Commit Graph

243830 Commits

Author SHA1 Message Date
Ido Yariv d2f4d47d84 wl12xx: Simplify TX blocks accounting
The total number of TX memory blocks may change when the dynamic memory
option is enabled. The current implementation only tracks the available
memory blocks, which over-complicates TX blocks accounting.

By tracking the number of allocated blocks, calculation of the number of
available blocks becomes simpler and cleaner. It simply equals the total
number of TX memory blocks minus the allocated ones.

Also, remove some unnecessary castings and use union member accesses
instead.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:20 +03:00
Ido Yariv 990f5de738 wl12xx: Clean up the dummy packet mechanism
The current implementation allocates a skb each time one is requested by
the firmware. Since dummy packets are handled differently than regular
packets, the skb needs to be marked. Currently, this is done by
setting the pkt_type member to 5. This might not be safe, as we cannot
be sure that there won't be any other packets with this pkt_type value.

Since the packet does not change from one request to another, we can
simply allocate a dummy packet template and always send it. All changes
to the skb done during packet preparation must be reverted, so the same
skb can be reused.

The dummy packets are not transmitted, therefore there's no need to set
the BSSID or our own MAC address.

In addition, the header portion of the packet was zeroed by mistake, so
fix that as well.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:19 +03:00
Ido Yariv 0da13da767 wl12xx: Clean up the block size alignment code
Simplify and clean up the block size alignment code:
1. Set the block size according to the padding field type, as it cannot
   exceed the maximum value this field can hold.
2. Move the alignment code into a function instead of duplicating it in
   multiple places.
3. In the current implementation, the block_size member can be
   misleading because a zero value actually means that there's no need to
   align. Declare a block size alignment quirk instead.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:18 +03:00
Ido Yariv d29633b40e wl12xx: Clean up and fix the 128x boot sequence
Clean up the boot sequence code & fix the following issues:
1. Always read the registers' values and set the relevant bits instead of
   zeroing all other bits
2. Handle cases where wl1271_top_reg_read returns an error
3. Verify that the HW can detect the selected clock source
4. Remove 128x PG10 initialization code
5. Configure the MCS PLL to work in HP mode

Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:17 +03:00
Ohad Ben-Cohen 8bf69aae4c wl12xx: fix "JOIN while associated" commentary
Issuing multiple JOIN commands to the wl12xx's firmware, while
we're associated, might have undesired implications, so the driver
prints a message when that happens, and warn developers who check
out the source.

Update the commentary in order to consider the one valid scenario
where this can happen: roaming.

Cautiously keep the message for now, until we either gain confidence
there are no unintentional JOIN-while-associated events, or until
we move to the new multi-role fw who solves this multiple-join issue
for good.

Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:16 +03:00
Ohad Ben-Cohen c5745187a4 wl12xx: fix roaming
The wl12xx device normally drops all frames coming from BSSID
it is not joined with.

This behavior is configured today by the wl12xx driver in response
to a handful of ieee80211_bss_change and ieee80211_conf_changed
notification flags, such as BSS_CHANGED_ASSOC, BSS_CHANGED_BSSID,
IEEE80211_CONF_CHANGE_IDLE, etc..

This breaks when we roam to a new BSSID, where authentication frames
are sent before any BSS_CHANGED/CONF_CHANGED flags are received.
When this happens the hardware silently drops the authentication
responses, and the roaming fails.

Ideally this aggressive filtering behavior of the device should be disabled
upon a notification from mac80211. Such notification will take place
after multi-channel support will be added: mac80211 will likely send a
remain-on-channel notification to drivers when entering sensitive
states (like authentication), otherwise the firmware might jump to
different channels (to serve a different role).

Until those notifications materialize, disable the hw BSSID filter
when authentication requests are sent, so roaming would work.

Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:15 +03:00
Juuso Oikarinen 13026decf7 wl12xx: Handle duplicate calling of remove interface
Because of the hardware recovery mechanism, its possible the
__wl1271_op_remove_interface is called twice. Currently, this leads to a
kernel crash even before a kernel WARNing can be issued.

Fix this.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:15 +03:00
Eliad Peller c1b193eb65 wl12xx: rearrange some ELP wake_up/sleep calls
ELP (Extremely/Enhanced Low Power, or something like that ;)) refers to
the powerstate of the 12xx chip, in which very low power is consumed,
and no commands (from the host) can be issued until the chip is woken up.

Wakeup/sleep commands must be protected by a wl->mutex, so it's generally
a good idea to call wakeup/sleep along with the mutex lock/unlock (where
needed). However, in some places the wl12xx driver calls wakeup/sleep in
some "inner" functions. This result in some "nested" wakeup/sleep calls
which might end up letting the chip go to sleep prematurely (e.g. during
event handling).

Fix it by rearranging the elp calls to come along with mutex_lock/unlock.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:14 +03:00
Arik Nemtsov 17e672d6e4 wl12xx: configure channel/band while FW is off
Initialize the channel and band from mac80211 conf even when the FW is
not yet loaded. This mitigates a bug in AP-mode where the channel was
never changed from its initial setting after FW boot and was therefore
never configured to FW.

Reported-by: Alexander Boukaty <alexanderb@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:13 +03:00
Luciano Coelho 4a31c11c7d wl12xx: use a bitmask instead of list of booleans in scanned_ch
We were using an array of booleans to mark the channels we had already
scanned.  This was causing a sparse error, because bool is not a type
with defined size.  To fix this, use bitmasks instead, which is much
cleaner anyway.

Thanks Johannes Berg for the idea.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:12 +03:00
Luciano Coelho 4623ec7d97 wl12xx: fix a couple of sparse warnings about undeclared functions
Fix the following sparse warnings:

drivers/net/wireless/wl12xx/main.c:1129:5: warning: symbol '__wl1271_plt_stop' was not declared. Should it be static?
drivers/net/wireless/wl12xx/main.c:2988:5: warning: symbol 'wl1271_op_ampdu_action' was not declared. Should it be static?

Both functions should be static.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:11 +03:00
Luciano Coelho d9482e2b51 wl12xx: fix SG BT load value to reflect its new meaning
The Soft Gemini BT load ratio value has changed its meaning with FW
version 6.1.0.0.310.  It now means the passive scan compensation
percentage during A2DP EDR.  Instead of 50, we need to use 200.

Fix the SG configuration accordingly.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:10 +03:00
Luciano Coelho 18b92ffaf3 wl12xx: set the skbuff priority for dummy packets
The firmware requires dummy packets to be sent using TID 7
(WL1271_TID_MGMT).  Instead of hardcoding it in the tx_fill_hdr()
function, set it when creating the packet itself.

This requires Eliad's fix to set the actual TID in the TX descriptor.

Cc: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:09 +03:00
Eliad Peller db674d249c wl12xx: set the actual tid instead of the ac
When passing a tx frame, the driver incorrectly set desc->tid
with the ac instead of the actual tid.

It has some serious implications when using 802.11n + QoS,
as the fw starts a BlockAck with the wrong tid (which finally
cause beacon loss and disconnection / some fw crash)

Fix it by using the actual tid stored in skb->priority.

Reported-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:08 +03:00
Juuso Oikarinen f9f774c17e wl12xx: Add mutex protection for interface list
The interface list maintained in main.c is not mutex protected. This could
cause issues, as the list is accessed from notifier chains.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:08 +03:00
Arik Nemtsov 1d732e8cf3 wl12xx: Clamp byte mode transfers for 128x chips
On wl128x based devices, when TX packets are aggregated, each packet
size must be aligned to the SDIO block size, and sent using block mode
transfers.

The block size is set to 256 bytes, which is less than the maximum
possible byte transfer. Thus, if two small packets (< 256 bytes) are
aggregated, the aggregation buffer size would be 512, and will be sent
using byte mode transfers. This can have undesired side effects.

Fix this by setting the MMC_QUIRK_BLKSZ_FOR_BYTE_MODE mmc card quirk.
For 127x chips this has no effect, as the block size is set to 512
bytes.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:07 +03:00
Ohad Ben-Cohen 958b20e068 wl12xx: update bet_max_consecutive
Allow early termination of 50 consecutive beacons.

This value is the recommended one by the 12xx's system/RF team,
and tests show that power consumption is improved as expected.

Reported-by: Ruthy Zaphir <ruthyz@ti.com>
Tested-by: Danil Shalumov <danils@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:06 +03:00
Shahar Levi 871d0c3ba3 wl12xx: Add support for 11n Rx STBC one spatial stream
The wl12xx chip supports one Rx STBC spatial stream.  Announce this in
the HT capabilities info field.

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:05 +03:00
Juuso Oikarinen 0af0467f09 wl12xx: Fix potential incorrect band in rx-status
The rx-status passed to mac80211 along with each received frame contains the
band on which the frame was received. Under certain circumstances, this band
information may be incorrect, causing in worst case a WARNING from mac80211,
and causes the received frame to be dropped.

This scenario mainly occurs when performing connected-mode scans, when the
received scan results are from the other band than the one currently
associated to.

[Since desc_band doesn't exist anymore, use status->band in the later
call to ieee80211_channel_to_frequency() to fix compilation -- Luca]

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:04 +03:00
Luciano Coelho e7ddf549f3 wl12xx: use 1 spare TX block instead of two
All the new firmware versions (>=6.1.3.50.58 for STA and >=6.2.0.0.47
for AP) use 1 spare TX block.  We still want to support older
firmwares that require 2 spare blocks, so added a quirk to handle the
difference.

Also implemented a generic way of setting quirks that depend on the
firmware revision.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:03 +03:00
Shahar Levi 0830ceedbf wl12xx: 1281/1283 support - enable chip support
Add support to wl128x chip via chip id

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:03 +03:00
Arik Nemtsov 1aed55fd78 wl12xx: 1281/1283 support - Use different FW file for AP mode wl127x/wl128x chips
Choose a different FW for AP-mode wl127x and wl128x chips, base on chip
ID at boot time.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:02 +03:00
Shahar Levi ae47c45fd0 wl12xx: 1281/1283 support - Add dummy packet support
Support sending dummy packet to wl128x FW as results of
dummy packet event. That is part of dynamic TX mem blocks mechanism.

Only send dummy packet when not in AP mode.

[Even though the DUMMY_PACKET_EVENT_ID and the
STA_REMOVE_COMPLETE_EVENT_ID events are defined to the same value, we
need to treat them separately in the code.  Keep the check and enable
STA_REMOVE_COMPLETE_EVENT_ID for AP mode and DUMMY_PACKET_EVENT_ID for
STA.  Moved one warning to a cleaner place.  Use WL1271_TID_MGMT for
dummy packets -- Luca]

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:01 +03:00
Shahar Levi ae77eccf04 wl12xx: 1281/1283 support - Improve Tx & Rx path
Reduced bus transactions in the Tx & Rx path.

[Removed unnecessary check wl->chip.id != CHIP_ID_1283_PG20 when
checking the quirk -- Luca]

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:00 +03:00
Shahar Levi 13b107dd98 wl12xx: 1281/1283 support - use dynamic memory for the RX/TX pools
Separate the memory configuration to chip-specific structures and
implement dynamic memory for wl128x.

This feature allows us to move TX memory blocks to the RX pool when
the RX path is overloaded.

Thanks for Arik Nemtsov <arik@wizery.com> for helping simplify the
wl1271_fw_status() code.

[Rewrote the commit subject and message for clarity; improved some
comments and changed "spare" to "padding" for consistency; added a
FIXME for the AP memory configuration -- Luca]

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:48:59 +03:00
Shahar Levi 5ea417ae77 wl12xx: 1281/1283 support - New boot sequence
Boot sequence support FREF clock and TCXO clock.
WL128x has two clocks input - TCXO and FREF.
TCXO is the main clock of the device, while FREF is used to sync
between the GPS and the cellular modem.
Auto-detection checks where TCXO is 32.736MHz or 16.368MHz, in that
case the FREF will be used as the WLAN/BT main clock.

[Use clock enumeration as defined in linux/wl12xx.h; remove
unnecessary else block in wl128x_switch_fref; remove unnecessary
change in main.c; remove some unnecessary debug prints and comments;
fix potential use of uninitialized value (pll_config) -- Luca]

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:48:58 +03:00
Shahar Levi bc765bf3b9 wl12xx: 1281/1283 support - Loading FW & NVS
Take care of FW & NVS with the auto-detection between wl127x and
wl128x.

[Moved some common code outside if statements and added notes about
NVS structure assumptions; Fixed a bug when checking the nvs size: if
the size was incorrect, the local nvs variable was set to NULL, it
should be wl->nvs instead. -- Luca]

[Merged with potential buffer overflow fix -- Luca]

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:48:10 +03:00
Shahar Levi 49d750ca14 wl12xx: 1281/1283 support - New radio structs and functions
New general and radio parameters structures and functions.
Implemented as separate functions due to auto-detection
between wl127x and wl128x.

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:19:48 +03:00
Luciano Coelho a81159edf8 wl12xx: 1281/1283 support - add block size handling for sdio and spi
Add the the set_block_size op in the SDIO and in the SPI modules.
Since it is only used with SDIO, just explicitly set the op to NULL in
spi.c

Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:19:48 +03:00
Shahar Levi 48a61477bd wl12xx: 1281/1283 support - Add acx commands
New acx command that sets: Rx fifo enable reduced bus transactions
in RX path. Tx bus transactions padding to SDIO block size that
improve preference in Tx and essential for working with SDIO HS (48Mhz).
The max SDIO block size is 256 when working with Tx bus transactions
padding to SDIO block.

Add new ops to SDIO & SPI that handles the win size change in case of
transactions padding (relevant only for SDIO).

[Fix endianess issues; simplify sdio-specific block_size handling;
minor changes in comments; use "aligned_len" in one calculation
instead of "pad" to avoid confusion -- Luca]

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:19:47 +03:00
Shahar Levi 5aa42346bb wl12xx: 1281/1283 support - Add Definitions
Definitions to support wl128x:
  - New FW file name
  - Chip ID
  - New PLL Configuration Algorithm macros that will be used at wl128x
    boot stage
  - Rename NVS macro name: wl127x and wl128x are using the same NVS
    file name. However, the ini parameters between them are
    different. The driver will validate the correct NVS size in
    wl1271_boot_upload_nvs().

[Cleaned up some of the definitions. -- Luca]

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:19:46 +03:00
Shahar Levi b9b0fdead0 wl12xx: 1281/1283 support - move IRQ polarity
In order to prevent overran of IRQ polarity via FW the polarity setting move after
FW download and before IRQ enable.

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:19:45 +03:00
Luciano Coelho 62c7d085e1 wl12xx: add new board_tcxo_clock element to the platform data
This new value is a new type of clock setting that is used by wl128x
chipsets.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:19:44 +03:00
Senthil Balasubramanian 34a0a2025c ath: Add a missing world regulatory domain 0x6C
Some customers use 0x6C world regulatory domain and this patch
adds the support.

Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-14 15:35:14 -04:00
Larry Finger 9f219bd248 rtlwifi: Fix unitialized variable warnings
In http://lkml.indiana.edu/hypermail/linux/kernel/1104.1/01955.html, Geerti
Uytterhoeven reports the following warnings for the rtlwifi drivers.

src/drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c: warning:
	 'cck_index' may be used uninitialized in this function: => 637
src/drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c: warning:
	 'cck_index_old' may be used uninitialized in this function: => 637
src/drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c: warning:
	 'box_extreg' may be used uninitialized in this function: => 303
src/drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c: warning:
	 'box_reg' may be used uninitialized in this function: => 303
src/drivers/net/wireless/rtlwifi/rtl8192ce/rf.c: warning:
	 'chnlgroup' may be used uninitialized in this function: => 205
src/drivers/net/wireless/rtlwifi/rtl8192ce/rf.c: warning:
	 'u4_regvalue' may be used uninitialized in this function: => 450
src/drivers/net/wireless/rtlwifi/rtl8192cu/hw.c: warning:
	 'hq_sele' may be used uninitialized in this function: => 924

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-14 15:35:14 -04:00
Bing Zhao 53d7938e6a mwifiex: rename function mwifiex_is_ba_stream_avail
The old function name sounds like checking for existing BA
stream. The function actually checks if we have room for
creating new BA stream or not.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-14 15:35:13 -04:00
Amitkumar Karwar 572e8f3ead mwifiex: remove unused function parameters
Some function parameters become useless after previous
cleanup changes.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-14 15:35:13 -04:00
Yogesh Ashok Powar 19a898601a mwifiex: remove redundant "return" at end of void function
The return statement at the last line of a void function
is not necessary.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-14 15:35:12 -04:00
Amitkumar Karwar 600f5d909a mwifiex: cleanup ioctl wait queue and abstraction layer
1) remove mwifiex_alloc_fill_wait_queue() and
mwifiex_request_ioctl()
2) avoid dynamic allocation of wait queue
3) remove unnecessary mwifiex_error_code macros that
were used mainly by the wait queue status code
4) remove some abstraction functions
5) split mwifiex_prepare_cmd() to mwifiex_send_cmd_async()
and mwifiex_send_sync() to handle asynchronous and
synchronous commands respectively

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-14 15:35:11 -04:00
Felix Fietkau 3a9dddea89 ath5k: disable 5 GHz support for the dualband PHY chip on dual-radio AR5312
There are two variants of AR5312 dual-band devices, one single-radio
and the other one dual-radio. On the dual-radio board, the first MAC
only supports 5 GHz, even though it has a dual-band PHY. The 2.4 GHz
part of this phy is used in pass-through mode, connecting the second
MAC with the second PHY.
Disable 2.4 GHz for the first MAC on an AR5312, but only if the board
configuration indicates a dual-radio device.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-14 15:35:10 -04:00
Felix Fietkau 32377b6cf7 ath5k: fix the EEPROM check for hw AES crypto support
EEPROM version 5.0 adds a new field for disabling AES support, having
an older version means that AES is present. This patch fixes hw AES
crypto support on AR5312 boards, which have an older EEPROM version.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-14 15:35:09 -04:00
Felix Fietkau fa9bfd61e0 ath5k: add a new bus op for reading the mac address
On AHB, the calibration data usually does not contain a valid MAC address,
the correct MAC address is stored in the board config.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-14 15:35:09 -04:00
Felix Fietkau 0cb9e06b63 ath: unshare struct ath_bus_ops between ath5k and ath9k
This struct is not used in any common code, and moving it out of
the ath header makes it easier to add more driver specific ops.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-14 15:35:08 -04:00
Felix Fietkau 7f94f05b24 ath5k: disable 5 GHz support if a 2.4 GHz radio is detected
On a dual-radio dual-band AR5312 device, the calibration data is shared
between the 5 GHz and the 2.4 GHz radio/MAC.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-14 15:35:08 -04:00
Rajkumar Manoharan 10add41f2b ath9k: Fix improper beacon slot selection in IBSS
Request a re-configuration of Beacon related timers
on the receipt of the first Beacon frame has to be set only
for station mode. Setting beacon sync for IBSS is causing
wrong beacon slot selection on beacon generation.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-14 15:35:07 -04:00
John W. Linville dfa8fc69d9 ath9k: avoid using trinary operator w/ TX_STAT_INC
Otherwise, you get this:

  CC [M]  drivers/net/wireless/ath/ath9k/hif_usb.o
drivers/net/wireless/ath/ath9k/hif_usb.c: In function ‘ath9k_skb_queue_complete’:
drivers/net/wireless/ath/ath9k/hif_usb.c:230:12: error: expected expression before ‘do’
make[2]: *** [drivers/net/wireless/ath/ath9k/hif_usb.o] Error 1
make[1]: *** [drivers/net/wireless/ath/ath9k] Error 2
make: *** [drivers/net/wireless/ath/] Error 2

The TX_STAT_INC macro should probably be changed to accomodate such
usage, although using a trinary operator in place of an if-else seems
questionable to me anyway.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@Atheros.com>
2011-04-14 15:29:06 -04:00
cozybit Inc a3e6b12c02 mac80211: Allocate new mesh path and portal tables before taking locks
It is unnecessary to hold the path table resize lock while allocating a
new table.  Allocate first and take lock later.  This resolves a
soft-lockup:

[  293.385799] BUG: soft lockup - CPU#0 stuck for 61s! [kworker/u:3:744]
(...)
[  293.386049] Call Trace:
[  293.386049]  [<c119fd04>] do_raw_read_lock+0x26/0x29
[  293.386049]  [<c14b2982>] _raw_read_lock+0x8/0xa
[  293.386049]  [<c148c178>] mesh_path_add+0xb7/0x24e
[  293.386049]  [<c148b98d>] ? mesh_path_lookup+0x1b/0xa6
[  293.386049]  [<c148ded5>] hwmp_route_info_get+0x276/0x2fd
[  293.386049]  [<c148dfb6>] mesh_rx_path_sel_frame+0x5a/0x5d9
[  293.386049]  [<c102667d>] ? update_curr+0x1cf/0x1d7
[  293.386049]  [<c148b45a>] ieee80211_mesh_rx_queued_mgmt+0x60/0x67
[  293.386049]  [<c147c374>] ieee80211_iface_work+0x1f0/0x258
(...)

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-13 15:24:48 -04:00
Sujith Manoharan 09d5b94d2c ath9k_htc: Enable AP and P2P modes
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-13 15:24:44 -04:00
Sujith Manoharan fbc29d6c3d ath9k_htc: Add detailed firmware statistics
New debugfs files:

<debugfs_root>/ath9k_htc/<phy#>/tgt_int_stats
<debugfs_root>/ath9k_htc/<phy#>/tgt_tx_stats
<debugfs_root>/ath9k_htc/<phy#>/tgt_rx_stats

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-13 15:24:41 -04:00
Sujith Manoharan 821f9414c0 ath9k_htc: Use helper routines for transmission
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-13 15:24:37 -04:00