The audit record backlog queue has always been a bit of a mess, and
the moving the multicast send into kauditd_thread() from
audit_log_end() only makes things worse. This patch attempts to fix
the backlog queue with a better design that should hold up better
under load and have less of a performance impact at syscall
invocation time.
While it looks like there is a log going on in this patch, the main
change is the move from a single backlog queue to three queues:
* A queue for holding records generated from audit_log_end() that
haven't been consumed by kauditd_thread() (audit_queue).
* A queue for holding records that have been sent via multicast but
had a temporary failure when sending via unicast and need a resend
(audit_retry_queue).
* A queue for holding records that haven't been sent via unicast
because no one is listening (audit_hold_queue).
Special care is taken in this patch to ensure that the proper
record ordering is preserved, e.g. we send everything in the hold
queue first, then the retry queue, and finally the main queue.
Signed-off-by: Paul Moore <paul@paul-moore.com>
The audit queue names can be shortened and the record sending
helpers associated with the kauditd task could be named better, do
these small cleanups now to make life easier once we start reworking
the queues and kauditd code.
Signed-off-by: Paul Moore <paul@paul-moore.com>
Sending audit netlink multicast messages is bad for all the same
reasons that sending audit netlink unicast messages is bad, so this
patch reworks things so that we don't do the multicast send in
audit_log_end(), we do it from the dedicated kauditd_thread thread just
as we do for unicast messages.
See the GitHub issues below for more information/history:
* https://github.com/linux-audit/audit-kernel/issues/23
* https://github.com/linux-audit/audit-kernel/issues/22
Signed-off-by: Paul Moore <paul@paul-moore.com>
Make sure everything is initialized before we start the kauditd_thread
and don't emit the "initialized" record until everything is finished.
We also panic with a descriptive message if we can't start the
kauditd_thread.
Signed-off-by: Paul Moore <paul@paul-moore.com>
Richard made this change some time ago but Eric backed it out because
the rest of the supporting code wasn't ready. In order to move the
netlink multicast send to kauditd_thread we need to ensure the
kauditd_thread is always running, so restore commit 6ff5e459 ("audit:
move kaudit thread start from auditd registration to kaudit init").
Signed-off-by: Richard Guy Briggs <rbriggs@redhat.com>
[PM: brought forward and merged based on Richard's old patch]
Signed-off-by: Paul Moore <paul@paul-moore.com>
The build system stopped generating ikconfig.h in v2.6.8. Remove an entry
for it in dontdiff. There's also a reference to it in a small comment.
Remove that comment too, as it is of little help in any case.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull workqueue updates from Tejun Heo:
"Mostly patches to initialize workqueue subsystem earlier and get rid
of keventd_up().
The patches were headed for the last merge cycle but got delayed due
to a bug found late minute, which is fixed now.
Also, to help debugging, destroy_workqueue() is more chatty now on a
sanity check failure."
* 'for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: move wq_numa_init() to workqueue_init()
workqueue: remove keventd_up()
debugobj, workqueue: remove keventd_up() usage
slab, workqueue: remove keventd_up() usage
power, workqueue: remove keventd_up() usage
tty, workqueue: remove keventd_up() usage
mce, workqueue: remove keventd_up() usage
workqueue: make workqueue available early during boot
workqueue: dump workqueue state on sanity check failures in destroy_workqueue()
- New cpufreq driver for Broadcom STB SoCs and a Device Tree binding
for it (Markus Mayer).
- Support for ARM Integrator/AP and Integrator/CP in the generic
DT cpufreq driver and elimination of the old Integrator cpufreq
driver (Linus Walleij).
- Support for the zx296718, r8a7743 and r8a7745, Socionext UniPhier,
and PXA SoCs in the the generic DT cpufreq driver (Baoyou Xie,
Geert Uytterhoeven, Masahiro Yamada, Robert Jarzmik).
- cpufreq core fix to eliminate races that may lead to using
inactive policy objects and related cleanups (Rafael Wysocki).
- cpufreq schedutil governor update to make it use SCHED_FIFO
kernel threads (instead of regular workqueues) for doing delayed
work (to reduce the response latency in some cases) and related
cleanups (Viresh Kumar).
- New cpufreq sysfs attribute for resetting statistics (Markus
Mayer).
- cpufreq governors fixes and cleanups (Chen Yu, Stratos Karafotis,
Viresh Kumar).
- Support for using generic cpufreq governors in the intel_pstate
driver (Rafael Wysocki).
- Support for per-logical-CPU P-state limits and the EPP/EPB
(Energy Performance Preference/Energy Performance Bias) knobs
in the intel_pstate driver (Srinivas Pandruvada).
- New CPU ID for Knights Mill in intel_pstate (Piotr Luc).
- intel_pstate driver modification to use the P-state selection
algorithm based on CPU load on platforms with the system profile
in the ACPI tables set to "mobile" (Srinivas Pandruvada).
- intel_pstate driver cleanups (Arnd Bergmann, Rafael Wysocki,
Srinivas Pandruvada).
- cpufreq powernv driver updates including fast switching support
(for the schedutil governor), fixes and cleanus (Akshay Adiga,
Andrew Donnellan, Denis Kirjanov).
- acpi-cpufreq driver rework to switch it over to the new CPU
offline/online state machine (Sebastian Andrzej Siewior).
- Assorted cleanups in cpufreq drivers (Wei Yongjun, Prashanth
Prakash).
- Idle injection rework (to make it use the regular idle path
instead of a home-grown custom one) and related powerclamp
thermal driver updates (Peter Zijlstra, Jacob Pan, Petr Mladek,
Sebastian Andrzej Siewior).
- New CPU IDs for Atom Z34xx and Knights Mill in intel_idle (Andy
Shevchenko, Piotr Luc).
- intel_idle driver cleanups and switch over to using the new CPU
offline/online state machine (Anna-Maria Gleixner, Sebastian
Andrzej Siewior).
- cpuidle DT driver update to support suspend-to-idle properly
(Sudeep Holla).
- cpuidle core cleanups and misc updates (Daniel Lezcano, Pan Bian,
Rafael Wysocki).
- Preliminary support for power domains including CPUs in the
generic power domains (genpd) framework and related DT bindings
(Lina Iyer).
- Assorted fixes and cleanups in the generic power domains (genpd)
framework (Colin Ian King, Dan Carpenter, Geert Uytterhoeven).
- Preliminary support for devices with multiple voltage regulators
and related fixes and cleanups in the Operating Performance Points
(OPP) library (Viresh Kumar, Masahiro Yamada, Stephen Boyd).
- System sleep state selection interface rework to make it easier
to support suspend-to-idle as the default system suspend method
(Rafael Wysocki).
- PM core fixes and cleanups, mostly related to the interactions
between the system suspend and runtime PM frameworks (Ulf Hansson,
Sahitya Tummala, Tony Lindgren).
- Latency tolerance PM QoS framework imorovements (Andrew
Lutomirski).
- New Knights Mill CPU ID for the Intel RAPL power capping driver
(Piotr Luc).
- Intel RAPL power capping driver fixes, cleanups and switch over
to using the new CPU offline/online state machine (Jacob Pan,
Thomas Gleixner, Sebastian Andrzej Siewior).
- Fixes and cleanups in the exynos-ppmu, exynos-nocp, rk3399_dmc,
rockchip-dfi devfreq drivers and the devfreq core (Axel Lin,
Chanwoo Choi, Javier Martinez Canillas, MyungJoo Ham, Viresh
Kumar).
- Fix for false-positive KASAN warnings during resume from ACPI S3
(suspend-to-RAM) on x86 (Josh Poimboeuf).
- Memory map verification during resume from hibernation on x86 to
ensure a consistent address space layout (Chen Yu).
- Wakeup sources debugging enhancement (Xing Wei).
- rockchip-io AVS driver cleanup (Shawn Lin).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vhxI
-----END PGP SIGNATURE-----
Merge tag 'pm-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"Again, cpufreq gets more changes than the other parts this time (one
new driver, one old driver less, a bunch of enhancements of the
existing code, new CPU IDs, fixes, cleanups)
There also are some changes in cpuidle (idle injection rework, a
couple of new CPU IDs, online/offline rework in intel_idle, fixes and
cleanups), in the generic power domains framework (mostly related to
supporting power domains containing CPUs), and in the Operating
Performance Points (OPP) library (mostly related to supporting devices
with multiple voltage regulators)
In addition to that, the system sleep state selection interface is
modified to make it easier for distributions with unchanged user space
to support suspend-to-idle as the default system suspend method, some
issues are fixed in the PM core, the latency tolerance PM QoS
framework is improved a bit, the Intel RAPL power capping driver is
cleaned up and there are some fixes and cleanups in the devfreq
subsystem
Specifics:
- New cpufreq driver for Broadcom STB SoCs and a Device Tree binding
for it (Markus Mayer)
- Support for ARM Integrator/AP and Integrator/CP in the generic DT
cpufreq driver and elimination of the old Integrator cpufreq driver
(Linus Walleij)
- Support for the zx296718, r8a7743 and r8a7745, Socionext UniPhier,
and PXA SoCs in the the generic DT cpufreq driver (Baoyou Xie,
Geert Uytterhoeven, Masahiro Yamada, Robert Jarzmik)
- cpufreq core fix to eliminate races that may lead to using inactive
policy objects and related cleanups (Rafael Wysocki)
- cpufreq schedutil governor update to make it use SCHED_FIFO kernel
threads (instead of regular workqueues) for doing delayed work (to
reduce the response latency in some cases) and related cleanups
(Viresh Kumar)
- New cpufreq sysfs attribute for resetting statistics (Markus Mayer)
- cpufreq governors fixes and cleanups (Chen Yu, Stratos Karafotis,
Viresh Kumar)
- Support for using generic cpufreq governors in the intel_pstate
driver (Rafael Wysocki)
- Support for per-logical-CPU P-state limits and the EPP/EPB (Energy
Performance Preference/Energy Performance Bias) knobs in the
intel_pstate driver (Srinivas Pandruvada)
- New CPU ID for Knights Mill in intel_pstate (Piotr Luc)
- intel_pstate driver modification to use the P-state selection
algorithm based on CPU load on platforms with the system profile in
the ACPI tables set to "mobile" (Srinivas Pandruvada)
- intel_pstate driver cleanups (Arnd Bergmann, Rafael Wysocki,
Srinivas Pandruvada)
- cpufreq powernv driver updates including fast switching support
(for the schedutil governor), fixes and cleanus (Akshay Adiga,
Andrew Donnellan, Denis Kirjanov)
- acpi-cpufreq driver rework to switch it over to the new CPU
offline/online state machine (Sebastian Andrzej Siewior)
- Assorted cleanups in cpufreq drivers (Wei Yongjun, Prashanth
Prakash)
- Idle injection rework (to make it use the regular idle path instead
of a home-grown custom one) and related powerclamp thermal driver
updates (Peter Zijlstra, Jacob Pan, Petr Mladek, Sebastian Andrzej
Siewior)
- New CPU IDs for Atom Z34xx and Knights Mill in intel_idle (Andy
Shevchenko, Piotr Luc)
- intel_idle driver cleanups and switch over to using the new CPU
offline/online state machine (Anna-Maria Gleixner, Sebastian
Andrzej Siewior)
- cpuidle DT driver update to support suspend-to-idle properly
(Sudeep Holla)
- cpuidle core cleanups and misc updates (Daniel Lezcano, Pan Bian,
Rafael Wysocki)
- Preliminary support for power domains including CPUs in the generic
power domains (genpd) framework and related DT bindings (Lina Iyer)
- Assorted fixes and cleanups in the generic power domains (genpd)
framework (Colin Ian King, Dan Carpenter, Geert Uytterhoeven)
- Preliminary support for devices with multiple voltage regulators
and related fixes and cleanups in the Operating Performance Points
(OPP) library (Viresh Kumar, Masahiro Yamada, Stephen Boyd)
- System sleep state selection interface rework to make it easier to
support suspend-to-idle as the default system suspend method
(Rafael Wysocki)
- PM core fixes and cleanups, mostly related to the interactions
between the system suspend and runtime PM frameworks (Ulf Hansson,
Sahitya Tummala, Tony Lindgren)
- Latency tolerance PM QoS framework imorovements (Andrew Lutomirski)
- New Knights Mill CPU ID for the Intel RAPL power capping driver
(Piotr Luc)
- Intel RAPL power capping driver fixes, cleanups and switch over to
using the new CPU offline/online state machine (Jacob Pan, Thomas
Gleixner, Sebastian Andrzej Siewior)
- Fixes and cleanups in the exynos-ppmu, exynos-nocp, rk3399_dmc,
rockchip-dfi devfreq drivers and the devfreq core (Axel Lin,
Chanwoo Choi, Javier Martinez Canillas, MyungJoo Ham, Viresh Kumar)
- Fix for false-positive KASAN warnings during resume from ACPI S3
(suspend-to-RAM) on x86 (Josh Poimboeuf)
- Memory map verification during resume from hibernation on x86 to
ensure a consistent address space layout (Chen Yu)
- Wakeup sources debugging enhancement (Xing Wei)
- rockchip-io AVS driver cleanup (Shawn Lin)"
* tag 'pm-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (127 commits)
devfreq: rk3399_dmc: Don't use OPP structures outside of RCU locks
devfreq: rk3399_dmc: Remove dangling rcu_read_unlock()
devfreq: exynos: Don't use OPP structures outside of RCU locks
Documentation: intel_pstate: Document HWP energy/performance hints
cpufreq: intel_pstate: Support for energy performance hints with HWP
cpufreq: intel_pstate: Add locking around HWP requests
PM / sleep: Print active wakeup sources when blocking on wakeup_count reads
PM / core: Fix bug in the error handling of async suspend
PM / wakeirq: Fix dedicated wakeirq for drivers not using autosuspend
PM / Domains: Fix compatible for domain idle state
PM / OPP: Don't WARN on multiple calls to dev_pm_opp_set_regulators()
PM / OPP: Allow platform specific custom set_opp() callbacks
PM / OPP: Separate out _generic_set_opp()
PM / OPP: Add infrastructure to manage multiple regulators
PM / OPP: Pass struct dev_pm_opp_supply to _set_opp_voltage()
PM / OPP: Manage supply's voltage/current in a separate structure
PM / OPP: Don't use OPP structure outside of rcu protected section
PM / OPP: Reword binding supporting multiple regulators per device
PM / OPP: Fix incorrect cpu-supply property in binding
cpuidle: Add a kerneldoc comment to cpuidle_use_deepest_state()
..
Pull block layer updates from Jens Axboe:
"This is the main block pull request this series. Contrary to previous
release, I've kept the core and driver changes in the same branch. We
always ended up having dependencies between the two for obvious
reasons, so makes more sense to keep them together. That said, I'll
probably try and keep more topical branches going forward, especially
for cycles that end up being as busy as this one.
The major parts of this pull request is:
- Improved support for O_DIRECT on block devices, with a small
private implementation instead of using the pig that is
fs/direct-io.c. From Christoph.
- Request completion tracking in a scalable fashion. This is utilized
by two components in this pull, the new hybrid polling and the
writeback queue throttling code.
- Improved support for polling with O_DIRECT, adding a hybrid mode
that combines pure polling with an initial sleep. From me.
- Support for automatic throttling of writeback queues on the block
side. This uses feedback from the device completion latencies to
scale the queue on the block side up or down. From me.
- Support from SMR drives in the block layer and for SD. From Hannes
and Shaun.
- Multi-connection support for nbd. From Josef.
- Cleanup of request and bio flags, so we have a clear split between
which are bio (or rq) private, and which ones are shared. From
Christoph.
- A set of patches from Bart, that improve how we handle queue
stopping and starting in blk-mq.
- Support for WRITE_ZEROES from Chaitanya.
- Lightnvm updates from Javier/Matias.
- Supoort for FC for the nvme-over-fabrics code. From James Smart.
- A bunch of fixes from a whole slew of people, too many to name
here"
* 'for-4.10/block' of git://git.kernel.dk/linux-block: (182 commits)
blk-stat: fix a few cases of missing batch flushing
blk-flush: run the queue when inserting blk-mq flush
elevator: make the rqhash helpers exported
blk-mq: abstract out blk_mq_dispatch_rq_list() helper
blk-mq: add blk_mq_start_stopped_hw_queue()
block: improve handling of the magic discard payload
blk-wbt: don't throttle discard or write zeroes
nbd: use dev_err_ratelimited in io path
nbd: reset the setup task for NBD_CLEAR_SOCK
nvme-fabrics: Add FC LLDD loopback driver to test FC-NVME
nvme-fabrics: Add target support for FC transport
nvme-fabrics: Add host support for FC transport
nvme-fabrics: Add FC transport LLDD api definitions
nvme-fabrics: Add FC transport FC-NVME definitions
nvme-fabrics: Add FC transport error codes to nvme.h
Add type 0x28 NVME type code to scsi fc headers
nvme-fabrics: patch target code in prep for FC transport support
nvme-fabrics: set sqe.command_id in core not transports
parser: add u64 number parser
nvme-rdma: align to generic ib_event logging helper
...
- Add additional checks for bad platform data
- Remove bounce buffer in console writer
- Protect read/unlink race with a mutex
- Correctly give up during dump locking failures
- Increase ftrace bandwidth by splitting ftrace buffers per CPU
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=UmFL
-----END PGP SIGNATURE-----
Merge tag 'pstore-v4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
"Improvements and fixes to pstore subsystem:
- add additional checks for bad platform data
- remove bounce buffer in console writer
- protect read/unlink race with a mutex
- correctly give up during dump locking failures
- increase ftrace bandwidth by splitting ftrace buffers per CPU"
* tag 'pstore-v4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
ramoops: add pdata NULL check to ramoops_probe
pstore: Convert console write to use ->write_buf
pstore: Protect unlink with read_mutex
pstore: Use global ftrace filters for function trace filtering
ftrace: Provide API to use global filtering for ftrace ops
pstore: Clarify context field przs as dprzs
pstore: improve error report for failed setup
pstore: Merge per-CPU ftrace records into one
pstore: Add ftrace timestamp counter
ramoops: Split ftrace buffer space into per-CPU zones
pstore: Make ramoops_init_przs generic for other prz arrays
pstore: Allow prz to control need for locking
pstore: Warn on PSTORE_TYPE_PMSG using deprecated function
pstore: Make spinlock per zone instead of global
pstore: Actually give up during locking failure
Merge updates from Andrew Morton:
- various misc bits
- most of MM (quite a lot of MM material is awaiting the merge of
linux-next dependencies)
- kasan
- printk updates
- procfs updates
- MAINTAINERS
- /lib updates
- checkpatch updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (123 commits)
init: reduce rootwait polling interval time to 5ms
binfmt_elf: use vmalloc() for allocation of vma_filesz
checkpatch: don't emit unified-diff error for rename-only patches
checkpatch: don't check c99 types like uint8_t under tools
checkpatch: avoid multiple line dereferences
checkpatch: don't check .pl files, improve absolute path commit log test
scripts/checkpatch.pl: fix spelling
checkpatch: don't try to get maintained status when --no-tree is given
lib/ida: document locking requirements a bit better
lib/rbtree.c: fix typo in comment of ____rb_erase_color
lib/Kconfig.debug: make CONFIG_STRICT_DEVMEM depend on CONFIG_DEVMEM
MAINTAINERS: add drm and drm/i915 irc channels
MAINTAINERS: add "C:" for URI for chat where developers hang out
MAINTAINERS: add drm and drm/i915 bug filing info
MAINTAINERS: add "B:" for URI where to file bugs
get_maintainer: look for arbitrary letter prefixes in sections
printk: add Kconfig option to set default console loglevel
printk/sound: handle more message headers
printk/btrfs: handle more message headers
printk/kdb: handle more message headers
...
Pull irq updates from Thomas Gleixner:
"The irq department provides:
- a major update to the auto affinity management code, which is used
by multi-queue devices
- move of the microblaze irq chip driver into the common driver code
so it can be shared between microblaze, powerpc and MIPS
- a series of updates to the ARM GICV3 interrupt controller
- the usual pile of fixes and small improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
powerpc/virtex: Use generic xilinx irqchip driver
irqchip/xilinx: Try to fall back if xlnx,kind-of-intr not provided
irqchip/xilinx: Add support for parent intc
irqchip/xilinx: Rename get_irq to xintc_get_irq
irqchip/xilinx: Restructure and use jump label api
irqchip/xilinx: Clean up print messages
microblaze/irqchip: Move intc driver to irqchip
ARM: virt: Select ARM_GIC_V3_ITS
ARM: gic-v3-its: Add 32bit support to GICv3 ITS
irqchip/gic-v3-its: Specialise readq and writeq accesses
irqchip/gic-v3-its: Specialise flush_dcache operation
irqchip/gic-v3-its: Narrow down Entry Size when used as a divider
irqchip/gic-v3-its: Change unsigned types for AArch32 compatibility
irqchip/gic-v3: Use nops macro for Cavium ThunderX erratum 23154
irqchip/gic-v3: Convert arm64 GIC accessors to {read,write}_sysreg_s
genirq/msi: Drop artificial PCI dependency
irqchip/bcm7038-l1: Implement irq_cpu_offline() callback
genirq/affinity: Use default affinity mask for reserved vectors
genirq/affinity: Take reserved vectors into account when spreading irqs
PCI: Remove the irq_affinity mask from struct pci_dev
...
Pull timer updates from Thomas Gleixner:
"The time/timekeeping/timer folks deliver with this update:
- Fix a reintroduced signed/unsigned issue and cleanup the whole
signed/unsigned mess in the timekeeping core so this wont happen
accidentaly again.
- Add a new trace clock based on boot time
- Prevent injection of random sleep times when PM tracing abuses the
RTC for storage
- Make posix timers configurable for real tiny systems
- Add tracepoints for the alarm timer subsystem so timer based
suspend wakeups can be instrumented
- The usual pile of fixes and updates to core and drivers"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
timekeeping: Use mul_u64_u32_shr() instead of open coding it
timekeeping: Get rid of pointless typecasts
timekeeping: Make the conversion call chain consistently unsigned
timekeeping_Force_unsigned_clocksource_to_nanoseconds_conversion
alarmtimer: Add tracepoints for alarm timers
trace: Update documentation for mono, mono_raw and boot clock
trace: Add an option for boot clock as trace clock
timekeeping: Add a fast and NMI safe boot clock
timekeeping/clocksource_cyc2ns: Document intended range limitation
timekeeping: Ignore the bogus sleep time if pm_trace is enabled
selftests/timers: Fix spelling mistake "Asyncrhonous" -> "Asynchronous"
clocksource/drivers/bcm2835_timer: Unmap region obtained by of_iomap
clocksource/drivers/arm_arch_timer: Map frame with of_io_request_and_map()
arm64: dts: rockchip: Arch counter doesn't tick in system suspend
clocksource/drivers/arm_arch_timer: Don't assume clock runs in suspend
posix-timers: Make them configurable
posix_cpu_timers: Move the add_device_randomness() call to a proper place
timer: Move sys_alarm from timer.c to itimer.c
ptp_clock: Allow for it to be optional
Kconfig: Regenerate *.c_shipped files after previous changes
...
Pull smp hotplug updates from Thomas Gleixner:
"This is the final round of converting the notifier mess to the state
machine. The removal of the notifiers and the related infrastructure
will happen around rc1, as there are conversions outstanding in other
trees.
The whole exercise removed about 2000 lines of code in total and in
course of the conversion several dozen bugs got fixed. The new
mechanism allows to test almost every hotplug step standalone, so
usage sites can exercise all transitions extensively.
There is more room for improvement, like integrating all the
pointlessly different architecture mechanisms of synchronizing,
setting cpus online etc into the core code"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
tracing/rb: Init the CPU mask on allocation
soc/fsl/qbman: Convert to hotplug state machine
soc/fsl/qbman: Convert to hotplug state machine
zram: Convert to hotplug state machine
KVM/PPC/Book3S HV: Convert to hotplug state machine
arm64/cpuinfo: Convert to hotplug state machine
arm64/cpuinfo: Make hotplug notifier symmetric
mm/compaction: Convert to hotplug state machine
iommu/vt-d: Convert to hotplug state machine
mm/zswap: Convert pool to hotplug state machine
mm/zswap: Convert dst-mem to hotplug state machine
mm/zsmalloc: Convert to hotplug state machine
mm/vmstat: Convert to hotplug state machine
mm/vmstat: Avoid on each online CPU loops
mm/vmstat: Drop get_online_cpus() from init_cpu_node_state/vmstat_cpu_dead()
tracing/rb: Convert to hotplug state machine
oprofile/nmi timer: Convert to hotplug state machine
net/iucv: Use explicit clean up labels in iucv_init()
x86/pci/amd-bus: Convert to hotplug state machine
x86/oprofile/nmi: Convert to hotplug state machine
...
Commit 4bcc595ccd ("printk: reinstate KERN_CONT for printing
continuation lines") allows to define more message headers for a single
message. The motivation is that continuous lines might get mixed.
Therefore it make sense to define the right log level for every piece of
a cont line.
This patch introduces printk_skip_headers() that will skip all headers
and uses it in the kdb code instead of printk_skip_level().
This approach helps to fix other printk_skip_level() users
independently.
Link: http://lkml.kernel.org/r/1478695291-12169-3-git-send-email-pmladek@suse.com
Signed-off-by: Petr Mladek <pmladek@suse.com>
Cc: Joe Perches <joe@perches.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Chris Mason <clm@fb.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: David Sterba <dsterba@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 4bcc595ccd ("printk: reinstate KERN_CONT for printing
continuation lines") added back KERN_CONT message header. As a result
it might appear in the middle of the line when the parts are squashed
via the temporary NMI buffer.
A reasonable solution seems to be to split the text in the NNI temporary
not only by newlines but also by the message headers.
Another solution would be to filter out KERN_CONT when writing to the
temporary buffer. But this would complicate the lockless handling.
Also it would not solve problems with a missing newline that was there
even before the KERN_CONT stuff.
This patch moves the temporary buffer handling into separate function.
I played with it and it seems that using the char pointers make the code
easier to read.
Also it prints the final newline as a continuous line.
Finally, it moves handling of the s->len overflow into the paranoid
check. And allows to recover from the disaster.
Link: http://lkml.kernel.org/r/1478695291-12169-2-git-send-email-pmladek@suse.com
Signed-off-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Chris Mason <clm@fb.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: David Sterba <dsterba@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vsnprintf() adds the trailing '\0' but it does not count it into the
number of printed characters. The result is that there is one byte less
space for the real characters in the buffer.
The broken check for the free space might cause that we will repeatedly
try to print 1 character into the buffer, never reach the full buffer,
and do not count the messages as missed.
Also vsnprintf() returns the number of characters that would be printed
if the buffer was big enough. As a result, s->len might be bigger than
the size of the buffer[*]. And the printk() function might return
bigger len than it really printed. Both problems are fixed by using
vscnprintf() instead.
Note that I though about increasing the number of missed messages even
when the message was shrunken. But it made the code even more
complicated. I think that it is not worth it. Shrunken messages are
usually easy to recognize. And it should be a corner case.
[*] The overflown s->len value is crazy and unexpected. I "made a
mistake" and reported this situation as an internal error when fixed
handling of PR_CONT headers in some other patch.
Link: http://lkml.kernel.org/r/20161208174912.GA17042@linux.suse
Signed-off-by: Petr Mladek <pmladek@suse.com>
CcL Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Chris Mason <clm@fb.com>
Cc: David Sterba <dsterba@suse.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Joe Perches <joe@perches.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Takashi Iwai <tiwai@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since sysctl_hung_task_warnings == -1 is allowed (infinite warnings),
commit 48a6d64eda ("hung_task: allow hung_task_panic when
hung_task_warnings is 0") should decrement it only when it is not -1.
This prevents the kernel from ceasing warnings after the first
4294967295 ;)
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: John Siddle <jsiddle@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vfree() is going to use sleeping lock. Thread stack freed in atomic
context, therefore we must use vfree_atomic() here.
Link: http://lkml.kernel.org/r/1479474236-4139-6-git-send-email-hch@lst.de
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Jisheng Zhang <jszhang@marvell.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Dias <joaodias@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This limitation came with the reason to remove "another way for
malicious code to obscure a compromised program and masquerade as a
benign process" by allowing "security-concious program can use this
prctl once during its early initialization to ensure the prctl cannot
later be abused for this purpose":
http://marc.info/?l=linux-kernel&m=133160684517468&w=2
This explanation doesn't look sufficient. The only thing "exe" link is
indicating is the file, used to execve, which is basically nothing and
not reliable immediately after process has returned from execve system
call.
Moreover, to use this feture, all the mappings to previous exe file have
to be unmapped and all the new exe file permissions must be satisfied.
Which means, that changing exe link is very similar to calling execve on
the binary.
The need to remove this limitations comes from migration of NFS mount
point, which is not accessible during restore and replaced by other file
system. Because of this exe link has to be changed twice.
[akpm@linux-foundation.org: fix up comment]
Link: http://lkml.kernel.org/r/20160927153755.9337.69650.stgit@localhost.localdomain
Signed-off-by: Stanislav Kinsburskiy <skinsbursky@virtuozzo.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Pavel Emelyanov <xemul@virtuozzo.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When commit fbae2d44aa ("kthread: add kthread_create_worker*()")
introduced some kthread_create_...() functions which were taking
printf-like parametter, it introduced __printf attributes to some
functions (e.g. kthread_create_worker()). Nevertheless some new
functions were forgotten (they have been detected thanks to
-Wmissing-format-attribute warning flag).
Add the missing __printf attributes to the newly-introduced functions in
order to detect formatting issues at build-time with -Wformat flag.
Link: http://lkml.kernel.org/r/20161126193543.22672-1-nicolas.iooss_linux@m4x.org
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 265a5b7ee3 ("kprobes/trace: Fix kprobe selftest for gcc 4.6")
has added __used attribute to kprobe_trace_selftest_target to ensure
that the method is listed in kallsyms table.
However, even though the method remains in the kernel image, the actual
call is optimized away as there are no side effects and the return value
is never checked.
Add a return value check and a 'noinline' attribute to ensure that an
inlined copy of the method is not used by the caller. Also add checks
that verify that the kprobe was really hit, as at the moment the tests
show positive results despite the test method being optimized away.
Finally, add __init annotations to find_trace_probe_file() and
kprobe_trace_selftest_target() as they are only called from within an
__init method.
Link: http://lkml.kernel.org/r/1481293178-3128-2-git-send-email-marcin.nowakowski@imgtec.com
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The number of probe hits is stored in a percpu variable and therefore
can't be read directly. Add a helper method trace_kprobe_nhit() that
performs the required calculation.
It will be used in a follow-up commit that changes kprobe selftests to
verify the number of probe hits.
Link: http://lkml.kernel.org/r/1481293178-3128-1-git-send-email-marcin.nowakowski@imgtec.com
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Before commit b32614c034 ("tracing/rb: Convert to hotplug state
machine") the allocated cpumask was initialized to the mask of ONLINE or
POSSIBLE CPUs. After the CPU hotplug changes the buffer initialisation
moved to trace_rb_cpu_prepare() but I forgot to initially set the
cpumask to zero. This is done now.
Link: http://lkml.kernel.org/r/20161207133133.hzkcqfllxcdi3joz@linutronix.de
Fixes: b32614c034 ("tracing/rb: Convert to hotplug state machine")
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Pull x86 asm updates from Ingo Molnar:
"The main changes in this development cycle were:
- a large number of call stack dumping/printing improvements: higher
robustness, better cross-context dumping, improved output, etc.
(Josh Poimboeuf)
- vDSO getcpu() performance improvement for future Intel CPUs with
the RDPID instruction (Andy Lutomirski)
- add two new Intel AVX512 features and the CPUID support
infrastructure for it: AVX512IFMA and AVX512VBMI. (Gayatri Kammela,
He Chen)
- more copy-user unification (Borislav Petkov)
- entry code assembly macro simplifications (Alexander Kuleshov)
- vDSO C/R support improvements (Dmitry Safonov)
- misc fixes and cleanups (Borislav Petkov, Paul Bolle)"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
scripts/decode_stacktrace.sh: Fix address line detection on x86
x86/boot/64: Use defines for page size
x86/dumpstack: Make stack name tags more comprehensible
selftests/x86: Add test_vdso to test getcpu()
x86/vdso: Use RDPID in preference to LSL when available
x86/dumpstack: Handle NULL stack pointer in show_trace_log_lvl()
x86/cpufeatures: Enable new AVX512 cpu features
x86/cpuid: Provide get_scattered_cpuid_leaf()
x86/cpuid: Cleanup cpuid_regs definitions
x86/copy_user: Unify the code by removing the 64-bit asm _copy_*_user() variants
x86/unwind: Ensure stack grows down
x86/vdso: Set vDSO pointer only after success
x86/prctl/uapi: Remove #ifdef for CHECKPOINT_RESTORE
x86/unwind: Detect bad stack return address
x86/dumpstack: Warn on stack recursion
x86/unwind: Warn on bad frame pointer
x86/decoder: Use stderr if insn sanity test fails
x86/decoder: Use stdout if insn decoder test is successful
mm/page_alloc: Remove kernel address exposure in free_reserved_area()
x86/dumpstack: Remove raw stack dump
...
Pull hotplug API fix from Ingo Molnar:
"Late breaking fix from the v4.9 cycle: fix a hotplug register/
unregister notifier API asymmetry bug that can cause kernel warnings
(and worse) with certain Kconfig combinations"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hotplug: Make register and unregister notifier API symmetric
Pull scheduler updates from Ingo Molnar:
"The main scheduler changes in this cycle were:
- support Intel Turbo Boost Max Technology 3.0 (TBM3) by introducig a
notion of 'better cores', which the scheduler will prefer to
schedule single threaded workloads on. (Tim Chen, Srinivas
Pandruvada)
- enhance the handling of asymmetric capacity CPUs further (Morten
Rasmussen)
- improve/fix load handling when moving tasks between task groups
(Vincent Guittot)
- simplify and clean up the cputime code (Stanislaw Gruszka)
- improve mass fork()ed task spread a.k.a. hackbench speedup (Vincent
Guittot)
- make struct kthread kmalloc()ed and related fixes (Oleg Nesterov)
- add uaccess atomicity debugging (when using access_ok() in the
wrong context), under CONFIG_DEBUG_ATOMIC_SLEEP=y (Peter Zijlstra)
- implement various fixes, cleanups and other enhancements (Daniel
Bristot de Oliveira, Martin Schwidefsky, Rafael J. Wysocki)"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
sched/core: Use load_avg for selecting idlest group
sched/core: Fix find_idlest_group() for fork
kthread: Don't abuse kthread_create_on_cpu() in __kthread_create_worker()
kthread: Don't use to_live_kthread() in kthread_[un]park()
kthread: Don't use to_live_kthread() in kthread_stop()
Revert "kthread: Pin the stack via try_get_task_stack()/put_task_stack() in to_live_kthread() function"
kthread: Make struct kthread kmalloc'ed
x86/uaccess, sched/preempt: Verify access_ok() context
sched/x86: Make CONFIG_SCHED_MC_PRIO=y easier to enable
sched/x86: Change CONFIG_SCHED_ITMT to CONFIG_SCHED_MC_PRIO
x86/sched: Use #include <linux/mutex.h> instead of #include <asm/mutex.h>
cpufreq/intel_pstate: Use CPPC to get max performance
acpi/bus: Set _OSC for diverse core support
acpi/bus: Enable HWP CPPC objects
x86/sched: Add SD_ASYM_PACKING flags to x86 ITMT CPU
x86/sysctl: Add sysctl for ITMT scheduling feature
x86: Enable Intel Turbo Boost Max Technology 3.0
x86/topology: Define x86's arch_update_cpu_topology
sched: Extend scheduler's asym packing
sched/fair: Clean up the tunable parameter definitions
...
* pm-cpuidle:
cpuidle: Add a kerneldoc comment to cpuidle_use_deepest_state()
cpuidle: fix improper return value on error
intel_idle: Convert to hotplug state machine
intel_idle: Remove superfluous SMP fuction call
MAINTAINERS: Add Jacob Pan as a new intel_idle maintainer
MAINTAINERS: Add bug tracking system location entries for cpuidle
x86/intel_idle: Add Knights Mill CPUID
x86/intel_idle: Add CPU model 0x4a (Atom Z34xx series)
thermal/intel_powerclamp: stop sched tick in forced idle
thermal/intel_powerclamp: Convert to CPU hotplug state
thermal/intel_powerclamp: Convert the kthread to kthread worker API
thermal/intel_powerclamp: Remove duplicated code that starts the kthread
sched/idle: Add support for tasks that inject idle
cpuidle: Allow enforcing deepest idle state selection
cpuidle/powernv: staticise powernv_idle_driver
cpuidle: dt: assign ->enter_freeze to same as ->enter callback function
cpuidle: governors: Remove remaining old module code
* pm-cpufreq: (51 commits)
Documentation: intel_pstate: Document HWP energy/performance hints
cpufreq: intel_pstate: Support for energy performance hints with HWP
cpufreq: intel_pstate: Add locking around HWP requests
cpufreq: ondemand: Set MIN_FREQUENCY_UP_THRESHOLD to 1
cpufreq: intel_pstate: Add Knights Mill CPUID
MAINTAINERS: Add bug tracking system location entry for cpufreq
cpufreq: dt: Add support for zx296718
cpufreq: acpi-cpufreq: drop rdmsr_on_cpus() usage
cpufreq: acpi-cpufreq: Convert to hotplug state machine
cpufreq: intel_pstate: fix intel_pstate_exit_perf_limits() prototype
cpufreq: intel_pstate: Set EPP/EPB to 0 in performance mode
cpufreq: schedutil: Rectify comment in sugov_irq_work() function
cpufreq: intel_pstate: increase precision of performance limits
cpufreq: intel_pstate: round up min_perf limits
cpufreq: Make cpufreq_update_policy() void
ACPI / processor: Make acpi_processor_ppc_has_changed() void
cpufreq: Avoid using inactive policies
cpufreq: intel_pstate: Generic governors support
cpufreq: intel_pstate: Request P-states control from SMM if needed
cpufreq: dt: Add support for r8a7743 and r8a7745
...
The 's' flag is supposed to indicate that a softirq is running. This
can be detected by testing the preempt_count with SOFTIRQ_OFFSET.
The current code tests the preempt_count with SOFTIRQ_MASK, which
would be true even when softirqs are disabled but not serving a
softirq.
Link: http://lkml.kernel.org/r/1481300417-3564-1-git-send-email-pkondeti@codeaurora.org
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Pull locking updates from Ingo Molnar:
"The tree got pretty big in this development cycle, but the net effect
is pretty good:
115 files changed, 673 insertions(+), 1522 deletions(-)
The main changes were:
- Rework and generalize the mutex code to remove per arch mutex
primitives. (Peter Zijlstra)
- Add vCPU preemption support: add an interface to query the
preemption status of vCPUs and use it in locking primitives - this
optimizes paravirt performance. (Pan Xinhui, Juergen Gross,
Christian Borntraeger)
- Introduce cpu_relax_yield() and remov cpu_relax_lowlatency() to
clean up and improve the s390 lock yielding machinery and its core
kernel impact. (Christian Borntraeger)
- Micro-optimize mutexes some more. (Waiman Long)
- Reluctantly add the to-be-deprecated mutex_trylock_recursive()
interface on a temporary basis, to give the DRM code more time to
get rid of its locking hacks. Any other users will be NAK-ed on
sight. (We turned off the deprecation warning for the time being to
not pollute the build log.) (Peter Zijlstra)
- Improve the rtmutex code a bit, in light of recent long lived
bugs/races. (Thomas Gleixner)
- Misc fixes, cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
x86/paravirt: Fix bool return type for PVOP_CALL()
x86/paravirt: Fix native_patch()
locking/ww_mutex: Use relaxed atomics
locking/rtmutex: Explain locking rules for rt_mutex_proxy_unlock()/init_proxy_locked()
locking/rtmutex: Get rid of RT_MUTEX_OWNER_MASKALL
x86/paravirt: Optimize native pv_lock_ops.vcpu_is_preempted()
locking/mutex: Break out of expensive busy-loop on {mutex,rwsem}_spin_on_owner() when owner vCPU is preempted
locking/osq: Break out of spin-wait busy waiting loop for a preempted vCPU in osq_lock()
Documentation/virtual/kvm: Support the vCPU preemption check
x86/xen: Support the vCPU preemption check
x86/kvm: Support the vCPU preemption check
x86/kvm: Support the vCPU preemption check
kvm: Introduce kvm_write_guest_offset_cached()
locking/core, x86/paravirt: Implement vcpu_is_preempted(cpu) for KVM and Xen guests
locking/spinlocks, s390: Implement vcpu_is_preempted(cpu)
locking/core, powerpc: Implement vcpu_is_preempted(cpu)
sched/core: Introduce the vcpu_is_preempted(cpu) interface
sched/wake_q: Rename WAKE_Q to DEFINE_WAKE_Q
locking/core: Provide common cpu_relax_yield() definition
locking/mutex: Don't mark mutex_trylock_recursive() as deprecated, temporarily
...
Pull SMP bootup updates from Ingo Molnar:
"Three changes to unify/standardize some of the bootup message printing
in kernel/smp.c between architectures"
* 'core-smp-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kernel/smp: Tell the user we're bringing up secondary CPUs
kernel/smp: Make the SMP boot message common on all arches
kernel/smp: Define pr_fmt() for smp.c
Pull RCU updates from Ingo Molnar:
"The main RCU changes in this development cycle were:
- Miscellaneous fixes, including a change to call_rcu()'s rcu_head
alignment check.
- Security-motivated list consistency checks, which are disabled by
default behind DEBUG_LIST.
- Torture-test updates.
- Documentation updates, yet again just simple changes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
torture: Prevent jitter from delaying build-only runs
torture: Remove obsolete files from rcutorture .gitignore
rcu: Don't kick unless grace period or request
rcu: Make expedited grace periods recheck dyntick idle state
torture: Trace long read-side delays
rcu: RCU_TRACE enables event tracing as well as debugfs
rcu: Remove obsolete comment from __call_rcu()
rcu: Remove obsolete rcu_check_callbacks() header comment
rcu: Tighten up __call_rcu() rcu_head alignment check
Documentation/RCU: Fix minor typo
documentation: Present updated RCU guarantee
bug: Avoid Kconfig warning for BUG_ON_DATA_CORRUPTION
lib/Kconfig.debug: Fix typo in select statement
lkdtm: Add tests for struct list corruption
bug: Provide toggle for BUG on data corruption
list: Split list_del() debug checking into separate function
rculist: Consolidate DEBUG_LIST for list_add_rcu()
list: Split list_add() debug checking into separate function
find_idlest_group() only compares the runnable_load_avg when looking
for the least loaded group. But on fork intensive use case like
hackbench where tasks blocked quickly after the fork, this can lead to
selecting the same CPU instead of other CPUs, which have similar
runnable load but a lower load_avg.
When the runnable_load_avg of 2 CPUs are close, we now take into
account the amount of blocked load as a 2nd selection factor. There is
now 3 zones for the runnable_load of the rq:
- [0 .. (runnable_load - imbalance)]:
Select the new rq which has significantly less runnable_load
- [(runnable_load - imbalance) .. (runnable_load + imbalance)]:
The runnable loads are close so we use load_avg to chose
between the 2 rq
- [(runnable_load + imbalance) .. ULONG_MAX]:
Keep the current rq which has significantly less runnable_load
The scale factor that is currently used for comparing runnable_load,
doesn't work well with small value. As an example, the use of a
scaling factor fails as soon as this_runnable_load == 0 because we
always select local rq even if min_runnable_load is only 1, which
doesn't really make sense because they are just the same. So instead
of scaling factor, we use an absolute margin for runnable_load to
detect CPUs with similar runnable_load and we keep using scaling
factor for blocked load.
For use case like hackbench, this enable the scheduler to select
different CPUs during the fork sequence and to spread tasks across the
system.
Tests have been done on a Hikey board (ARM based octo cores) for
several kernel. The result below gives min, max, avg and stdev values
of 18 runs with each configuration.
The patches depend on the "no missing update_rq_clock()" work.
hackbench -P -g 1
ea86cb4b767dc603c902 v4.8 v4.8+patches
min 0.049 0.050 0.051 0,048
avg 0.057 0.057(0%) 0.057(0%) 0,055(+5%)
max 0.066 0.068 0.070 0,063
stdev +/-9% +/-9% +/-8% +/-9%
More performance numbers here:
https://lkml.kernel.org/r/20161203214707.GI20785@codeblueprint.co.uk
Tested-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten.Rasmussen@arm.com
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dietmar.eggemann@arm.com
Cc: kernellwp@gmail.com
Cc: umgwanakikbuti@gmail.com
Cc: yuyang.du@intel.comc
Link: http://lkml.kernel.org/r/1481216215-24651-3-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
During fork, the utilization of a task is init once the rq has been
selected because the current utilization level of the rq is used to
set the utilization of the fork task. As the task's utilization is
still 0 at this step of the fork sequence, it doesn't make sense to
look for some spare capacity that can fit the task's utilization.
Furthermore, I can see perf regressions for the test:
hackbench -P -g 1
because the least loaded policy is always bypassed and tasks are not
spread during fork.
With this patch and the fix below, we are back to same performances as
for v4.8. The fix below is only a temporary one used for the test
until a smarter solution is found because we can't simply remove the
test which is useful for others benchmarks
| @@ -5708,13 +5708,6 @@ static int select_idle_cpu(struct task_struct *p, struct sched_domain *sd, int t
|
| avg_cost = this_sd->avg_scan_cost;
|
| - /*
| - * Due to large variance we need a large fuzz factor; hackbench in
| - * particularly is sensitive here.
| - */
| - if ((avg_idle / 512) < avg_cost)
| - return -1;
| -
| time = local_clock();
|
| for_each_cpu_wrap(cpu, sched_domain_span(sd), target, wrap) {
Tested-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dietmar.eggemann@arm.com
Cc: kernellwp@gmail.com
Cc: umgwanakikbuti@gmail.com
Cc: yuyang.du@intel.comc
Link: http://lkml.kernel.org/r/1481216215-24651-2-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently both the wakeup and irqsoff traces do not handle set_graph_notrace
well. The ftrace infrastructure will ignore the return paths of all
functions leaving them hanging without an end:
# echo '*spin*' > set_graph_notrace
# cat trace
[...]
_raw_spin_lock() {
preempt_count_add() {
do_raw_spin_lock() {
update_rq_clock();
Where the '*spin*' functions should have looked like this:
_raw_spin_lock() {
preempt_count_add();
do_raw_spin_lock();
}
update_rq_clock();
Instead, have the wakeup and irqsoff tracers ignore the functions that are
set by the set_graph_notrace like the function_graph tracer does. Move
the logic in the function_graph tracer into a header to allow wakeup and
irqsoff tracers to use it as well.
Cc: Namhyung Kim <namhyung.kim@lge.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Both the wakeup and irqsoff tracers can use the function graph tracer when
the display-graph option is set. The problem is that they ignore the notrace
file, and record the entry of functions that would be ignored by the
function_graph tracer. This causes the trace->depth to be recorded into the
ring buffer. The set_graph_notrace uses a trick by adding a large negative
number to the trace->depth when a graph function is to be ignored.
On trace output, the graph function uses the depth to record a stack of
functions. But since the depth is negative, it accesses the array with a
negative number and causes an out of bounds access that can cause a kernel
oops or corrupt data.
Have the print functions handle cases where a tracer still records functions
even when they are in set_graph_notrace.
Also add warnings if the depth is below zero before accessing the array.
Note, the function graph logic will still prevent the return of these
functions from being recorded, which means that they will be left hanging
without a return. For example:
# echo '*spin*' > set_graph_notrace
# echo 1 > options/display-graph
# echo wakeup > current_tracer
# cat trace
[...]
_raw_spin_lock() {
preempt_count_add() {
do_raw_spin_lock() {
update_rq_clock();
Where it should look like:
_raw_spin_lock() {
preempt_count_add();
do_raw_spin_lock();
}
update_rq_clock();
Cc: stable@vger.kernel.org
Cc: Namhyung Kim <namhyung.kim@lge.com>
Fixes: 29ad23b004 ("ftrace: Add set_graph_notrace filter")
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Instead of using get_user_pages_fast() and kmap_atomic() when writing
to the trace_marker file, just allocate enough space on the ring buffer
directly, and write into it via copy_from_user().
Writing into the trace_marker file use to allocate a temporary buffer
to perform the copy_from_user(), as we didn't want to write into the
ring buffer if the copy failed. But as a trace_marker write is suppose
to be extremely fast, and allocating memory causes other tracepoints to
trigger, Peter Zijlstra suggested using get_user_pages_fast() and
kmap_atomic() to keep the user space pages in memory and reading it
directly. But Henrik Austad had issues with this because it required taking
the mm->mmap_sem and causing long delays with the write.
Instead, just allocate the space in the ring buffer and use
copy_from_user() directly. If it faults, return -EFAULT and write
"<faulted>" into the ring buffer.
Link: http://lkml.kernel.org/r/20161208124018.72dd0f86@gandalf.local.home
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Henrik Austad <henrik@austad.us>
Cc: Peter Zijlstra <peterz@infradead.org>
Updates: d696b58ca2 "tracing: Do not allocate buffer for trace_marker"
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The trace event start up selftests fails when the trace benchmark is
enabled, because it is disabled during boot. It really only needs to be
disabled before scheduling is set up, as it creates a thread.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If one of the events within a system fails to enable when "1" is written
to the system "enable" file, it should return an error. Note, some events
may still be enabled, but the user should know that something did go wrong.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Trace events are enabled very early on boot up via the boot command line
parameter. The benchmark tool creates a new thread to perform the trace
event benchmarking. But at start up, it is called before scheduling is set
up and because it creates a new thread before the init thread is created,
this crashes the kernel.
Have the benchmark fail to register when started via the kernel command
line.
Also, since the registering of a tracepoint now can handle failure cases,
return -ENOMEM instead of warning if the thread cannot be created.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Some tracepoints have a registration function that gets enabled when the
tracepoint is enabled. There may be cases that the registraction function
must fail (for example, can't allocate enough memory). In this case, the
tracepoint should also fail to register, otherwise the user would not know
why the tracepoint is not working.
Cc: David Howells <dhowells@redhat.com>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The resume code must deal with a clocksource delta which is potentially big
enough to overflow the 64bit mult.
Replace the open coded handling with the proper function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Parit Bhargava <prarit@redhat.com>
Cc: Laurent Vivier <lvivier@redhat.com>
Cc: "Christopher S. Hall" <christopher.s.hall@intel.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Liav Rehana <liavr@mellanox.com>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/20161208204228.921674404@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
cycle_t is defined as u64, so casting it to u64 is a pointless and
confusing exercise. cycle_t should simply go away and be replaced with a
plain u64 to avoid further confusion.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Parit Bhargava <prarit@redhat.com>
Cc: Laurent Vivier <lvivier@redhat.com>
Cc: "Christopher S. Hall" <christopher.s.hall@intel.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Liav Rehana <liavr@mellanox.com>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/20161208204228.844699737@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Propagating a unsigned value through signed variables and functions makes
absolutely no sense and is just prone to (re)introduce subtle signed
vs. unsigned issues as happened recently.
Clean it up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Parit Bhargava <prarit@redhat.com>
Cc: Laurent Vivier <lvivier@redhat.com>
Cc: "Christopher S. Hall" <christopher.s.hall@intel.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Liav Rehana <liavr@mellanox.com>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/20161208204228.765843099@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The clocksource delta to nanoseconds conversion is using signed math, but
the delta is unsigned. This makes the conversion space smaller than
necessary and in case of a multiplication overflow the conversion can
become negative. The conversion is done with scaled math:
s64 nsec_delta = ((s64)clkdelta * clk->mult) >> clk->shift;
Shifting a signed integer right obvioulsy preserves the sign, which has
interesting consequences:
- Time jumps backwards
- __iter_div_u64_rem() which is used in one of the calling code pathes
will take forever to piecewise calculate the seconds/nanoseconds part.
This has been reported by several people with different scenarios:
David observed that when stopping a VM with a debugger:
"It was essentially the stopped by debugger case. I forget exactly why,
but the guest was being explicitly stopped from outside, it wasn't just
scheduling lag. I think it was something in the vicinity of 10 minutes
stopped."
When lifting the stop the machine went dead.
The stopped by debugger case is not really interesting, but nevertheless it
would be a good thing not to die completely.
But this was also observed on a live system by Liav:
"When the OS is too overloaded, delta will get a high enough value for the
msb of the sum delta * tkr->mult + tkr->xtime_nsec to be set, and so
after the shift the nsec variable will gain a value similar to
0xffffffffff000000."
Unfortunately this has been reintroduced recently with commit 6bd58f09e1
("time: Add cycles to nanoseconds translation"). It had been fixed a year
ago already in commit 35a4933a89 ("time: Avoid signed overflow in
timekeeping_get_ns()").
Though it's not surprising that the issue has been reintroduced because the
function itself and the whole call chain uses s64 for the result and the
propagation of it. The change in this recent commit is subtle:
s64 nsec;
- nsec = (d * m + n) >> s:
+ nsec = d * m + n;
+ nsec >>= s;
d being type of cycle_t adds another level of obfuscation.
This wouldn't have happened if the previous change to unsigned computation
would have made the 'nsec' variable u64 right away and a follow up patch
had cleaned up the whole call chain.
There have been patches submitted which basically did a revert of the above
patch leaving everything else unchanged as signed. Back to square one. This
spawned a admittedly pointless discussion about potential users which rely
on the unsigned behaviour until someone pointed out that it had been fixed
before. The changelogs of said patches added further confusion as they made
finally false claims about the consequences for eventual users which expect
signed results.
Despite delta being cycle_t, aka. u64, it's very well possible to hand in
a signed negative value and the signed computation will happily return the
correct result. But nobody actually sat down and analyzed the code which
was added as user after the propably unintended signed conversion.
Though in sensitive code like this it's better to analyze it proper and
make sure that nothing relies on this than hunting the subtle wreckage half
a year later. After analyzing all call chains it stands that no caller can
hand in a negative value (which actually would work due to the s64 cast)
and rely on the signed math to do the right thing.
Change the conversion function to unsigned math. The conversion of all call
chains is done in a follow up patch.
This solves the starvation issue, which was caused by the negative result,
but it does not solve the underlying problem. It merily procrastinates
it. When the timekeeper update is deferred long enough that the unsigned
multiplication overflows, then time going backwards is observable again.
It does neither solve the issue of clocksources with a small counter width
which will wrap around possibly several times and cause random time stamps
to be generated. But those are usually not found on systems used for
virtualization, so this is likely a non issue.
I took the liberty to claim authorship for this simply because
analyzing all callsites and writing the changelog took substantially
more time than just making the simple s/s64/u64/ change and ignore the
rest.
Fixes: 6bd58f09e1 ("time: Add cycles to nanoseconds translation")
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Reported-by: Liav Rehana <liavr@mellanox.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Parit Bhargava <prarit@redhat.com>
Cc: Laurent Vivier <lvivier@redhat.com>
Cc: "Christopher S. Hall" <christopher.s.hall@intel.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20161208204228.688545601@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch allows XDP prog to extend/remove the packet
data at the head (like adding or removing header). It is
done by adding a new XDP helper bpf_xdp_adjust_head().
It also renames bpf_helper_changes_skb_data() to
bpf_helper_changes_pkt_data() to better reflect
that XDP prog does not work on skb.
This patch adds one "xdp_adjust_head" bit to bpf_prog for the
XDP-capable driver to check if the XDP prog requires
bpf_xdp_adjust_head() support. The driver can then decide
to error out during XDP_SETUP_PROG.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commmits 57a09bf0a4 ("bpf: Detect identical PTR_TO_MAP_VALUE_OR_NULL registers")
and 484611357c ("bpf: allow access into map value arrays") by themselves
are correct, but in combination they make state equivalence ignore 'id' field
of the register state which can lead to accepting invalid program.
Fixes: 57a09bf0a4 ("bpf: Detect identical PTR_TO_MAP_VALUE_OR_NULL registers")
Fixes: 484611357c ("bpf: allow access into map value arrays")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
kthread_create_on_cpu() sets KTHREAD_IS_PER_CPU and kthread->cpu, this
only makes sense if this kthread can be parked/unparked by cpuhp code.
kthread workers never call kthread_parkme() so this has no effect.
Change __kthread_create_worker() to simply call kthread_bind(task, cpu).
The very fact that kthread_create_on_cpu() doesn't accept a generic fmt
shows that it should not be used outside of smpboot.c.
Now, the only reason we can not unexport this helper and move it into
smpboot.c is that it sets kthread->cpu and struct kthread is not exported.
And the only reason we can not kill kthread->cpu is that kthread_unpark()
is used by drivers/gpu/drm/amd/scheduler/gpu_scheduler.c and thus we can
not turn _unpark into kthread_unpark(struct smp_hotplug_thread *, cpu).
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Tested-by: Petr Mladek <pmladek@suse.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Cc: Chunming Zhou <David1.Zhou@amd.com>
Cc: Roman Pen <roman.penyaev@profitbricks.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20161129175110.GA5342@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now that to_kthread() is always validm change kthread_park() and
kthread_unpark() to use it and kill to_live_kthread().
The conversion of kthread_unpark() is trivial. If KTHREAD_IS_PARKED is set
then the task has called complete(&self->parked) and there the function
cannot race against a concurrent kthread_stop() and exit.
kthread_park() is more tricky, because its semantics are not well
defined. It returns -ENOSYS if the thread exited but this can never happen
and as Roman pointed out kthread_park() can obviously block forever if it
would race with the exiting kthread.
The usage of kthread_park() in cpuhp code (cpu.c, smpboot.c, stop_machine.c)
is fine. It can never see an exiting/exited kthread, smpboot_destroy_threads()
clears *ht->store, smpboot_park_thread() checks it is not NULL under the same
smpboot_threads_lock. cpuhp_threads and cpu_stop_threads never exit, so other
callers are fine too.
But it has two more users:
- watchdog_park_threads():
The code is actually correct, get_online_cpus() ensures that
kthread_park() can't race with itself (note that kthread_park() can't
handle this race correctly), but it should not use kthread_park()
directly.
- drivers/gpu/drm/amd/scheduler/gpu_scheduler.c should not use
kthread_park() either.
kthread_park() must not be called after amd_sched_fini() which does
kthread_stop(), otherwise even to_live_kthread() is not safe because
task_struct can be already freed and sched->thread can point to nowhere.
The usage of kthread_park/unpark should either be restricted to core code
which is properly protected against the exit race or made more robust so it
is safe to use it in drivers.
To catch eventual exit issues, add a WARN_ON(PF_EXITING) for now.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Chunming Zhou <David1.Zhou@amd.com>
Cc: Roman Pen <roman.penyaev@profitbricks.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20161129175107.GA5339@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
kthread_stop() had to use to_live_kthread() simply because it was not
possible to access kthread->exited after the exiting task clears
task_struct->vfork_done. Now that to_kthread() is always valid,
wake_up_process() + wait_for_completion() can be done
ununconditionally. It's not an issue anymore if the task has already issued
complete_vfork_done() or died.
The exiting task can get the spurious wakeup after mm_release() but this is
possible without this change too and is fine; do_task_dead() ensures that
this can't make any harm.
As a further enhancement this could be converted to task_work_add() later,
so ->vfork_done can be avoided completely.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Chunming Zhou <David1.Zhou@amd.com>
Cc: Roman Pen <roman.penyaev@profitbricks.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20161129175103.GA5336@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This reverts commit 23196f2e5f.
Now that struct kthread is kmalloc'ed and not longer on the task stack
there is no need anymore to pin the stack.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Chunming Zhou <David1.Zhou@amd.com>
Cc: Roman Pen <roman.penyaev@profitbricks.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20161129175100.GA5333@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
commit 23196f2e5f "kthread: Pin the stack via try_get_task_stack() /
put_task_stack() in to_live_kthread() function" is a workaround for the
fragile design of struct kthread being allocated on the task stack.
struct kthread in its current form should be removed, but this needs
cleanups outside of kthread.c.
As a first step move struct kthread away from the task stack by making it
kmalloc'ed. This allows to access kthread.exited without the magic of
trying to pin task stack and the try logic in to_live_kthread().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Chunming Zhou <David1.Zhou@amd.com>
Cc: Roman Pen <roman.penyaev@profitbricks.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20161129175057.GA5330@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Yu Zhao has noticed that __unregister_cpu_notifier only unregisters its
notifiers when HOTPLUG_CPU=y while the registration might succeed even
when HOTPLUG_CPU=n if MODULE is enabled. This means that e.g. zswap
might keep a stale notifier on the list on the manual clean up during
the pool tear down and thus corrupt the list. Resulting in the following
[ 144.964346] BUG: unable to handle kernel paging request at ffff880658a2be78
[ 144.971337] IP: [<ffffffffa290b00b>] raw_notifier_chain_register+0x1b/0x40
<snipped>
[ 145.122628] Call Trace:
[ 145.125086] [<ffffffffa28e5cf8>] __register_cpu_notifier+0x18/0x20
[ 145.131350] [<ffffffffa2a5dd73>] zswap_pool_create+0x273/0x400
[ 145.137268] [<ffffffffa2a5e0fc>] __zswap_param_set+0x1fc/0x300
[ 145.143188] [<ffffffffa2944c1d>] ? trace_hardirqs_on+0xd/0x10
[ 145.149018] [<ffffffffa2908798>] ? kernel_param_lock+0x28/0x30
[ 145.154940] [<ffffffffa2a3e8cf>] ? __might_fault+0x4f/0xa0
[ 145.160511] [<ffffffffa2a5e237>] zswap_compressor_param_set+0x17/0x20
[ 145.167035] [<ffffffffa2908d3c>] param_attr_store+0x5c/0xb0
[ 145.172694] [<ffffffffa290848d>] module_attr_store+0x1d/0x30
[ 145.178443] [<ffffffffa2b2b41f>] sysfs_kf_write+0x4f/0x70
[ 145.183925] [<ffffffffa2b2a5b9>] kernfs_fop_write+0x149/0x180
[ 145.189761] [<ffffffffa2a99248>] __vfs_write+0x18/0x40
[ 145.194982] [<ffffffffa2a9a412>] vfs_write+0xb2/0x1a0
[ 145.200122] [<ffffffffa2a9a732>] SyS_write+0x52/0xa0
[ 145.205177] [<ffffffffa2ff4d97>] entry_SYSCALL_64_fastpath+0x12/0x17
This can be even triggered manually by changing
/sys/module/zswap/parameters/compressor multiple times.
Fix this issue by making unregister APIs symmetric to the register so
there are no surprises.
Fixes: 47e627bc8c ("[PATCH] hotplug: Allow modules to use the cpu hotplug notifiers even if !CONFIG_HOTPLUG_CPU")
Reported-and-tested-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Cc: linux-mm@kvack.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dan Streetman <ddstreet@ieee.org>
Link: http://lkml.kernel.org/r/20161207135438.4310-1-mhocko@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In __sanitizer_cov_trace_pc we use task_struct and fields within it, but
as we haven't included <linux/sched.h>, it is not guaranteed to be
defined. While we usually happen to acquire the definition through a
transitive include, this is fragile (and hasn't been true in the past,
causing issues with backports).
Include <linux/sched.h> to avoid any fragility.
[mark.rutland@arm.com: rewrote changelog]
Link: http://lkml.kernel.org/r/1481007384-27529-1-git-send-email-wangkefeng.wang@huawei.com
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull perf fixes from Ingo Molnar:
"A bogus warning fix, a counter width handling fix affecting certain
machines, plus a oneliner hw-enablement patch for Knights Mill CPUs"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Remove invalid warning from list_update_cgroup_even()t
perf/x86: Fix full width counter, counter overflow
perf/x86/intel: Enable C-state residency events for Knights Mill
Pull locking fixes from Ingo Molnar:
"Two rtmutex race fixes (which miraculously never triggered, that we
know of), plus two lockdep printk formatting regression fixes"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lockdep: Fix report formatting
locking/rtmutex: Use READ_ONCE() in rt_mutex_owner()
locking/rtmutex: Prevent dequeue vs. unlock race
locking/selftest: Fix output since KERN_CONT changes
General assumption is that single program can hold up to BPF_MAXINSNS,
that is, 4096 number of instructions. It is the case with cBPF and
that limit was carried over to eBPF. When recently testing digest, I
noticed that it's actually not possible to feed 4096 instructions
via bpf(2).
The check for > BPF_MAXINSNS was added back then to bpf_check() in
cbd3570086 ("bpf: verifier (add ability to receive verification log)").
However, 09756af468 ("bpf: expand BPF syscall with program load/unload")
added yet another check that comes before that into bpf_prog_load(),
but this time bails out already in case of >= BPF_MAXINSNS.
Fix it up and perform the check early in bpf_prog_load(), so we can drop
the second one in bpf_check(). It makes sense, because also a 0 insn
program is useless and we don't want to waste any resources doing work
up to bpf_check() point. The existing bpf(2) man page documents E2BIG
as the official error for such cases, so just stick with it as well.
Fixes: 09756af468 ("bpf: expand BPF syscall with program load/unload")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW CPTS driver is capable of doing timestamping on tx/rx packets and
requires to know mult and shift factors for timestamp conversion from raw
value to nanoseconds (ptp clock). Now these mult and shift factors are
calculated manually and provided through DT, which makes very hard to
support of a lot number of platforms, especially if CPTS refclk is not the
same for some kind of boards and depends on efuse settings (Keystone 2
platforms). Hence, export clocks_calc_mult_shift() to allow drivers like
CPSW CPTS (and other ptp drivesr) to benefit from automaitc calculation of
mult and shift factors.
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit b32614c034 ("tracing/rb: Convert to hotplug state machine")
the allocated cpumask was initialized to the mask of online or possible
CPUs. After the CPU hotplug changes the buffer initialization moved to
trace_rb_cpu_prepare() but the cpumask is allocated with alloc_cpumask()
and therefor has random content. As a consequence the cpu buffers are not
initialized and a later access dereferences a NULL pointer.
Use zalloc_cpumask() instead so trace_rb_cpu_prepare() initializes the
buffers properly.
Fixes: b32614c034 ("tracing/rb: Convert to hotplug state machine")
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: rostedt@goodmis.org
Link: http://lkml.kernel.org/r/20161207133133.hzkcqfllxcdi3joz@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since commit:
4bcc595ccd ("printk: reinstate KERN_CONT for printing continuation lines")
printk() requires KERN_CONT to continue log messages. Lots of printk()
in lockdep.c and print_ip_sym() don't have it. As the result lockdep
reports are completely messed up.
Add missing KERN_CONT and inline print_ip_sym() where necessary.
Example of a messed up report:
0-rc5+ #41 Not tainted
-------------------------------------------------------
syz-executor0/5036 is trying to acquire lock:
(
rtnl_mutex
){+.+.+.}
, at:
[<ffffffff86b3d6ac>] rtnl_lock+0x1c/0x20
but task is already holding lock:
(
&net->packet.sklist_lock
){+.+...}
, at:
[<ffffffff873541a6>] packet_diag_dump+0x1a6/0x1920
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3
(
&net->packet.sklist_lock
+.+...}
...
Without this patch all scripts that parse kernel bug reports are broken.
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: andreyknvl@google.com
Cc: aryabinin@virtuozzo.com
Cc: joe@perches.com
Cc: syzkaller@googlegroups.com
Link: http://lkml.kernel.org/r/1480343083-48731-1-git-send-email-dvyukov@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The warning introduced in commit:
864c2357ca ("perf/core: Do not set cpuctx->cgrp for unscheduled cgroups")
assumed that a cgroup switch always precedes list_del_event. This is
not the case. Remove warning.
Make sure that cpuctx->cgrp is NULL until a cgroup event is sched in
or ctx->nr_cgroups == 0.
Signed-off-by: David Carrillo-Cisneros <davidcc@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi V Shankar <ravi.v.shankar@intel.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Vikas Shivappa <vikas.shivappa@linux.intel.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1480841177-27299-1-git-send-email-davidcc@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When loading a BPF program via bpf(2), calculate the digest over
the program's instruction stream and store it in struct bpf_prog's
digest member. This is done at a point in time before any instructions
are rewritten by the verifier. Any unstable map file descriptor
number part of the imm field will be zeroed for the hash.
fdinfo example output for progs:
# cat /proc/1590/fdinfo/5
pos: 0
flags: 02000002
mnt_id: 11
prog_type: 1
prog_jited: 1
prog_digest: b27e8b06da22707513aa97363dfb11c7c3675d28
memlock: 4096
When programs are pinned and retrieved by an ELF loader, the loader
can check the program's digest through fdinfo and compare it against
one that was generated over the ELF file's program section to see
if the program needs to be reloaded. Furthermore, this can also be
exposed through other means such as netlink in case of a tc cls/act
dump (or xdp in future), but also through tracepoints or other
facilities to identify the program. Other than that, the digest can
also serve as a base name for the work in progress kallsyms support
of programs. The digest doesn't depend/select the crypto layer, since
we need to keep dependencies to a minimum. iproute2 will get support
for this facility.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
copy_from_iter_full(), copy_from_iter_full_nocache() and
csum_and_copy_from_iter_full() - counterparts of copy_from_iter()
et.al., advancing iterator only in case of successful full copy
and returning whether it had been successful or not.
Convert some obvious users. *NOTE* - do not blindly assume that
something is a good candidate for those unless you are sure that
not advancing iov_iter in failure case is the right thing in
this case. Anything that does short read/short write kind of
stuff (or is in a loop, etc.) is unlikely to be a good one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Occasionally, clang (e.g. version 3.8.1) translates a sum between two
constant operands using a BPF_OR instead of a BPF_ADD. The verifier is
currently not handling this scenario, and the destination register type
becomes UNKNOWN_VALUE even if it's still storing a constant. As a result,
the destination register cannot be used as argument to a helper function
expecting a ARG_CONST_STACK_*, limiting some use cases.
Modify the verifier to handle this case, and add a few tests to make sure
all combinations are supported, and stack boundaries are still verified
even with BPF_OR.
Signed-off-by: Gianluca Borello <g.borello@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Lots more phydev and probe error path leaks in various drivers by
Johan Hovold.
2) Fix race in packet_set_ring(), from Philip Pettersson.
3) Use after free in dccp_invalid_packet(), from Eric Dumazet.
4) Signnedness overflow in SO_{SND,RCV}BUFFORCE, also from Eric
Dumazet.
5) When tunneling between ipv4 and ipv6 we can be left with the wrong
skb->protocol value as we enter the IPSEC engine and this causes all
kinds of problems. Set it before the output path does any
dst_output() calls, from Eli Cooper.
6) bcmgenet uses wrong device struct pointer in DMA API calls, fix from
Florian Fainelli.
7) Various netfilter nat bug fixes from FLorian Westphal.
8) Fix memory leak in ipvlan_link_new(), from Gao Feng.
9) Locking fixes, particularly wrt. socket lookups, in l2tp from
Guillaume Nault.
10) Avoid invoking rhash teardowns in atomic context by moving netlink
cb->done() dump completion from a worker thread. Fix from Herbert
Xu.
11) Buffer refcount problems in tun and macvtap on errors, from Jason
Wang.
12) We don't set Kconfig symbol DEFAULT_TCP_CONG properly when the user
selects BBR. Fix from Julian Wollrath.
13) Fix deadlock in transmit path on altera TSE driver, from Lino
Sanfilippo.
14) Fix unbalanced reference counting in dsa_switch_tree, from Nikita
Yushchenko.
15) tc_tunnel_key needs to be properly exported to userspace via uapi,
fix from Roi Dayan.
16) rds_tcp_init_net() doesn't unregister notifier in error path, fix
from Sowmini Varadhan.
17) Stale packet header pointer access after pskb_expand_head() in
genenve driver, fix from Sabrina Dubroca.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (103 commits)
net: avoid signed overflows for SO_{SND|RCV}BUFFORCE
geneve: avoid use-after-free of skb->data
tipc: check minimum bearer MTU
net: renesas: ravb: unintialized return value
sh_eth: remove unchecked interrupts for RZ/A1
net: bcmgenet: Utilize correct struct device for all DMA operations
NET: usb: qmi_wwan: add support for Telit LE922A PID 0x1040
cdc_ether: Fix handling connection notification
ip6_offload: check segs for NULL in ipv6_gso_segment.
RDS: TCP: unregister_netdevice_notifier() in error path of rds_tcp_init_net
Revert: "ip6_tunnel: Update skb->protocol to ETH_P_IPV6 in ip6_tnl_xmit()"
ipv6: Set skb->protocol properly for local output
ipv4: Set skb->protocol properly for local output
packet: fix race condition in packet_set_ring
net: ethernet: altera: TSE: do not use tx queue lock in tx completion handler
net: ethernet: altera: TSE: Remove unneeded dma sync for tx buffers
net: ethernet: stmmac: fix of-node and fixed-link-phydev leaks
net: ethernet: stmmac: platform: fix outdated function header
net: ethernet: stmmac: dwmac-meson8b: fix probe error path
net: ethernet: stmmac: dwmac-generic: fix probe error path
...
Add new cgroup based program type, BPF_PROG_TYPE_CGROUP_SOCK. Similar to
BPF_PROG_TYPE_CGROUP_SKB programs can be attached to a cgroup and run
any time a process in the cgroup opens an AF_INET or AF_INET6 socket.
Currently only sk_bound_dev_if is exported to userspace for modification
by a bpf program.
This allows a cgroup to be configured such that AF_INET{6} sockets opened
by processes are automatically bound to a specific device. In turn, this
enables the running of programs that do not support SO_BINDTODEVICE in a
specific VRF context / L3 domain.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code move and rename only; no functional change intended.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Registers new BPF program types which correspond to the LWT hooks:
- BPF_PROG_TYPE_LWT_IN => dst_input()
- BPF_PROG_TYPE_LWT_OUT => dst_output()
- BPF_PROG_TYPE_LWT_XMIT => lwtunnel_xmit()
The separate program types are required to differentiate between the
capabilities each LWT hook allows:
* Programs attached to dst_input() or dst_output() are restricted and
may only read the data of an skb. This prevent modification and
possible invalidation of already validated packet headers on receive
and the construction of illegal headers while the IP headers are
still being assembled.
* Programs attached to lwtunnel_xmit() are allowed to modify packet
content as well as prepending an L2 header via a newly introduced
helper bpf_skb_change_head(). This is safe as lwtunnel_xmit() is
invoked after the IP header has been assembled completely.
All BPF programs receive an skb with L3 headers attached and may return
one of the following error codes:
BPF_OK - Continue routing as per nexthop
BPF_DROP - Drop skb and return EPERM
BPF_REDIRECT - Redirect skb to device as per redirect() helper.
(Only valid in lwtunnel_xmit() context)
The return codes are binary compatible with their TC_ACT_
relatives to ease compatibility.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
While debugging the unlock vs. dequeue race which resulted in state
corruption of futexes the lockless nature of rt_mutex_proxy_unlock()
caused some confusion.
Add commentry to explain why it is safe to do this lockless. Add matching
comments to rt_mutex_init_proxy_locked() for completeness sake.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Will Deacon <will.deacon@arm.com>
Link: http://lkml.kernel.org/r/20161130210030.591941927@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is a left over from the original rtmutex implementation which used
both bit0 and bit1 in the owner pointer. Commit:
8161239a8b ("rtmutex: Simplify PI algorithm and make highest prio task get lock")
... removed the usage of bit1, but kept the extra mask around. This is
confusing at best.
Remove it and just use RT_MUTEX_HAS_WAITERS for the masking.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Will Deacon <will.deacon@arm.com>
Link: http://lkml.kernel.org/r/20161130210030.509567906@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While debugging the rtmutex unlock vs. dequeue race Will suggested to use
READ_ONCE() in rt_mutex_owner() as it might race against the
cmpxchg_release() in unlock_rt_mutex_safe().
Will: "It's a minor thing which will most likely not matter in practice"
Careful search did not unearth an actual problem in todays code, but it's
better to be safe than surprised.
Suggested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20161130210030.431379999@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
David reported a futex/rtmutex state corruption. It's caused by the
following problem:
CPU0 CPU1 CPU2
l->owner=T1
rt_mutex_lock(l)
lock(l->wait_lock)
l->owner = T1 | HAS_WAITERS;
enqueue(T2)
boost()
unlock(l->wait_lock)
schedule()
rt_mutex_lock(l)
lock(l->wait_lock)
l->owner = T1 | HAS_WAITERS;
enqueue(T3)
boost()
unlock(l->wait_lock)
schedule()
signal(->T2) signal(->T3)
lock(l->wait_lock)
dequeue(T2)
deboost()
unlock(l->wait_lock)
lock(l->wait_lock)
dequeue(T3)
===> wait list is now empty
deboost()
unlock(l->wait_lock)
lock(l->wait_lock)
fixup_rt_mutex_waiters()
if (wait_list_empty(l)) {
owner = l->owner & ~HAS_WAITERS;
l->owner = owner
==> l->owner = T1
}
lock(l->wait_lock)
rt_mutex_unlock(l) fixup_rt_mutex_waiters()
if (wait_list_empty(l)) {
owner = l->owner & ~HAS_WAITERS;
cmpxchg(l->owner, T1, NULL)
===> Success (l->owner = NULL)
l->owner = owner
==> l->owner = T1
}
That means the problem is caused by fixup_rt_mutex_waiters() which does the
RMW to clear the waiters bit unconditionally when there are no waiters in
the rtmutexes rbtree.
This can be fatal: A concurrent unlock can release the rtmutex in the
fastpath because the waiters bit is not set. If the cmpxchg() gets in the
middle of the RMW operation then the previous owner, which just unlocked
the rtmutex is set as the owner again when the write takes place after the
successfull cmpxchg().
The solution is rather trivial: verify that the owner member of the rtmutex
has the waiters bit set before clearing it. This does not require a
cmpxchg() or other atomic operations because the waiters bit can only be
set and cleared with the rtmutex wait_lock held. It's also safe against the
fast path unlock attempt. The unlock attempt via cmpxchg() will either see
the bit set and take the slowpath or see the bit cleared and release it
atomically in the fastpath.
It's remarkable that the test program provided by David triggers on ARM64
and MIPS64 really quick, but it refuses to reproduce on x86-64, while the
problem exists there as well. That refusal might explain that this got not
discovered earlier despite the bug existing from day one of the rtmutex
implementation more than 10 years ago.
Thanks to David for meticulously instrumenting the code and providing the
information which allowed to decode this subtle problem.
Reported-by: David Daney <ddaney@caviumnetworks.com>
Tested-by: David Daney <david.daney@cavium.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Fixes: 23f78d4a03 ("[PATCH] pi-futex: rt mutex core")
Link: http://lkml.kernel.org/r/20161130210030.351136722@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Install the callbacks via the state machine. The notifier in struct
ring_buffer is replaced by the multi instance interface. Upon
__ring_buffer_alloc() invocation, cpuhp_state_add_instance() will invoke
the trace_rb_cpu_prepare() on each CPU.
This callback may now fail. This means __ring_buffer_alloc() will fail and
cleanup (like previously) and during a CPU up event this failure will not
allow the CPU to come up.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20161126231350.10321-7-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
netlink kernel socket is protected by refcount, not RCU.
Its rcv path is neither protected by RCU. So the synchronize_net()
is just pointless.
Cc: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alarm timers are one of the mechanisms to wake up a system from suspend,
but there exist no tracepoints to analyse which process/thread armed an
alarmtimer.
Add tracepoints for start/cancel/expire of individual alarm timers and one
for tracing the suspend time decision when to resume the system.
The following trace excerpt illustrates the new mechanism:
Binder:3292_2-3304 [000] d..2 149.981123: alarmtimer_cancel:
alarmtimer:ffffffc1319a7800 type:REALTIME
expires:1325463120000000000 now:1325376810370370245
Binder:3292_2-3304 [000] d..2 149.981136: alarmtimer_start:
alarmtimer:ffffffc1319a7800 type:REALTIME
expires:1325376840000000000 now:1325376810370384591
Binder:3292_9-3953 [000] d..2 150.212991: alarmtimer_cancel:
alarmtimer:ffffffc1319a5a00 type:BOOTTIME
expires:179552000000 now:150154008122
Binder:3292_9-3953 [000] d..2 150.213006: alarmtimer_start:
alarmtimer:ffffffc1319a5a00 type:BOOTTIME
expires:179551000000 now:150154025622
system_server-3000 [002] ...1 162.701940: alarmtimer_suspend:
alarmtimer type:REALTIME expires:1325376840000000000
The wakeup time which is selected at suspend time allows to map it back to
the task arming the timer: Binder:3292_2.
[ tglx: Store alarm timer expiry time instead of some useless RTC relative
information, add proper type information for wakeups which are
handled via the clock_nanosleep/freezer and massage the changelog. ]
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Link: http://lkml.kernel.org/r/1480372524-15181-5-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If we have a branch that looks something like this
int foo = map->value;
if (condition) {
foo += blah;
} else {
foo = bar;
}
map->array[foo] = baz;
We will incorrectly assume that the !condition branch is equal to the condition
branch as the register for foo will be UNKNOWN_VALUE in both cases. We need to
adjust this logic to only do this if we didn't do a varlen access after we
processed the !condition branch, otherwise we have different ranges and need to
check the other branch as well.
Fixes: 484611357c ("bpf: allow access into map value arrays")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
kexec_locate_mem_hole will be used by the PowerPC kexec_file_load
implementation to find free memory for the purgatory stack.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is done to simplify the kexec_add_buffer argument list.
Adapt all callers to set up a kexec_buf to pass to kexec_add_buffer.
In addition, change the type of kexec_buf.buffer from char * to void *.
There is no particular reason for it to be a char *, and the change
allows us to get rid of 3 existing casts to char * in the code.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Allow architectures to specify a different memory walking function for
kexec_add_buffer. x86 uses iomem to track reserved memory ranges, but
PowerPC uses the memblock subsystem.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christoph requested lockdep_assert_held() variants that distinguish
between held-for-read or held-for-write.
Provide:
int lock_is_held_type(struct lockdep_map *lock, int read)
which takes the same argument as lock_acquire(.read) and matches it to
the held_lock instance.
Use of this function should be gated by the debug_locks variable. When
that is 0 the return value of the lock_is_held_type() function is
undefined. This is done to allow both negative and positive tests for
holding locks.
By default we provide (positive) lockdep_assert_held{,_exclusive,_read}()
macros.
Requested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
There's a 'not' missing in one paragraph. Add it.
Fixes: 3007098494 ("cgroup: add support for eBPF programs")
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reported-by: Rami Rosen <roszenrami@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables CONFIG_MODVERSIONS again, but allows for missing symbol CRC
information in order to work around the issue that newer binutils
versions seem to occasionally drop the CRC on the floor. binutils 2.26
seems to work fine, while binutils 2.27 seems to break MODVERSIONS of
symbols that have been defined in assembler files.
[ We've had random missing CRC's before - it may be an old problem that
just is now reliably triggered with the weak asm symbols and a new
version of binutils ]
Some day I really do want to remove MODVERSIONS entirely. Sadly, today
does not appear to be that day: Debian people apparently do want the
option to enable MODVERSIONS to make it easier to have external modules
across kernel versions, and this seems to be a fairly minimal fix for
the annoying problem.
Cc: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define AUDIT_SESSIONID in the uapi and add support for specifying user
filters based on the session ID. Also add the new session ID filter
to the feature bitmap so userspace knows it is available.
https://github.com/linux-audit/audit-kernel/issues/4
RFE: add a session ID filter to the kernel's user filter
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
[PM: combine multiple patches from Richard into this one]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Unlike monotonic clock, boot clock as a trace clock will account for
time spent in suspend useful for tracing suspend/resume. This uses
earlier introduced infrastructure for using the fast boot clock.
Signed-off-by: Joel Fernandes <joelaf@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Link: http://lkml.kernel.org/r/1480372524-15181-7-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This boot clock can be used as a tracing clock and will account for
suspend time.
To keep it NMI safe since we're accessing from tracing, we're not using a
separate timekeeper with updates to monotonic clock and boot offset
protected with seqlocks. This has the following minor side effects:
(1) Its possible that a timestamp be taken after the boot offset is updated
but before the timekeeper is updated. If this happens, the new boot offset
is added to the old timekeeping making the clock appear to update slightly
earlier:
CPU 0 CPU 1
timekeeping_inject_sleeptime64()
__timekeeping_inject_sleeptime(tk, delta);
timestamp();
timekeeping_update(tk, TK_CLEAR_NTP...);
(2) On 32-bit systems, the 64-bit boot offset (tk->offs_boot) may be
partially updated. Since the tk->offs_boot update is a rare event, this
should be a rare occurrence which postprocessing should be able to handle.
Signed-off-by: Joel Fernandes <joelaf@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1480372524-15181-6-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Idle injection drivers such as Intel powerclamp and ACPI PAD drivers use
realtime tasks to take control of CPU then inject idle. There are two
issues with this approach:
1. Low efficiency: injected idle task is treated as busy so sched ticks
do not stop during injected idle period, the result of these
unwanted wakeups can be ~20% loss in power savings.
2. Idle accounting: injected idle time is presented to user as busy.
This patch addresses the issues by introducing a new PF_IDLE flag which
allows any given task to be treated as idle task while the flag is set.
Therefore, idle injection tasks can run through the normal flow of NOHZ
idle enter/exit to get the correct accounting as well as tick stop when
possible.
The implication is that idle task is then no longer limited to PID == 0.
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When idle injection is used to cap power, we need to override the
governor's choice of idle states.
For this reason, make it possible the deepest idle state selection to
be enforced by setting a flag on a given CPU to achieve the maximum
potential power draw reduction.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since we recently converted the BPF filesystem over to use mount_nodev(),
we now have the possibility to also hold mount options in sb's s_fs_info.
This work implements mount options support for specifying permissions on
the sb's inode, which will be used by tc when it manually needs to mount
the fs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow for checking the owner_prog_type of a program array map. In some
cases bpf(2) can return -EINVAL /after/ the verifier passed and did all
the rewrites of the bpf program.
The reason that lets us fail at this late stage is that program array
maps are incompatible. Allow users to inspect this earlier after they
got the map fd through BPF_OBJ_GET command. tc will get support for this.
Also, display how much we charged the map with regards to RLIMIT_MEMLOCK.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since long already bpf_func is not only about struct sk_buff * as
input anymore. Make it generic as void *, so that callers don't
need to cast for it each time they call BPF_PROG_RUN().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current "rodata=off" parameter disables read-only kernel mappings
under CONFIG_DEBUG_RODATA:
commit d2aa1acad2 ("mm/init: Add 'rodata=off' boot cmdline parameter
to disable read-only kernel mappings")
This patch is a logical extension to module mappings ie. read-only mappings
at module loading can be disabled even if CONFIG_DEBUG_SET_MODULE_RONX
(mainly for debug use). Please note, however, that it only affects RO/RW
permissions, keeping NX set.
This is the first step to make CONFIG_DEBUG_SET_MODULE_RONX mandatory
(always-on) in the future as CONFIG_DEBUG_RODATA on x86 and arm64.
Suggested-by: and Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Link: http://lkml.kernel.org/r/20161114061505.15238-1-takahiro.akashi@linaro.org
Signed-off-by: Jessica Yu <jeyu@redhat.com>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment above strong_try_module_get() function is not true anymore.
Return values changed with commit c9a3ba55bb ("module: wait for
dependent modules doing init.").
Signed-off-by: Miroslav Benes <mbenes@suse.cz>
Link: http://lkml.kernel.org/r/alpine.LNX.2.00.1611161635330.12580@pobox.suse.cz
[jeyu@redhat.com: style fixes to make checkpatch.pl happy]
Signed-off-by: Jessica Yu <jeyu@redhat.com>
By default, during the access permission modification of a module's core
and init pages, we only ignore modules that are malformed. Albeit for a
module which is going away, it does not make sense to change its text to
RO since the module should be RW, before deallocation.
This patch makes set_all_modules_text_ro() skip modules which are going
away too.
Signed-off-by: Aaron Tomlin <atomlin@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Link: http://lkml.kernel.org/r/1477560966-781-1-git-send-email-atomlin@redhat.com
[jeyu@redhat.com: add comment as suggested by Steven Rostedt]
Signed-off-by: Jessica Yu <jeyu@redhat.com>
In load_module() in the event of an error, for e.g. unknown module
parameter(s) specified we go to perform some module coming clean up
operations. At this point the module is still in a "formed" state
when it is actually going away.
This patch updates the module's state accordingly to ensure anyone on the
module_notify_list waiting for a module going away notification will be
notified accordingly.
Signed-off-by: Aaron Tomlin <atomlin@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Link: http://lkml.kernel.org/r/1476980293-19062-2-git-send-email-atomlin@redhat.com
Signed-off-by: Jessica Yu <jeyu@redhat.com>
The commit 66cc69e34e ("Fix: module signature vs tracepoints:
add new TAINT_UNSIGNED_MODULE") updated module_taint_flags() to
potentially print one more character. But it did not increase the
size of the corresponding buffers in m_show() and print_modules().
We have recently done the same mistake when adding a taint flag
for livepatching, see
https://lkml.kernel.org/r/cfba2c823bb984690b73572aaae1db596b54a082.1472137475.git.jpoimboe@redhat.com
Also struct module uses an incompatible type for mod-taints flags.
It survived from the commit 2bc2d61a96 ("[PATCH] list module
taint flags in Oops/panic"). There was used "int" for the global taint
flags at these times. But only the global tain flags was later changed
to "unsigned long" by the commit 25ddbb18aa ("Make the taint
flags reliable").
This patch defines TAINT_FLAGS_COUNT that can be used to create
arrays and buffers of the right size. Note that we could not use
enum because the taint flag indexes are used also in assembly code.
Then it reworks the table that describes the taint flags. The TAINT_*
numbers can be used as the index. Instead, we add information
if the taint flag is also shown per-module.
Finally, it uses "unsigned long", bit operations, and the updated
taint_flags table also for mod->taints.
It is not optimal because only few taint flags can be printed by
module_taint_flags(). But better be on the safe side. IMHO, it is
not worth the optimization and this is a good compromise.
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: http://lkml.kernel.org/r/1474458442-21581-1-git-send-email-pmladek@suse.com
[jeyu@redhat.com: fix broken lkml link in changelog]
Signed-off-by: Jessica Yu <jeyu@redhat.com>
Extend the bpf(2) syscall by two new commands, BPF_PROG_ATTACH and
BPF_PROG_DETACH which allow attaching and detaching eBPF programs
to a target.
On the API level, the target could be anything that has an fd in
userspace, hence the name of the field in union bpf_attr is called
'target_fd'.
When called with BPF_ATTACH_TYPE_CGROUP_INET_{E,IN}GRESS, the target is
expected to be a valid file descriptor of a cgroup v2 directory which
has the bpf controller enabled. These are the only use-cases
implemented by this patch at this point, but more can be added.
If a program of the given type already exists in the given cgroup,
the program is swapped automically, so userspace does not have to drop
an existing program first before installing a new one, which would
otherwise leave a gap in which no program is attached.
For more information on the propagation logic to subcgroups, please
refer to the bpf cgroup controller implementation.
The API is guarded by CAP_NET_ADMIN.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds two sets of eBPF program pointers to struct cgroup.
One for such that are directly pinned to a cgroup, and one for such
that are effective for it.
To illustrate the logic behind that, assume the following example
cgroup hierarchy.
A - B - C
\ D - E
If only B has a program attached, it will be effective for B, C, D
and E. If D then attaches a program itself, that will be effective for
both D and E, and the program in B will only affect B and C. Only one
program of a given type is effective for a cgroup.
Attaching and detaching programs will be done through the bpf(2)
syscall. For now, ingress and egress inet socket filtering are the
only supported use-cases.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rectifies a comment present in sugov_irq_work() function to
follow proper grammar.
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We generalize the scheduler's asym packing to provide an ordering
of the cpu beyond just the cpu number. This allows the use of the
ASYM_PACKING scheduler machinery to move loads to preferred CPU in a
sched domain. The preference is defined with the cpu priority
given by arch_asym_cpu_priority(cpu).
We also record the most preferred cpu in a sched group when
we build the cpu's capacity for fast lookup of preferred cpu
during load balancing.
Co-developed-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: linux-pm@vger.kernel.org
Cc: jolsa@redhat.com
Cc: rjw@rjwysocki.net
Cc: linux-acpi@vger.kernel.org
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: bp@suse.de
Link: http://lkml.kernel.org/r/0e73ae12737dfaafa46c07066cc7c5d3f1675e46.1479844244.git.tim.c.chen@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Michael Kerrisk reported:
> Regarding the previous paragraph... My tests indicate
> that writing *any* value to the autogroup [nice priority level]
> file causes the task group to get a lower priority.
Because autogroup didn't call the then meaningless scale_load()...
Autogroup nice level adjustment has been broken ever since load
resolution was increased for 64-bit kernels. Use scale_load() to
scale group weight.
Michael Kerrisk tested this patch to fix the problem:
> Applied and tested against 4.9-rc6 on an Intel u7 (4 cores).
> Test setup:
>
> Terminal window 1: running 40 CPU burner jobs
> Terminal window 2: running 40 CPU burner jobs
> Terminal window 1: running 1 CPU burner job
>
> Demonstrated that:
> * Writing "0" to the autogroup file for TW1 now causes no change
> to the rate at which the process on the terminal consume CPU.
> * Writing -20 to the autogroup file for TW1 caused those processes
> to get the lion's share of CPU while TW2 TW3 get a tiny amount.
> * Writing -20 to the autogroup files for TW1 and TW3 allowed the
> process on TW3 to get as much CPU as it was getting as when
> the autogroup nice values for both terminals were 0.
Reported-by: Michael Kerrisk <mtk.manpages@gmail.com>
Tested-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-man <linux-man@vger.kernel.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1479897217.4306.6.camel@gmx.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Both rb_end_commit() and rb_set_commit_to_write() are in the fast path of
the ring buffer recording. Make sure they are always inlined.
Link: http://lkml.kernel.org/r/20161121183700.GW26852@two.firstfloor.org
Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The function rb_update_write_stamp() is in the hotpath of the ring buffer
recording. Make sure that it is inlined as well. There's not many places
that call it.
Link: http://lkml.kernel.org/r/20161121183700.GW26852@two.firstfloor.org
Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
There's several small helper functions in ring_buffer.c that are used in the
hot path. For some reason, even though they are marked inline, gcc tends not
to enforce it. Make sure these functions are always inlined.
Link: http://lkml.kernel.org/r/20161121183700.GW26852@two.firstfloor.org
Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The function __buffer_unlock_commit() is called in a few places outside of
trace.c. But for the most part, it should really be inlined, as it is in the
hot path of the trace_events. For the callers outside of trace.c, create a
new function trace_buffer_unlock_commit_nostack(), as the reason it was used
was to avoid the stack tracing that trace_buffer_unlock_commit() could do.
Link: http://lkml.kernel.org/r/20161121183700.GW26852@two.firstfloor.org
Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Currently, when tracepoint_printk is set (enabled by the "tp_printk" kernel
command line), it causes trace events to print via printk(). This is a very
dangerous operation, but is useful for debugging.
The issue is, it's seldom used, but it is always checked even if it's not
enabled by the kernel command line. Instead of having this feature called by
a branch against a variable, turn that variable into a static key, and this
will remove the test and jump.
To simplify things, the functions output_printk() and
trace_event_buffer_commit() were moved from trace_events.c to trace.c.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The rb_event_data() is the fast path of getting the ring buffer data from an
event. Externally, ring_buffer_event_data() is used to access this function.
But unfortunately, rb_event_data() is not inlined, and calling
ring_buffer_event_data() causes that function to be called again. Force
rb_event_data() to be inlined to lower the number of operations needed when
calling ring_buffer_event_data().
Link: http://lkml.kernel.org/r/20161121183700.GW26852@two.firstfloor.org
Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The function rb_reserved_next_event() is called by two functions:
ring_buffer_lock_reserve() and ring_buffer_write(). This is in a very hot
path of the tracing code, and it is best that they are not functions. The
two callers are basically wrapers for rb_reserver_next_event(). Removing the
function calls can save execution time in the hotpath of tracing.
Link: http://lkml.kernel.org/r/20161121183700.GW26852@two.firstfloor.org
Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
As Andi Kleen pointed out in the Link below, the trace events has quite a
bit of code execution. A lot of that happens to be calling functions, where
some of them should simply be inlined. One of these functions happens to be
trace_buffer_lock_reserve() which is also a global, but it is used
throughout the file it is defined in. Create a __trace_buffer_lock_reserve()
that is always inlined that the file can benefit from.
Link: http://lkml.kernel.org/r/20161121183700.GW26852@two.firstfloor.org
Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Pull perf fixes from Ingo Molnar:
"Six fixes for bugs that were found via fuzzing, and a trivial
hw-enablement patch for AMD Family-17h CPU PMUs"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Allow only a single PMU/box within an events group
perf/x86/intel: Cure bogus unwind from PEBS entries
perf/x86: Restore TASK_SIZE check on frame pointer
perf/core: Fix address filter parser
perf/x86: Add perf support for AMD family-17h processors
perf/x86/uncore: Fix crash by removing bogus event_list[] handling for SNB client uncore IMC
perf/core: Do not set cpuctx->cgrp for unscheduled cgroups
No change in functionality:
- align the default values vertically to make them easier to scan
- standardize the 'default:' lines
- fix minor whitespace typos
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull RCU updates from Paul E. McKenney:
- Documentation updates, yet again just simple changes.
- Miscellaneous fixes, including a change to call_rcu()'s
rcu_head alignment check.
- Security-motivated list consistency checks, which are
disabled by default behind DEBUG_LIST.
- Torture-test updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The creation of the set_event_pid file was assigned to a variable "entry"
but that variable was never used. Ideally, it should be used to check if the
file was created and warn if it was not.
The files header_page, header_event should also be checked and a warning if
they fail to be created.
The "enable" file was moved up, as it is a more crucial file to have and a
hard failure (return -ENOMEM) should be returned if it is not created.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Currently Function traces can be only exported to the ring buffer. This
adds a trace_export concept which can process traces and export
them to a registered destination as an addition to the current
one that outputs to Ftrace - i.e. ring buffer.
In this way, if we want function traces to be sent to other destinations
rather than only to the ring buffer, we just need to register a new
trace_export and implement its own .write() function for writing traces to
storage.
With this patch, only function tracing (trace type is TRACE_FN)
is supported.
Link: http://lkml.kernel.org/r/1479715043-6534-2-git-send-email-zhang.chunyan@linaro.org
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When the user namespace support was merged the need to prevent
ptrace from revealing the contents of an unreadable executable
was overlooked.
Correct this oversight by ensuring that the executed file
or files are in mm->user_ns, by adjusting mm->user_ns.
Use the new function privileged_wrt_inode_uidgid to see if
the executable is a member of the user namespace, and as such
if having CAP_SYS_PTRACE in the user namespace should allow
tracing the executable. If not update mm->user_ns to
the parent user namespace until an appropriate parent is found.
Cc: stable@vger.kernel.org
Reported-by: Jann Horn <jann@thejh.net>
Fixes: 9e4a36ece6 ("userns: Fail exec for suid and sgid binaries with ids outside our user namespace.")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
It is the reasonable expectation that if an executable file is not
readable there will be no way for a user without special privileges to
read the file. This is enforced in ptrace_attach but if ptrace
is already attached before exec there is no enforcement for read-only
executables.
As the only way to read such an mm is through access_process_vm
spin a variant called ptrace_access_vm that will fail if the
target process is not being ptraced by the current process, or
the current process did not have sufficient privileges when ptracing
began to read the target processes mm.
In the ptrace implementations replace access_process_vm by
ptrace_access_vm. There remain several ptrace sites that still use
access_process_vm as they are reading the target executables
instructions (for kernel consumption) or register stacks. As such it
does not appear necessary to add a permission check to those calls.
This bug has always existed in Linux.
Fixes: v1.0
Cc: stable@vger.kernel.org
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the flag PT_PTRACE_CAP was added the PTRACE_TRACEME path was
overlooked. This can result in incorrect behavior when an application
like strace traces an exec of a setuid executable.
Further PT_PTRACE_CAP does not have enough information for making good
security decisions as it does not report which user namespace the
capability is in. This has already allowed one mistake through
insufficient granulariy.
I found this issue when I was testing another corner case of exec and
discovered that I could not get strace to set PT_PTRACE_CAP even when
running strace as root with a full set of caps.
This change fixes the above issue with strace allowing stracing as
root a setuid executable without disabling setuid. More fundamentaly
this change allows what is allowable at all times, by using the correct
information in it's decision.
Cc: stable@vger.kernel.org
Fixes: 4214e42f96d4 ("v2.4.9.11 -> v2.4.9.12")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
During exec dumpable is cleared if the file that is being executed is
not readable by the user executing the file. A bug in
ptrace_may_access allows reading the file if the executable happens to
enter into a subordinate user namespace (aka clone(CLONE_NEWUSER),
unshare(CLONE_NEWUSER), or setns(fd, CLONE_NEWUSER).
This problem is fixed with only necessary userspace breakage by adding
a user namespace owner to mm_struct, captured at the time of exec, so
it is clear in which user namespace CAP_SYS_PTRACE must be present in
to be able to safely give read permission to the executable.
The function ptrace_may_access is modified to verify that the ptracer
has CAP_SYS_ADMIN in task->mm->user_ns instead of task->cred->user_ns.
This ensures that if the task changes it's cred into a subordinate
user namespace it does not become ptraceable.
The function ptrace_attach is modified to only set PT_PTRACE_CAP when
CAP_SYS_PTRACE is held over task->mm->user_ns. The intent of
PT_PTRACE_CAP is to be a flag to note that whatever permission changes
the task might go through the tracer has sufficient permissions for
it not to be an issue. task->cred->user_ns is always the same
as or descendent of mm->user_ns. Which guarantees that having
CAP_SYS_PTRACE over mm->user_ns is the worst case for the tasks
credentials.
To prevent regressions mm->dumpable and mm->user_ns are not considered
when a task has no mm. As simply failing ptrace_may_attach causes
regressions in privileged applications attempting to read things
such as /proc/<pid>/stat
Cc: stable@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Tested-by: Cyrill Gorcunov <gorcunov@openvz.org>
Fixes: 8409cca705 ("userns: allow ptrace from non-init user namespaces")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
An over-committed guest with more vCPUs than pCPUs has a heavy overload
in osq_lock().
This is because if vCPU-A holds the osq lock and yields out, vCPU-B ends
up waiting for per_cpu node->locked to be set. IOW, vCPU-B waits for
vCPU-A to run and unlock the osq lock.
Use the new vcpu_is_preempted(cpu) interface to detect if a vCPU is
currently running or not, and break out of the spin-loop if so.
test case:
$ perf record -a perf bench sched messaging -g 400 -p && perf report
before patch:
18.09% sched-messaging [kernel.vmlinux] [k] osq_lock
12.28% sched-messaging [kernel.vmlinux] [k] rwsem_spin_on_owner
5.27% sched-messaging [kernel.vmlinux] [k] mutex_unlock
3.89% sched-messaging [kernel.vmlinux] [k] wait_consider_task
3.64% sched-messaging [kernel.vmlinux] [k] _raw_write_lock_irq
3.41% sched-messaging [kernel.vmlinux] [k] mutex_spin_on_owner.is
2.49% sched-messaging [kernel.vmlinux] [k] system_call
after patch:
20.68% sched-messaging [kernel.vmlinux] [k] mutex_spin_on_owner
8.45% sched-messaging [kernel.vmlinux] [k] mutex_unlock
4.12% sched-messaging [kernel.vmlinux] [k] system_call
3.01% sched-messaging [kernel.vmlinux] [k] system_call_common
2.83% sched-messaging [kernel.vmlinux] [k] copypage_power7
2.64% sched-messaging [kernel.vmlinux] [k] rwsem_spin_on_owner
2.00% sched-messaging [kernel.vmlinux] [k] osq_lock
Suggested-by: Boqun Feng <boqun.feng@gmail.com>
Tested-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Pan Xinhui <xinhui.pan@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: David.Laight@ACULAB.COM
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: benh@kernel.crashing.org
Cc: bsingharora@gmail.com
Cc: dave@stgolabs.net
Cc: kernellwp@gmail.com
Cc: konrad.wilk@oracle.com
Cc: linuxppc-dev@lists.ozlabs.org
Cc: mpe@ellerman.id.au
Cc: paulmck@linux.vnet.ibm.com
Cc: paulus@samba.org
Cc: rkrcmar@redhat.com
Cc: virtualization@lists.linux-foundation.org
Cc: will.deacon@arm.com
Cc: xen-devel-request@lists.xenproject.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1478077718-37424-3-git-send-email-xinhui.pan@linux.vnet.ibm.com
[ Translated to English. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Exactly because for_each_thread() in autogroup_move_group() can't see it
and update its ->sched_task_group before _put() and possibly free().
So the exiting task needs another sched_move_task() before exit_notify()
and we need to re-introduce the PF_EXITING (or similar) check removed by
the previous change for another reason.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: hartsjc@redhat.com
Cc: vbendel@redhat.com
Cc: vlovejoy@redhat.com
Link: http://lkml.kernel.org/r/20161114184612.GA15968@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The PF_EXITING check in task_wants_autogroup() is no longer needed. Remove
it, but see the next patch.
However the comment is correct in that autogroup_move_group() must always
change task_group() for every thread so the sysctl_ check is very wrong;
we can race with cgroups and even sys_setsid() is not safe because a task
running with task_group() == ag->tg must participate in refcounting:
int main(void)
{
int sctl = open("/proc/sys/kernel/sched_autogroup_enabled", O_WRONLY);
assert(sctl > 0);
if (fork()) {
wait(NULL); // destroy the child's ag/tg
pause();
}
assert(pwrite(sctl, "1\n", 2, 0) == 2);
assert(setsid() > 0);
if (fork())
pause();
kill(getppid(), SIGKILL);
sleep(1);
// The child has gone, the grandchild runs with kref == 1
assert(pwrite(sctl, "0\n", 2, 0) == 2);
assert(setsid() > 0);
// runs with the freed ag/tg
for (;;)
sleep(1);
return 0;
}
crashes the kernel. It doesn't really need sleep(1), it doesn't matter if
autogroup_move_group() actually frees the task_group or this happens later.
Reported-by: Vern Lovejoy <vlovejoy@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: hartsjc@redhat.com
Cc: vbendel@redhat.com
Link: http://lkml.kernel.org/r/20161114184609.GA15965@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The generic MSI layer doesn't have any PCI ties anymore, and the
build hack should have been removed some time ago.
Fixes: d9109698be ("genirq: Introduce msi_domain_alloc/free_irqs()")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1479806476-20801-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull sparc fixes from David Miller:
1) With modern networking cards we can run out of 32-bit DMA space, so
support 64-bit DMA addressing when possible on sparc64. From Dave
Tushar.
2) Some signal frame validation checks are inverted on sparc32, fix
from Andreas Larsson.
3) Lockdep tables can get too large in some circumstances on sparc64,
add a way to adjust the size a bit. From Babu Moger.
4) Fix NUMA node probing on some sun4v systems, from Thomas Tai.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: drop duplicate header scatterlist.h
lockdep: Limit static allocations if PROVE_LOCKING_SMALL is defined
config: Adding the new config parameter CONFIG_PROVE_LOCKING_SMALL for sparc
sunbmac: Fix compiler warning
sunqe: Fix compiler warnings
sparc64: Enable 64-bit DMA
sparc64: Enable sun4v dma ops to use IOMMU v2 APIs
sparc64: Bind PCIe devices to use IOMMU v2 service
sparc64: Initialize iommu_map_table and iommu_pool
sparc64: Add ATU (new IOMMU) support
sparc64: Add FORCE_MAX_ZONEORDER and default to 13
sparc64: fix compile warning section mismatch in find_node()
sparc32: Fix inverted invalid_frame_pointer checks on sigreturns
sparc64: Fix find_node warning if numa node cannot be found
Modify the ACPI system sleep support setup code to select
suspend-to-idle as the default system sleep state if the
ACPI_FADT_LOW_POWER_S0 flag is set in the FADT and the
default sleep state was not selected from the kernel command
line.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
There are systems in which the platform doesn't support any special
sleep states, so suspend-to-idle (PM_SUSPEND_FREEZE) is the only
available system sleep state. However, some user space frameworks
only use the "mem" and (sometimes) "standby" sleep state labels, so
the users of those systems need to modify user space in order to be
able to use system suspend at all and that may be a pain in practice.
Commit 0399d4db3e (PM / sleep: Introduce command line argument for
sleep state enumeration) attempted to address this problem by adding
a command line argument to change the meaning of the "mem" string in
/sys/power/state to make it trigger suspend-to-idle (instead of
suspend-to-RAM).
However, there also are systems in which the platform does support
special sleep states, but suspend-to-idle is the preferred one anyway
(it even may save more energy than the platform-provided sleep states
in some cases) and the above commit doesn't help in those cases.
For this reason, rework the system sleep state selection interface
again (but preserve backwards compatibiliby). Namely, add a new
sysfs file, /sys/power/mem_sleep, that will control the system
suspend mode triggered by writing "mem" to /sys/power/state (in
analogy with what /sys/power/disk does for hibernation). Make it
select suspend-to-RAM ("deep" sleep) by default (if supported) and
fall back to suspend-to-idle ("s2idle") otherwise and add a new
command line argument, mem_sleep_default, allowing that default to
be overridden if need be.
At the same time, drop the relative_sleep_states command line
argument that doesn't make sense any more.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Pull networking fixes from David Miller:
1) Clear congestion control state when changing algorithms on an
existing socket, from Florian Westphal.
2) Fix register bit values in altr_tse_pcs portion of stmmac driver,
from Jia Jie Ho.
3) Fix PTP handling in stammc driver for GMAC4, from Giuseppe
CAVALLARO.
4) Fix udplite multicast delivery handling, it ignores the udp_table
parameter passed into the lookups, from Pablo Neira Ayuso.
5) Synchronize the space estimated by rtnl_vfinfo_size and the space
actually used by rtnl_fill_vfinfo. From Sabrina Dubroca.
6) Fix memory leak in fib_info when splitting nodes, from Alexander
Duyck.
7) If a driver does a napi_hash_del() explicitily and not via
netif_napi_del(), it must perform RCU synchronization as needed. Fix
this in virtio-net and bnxt drivers, from Eric Dumazet.
8) Likewise, it is not necessary to invoke napi_hash_del() is we are
also doing neif_napi_del() in the same code path. Remove such calls
from be2net and cxgb4 drivers, also from Eric Dumazet.
9) Don't allocate an ID in peernet2id_alloc() if the netns is dead,
from WANG Cong.
10) Fix OF node and device struct leaks in of_mdio, from Johan Hovold.
11) We cannot cache routes in ip6_tunnel when using inherited traffic
classes, from Paolo Abeni.
12) Fix several crashes and leaks in cpsw driver, from Johan Hovold.
13) Splice operations cannot use freezable blocking calls in AF_UNIX,
from WANG Cong.
14) Link dump filtering by master device and kind support added an error
in loop index updates during the dump if we actually do filter, fix
from Zhang Shengju.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
tcp: zero ca_priv area when switching cc algorithms
net: l2tp: Treat NET_XMIT_CN as success in l2tp_eth_dev_xmit
ethernet: stmmac: make DWMAC_STM32 depend on it's associated SoC
tipc: eliminate obsolete socket locking policy description
rtnl: fix the loop index update error in rtnl_dump_ifinfo()
l2tp: fix racy SOCK_ZAPPED flag check in l2tp_ip{,6}_bind()
net: macb: add check for dma mapping error in start_xmit()
rtnetlink: fix FDB size computation
netns: fix get_net_ns_by_fd(int pid) typo
af_unix: conditionally use freezable blocking calls in read
net: ethernet: ti: cpsw: fix fixed-link phy probe deferral
net: ethernet: ti: cpsw: add missing sanity check
net: ethernet: ti: cpsw: fix secondary-emac probe error path
net: ethernet: ti: cpsw: fix of_node and phydev leaks
net: ethernet: ti: cpsw: fix deferred probe
net: ethernet: ti: cpsw: fix mdio device reference leak
net: ethernet: ti: cpsw: fix bad register access in probe error path
net: sky2: Fix shutdown crash
cfg80211: limit scan results cache size
net sched filters: pass netlink message flags in event notification
...
In mlx5e_create_rq(), when creating a new queue, we call bpf_prog_add() but
without checking the return value. bpf_prog_add() can fail since 92117d8443
("bpf: fix refcnt overflow"), so we really must check it. Take the reference
right when we assign it to the rq from priv->xdp_prog, and just drop the
reference on error path. Destruction in mlx5e_destroy_rq() looks good, though.
Fixes: 86994156c7 ("net/mlx5e: XDP fast RX drop bpf programs support")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The token table passed into match_token() must be null-terminated, which
it currently is not in the perf's address filter string parser, as caught
by Vince's perf_fuzzer and KASAN.
It doesn't blow up otherwise because of the alignment padding of the table
to the next element in the .rodata, which is luck.
Fixing by adding a null-terminator to the token table.
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Tested-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dvyukov@google.com
Cc: stable@vger.kernel.org # v4.7+
Fixes: 375637bc52 ("perf/core: Introduce address range filtering")
Link: http://lkml.kernel.org/r/877f81f264.fsf@ashishki-desk.ger.corp.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently the wake_q data structure is defined by the WAKE_Q() macro.
This macro, however, looks like a function doing something as "wake" is
a verb. Even checkpatch.pl was confused as it reported warnings like
WARNING: Missing a blank line after declarations
#548: FILE: kernel/futex.c:3665:
+ int ret;
+ WAKE_Q(wake_q);
This patch renames the WAKE_Q() macro to DEFINE_WAKE_Q() which clarifies
what the macro is doing and eliminates the checkpatch.pl warnings.
Signed-off-by: Waiman Long <longman@redhat.com>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1479401198-1765-1-git-send-email-longman@redhat.com
[ Resolved conflict and added missing rename. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The AUDIT_CONFIG_CHANGE events sometimes use a op= field. The current
code logs the value of the field with quotes. This field is documented
to not be encoded, so it should not have quotes.
Signed-off-by: Steve Grubb <sgrubb@redhat.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
[PM: reformatted commit description to make checkpatch.pl happy]
Signed-off-by: Paul Moore <paul@paul-moore.com>
The value (unsigned int)-1 is used as a sentinel to indicate the
sessionID is unset. Skip this value when the session_id value wraps.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Reduce the size of data structure for lockdep entries by half if
PROVE_LOCKING_SMALL if defined. This is used only for sparc.
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore