test evicting active objects. As
this expectedly fails, skip over the test.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706065332.15214-7-chris@chris-wilson.co.uk
If the GPU is irrecoverably wedged, we cannot submit any request and
therefore cannot query the register state of the context (which is done
using the GPU command stream). So skip over the test as it expectedly
fails.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706065332.15214-6-chris@chris-wilson.co.uk
As we keep VMA around until the object is destroyed, when testing
partial tiling we instantiate many, many VMA (as the object is huge
allowing for many different partial regions). We test elsewhere our
handling of populating large objects with a full set of VMA and checking
we can retrieve them afterwards, but in this test we incur the cost of
flushing all VMA after every GTT write, dramatically slowing down the
test.
References: https://bugs.freedesktop.org/show_bug.cgi?id=107130
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706065332.15214-2-chris@chris-wilson.co.uk
Having found the error causing the IGT test to fail, downgrade the
verbose logging so that we stop flooding the syslogs as we deliberately
provoke it many thousands of time during selftests.
References: 10195b1e44 ("drm/i915: Show vma allocator stack when in doubt")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706065332.15214-1-chris@chris-wilson.co.uk
This patch defines AUX lane registers for PORT_PCS_DW1,
PORT_TX_DW2, PORT_TX_DW4, PORT_TX_DW5 used during
dsi enabling.
v2: Review comments from Jani N:
- Define _ICL_PORT_PCS_DW1_AUX_A for consistency
- Three spaces for bitfield definition.
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530798591-2077-8-git-send-email-madhav.chauhan@intel.com
To save power, unused lanes should be powered
down using the bitfield of PORT_CL_DW10.
v2: Review comments from Jani N
- Put default label next to case 4
- Include the shifts in the macros
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530798591-2077-7-git-send-email-madhav.chauhan@intel.com
This register used to power down individual lanes for
DDI/DSI ports. Bitfields to power up/down various
combinations of lanes are also added in this patch.
v2: Review comments from Jani N
- Use override instead of "override" for bitfields
- Define mask for override bitfield
- Define PWR_DOWN_LN* macros shifted in place
v3: Correct PWR_DOWN_LN_MASK value (Jani N)
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530798591-2077-6-git-send-email-madhav.chauhan@intel.com
Escape Clock is used for LP communication across the DSI
Link. To achieve the constant frequency of the escape clock
from the variable DPLL frequency output, a variable divider(M)
is needed. This patch programs the same.
v2: (Jani N) Don't end line with "(".
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1530798591-2077-3-git-send-email-madhav.chauhan@intel.com
Use the more customary order of latest platform first, and don't bother
with an if in the last branch.
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705132509.12881-3-jani.nikula@intel.com
Avoid confusion with the functions to be added for the new ICL or gen 11
DSI implementation by renaming the current DSI functions. While at it,
permutate the words in the function names to make them all start with
"vlv_dsi" or "vlv_dsi_pll" etc.
Reduce the platform abstractions in the PLL file while at it, moving the
checks to vlv_dsi.c instead, where we typically already have the
necessary if ladders.
Leave the static functions as-is for now; they could be renamed later if
needed.
No functional changes.
v2: use "gen7" prefix.
v3: use "vlv" and "bxt" prefixes, reduce the abstractions.
References: https://patchwork.freedesktop.org/series/44823/
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705132509.12881-2-jani.nikula@intel.com
Starting from ICL or gen 11 we have a new DSI block which requires
completely different programming from the current implementation. Having
them in the same file would be confusing. Rename the current DSI and DSI
PLL implementation files as vlv_dsi.c and vlv_dsi_pll.c.
No functional changes.
v2: use "gen7" prefix.
v3: use "vlv" prefix.
References: https://patchwork.freedesktop.org/series/44823/
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705132509.12881-1-jani.nikula@intel.com
If the GPU is irrecoverably wedged on startup, it means that it failed
on initialisation and we have already tried to reset it but failed. We
can ignore all further testing, as it is already dead. Failing early,
prevents us from slowly failing in our endeavours later and timing out.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705150214.28316-1-chris@chris-wilson.co.uk
i915_gem_detect_bit_6_swizzle() tries to hide unknown swizzling from
userspace (and ourselves) leaving us with the only clue inside
i915->quirks & QUIRK_PIN_SWIZZLED_PAGES. If we see this bit set, it
means that we really have no clue as to what the swizzle pattern is
being used in any one page and so cannot compute what the reference
value should be in our tiling selftests. We have to skip the test.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107133
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705171523.18462-1-chris@chris-wilson.co.uk
With the fb-helper no longer relying on the non-atomic .best_encoder()
we can eliminate the hook from the MST encoder.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628131315.14156-3-ville.syrjala@linux.intel.com
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 141432
Addresses-Coverity-ID: 141433
Addresses-Coverity-ID: 141434
Addresses-Coverity-ID: 141435
Addresses-Coverity-ID: 141436
Addresses-Coverity-ID: 1357360
Addresses-Coverity-ID: 1357403
Addresses-Coverity-ID: 1357433
Addresses-Coverity-ID: 1392622
Addresses-Coverity-ID: 1415273
Addresses-Coverity-ID: 1435752
Addresses-Coverity-ID: 1441500
Addresses-Coverity-ID: 1454596
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628223541.GA17665@embeddedor.com
This patch adds the new registers and corresponding bit definitions
which will be used for programming/enable DSI PLL.
v2: Review comments from Jani N
- Fix spaces while defining ICL_ESC_CLK_DIV_MASK
- Define shift and mask for bitfields.
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530795727-28644-2-git-send-email-madhav.chauhan@intel.com
Commit cd7e 61b9"init mmio by lri command in vgpu inhibit context"
initializes registers saved/restored in context with its vreg value
through lri command in ring buffer. It relies on vreg got updated
on every guest access. There is a case found that Linux guest uses
lri command in inhibit-ctx to update the register. This patch adds
vreg update on this case.
v2: move mmio_attribute functions to gvt.h (Zhenyu)
v3: use mask_mmio_write in vreg update
v4: refine codes and add more comments (Zhenyu)
Fixes: cd7e61b9("drm/i915/gvt: init mmio by lri command in vgpu inhibit context")
Signed-off-by: Hang Yuan <hang.yuan@linux.intel.com>
Signed-off-by: Weinan Li <weinan.z.li@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Currently, the wc-stash used for providing flushed WC pages ready for
constructing the page directories is assumed to be protected by the
struct_mutex. However, we want to remove this global lock and so must
install a replacement global lock for accessing the global wc-stash (the
per-vm stash continues to be guarded by the vm).
We need to push ahead on this patch due to an oversight in hastily
removing the struct_mutex guard around the igt_ppgtt_alloc selftest. No
matter, it will prove very useful (i.e. will be required) in the near
future.
v2: Restore the onstack stash so that we can drop the vm->mutex in
future across the allocation.
v3: Restore the lost pagevec_init of the onstack allocation, and repaint
function names.
v4: Reorder init so that we don't try and use i915_address_space before
it is ininitialised.
Fixes: 1f6f00238a ("drm/i915/selftests: Drop struct_mutex around lowlevel pggtt allocation")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180704185518.4193-1-chris@chris-wilson.co.uk
Adjust the EIR clearing to cope with the edge triggered IIR
on i965/g4x. To guarantee an edge in the ISR master error bit
we temporarily mask everything in EMR. As some of the EIR bits
can't even be directly cleared we also borrow a trick from
i915_clear_error_registers() and permanently mask any bit that
remains high. No real thought given to how we might unmask them
again once the cause for the error has been clered. I suppose
on pre-g4x GPU reset will reinitialize EMR from scratch.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611200258.27121-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Just like with PIPESTAT, the edge triggered IIR on i965/g4x
also causes problems for hotplug interrupts. To make sure
we don't get the IIR port interrupt bit stuck low with the
ISR bit high we must force an edge in ISR. Unfortunately
we can't borrow the PIPESTAT trick and toggle the enable
bits in PORT_HOTPLUG_EN as that act itself generates hotplug
interrupts. Instead we just have to loop until we've cleared
PORT_HOTPLUG_STAT, or we just give up and WARN.
v2: Don't frob with PORT_HOTPLUG_EN
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614175625.1615-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Two requests have come in for a backmerge,
and I've got some pull reqs on rc2, so this
just makes sense.
Signed-off-by: Dave Airlie <airlied@redhat.com>
For a ppgtt that we are constructing, there is no struct_mutex
dependence so skip it. In the process, also ping the scheduler
frequently to try and avoid the NMI watchdog.
v2: gen6 requires struct_mutex to clean up (currently)
Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=107094
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180703135331.12265-1-chris@chris-wilson.co.uk
live_gtt is a very slow test to run, simply because it tries to allocate
and use as much as the 48b address space as possibly can and in the
process will try to own all of the system memory. This leads to resource
exhaustion and CPU starvation; the latter impacts us when the NMI
watchdog declares a task hung due to a mutex contention with ourselves.
This we can prevent by releasing the struct_mutex and forcing our
i915/rcu workers to run, and in particular flushing the freed object
worker that is the cause for concern.
References: https://bugs.freedesktop.org/show_bug.cgi?id=107094
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180703101829.7360-1-chris@chris-wilson.co.uk
If the whole object is already pinned by HW for use as scanout, we will
fail to move it to the mappable region and so must resort to using a
partial VMA covering the whole object.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104513
Fixes: aa136d9d72 ("drm/i915: Convert partial ggtt vma to full ggtt if it spans the entire object")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180630090509.469-1-chris@chris-wilson.co.uk
(cherry picked from commit 7e7367d3bc)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The PIPEDSL freezes on PSR entry and if PSR hasn't fully exited, then
the pipe_update_start call schedules itself out to check back later.
On ChromeOS-4.4 kernel, which is fairly up-to-date w.r.t drm/i915 but
lags w.r.t core kernel code, hot plugging an external display triggers
tons of "potential atomic update errors" in the dmesg, on *pipe A*. A
closer analysis reveals that we try to read the scanline 3 times and
eventually timeout, b/c PSR hasn't exited fully leading to a PIPEDSL
stuck @ 1599. This issue is not seen on upstream kernels, b/c for *some*
reason we loop inside intel_pipe_update start for ~2+ msec which in this
case is more than enough to exit PSR fully, hence an *unstuck* PIPEDSL
counter, hence no error. On the other hand, the ChromeOS kernel spends
~1.1 msec looping inside intel_pipe_update_start and hence errors out
b/c the source is still in PSR.
Regardless, we should wait for PSR exit (if PSR is disabled, we incur
a ~1-2 usec penalty) before reading the PIPEDSL, b/c if we haven't
fully exited PSR, then checking for vblank evasion isn't actually
applicable.
v4: Comment explaining psr_wait after enabling VBL interrupts (DK)
v5: CAN_PSR() to handle platforms that don't support PSR.
v6: Handle local_irq_disable on early return (Chris)
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Tarun Vyas <tarun.vyas@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627200250.1515-2-tarun.vyas@intel.com
This is a lockless version of the exisiting psr_wait_for_idle().
We want to wait for PSR to idle out inside intel_pipe_update_start.
At the time of a pipe update, we should never race with any psr
enable or disable code, which is a part of crtc enable/disable.
The follow up patch will use this lockless wait inside pipe_update_
start to wait for PSR to idle out before checking for vblank evasion.
We need to keep the wait in pipe_update_start to as less as it can be.
So,we can live and flourish w/o taking any psr locks at all.
Even if psr is never enabled, psr2_enabled will be false and this
function will wait for PSR1 to idle out, which should just return
immediately, so a very short (~1-2 usec) wait for cases where PSR
is disabled.
v2: Add comment to explain the 25msec timeout (DK)
v3: Rename psr_wait_for_idle to __psr_wait_for_idle_locked to avoid
naming conflicts and propagate err (if any) to the caller (Chris)
v5: Form a series with the next patch
v7: Better explain the need for lockless wait and increase the max
timeout to handle refresh rates < 60 Hz (Daniel Vetter)
v8: Rebase
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Tarun Vyas <tarun.vyas@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627200250.1515-1-tarun.vyas@intel.com
Prints live state of psr1.Extending the existing
PSR2 live state function to cover psr1.
Tested on KBL with psr2 and psr1 panel.
v2: rebase
v3: DK
Rename psr2_live_status to psr_source_status.
v4: DK
Move EDP_PSR_STATUS_STATE_SHIFT below EDP_PSR_STATUS_STATE_MASK.
Pass seq to psr_source_status, handle source status prints in
psr_source_status.
v5: Fixed CI warning messages
v6:
Remove extra space in the title before the colon.(DK)
Rebase. (Jani)
v7: Use tabs for indenting the values.(Jani)
v8: Addressed dk's review comments.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530086910-15914-1-git-send-email-vathsala.nagaraju@intel.com
If the whole object is already pinned by HW for use as scanout, we will
fail to move it to the mappable region and so must resort to using a
partial VMA covering the whole object.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104513
Fixes: aa136d9d72 ("drm/i915: Convert partial ggtt vma to full ggtt if it spans the entire object")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180630090509.469-1-chris@chris-wilson.co.uk
changed gvt display transcode DDI mode from DP_SST to
DVI to address below calltrace issue during guest booting
up which is caused by zero dotclock initial value with DP_SST
mode. transcode DVI mode emulation also align with native with DP
connection.
[drm:drm_calc_timestamping_constants]
ERROR crtc 41: Can't calculate constants, dotclock = 0!
WARNING: at drivers/gpu/drm/drm_vblank.c:620
drm_calc_vbltimestamp_from_scanoutpos
Call Trace:
? drm_calc_timestamping_constants+0x144/0x150 [drm]
drm_get_last_vbltimestamp+0x54/0x90 [drm]
drm_reset_vblank_timestamp+0x59/0xd0 [drm]
drm_crtc_vblank_on+0x7b/0xd0 [drm]
intel_modeset_setup_hw_state+0xb67/0xfd0 [i915]
? gen2_read32+0x110/0x110 [i915]
? drm_modeset_lock+0x30/0xa0 [drm]
intel_modeset_init+0x794/0x19d0 [i915]
? intel_setup_gmbus+0x232/0x2e0 [i915]
i915_driver_load+0xb4a/0xf40 [i915]
Signed-off-by: Xiaolin Zhang <xiaolin.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
when guest writes ggtt entries, it could write 8 bytes a time if
gtt_entry_size is 8. But, qemu could split the 8 bytes into 2 consecutive
4-byte writes.
If each 4-byte partial write could trigger a host ggtt write, it is very
possible that a wrong combination is written to the host ggtt. E.g.
the higher 4 bytes is the old value, but the lower 4 bytes is the new
value, and this 8-byte combination is wrong but written to the ggtt, thus
causing bugs.
To handle this condition, we just record the first 4-byte write, then wait
until the second 4-byte write comes and write the combined 64-bit data to
host ggtt table.
To save memory space and to spot partial write as early as possible, we
don't keep this information for every ggtt index. Instread, we just record
the last ggtt write position, and assume the two 4-byte writes come in
consecutively for each vgpu.
This assumption is right based on the characteristic of ggtt entry which
stores memory address. When gtt_entry_size is 8, the guest memory physical
address should be 64 bits, so any sane guest driver should write 8-byte
long data at a time, so 2 consecutive 4-byte writes at the same ggtt index
should be trapped in gvt.
v2:
when incomplete ggtt entry write is located, e.g.
1. guest only writes 4 bytes at a ggtt offset and no long writes the
rest 4 bytes.
2. guest writes 4 bytes of a ggtt offset, then write at other ggtt
offsets, then return back to write the left 4 bytes of the first
ggtt offset.
add error handling logic to remap host entry to scratch page, and mark
guest virtual ggtt entry as not present. (zhenyu wang)
Signed-off-by: Zhao Yan <yan.y.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=0uqV
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20180629' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Small set of fixes for this series. Mostly just minor fixes, the only
oddball in here is the sg change.
The sg change came out of the stall fix for NVMe, where we added a
mempool and limited us to a single page allocation. CONFIG_SG_DEBUG
sort-of ruins that, since we'd need to account for that. That's
actually a generic problem, since lots of drivers need to allocate SG
lists. So this just removes support for CONFIG_SG_DEBUG, which I added
back in 2007 and to my knowledge it was never useful.
Anyway, outside of that, this pull contains:
- clone of request with special payload fix (Bart)
- drbd discard handling fix (Bart)
- SATA blk-mq stall fix (me)
- chunk size fix (Keith)
- double free nvme rdma fix (Sagi)"
* tag 'for-linus-20180629' of git://git.kernel.dk/linux-block:
sg: remove ->sg_magic member
drbd: Fix drbd_request_prepare() discard handling
blk-mq: don't queue more if we get a busy return
block: Fix cloning of requests with a special payload
nvme-rdma: fix possible double free of controller async event buffer
block: Fix transfer when chunk sectors exceeds max
While debugging we may want to examine params passed to GuC.
v2: drop #ifdef DEBUG_GUC - Michal
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> #1
Cc: Michal Winiarski <michal.winiarski@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618111821.47088-1-michal.wajdeczko@intel.com
make_obj_busy() makes a dummy busy object, but didn't attach the fence
to the reservation object, so it would not have registered as busy. For
completeness, attach the dummy request as the exclusive fence and mark
the object as written (in i915_vma_move_to_active)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180629133717.11761-2-chris@chris-wilson.co.uk
We correctly attach the exclusive fetch for the scratch object when
emitting a request that writes into it, but for completeness we should
also declared the write to i915_vma_move_to_active()
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180629133717.11761-1-chris@chris-wilson.co.uk
This was introduced more than a decade ago when sg chaining was
added, but we never really caught anything with it. The scatterlist
entry size can be critical, since drivers allocate it, so remove
the magic member. Recently it's been triggering allocation stalls
and failures in NVMe.
Tested-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The only time we should start FBC is when we have waited a vblank
after the atomic update. We've already forced a vblank wait by doing
wait_for_flip_done before intel_post_plane_update(), so we don't need
to wait a second time before enabling.
Removing the worker simplifies the code and removes possible race
conditions, like happening in 103167.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103167
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625163758.10871-2-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Ville Syrjälä